With the increase of gray scale and flat panel display （FPD） size, subspace bitwise scanning strategy can be replaced traditional scanning method to cut down frame frequency. However, the direct searching strategy ...With the increase of gray scale and flat panel display （FPD） size, subspace bitwise scanning strategy can be replaced traditional scanning method to cut down frame frequency. However, the direct searching strategy （DSS） becomes unfeasible to obtain corresponding high gray scale scanning matrix. Thus, particle swarm optimization （PSO） is introduced to accelerate searching for high gray scale weights scanning matrix （WSM） with its parallelism and global optimization feature. Finally a WSM of 256 gray scales is found out successfully with Matlab, which both gray linearity and scanning efficiency are satisfied.展开更多
This paper discusses a kind of optimal method used for searching flat panel display （FPD） scanning matrix. The method adopts bionic algorithm： genetic algorithm （GA） and particle swarm optimization （PSO） algori...This paper discusses a kind of optimal method used for searching flat panel display （FPD） scanning matrix. The method adopts bionic algorithm： genetic algorithm （GA） and particle swarm optimization （PSO） algorithm. The method using single GA is more time-consuming, and the search efficiency is low in later evolution; the PSO algorithm is easily falling into the local optimal solution and appears the premature convergent phenomenon. Hence, a hybrid approach of GAPSO is found to optimize the search for high grayscale weights scanning matrix. Finally in the acceptable time, it finds a weight scanning matrix （WSM） of 256 gray scales with Matlab, whose scanning efficiency reaches 94.73% and the linearity is very good.展开更多
The status and the variation of electrical resistance of impacted carbon fiber/epoxy-matrix composites were studied by ultrasonic F-scan and electrical resistance measurement The experimental results shows that impact...The status and the variation of electrical resistance of impacted carbon fiber/epoxy-matrix composites were studied by ultrasonic F-scan and electrical resistance measurement The experimental results shows that impact damage energy threshold value of carbon fabric/epoxy-matrix composites can determine by using ultrasonic F-scan. When the impact energy exceeds the threshold value, damage is generated in composites. Electrical resistance of impacted composites is changed owing to the contact of each carbon fiber unit in composites, which cause a change of the series-parallel in conductors. The veracity of detecting impact damage in composites can be improved in this case.展开更多
AlO-SiOshort fiber/Al-Cu-Mg matrix composites containing different Mg contents were fabricated using squeeze casting method.Differential scanning calorimeter(DSC) was used to investigate the reaction condition of the ...AlO-SiOshort fiber/Al-Cu-Mg matrix composites containing different Mg contents were fabricated using squeeze casting method.Differential scanning calorimeter(DSC) was used to investigate the reaction condition of the composites with different Mg contents.The microstructure of the composites was observed by transmission electron microscopy(TEM).The experimental results show that the Mg content added to the 2024Al matrix significantly affects interfacial condition between Al2O3-SiO2 short fiber and aluminum matrix.At the temperature above 538 ℃,Al2O3-SiO2 short fiber is prone to react with Mg and forms MgAl2O4 reaction product when Mg content added to aluminum matrix is above 1.0wt%.展开更多
The differential scanning calorimetric(DSC) and transmission electron microanalysis (TEM) techniques were used to study the kinetic process of precipitation in matrix of cast SiC_p/2024 composites.The results showed t...The differential scanning calorimetric(DSC) and transmission electron microanalysis (TEM) techniques were used to study the kinetic process of precipitation in matrix of cast SiC_p/2024 composites.The results showed that precipitation reactions of GP zone and intermediate phase S'(Al_2CuMg)in the composites were accelerated compared with SiC-free material,the peak temperatures of both reactions were decreased.The reaction enthalpies of both the GP zone and intermediate phase S' formation in the matrix were substantially decreased after the addition of SiC.TEM analysis found that the alloying element Mg segregated at the SiC/Al interfaces,and was depleted in the matrix near the interface.The precipitation-free zones(PFZ) and precipitation-sparse zones(PSZ) formed near the interfaces,as a results,the volume fraction of precipitates in matrix was reduced.展开更多
SiC particulates reinforced alumina matrix composites were fabricated using Directed Metal Oxidation (DIMOX) process. Continuous oxidation of an Al-Si-Mg-Zn alloy with different interlayers (dopents) as growth promote...SiC particulates reinforced alumina matrix composites were fabricated using Directed Metal Oxidation (DIMOX) process. Continuous oxidation of an Al-Si-Mg-Zn alloy with different interlayers (dopents) as growth promoters, will encompasses the early heating of the alloy ingot, melting and continued heating to temperature in the narrow range of 950°C to 980°C in an atmosphere of oxygen. Varying interlayers (dopents) are incorporated to examine the growth conditions of the composite materials and to identification of suitable growth promoter. The process is extremely difficult because molten aluminum does not oxidize after prolonged duration at high temperatures due to the formation of a passivating oxide layer. It is known that the Lanxide Corporation had used a combination of dopents to cause the growth of alumina from molten metal. This growth was directed, i.e. the growth is allowed only in the required direction and restricted in the other directions. The react nature of the dopants was a trade secret. Though it is roughly known that Mg and Si in the Al melt can aid growth, additional dopents used, the temperatures at which the process was carried out, the experimental configurations that aided directed growth were not precisely known. In this paper we have evaluated the conditions in which composites can be grown in large enough sizes for evaluation application and have arrived at a procedure that enables the fabrication of large composite samples by determining the suitable growth promoter (dopant). Scanning electron microscopic, EDS analysis of the composite was found to contain a continuous network of Al2O3, which was predominantly free of grain-boundary phases, a continuous network of Al alloy. Fabrication of large enough samples was done only by the inventor company and the property measurements by the company were confirmed to those needed to enable immediate applications. Since there are a large number of variable affecting robust growth of the composite, fabrication large sized samples for measurements is a difficult task. In the present work, to identify a suitable window of parameters that enables robust growth of the composite has been attempted.展开更多
Titanium matrix composites reinforced with a-Al2O3 and TiB2 particles were fabricated by in situ synthesis from a Ti-Al-B2O3 system. The reaction processes and microstructure were analyzed by using differential scanni...Titanium matrix composites reinforced with a-Al2O3 and TiB2 particles were fabricated by in situ synthesis from a Ti-Al-B2O3 system. The reaction processes and microstructure were analyzed by using differential scanning calorimetry（DSC）, scanning electron microscopy（SEM） and X-ray diffraction（XRD）. The results showed that the reactions in the Ti-Al-B2O3 system can occur spontaneously and consist of three steps： 1） 15 Al ＋ 7B2O3 → 7α-Al2O3 ＋ AlB12 ＋ 2B; 2） 14 B ＋ 2Al → AlB12 ＋ AlB2 and 3） 7Ti ＋ AlB（12） ＋ AlB2 → 7TiB2 ＋ 2Al. The final reinforcements were composed of α-Al2O3 and TiB2 particles, which were uniformly distributed in the titanium matrix.展开更多
In this paper, a micro-mechanical model is implemented in software for the prediction of local mechanical properties of discontinuous short fiber reinforced composites. The model, based on the Mori and Tanaka method, ...In this paper, a micro-mechanical model is implemented in software for the prediction of local mechanical properties of discontinuous short fiber reinforced composites. The model, based on the Mori and Tanaka method, shear-lag, computational model, Nielsen-Chen model and Miwa’s model is used to predict the elastic behaviour of basalt short fiber reinforced with Al alloy composites. The Al/basalt Metal Matrix Composites (MMCs) contain basalt short fiber from 2.5% to 10% in steps of 2.5 wt.% and are fabricated using squeeze infiltration technique. The effects of fiber length and orientation on elastic properties of Al/basalt MMCs are investigated. A comparison between the experimental data and the theoretical data based on physical models is made, and the significance of the findings is discussed. The results show that as short basalt fiber content was increased from 2.5% to 10% by wt.%, an improvement in Young’s modulus of 13.26% has been observed. Optical microscopy was used to examine the general microstructure and fiber distribution in the composite produced. Scanning Electron Microscopy (SEM) was performed on the fractured surface to understand the failure mechanisms.展开更多
基金supported by the Shanghai University Innovation Fundation (Grant No.SHUCX102370)
文摘With the increase of gray scale and flat panel display （FPD） size, subspace bitwise scanning strategy can be replaced traditional scanning method to cut down frame frequency. However, the direct searching strategy （DSS） becomes unfeasible to obtain corresponding high gray scale scanning matrix. Thus, particle swarm optimization （PSO） is introduced to accelerate searching for high gray scale weights scanning matrix （WSM） with its parallelism and global optimization feature. Finally a WSM of 256 gray scales is found out successfully with Matlab, which both gray linearity and scanning efficiency are satisfied.
基金supported by the Innovation Foundation of Shanghai University(Grant No.SHUCX112371)
文摘This paper discusses a kind of optimal method used for searching flat panel display （FPD） scanning matrix. The method adopts bionic algorithm： genetic algorithm （GA） and particle swarm optimization （PSO） algorithm. The method using single GA is more time-consuming, and the search efficiency is low in later evolution; the PSO algorithm is easily falling into the local optimal solution and appears the premature convergent phenomenon. Hence, a hybrid approach of GAPSO is found to optimize the search for high grayscale weights scanning matrix. Finally in the acceptable time, it finds a weight scanning matrix （WSM） of 256 gray scales with Matlab, whose scanning efficiency reaches 94.73% and the linearity is very good.
基金Funded by the Key Laboratory of Nondestructive Testing (Nanchang Hangkong University), Ministry of Education, China(No.ZD200829001)
文摘The status and the variation of electrical resistance of impacted carbon fiber/epoxy-matrix composites were studied by ultrasonic F-scan and electrical resistance measurement The experimental results shows that impact damage energy threshold value of carbon fabric/epoxy-matrix composites can determine by using ultrasonic F-scan. When the impact energy exceeds the threshold value, damage is generated in composites. Electrical resistance of impacted composites is changed owing to the contact of each carbon fiber unit in composites, which cause a change of the series-parallel in conductors. The veracity of detecting impact damage in composites can be improved in this case.
基金This work is financially supported by Harbin Youth Fund( NoDCQQ24405206)
文摘AlO-SiOshort fiber/Al-Cu-Mg matrix composites containing different Mg contents were fabricated using squeeze casting method.Differential scanning calorimeter(DSC) was used to investigate the reaction condition of the composites with different Mg contents.The microstructure of the composites was observed by transmission electron microscopy(TEM).The experimental results show that the Mg content added to the 2024Al matrix significantly affects interfacial condition between Al2O3-SiO2 short fiber and aluminum matrix.At the temperature above 538 ℃,Al2O3-SiO2 short fiber is prone to react with Mg and forms MgAl2O4 reaction product when Mg content added to aluminum matrix is above 1.0wt%.
文摘The differential scanning calorimetric(DSC) and transmission electron microanalysis (TEM) techniques were used to study the kinetic process of precipitation in matrix of cast SiC_p/2024 composites.The results showed that precipitation reactions of GP zone and intermediate phase S'(Al_2CuMg)in the composites were accelerated compared with SiC-free material,the peak temperatures of both reactions were decreased.The reaction enthalpies of both the GP zone and intermediate phase S' formation in the matrix were substantially decreased after the addition of SiC.TEM analysis found that the alloying element Mg segregated at the SiC/Al interfaces,and was depleted in the matrix near the interface.The precipitation-free zones(PFZ) and precipitation-sparse zones(PSZ) formed near the interfaces,as a results,the volume fraction of precipitates in matrix was reduced.
文摘SiC particulates reinforced alumina matrix composites were fabricated using Directed Metal Oxidation (DIMOX) process. Continuous oxidation of an Al-Si-Mg-Zn alloy with different interlayers (dopents) as growth promoters, will encompasses the early heating of the alloy ingot, melting and continued heating to temperature in the narrow range of 950°C to 980°C in an atmosphere of oxygen. Varying interlayers (dopents) are incorporated to examine the growth conditions of the composite materials and to identification of suitable growth promoter. The process is extremely difficult because molten aluminum does not oxidize after prolonged duration at high temperatures due to the formation of a passivating oxide layer. It is known that the Lanxide Corporation had used a combination of dopents to cause the growth of alumina from molten metal. This growth was directed, i.e. the growth is allowed only in the required direction and restricted in the other directions. The react nature of the dopants was a trade secret. Though it is roughly known that Mg and Si in the Al melt can aid growth, additional dopents used, the temperatures at which the process was carried out, the experimental configurations that aided directed growth were not precisely known. In this paper we have evaluated the conditions in which composites can be grown in large enough sizes for evaluation application and have arrived at a procedure that enables the fabrication of large composite samples by determining the suitable growth promoter (dopant). Scanning electron microscopic, EDS analysis of the composite was found to contain a continuous network of Al2O3, which was predominantly free of grain-boundary phases, a continuous network of Al alloy. Fabrication of large enough samples was done only by the inventor company and the property measurements by the company were confirmed to those needed to enable immediate applications. Since there are a large number of variable affecting robust growth of the composite, fabrication large sized samples for measurements is a difficult task. In the present work, to identify a suitable window of parameters that enables robust growth of the composite has been attempted.
基金Funded by National Natural Science Foundation of China(Nos.51571118 and 51371098)Natural Science Foundation of Jiangsu Province(No.BK20141308)
文摘Titanium matrix composites reinforced with a-Al2O3 and TiB2 particles were fabricated by in situ synthesis from a Ti-Al-B2O3 system. The reaction processes and microstructure were analyzed by using differential scanning calorimetry（DSC）, scanning electron microscopy（SEM） and X-ray diffraction（XRD）. The results showed that the reactions in the Ti-Al-B2O3 system can occur spontaneously and consist of three steps： 1） 15 Al ＋ 7B2O3 → 7α-Al2O3 ＋ AlB12 ＋ 2B; 2） 14 B ＋ 2Al → AlB12 ＋ AlB2 and 3） 7Ti ＋ AlB（12） ＋ AlB2 → 7TiB2 ＋ 2Al. The final reinforcements were composed of α-Al2O3 and TiB2 particles, which were uniformly distributed in the titanium matrix.
文摘In this paper, a micro-mechanical model is implemented in software for the prediction of local mechanical properties of discontinuous short fiber reinforced composites. The model, based on the Mori and Tanaka method, shear-lag, computational model, Nielsen-Chen model and Miwa’s model is used to predict the elastic behaviour of basalt short fiber reinforced with Al alloy composites. The Al/basalt Metal Matrix Composites (MMCs) contain basalt short fiber from 2.5% to 10% in steps of 2.5 wt.% and are fabricated using squeeze infiltration technique. The effects of fiber length and orientation on elastic properties of Al/basalt MMCs are investigated. A comparison between the experimental data and the theoretical data based on physical models is made, and the significance of the findings is discussed. The results show that as short basalt fiber content was increased from 2.5% to 10% by wt.%, an improvement in Young’s modulus of 13.26% has been observed. Optical microscopy was used to examine the general microstructure and fiber distribution in the composite produced. Scanning Electron Microscopy (SEM) was performed on the fractured surface to understand the failure mechanisms.
