During horizontal well drilling,the interaction between drilling fluid and cuttings entering the annulus generates diverse flow patterns.These solid-liquid two-phase flow patterns must be accurately predicted to optim...During horizontal well drilling,the interaction between drilling fluid and cuttings entering the annulus generates diverse flow patterns.These solid-liquid two-phase flow patterns must be accurately predicted to optimize the determination of hydraulic parameters and improve the efficiency of cuttings transport.Accordingly,this study identified flow patterns and conducted transition experiments under different inclination angles using a visualized wellbore annulus apparatus(120 mm outer diameter/73 mm inner diameter).Through direct visual observations,four primary flow patterns were systematically classified on the basis of the solid-liquid two-phase flow behaviors identified in the experiments:stable bed(SB),sand wave(SW),sand dune(SD),and bed load(BL)flows.The experimental data were then used to construct flow pattern maps with solid/liquid phases as axes,after which the transition boundaries between different flow patterns were established.The morphological characteristics and transition mechanisms of SB,SW,SD,and BL flows were systematically analyzed to develop three predictive models of the fluid dynamics principles governing these flow patterns’transitions:(1)A transition boundary model of SB and SW flows was established using Kelvin-Helmholtz stability,for which a stability analysis of solid-liquid two-phase flow in deviated and horizontal annuli was carried out.(2)A transition boundary model of SW and SD flows was constructed through an analysis of the geometric features of sand waves in the annuli,with the critical ratio of the average height of a cuttings bed to its height after erosion being 0.45.(3)A traditional critical velocity model was refined by adjusting the von Karman constant to account for the effect of solid volume concentration,yielding a boundary model for the transition of SW or SD flow into BL flow.All the models were experimentally validated.Finally,we integrated the models to develop a unified method for identifying and classifying the patterns typifying solid-liquid two-phase flow in deviated and horizontal annuli.展开更多
As lithium-ion batteries(LIBs)continue to evolve toward lower costs and higher energy densities,their potential safety risks have become increasingly apparent.Incidents such as explosions at energy storage facilities,...As lithium-ion batteries(LIBs)continue to evolve toward lower costs and higher energy densities,their potential safety risks have become increasingly apparent.Incidents such as explosions at energy storage facilities,fires in electric vehicles,and building fires ignited by charging two-wheeled vehicles have been occurring with alarming frequency,often resulting in significant casualties and injuries.Conducting indepth investigations into thermal runaway(TR)incidents in LIBs can significantly reduce the risk of future occurrences.However,current investigations into LIB fire and explosion incidents face challenges due to the difficulty of conducting in-depth analyses and the lack of a robust theoretical framework to guide these investigations.To enhance the effectiveness of in-depth investigations into battery fire and explosion incidents and to address the lack of theoretical guidance,this paper is the first to systematically examine the conservation and flow patterns of elements during the TR process of LIBs.The analysis reveals that during TR,the gas products generated include approximately 1.5 g of H_(2),23.6 g of CO,88.4 g of CO_(2),8.9 g of C_(2)H_(4),7.3 g of CH_(4),3.7 g of C_(2)H_(6),and 82 g of electrolyte vapor.After TR,the solid compounds formed consist of approximately 2.5 g of LiF,29–92.2 g of elemental Ni/Co/Mn,11.4 g of Li_(2)CO_(3),200.6 g of graphite,1.4 g of NiO,29.6 g of MnO,30.1 g of CoO,67 g of elemental Cu,0.03 g of LiNiO_(2),and 4.3 g of LiAlO_(2).Importantly,the energy released from reactions forming solid compounds during TR surpasses that from gas-forming reactions.This investigation represents the first application of Hess’s law to verify the conservation of elements during the TR process of lithium-ion batteries.The proposed methodology is also applicable to other types of energy storage batteries,effectively advancing techniques for comprehensively investigating lithium battery fire and explosion incidents.展开更多
The flow patterns in the inlet and outlet conduits have a decisive effect on the safe, stable, and highly efficient operation of the pump in a large pumping station with low head. The numerical simulation of three-dim...The flow patterns in the inlet and outlet conduits have a decisive effect on the safe, stable, and highly efficient operation of the pump in a large pumping station with low head. The numerical simulation of three-dimensional （3D） turbulence flow in conduits is an important method to study the hydraulic performance and conduct an optimum hydraulic design for the conduits. With the analyses of the flow patterns in the inlet and outlet conduits, the boundary conditions of the numerical simulation for them can be determined. The main obtained conclusions are as follows： （i） Under normal operation conditions, there is essentially no pre-swirl flow at the impeller chamber inlet of an axial-flow pump system, based on which the boundary condition at the inlet conduit may be defined. （ii） The circulation at the guide vane outlet of an axial-flow pump system has a great effect on the hydraulic performance of the outlet conduit, and there is optimum circulation for the performance. Therefore, it is strongly suggested to design the guide vane according to the optimum circulation. （iii） The residual circulation at the guide vane outlet needs to be considered for the inlet boundary condition of the outlet conduit, and the value of the circulation may be measured in a specially designed test model.展开更多
Bends are widely used in pipelines carrying single-and two-phase fluids in both ground and space applications.In particular,they play more important role in space applications due to the extreme spatial constraints.In...Bends are widely used in pipelines carrying single-and two-phase fluids in both ground and space applications.In particular,they play more important role in space applications due to the extreme spatial constraints.In the present study,a set of experimental data of two-phase flow patterns and their transitions in a 90°bend with inner diameter of 12.7 mm and curvature radius of 76.5 mm at microgravity conditions are reported.Gas and liquid superficial velocities are found to range from (1.0～23.6)m/s for gas and(0.09～0.5)m/s for liquid,respectively.Three major flow patterns, namely slug,slug-annular transitional,and annular flows,are observed in this study.Focusing on the differences between flow patterns in bends and their counterparts in straight pipes,detailed analyses of their characteristics are made.The transitions between adjoining flow patterns are found to be more or less the same as those in straight pipes,and can be predicted using Weber number models satisfactorily. The reasons for such agreement are carefully examined.展开更多
In this companion paper, flow patterns in the upstream and downstream tubes of a sudden-expansion cross-section (SECS) in a vertical straight pipe were presented. The effect of SECS on flow patterns upstream and down...In this companion paper, flow patterns in the upstream and downstream tubes of a sudden-expansion cross-section (SECS) in a vertical straight pipe were presented. The effect of SECS on flow patterns upstream and downstream was analyzed by comparing with flow patterns in uniform cross-section vertical tubes. It is found the effect is great. There exist great instabilities of two-phase flow in the neighboring areas of the SECS both downstream and upstream.展开更多
Effects of the flow pattern of intertubular liquid film on mass and heat transfer synergies in a falling-film dehumidification system with horizontal pipes are studied.A flow model of the dehumidifying solution betwee...Effects of the flow pattern of intertubular liquid film on mass and heat transfer synergies in a falling-film dehumidification system with horizontal pipes are studied.A flow model of the dehumidifying solution between horizontal pipes is established using Fluent software,the rule of transitions of the flow pattern between pipes is studied,critical Reynolds numbers of flow pattern transitions are obtained,and the accuracy of the model is verified by experiments.The mass transfer synergy angle and heat transfer synergy angle are respectively used as evaluation criteria for the mass transfer synergy and heat transfer synergy,and distribution laws of the synergy angles for droplet,droplet columnar and curtain flow patterns are obtained.Simulation results show that the mass transfer synergy angles corresponding to droplet,droplet columnar and curtain flow patterns all rise to a plateau with time.The mean mass-transfer synergy angle is 98°for the droplet flow pattern,higher than 96.5°for the droplet columnar flow pattern and 95°for the curtain flow pattern.The results show that the mass transfer synergy of the droplet flow pattern is better than that of the droplet columnar flow pattern and that of the curtain flow pattern.展开更多
Flow patterns upstream and downstream of a sudden-contraction cross-section in a vertical straight pipe were presented. By comparing with flow patterns in uniform cross-section vertical tubes, the effect of the sudde...Flow patterns upstream and downstream of a sudden-contraction cross-section in a vertical straight pipe were presented. By comparing with flow patterns in uniform cross-section vertical tubes, the effect of the sudden change in pipe diameter on flow patterns was analyzed. Flow pattern transition mechanisms were discussed and transition criteria for flow pattern transitions were deduced accordingly using the dimensional analysis.展开更多
The World Journal of Cardiology published an article written by Kuwahara et al that we take the pleasure to comment on.We focused our attention on venous congestion.In intensive care settings,it is now widely accepted...The World Journal of Cardiology published an article written by Kuwahara et al that we take the pleasure to comment on.We focused our attention on venous congestion.In intensive care settings,it is now widely accepted that venous congestion is an important clinical feature worthy of investigation.Evaluating venous Doppler profile abnormalities at multiple sites could suggest adequate treatment and monitor its efficacy.Renal dysfunction could trigger or worsen fluid overload in heart disease,and cardio-renal syndrome is a well-characterized spectrum of disorders describing the complex interactions between heart and kidney diseases.Fluid overload and venous congestion,including renal venous hypertension,are major determinants of acute and chronic renal dysfunction arising in heart disease.Organ congestion from venous hypertension could be involved in the development of organ injury in several clinical situations,such as critical diseases,congestive heart failure,and chronic kidney disease.Ultrasonography and abnormal Doppler flow patterns diagnose clinically significant systemic venous congestion.Cardiologists and nephrologists might use this valuable,noninvasive,bedside diagnostic tool to establish fluid status and guide clinical choices.展开更多
Objective： To evaluate the efficacy of dynamic multi-slice spiral computed tomography （MSCT） for providing quantitative information about blood flow patterns of solitary pulmonary nodules （SPNs）. Methods： Sevent...Objective： To evaluate the efficacy of dynamic multi-slice spiral computed tomography （MSCT） for providing quantitative information about blood flow patterns of solitary pulmonary nodules （SPNs）. Methods： Seventy-eight patients with SPNs （diameter 〈 4 cm; 68 malignant; 10 active inflammatory） were underwent multi-location dynamic contrast material-enhanced serial CT （nonionic contrast material was administrated via the antecubital vein at a rate of 4 mLJs by using an autoinjector, 4 × 5 mm or 4 × 2.5 mm transverse scanning mode with stable table were performed）. Sixteen series CT scans （16 scans each for the first and second series and one scan each for the rest series） were obtained during 9 min scanning period. Precontrast and postcontrast attenuation on every scan was recorded. Perfusion, peak height and ratio of peak height of the SPN to that of the aorta were calculated. Perfusion was calculated from the maximum gradient of the time-attenuation curve and the peak height of the aorta. Results： No statistically significant difference in the peak height was found between malignant （35.79 ± 10.76 Hu） and active inflammatory （39.76 ± 4.59 Hu） （t = 1.148, P = 0.255 〉 0.05）. SPN-to-aorta ratio （14.27% ± 4.37） and perfusion value （30.18 mL/min/100 g ± 9.58） in malignant SPNs were significantly lower than those of active inflammatory （18.51% ± 2.71, 63.44 mL/min/100 g ± 43.87） （t = 2.978, P = 0.004 〈 0.05; t = 5.590, P 〈 0.0001）. Conclusion： The quantitative information about blood flow patterns of malignant and active inflammatory SPNs is different. SPN-to-aorta ratio and perfusion value are helpful in differentiating malignant nodules from active inflammatory.展开更多
A water model and a high-speed video camera were utilized in the 300-t RH equipment to study the effect of steel flow patterns in a vacuum chamber on fast decarburization and a superior flow-pattern map was obtained d...A water model and a high-speed video camera were utilized in the 300-t RH equipment to study the effect of steel flow patterns in a vacuum chamber on fast decarburization and a superior flow-pattern map was obtained during the practical RH process. There are three flow patterns with different bubbling characteristics and steel surface states in the vacuum chamber： boiling pattern（BP）, transition pattern（TP）, and wave pattern（WP）. The effect of the liquid-steel level and the residence time of the steel in the chamber on flow patterns and decarburization reaction were investigated, respectively. The liquid-steel level significantly affected the flow-pattern transition from BP to WP, and the residence time and reaction area were crucial to evaluate the whole decarburization process rather than the circulation flow rate and mixing time. A superior flow-pattern map during the practical RH process showed that the steel flow pattern changed from BP to TP quickly, and then remained as TP until the end of decarburization.展开更多
The mutual relationships of three effective factors, the diameter D/d （d is the diameter of exit） of obstructed plate, exit densimetric Froude number and the distance Hid of the plate from jet orifice for obstructed...The mutual relationships of three effective factors, the diameter D/d （d is the diameter of exit） of obstructed plate, exit densimetric Froude number and the distance Hid of the plate from jet orifice for obstructed buoyant jet in static ambient, are analyzed to explain normal and abnormal rounded flowing （reverberated and bifurcated flowing）. The critical Froude numbers for obstructed buoyant jets with H/d=2, 4, 6, 8 which distinguished normal and abnormal flowing pattern are obtained. Normal rounded flowing is found only for a plate under a special value of H/d. A fitted formula of critical Froude numbers with H/d and D/d is presented to distinguish rounded flowing types. The occurring of reverberated or bifurcated flowing in abnormal rounded flow is analyzed. Based on the results of obstructed buoyant jets with D/d=1, normal rounded flowing occurred only for all conditions and axial dilution behind the plate under different H/D is obtained.展开更多
The flow patterns of Euro-Atlantic blocking events in winter are investigated by dividing the sector into three sub- regions： 60°-30°W （Greenland region）; 20°W-30°E [eastern Atlantic-Europe （EA...The flow patterns of Euro-Atlantic blocking events in winter are investigated by dividing the sector into three sub- regions： 60°-30°W （Greenland region）; 20°W-30°E [eastern Atlantic-Europe （EAE） region]; and 50°-90°E （Ural region）. It is shown that blocking events in winter are extremely frequent in the three sub-regions. Composite 500-mb geopotential height fields for intense and long-lived blocking events demonstrate that the blocking fields over Greenland and Ural regions exhibit southwest-northeast （SW-NE） and southeast-northwest （SE-NW） oriented dipole-type patterns, respectively, while the composite field over the EAE region exhibits an Ω-type pattern. The type of composite blocking pattern seems to be related to the position of the blocking region relative to the positive center of the climatological stationary wave （CSW） anomaly existing near 10°W. The physical cause of why there are different composite blocking types in the three sub-regions is identified using a nonlinear multiscale interaction model. It is found that when the blocking event is in almost the same position as the positive CSW anomaly, the planetary-scale field can exhibit an Ω-type pattern due to the enhanced positive CSW anomaly. Neverthe- less, a SW-NE （SE-NW） oriented dipole-type block can occur due to the reduced positive CSW anomaly as it is farther in the west （east） of the positive CSW anomaly. The total fields of blocking in the three regions may exhibit a meandering flow comprised of several isolated anticyclonic and cyclonic vortices, which resembles the Berggren-Bolin-Rossby meandering jet type.展开更多
Pulsatile blood flows in curved atherosclerotic arteries are studied by computer simulations. Computations are carried out with various values of physiological parameters to examine the effects of flow parameters on t...Pulsatile blood flows in curved atherosclerotic arteries are studied by computer simulations. Computations are carried out with various values of physiological parameters to examine the effects of flow parameters on the disturbed flow patterns downstream of a curved artery with a stenosis at the inner wall. The numerical results indicate a strong dependence of flow pattern on the blood viscosity and inlet flow rate, while the influence of the inlet flow profile to the flow pattern in downstream is negligible.展开更多
The hemodynamics of intracranial aneurysm(IA)comprises complex transient flow patterns that affect its growth and rupture.Owing to the combined effects of geometrical factors and pulsatile flow conditions,the transien...The hemodynamics of intracranial aneurysm(IA)comprises complex transient flow patterns that affect its growth and rupture.Owing to the combined effects of geometrical factors and pulsatile flow conditions,the transient flow patterns in the IA are still unclear.The purpose of this work is to reveal the effect of the aspect ratio(AR,sac height/neck width)on the evolution of the internal flow patterns and the hemodynamics of the IA.We proposed an easy method to fabricate three simplified elastic IA models and measured the transient flow characteristics by using particle image velocimetry(PIV).Transient vortex structures in the IA modes during a cardiac cycle were systemically measured and many new flow phenomena were found,including the vortex morphology(size,structure,and core location),a high-speed jet,wall compliance effects,and three flow modes during retrograde flow phase.The results show that the AR of the IA affects the transient flow patterns as well as the wall shear stress(WSS)in complex ways.The results could deepen our understanding of the transient flow behaviors in IA and guide related clinical studies.展开更多
Studies on the high-lift mechanisms of butterfly gliding flights shed light on the design of the micro air vehicles.The flow field around a simplified Danaus plexippus model is investigated using the hydrogen bubble v...Studies on the high-lift mechanisms of butterfly gliding flights shed light on the design of the micro air vehicles.The flow field around a simplified Danaus plexippus model is investigated using the hydrogen bubble visualization and the Particle Image Velocimetry(PIV)techniques.There are three near-wall topological patterns with different Angles of Attack(AoAs):the separation bubble,the Leading-Edge Vortex(LEV)and the high Ao As flow.For the separation bubble pattern,two saddles and two foci form in the middle of the model.The features of the LEV pattern are the leading-edge separation lines.The topological characteristics of the separation lines are changed by the interaction between the LEV and the Wing-Tip Vortex(WTV).For the high Ao As flow pattern,four unstable foci are found at the forewing and the hindwing respectively.The angle between the trajectory of the WTV and the model increases with increasing Ao A even though the slope of the WTV angle versus Ao A curve declines at the moderate AoAs.展开更多
The impact of thermal conditions of the ground on ventilation in the interior courtyard and rooms of enclosed building is very important to improve the air quality in courtyard. The computational fluid dynamics( CFD) ...The impact of thermal conditions of the ground on ventilation in the interior courtyard and rooms of enclosed building is very important to improve the air quality in courtyard. The computational fluid dynamics( CFD) model was used to investigate the flow field of a certain courtyard and analyze the static differential pressure between the two sides of the vent and ventilation conditions of the courtyard. The results indicate that thermal effects not only changed the air flow pattern of the interior courtyard but also obviously increased the flow velocity of the upper space of the courtyard. For the most of courtyard rooms,the absolute value of static differential pressure increases as the thermal intensity of the ground increases. In all wind directions,the air exchange rate of the courtyard increases with the higher thermal intensity of the ground which makes a greater influence on the increasing of the ventilation rate of the roof opening than that on the gate opening.展开更多
Hilly terrain pipeline is a common form of pipeline in oil and gas storage and transportation industry.Due to the hilly terrain influence, the liquid at the elbow of the gathering pipeline is easy to flow back and acc...Hilly terrain pipeline is a common form of pipeline in oil and gas storage and transportation industry.Due to the hilly terrain influence, the liquid at the elbow of the gathering pipeline is easy to flow back and accumulate to form slug flow, so it is necessary to remove the accumulated liquid by gas purging. In this paper, experiment is carried out in hilly terrain pipelines. Three flow patterns of stratified flow, slug flow and stratified entrained flow are observed. The process of gas purging accumulated liquid is divided into four stages, namely liquid accumulation, liquid rising, continuous outflow and tail outflow. At the same time, the flow pattern maps of each stage are drawn. The pressure drop signal is analyzed in time domain and frequency domain, and the contour map of pressure drop distribution is drawn. It is found that the ratio of range to average value can well distinguish the occurrence range of each flow pattern.Based on visualization, the transition process of slug flow to stratified flow and stratified entrained flow is studied, and the transition boundary prediction model is established. An image processing method is proposed to convert the image signal into a similarity curve, and PSD analysis is performed to calculate the slug frequency. The normal distribution is used to fit the slug frequency, and the predicted correlation is in good agreement with the experimental data.展开更多
Intracranial aneurysm(IA)is a prevalent cerebrovascular disease associated with high mortality and disability rates upon rupture.The hemodynamics of IA,which are significantly influenced by geometric parameters,direct...Intracranial aneurysm(IA)is a prevalent cerebrovascular disease associated with high mortality and disability rates upon rupture.The hemodynamics of IA,which are significantly influenced by geometric parameters,directly impact its rupture.This study focuses on investigating the transient flow characteristics in saccular IA models fabricated using a water droplet-based method,specifically examining the influence of neck widths.Particle image velocimetry technique and numerical simulation were employed to investigate the dynamic evolution of flow structures within three IA models.The results reveal that neck width(W)has a substantial effect on flow characteristics in the neck region,subsequently impacting the deep flow inside the sac.Three distinct patterns were observed during flow evolution inside the sac:for W=2 mm,two vortices occur and then disappear with relatively low average flow velocity;for W=4 mm,enhanced effects of a high-speed jet result in periodic pulsatile flow velocity distribution while maintaining stable vortex core position;for W=6 mm,significant changes in flow velocity occur due to size expansion and intensity increase of vortices.These findings demonstrate that neck widths play a complex role in influencing transient flow characteristics within IAs.Overall,this research contributes to further understanding transient flow behaviors in IAs.展开更多
The hydrogen-enriched direct reduction shaft furnace addresses the high CO_(2) emissions associated with the blast furnace process.A discrete element method(DEM)model was introduced to explore how the structure of the...The hydrogen-enriched direct reduction shaft furnace addresses the high CO_(2) emissions associated with the blast furnace process.A discrete element method(DEM)model was introduced to explore how the structure of the diversion cone affects particle descent behavior in a hydrogen-enriched shaft furnace.The results indicated that in the absence of a diversion cone,the descending velocity near the furnace wall zone is significantly lower than that at its center,resulting in a‘V’-shaped burden flow pattern.The discharge velocity has a minor impact on the flow pattern in the shaft furnace.Upon installation of a diversion cone,burden descending velocity becomes more uniform,leading to a‘-’-shaped burden flow pattern.As the bottom of the diversion cone ascends(i.e.,the lower end of the diversion cone is progressively closer to the top),there is an increase in the volume fraction of the dead zone within the shaft furnace.This is particularly evident in the formation of a triangular dead zone at the base of the diversion cone.It is suggested that the lower cone of the bi-conical diversion cone should maintain a sufficient height.展开更多
This research explores the characteristics of boiling in inclined pipes,a domain of great importance in engineering.Employing an experimental visualization technique,the boiling dynamics of deionizedwater are examined...This research explores the characteristics of boiling in inclined pipes,a domain of great importance in engineering.Employing an experimental visualization technique,the boiling dynamics of deionizedwater are examined at varying inclination angles,paying special attention to the emerging flow patterns.The findings demonstrate that the inclination angle significantly impacts flow pattern transitions within the 0°to 90°range.As the heat flux rises,bubbles form in the liquid.The liquid’s inertia extends the bubble-wall contact time,thereby delaying the onset of bulk bubble flow.Beyond a 90°inclination,however,the patterning behavior is more influenced by the fluid velocity.At low speeds,incomplete pipe filling results in a large liquid plug hindering flow,while high speeds lead to full pipe filling.In general,gravity,inertia,buoyancy forces,and capillary forces are themain influential factors in the considered problem.However,an analysis of the heat transfer coefficient and boiling curve for different inclination angles reveals that the observed variations are essentially due to corresponding changes in the flow pattern.Finally,an optimal mass flux and inclination angle,able to minimize total entropy generation and improve heat transfer efficiency,are determined by means of an entropy generation analysis.展开更多
基金sponsored by the National Natural Science Foundation of China(Nos.52174002&52204008)the Heilongjiang Provincial Natural Science Foundation of China(No.LH2022E020).
文摘During horizontal well drilling,the interaction between drilling fluid and cuttings entering the annulus generates diverse flow patterns.These solid-liquid two-phase flow patterns must be accurately predicted to optimize the determination of hydraulic parameters and improve the efficiency of cuttings transport.Accordingly,this study identified flow patterns and conducted transition experiments under different inclination angles using a visualized wellbore annulus apparatus(120 mm outer diameter/73 mm inner diameter).Through direct visual observations,four primary flow patterns were systematically classified on the basis of the solid-liquid two-phase flow behaviors identified in the experiments:stable bed(SB),sand wave(SW),sand dune(SD),and bed load(BL)flows.The experimental data were then used to construct flow pattern maps with solid/liquid phases as axes,after which the transition boundaries between different flow patterns were established.The morphological characteristics and transition mechanisms of SB,SW,SD,and BL flows were systematically analyzed to develop three predictive models of the fluid dynamics principles governing these flow patterns’transitions:(1)A transition boundary model of SB and SW flows was established using Kelvin-Helmholtz stability,for which a stability analysis of solid-liquid two-phase flow in deviated and horizontal annuli was carried out.(2)A transition boundary model of SW and SD flows was constructed through an analysis of the geometric features of sand waves in the annuli,with the critical ratio of the average height of a cuttings bed to its height after erosion being 0.45.(3)A traditional critical velocity model was refined by adjusting the von Karman constant to account for the effect of solid volume concentration,yielding a boundary model for the transition of SW or SD flow into BL flow.All the models were experimentally validated.Finally,we integrated the models to develop a unified method for identifying and classifying the patterns typifying solid-liquid two-phase flow in deviated and horizontal annuli.
基金supported by the National Natural Science Foundation of China(52106284,52422609)the Natural Science Foundation of Hebei Province(B2021507001)Key Research Special Project of CPPU(ZDZX202501)。
文摘As lithium-ion batteries(LIBs)continue to evolve toward lower costs and higher energy densities,their potential safety risks have become increasingly apparent.Incidents such as explosions at energy storage facilities,fires in electric vehicles,and building fires ignited by charging two-wheeled vehicles have been occurring with alarming frequency,often resulting in significant casualties and injuries.Conducting indepth investigations into thermal runaway(TR)incidents in LIBs can significantly reduce the risk of future occurrences.However,current investigations into LIB fire and explosion incidents face challenges due to the difficulty of conducting in-depth analyses and the lack of a robust theoretical framework to guide these investigations.To enhance the effectiveness of in-depth investigations into battery fire and explosion incidents and to address the lack of theoretical guidance,this paper is the first to systematically examine the conservation and flow patterns of elements during the TR process of LIBs.The analysis reveals that during TR,the gas products generated include approximately 1.5 g of H_(2),23.6 g of CO,88.4 g of CO_(2),8.9 g of C_(2)H_(4),7.3 g of CH_(4),3.7 g of C_(2)H_(6),and 82 g of electrolyte vapor.After TR,the solid compounds formed consist of approximately 2.5 g of LiF,29–92.2 g of elemental Ni/Co/Mn,11.4 g of Li_(2)CO_(3),200.6 g of graphite,1.4 g of NiO,29.6 g of MnO,30.1 g of CoO,67 g of elemental Cu,0.03 g of LiNiO_(2),and 4.3 g of LiAlO_(2).Importantly,the energy released from reactions forming solid compounds during TR surpasses that from gas-forming reactions.This investigation represents the first application of Hess’s law to verify the conservation of elements during the TR process of lithium-ion batteries.The proposed methodology is also applicable to other types of energy storage batteries,effectively advancing techniques for comprehensively investigating lithium battery fire and explosion incidents.
基金Project supported by the Natural Science Foundation of Jiangsu Higher Education Institutions ofChina(No.12KJD570001)
文摘The flow patterns in the inlet and outlet conduits have a decisive effect on the safe, stable, and highly efficient operation of the pump in a large pumping station with low head. The numerical simulation of three-dimensional （3D） turbulence flow in conduits is an important method to study the hydraulic performance and conduct an optimum hydraulic design for the conduits. With the analyses of the flow patterns in the inlet and outlet conduits, the boundary conditions of the numerical simulation for them can be determined. The main obtained conclusions are as follows： （i） Under normal operation conditions, there is essentially no pre-swirl flow at the impeller chamber inlet of an axial-flow pump system, based on which the boundary condition at the inlet conduit may be defined. （ii） The circulation at the guide vane outlet of an axial-flow pump system has a great effect on the hydraulic performance of the outlet conduit, and there is optimum circulation for the performance. Therefore, it is strongly suggested to design the guide vane according to the optimum circulation. （iii） The residual circulation at the guide vane outlet needs to be considered for the inlet boundary condition of the outlet conduit, and the value of the circulation may be measured in a specially designed test model.
基金The project supported by the Canadian Space Agency (CSA) and the visiting scholar program of the Chinese Academy of Sciences (CAS)
文摘Bends are widely used in pipelines carrying single-and two-phase fluids in both ground and space applications.In particular,they play more important role in space applications due to the extreme spatial constraints.In the present study,a set of experimental data of two-phase flow patterns and their transitions in a 90°bend with inner diameter of 12.7 mm and curvature radius of 76.5 mm at microgravity conditions are reported.Gas and liquid superficial velocities are found to range from (1.0～23.6)m/s for gas and(0.09～0.5)m/s for liquid,respectively.Three major flow patterns, namely slug,slug-annular transitional,and annular flows,are observed in this study.Focusing on the differences between flow patterns in bends and their counterparts in straight pipes,detailed analyses of their characteristics are made.The transitions between adjoining flow patterns are found to be more or less the same as those in straight pipes,and can be predicted using Weber number models satisfactorily. The reasons for such agreement are carefully examined.
基金the National Natural Science Foundation of China (No. 59236130).
文摘In this companion paper, flow patterns in the upstream and downstream tubes of a sudden-expansion cross-section (SECS) in a vertical straight pipe were presented. The effect of SECS on flow patterns upstream and downstream was analyzed by comparing with flow patterns in uniform cross-section vertical tubes. It is found the effect is great. There exist great instabilities of two-phase flow in the neighboring areas of the SECS both downstream and upstream.
基金Project(2016YFC0700100)supported by the National Key R&D Program of ChinaProject(JDJQ20160103)supported by the Promotion of the Connotation Development Quota Project of Colleges and Universities-Outstanding Youth of Architectural University,China。
文摘Effects of the flow pattern of intertubular liquid film on mass and heat transfer synergies in a falling-film dehumidification system with horizontal pipes are studied.A flow model of the dehumidifying solution between horizontal pipes is established using Fluent software,the rule of transitions of the flow pattern between pipes is studied,critical Reynolds numbers of flow pattern transitions are obtained,and the accuracy of the model is verified by experiments.The mass transfer synergy angle and heat transfer synergy angle are respectively used as evaluation criteria for the mass transfer synergy and heat transfer synergy,and distribution laws of the synergy angles for droplet,droplet columnar and curtain flow patterns are obtained.Simulation results show that the mass transfer synergy angles corresponding to droplet,droplet columnar and curtain flow patterns all rise to a plateau with time.The mean mass-transfer synergy angle is 98°for the droplet flow pattern,higher than 96.5°for the droplet columnar flow pattern and 95°for the curtain flow pattern.The results show that the mass transfer synergy of the droplet flow pattern is better than that of the droplet columnar flow pattern and that of the curtain flow pattern.
基金the National Natrual Science Foundation of China (No. 59236130).
文摘Flow patterns upstream and downstream of a sudden-contraction cross-section in a vertical straight pipe were presented. By comparing with flow patterns in uniform cross-section vertical tubes, the effect of the sudden change in pipe diameter on flow patterns was analyzed. Flow pattern transition mechanisms were discussed and transition criteria for flow pattern transitions were deduced accordingly using the dimensional analysis.
文摘The World Journal of Cardiology published an article written by Kuwahara et al that we take the pleasure to comment on.We focused our attention on venous congestion.In intensive care settings,it is now widely accepted that venous congestion is an important clinical feature worthy of investigation.Evaluating venous Doppler profile abnormalities at multiple sites could suggest adequate treatment and monitor its efficacy.Renal dysfunction could trigger or worsen fluid overload in heart disease,and cardio-renal syndrome is a well-characterized spectrum of disorders describing the complex interactions between heart and kidney diseases.Fluid overload and venous congestion,including renal venous hypertension,are major determinants of acute and chronic renal dysfunction arising in heart disease.Organ congestion from venous hypertension could be involved in the development of organ injury in several clinical situations,such as critical diseases,congestive heart failure,and chronic kidney disease.Ultrasonography and abnormal Doppler flow patterns diagnose clinically significant systemic venous congestion.Cardiologists and nephrologists might use this valuable,noninvasive,bedside diagnostic tool to establish fluid status and guide clinical choices.
文摘Objective： To evaluate the efficacy of dynamic multi-slice spiral computed tomography （MSCT） for providing quantitative information about blood flow patterns of solitary pulmonary nodules （SPNs）. Methods： Seventy-eight patients with SPNs （diameter 〈 4 cm; 68 malignant; 10 active inflammatory） were underwent multi-location dynamic contrast material-enhanced serial CT （nonionic contrast material was administrated via the antecubital vein at a rate of 4 mLJs by using an autoinjector, 4 × 5 mm or 4 × 2.5 mm transverse scanning mode with stable table were performed）. Sixteen series CT scans （16 scans each for the first and second series and one scan each for the rest series） were obtained during 9 min scanning period. Precontrast and postcontrast attenuation on every scan was recorded. Perfusion, peak height and ratio of peak height of the SPN to that of the aorta were calculated. Perfusion was calculated from the maximum gradient of the time-attenuation curve and the peak height of the aorta. Results： No statistically significant difference in the peak height was found between malignant （35.79 ± 10.76 Hu） and active inflammatory （39.76 ± 4.59 Hu） （t = 1.148, P = 0.255 〉 0.05）. SPN-to-aorta ratio （14.27% ± 4.37） and perfusion value （30.18 mL/min/100 g ± 9.58） in malignant SPNs were significantly lower than those of active inflammatory （18.51% ± 2.71, 63.44 mL/min/100 g ± 43.87） （t = 2.978, P = 0.004 〈 0.05; t = 5.590, P 〈 0.0001）. Conclusion： The quantitative information about blood flow patterns of malignant and active inflammatory SPNs is different. SPN-to-aorta ratio and perfusion value are helpful in differentiating malignant nodules from active inflammatory.
基金financially supported by the National Natural Science Foundation of China (No.51704203)the PhD Early Development Program of Taiyuan University of Science and Technology (Nos. 20152008, 20152013, and 20152018)+2 种基金Shanxi Province Science Foundation for Youths (No. 201601D202027)Key Project of Research and Development Plan of Shanxi Province (Nos. 201603D111004 and 201603D121010)NSFC-Shanxi Coal Based Low Carbon Joint Fund (No. U1510131)
文摘A water model and a high-speed video camera were utilized in the 300-t RH equipment to study the effect of steel flow patterns in a vacuum chamber on fast decarburization and a superior flow-pattern map was obtained during the practical RH process. There are three flow patterns with different bubbling characteristics and steel surface states in the vacuum chamber： boiling pattern（BP）, transition pattern（TP）, and wave pattern（WP）. The effect of the liquid-steel level and the residence time of the steel in the chamber on flow patterns and decarburization reaction were investigated, respectively. The liquid-steel level significantly affected the flow-pattern transition from BP to WP, and the residence time and reaction area were crucial to evaluate the whole decarburization process rather than the circulation flow rate and mixing time. A superior flow-pattern map during the practical RH process showed that the steel flow pattern changed from BP to TP quickly, and then remained as TP until the end of decarburization.
基金Project supported by the National Natural Science Foundation of China (No.50479038)
文摘The mutual relationships of three effective factors, the diameter D/d （d is the diameter of exit） of obstructed plate, exit densimetric Froude number and the distance Hid of the plate from jet orifice for obstructed buoyant jet in static ambient, are analyzed to explain normal and abnormal rounded flowing （reverberated and bifurcated flowing）. The critical Froude numbers for obstructed buoyant jets with H/d=2, 4, 6, 8 which distinguished normal and abnormal flowing pattern are obtained. Normal rounded flowing is found only for a plate under a special value of H/d. A fitted formula of critical Froude numbers with H/d and D/d is presented to distinguish rounded flowing types. The occurring of reverberated or bifurcated flowing in abnormal rounded flow is analyzed. Based on the results of obstructed buoyant jets with D/d=1, normal rounded flowing occurred only for all conditions and axial dilution behind the plate under different H/D is obtained.
基金the support from the National Science Foundation of China(Grant No.41375067) "One-Hundred Talents Plan"of the Chinese Academy of Sciences(Grant No.Y163011)
文摘The flow patterns of Euro-Atlantic blocking events in winter are investigated by dividing the sector into three sub- regions： 60°-30°W （Greenland region）; 20°W-30°E [eastern Atlantic-Europe （EAE） region]; and 50°-90°E （Ural region）. It is shown that blocking events in winter are extremely frequent in the three sub-regions. Composite 500-mb geopotential height fields for intense and long-lived blocking events demonstrate that the blocking fields over Greenland and Ural regions exhibit southwest-northeast （SW-NE） and southeast-northwest （SE-NW） oriented dipole-type patterns, respectively, while the composite field over the EAE region exhibits an Ω-type pattern. The type of composite blocking pattern seems to be related to the position of the blocking region relative to the positive center of the climatological stationary wave （CSW） anomaly existing near 10°W. The physical cause of why there are different composite blocking types in the three sub-regions is identified using a nonlinear multiscale interaction model. It is found that when the blocking event is in almost the same position as the positive CSW anomaly, the planetary-scale field can exhibit an Ω-type pattern due to the enhanced positive CSW anomaly. Neverthe- less, a SW-NE （SE-NW） oriented dipole-type block can occur due to the reduced positive CSW anomaly as it is farther in the west （east） of the positive CSW anomaly. The total fields of blocking in the three regions may exhibit a meandering flow comprised of several isolated anticyclonic and cyclonic vortices, which resembles the Berggren-Bolin-Rossby meandering jet type.
文摘Pulsatile blood flows in curved atherosclerotic arteries are studied by computer simulations. Computations are carried out with various values of physiological parameters to examine the effects of flow parameters on the disturbed flow patterns downstream of a curved artery with a stenosis at the inner wall. The numerical results indicate a strong dependence of flow pattern on the blood viscosity and inlet flow rate, while the influence of the inlet flow profile to the flow pattern in downstream is negligible.
基金supported by the National Natural Science Foundation of China(Grant Nos:12172017 and 11872083)Project of Beijing Municipal Education Commission(Grant Nos.KZ202210005006 and KZ202110005007).
文摘The hemodynamics of intracranial aneurysm(IA)comprises complex transient flow patterns that affect its growth and rupture.Owing to the combined effects of geometrical factors and pulsatile flow conditions,the transient flow patterns in the IA are still unclear.The purpose of this work is to reveal the effect of the aspect ratio(AR,sac height/neck width)on the evolution of the internal flow patterns and the hemodynamics of the IA.We proposed an easy method to fabricate three simplified elastic IA models and measured the transient flow characteristics by using particle image velocimetry(PIV).Transient vortex structures in the IA modes during a cardiac cycle were systemically measured and many new flow phenomena were found,including the vortex morphology(size,structure,and core location),a high-speed jet,wall compliance effects,and three flow modes during retrograde flow phase.The results show that the AR of the IA affects the transient flow patterns as well as the wall shear stress(WSS)in complex ways.The results could deepen our understanding of the transient flow behaviors in IA and guide related clinical studies.
基金funded by the National Natural Science Foundation of China (No. 11721202)。
文摘Studies on the high-lift mechanisms of butterfly gliding flights shed light on the design of the micro air vehicles.The flow field around a simplified Danaus plexippus model is investigated using the hydrogen bubble visualization and the Particle Image Velocimetry(PIV)techniques.There are three near-wall topological patterns with different Angles of Attack(AoAs):the separation bubble,the Leading-Edge Vortex(LEV)and the high Ao As flow.For the separation bubble pattern,two saddles and two foci form in the middle of the model.The features of the LEV pattern are the leading-edge separation lines.The topological characteristics of the separation lines are changed by the interaction between the LEV and the Wing-Tip Vortex(WTV).For the high Ao As flow pattern,four unstable foci are found at the forewing and the hindwing respectively.The angle between the trajectory of the WTV and the model increases with increasing Ao A even though the slope of the WTV angle versus Ao A curve declines at the moderate AoAs.
基金National Natural Science Foundation of China(No.40975093)the Innovation Foundation of Shanghai Education Commission,China(No.14ZZ073)the Chinese Universities Scientific Fund,China(No.CUSF-DH-D-2013051)
文摘The impact of thermal conditions of the ground on ventilation in the interior courtyard and rooms of enclosed building is very important to improve the air quality in courtyard. The computational fluid dynamics( CFD) model was used to investigate the flow field of a certain courtyard and analyze the static differential pressure between the two sides of the vent and ventilation conditions of the courtyard. The results indicate that thermal effects not only changed the air flow pattern of the interior courtyard but also obviously increased the flow velocity of the upper space of the courtyard. For the most of courtyard rooms,the absolute value of static differential pressure increases as the thermal intensity of the ground increases. In all wind directions,the air exchange rate of the courtyard increases with the higher thermal intensity of the ground which makes a greater influence on the increasing of the ventilation rate of the roof opening than that on the gate opening.
基金supported by the Basic Science Center Program for Ordered Energy Conversion of the National Natural Science Foundation of China(No.52488201)the National Natural Science Foundation of China(No.52422606).
文摘Hilly terrain pipeline is a common form of pipeline in oil and gas storage and transportation industry.Due to the hilly terrain influence, the liquid at the elbow of the gathering pipeline is easy to flow back and accumulate to form slug flow, so it is necessary to remove the accumulated liquid by gas purging. In this paper, experiment is carried out in hilly terrain pipelines. Three flow patterns of stratified flow, slug flow and stratified entrained flow are observed. The process of gas purging accumulated liquid is divided into four stages, namely liquid accumulation, liquid rising, continuous outflow and tail outflow. At the same time, the flow pattern maps of each stage are drawn. The pressure drop signal is analyzed in time domain and frequency domain, and the contour map of pressure drop distribution is drawn. It is found that the ratio of range to average value can well distinguish the occurrence range of each flow pattern.Based on visualization, the transition process of slug flow to stratified flow and stratified entrained flow is studied, and the transition boundary prediction model is established. An image processing method is proposed to convert the image signal into a similarity curve, and PSD analysis is performed to calculate the slug frequency. The normal distribution is used to fit the slug frequency, and the predicted correlation is in good agreement with the experimental data.
基金supported by the National Natural Science Foundation of China(Grant Nos.12172017 and 11872083)Project of Beijing Municipal Education Commission(Grant Nos.KZ202210005006 and KZ202110005007).
文摘Intracranial aneurysm(IA)is a prevalent cerebrovascular disease associated with high mortality and disability rates upon rupture.The hemodynamics of IA,which are significantly influenced by geometric parameters,directly impact its rupture.This study focuses on investigating the transient flow characteristics in saccular IA models fabricated using a water droplet-based method,specifically examining the influence of neck widths.Particle image velocimetry technique and numerical simulation were employed to investigate the dynamic evolution of flow structures within three IA models.The results reveal that neck width(W)has a substantial effect on flow characteristics in the neck region,subsequently impacting the deep flow inside the sac.Three distinct patterns were observed during flow evolution inside the sac:for W=2 mm,two vortices occur and then disappear with relatively low average flow velocity;for W=4 mm,enhanced effects of a high-speed jet result in periodic pulsatile flow velocity distribution while maintaining stable vortex core position;for W=6 mm,significant changes in flow velocity occur due to size expansion and intensity increase of vortices.These findings demonstrate that neck widths play a complex role in influencing transient flow characteristics within IAs.Overall,this research contributes to further understanding transient flow behaviors in IAs.
基金the National Key R&D Program of China(Nos.2021YFC2902400 and 2021YFC2902401)the project of State Key Laboratory of Intelligent Optimized Manufacturing in Mining&Metallurgy Process(No.BGRIMM-KZSKL-2023-14).
文摘The hydrogen-enriched direct reduction shaft furnace addresses the high CO_(2) emissions associated with the blast furnace process.A discrete element method(DEM)model was introduced to explore how the structure of the diversion cone affects particle descent behavior in a hydrogen-enriched shaft furnace.The results indicated that in the absence of a diversion cone,the descending velocity near the furnace wall zone is significantly lower than that at its center,resulting in a‘V’-shaped burden flow pattern.The discharge velocity has a minor impact on the flow pattern in the shaft furnace.Upon installation of a diversion cone,burden descending velocity becomes more uniform,leading to a‘-’-shaped burden flow pattern.As the bottom of the diversion cone ascends(i.e.,the lower end of the diversion cone is progressively closer to the top),there is an increase in the volume fraction of the dead zone within the shaft furnace.This is particularly evident in the formation of a triangular dead zone at the base of the diversion cone.It is suggested that the lower cone of the bi-conical diversion cone should maintain a sufficient height.
基金supported by the National Natural Science Foundation of China(Project No.52166004)the National Key Research and Development Program of China(Project No.2022YFC3902000)the Major Science and Technology Special Project of Yunnan Province(Project Nos.202202AG050007,202202AG050002).
文摘This research explores the characteristics of boiling in inclined pipes,a domain of great importance in engineering.Employing an experimental visualization technique,the boiling dynamics of deionizedwater are examined at varying inclination angles,paying special attention to the emerging flow patterns.The findings demonstrate that the inclination angle significantly impacts flow pattern transitions within the 0°to 90°range.As the heat flux rises,bubbles form in the liquid.The liquid’s inertia extends the bubble-wall contact time,thereby delaying the onset of bulk bubble flow.Beyond a 90°inclination,however,the patterning behavior is more influenced by the fluid velocity.At low speeds,incomplete pipe filling results in a large liquid plug hindering flow,while high speeds lead to full pipe filling.In general,gravity,inertia,buoyancy forces,and capillary forces are themain influential factors in the considered problem.However,an analysis of the heat transfer coefficient and boiling curve for different inclination angles reveals that the observed variations are essentially due to corresponding changes in the flow pattern.Finally,an optimal mass flux and inclination angle,able to minimize total entropy generation and improve heat transfer efficiency,are determined by means of an entropy generation analysis.
