The characteristics of a kind of comb-drive electrostatic actuated micro-gripper are tested. The test platform using a microscope-CCD-computer, the state information of the micro-gripper obtained by data acquisition a...The characteristics of a kind of comb-drive electrostatic actuated micro-gripper are tested. The test platform using a microscope-CCD-computer, the state information of the micro-gripper obtained by data acquisition and image processing, voltage-displacement characteristic curve is obtained and the mathematical equation is established. The analysis of the characteristic equation has shown the consistency and rationality of the theoretical design and the experimental results. The main factors that cause the difference between the theoretical design and the actual test performance are analyzed, and the design method and experimental results is obtained for the micro-gripper in the field of micro-assembly.展开更多
[Objective]The aim was to study the simulation test of hydrodynamics process of erosion.[Method]Through the runoff scouring experiment,the property of soil erosion in Damaoqi grassland in Inner Mongolia was studied.Th...[Objective]The aim was to study the simulation test of hydrodynamics process of erosion.[Method]Through the runoff scouring experiment,the property of soil erosion in Damaoqi grassland in Inner Mongolia was studied.The process and mechanism of soil erosion were studied.[Result]The results of runoff scouring experiment on inner Damaoqi steppe showed that the mean flow velocity of change slope increased with the discharge of flow and slope gradient.The mean silt content rate,the mean sediment transport rate and the mean sheer stress all increased when the discharge of flow increased,which changed in parabolic form with the increase of slope gradient and the critical gradient is 25°.The relationship between the mean sediment transport rate and the mean sheer stress was linear.[Conclusion]The study provided theoretic basis for the report of soil erosion in grassland in China.展开更多
Experimental Design and Data Processing is an important core professional basic course for food science majors.This course is theoretical and practical,and there are many formulas,abstract contents and difficult to un...Experimental Design and Data Processing is an important core professional basic course for food science majors.This course is theoretical and practical,and there are many formulas,abstract contents and difficult to understand,and there are some problems in the teaching process,such as students1 poor interest in learning,insufficient mastery of what they have learned,and inability to combine theory with practice organically.Through analyzing the existing problems,this paper puts forward some reform measures for the teaching mode of experimental design and data processing by using the intelligent teaching of Superstar platform.展开更多
With the aid of the latest fiber optic sensing technology parameters in the cure process of ther- mosetting resin-matrix composite, such as temperature, viscosity,void and residual stress, can be monitored entirely an...With the aid of the latest fiber optic sensing technology parameters in the cure process of ther- mosetting resin-matrix composite, such as temperature, viscosity,void and residual stress, can be monitored entirely and efficiently.In this paper, experiment results of viscosity measurement in composite cure process in autoclave using fiber optic sensors are presented. Based on the sensed information, a computer program is utilized to control the cure process. With this technology, the cure process becomes more apparent and controllable, which will greatly improve the cured products and reduce the cost.展开更多
The current study was to understand how process variables of high shear wet granulations affect physical properties of granules and tablets. The knowledge gained was intended to be used for Quality-by-Design based pro...The current study was to understand how process variables of high shear wet granulations affect physical properties of granules and tablets. The knowledge gained was intended to be used for Quality-by-Design based process design and optimization. The variables were selected based on the risk assessment as impeller speed, liquid addition rate, and wet massing time. Formulation compositions were kept constant to minimize their influence on granules properties. Multiple linear regression models were built providing understanding of the impact of each variable on granule hardness, Carr’s index, tablet tensile strength, surface mean diameter of granules, and compression behavior. The experimental results showed that the impact of impeller speed was more dominant compared to wet massing time and water addition rate. The results also revealed that quality of granules and tablets could be optimized by adjusting specific process variables(impeller speed 1193 rpm, water spray rate 3.7 ml/min, and wet massing time 2.84 min). Overall desirability was 0.84 suggesting that the response values were closer to the target one. The SEM image of granules showed that spherical and smooth granules produced at higher impeller speed, whereas rough and irregular shape granules at lower speed. Moreover, multivariate data analysis demonstrated that impeller speed and massing time had strong correlation with the granule and tablet properties. In overall, the combined experimental design and principal component analysis approach allowed to better understand the correlation between process variables and granules and tablet attributes.展开更多
Analytic Hierarchy Process is selected according to the selection method of leading industries by both domestic and foreign scholars. Leading industries which can accelerate the overall economic development of Anshun ...Analytic Hierarchy Process is selected according to the selection method of leading industries by both domestic and foreign scholars. Leading industries which can accelerate the overall economic development of Anshun Experimental District is taken as the target layer; and market demand, efficiency standards and local conditions are taken as the criterion layers, so as to construct the select model of leading industry and to choose the leading industry in Anshun Experimental District. Result shows that the priority order of the leading industry selection in Anshun Experimental District is as follows: tourism > pharmacy > transportation > energy > food processing > characteristic agriculture > package and printing > automobile industry > mining > electric engineering.展开更多
A new meso-mechanical testing scheme based on SEM was developed to carry out the experiment of microfracturing process of rocks. The microfracturing process of the pre-crack marble sample on surrounding rock in the im...A new meso-mechanical testing scheme based on SEM was developed to carry out the experiment of microfracturing process of rocks. The microfracturing process of the pre-crack marble sample on surrounding rock in the immerged Long-big tunnel in Jinping Cascade II Hydropower Station under uniaxial compression was recorded by using the testing scheme. According to the stereology theory, the propagation and coalescent of cracks at meso-scale were quantitatively investigated with digital technology. Therefore, the basic geometric information of rock microcracks such as area, angle, length, width, perimeter, was obtained from binary images after segmentation. The failure mechanism of specimen under uniaxial compression with the quantitative information was studied from macro and microscopic point of view. The results show that the image of microfracturing process of the specimen can be observed and recorded digitally. During the damage of the specimen, the distribution of microcracks in the specimen is still subjected to exponential distribution with some microcracks concentrated in certain regions. Finally, the change law of the fractal dimension of the local element in marble sample under different external load conditions is obtained by means of the statistical calculation of the fractal dimension.展开更多
This article investigates the low-temperature formation of aluminide coatings on a Ni-base superalloy by pack cementation process. The pack cemented coatings characteristic of high density and homogeneity possess a tw...This article investigates the low-temperature formation of aluminide coatings on a Ni-base superalloy by pack cementation process. The pack cemented coatings characteristic of high density and homogeneity possess a two-layer structure. The top layer mainly consists of Al3Ni2 and Al3Ni,while the bottom layer of Al3Ni2. Great efforts are made to elucidate the effects of different experimental parameters on the microstructure and the constituent distribution of the coatings. The results show that all the parameters exclusive of the pack activator （NH4Cl） content produce effect on the coating thickness,but do not on the microstructure and the constituent distribution. The pack activator （NH4Cl） content affects neither the coating thickness nor structure and constituent distribution. The parabolic relationship between the coating thickness and the deposition time suggests that the process is diffusion-controlled. Furthermore,the article demonstrates a linear relationship between the coating thickness and the re-ciprocal deposition temperature.展开更多
The application of computer in the quantitative analysis chemistry experiment is a chemistry experiment teaching applications software, developed by Visual Basic （6.0）, based on the content of quantitative analysis ...The application of computer in the quantitative analysis chemistry experiment is a chemistry experiment teaching applications software, developed by Visual Basic （6.0）, based on the content of quantitative analysis chemistry experiment of chemistry major in higher institute. This software has the function of the automatic processing the experimental data, the automatic generation of test report copies, and the automatic evaluation of students＇ experimental results, which solve the reliability, objectivity and accuracy problems of the students＇ experiment data processing and evaluation, and avoid interference with human factors. The software has the characteristic of the easy installation, the easy operation, the strong practicability, pertinence, the systematicness and the running stability, so it provides a platform in the quantitative analysis chemistry experiment for the students＇ assessment system of automatic processing, and it has a high popularization value. The project＇s technical route design is reasonable, the research method is correct, and the experimental data processing results are reliable, which has reached the leading domestic level in the quantitative analysis chemistry experiment teaching field of computer data processing. And this project has been through the achievements appraisal of Gansu Provincial Sci. ＆ Tech. Department.展开更多
To the Editor:Nowadays,because of the infiltration of cholangiocarcinoma to the parenchyma and/or bile ducts of the caudate lobe,the inclusion of caudate lobe combined with a major hepatectomy remains the gold standar...To the Editor:Nowadays,because of the infiltration of cholangiocarcinoma to the parenchyma and/or bile ducts of the caudate lobe,the inclusion of caudate lobe combined with a major hepatectomy remains the gold standard approach for a resectable hilar cholangiocarcinoma.Since the last years of the 20th century,some authors have begun to report isolated caudate lobe resection for hepatocellular.展开更多
The mechanisms of heat transfer through the sinter beds of the MEBIOS process are discussed and their comprehensive mathematical model is proposed. The MEBIOS process, the concept of which has been proposed ear- lier ...The mechanisms of heat transfer through the sinter beds of the MEBIOS process are discussed and their comprehensive mathematical model is proposed. The MEBIOS process, the concept of which has been proposed ear- lier by the authors, allows using both coarse and fine particles of iron ores in the same sinter bed. The study includes two parts. The first part describes the model content and the results of its experimental verification. The model ac- counts for coal combustion, limestone decomposition, moisture evaporation/condensation, and melting/solidifying of solid phases. The model predictions are in good agreement with the experimental data. Typical numerical results of the sintering process and the key parameters influencing the process efficiency are discussed in the second part of the study.展开更多
Laser surface transformation hardening becomes one of the most modern processes used to improve fatigue and wear properties of steel surfaces. In this process, the material properties and the heating parameters are th...Laser surface transformation hardening becomes one of the most modern processes used to improve fatigue and wear properties of steel surfaces. In this process, the material properties and the heating parameters are the factors that present the most significant effects on the hardened surface attributes. The control of these factors using predictive modeling approaches to achieve desired surface properties leads to conclusive results. However, when the dimensions of the surface to be treated are larger than the cross-section of the laser beam, various laser-scanning patterns are involved. This paper presents an experimental investigation of laser surface hardening of AISI 4340 steel using different laser scanning patterns. This investigation is based on a structured experimental design using the Taguchi method and improved statistical analysis tools. Experiments are carried out using a 3 kW Nd: YAG laser source in order to evaluate the effects of the heating parameters and patterns design parameters on the physical and geometrical characteristics of the hardened surface. Laser power, scanning speed and scanning patterns (linear, sinusoidal, triangular and trochoid) are the factors used to evaluate the hardened depth and the hardened width variations and to identify the possible relationship between these factors and the hardened zone attributes. Various statistical tools such as ANOVA, correlations analysis and response surfaces are applied in order to examine the effects of the experimental factors on the hardened surface characteristics. The results reveal that the scanning patterns do not modify the nature of the laser parameters’ effects on the hardened depth and the hardened width. But they can accentuate or reduce these effects depending on the type of the considered pattern. The results show also that the sinusoidal and the triangular patterns are relevant when a maximum hardened width with an acceptable hardened depth is desired.展开更多
[Objectives] This study was conducted to detect the two-dimensional diffusion concentration distribution from sloped wave bank. [Methods] Diffusion experiments of instantaneous line source discharge were carried out u...[Objectives] This study was conducted to detect the two-dimensional diffusion concentration distribution from sloped wave bank. [Methods] Diffusion experiments of instantaneous line source discharge were carried out using two sloped wave banks with different inclination angles based on the developed two-dimensional diffusion tank device for sloped wave banks by the apex discharge method under grid oscillation frequencies n=15, 20, 40 and 60 r/min. The image acquisition and digital image processing techniques were applied to measure the two-dimensional concentration field distribution and to analyze the distribution laws of the pollutant in the angular field. [Results] The diffusion of the pollutant in the sloped wave bank area became faster with the increase of the grid oscillation frequency, and the pollution range became wider with the diffusion time. The point concentration of the pollutant at the water surface monotonically decreased with the increase of the abscissa, and the vertical concentration distribution decreased with the increase of water depth. The transverse diffusion rate of the pollutant in water was greater than the vertical diffusion rate, and its concentration distribution exhibited a distribution characteristic of farther diffusion in the adjacent area on the water surface. The diffusion experiment area of the sloped wave bank at θ=30° had a higher concentration of the pollutant at each point compared with the diffusion experiment of the sloped bank at θ=45°, under the same experimental conditions. A large-scale vortex appeared near the sloped wave bank at θ=45° during the experiment, and the presence of the vortex made the concentration distribution of the pollutant in the direction along the bank slope first decrease and then increase, while no obvious vortex was observed near the sloped wave bank at θ=30°, and the concentration of the pollutant decreased monotonously along the bank slope direction. [Conclusions] This study is of great significance for the concentration distribution laws and the lateral and vertical diffusion coefficients of side discharge at complex bank slopes and river banks.展开更多
文摘The characteristics of a kind of comb-drive electrostatic actuated micro-gripper are tested. The test platform using a microscope-CCD-computer, the state information of the micro-gripper obtained by data acquisition and image processing, voltage-displacement characteristic curve is obtained and the mathematical equation is established. The analysis of the characteristic equation has shown the consistency and rationality of the theoretical design and the experimental results. The main factors that cause the difference between the theoretical design and the actual test performance are analyzed, and the design method and experimental results is obtained for the micro-gripper in the field of micro-assembly.
基金Supported by the Scientific Research Program of China Institute of Water Resources and Hydropower Research (MKS2010001)
文摘[Objective]The aim was to study the simulation test of hydrodynamics process of erosion.[Method]Through the runoff scouring experiment,the property of soil erosion in Damaoqi grassland in Inner Mongolia was studied.The process and mechanism of soil erosion were studied.[Result]The results of runoff scouring experiment on inner Damaoqi steppe showed that the mean flow velocity of change slope increased with the discharge of flow and slope gradient.The mean silt content rate,the mean sediment transport rate and the mean sheer stress all increased when the discharge of flow increased,which changed in parabolic form with the increase of slope gradient and the critical gradient is 25°.The relationship between the mean sediment transport rate and the mean sheer stress was linear.[Conclusion]The study provided theoretic basis for the report of soil erosion in grassland in China.
基金The foundation for Teaching Research Project of Hubei University of Technology in Hubei Province in 2020(grant number 2020017).
文摘Experimental Design and Data Processing is an important core professional basic course for food science majors.This course is theoretical and practical,and there are many formulas,abstract contents and difficult to understand,and there are some problems in the teaching process,such as students1 poor interest in learning,insufficient mastery of what they have learned,and inability to combine theory with practice organically.Through analyzing the existing problems,this paper puts forward some reform measures for the teaching mode of experimental design and data processing by using the intelligent teaching of Superstar platform.
文摘With the aid of the latest fiber optic sensing technology parameters in the cure process of ther- mosetting resin-matrix composite, such as temperature, viscosity,void and residual stress, can be monitored entirely and efficiently.In this paper, experiment results of viscosity measurement in composite cure process in autoclave using fiber optic sensors are presented. Based on the sensed information, a computer program is utilized to control the cure process. With this technology, the cure process becomes more apparent and controllable, which will greatly improve the cured products and reduce the cost.
基金supported by the National Research Foun-dation of Korea(NRF)grant,funded by the Korean govern-ment(MSIT)(2015R1A1A1A05000942)the National Re-search Foundation of Korea(NRF)grant funded by the Korea government(MSIT)(NRF-2018R1A5A2023127)
文摘The current study was to understand how process variables of high shear wet granulations affect physical properties of granules and tablets. The knowledge gained was intended to be used for Quality-by-Design based process design and optimization. The variables were selected based on the risk assessment as impeller speed, liquid addition rate, and wet massing time. Formulation compositions were kept constant to minimize their influence on granules properties. Multiple linear regression models were built providing understanding of the impact of each variable on granule hardness, Carr’s index, tablet tensile strength, surface mean diameter of granules, and compression behavior. The experimental results showed that the impact of impeller speed was more dominant compared to wet massing time and water addition rate. The results also revealed that quality of granules and tablets could be optimized by adjusting specific process variables(impeller speed 1193 rpm, water spray rate 3.7 ml/min, and wet massing time 2.84 min). Overall desirability was 0.84 suggesting that the response values were closer to the target one. The SEM image of granules showed that spherical and smooth granules produced at higher impeller speed, whereas rough and irregular shape granules at lower speed. Moreover, multivariate data analysis demonstrated that impeller speed and massing time had strong correlation with the granule and tablet properties. In overall, the combined experimental design and principal component analysis approach allowed to better understand the correlation between process variables and granules and tablet attributes.
基金Supported by the Humanities and Social Sciences Planning Project of Guizhou Province (2008GH043)
文摘Analytic Hierarchy Process is selected according to the selection method of leading industries by both domestic and foreign scholars. Leading industries which can accelerate the overall economic development of Anshun Experimental District is taken as the target layer; and market demand, efficiency standards and local conditions are taken as the criterion layers, so as to construct the select model of leading industry and to choose the leading industry in Anshun Experimental District. Result shows that the priority order of the leading industry selection in Anshun Experimental District is as follows: tourism > pharmacy > transportation > energy > food processing > characteristic agriculture > package and printing > automobile industry > mining > electric engineering.
基金Projects(50674040, 50539090) supported by the National Natural Science Foundation of ChinaProject(CX07B_128z) supported by the Cultivate Creative Postgraduate Foundation of Jiangsu Province, China
文摘A new meso-mechanical testing scheme based on SEM was developed to carry out the experiment of microfracturing process of rocks. The microfracturing process of the pre-crack marble sample on surrounding rock in the immerged Long-big tunnel in Jinping Cascade II Hydropower Station under uniaxial compression was recorded by using the testing scheme. According to the stereology theory, the propagation and coalescent of cracks at meso-scale were quantitatively investigated with digital technology. Therefore, the basic geometric information of rock microcracks such as area, angle, length, width, perimeter, was obtained from binary images after segmentation. The failure mechanism of specimen under uniaxial compression with the quantitative information was studied from macro and microscopic point of view. The results show that the image of microfracturing process of the specimen can be observed and recorded digitally. During the damage of the specimen, the distribution of microcracks in the specimen is still subjected to exponential distribution with some microcracks concentrated in certain regions. Finally, the change law of the fractal dimension of the local element in marble sample under different external load conditions is obtained by means of the statistical calculation of the fractal dimension.
文摘This article investigates the low-temperature formation of aluminide coatings on a Ni-base superalloy by pack cementation process. The pack cemented coatings characteristic of high density and homogeneity possess a two-layer structure. The top layer mainly consists of Al3Ni2 and Al3Ni,while the bottom layer of Al3Ni2. Great efforts are made to elucidate the effects of different experimental parameters on the microstructure and the constituent distribution of the coatings. The results show that all the parameters exclusive of the pack activator （NH4Cl） content produce effect on the coating thickness,but do not on the microstructure and the constituent distribution. The pack activator （NH4Cl） content affects neither the coating thickness nor structure and constituent distribution. The parabolic relationship between the coating thickness and the deposition time suggests that the process is diffusion-controlled. Furthermore,the article demonstrates a linear relationship between the coating thickness and the re-ciprocal deposition temperature.
文摘The application of computer in the quantitative analysis chemistry experiment is a chemistry experiment teaching applications software, developed by Visual Basic （6.0）, based on the content of quantitative analysis chemistry experiment of chemistry major in higher institute. This software has the function of the automatic processing the experimental data, the automatic generation of test report copies, and the automatic evaluation of students＇ experimental results, which solve the reliability, objectivity and accuracy problems of the students＇ experiment data processing and evaluation, and avoid interference with human factors. The software has the characteristic of the easy installation, the easy operation, the strong practicability, pertinence, the systematicness and the running stability, so it provides a platform in the quantitative analysis chemistry experiment for the students＇ assessment system of automatic processing, and it has a high popularization value. The project＇s technical route design is reasonable, the research method is correct, and the experimental data processing results are reliable, which has reached the leading domestic level in the quantitative analysis chemistry experiment teaching field of computer data processing. And this project has been through the achievements appraisal of Gansu Provincial Sci. ＆ Tech. Department.
文摘To the Editor:Nowadays,because of the infiltration of cholangiocarcinoma to the parenchyma and/or bile ducts of the caudate lobe,the inclusion of caudate lobe combined with a major hepatectomy remains the gold standard approach for a resectable hilar cholangiocarcinoma.Since the last years of the 20th century,some authors have begun to report isolated caudate lobe resection for hepatocellular.
文摘The mechanisms of heat transfer through the sinter beds of the MEBIOS process are discussed and their comprehensive mathematical model is proposed. The MEBIOS process, the concept of which has been proposed ear- lier by the authors, allows using both coarse and fine particles of iron ores in the same sinter bed. The study includes two parts. The first part describes the model content and the results of its experimental verification. The model ac- counts for coal combustion, limestone decomposition, moisture evaporation/condensation, and melting/solidifying of solid phases. The model predictions are in good agreement with the experimental data. Typical numerical results of the sintering process and the key parameters influencing the process efficiency are discussed in the second part of the study.
文摘Laser surface transformation hardening becomes one of the most modern processes used to improve fatigue and wear properties of steel surfaces. In this process, the material properties and the heating parameters are the factors that present the most significant effects on the hardened surface attributes. The control of these factors using predictive modeling approaches to achieve desired surface properties leads to conclusive results. However, when the dimensions of the surface to be treated are larger than the cross-section of the laser beam, various laser-scanning patterns are involved. This paper presents an experimental investigation of laser surface hardening of AISI 4340 steel using different laser scanning patterns. This investigation is based on a structured experimental design using the Taguchi method and improved statistical analysis tools. Experiments are carried out using a 3 kW Nd: YAG laser source in order to evaluate the effects of the heating parameters and patterns design parameters on the physical and geometrical characteristics of the hardened surface. Laser power, scanning speed and scanning patterns (linear, sinusoidal, triangular and trochoid) are the factors used to evaluate the hardened depth and the hardened width variations and to identify the possible relationship between these factors and the hardened zone attributes. Various statistical tools such as ANOVA, correlations analysis and response surfaces are applied in order to examine the effects of the experimental factors on the hardened surface characteristics. The results reveal that the scanning patterns do not modify the nature of the laser parameters’ effects on the hardened depth and the hardened width. But they can accentuate or reduce these effects depending on the type of the considered pattern. The results show also that the sinusoidal and the triangular patterns are relevant when a maximum hardened width with an acceptable hardened depth is desired.
基金Supported by Major Agricultural Application Technology Innovation Project of Shandong Province(SD2019ZZ020)
文摘[Objectives] This study was conducted to detect the two-dimensional diffusion concentration distribution from sloped wave bank. [Methods] Diffusion experiments of instantaneous line source discharge were carried out using two sloped wave banks with different inclination angles based on the developed two-dimensional diffusion tank device for sloped wave banks by the apex discharge method under grid oscillation frequencies n=15, 20, 40 and 60 r/min. The image acquisition and digital image processing techniques were applied to measure the two-dimensional concentration field distribution and to analyze the distribution laws of the pollutant in the angular field. [Results] The diffusion of the pollutant in the sloped wave bank area became faster with the increase of the grid oscillation frequency, and the pollution range became wider with the diffusion time. The point concentration of the pollutant at the water surface monotonically decreased with the increase of the abscissa, and the vertical concentration distribution decreased with the increase of water depth. The transverse diffusion rate of the pollutant in water was greater than the vertical diffusion rate, and its concentration distribution exhibited a distribution characteristic of farther diffusion in the adjacent area on the water surface. The diffusion experiment area of the sloped wave bank at θ=30° had a higher concentration of the pollutant at each point compared with the diffusion experiment of the sloped bank at θ=45°, under the same experimental conditions. A large-scale vortex appeared near the sloped wave bank at θ=45° during the experiment, and the presence of the vortex made the concentration distribution of the pollutant in the direction along the bank slope first decrease and then increase, while no obvious vortex was observed near the sloped wave bank at θ=30°, and the concentration of the pollutant decreased monotonously along the bank slope direction. [Conclusions] This study is of great significance for the concentration distribution laws and the lateral and vertical diffusion coefficients of side discharge at complex bank slopes and river banks.
