The aim of the paper is to discover the general creep mechanisms for the short fiber reinforcement matrix composites (MMCs) under uniaxial stress states and to build a relationship between the macroscopic steady creep...The aim of the paper is to discover the general creep mechanisms for the short fiber reinforcement matrix composites (MMCs) under uniaxial stress states and to build a relationship between the macroscopic steady creep behavior and the material micro geometric parameters. The unit cell models were used to calculate the macroscopic creep behavior with different micro geometric parameters of fibers on different loading directions. The influence of the geometric parameters of the fibers and loading directions on the macroscopic creep behavior had been obtained, and described quantitatively. The matrix/fiber interface had been considered by a third layer, matrix/fiber interlayer, in the unit cells with different creep properties and thickness. Based on the numerical results of the unit cell models, a statistic model had been presented for the plane randomly-distributed-fiber MMCs. The fiber breakage had been taken into account in the statistic model for it starts experimentally early in the creep life. With the distribution of the geometric parameters of the fibers, the results of the statistic model agree well with the experiments. With the statistic model, the influence of the geometric parameters and the breakage of the fibers as well as the properties and thickness of, the interlayer on the macroscopic steady creep rate have been discussed.展开更多
A two-dimensional axisymmetric finite element model based on an improved cohesive element method was developed to simulate interfacial debonding, sliding friction, and residual thermal stresses in SiC composites durin...A two-dimensional axisymmetric finite element model based on an improved cohesive element method was developed to simulate interfacial debonding, sliding friction, and residual thermal stresses in SiC composites during single-fiber push-out tests to extract the interfacial bond strength and frictional stress. The numerical load–displacement curves agree well with experimental curves,indicating that this cohesive element method can be used for calculating the interfacial properties of SiC composites.The simulation results show that cracks are most likely to occur at the ends of the experimental sample, where the maximum shear stress is observed and that the interfacial shear strength and constant sliding friction stress decrease with an increase in temperature. Moreover, the load required to cause complete interfacial failure increases with the increase in critical shear strength, and the composite materials with higher fiber volume fractions have higher bearing capacities. In addition, the initial failure load increases with an increase in interphase thickness.展开更多
文摘The aim of the paper is to discover the general creep mechanisms for the short fiber reinforcement matrix composites (MMCs) under uniaxial stress states and to build a relationship between the macroscopic steady creep behavior and the material micro geometric parameters. The unit cell models were used to calculate the macroscopic creep behavior with different micro geometric parameters of fibers on different loading directions. The influence of the geometric parameters of the fibers and loading directions on the macroscopic creep behavior had been obtained, and described quantitatively. The matrix/fiber interface had been considered by a third layer, matrix/fiber interlayer, in the unit cells with different creep properties and thickness. Based on the numerical results of the unit cell models, a statistic model had been presented for the plane randomly-distributed-fiber MMCs. The fiber breakage had been taken into account in the statistic model for it starts experimentally early in the creep life. With the distribution of the geometric parameters of the fibers, the results of the statistic model agree well with the experiments. With the statistic model, the influence of the geometric parameters and the breakage of the fibers as well as the properties and thickness of, the interlayer on the macroscopic steady creep rate have been discussed.
基金supported by the National Natural Science Foundation of China(No.11405124)Science Challenge Project(No.TZ2018004)+1 种基金Natural Science Basic Research Plan in Shaanxi Province of China(No.2015JQ1030)the Shaanxi Province Postdoctoral Science Foundation(2014)
文摘A two-dimensional axisymmetric finite element model based on an improved cohesive element method was developed to simulate interfacial debonding, sliding friction, and residual thermal stresses in SiC composites during single-fiber push-out tests to extract the interfacial bond strength and frictional stress. The numerical load–displacement curves agree well with experimental curves,indicating that this cohesive element method can be used for calculating the interfacial properties of SiC composites.The simulation results show that cracks are most likely to occur at the ends of the experimental sample, where the maximum shear stress is observed and that the interfacial shear strength and constant sliding friction stress decrease with an increase in temperature. Moreover, the load required to cause complete interfacial failure increases with the increase in critical shear strength, and the composite materials with higher fiber volume fractions have higher bearing capacities. In addition, the initial failure load increases with an increase in interphase thickness.
