Based on the equivalent circuit model of a two-port optical receiver front-end,the relationship between the equivalent input noise current spectral density and the noise figure is analyzed. The derived relationship ha...Based on the equivalent circuit model of a two-port optical receiver front-end,the relationship between the equivalent input noise current spectral density and the noise figure is analyzed. The derived relationship has universal validity for determining the equivalent input noise current spectral density for optical receiver designs, as verified by measuring a 155Mb/s high-impedance optical receiver front.end. Good agreement between calculated and simulated results has been achieved.展开更多
The high corrosion resistance of duplex stainless steel （DSS） is due to elements such as Cr, Mo and N, hut also depends on the microstructure. The best general properties are obtained with approximately equal amount...The high corrosion resistance of duplex stainless steel （DSS） is due to elements such as Cr, Mo and N, hut also depends on the microstructure. The best general properties are obtained with approximately equal amounts of austenite and ferrite and the absence of third phases such as σ（sigma） and Cr2N. In the present work the effect of heat input variations on the microstructure and corrosion resistance of a DSS UNS S32760 in artificial sea water media were studied. The corrosion resistance in 3.5 % of NaCl solution was evaluated by potentiostatic polarization tests at room temperature. It is found that the presence of sigma phase and Cr2N decreases the corrosion potential. The specimen with heat input of approximately 0.95 kJ/mm have the best corrosion characteristics, which is the result for the lack of deleterious phases such as sigma and Cr2 N and balanced ferrite austenite proportion.展开更多
Based on the data and method offered by Liu et al. （2009）, the direct wind and Stokes drift-induced energy inputs into the Ekman layer within the Antarctic Circumpolar Current （ACC） area are reestimated since the ...Based on the data and method offered by Liu et al. （2009）, the direct wind and Stokes drift-induced energy inputs into the Ekman layer within the Antarctic Circumpolar Current （ACC） area are reestimated since the results of the former have been proved to be underestimated. And the result shows that the total rate of energy input into the Ekman-Stokes layer within the ACC area is 852.41 GW, including 649.75 GW of direct wind energy input （76%） and 202.66 GW of Stoke drift-induced energy input （24%）. Total increased energy input, due to wave-induced Coriolis-Stokes forcing added to the classical Ekman model, is 52.05 GW, accounting for 6.5% of the wind energy input into the classical Ekman layer. The long-term variability of direct wind and Stokes drift-induced energy inputs into the Ekman layer within the ACC is also investigated, and the result shows that the Stokes drift hinders the decadal increasing trend of direct wind energy input. Meanwhile, there is a period of 4-5 a in the energy spectrums, as same as the Antarctic circumpolar wave.展开更多
In this paper, by change of integration path in complex spectrum domain and by defining input admittance as the ratio of complex radiated power to amplitude of square of voltage across the gap, new expressions of admi...In this paper, by change of integration path in complex spectrum domain and by defining input admittance as the ratio of complex radiated power to amplitude of square of voltage across the gap, new expressions of admittance (valid for all frequencies ) of infinitely long cylindrical antenna with and without conducting ground are obtained. Meanwhile corresponding formulas of current distribution are derived in detail. Some numerical computations are also given.展开更多
The effects of different wind input and wave dissipation formulations on the steady Ekman current solution are described. Two formulations are considered: one from the wave modeling(WAM) program proposed by Hasselmann...The effects of different wind input and wave dissipation formulations on the steady Ekman current solution are described. Two formulations are considered: one from the wave modeling(WAM) program proposed by Hasselmann and Komen and the other provided by Tsagareli and Babanin. The solution adopted for our study was presented by Song for the wave-modifi ed Ekman current model that included the Stokes drift, wind input, and wave dissipation with eddy viscosity increasing linearly with depth. Using the Combi spectrum with tail effects, the solutions are calculated using two formulations for wind input and wave dissipation, and compared. Differences in the results are not negligible. Furthermore, the solution presented by Song and Xu for the eddy viscosity formulated using the K-Profi le Parameterization scheme under wind input and wave dissipation given by Tsagareli and Babanin is compared with that obtained for a depth-dependent eddy viscosity. The solutions are further compared with the available well-known observational data. The result indicates that the Tsagareli and Babanin scheme is more suitable for use in the model when capillary waves are included, and the solution calculated using the K-Profi le Parameterization scheme agrees best with observations.展开更多
Single-phase,non-isolated microinverters used in photovoltaic(PV)systems commonly encounter two persistent challenges:High-frequency leakage current and fluctuating power delivery.This paper presents a novel single-ph...Single-phase,non-isolated microinverters used in photovoltaic(PV)systems commonly encounter two persistent challenges:High-frequency leakage current and fluctuating power delivery.This paper presents a novel single-phase,non-isolated,multi-input microinverter topology with a common-ground structure that effectively eliminates ground leakage current without requiring additional active components.The proposed microinverter architecture integrates a dual-boost configuration and uses only four active switches.This is especially advantageous in terms of the component count,which is beneficial to enhance reliability,reduce cost,and simplify the overall system design.With one,two,or four PV inputs,it can operate without interruption under unbalanced voltage or partial shading and even if some inputs drop to zero.A tailored modulation scheme minimizes conduction losses while maintaining a stable direct-current(DC)-link voltage,and a decoupling capacitor efficiently absorbs the single-phase pulsating power,thus overcoming one major limitation in existing microinverter designs.By validating with a 1-kW GaN-based prototype,both the simulated and experimental results demonstrate its high efficiency,robustness,and practical suitability for cost-effective PV applications,with a peak efficiency value of 94.8%.展开更多
The concept of connecting two boost half bridge DC-DC converter modules in input-paral- lel output-parallel configuration is presented. The input-parallel-output-parallel （IPOP） converter consists of multiple boost ...The concept of connecting two boost half bridge DC-DC converter modules in input-paral- lel output-parallel configuration is presented. The input-parallel-output-parallel （IPOP） converter consists of multiple boost half bridge （BHB） DC-DC converter modules which are connected in par- allel at the input and output side. This kind of converter is an attractive solution for high power ap- plications. The correlation between input current sharing （ICS） and output current sharing （OCS） of the IPOP converter basic modules is described. Two loop control strategies, consisting of input cur- rent loop and output voltage loop, have been developed to achieve equal ICS and OCS in this present work. The control strategy for the IPOP configuration of boost haft bridge DC-DC converter has been verified for different load conditions （half load and full load）, The IPOP system proposed here is comprising of two modules but it can be extended to three or more. The performance of the pro- posed system along with the control strategy is verified by simulation in MATLAB using Simpower tool. Finally the satisfactory simulation results are obtained.展开更多
Multi-modular system plays an important role in power system architecture because low voltage and low power converters can be connected in any combination parallel or series at input/ output side in order to obtained ...Multi-modular system plays an important role in power system architecture because low voltage and low power converters can be connected in any combination parallel or series at input/ output side in order to obtained any given power system specifications. Multi-modular boost haft bridge DC-DC converter in the configuration of input series output parallel has been investigated in this paper. The boost half bridge DC-DC converters are connected in input series output parallel con- figuration in order to achieve equal input voltage sharing and output current sharing between the con- verters. This can be achieved with the help of dynamic control scheme which consists of two loops, a voltage loop and a current loop, for each module. Dynamic behavior of multi-modular converter configuration has been observe by varying the load condition. Moreover, the results obtained through multi-modular converter describe that the system has good dynamic and steady state response. Al- though two converter modules are focused in this paper but it can be modified to any number of modules.展开更多
This paper presents an efficient supply current wave shaping technique for bridgeless interleaved Single Ended Primary Inductor Converter(SEPIC).The SEPIC converter converts an Alternating Current(AC)to Direct Current...This paper presents an efficient supply current wave shaping technique for bridgeless interleaved Single Ended Primary Inductor Converter(SEPIC).The SEPIC converter converts an Alternating Current(AC)to Direct Current(DC)with the boost converter.Power Factor Correction(PFC)is progressively significant to achieve high energy efficiency.The overall system efficiency can be increased as the bridgeless topology has less conduction losses from rectifying bridges.Also,the bridgeless and interleaved techniques are incorporated in this study to achieve better performance.The performance of the system is analyzed on both current control and sensor-less techniques.Different controllers such as Proportional Integral(PI)control,peak current control,Non-Linear Carrier(NLC)control,and sensor-less current control are integrated.All the above controllers are implemented using MATrix LABoratory(MATLAB)/SIMULINK.The performance parameter,namely Power Factor(PF),Total Harmonic Distortion(THD),is computed for both open loop and closed loop condition.The sensor-less current control method is implemented using the DsPIC30F2010 controller.The circuit performance is also verified from the simulation and hardware results.The proposed controller has inbuilt Analog-to-Digital Converter(ADC),Digital-to-Analog Converter(DAC),Pulse Width Modulation(PWM)generator,and provides fast responses.展开更多
This work presents a novel current-mode (CM) lossless integrator that uses one current differencing differential input transconductance amplifier (CDDITA) and one grounded capacitor. The configuration based on single ...This work presents a novel current-mode (CM) lossless integrator that uses one current differencing differential input transconductance amplifier (CDDITA) and one grounded capacitor. The configuration based on single active element has several advantages from the aspect of monolithic integration, few are: reduced power consumption, chip miniaturization. Employment of grounded capacitor is also beneficial for monolithic integration. Specifying some of the key features of integrator proposed are: 1) purely resistorless, 2) electronically tunable, 3) current output available at the port having high impedance, and 4) excellent performance under non-ideal conditions. So, a resister-less current mode lossy integrator with electronic control employing single CDDITA has been proposed in this paper. The verification of workability of the proposed current mode integrator is well explained by the help of SPICE simulations using TSMC CMOS 0.18 μm technology node.展开更多
This project proposes a novel dual-input matrix converter (DIMC) which is used to integrate the output of the wind energy to a power grid. The proposed matrix converter is developed based on the traditional indirect m...This project proposes a novel dual-input matrix converter (DIMC) which is used to integrate the output of the wind energy to a power grid. The proposed matrix converter is developed based on the traditional indirect matrix converter under reverse power flow operation mode, but with its six-switch voltage source converter replaced by a nine-switch configuration followed by the current source inverter (CSI). Matrix electric power conversion topologies and their switch functions are flexible and are used for specific applications. With the additional three switches, the proposed DIMC can provide six input terminals, which make it possible to integrate two independent AC sources from two independent wind turbines into a single grid tied power electronics interface. Commanded currents can be extracted from the two input sources to the grid. The proposed PI control and modulation schemes guaranteed sinusoidal input and output waveforms as well as reduced THD. The simulation results are provided to validate the effectiveness of the proposed control and modulation schemes for the proposed converter.展开更多
为使对换流阀工作状态的控制更加精确、抑制换相失败,提出了一种基于多分支多输入多输出(Multiple input multiple output,MIMO)深度学习的高压直流输电(Line commutated converter high voltage direct current,LCC-HVDC)换流器阀电流...为使对换流阀工作状态的控制更加精确、抑制换相失败,提出了一种基于多分支多输入多输出(Multiple input multiple output,MIMO)深度学习的高压直流输电(Line commutated converter high voltage direct current,LCC-HVDC)换流器阀电流波形反演方案。对现行实际工程中常用的基于差流换相失败的检测方案进行仿真分析,发现检测结果存在滞后性。阀电流波形的反演模型,其输入特征量为三相交流电流、输出量为6个阀电流,属于MIMO的场景。为提取更多特征信息,基于Inception-ResNet结构、采用多种不同尺寸的卷积,设计多分支MIMO深度学习的换流器阀电流反演模型,并以三相电流作为模型输入,6个阀电流作为输出量,对多分支MIMO模型进行训练。最后,对阀电流的波形进行预测反演。仿真结果表明,多分支MIMO模型对阀电流波形的反演具有较好的适用性,反演结果的相关系数在0.9836以上、平均绝对误差在0.1284以下、且均方误差在0.0286以内,误差变化程度较低。展开更多
文摘Based on the equivalent circuit model of a two-port optical receiver front-end,the relationship between the equivalent input noise current spectral density and the noise figure is analyzed. The derived relationship has universal validity for determining the equivalent input noise current spectral density for optical receiver designs, as verified by measuring a 155Mb/s high-impedance optical receiver front.end. Good agreement between calculated and simulated results has been achieved.
文摘The high corrosion resistance of duplex stainless steel （DSS） is due to elements such as Cr, Mo and N, hut also depends on the microstructure. The best general properties are obtained with approximately equal amounts of austenite and ferrite and the absence of third phases such as σ（sigma） and Cr2N. In the present work the effect of heat input variations on the microstructure and corrosion resistance of a DSS UNS S32760 in artificial sea water media were studied. The corrosion resistance in 3.5 % of NaCl solution was evaluated by potentiostatic polarization tests at room temperature. It is found that the presence of sigma phase and Cr2N decreases the corrosion potential. The specimen with heat input of approximately 0.95 kJ/mm have the best corrosion characteristics, which is the result for the lack of deleterious phases such as sigma and Cr2 N and balanced ferrite austenite proportion.
基金The National Natural Science Foundation of China under contract Nos 40930844 and 40976005
文摘Based on the data and method offered by Liu et al. （2009）, the direct wind and Stokes drift-induced energy inputs into the Ekman layer within the Antarctic Circumpolar Current （ACC） area are reestimated since the results of the former have been proved to be underestimated. And the result shows that the total rate of energy input into the Ekman-Stokes layer within the ACC area is 852.41 GW, including 649.75 GW of direct wind energy input （76%） and 202.66 GW of Stoke drift-induced energy input （24%）. Total increased energy input, due to wave-induced Coriolis-Stokes forcing added to the classical Ekman model, is 52.05 GW, accounting for 6.5% of the wind energy input into the classical Ekman layer. The long-term variability of direct wind and Stokes drift-induced energy inputs into the Ekman layer within the ACC is also investigated, and the result shows that the Stokes drift hinders the decadal increasing trend of direct wind energy input. Meanwhile, there is a period of 4-5 a in the energy spectrums, as same as the Antarctic circumpolar wave.
文摘In this paper, by change of integration path in complex spectrum domain and by defining input admittance as the ratio of complex radiated power to amplitude of square of voltage across the gap, new expressions of admittance (valid for all frequencies ) of infinitely long cylindrical antenna with and without conducting ground are obtained. Meanwhile corresponding formulas of current distribution are derived in detail. Some numerical computations are also given.
基金Supported by the National Natural Science Foundation of China(No.41176016)the National Basic Research Program of China(973 Program)(Nos.2012CB417402,2011CB403501)the Fund for Creative Research Groups by National Natural Science Foundation of China(No.41121064)
文摘The effects of different wind input and wave dissipation formulations on the steady Ekman current solution are described. Two formulations are considered: one from the wave modeling(WAM) program proposed by Hasselmann and Komen and the other provided by Tsagareli and Babanin. The solution adopted for our study was presented by Song for the wave-modifi ed Ekman current model that included the Stokes drift, wind input, and wave dissipation with eddy viscosity increasing linearly with depth. Using the Combi spectrum with tail effects, the solutions are calculated using two formulations for wind input and wave dissipation, and compared. Differences in the results are not negligible. Furthermore, the solution presented by Song and Xu for the eddy viscosity formulated using the K-Profi le Parameterization scheme under wind input and wave dissipation given by Tsagareli and Babanin is compared with that obtained for a depth-dependent eddy viscosity. The solutions are further compared with the available well-known observational data. The result indicates that the Tsagareli and Babanin scheme is more suitable for use in the model when capillary waves are included, and the solution calculated using the K-Profi le Parameterization scheme agrees best with observations.
基金supported by Libyan Cultural Affair/London,Libya under Grant No.13840.
文摘Single-phase,non-isolated microinverters used in photovoltaic(PV)systems commonly encounter two persistent challenges:High-frequency leakage current and fluctuating power delivery.This paper presents a novel single-phase,non-isolated,multi-input microinverter topology with a common-ground structure that effectively eliminates ground leakage current without requiring additional active components.The proposed microinverter architecture integrates a dual-boost configuration and uses only four active switches.This is especially advantageous in terms of the component count,which is beneficial to enhance reliability,reduce cost,and simplify the overall system design.With one,two,or four PV inputs,it can operate without interruption under unbalanced voltage or partial shading and even if some inputs drop to zero.A tailored modulation scheme minimizes conduction losses while maintaining a stable direct-current(DC)-link voltage,and a decoupling capacitor efficiently absorbs the single-phase pulsating power,thus overcoming one major limitation in existing microinverter designs.By validating with a 1-kW GaN-based prototype,both the simulated and experimental results demonstrate its high efficiency,robustness,and practical suitability for cost-effective PV applications,with a peak efficiency value of 94.8%.
文摘The concept of connecting two boost half bridge DC-DC converter modules in input-paral- lel output-parallel configuration is presented. The input-parallel-output-parallel （IPOP） converter consists of multiple boost half bridge （BHB） DC-DC converter modules which are connected in par- allel at the input and output side. This kind of converter is an attractive solution for high power ap- plications. The correlation between input current sharing （ICS） and output current sharing （OCS） of the IPOP converter basic modules is described. Two loop control strategies, consisting of input cur- rent loop and output voltage loop, have been developed to achieve equal ICS and OCS in this present work. The control strategy for the IPOP configuration of boost haft bridge DC-DC converter has been verified for different load conditions （half load and full load）, The IPOP system proposed here is comprising of two modules but it can be extended to three or more. The performance of the pro- posed system along with the control strategy is verified by simulation in MATLAB using Simpower tool. Finally the satisfactory simulation results are obtained.
文摘Multi-modular system plays an important role in power system architecture because low voltage and low power converters can be connected in any combination parallel or series at input/ output side in order to obtained any given power system specifications. Multi-modular boost haft bridge DC-DC converter in the configuration of input series output parallel has been investigated in this paper. The boost half bridge DC-DC converters are connected in input series output parallel con- figuration in order to achieve equal input voltage sharing and output current sharing between the con- verters. This can be achieved with the help of dynamic control scheme which consists of two loops, a voltage loop and a current loop, for each module. Dynamic behavior of multi-modular converter configuration has been observe by varying the load condition. Moreover, the results obtained through multi-modular converter describe that the system has good dynamic and steady state response. Al- though two converter modules are focused in this paper but it can be modified to any number of modules.
文摘This paper presents an efficient supply current wave shaping technique for bridgeless interleaved Single Ended Primary Inductor Converter(SEPIC).The SEPIC converter converts an Alternating Current(AC)to Direct Current(DC)with the boost converter.Power Factor Correction(PFC)is progressively significant to achieve high energy efficiency.The overall system efficiency can be increased as the bridgeless topology has less conduction losses from rectifying bridges.Also,the bridgeless and interleaved techniques are incorporated in this study to achieve better performance.The performance of the system is analyzed on both current control and sensor-less techniques.Different controllers such as Proportional Integral(PI)control,peak current control,Non-Linear Carrier(NLC)control,and sensor-less current control are integrated.All the above controllers are implemented using MATrix LABoratory(MATLAB)/SIMULINK.The performance parameter,namely Power Factor(PF),Total Harmonic Distortion(THD),is computed for both open loop and closed loop condition.The sensor-less current control method is implemented using the DsPIC30F2010 controller.The circuit performance is also verified from the simulation and hardware results.The proposed controller has inbuilt Analog-to-Digital Converter(ADC),Digital-to-Analog Converter(DAC),Pulse Width Modulation(PWM)generator,and provides fast responses.
文摘This work presents a novel current-mode (CM) lossless integrator that uses one current differencing differential input transconductance amplifier (CDDITA) and one grounded capacitor. The configuration based on single active element has several advantages from the aspect of monolithic integration, few are: reduced power consumption, chip miniaturization. Employment of grounded capacitor is also beneficial for monolithic integration. Specifying some of the key features of integrator proposed are: 1) purely resistorless, 2) electronically tunable, 3) current output available at the port having high impedance, and 4) excellent performance under non-ideal conditions. So, a resister-less current mode lossy integrator with electronic control employing single CDDITA has been proposed in this paper. The verification of workability of the proposed current mode integrator is well explained by the help of SPICE simulations using TSMC CMOS 0.18 μm technology node.
文摘This project proposes a novel dual-input matrix converter (DIMC) which is used to integrate the output of the wind energy to a power grid. The proposed matrix converter is developed based on the traditional indirect matrix converter under reverse power flow operation mode, but with its six-switch voltage source converter replaced by a nine-switch configuration followed by the current source inverter (CSI). Matrix electric power conversion topologies and their switch functions are flexible and are used for specific applications. With the additional three switches, the proposed DIMC can provide six input terminals, which make it possible to integrate two independent AC sources from two independent wind turbines into a single grid tied power electronics interface. Commanded currents can be extracted from the two input sources to the grid. The proposed PI control and modulation schemes guaranteed sinusoidal input and output waveforms as well as reduced THD. The simulation results are provided to validate the effectiveness of the proposed control and modulation schemes for the proposed converter.
文摘为使对换流阀工作状态的控制更加精确、抑制换相失败,提出了一种基于多分支多输入多输出(Multiple input multiple output,MIMO)深度学习的高压直流输电(Line commutated converter high voltage direct current,LCC-HVDC)换流器阀电流波形反演方案。对现行实际工程中常用的基于差流换相失败的检测方案进行仿真分析,发现检测结果存在滞后性。阀电流波形的反演模型,其输入特征量为三相交流电流、输出量为6个阀电流,属于MIMO的场景。为提取更多特征信息,基于Inception-ResNet结构、采用多种不同尺寸的卷积,设计多分支MIMO深度学习的换流器阀电流反演模型,并以三相电流作为模型输入,6个阀电流作为输出量,对多分支MIMO模型进行训练。最后,对阀电流的波形进行预测反演。仿真结果表明,多分支MIMO模型对阀电流波形的反演具有较好的适用性,反演结果的相关系数在0.9836以上、平均绝对误差在0.1284以下、且均方误差在0.0286以内,误差变化程度较低。
