The influence of geometric configuration on the friction characteristics during incremental sheet forming of AA5052 was analyzed by integrating surface morphology and its characteristic parameters,along with plastic s...The influence of geometric configuration on the friction characteristics during incremental sheet forming of AA5052 was analyzed by integrating surface morphology and its characteristic parameters,along with plastic strain,contact pressure,and area.The interface promotes lubrication and support when wall angles were≤40°,a 0.5 mm-thin sheet was used,and a 10 mm-large tool radius was employed.This mainly results in micro-plowing and plastic extrusion flow,leading to lower friction coefficient.However,when wall angles exceed 40°,significant plastic strain roughening occurs,leading to inadequate lubrication on the newly formed surface.Increased sheet thickness and decreased tool radius elevate contact pressure.These actions trigger micro-cutting and adhesion,potentially leading to localized scuffing and dimple tears,and higher friction coefficient.The friction mechanisms remain unaffected by the part’s plane curve features.As the forming process progresses,abrasive wear intensifies,and surface morphology evolves unfavorably for lubrication and friction reduction.展开更多
The radar radiation source signals hold extremely high reconnaissance value.Accurately positioning these signals constitutes one of the key technologies in safeguarding the security of the electromagnetic space.The po...The radar radiation source signals hold extremely high reconnaissance value.Accurately positioning these signals constitutes one of the key technologies in safeguarding the security of the electromagnetic space.The positioning error in multi-station scenarios is influenced not only by the accuracy of positioning parameter estimation but also by the geometric configuration of the positioning platform.This paper focuses on the direction of arrival(DOA),frequency difference of arrival(FDOA),and time difference of arrival(TDOA)methods,analyzing the optimal configuration,optimal detection area,and optimal position dilution of precision in both elevation-known and elevation-unknown scenarios.Specifically,the paper constructs a signal receiving model,establishes the corresponding positioning equations,and performs dimensional normalization on these equations to derive measurement values in meters.Through differential processing,the position dilution of precision is obtained,which is then used as the optimization function to determine the optimal configuration,optimal detection area,and optimal position dilution of precision.Simulation results validate the accuracy of the proposed formulas.展开更多
The Wilczek–Zee connection(WZC)is a key concept in the study of topology of quantum systems.Here,we introduce the double Wilczek–Zee connection(DWZC)which naturally appears in the pure-state quantum geometric tensor...The Wilczek–Zee connection(WZC)is a key concept in the study of topology of quantum systems.Here,we introduce the double Wilczek–Zee connection(DWZC)which naturally appears in the pure-state quantum geometric tensor(QGT),another important concept in the field of quantum geometry.The DWZC is Hermitian with respect to the two integer indices,just like the original Hermitian WZC.Based on the symmetric logarithmic derivative operator,we propose a mixed-state quantum geometric tensor.Using the symmetric properties of the DWZC,we find that the real part of the QGT is connected to the real part of the DWZC and the square of eigenvalue differences of the density matrix,whereas the imaginary part can be given in terms of the imaginary part of the DWZC and the cube of the eigenvalue differences.For density matrices with full rank or no full rank,the QGT can be given in terms of real and imaginary parts of the DWZC.展开更多
Granular debris plays a significant role in determining damming deposit characteristics. An indepth understanding of how variations in grain size distribution(GSD) and geometric configurations impact the behavior of g...Granular debris plays a significant role in determining damming deposit characteristics. An indepth understanding of how variations in grain size distribution(GSD) and geometric configurations impact the behavior of granular debris during the occurrence of granular debris is essential for precise assessment and effective mitigation of landslide hazards in mountainous terrains. This research aims to investigate the impact of GSD and geometric configurations on sliding and damming properties through laboratory experiments. The geometric configurations were categorized into three categories based on the spatial distribution of maximum volume: located at the front(Type Ⅰ), middle(Type Ⅱ), and rear(Type Ⅲ) of the granular debris. Our experimental findings highlight that the sliding and damming processes primarily depend on the interaction among the geometric configuration, grain size, and GSD in granular debris. Different sliding and damming mechanisms across various geometric configurations induce variability in motion parameters and deposition patterns. For Type Ⅰ configurations, the front debris functions as the critical and primary driving component, with energy dissipation primarily occurring through inter-grain interactions. In contrast, Type Ⅱ configurations feature the middle debris as the dominant driving component, experiencing hindrance from the front debris and propulsion from the rear, leading to complex alterations in sliding motion. Here, energy dissipation arises from a combination of inter-grain and grain-substrate interactions. Lastly, in Type Ⅲ configurations, both the middle and rear debris serve as the main driving components, with the rear sliding debris impeded by the front. In this case, energy dissipation predominantly results from grainsubstrate interaction. Moreover, we have quantitatively demonstrated that the inverse grading in damming deposits, where coarse grain moves upward and fine grain moves downward, is primarily caused by grain sorting due to collisions among the grains and between the grain and the base. The impact of grain on the horizontal channel further aids grain sorting and contributes to inverse grading. The proposed classification of three geometric configurations in our study enhances the understanding of damming properties from the view of mechanism, which provides valuable insights for related study about damming granular debris.展开更多
The neuron growth will bring series variation to the neuron characteristics of geometric configuration. Especially the growth of dendrite and axon can obviously change the space characteristic and geometric characteri...The neuron growth will bring series variation to the neuron characteristics of geometric configuration. Especially the growth of dendrite and axon can obviously change the space characteristic and geometric characteristic of neuron. This article is to build the prediction model of neuron growth through knowing the statistics rules of neuron geometric characteristics, better imitate the neuron growth, and clearly analyze the growth influence of geometric configuration.展开更多
Boundary conditions constructed by two typical geometrical configurations related to the manufacturing methods of bronze process and tin-rich Nb tube method have been considered in a diffusion model in which the diffu...Boundary conditions constructed by two typical geometrical configurations related to the manufacturing methods of bronze process and tin-rich Nb tube method have been considered in a diffusion model in which the diffusion of Sn in CuSn matrix plays a major role is as- sumed.The dependence of thickness of Nb_3Sn layer on reaction time has been derived.It is shown that the growth rate of Nb_3Sn relates to the configuration of the superconductor,the geometrical parameters of Nb filaments and CuSn matrix.The theory is qualitatively con- sistent with the experimental results.展开更多
Geometrical configurations play a crucial role in dual-atom catalysts(DACs)for electrocatalytic applications.Significant progress has been made to design DACs electrocatalysts with various geometri-cal configurations,...Geometrical configurations play a crucial role in dual-atom catalysts(DACs)for electrocatalytic applications.Significant progress has been made to design DACs electrocatalysts with various geometri-cal configurations,but in-depth understanding the relationship between geometrical configurations and metal-metal interaction mechanisms for designing targeted DACs is still required.In this review,the recent progress in engineering of geometrical configurations of DACs is systematically summarized.Based on the polarity of geometrical configuration,DACs can be classified into two different types that are homonuclear and heteronuclear DACs.Furthermore,with regard to the geometrical configurations of the active sites,homonuclear DACs are identified into adjacent and bridged configurations,and heteronuclear DACs can be classified into adjacent,bridged,and separated configurations.Subsequently,metal-metal interactions in DACs with different geometrical configurations are introduced.Additionally,the applications of DACs in different electrocatalytic reactions are discussed,including the oxygen reduction reaction(ORR),oxygen evolution reaction(OER),hydrogen evolution reaction(HER),and other catalysis.Finally,the future challenges and perspectives for advancements in DACs are high-lighted.This review aims to provide inspiration for the design of highly effcient DACs towards energy relatedapplications.展开更多
The CNC machine tool is the fundamental equipment of the manufacturing industry,particularly in sectors where achieving high levels of accuracy is crucial.Geometric accuracy design is an important step in machine tool...The CNC machine tool is the fundamental equipment of the manufacturing industry,particularly in sectors where achieving high levels of accuracy is crucial.Geometric accuracy design is an important step in machine tool design and plays an essential role in determining the machining accuracy of the workpiece.Researchers have extensively studied methods to model,extract,optimize,and measure the geometric errors that affect the geometric accuracy of machine tools.This paper provides a comprehensive review of the state-of-the-art approaches and an overview of the latest research progress associated with geometric accuracy design in CNC machine tools.This paper explores the interrelated aspects of CNC machine tool accuracy design:modeling,analysis and optimization.Accuracy analysis,which includes geometric error modeling and sensitivity analysis,determines a machine tool’s output accuracy through its volumetric error model,given the known accuracy of its individual components.Conversely,accuracy allocation designs the accuracy of the machine tool components according to given output accuracy requirements to achieve optimization between the objectives of manufacturing cost,quality,reliability,and environmental impact.In addition to discussing design factors and evaluation methods,this paper outlines methods for verifying the accuracy of design results,aiming to provide a practical basis for ensuring that the designed accuracy is achieved.Finally,the challenges and future research directions in geometric accuracy design are highlighted.展开更多
Owing to the outstanding optoelectronic properties of perovskite materials,perovskite solar cells(PSCs)have been widely studied by academic organizations and industry corporations,with great potential to become the ne...Owing to the outstanding optoelectronic properties of perovskite materials,perovskite solar cells(PSCs)have been widely studied by academic organizations and industry corporations,with great potential to become the next-generation commercial solar cells.However,critical challenges remain in preserving high efficiency practical large-scale commercialized PSCs:a)the long-term stability of the cell materials and devices,b)lead leakage,and c)methods to scale the cells for larger area applications.This paper summarizes the prior-art strategies to address the above challenges,including the latest studies on the traditional glass-glass and thin-film encapsulation methods to better improve the reliability of PSCs,new technologies for preventing lead leakage,and geometric improvement strategies to enhance the reliability,efficiency,and performance of perovskite solar modules(PSMs).Through these strategies,the device achieved enhanced performance in long-term stability tests.The encapsulation resulted in a high lead leakage inhibition rate of up to 99%,and the PSMs possessed a geometric fill factor of 99.6%and a power conversion efficiency(PCE)of 20.7%.The dramatic improvement of efficiency and reliability of perovskite solar cells and modules indicate the great potential for mass production and commer-cialization of perovskite solar applications in the near future.展开更多
The proposed hybrid optimization algorithm integrates particle swarm optimizatio(PSO)with Ant Colony Optimization(ACO)to improve a number of pitfalls within PSO methods traditionally considered and/or applied to indus...The proposed hybrid optimization algorithm integrates particle swarm optimizatio(PSO)with Ant Colony Optimization(ACO)to improve a number of pitfalls within PSO methods traditionally considered and/or applied to industrial robots.Particle Swarm Optimization may frequently suffer from local optima and inaccuracies in identifying the geometric parameters,which are necessary for applications requiring high-accuracy performances.The proposed approach integrates pheromone-based learning of ACO with the D-H method of developing an error model;hence,the global search effectiveness together with the convergence accuracy is further improved.Comparison studies of the hybrid PSO-ACO algorithm show higher precision and effectiveness in the optimization of geometric error parameters compared to the traditional methods.This is a remarkable reduction of localization errors,thus yielding accuracy and reliability in industrial robotic systems,as the results show.This approach improves performance in those applications that demand high geometric calibration by reducing the geometric error.The paper provides an overview of input for developing robotics and automation,giving importance to precision in industrial engineering.The proposed hybrid methodology is a good way to enhance the working accuracy and effectiveness of industrial robots and shall enable their wide application to complex tasks that require a high degree of accuracy.展开更多
In machine vision,elliptical targets frequently appear within the camera's region of interest(ROI).Ellipse detection is essential for shape detection and geometric measurements in machine vision.However,existing e...In machine vision,elliptical targets frequently appear within the camera's region of interest(ROI).Ellipse detection is essential for shape detection and geometric measurements in machine vision.However,existing ellipse detection algorithms often face issues such as high computational complexity,strong dependence on initial conditions,sensitivity to noise,and lack of robustness to occlusions.In this paper,we propose a fast and robust ellipse detection method to address these challenges.This method first utilizes edge gradient and curvature information to segment the curve into circular arcs.Next,based on the convexity of the arcs,it divides them into different quadrants of the ellipse,groups and fits the arcs according to multiple geometric constraints at a low computational cost.Finally,it reduces the parameter space for hierarchical clustering and then segments the complete ellipse into several sectors for verification.We compare our method across seven datasets,including five public image datasets and two from industrial camera scenes.Experimental results show that our method achieves a precision ranging from 67.1%to 98.9%,a recall ranging from 48.1%to 92.9%,and an F-measure ranging from 58.0%to 95.8%.The average execution time per image ranges from 25 ms to 192 ms,demonstrating both high accuracy and efficiency.展开更多
A new analytical model for geometric size and forming force prediction in incremental flanging(IF)is presented in this work.The complex deformation characteristics of IF are considered in the modeling process,which ca...A new analytical model for geometric size and forming force prediction in incremental flanging(IF)is presented in this work.The complex deformation characteristics of IF are considered in the modeling process,which can accurately describe the strain and stress states in IF.Based on strain analysis,the model can predict the material thickness distribution and neck height after IF.By considering contact area,strain characteristics,material thickness changes,and friction,the model can predict specific moments and corresponding values of maximum axial forming force and maximum horizontal forming force during IF.In addition,an IF experiment involving different tool diameters,flanging diameters,and opening hole diameters is conducted.On the basis of the experimental strain paths,the strain characteristics of different deformation zones are studied,and the stable strain ratio is quantitatively described through two dimensionless parameters:relative tool diameter and relative hole diameter.Then,the changing of material thickness and forming force in IF,and the variation of minimum material thickness,neck height,maximum axial forming force,and maximum horizontal forming force with flanging parameters are studied,and the reliability of the analytical model is verified in this process.Finally,the influence of the horizontal forming force on the tool design and the fluctuation of the forming force are explained.展开更多
Accuracy allocation is crucial in the accuracy design of machining tools.Current accuracy allocation methods primarily focus on positional deviation,with little consideration for tool direction deviation.To address th...Accuracy allocation is crucial in the accuracy design of machining tools.Current accuracy allocation methods primarily focus on positional deviation,with little consideration for tool direction deviation.To address this issue,we propose a geometric error cost sensitivity-based accuracy allocation method for five-axis machine tools.A geometric error model consisting of 4l error components is constructed based on homogeneous transformation matrices.Volumetric points with positional and tool direction deviations are randomly sampled to evaluate the accuracy of the machine tool.The sensitivity of each error component at these sampling points is analyzed using the Sobol method.To balance the needs of geometric precision and manufacturing cost,a geometric error cost sensitivity function is developed to estimate the required cost.By allocating error components affecting tool direction deviation first and the remaining components second,this allocation scheme ensures that both deviations meet the requirements.We also perform numerical simulation of a BC-type(B-axis and C-axis type)five-axis machine tool to validate the method.The results show that the new allocation scheme reduces the total geometric error cost by 27.8%compared to a uniform allocation scheme,and yields the same positional and tool direction machining accuracies.展开更多
The quantum geometric tensor(QGT)is a fundamental quantity for characterizing the geometric properties of quantum states and plays an essential role in elucidating various physical phenomena.The traditional QGT,defned...The quantum geometric tensor(QGT)is a fundamental quantity for characterizing the geometric properties of quantum states and plays an essential role in elucidating various physical phenomena.The traditional QGT,defned only for pure states,has limited applicability in realistic scenarios where mixed states are common.To address this limitation,we generalize the defnition of the QGT to mixed states using the purifcation bundle and the covariant derivative.Notably,our proposed defnition reduces to the traditional QGT when mixed states approach pure states.In our framework,the real and imaginary parts of this generalized QGT correspond to the Bures metric and the mean gauge curvature,respectively,endowing it with a broad range of potential applications.Additionally,using our proposed mixed-state QGT,we derive the geodesic equation applicable to mixed states.This work establishes a unifed framework for the geometric analysis of both pure and mixed states,thereby deepening our understanding of the geometric properties of quantum states.展开更多
In this paper,we study the geometric ergodicity of continuous time Markov pro-cesses in general state space.For the geometric ergodic continuous time Markov processes,the condition π(f^(p))<∞,p>1 is added.Usin...In this paper,we study the geometric ergodicity of continuous time Markov pro-cesses in general state space.For the geometric ergodic continuous time Markov processes,the condition π(f^(p))<∞,p>1 is added.Using the coupling method,we obtain the existence of a full absorbing set on which continuous time Markov processes are f-geometric ergodic.展开更多
Background As visual simultaneous localization and mapping(SLAM)is primarily based on the assumption of a static scene,the presence of dynamic objects in the frame causes problems such as a deterioration of system rob...Background As visual simultaneous localization and mapping(SLAM)is primarily based on the assumption of a static scene,the presence of dynamic objects in the frame causes problems such as a deterioration of system robustness and inaccurate position estimation.In this study,we propose a YGC-SLAM for indoor dynamic environments based on the ORB-SLAM2 framework combined with semantic and geometric constraints to improve the positioning accuracy and robustness of the system.Methods First,the recognition accuracy of YOLOv5 was improved by introducing the convolution block attention model and the improved EIOU loss function,whereby the prediction frame converges quickly for better detection.The improved YOLOv5 was then added to the tracking thread for dynamic target detection to eliminate dynamic points.Subsequently,multi-view geometric constraints were used for re-judging to further eliminate dynamic points while enabling more useful feature points to be retained and preventing the semantic approach from over-eliminating feature points,causing a failure of map building.The K-means clustering algorithm was used to accelerate this process and quickly calculate and determine the motion state of each cluster of pixel points.Finally,a strategy for drawing keyframes with de-redundancy was implemented to construct a clear 3D dense static point-cloud map.Results Through testing on TUM dataset and a real environment,the experimental results show that our algorithm reduces the absolute trajectory error by 98.22%and the relative trajectory error by 97.98%compared with the original ORBSLAM2,which is more accurate and has better real-time performance than similar algorithms,such as DynaSLAM and DS-SLAM.Conclusions The YGC-SLAM proposed in this study can effectively eliminate the adverse effects of dynamic objects,and the system can better complete positioning and map building tasks in complex environments.展开更多
The structure and electronic properties of Co_(2)Ge_(10)^(-)anion and its neutral counterpart were investigated by anion photoelectron spectroscopy and theoretical calculations.The experimental vertical detachment ene...The structure and electronic properties of Co_(2)Ge_(10)^(-)anion and its neutral counterpart were investigated by anion photoelectron spectroscopy and theoretical calculations.The experimental vertical detachment energy of Co_(2)Ge_(10)^(-)was measured to be 2.86±0.08 eV.The lowest-energy isomer of Co_(2)Ge_(10)^(-)is in a doublet state and has a cage-like structure with Cs symmetry,which can be constructed by a tetragonal bipyramid on top of a pentagonal bipyramid and these two bipyramid structures share a common Co atom.The most stable structure of neutral Co_(2)Ge_(10)resembles its anionic counterpart and it is in a triplet state.The natural population analysis showed that the inner Co atom of both the anionic and neutral Co_(2)Ge_(10)acquires negative charge from the neighboring Ge atoms.The outer Co atom has a larger spin moment than the inner Co atom,indicating that the magnetic moments of Co_(2)Ge_(10)^(-/0)are mainly contributed by the outer Co atom.Analyses of the density of states and molecular orbitals indicated that there are a few highly delocalized molecular orbitals in Co_(2)Ge_(10)^(-),which are mainly contributed by Ge 4s atomic orbitals.展开更多
In this paper,we introduce a new geometric constant R_(X)(κ)based on isosceles orthogonality.First,we explore some basic properties of this new constant and then provide several examples to estimate its exact values ...In this paper,we introduce a new geometric constant R_(X)(κ)based on isosceles orthogonality.First,we explore some basic properties of this new constant and then provide several examples to estimate its exact values in certain specific Banach spaces.Next,we investigate the relationships between this new constant and other classical constants.Specifically,we establish an inequality relationship between it and the J(X)constant,as well as an identity relationship between it and theρX(t)constant.Furthermore,we characterize some geometric properties of Banach spaces by means of this new constant.Finally,by restricting the above-mentioned constant to the unit sphere,we introduce another new constant,calculate its upper and lower bounds,and present a relevant example.展开更多
This paper investigates the development and performance of a new higher-order geometric stiffness matrix that more closely approximates the theoretically derived stiffness coefficients.Factors that influence the accur...This paper investigates the development and performance of a new higher-order geometric stiffness matrix that more closely approximates the theoretically derived stiffness coefficients.Factors that influence the accuracy of the solution are studied using two columns,two braced frames,and one unbraced frame.Discussion is provided when the new geometric stiffness matrix can be used to improve the buckling load analysis results and when it may provide only nominal additional benefit.展开更多
基金the support of the Key Research and Development Program of Shaanxi Province,China(No.2021GXLH-Z-049)。
文摘The influence of geometric configuration on the friction characteristics during incremental sheet forming of AA5052 was analyzed by integrating surface morphology and its characteristic parameters,along with plastic strain,contact pressure,and area.The interface promotes lubrication and support when wall angles were≤40°,a 0.5 mm-thin sheet was used,and a 10 mm-large tool radius was employed.This mainly results in micro-plowing and plastic extrusion flow,leading to lower friction coefficient.However,when wall angles exceed 40°,significant plastic strain roughening occurs,leading to inadequate lubrication on the newly formed surface.Increased sheet thickness and decreased tool radius elevate contact pressure.These actions trigger micro-cutting and adhesion,potentially leading to localized scuffing and dimple tears,and higher friction coefficient.The friction mechanisms remain unaffected by the part’s plane curve features.As the forming process progresses,abrasive wear intensifies,and surface morphology evolves unfavorably for lubrication and friction reduction.
基金supported by the National Natural Science Foundation of China(Nos.62027801,62301035).
文摘The radar radiation source signals hold extremely high reconnaissance value.Accurately positioning these signals constitutes one of the key technologies in safeguarding the security of the electromagnetic space.The positioning error in multi-station scenarios is influenced not only by the accuracy of positioning parameter estimation but also by the geometric configuration of the positioning platform.This paper focuses on the direction of arrival(DOA),frequency difference of arrival(FDOA),and time difference of arrival(TDOA)methods,analyzing the optimal configuration,optimal detection area,and optimal position dilution of precision in both elevation-known and elevation-unknown scenarios.Specifically,the paper constructs a signal receiving model,establishes the corresponding positioning equations,and performs dimensional normalization on these equations to derive measurement values in meters.Through differential processing,the position dilution of precision is obtained,which is then used as the optimization function to determine the optimal configuration,optimal detection area,and optimal position dilution of precision.Simulation results validate the accuracy of the proposed formulas.
基金Project supported by Quantum Science and Technology–National Science and Technology Major Project(Grant No.2024ZD0301000)the National Natural Science Foundation of China(Grant No.12305031)+1 种基金the Hangzhou Joint Fund of the Natural Science Foundation of Zhejiang Province,China(Grant No.LHZSD24A050001)the Science Foundation of Zhejiang Sci-Tech University(Grant Nos.23062088Y and 23062153-Y)。
文摘The Wilczek–Zee connection(WZC)is a key concept in the study of topology of quantum systems.Here,we introduce the double Wilczek–Zee connection(DWZC)which naturally appears in the pure-state quantum geometric tensor(QGT),another important concept in the field of quantum geometry.The DWZC is Hermitian with respect to the two integer indices,just like the original Hermitian WZC.Based on the symmetric logarithmic derivative operator,we propose a mixed-state quantum geometric tensor.Using the symmetric properties of the DWZC,we find that the real part of the QGT is connected to the real part of the DWZC and the square of eigenvalue differences of the density matrix,whereas the imaginary part can be given in terms of the imaginary part of the DWZC and the cube of the eigenvalue differences.For density matrices with full rank or no full rank,the QGT can be given in terms of real and imaginary parts of the DWZC.
基金support of the National Natural Science Foundation of China(U20A20111,42107189).
文摘Granular debris plays a significant role in determining damming deposit characteristics. An indepth understanding of how variations in grain size distribution(GSD) and geometric configurations impact the behavior of granular debris during the occurrence of granular debris is essential for precise assessment and effective mitigation of landslide hazards in mountainous terrains. This research aims to investigate the impact of GSD and geometric configurations on sliding and damming properties through laboratory experiments. The geometric configurations were categorized into three categories based on the spatial distribution of maximum volume: located at the front(Type Ⅰ), middle(Type Ⅱ), and rear(Type Ⅲ) of the granular debris. Our experimental findings highlight that the sliding and damming processes primarily depend on the interaction among the geometric configuration, grain size, and GSD in granular debris. Different sliding and damming mechanisms across various geometric configurations induce variability in motion parameters and deposition patterns. For Type Ⅰ configurations, the front debris functions as the critical and primary driving component, with energy dissipation primarily occurring through inter-grain interactions. In contrast, Type Ⅱ configurations feature the middle debris as the dominant driving component, experiencing hindrance from the front debris and propulsion from the rear, leading to complex alterations in sliding motion. Here, energy dissipation arises from a combination of inter-grain and grain-substrate interactions. Lastly, in Type Ⅲ configurations, both the middle and rear debris serve as the main driving components, with the rear sliding debris impeded by the front. In this case, energy dissipation predominantly results from grainsubstrate interaction. Moreover, we have quantitatively demonstrated that the inverse grading in damming deposits, where coarse grain moves upward and fine grain moves downward, is primarily caused by grain sorting due to collisions among the grains and between the grain and the base. The impact of grain on the horizontal channel further aids grain sorting and contributes to inverse grading. The proposed classification of three geometric configurations in our study enhances the understanding of damming properties from the view of mechanism, which provides valuable insights for related study about damming granular debris.
文摘The neuron growth will bring series variation to the neuron characteristics of geometric configuration. Especially the growth of dendrite and axon can obviously change the space characteristic and geometric characteristic of neuron. This article is to build the prediction model of neuron growth through knowing the statistics rules of neuron geometric characteristics, better imitate the neuron growth, and clearly analyze the growth influence of geometric configuration.
文摘Boundary conditions constructed by two typical geometrical configurations related to the manufacturing methods of bronze process and tin-rich Nb tube method have been considered in a diffusion model in which the diffusion of Sn in CuSn matrix plays a major role is as- sumed.The dependence of thickness of Nb_3Sn layer on reaction time has been derived.It is shown that the growth rate of Nb_3Sn relates to the configuration of the superconductor,the geometrical parameters of Nb filaments and CuSn matrix.The theory is qualitatively con- sistent with the experimental results.
基金supported by the Natural Science Foundation of China (22179062,52125202,and U2004209)the Natural Science Foundation of Jiangsu Province (BK20230035)+1 种基金the Fundamental Research Funds for the Central Universities (30922010303)the Intergovernmental Cooperation Projects in the National Key Research and Development Plan of the Ministry of Science and Technology of PRC (2022YFE0196800)
文摘Geometrical configurations play a crucial role in dual-atom catalysts(DACs)for electrocatalytic applications.Significant progress has been made to design DACs electrocatalysts with various geometri-cal configurations,but in-depth understanding the relationship between geometrical configurations and metal-metal interaction mechanisms for designing targeted DACs is still required.In this review,the recent progress in engineering of geometrical configurations of DACs is systematically summarized.Based on the polarity of geometrical configuration,DACs can be classified into two different types that are homonuclear and heteronuclear DACs.Furthermore,with regard to the geometrical configurations of the active sites,homonuclear DACs are identified into adjacent and bridged configurations,and heteronuclear DACs can be classified into adjacent,bridged,and separated configurations.Subsequently,metal-metal interactions in DACs with different geometrical configurations are introduced.Additionally,the applications of DACs in different electrocatalytic reactions are discussed,including the oxygen reduction reaction(ORR),oxygen evolution reaction(OER),hydrogen evolution reaction(HER),and other catalysis.Finally,the future challenges and perspectives for advancements in DACs are high-lighted.This review aims to provide inspiration for the design of highly effcient DACs towards energy relatedapplications.
基金Supported by the National Natural Science Foundation of China(Grant Nos.52375448,52275440).
文摘The CNC machine tool is the fundamental equipment of the manufacturing industry,particularly in sectors where achieving high levels of accuracy is crucial.Geometric accuracy design is an important step in machine tool design and plays an essential role in determining the machining accuracy of the workpiece.Researchers have extensively studied methods to model,extract,optimize,and measure the geometric errors that affect the geometric accuracy of machine tools.This paper provides a comprehensive review of the state-of-the-art approaches and an overview of the latest research progress associated with geometric accuracy design in CNC machine tools.This paper explores the interrelated aspects of CNC machine tool accuracy design:modeling,analysis and optimization.Accuracy analysis,which includes geometric error modeling and sensitivity analysis,determines a machine tool’s output accuracy through its volumetric error model,given the known accuracy of its individual components.Conversely,accuracy allocation designs the accuracy of the machine tool components according to given output accuracy requirements to achieve optimization between the objectives of manufacturing cost,quality,reliability,and environmental impact.In addition to discussing design factors and evaluation methods,this paper outlines methods for verifying the accuracy of design results,aiming to provide a practical basis for ensuring that the designed accuracy is achieved.Finally,the challenges and future research directions in geometric accuracy design are highlighted.
基金supported by the National Natural Science Foundation of China(No.62404041)the Natural Science Foundation of Jiangsu Province of China(No.BK20230830).
文摘Owing to the outstanding optoelectronic properties of perovskite materials,perovskite solar cells(PSCs)have been widely studied by academic organizations and industry corporations,with great potential to become the next-generation commercial solar cells.However,critical challenges remain in preserving high efficiency practical large-scale commercialized PSCs:a)the long-term stability of the cell materials and devices,b)lead leakage,and c)methods to scale the cells for larger area applications.This paper summarizes the prior-art strategies to address the above challenges,including the latest studies on the traditional glass-glass and thin-film encapsulation methods to better improve the reliability of PSCs,new technologies for preventing lead leakage,and geometric improvement strategies to enhance the reliability,efficiency,and performance of perovskite solar modules(PSMs).Through these strategies,the device achieved enhanced performance in long-term stability tests.The encapsulation resulted in a high lead leakage inhibition rate of up to 99%,and the PSMs possessed a geometric fill factor of 99.6%and a power conversion efficiency(PCE)of 20.7%.The dramatic improvement of efficiency and reliability of perovskite solar cells and modules indicate the great potential for mass production and commer-cialization of perovskite solar applications in the near future.
文摘The proposed hybrid optimization algorithm integrates particle swarm optimizatio(PSO)with Ant Colony Optimization(ACO)to improve a number of pitfalls within PSO methods traditionally considered and/or applied to industrial robots.Particle Swarm Optimization may frequently suffer from local optima and inaccuracies in identifying the geometric parameters,which are necessary for applications requiring high-accuracy performances.The proposed approach integrates pheromone-based learning of ACO with the D-H method of developing an error model;hence,the global search effectiveness together with the convergence accuracy is further improved.Comparison studies of the hybrid PSO-ACO algorithm show higher precision and effectiveness in the optimization of geometric error parameters compared to the traditional methods.This is a remarkable reduction of localization errors,thus yielding accuracy and reliability in industrial robotic systems,as the results show.This approach improves performance in those applications that demand high geometric calibration by reducing the geometric error.The paper provides an overview of input for developing robotics and automation,giving importance to precision in industrial engineering.The proposed hybrid methodology is a good way to enhance the working accuracy and effectiveness of industrial robots and shall enable their wide application to complex tasks that require a high degree of accuracy.
基金supported by National Major Scientific Research Instrument Development Project of China(No.51927804)Science Fund for Shaanxi Provincial Department of Education's Youth Innovation Team Research Plan under Grant(No.23JP169).
文摘In machine vision,elliptical targets frequently appear within the camera's region of interest(ROI).Ellipse detection is essential for shape detection and geometric measurements in machine vision.However,existing ellipse detection algorithms often face issues such as high computational complexity,strong dependence on initial conditions,sensitivity to noise,and lack of robustness to occlusions.In this paper,we propose a fast and robust ellipse detection method to address these challenges.This method first utilizes edge gradient and curvature information to segment the curve into circular arcs.Next,based on the convexity of the arcs,it divides them into different quadrants of the ellipse,groups and fits the arcs according to multiple geometric constraints at a low computational cost.Finally,it reduces the parameter space for hierarchical clustering and then segments the complete ellipse into several sectors for verification.We compare our method across seven datasets,including five public image datasets and two from industrial camera scenes.Experimental results show that our method achieves a precision ranging from 67.1%to 98.9%,a recall ranging from 48.1%to 92.9%,and an F-measure ranging from 58.0%to 95.8%.The average execution time per image ranges from 25 ms to 192 ms,demonstrating both high accuracy and efficiency.
基金supported in part by financial support from the National Key R&D Program of China(No.2023YFB3407003)the National Natural Science Foundation of China(No.52375378).
文摘A new analytical model for geometric size and forming force prediction in incremental flanging(IF)is presented in this work.The complex deformation characteristics of IF are considered in the modeling process,which can accurately describe the strain and stress states in IF.Based on strain analysis,the model can predict the material thickness distribution and neck height after IF.By considering contact area,strain characteristics,material thickness changes,and friction,the model can predict specific moments and corresponding values of maximum axial forming force and maximum horizontal forming force during IF.In addition,an IF experiment involving different tool diameters,flanging diameters,and opening hole diameters is conducted.On the basis of the experimental strain paths,the strain characteristics of different deformation zones are studied,and the stable strain ratio is quantitatively described through two dimensionless parameters:relative tool diameter and relative hole diameter.Then,the changing of material thickness and forming force in IF,and the variation of minimum material thickness,neck height,maximum axial forming force,and maximum horizontal forming force with flanging parameters are studied,and the reliability of the analytical model is verified in this process.Finally,the influence of the horizontal forming force on the tool design and the fluctuation of the forming force are explained.
基金supported by the Key R&D Program of Zhejiang Province(Nos.2023C01166 and 2024SJCZX0046)the Zhejiang Provincial Natural Science Foundation of China(Nos.LDT23E05013E05 and LD24E050009)the Natural Science Foundation of Ningbo(No.2021J150),China.
文摘Accuracy allocation is crucial in the accuracy design of machining tools.Current accuracy allocation methods primarily focus on positional deviation,with little consideration for tool direction deviation.To address this issue,we propose a geometric error cost sensitivity-based accuracy allocation method for five-axis machine tools.A geometric error model consisting of 4l error components is constructed based on homogeneous transformation matrices.Volumetric points with positional and tool direction deviations are randomly sampled to evaluate the accuracy of the machine tool.The sensitivity of each error component at these sampling points is analyzed using the Sobol method.To balance the needs of geometric precision and manufacturing cost,a geometric error cost sensitivity function is developed to estimate the required cost.By allocating error components affecting tool direction deviation first and the remaining components second,this allocation scheme ensures that both deviations meet the requirements.We also perform numerical simulation of a BC-type(B-axis and C-axis type)five-axis machine tool to validate the method.The results show that the new allocation scheme reduces the total geometric error cost by 27.8%compared to a uniform allocation scheme,and yields the same positional and tool direction machining accuracies.
基金supported by the National Natural Science Foundation of China(Grant Nos.12347104,U24A2017,12461160276,and 12175075)the National Key Research and Development Program of China(Grant No.2023YFC2205802)+1 种基金the Natural Science Foundation of Jiangsu Province(Grant Nos.BK20243060 and BK20233001)in part by the State Key Laboratory of Advanced Optical Communication Systems and Networks,China。
文摘The quantum geometric tensor(QGT)is a fundamental quantity for characterizing the geometric properties of quantum states and plays an essential role in elucidating various physical phenomena.The traditional QGT,defned only for pure states,has limited applicability in realistic scenarios where mixed states are common.To address this limitation,we generalize the defnition of the QGT to mixed states using the purifcation bundle and the covariant derivative.Notably,our proposed defnition reduces to the traditional QGT when mixed states approach pure states.In our framework,the real and imaginary parts of this generalized QGT correspond to the Bures metric and the mean gauge curvature,respectively,endowing it with a broad range of potential applications.Additionally,using our proposed mixed-state QGT,we derive the geodesic equation applicable to mixed states.This work establishes a unifed framework for the geometric analysis of both pure and mixed states,thereby deepening our understanding of the geometric properties of quantum states.
基金Supported by the Natural Science Foundation of Hubei Province(2021CFB275)National Natural Science Foundation of China(12301667).
文摘In this paper,we study the geometric ergodicity of continuous time Markov pro-cesses in general state space.For the geometric ergodic continuous time Markov processes,the condition π(f^(p))<∞,p>1 is added.Using the coupling method,we obtain the existence of a full absorbing set on which continuous time Markov processes are f-geometric ergodic.
基金Supported by Jiangsu Key R&D Program(BE2021622)Jiangsu Postgraduate Practice and Innovation Program(SJCX23_0395).
文摘Background As visual simultaneous localization and mapping(SLAM)is primarily based on the assumption of a static scene,the presence of dynamic objects in the frame causes problems such as a deterioration of system robustness and inaccurate position estimation.In this study,we propose a YGC-SLAM for indoor dynamic environments based on the ORB-SLAM2 framework combined with semantic and geometric constraints to improve the positioning accuracy and robustness of the system.Methods First,the recognition accuracy of YOLOv5 was improved by introducing the convolution block attention model and the improved EIOU loss function,whereby the prediction frame converges quickly for better detection.The improved YOLOv5 was then added to the tracking thread for dynamic target detection to eliminate dynamic points.Subsequently,multi-view geometric constraints were used for re-judging to further eliminate dynamic points while enabling more useful feature points to be retained and preventing the semantic approach from over-eliminating feature points,causing a failure of map building.The K-means clustering algorithm was used to accelerate this process and quickly calculate and determine the motion state of each cluster of pixel points.Finally,a strategy for drawing keyframes with de-redundancy was implemented to construct a clear 3D dense static point-cloud map.Results Through testing on TUM dataset and a real environment,the experimental results show that our algorithm reduces the absolute trajectory error by 98.22%and the relative trajectory error by 97.98%compared with the original ORBSLAM2,which is more accurate and has better real-time performance than similar algorithms,such as DynaSLAM and DS-SLAM.Conclusions The YGC-SLAM proposed in this study can effectively eliminate the adverse effects of dynamic objects,and the system can better complete positioning and map building tasks in complex environments.
基金supported by the National Natural Science Foundation of China(Nos.92461313,12074387,and 92161114)the Innovation Capability Support Program of Shaanxi Province(No.2023-CX-TD-49).
文摘The structure and electronic properties of Co_(2)Ge_(10)^(-)anion and its neutral counterpart were investigated by anion photoelectron spectroscopy and theoretical calculations.The experimental vertical detachment energy of Co_(2)Ge_(10)^(-)was measured to be 2.86±0.08 eV.The lowest-energy isomer of Co_(2)Ge_(10)^(-)is in a doublet state and has a cage-like structure with Cs symmetry,which can be constructed by a tetragonal bipyramid on top of a pentagonal bipyramid and these two bipyramid structures share a common Co atom.The most stable structure of neutral Co_(2)Ge_(10)resembles its anionic counterpart and it is in a triplet state.The natural population analysis showed that the inner Co atom of both the anionic and neutral Co_(2)Ge_(10)acquires negative charge from the neighboring Ge atoms.The outer Co atom has a larger spin moment than the inner Co atom,indicating that the magnetic moments of Co_(2)Ge_(10)^(-/0)are mainly contributed by the outer Co atom.Analyses of the density of states and molecular orbitals indicated that there are a few highly delocalized molecular orbitals in Co_(2)Ge_(10)^(-),which are mainly contributed by Ge 4s atomic orbitals.
基金Supported by the Higher Education Science Research Project(Natural Science)of Anhui Province(Grant No.2023AH050487)。
文摘In this paper,we introduce a new geometric constant R_(X)(κ)based on isosceles orthogonality.First,we explore some basic properties of this new constant and then provide several examples to estimate its exact values in certain specific Banach spaces.Next,we investigate the relationships between this new constant and other classical constants.Specifically,we establish an inequality relationship between it and the J(X)constant,as well as an identity relationship between it and theρX(t)constant.Furthermore,we characterize some geometric properties of Banach spaces by means of this new constant.Finally,by restricting the above-mentioned constant to the unit sphere,we introduce another new constant,calculate its upper and lower bounds,and present a relevant example.
文摘This paper investigates the development and performance of a new higher-order geometric stiffness matrix that more closely approximates the theoretically derived stiffness coefficients.Factors that influence the accuracy of the solution are studied using two columns,two braced frames,and one unbraced frame.Discussion is provided when the new geometric stiffness matrix can be used to improve the buckling load analysis results and when it may provide only nominal additional benefit.
