Friction stir lap welding of AA2195 Al-Li alloy and Ti alloy was conducted to investigate the formation,microstructure,and mechanical properties of the joints.Results show that under different welding parameters,with ...Friction stir lap welding of AA2195 Al-Li alloy and Ti alloy was conducted to investigate the formation,microstructure,and mechanical properties of the joints.Results show that under different welding parameters,with the decrease in welding heat input,the weld surface is smoother.The Ti/Al joint interface is flat without obvious Ti and Al mixed structure,and the hook structure is not formed under optimal parameters.Due to the enhanced breaking effect of the stirring head,the hook structural defects and intermetallic compounds are more likely to form at the Ti/Al interface at high rotational speed of 1000 r/min,thereby deteriorating the mechanical properties of joints.Decreasing the heat input is beneficial to hardness enhancement of the aluminum alloy in the weld nugget zone.Under the optimal parameters of rotation speed of 800 r/min and welding speed of 120 mm/min,the maximum tensile shear strength of joint is 289 N/mm.展开更多
1.Introduction The strength-ductility trade-offdilemma has long been a per-sistent challenge in Al matrix composites(AMCs)[1,2].This is-sue primarily arises from the agglomeration of reinforcements at the grain bounda...1.Introduction The strength-ductility trade-offdilemma has long been a per-sistent challenge in Al matrix composites(AMCs)[1,2].This is-sue primarily arises from the agglomeration of reinforcements at the grain boundaries(GBs),which restricts local plastic flow dur-ing the plastic deformation and leads to stress concentration[3,4].Recently,the development of concepts aimed at achieving hetero-geneous grain has emerged as a promising approach for enhanc-ing comprehensive mechanical properties[5,6].展开更多
Zinc(Zn)-based materials show broad application prospects for bone repair due to their biodegradability and good biocompatibility.In particular,Zn metal foam has unique interconnected pore structure that facilitates i...Zinc(Zn)-based materials show broad application prospects for bone repair due to their biodegradability and good biocompatibility.In particular,Zn metal foam has unique interconnected pore structure that facilitates inward growth of new bone tissue,making it ideal candidates for orthopedic implants.However,pure Zn metal foam shows poor mechanical property,high degradation rate,and unsatisfactory osteogenic activity.Herein,Zinc-manganese(Zn-Mn)alloy foams were electrodeposited in Zn and Mn-containing electrolytes to overcome the concerns.The results showed that Mn could be incorporated into the foams in the form of MnZn_(13).Zn-Mn alloy foams showed better mechanical property and osteogenic activity as well as moderate degradation rate when compared with pure Zn metal foam.In addition,these properties could also be regulated by preparation process.The peak stress and osteogenic activity increased with deposition current(0.3‒0.5 A)and electrolyte pH(3‒5),but decreased with electrolyte temperature(20‒40℃),while the degradation rate exhibited opposite tendency,which suggests high deposition current and electrolyte pH and low electrolyte temperature can fabricate Zn-Mn alloy foam with favorable mechanical property,moderate degradation rate,and osteogenic activity.These findings provide a valuable reference for the design and fabrication of novel Zn-based biodegradable materials.展开更多
The surface of MoSi2-SiB6/phenolic resin matrix composites was modified by mica,and the thermal oxidation behavior of the composites and the mechanical properties of the pyrolysis products were studied.The results sho...The surface of MoSi2-SiB6/phenolic resin matrix composites was modified by mica,and the thermal oxidation behavior of the composites and the mechanical properties of the pyrolysis products were studied.The results showed that the mica improved the thermal properties of the composites,the thermal expansion coefficient decreased,and the liquid phase formation caused the composites to shrink and increase the density.The flexural strength of mica surface modified composites not only increased to 78.64MPa after thermal treatment at 800-1200℃,but reached 83.02 MPa after high temperature treatment at1400℃.The improvement of the mechanical properties of the residual product benefits from the formation of high temperature ceramic phases such as Mo_(2)C and MoB,and the improvement of the shear strength of the composites by the mica.The shear strength of MBm5-2 at room temperature reached 33.08 MPa,indicating that the improvement of the interlayer properties of the composites further improved its mechanical properties.展开更多
This study develops novel Mg-Sn-In-Ga alloys as potential implant materials for orthopedic applications.The corrosion behavior of the Mg-Sn-In-Ga alloys was studied through mass loss measurements,hydrogen evolution me...This study develops novel Mg-Sn-In-Ga alloys as potential implant materials for orthopedic applications.The corrosion behavior of the Mg-Sn-In-Ga alloys was studied through mass loss measurements,hydrogen evolution measurements,electrochemical analysis,and corrosion morphology observations.The results show that the corrosion rate of the Mg-1Sn-1In-1Ga alloy was only 0.10±0.003 mm/y after immersion in Hank’s solution for 15 days.This outstanding corrosion resistance was associated with the protective efect of the corrosion products.The increase in the Sn and Ga element content led to the precipitation of a large amount of Mg_(2)Sn and Mg_(5)Ga_(2),which had a dominant efect on the corrosion rate in the Mg-5Sn-1In-2Ga alloy.These precipitates increased the current density and detached from the alloy surface during the corrosion process.This can lead to a weakened protective efect of the corrosion layer,and thus generate localized corrosion and an increase in the corrosion rate.The strength of the Mg-5Sn-1In-2Ga alloy was enhanced due to fne-grain strengthening and precipitation strengthening.The ultimate tensile strength and yield strength of the Mg-5Sn-1In-2Ga alloy were~309 MPa and~253 MPa,respectively.展开更多
Biomedical materials may suffer from stress-induced corrosion when performing as implant materials at load-bearing sites, bringing about variations in the microstructure, corrosion resistance, and mechanical propertie...Biomedical materials may suffer from stress-induced corrosion when performing as implant materials at load-bearing sites, bringing about variations in the microstructure, corrosion resistance, and mechanical properties. In this study, the corrosion behavior and mechanical properties of an extruded Mg-4Li-1Ca alloy were investigated under different micro-compressive stresses (0-6 MPa) using a novel homemade loading device. Under 0-3 MPa of micro-compressive stress, the strong basal texture of extruded Mg-4Li1Ca alloys was weakened and the internal stress gradient stimulated grain boundary migration to induce grain growth. Meanwhile, increased stress resulted in the precipitation of second-phase particles and the accumulation of residual stress, accelerating the corrosion rate due to preferential corrosion. However, with increasing stress, the volume fraction of the second phase increased, becoming the dominant factor controlling the corrosion rate, and residual stress was released for samples under 4.5-6 MPa of microcompressive stress. Hence, surface corrosion product films rapidly formed and served as effective physical barriers, weakening the microstructural effect on the corrosion behavior. The yield strength of Mg-4Li-1Ca alloy reached 95.48 MPa under 3 MPa of micro-compressive stress owing to the dual effects of precipitation strengthening and shear-band strengthening. The relationships between microstructure, corrosion behavior, and mechanical property provide a theoretical foundation for understanding the degradation characteristics of the Mg-4Li-1Ca alloy under physiological loading and practical application.展开更多
Dispersion-strengthened copper alloys can achieve ultra-high strength,but usually at the expense of duc-tility.In this study,a strategy for overcoming strength-ductility tradeoffof Cu alloys is realized through the in...Dispersion-strengthened copper alloys can achieve ultra-high strength,but usually at the expense of duc-tility.In this study,a strategy for overcoming strength-ductility tradeoffof Cu alloys is realized through the introduction of bimodal grains structures.Cu-Ta alloys with only 0.5 at.%Ta content were successfully prepared by mechanical alloying combined with spark plasm sintering.The samples prepared by one-step and two-step ball milling methods are named as Cu-Ta(Ⅰ)and Cu-Ta(Ⅱ),respectively.The microstructural characterizations revealed that ultra-fine equiaxed grains with uniformly dispersed Ta precipitates were obtained in the Cu-Ta alloys.High strength of 377 MPa for yield strength together with elongation of∼8%was obtained in Cu-Ta(Ⅰ).Bimodal grains structures composed of fine-grain zones and coarse-grain zones were successfully introduced into Cu-Ta(Ⅱ)by a two-step ball milling approach,and both yield strength(463 MPa)and elongation(∼15%)were significantly synergistic enhanced.The hardness values of both Cu-Ta(Ⅰ)and Cu-Ta(Ⅱ)were almost kept nearly constant with the increase of annealing time,and the softening temperatures of Cu-Ta(Ⅰ)and Cu-Ta(Ⅱ)are 1018 and 1013℃,reaching 93.9%and 93.5%T m of pure Cu(1083℃),respectively.It reveals that the Cu-0.5 at.%Ta alloys exhibit excellent thermal stability and exceptional softening resistance.Ta nanoclusters with semi-coherent structures play an essential role in enhancing the strength and microstructural stability of alloys.Bimodal structures are beneficial to the activation of back stress strengthening and the initiation and propagation of microcracks,thus obtaining the extraordinary combination of strength and elongation.This study provides a new way to fabricate dispersion-strengthened Cu alloys with high strength,high elongation,excellent thermal stability and softening resistance,which have potential application value in the field of the future fusion reactor.展开更多
The key role of oxide inclusions on the microstructure and mechanical property of a high-strength low-alloy steel was investigated.The field emission scanning electron microscope equipped with energy-dispersive spectr...The key role of oxide inclusions on the microstructure and mechanical property of a high-strength low-alloy steel was investigated.The field emission scanning electron microscope equipped with energy-dispersive spectrometry was used to characterize MnS precipitates.Oxide inclusions play an important role in the shape control of MnS precipitates.More oxides fovored to decrease the size and the aspect ratio of MnS precipitates.With less oxide inclusions in the steel,approximately over 16.7%MnS precipitates were with aspect ratio a>5 and pure MnS precipitates accounted for 75.9%in number.However,with more oxide inclusions in the steel,only 7.4%MnS precipitates were with a>5 and pure MnS precipitates accounted for 60.1%in number.Refinement of MnS by oxide inclusions improved the strength and inhibited the anisotropy.More oxide inclusions in the steel increased the yield strength and tensile strength of the steel in both longitudinal and transverse directions,and lowered the anisotropy of the mechanical property.展开更多
In this study, the in-situ synthesized ZrB_(2) nanoparticles and rare earth Sc were introduced to enhance the strength and ductility of 7N01 aluminum alloy, via the generation of high-melting and uniform nanodispersoi...In this study, the in-situ synthesized ZrB_(2) nanoparticles and rare earth Sc were introduced to enhance the strength and ductility of 7N01 aluminum alloy, via the generation of high-melting and uniform nanodispersoids. The microstructure and mechanical property evolution of the prepared composites and the interaction between ZrB_(2) and Sc were studied in detail. The microstructure investigation shows that the introduction of rare earth scandium(Sc) can promote the distribution of ZrB_(2) nanoparticles, by improving their wettability to the Al melt. Meanwhile, the addition of rare earth Sc also modifies the coarse Al Zn Mg Mn Fe precipitated phases, refines the matrix grains and generates high-melting Al_3(Sc,Zr)/Al_3Sc nanodispersoids. Tensile tests of the composites show that with the combinatorial introduction of ZrB_(2) and Sc, the strength and ductility of the composites are improved simultaneously compared with the corresponding 7N01 alloy, ZrB_(2) /7N01 composite and Sc/7N01 alloy. And the optimum contents of ZrB_(2) and Sc are 3 wt% and 0.2 wt% in this study. The yield strength, ultimate strength and elongation of(3 wt% ZrB_(2) +0.2 wt% Sc)/7N01 composite are 477 MPa, 506 MPa and 9.8%, increased about 18.1%, 12.2%and 38% compared to 7N01 alloy. Furthermore, the cooperation strengthening mechanisms of ZrB_(2) and Sc are also discussed.展开更多
Carbonated recycled powder as cementitious auxiliary material can reduce carbon emissions and realize high-quality recycling of recycled concrete.In this paper,microscopic property of recycled powder with three carbon...Carbonated recycled powder as cementitious auxiliary material can reduce carbon emissions and realize high-quality recycling of recycled concrete.In this paper,microscopic property of recycled powder with three carbonation methods was tested through XRD and SEM,the mechanical property and microstructure of recycled powder mortar with three replacement rates were studied by ISO method and SEM,and the strengthening mechanism was analyzed.The results showed that the mechanical property of recycled powder mortar decreased with the increasing of replacement rate.It is suggested that the replacement rate of recycled powder should not exceed 20%.The strength index and activity index of carbonated recycled powder mortar were improved,in which the flexural strength was increased by 27.85%and compressive strength was increased by 20%at the maximum.Recycled powder can be quickly and completely carbonated,and the improvement effect of CH pre-soaking carbonation was the best.The activity index of carbonated recycled powder can meet the requirements of Grade II technical standard for recycled powder.Microscopic results revealed the activation mechanism of carbonated recycled powder such as surplus calcium source effect,alkaline polycondensation effect and carbonation enhancement effect.展开更多
The semi-solid stir casting method is adopted to prepare 10 wt%SiC_(p)/Mg-6Zn-0.5Ca-xAl(x=0,1,3 and 5 wt%)composites,and the microstructure evolution and mechanical property of composites with various Al content are i...The semi-solid stir casting method is adopted to prepare 10 wt%SiC_(p)/Mg-6Zn-0.5Ca-xAl(x=0,1,3 and 5 wt%)composites,and the microstructure evolution and mechanical property of composites with various Al content are investigated.The results show that the addition of 3 wt%Al improves the distribution of SiC_(p),whereas the SiC_(p) cluster occurs again with Al content greater than 3%.An abnormal phenomenon of twinning is observed in the cast composites in this work.The SiC_(p)/Mg-6Zn-0.5Ca composite possesses the highest twin content of~23%,for which tension twins(TTW)and compression twins(CTW)account for~19%and~3%,respectively.The CTW is only observed in ZXA600 composite.The addition of Al has an inhibiting effect for the generation and growth of twins.The content of twin decreases firstly and then increases with increase of Al content.The lowest twin content is obtained as Al increases to 3 wt%.It is found the existence of twin is detrimental to the mechanical property of composites.As-cast SiC_(p)/Mg-6Zn-0.5Ca-3Al composite with the lowest twin content exhibits the optimal mechanical property of yield strength,ultimate tensile strength and elongation for 100 MPa,188 MPa and 4.4%,respectively.The outstanding mechanical property is attributed to the uniform distribution of SiC_(p),the low twin content and the well-distributed fine second phases.展开更多
In this work,the microstructure and mechanical properties of large cross-sectioned Mg-9Gd-3Y-1.2Zn-0.5Zr(VWZ931)samples produced by the small extrusion ratio has been investigated.The as-extruded VWZ931 sample with di...In this work,the microstructure and mechanical properties of large cross-sectioned Mg-9Gd-3Y-1.2Zn-0.5Zr(VWZ931)samples produced by the small extrusion ratio has been investigated.The as-extruded VWZ931 sample with diameter of~30 mm can exhibit the high yield strength(YS)of 339 MPa,ultimate tensile strength(UTS)of 387 MPa and elongation of 8.2%,respectively.After peak-aged,the YS and UTS of the Mg samples were significantly increased to 435 MPa and 467 MPa.The small extrusion ratio leads to the low fraction of dynamic recrystallized(DRX)grains in VWZ931 sample,and the texture hardening effect can be fully utilized to achieve high strength.The combined effect of precipitation strengthening due to the long-period stacking ordered phases and theβ′phase,grain boundary strengthening due to the fine DRX grains,heterogeneous deformation-induced strengthening caused by bimodal microstructure,can together contribute to the high strength of present Mg alloy.The findings can shed light on designing other large-sized Mg wrought alloys with high mechanical performance.展开更多
Conventional MgO-C bricks(graphite content>14 wt.%)produce a great deal of greenhouse gas emission,while low-carbon MgO-C bricks have serious thermal shock resistance during high-temperature service.To enhance the ...Conventional MgO-C bricks(graphite content>14 wt.%)produce a great deal of greenhouse gas emission,while low-carbon MgO-C bricks have serious thermal shock resistance during high-temperature service.To enhance the high-temperature mechanical property and thermal shock resistance of low-carbon MgO-C bricks,a novel route of introducing ZrSiO_(4) powder into low-carbon MgO-C bricks was reported in such refractories with 2 wt.% flaky graphite.The results indicate that the low-carbon MgO-C brick with 0.5 wt.%ZrSiO_(4) addition has the maximum hot modulus of rupture at 1400℃ and the corresponding specimen fired in the carbon embedded atmosphere has the maximum residual strength ratio(98.6%)after three thermal shock cycles.It is found that some needle-like AlON and plate-like Al_(2)O_(3)-ZrO_(2) composites were in situ formed in the matrices after the low-carbon MgO-C bricks were coked at 1400℃,which can enhance the high-temperature mechanical property and thermal shock resistance due to the effect of fiber toughening and particle toughening.Moreover,CO_(2) emission of the newly developed low-carbon MgO-C bricks is reduced by 58.3% per ton steel after using them as the working lining of a 90 t vacuum oxygen decarburization ladle.展开更多
Owing to the special layer-by-layer deposition process of directed energy deposition(DED),columnar coarse grains,produced by cyclic reheating with intrinsic directional heat flow along the building direc-tion,are diff...Owing to the special layer-by-layer deposition process of directed energy deposition(DED),columnar coarse grains,produced by cyclic reheating with intrinsic directional heat flow along the building direc-tion,are difficult to avoid.These grains result in strong anisotropic characteristics with poor mechanical properties,which restrict the application of DED products.This work proposes a novel fabrication strat-egy based on the cyclic-phase-transformation behavior,which can reduce the anisotropy and improve the mechanical properties of DED-printed stainless steel.Using this fabrication strategy,316 L powder(austenitic stainless steel)and 17-4PH powder(martensitic stainless steel)were mixed in different mass ratios to fabricate five types of DED-printed stainless steels.Among the five samples,P70(mixture of 70 wt%17-4PH powder and 30 wt%316 L powder)showed the weakest anisotropy and the best mechanical properties,which can be attributed to the cyclic phase transformation under cyclic reheating treatment and the transformation-induced plasticity(TRIP)effect over a wide range of strains,respectively.Com-pared with the pure 316 L printed material,the tensile test results of P70 showed that the yield strength(YS)and ultimate tensile strength(UTS)increased by 35.4%and 34.5%,respectively,whereas the uniform elongation(UE)and total elongation(TE)were improved by 63.9%and 31.4%,respectively.In addition,the strength-ductility balance(UTS×UE)increased by as much as 120.4%.The proposed fabrication strategy is expected to reduce the anisotropy in other materials that undergo cyclic-phase-transformation phe-nomena during additive manufacturing.展开更多
Low temperature mechanical properties of AZ91D magnesium alloy fabricated by solid recycling process from recycled scraps were studied. Various microstructural analyses were performed using optical microscopy （OM） a...Low temperature mechanical properties of AZ91D magnesium alloy fabricated by solid recycling process from recycled scraps were studied. Various microstructural analyses were performed using optical microscopy （OM） and scanning electron microscopy （SEM）. The recycled specimens consist of fine grains due to dynamic recrystallization and the interfaces of original individual scraps are not identified. Tensile tests were performed at a strain rate of 5 x 10 3 s 1 at room temperature （27 ~C）, -70, -100 and 130 ~C, respectively. Ultimate tensile strength of the specimens increases slightly with decreasing the tensile temperature, and elongation to failure decreases with decreasing the tensile temperature. The tensile specimens at -130 ~C show the highest ultimate tensile strength of 360.65 MPa and the lowest elongation to failure of 5.46%. Impact tests were performed at room temperature （27 ~C）, -70 and -130 ~C, respectively. Impact toughness decreases with decreasing the impact temperature. The impact specimens at -130 ~C show the lowest impact toughness of 3.06 J/cm2.展开更多
Microstructures and phase compositions of as-cast and extruded ZK60-xGd （x=0-4） alloys were investigated. Meanwhile, the tensile mechanical property was tested. With increasing the Gd content, as-cast microstructure...Microstructures and phase compositions of as-cast and extruded ZK60-xGd （x=0-4） alloys were investigated. Meanwhile, the tensile mechanical property was tested. With increasing the Gd content, as-cast microstructure is refined gradually. Mg-Zn-Gd new phase increases gradually, while MgZn2 phase decreases gradually to disappear. The second phase tends to distribute along grain boundary by continuous network. As-cast tensile mechanical property is reduced slightly at ambient temperature when the Gd content does not exceed 2.98%. After extrusion by extrusion ratio of 40 and extrusion temperature of 593 K, microstructure is refined further with decreasing the average grain size to 2 μm for ZK60-2.98Gd alloy. Broken second phase distributes along the extrusion direction by zonal shape. Extruded tensile mechanical property is enhanced significantly. Tensile strength values at 298 and 473 K increase gradually from 355 and 120 MPa for ZK60 alloy to 380 and 164 MPa for ZK60-2.98Gd alloy, respectively. Extruded tensile fractures exhibit a typical character of ductile fracture.展开更多
The cold radial forging process usually introduces some changes of the material, such as the increased strength, the decreased plasticity and the introduction of anisotropic mechanical prop- erty. To obtain the change...The cold radial forging process usually introduces some changes of the material, such as the increased strength, the decreased plasticity and the introduction of anisotropic mechanical prop- erty. To obtain the changes of mechanical property of barrel processed by cold radial forging, the tangential mechanical properties of the barrel blank and the forged barrel are measured with a de- signed test based on the plastic deformation analysis for a barrel and by applying internal pressure, and their axial mechanical properties are measured by the tensile test. The changes of mechanical property of barrel processed by cold radial forging are obtained by comparing the mechanical proper- ties of the barrel blank and the forged barrel. The tangential and axial flow stresses of the barrel blank and the forged barrel are also presented.展开更多
The effect of heat treatment on microstructure and mechanical properties of the Ti-steel explosive-rolling clad plate was elaborated by optical microscopy （OM）, scanning electron microscopy （SEM）, X-ray diffracti...The effect of heat treatment on microstructure and mechanical properties of the Ti-steel explosive-rolling clad plate was elaborated by optical microscopy （OM）, scanning electron microscopy （SEM）, X-ray diffraction （XRD）, transmission electron microscopy （TEM）, micro-hardness test and shear test. The composites were subjected to heat treatment at temperature of 650-950 ~C for 60 min. The results show that the heat treatment process results in a great enhancement of diffusion and microstructural transformation. The shear strength decreases as the treatment temperature increases. Heated at 850 ℃ or below, their shear strength decreases slowly as a result of the formation of TiC in the diffusion interaction layer; while at the temperature of 850 ℃ or above, the shear strength decreases obviously, which is the consequence of a large amount of Ti-Fe intermetaUics （Fe2Ti/FeTi） along with some TiC distributing continuously at diffusion reaction layer.展开更多
The mixed grain structure and mechanical property anisotropy of AZ40 magnesium alloy bar with a diameter of 160 mm manufactured by ＂multi-direction forging（MDF） ＋ extrusion ＋ online cooling＂ technique were inves...The mixed grain structure and mechanical property anisotropy of AZ40 magnesium alloy bar with a diameter of 160 mm manufactured by ＂multi-direction forging（MDF） ＋ extrusion ＋ online cooling＂ technique were investigated by optical microscopy（OM）, scanning electron microscopy（SEM）, X-ray diffraction macro-texture measurement and room temperature（RT） tensile test. The results show that mixed grain structure is caused by the micro-segregation of Al in semi-continuous casting ingot. Homogenization of（380 °C, 8 h） ＋（410 °C, 12 h） cannot totally eliminate such micro-segregation. During MDF and extrusion, the dendrite interiors with 3%-4% Al（mass fraction） transform to fine grain zones, yet the dendrite edges with about 6% Al transform to coarse grain zones. XRD macro-textures of the outer, R/2 and center show typical fiber texture characteristics and the intensity of [0001]//Ra D orientation in the outer（11.245） is about twice as big as those in the R/2（6.026） and center（6.979）. The as-extruded AZ40 magnesium alloy bar has high elongation（A） and moderate ultimate tensile strength（Rm） in both extrusion direction（ED） and radius direction（Ra D）, i.e., A of 19%-25% and Rm of 256-264 MPa; however, yield strength（Rp0.2） shows anisotropy and heterogeneity, i.e., 103 MPa in Ra D, 137 MPa in ED-C（the center） and 161 MPa in ED-O（the outer）, which are mainly caused by the texture.（155 °C, 7 h） ＋（170 °C, 24 h） aging has no influence on strength and elongation of AZ40 magnesium bar.展开更多
The effects of addition of La on the microstructure of as-cast ADC12 A1-Alloy were investigated by using optical microscope （OM）, X-ray diffraction （XRD）, scanning electron microscope （SEM）, and energy disperse ...The effects of addition of La on the microstructure of as-cast ADC12 A1-Alloy were investigated by using optical microscope （OM）, X-ray diffraction （XRD）, scanning electron microscope （SEM）, and energy disperse spectroscopy （EDS）. The experimental results showed that the a-A1 and eutectic Si crystals were modified with the addition of 0.3 wt% La. The eutectic Si crystals showed a granular distribution. At the same time, the alloy possessed the best mechanical property. When more than 0.3 wt% La was added to ADC12 aluminum alloy, the microstructure of as-cast alloy was coarsening gradually with the increase of the content of La and the mechanical property decreased. The effect of rare earth La which was added in ADC 12 A1-Alloy for up to 0.9 wt% had been investigated in this study. The dendrites ofADC12 Al-alloy was refined obviously and the morphology of Si crystals showed a particle structure when the addition of La reached 0,3 wt%. Besides, the acicular La-rich intermetallics in the alloy deteriorated the mechanical property of alloy： To avoid this unwanted phase, the amount of added rare earth La must be less than 0.6 wt%.展开更多
基金National Natural Science Foundation of China(52275349)Key Research and Development Program of Shandong Province(2021ZLGX01)。
文摘Friction stir lap welding of AA2195 Al-Li alloy and Ti alloy was conducted to investigate the formation,microstructure,and mechanical properties of the joints.Results show that under different welding parameters,with the decrease in welding heat input,the weld surface is smoother.The Ti/Al joint interface is flat without obvious Ti and Al mixed structure,and the hook structure is not formed under optimal parameters.Due to the enhanced breaking effect of the stirring head,the hook structural defects and intermetallic compounds are more likely to form at the Ti/Al interface at high rotational speed of 1000 r/min,thereby deteriorating the mechanical properties of joints.Decreasing the heat input is beneficial to hardness enhancement of the aluminum alloy in the weld nugget zone.Under the optimal parameters of rotation speed of 800 r/min and welding speed of 120 mm/min,the maximum tensile shear strength of joint is 289 N/mm.
基金support by the National Natural Science Foundation of China(Grant Nos.U23A20546 and 52271010)the Chinese National Natural Science Fund for Distinguished Young Scholars(Grant No.52025015)the Natural Science Foundation of Tianjin City(No.21JCZDJC00510).
文摘1.Introduction The strength-ductility trade-offdilemma has long been a per-sistent challenge in Al matrix composites(AMCs)[1,2].This is-sue primarily arises from the agglomeration of reinforcements at the grain boundaries(GBs),which restricts local plastic flow dur-ing the plastic deformation and leads to stress concentration[3,4].Recently,the development of concepts aimed at achieving hetero-geneous grain has emerged as a promising approach for enhanc-ing comprehensive mechanical properties[5,6].
基金supported by the Key Research and Development Program of Shanxi Province(202102130501007)the Natural Science Foundation of Shanxi Province(202403021212109,202203021211173)the Scientific and Technological Innovation Programs of Higher Education Institutions in Shanxi(2024L039).
文摘Zinc(Zn)-based materials show broad application prospects for bone repair due to their biodegradability and good biocompatibility.In particular,Zn metal foam has unique interconnected pore structure that facilitates inward growth of new bone tissue,making it ideal candidates for orthopedic implants.However,pure Zn metal foam shows poor mechanical property,high degradation rate,and unsatisfactory osteogenic activity.Herein,Zinc-manganese(Zn-Mn)alloy foams were electrodeposited in Zn and Mn-containing electrolytes to overcome the concerns.The results showed that Mn could be incorporated into the foams in the form of MnZn_(13).Zn-Mn alloy foams showed better mechanical property and osteogenic activity as well as moderate degradation rate when compared with pure Zn metal foam.In addition,these properties could also be regulated by preparation process.The peak stress and osteogenic activity increased with deposition current(0.3‒0.5 A)and electrolyte pH(3‒5),but decreased with electrolyte temperature(20‒40℃),while the degradation rate exhibited opposite tendency,which suggests high deposition current and electrolyte pH and low electrolyte temperature can fabricate Zn-Mn alloy foam with favorable mechanical property,moderate degradation rate,and osteogenic activity.These findings provide a valuable reference for the design and fabrication of novel Zn-based biodegradable materials.
基金Funded by the National Natural Science Foundation of China(Nos.52171045,52162013,and 51932006)。
文摘The surface of MoSi2-SiB6/phenolic resin matrix composites was modified by mica,and the thermal oxidation behavior of the composites and the mechanical properties of the pyrolysis products were studied.The results showed that the mica improved the thermal properties of the composites,the thermal expansion coefficient decreased,and the liquid phase formation caused the composites to shrink and increase the density.The flexural strength of mica surface modified composites not only increased to 78.64MPa after thermal treatment at 800-1200℃,but reached 83.02 MPa after high temperature treatment at1400℃.The improvement of the mechanical properties of the residual product benefits from the formation of high temperature ceramic phases such as Mo_(2)C and MoB,and the improvement of the shear strength of the composites by the mica.The shear strength of MBm5-2 at room temperature reached 33.08 MPa,indicating that the improvement of the interlayer properties of the composites further improved its mechanical properties.
基金supported by the National Natural Science Foundation of China(No.52301041)the Guizhou Provincial Basic Research Program(No.QianKeHeJiChu-ZK[2024]YiBan036)+1 种基金the Special Fund for Special Posts of Guizhou University(No.[2023]26)the Fundamental Research Funds for the Central Universities.E.G.thanks support from Xiaomi Foundation.
文摘This study develops novel Mg-Sn-In-Ga alloys as potential implant materials for orthopedic applications.The corrosion behavior of the Mg-Sn-In-Ga alloys was studied through mass loss measurements,hydrogen evolution measurements,electrochemical analysis,and corrosion morphology observations.The results show that the corrosion rate of the Mg-1Sn-1In-1Ga alloy was only 0.10±0.003 mm/y after immersion in Hank’s solution for 15 days.This outstanding corrosion resistance was associated with the protective efect of the corrosion products.The increase in the Sn and Ga element content led to the precipitation of a large amount of Mg_(2)Sn and Mg_(5)Ga_(2),which had a dominant efect on the corrosion rate in the Mg-5Sn-1In-2Ga alloy.These precipitates increased the current density and detached from the alloy surface during the corrosion process.This can lead to a weakened protective efect of the corrosion layer,and thus generate localized corrosion and an increase in the corrosion rate.The strength of the Mg-5Sn-1In-2Ga alloy was enhanced due to fne-grain strengthening and precipitation strengthening.The ultimate tensile strength and yield strength of the Mg-5Sn-1In-2Ga alloy were~309 MPa and~253 MPa,respectively.
基金support of the National Natural Science Foundation of China(Grant Nos.52071191,52201077)the Natural Science Foundation of Shandong Province(Grant No.ZR2022QE191).
文摘Biomedical materials may suffer from stress-induced corrosion when performing as implant materials at load-bearing sites, bringing about variations in the microstructure, corrosion resistance, and mechanical properties. In this study, the corrosion behavior and mechanical properties of an extruded Mg-4Li-1Ca alloy were investigated under different micro-compressive stresses (0-6 MPa) using a novel homemade loading device. Under 0-3 MPa of micro-compressive stress, the strong basal texture of extruded Mg-4Li1Ca alloys was weakened and the internal stress gradient stimulated grain boundary migration to induce grain growth. Meanwhile, increased stress resulted in the precipitation of second-phase particles and the accumulation of residual stress, accelerating the corrosion rate due to preferential corrosion. However, with increasing stress, the volume fraction of the second phase increased, becoming the dominant factor controlling the corrosion rate, and residual stress was released for samples under 4.5-6 MPa of microcompressive stress. Hence, surface corrosion product films rapidly formed and served as effective physical barriers, weakening the microstructural effect on the corrosion behavior. The yield strength of Mg-4Li-1Ca alloy reached 95.48 MPa under 3 MPa of micro-compressive stress owing to the dual effects of precipitation strengthening and shear-band strengthening. The relationships between microstructure, corrosion behavior, and mechanical property provide a theoretical foundation for understanding the degradation characteristics of the Mg-4Li-1Ca alloy under physiological loading and practical application.
基金supported by the National Natural Science Foundation of China(Nos.51971021,52203382,and U1967212)the National Magnetic Confinement Fusion Program of China(Nos.2019YFE03120004 and 2019YFE03130002)the Natu-ral Science Basic Research Plan in Shaanxi Province of China(No.2022JQ-439).
文摘Dispersion-strengthened copper alloys can achieve ultra-high strength,but usually at the expense of duc-tility.In this study,a strategy for overcoming strength-ductility tradeoffof Cu alloys is realized through the introduction of bimodal grains structures.Cu-Ta alloys with only 0.5 at.%Ta content were successfully prepared by mechanical alloying combined with spark plasm sintering.The samples prepared by one-step and two-step ball milling methods are named as Cu-Ta(Ⅰ)and Cu-Ta(Ⅱ),respectively.The microstructural characterizations revealed that ultra-fine equiaxed grains with uniformly dispersed Ta precipitates were obtained in the Cu-Ta alloys.High strength of 377 MPa for yield strength together with elongation of∼8%was obtained in Cu-Ta(Ⅰ).Bimodal grains structures composed of fine-grain zones and coarse-grain zones were successfully introduced into Cu-Ta(Ⅱ)by a two-step ball milling approach,and both yield strength(463 MPa)and elongation(∼15%)were significantly synergistic enhanced.The hardness values of both Cu-Ta(Ⅰ)and Cu-Ta(Ⅱ)were almost kept nearly constant with the increase of annealing time,and the softening temperatures of Cu-Ta(Ⅰ)and Cu-Ta(Ⅱ)are 1018 and 1013℃,reaching 93.9%and 93.5%T m of pure Cu(1083℃),respectively.It reveals that the Cu-0.5 at.%Ta alloys exhibit excellent thermal stability and exceptional softening resistance.Ta nanoclusters with semi-coherent structures play an essential role in enhancing the strength and microstructural stability of alloys.Bimodal structures are beneficial to the activation of back stress strengthening and the initiation and propagation of microcracks,thus obtaining the extraordinary combination of strength and elongation.This study provides a new way to fabricate dispersion-strengthened Cu alloys with high strength,high elongation,excellent thermal stability and softening resistance,which have potential application value in the field of the future fusion reactor.
基金the National Natural Science Foundation of China(Grant Nos.52274398 and U22A20171)S&T Program of Hebei(Grant Nos.20311005D and 20591001D)the High Steel Center(HSC)at North China University of Technology and Yanshan University,China.
文摘The key role of oxide inclusions on the microstructure and mechanical property of a high-strength low-alloy steel was investigated.The field emission scanning electron microscope equipped with energy-dispersive spectrometry was used to characterize MnS precipitates.Oxide inclusions play an important role in the shape control of MnS precipitates.More oxides fovored to decrease the size and the aspect ratio of MnS precipitates.With less oxide inclusions in the steel,approximately over 16.7%MnS precipitates were with aspect ratio a>5 and pure MnS precipitates accounted for 75.9%in number.However,with more oxide inclusions in the steel,only 7.4%MnS precipitates were with a>5 and pure MnS precipitates accounted for 60.1%in number.Refinement of MnS by oxide inclusions improved the strength and inhibited the anisotropy.More oxide inclusions in the steel increased the yield strength and tensile strength of the steel in both longitudinal and transverse directions,and lowered the anisotropy of the mechanical property.
基金Project supported by the National Natural Science Foundation of China(U20A20274,52071158,51701085,U1664254)the Six Talents Peak Project of Jiangsu Province(2018-XCL-202)+1 种基金the Open Funds of SKLMMC of SJTU(MMC-KF18-16)the Jiangsu Province Key Laboratory of High-end Structural Materials(HSM1803,1902)。
文摘In this study, the in-situ synthesized ZrB_(2) nanoparticles and rare earth Sc were introduced to enhance the strength and ductility of 7N01 aluminum alloy, via the generation of high-melting and uniform nanodispersoids. The microstructure and mechanical property evolution of the prepared composites and the interaction between ZrB_(2) and Sc were studied in detail. The microstructure investigation shows that the introduction of rare earth scandium(Sc) can promote the distribution of ZrB_(2) nanoparticles, by improving their wettability to the Al melt. Meanwhile, the addition of rare earth Sc also modifies the coarse Al Zn Mg Mn Fe precipitated phases, refines the matrix grains and generates high-melting Al_3(Sc,Zr)/Al_3Sc nanodispersoids. Tensile tests of the composites show that with the combinatorial introduction of ZrB_(2) and Sc, the strength and ductility of the composites are improved simultaneously compared with the corresponding 7N01 alloy, ZrB_(2) /7N01 composite and Sc/7N01 alloy. And the optimum contents of ZrB_(2) and Sc are 3 wt% and 0.2 wt% in this study. The yield strength, ultimate strength and elongation of(3 wt% ZrB_(2) +0.2 wt% Sc)/7N01 composite are 477 MPa, 506 MPa and 9.8%, increased about 18.1%, 12.2%and 38% compared to 7N01 alloy. Furthermore, the cooperation strengthening mechanisms of ZrB_(2) and Sc are also discussed.
基金Funded by Joint Funds of the National Natural Science Foundation of China(No.U1904188)Jiangxi Provincial Department of Education Science and Technology Project(Nos.GJJ171079,GJJ181023 and GJJ181022)。
文摘Carbonated recycled powder as cementitious auxiliary material can reduce carbon emissions and realize high-quality recycling of recycled concrete.In this paper,microscopic property of recycled powder with three carbonation methods was tested through XRD and SEM,the mechanical property and microstructure of recycled powder mortar with three replacement rates were studied by ISO method and SEM,and the strengthening mechanism was analyzed.The results showed that the mechanical property of recycled powder mortar decreased with the increasing of replacement rate.It is suggested that the replacement rate of recycled powder should not exceed 20%.The strength index and activity index of carbonated recycled powder mortar were improved,in which the flexural strength was increased by 27.85%and compressive strength was increased by 20%at the maximum.Recycled powder can be quickly and completely carbonated,and the improvement effect of CH pre-soaking carbonation was the best.The activity index of carbonated recycled powder can meet the requirements of Grade II technical standard for recycled powder.Microscopic results revealed the activation mechanism of carbonated recycled powder such as surplus calcium source effect,alkaline polycondensation effect and carbonation enhancement effect.
基金supported by the National Natural Science Foundation of China (Grant Nos.51974058,52022017,52371005 and 51927801)the Fundamental Research Funds for the Central Universities.
文摘The semi-solid stir casting method is adopted to prepare 10 wt%SiC_(p)/Mg-6Zn-0.5Ca-xAl(x=0,1,3 and 5 wt%)composites,and the microstructure evolution and mechanical property of composites with various Al content are investigated.The results show that the addition of 3 wt%Al improves the distribution of SiC_(p),whereas the SiC_(p) cluster occurs again with Al content greater than 3%.An abnormal phenomenon of twinning is observed in the cast composites in this work.The SiC_(p)/Mg-6Zn-0.5Ca composite possesses the highest twin content of~23%,for which tension twins(TTW)and compression twins(CTW)account for~19%and~3%,respectively.The CTW is only observed in ZXA600 composite.The addition of Al has an inhibiting effect for the generation and growth of twins.The content of twin decreases firstly and then increases with increase of Al content.The lowest twin content is obtained as Al increases to 3 wt%.It is found the existence of twin is detrimental to the mechanical property of composites.As-cast SiC_(p)/Mg-6Zn-0.5Ca-3Al composite with the lowest twin content exhibits the optimal mechanical property of yield strength,ultimate tensile strength and elongation for 100 MPa,188 MPa and 4.4%,respectively.The outstanding mechanical property is attributed to the uniform distribution of SiC_(p),the low twin content and the well-distributed fine second phases.
基金supported by the National Key Research and Development Program of China(No.2021YFB3701000)the National Natural Science Foundation of China(Nos.U2167213,51971053)+1 种基金H.C.Pan acknowledges the financial assistance from the Young Elite Scientists Sponsorship Program by China Association for Science and Technology(2019-2021QNRC001-003)the fund from the Fundamental Research Funds for the Central Universities(N2202020).
文摘In this work,the microstructure and mechanical properties of large cross-sectioned Mg-9Gd-3Y-1.2Zn-0.5Zr(VWZ931)samples produced by the small extrusion ratio has been investigated.The as-extruded VWZ931 sample with diameter of~30 mm can exhibit the high yield strength(YS)of 339 MPa,ultimate tensile strength(UTS)of 387 MPa and elongation of 8.2%,respectively.After peak-aged,the YS and UTS of the Mg samples were significantly increased to 435 MPa and 467 MPa.The small extrusion ratio leads to the low fraction of dynamic recrystallized(DRX)grains in VWZ931 sample,and the texture hardening effect can be fully utilized to achieve high strength.The combined effect of precipitation strengthening due to the long-period stacking ordered phases and theβ′phase,grain boundary strengthening due to the fine DRX grains,heterogeneous deformation-induced strengthening caused by bimodal microstructure,can together contribute to the high strength of present Mg alloy.The findings can shed light on designing other large-sized Mg wrought alloys with high mechanical performance.
基金Enterprise Research and Development Project of Beijing Lirr High-Temperature Materials Co.,Ltd.(2020-02)Key Scientific Research Project for Universities and Colleges in Henan Province(19A430028)+1 种基金the Excellent Youth Research Project of Anhui Province(2022AH030135)the PhD Research Funding of Suzhou University(2021BSK041).
文摘Conventional MgO-C bricks(graphite content>14 wt.%)produce a great deal of greenhouse gas emission,while low-carbon MgO-C bricks have serious thermal shock resistance during high-temperature service.To enhance the high-temperature mechanical property and thermal shock resistance of low-carbon MgO-C bricks,a novel route of introducing ZrSiO_(4) powder into low-carbon MgO-C bricks was reported in such refractories with 2 wt.% flaky graphite.The results indicate that the low-carbon MgO-C brick with 0.5 wt.%ZrSiO_(4) addition has the maximum hot modulus of rupture at 1400℃ and the corresponding specimen fired in the carbon embedded atmosphere has the maximum residual strength ratio(98.6%)after three thermal shock cycles.It is found that some needle-like AlON and plate-like Al_(2)O_(3)-ZrO_(2) composites were in situ formed in the matrices after the low-carbon MgO-C bricks were coked at 1400℃,which can enhance the high-temperature mechanical property and thermal shock resistance due to the effect of fiber toughening and particle toughening.Moreover,CO_(2) emission of the newly developed low-carbon MgO-C bricks is reduced by 58.3% per ton steel after using them as the working lining of a 90 t vacuum oxygen decarburization ladle.
基金the support of the Key Program of National Natural Science Foundation of China(Grant No.52235005)the Natural Science Foundation of Hunan Province,China(Grant No.2023JJ30137).
文摘Owing to the special layer-by-layer deposition process of directed energy deposition(DED),columnar coarse grains,produced by cyclic reheating with intrinsic directional heat flow along the building direc-tion,are difficult to avoid.These grains result in strong anisotropic characteristics with poor mechanical properties,which restrict the application of DED products.This work proposes a novel fabrication strat-egy based on the cyclic-phase-transformation behavior,which can reduce the anisotropy and improve the mechanical properties of DED-printed stainless steel.Using this fabrication strategy,316 L powder(austenitic stainless steel)and 17-4PH powder(martensitic stainless steel)were mixed in different mass ratios to fabricate five types of DED-printed stainless steels.Among the five samples,P70(mixture of 70 wt%17-4PH powder and 30 wt%316 L powder)showed the weakest anisotropy and the best mechanical properties,which can be attributed to the cyclic phase transformation under cyclic reheating treatment and the transformation-induced plasticity(TRIP)effect over a wide range of strains,respectively.Com-pared with the pure 316 L printed material,the tensile test results of P70 showed that the yield strength(YS)and ultimate tensile strength(UTS)increased by 35.4%and 34.5%,respectively,whereas the uniform elongation(UE)and total elongation(TE)were improved by 63.9%and 31.4%,respectively.In addition,the strength-ductility balance(UTS×UE)increased by as much as 120.4%.The proposed fabrication strategy is expected to reduce the anisotropy in other materials that undergo cyclic-phase-transformation phe-nomena during additive manufacturing.
基金Projects(50674038,50974048)supported by the National Natural Science Foundation of ChinaProject(200802140004)supported by Doctoral Fund of Ministry of Education of China
文摘Low temperature mechanical properties of AZ91D magnesium alloy fabricated by solid recycling process from recycled scraps were studied. Various microstructural analyses were performed using optical microscopy （OM） and scanning electron microscopy （SEM）. The recycled specimens consist of fine grains due to dynamic recrystallization and the interfaces of original individual scraps are not identified. Tensile tests were performed at a strain rate of 5 x 10 3 s 1 at room temperature （27 ~C）, -70, -100 and 130 ~C, respectively. Ultimate tensile strength of the specimens increases slightly with decreasing the tensile temperature, and elongation to failure decreases with decreasing the tensile temperature. The tensile specimens at -130 ~C show the highest ultimate tensile strength of 360.65 MPa and the lowest elongation to failure of 5.46%. Impact tests were performed at room temperature （27 ~C）, -70 and -130 ~C, respectively. Impact toughness decreases with decreasing the impact temperature. The impact specimens at -130 ~C show the lowest impact toughness of 3.06 J/cm2.
基金Projects(2010A090200078,2011A080403008)supported by the Major Science and Technology Project of Guangdong Province,China
文摘Microstructures and phase compositions of as-cast and extruded ZK60-xGd （x=0-4） alloys were investigated. Meanwhile, the tensile mechanical property was tested. With increasing the Gd content, as-cast microstructure is refined gradually. Mg-Zn-Gd new phase increases gradually, while MgZn2 phase decreases gradually to disappear. The second phase tends to distribute along grain boundary by continuous network. As-cast tensile mechanical property is reduced slightly at ambient temperature when the Gd content does not exceed 2.98%. After extrusion by extrusion ratio of 40 and extrusion temperature of 593 K, microstructure is refined further with decreasing the average grain size to 2 μm for ZK60-2.98Gd alloy. Broken second phase distributes along the extrusion direction by zonal shape. Extruded tensile mechanical property is enhanced significantly. Tensile strength values at 298 and 473 K increase gradually from 355 and 120 MPa for ZK60 alloy to 380 and 164 MPa for ZK60-2.98Gd alloy, respectively. Extruded tensile fractures exhibit a typical character of ductile fracture.
文摘The cold radial forging process usually introduces some changes of the material, such as the increased strength, the decreased plasticity and the introduction of anisotropic mechanical prop- erty. To obtain the changes of mechanical property of barrel processed by cold radial forging, the tangential mechanical properties of the barrel blank and the forged barrel are measured with a de- signed test based on the plastic deformation analysis for a barrel and by applying internal pressure, and their axial mechanical properties are measured by the tensile test. The changes of mechanical property of barrel processed by cold radial forging are obtained by comparing the mechanical proper- ties of the barrel blank and the forged barrel. The tangential and axial flow stresses of the barrel blank and the forged barrel are also presented.
文摘The effect of heat treatment on microstructure and mechanical properties of the Ti-steel explosive-rolling clad plate was elaborated by optical microscopy （OM）, scanning electron microscopy （SEM）, X-ray diffraction （XRD）, transmission electron microscopy （TEM）, micro-hardness test and shear test. The composites were subjected to heat treatment at temperature of 650-950 ~C for 60 min. The results show that the heat treatment process results in a great enhancement of diffusion and microstructural transformation. The shear strength decreases as the treatment temperature increases. Heated at 850 ℃ or below, their shear strength decreases slowly as a result of the formation of TiC in the diffusion interaction layer; while at the temperature of 850 ℃ or above, the shear strength decreases obviously, which is the consequence of a large amount of Ti-Fe intermetaUics （Fe2Ti/FeTi） along with some TiC distributing continuously at diffusion reaction layer.
基金Project(2013CB632202)supported by the National Basic Research Program of China
文摘The mixed grain structure and mechanical property anisotropy of AZ40 magnesium alloy bar with a diameter of 160 mm manufactured by ＂multi-direction forging（MDF） ＋ extrusion ＋ online cooling＂ technique were investigated by optical microscopy（OM）, scanning electron microscopy（SEM）, X-ray diffraction macro-texture measurement and room temperature（RT） tensile test. The results show that mixed grain structure is caused by the micro-segregation of Al in semi-continuous casting ingot. Homogenization of（380 °C, 8 h） ＋（410 °C, 12 h） cannot totally eliminate such micro-segregation. During MDF and extrusion, the dendrite interiors with 3%-4% Al（mass fraction） transform to fine grain zones, yet the dendrite edges with about 6% Al transform to coarse grain zones. XRD macro-textures of the outer, R/2 and center show typical fiber texture characteristics and the intensity of [0001]//Ra D orientation in the outer（11.245） is about twice as big as those in the R/2（6.026） and center（6.979）. The as-extruded AZ40 magnesium alloy bar has high elongation（A） and moderate ultimate tensile strength（Rm） in both extrusion direction（ED） and radius direction（Ra D）, i.e., A of 19%-25% and Rm of 256-264 MPa; however, yield strength（Rp0.2） shows anisotropy and heterogeneity, i.e., 103 MPa in Ra D, 137 MPa in ED-C（the center） and 161 MPa in ED-O（the outer）, which are mainly caused by the texture.（155 °C, 7 h） ＋（170 °C, 24 h） aging has no influence on strength and elongation of AZ40 magnesium bar.
基金Supported by the National Natural Science Foundation of China(No.51165032)the Innovative Group of Science and Technology of College of Jiangxi Province(No.00008713)
文摘The effects of addition of La on the microstructure of as-cast ADC12 A1-Alloy were investigated by using optical microscope （OM）, X-ray diffraction （XRD）, scanning electron microscope （SEM）, and energy disperse spectroscopy （EDS）. The experimental results showed that the a-A1 and eutectic Si crystals were modified with the addition of 0.3 wt% La. The eutectic Si crystals showed a granular distribution. At the same time, the alloy possessed the best mechanical property. When more than 0.3 wt% La was added to ADC12 aluminum alloy, the microstructure of as-cast alloy was coarsening gradually with the increase of the content of La and the mechanical property decreased. The effect of rare earth La which was added in ADC 12 A1-Alloy for up to 0.9 wt% had been investigated in this study. The dendrites ofADC12 Al-alloy was refined obviously and the morphology of Si crystals showed a particle structure when the addition of La reached 0,3 wt%. Besides, the acicular La-rich intermetallics in the alloy deteriorated the mechanical property of alloy： To avoid this unwanted phase, the amount of added rare earth La must be less than 0.6 wt%.
