A simple general relation P = Q + R + 1 between the number P of kinds of species, the number Q of charge and elemental/core balances and the number R of independent equilibrium constants is deduced, and its validity i...A simple general relation P = Q + R + 1 between the number P of kinds of species, the number Q of charge and elemental/core balances and the number R of independent equilibrium constants is deduced, and its validity is confirmed for non-redox and redox electrolytic systems, of different degree of complexity.展开更多
In this paper, it is proved that linear combination 2·f(O)?- f(H) of elemental balances: f(O) for O and f(H) for H is linearly independent on charge and elemental/core balances for all redox systems of any degree...In this paper, it is proved that linear combination 2·f(O)?- f(H) of elemental balances: f(O) for O and f(H) for H is linearly independent on charge and elemental/core balances for all redox systems of any degree of complexity;it is the primary form of the Generalized Electron Balance (GEB), , considered as the Approach II to GEB. The Approach II is equivalent to the Approach I based on the principle of common pool of electrons. Both Approaches are illustrated on an example of titration of acidified (H2SO4) solution of H2C2O4 with KMnO4. It is also stated, on an example of titration of the same solution with NaOH, that 2·f(O)?- f(H) is a linear combination of charge and elemental/core balances, i.e. it is not an independent balance when related to the non-redox system. These properties of 2·f(O)?- f(H) can be extended on redox and non-redox systems, of any degree of complexity, i.e. the linear independency/dependency of 2·f(O)?- f(H) on other balances related to a system in question is a criterion distinguishing redox and non-redox systems. The GEB completes the set of (charge and concentration) balances and a set of expressions for independent equilibrium constants needed for modeling the related redox system.展开更多
Low-cost and high-safety aqueous Zn-I_(2) batteries attract extensive attention for large-scale energy storage systems.However,polyiodide shuttling and sluggish iodine conversion reactions lead to inferior rate capabi...Low-cost and high-safety aqueous Zn-I_(2) batteries attract extensive attention for large-scale energy storage systems.However,polyiodide shuttling and sluggish iodine conversion reactions lead to inferior rate capability and severe capacity decay.Herein,a three-dimensional polyaniline is wrapped by carboxylcarbon nanotubes(denoted as C-PANI)which is designed as a catalytic cathode to effectively boost iodine conversion with suppressed polyiodide shuttling,thereby improving Zn-I_(2) batteries.Specifically,carboxyl-carbon nanotubes serve as a proton reservoir for more protonated-NH+=sites in PANI chains,achieving a direct I0/I−reaction for suppressed polyiodide generation and Zn corrosion.Attributing to this“proton-iodine”regulation,catalytic protonated C-PANI strongly fixes electrolytic iodine species and stores proton ions simultaneously through reversible-N=/-NH^(+)-reaction.Therefore,the electrolytic Zn-I_(2) battery with C-PANI cathode exhibits an impressive capacity of 420 mAh g^(−1) and ultra-long lifespan over 40,000 cycles.Additionally,a 60 mAh pouch cell was assembled with excellent cycling stability after 100 cycles,providing new insights into exploring effective organocatalysts for superb Zn-halogen batteries.展开更多
A number of studies have been reported on the use of nanocrystalline plasma electrolytic nitrocarburising technology for surface hardening of stainless steels for higher corrosion resistance resulted from this techniq...A number of studies have been reported on the use of nanocrystalline plasma electrolytic nitrocarburising technology for surface hardening of stainless steels for higher corrosion resistance resulted from this technique. However, very few studies have focused on the optimization of the nanocrystalline plasma electrolytic nitrocarburising process parameters. In this study, a design of experiment （DOE） technique, the Taguchi method, has been used to optimize the nanocrystalline plasma electrolytic nitrocarburising not only for surface hardening but also for the corrosion protection of 316L austenitic stainless steel by controlling the coating processes factors. The experimental design consisted of four factors （Urea concentration, electrical conductivity of electrolyte, voltage and duration of process）, each containing three levels. Potentiodynamic polarization measurements were carried out to determine the corrosion resistance of the coated samples. The results were analyzed with related software. An analysis of the mean of signal-to-noise （S/N） ratio indicated that the corrosion resistance of nanocrystalline plasma electrolytic nitrocarburised 316L stainless steel was influenced significantly by the levels in the Taguchi orthogonal array. The optimized coating parameters for corrosion resistance are 1150 g/L for urea concentration, 360 mS/cm for electrical conductivity of electrolyte, 260 V for applied voltage, 6 min for treatment time. The percentage of contribution for each factor was determined by the analysis of variance （ANOVA）. The results showed that the applied voltage is the most significant factor affecting the corrosion resistance of the coatings.展开更多
This study for the first time proposed an efficient microbial electrolyte/UV system for Methyl Orange decomposition. With an external applied voltage of 0.2 V and cathode aeration of20 mL/min, H2O2 could be in-situ ge...This study for the first time proposed an efficient microbial electrolyte/UV system for Methyl Orange decomposition. With an external applied voltage of 0.2 V and cathode aeration of20 mL/min, H2O2 could be in-situ generated from two-electron reduction of oxygen in cathode, reaching to 8.1 mg/L in 2 hr and continued to increase. The pollutant removal efficiency of approximate 94.7% was achieved at initial neutral pH, with the activation of ·OH in the presence of UV illumination. Although the nature of its guiding principles remain on the vista of practical exploration, this proof-of-concept study provides an alternative operation pattern of solar–microbial hybrid technology for future wastewater treatment from a basic but multidisciplinary view.展开更多
The mechanism of the electrolytic codeposition of Y Al alloy in molten LiF AlF 3 Al 2O 3 YF 3, LiF YF 3 Y 2O 3 AlF 3 and LiF YF 3 Y 2O 3 Al 2O 3 systems was investigated by means of cyclic volta...The mechanism of the electrolytic codeposition of Y Al alloy in molten LiF AlF 3 Al 2O 3 YF 3, LiF YF 3 Y 2O 3 AlF 3 and LiF YF 3 Y 2O 3 Al 2O 3 systems was investigated by means of cyclic voltammetry. The electrodeposited products were analysed by X ray diffraction. The results show that the electrolytic codeposition of Y Al alloy in the LiF YF 3 Y 2O 3 Al 2O 3 system without AlF 3 can be achieved at the same potential for Y(Ⅲ) and Al(Ⅲ) which have great difference in deposition potential. It is beneficial to codeposition of Y(Ⅲ) and Al(Ⅲ) when temperature rises. The potential of beginning codeposition is about -0.85 V ( vs Pt reference electrode), but only at the potential of -0.95 V or more negative can Y based Al alloy containing a great amount of yttrium be obtained.展开更多
Electrolytic copper foil has gained significant attention as an essential component in lithium-ion batteries(LIBs),printed circuit boards(PCBs),and chip packaging substrates(CPSs)applications.With the advancement of L...Electrolytic copper foil has gained significant attention as an essential component in lithium-ion batteries(LIBs),printed circuit boards(PCBs),and chip packaging substrates(CPSs)applications.With the advancement of LIBs towards higher energy densities and the increasing density of electronic components on circuits,copper foil is required to have demanding properties,such as extremely thin thickness and extremely high tensile strength.This comprehensive review firstly summarizes recent progress on the fabrication of electrolytic copper foil,and the effects of process parameters,cathode substrate,and additives on the electrodeposition behavior,microstructure,and properties of copper foil are discussed in detail.Then the regulation strategies of mechanical properties of electrolytic copper foil are also summarized,including the formation of nanotwins and texture.Furthermore,the recent advances in novel electrolytic copper foils,such as composite foils and extra-thin copper foils,are also overviewed.Lastly,the remaining challenges and perspectives on the further development of electrolytic copper foils are presented.展开更多
This study presents a novel approach to improving the anticorrosive performance of AZ31 Mg alloy by exploiting the role of the hydration reaction to induce interactions between Quinolin-8-ol(8HQ)molecules and the poro...This study presents a novel approach to improving the anticorrosive performance of AZ31 Mg alloy by exploiting the role of the hydration reaction to induce interactions between Quinolin-8-ol(8HQ)molecules and the porous MgO layer formed via plasma electrolytic oxidation(PEO).The AZ31 Mg alloy,initially coated with a PEO layer,underwent a dipping treatment in an ethanolic solution of 0.05 M 8HQ at 50℃ for 3 h.The results were compared with those from a different procedure where the PEO layer was subjected to a hydration reaction for 2 h at 90℃ before immersion in the 8HQ solution under the same conditions.The hydration treatment played a crucial role by converting MgO to Mg(OH)_(2),significantly enhancing the surface reactivity.This transformation introduced hydroxyl groups(−OH)on the surface,which facilitated donor-acceptor interactions with the electron-accepting sites on 8HQ molecules.The calculated binding energy(Ebinding)from DFT indicated that the interaction energy of 8HQ with Mg(OH)_(2) was lower compared to 8HQ with MgO,suggesting easier adsorption of 8HQ molecules on the hydrated surface.This,combined with the increased number of active sites and enhanced surface area,allowed for extensive surface coverage by 8HQ,leading to the formation of a stable,flake-like protective layer that sealed the majority of pores on the PEO layer.DFT calculations further suggested that the hydration treatment provided multiple active sites,enabling effective contact with 8HQ and rapid electron transfer,creating ideal conditions for charge-transfer-induced physical and chemical bonding.This study shows that hydration and 8HQ treatments significantly enhance the corrosion resistance of Mg alloys,highlighting their potential for advanced anticorrosive coatings.展开更多
Metal-insulator-metal aluminium electrolytic capacitors(MIM-AECs)combine high capacity-density and high breakdown field strength of solid AECs with high-frequency responsibility,wide workingtemperature window and wate...Metal-insulator-metal aluminium electrolytic capacitors(MIM-AECs)combine high capacity-density and high breakdown field strength of solid AECs with high-frequency responsibility,wide workingtemperature window and waterproof properties of MIM nanocapacitors.However,interfacial atomic diffusion poses a major obstacle,preventing the high-voltage MIM-AECs exploitation and thereby hampering their potential and advantages in high-power and high-energy-density applications.Here,an innovative high-voltage MIM-AECs were fabricated.The AlPO_(4)buffer layer is formed on AlO(OH)/AAO/Al surface by using H_(3)PO_(4)treatment,then a stable van der Waals(vdW)SnO_(2)/AlPO_(4)/AAO/Al multilayer was constructed via atomic layer deposition(ALD)technology.Due to higher diffusion barrier and lower carrier migration of SnO_(2)/AlPO_(4)/AAO interfaces,Sn atom diffusion is inhibited and carrier acceleration by electric field is weakened,guaranteeing high breakdown field strength of dielectric AAO and avoiding local breakdown risks.Through partial etching to hydrated AlO(OH)by H_(3)PO_(4)treatment,the tunnel was further opened up to facilitate subsequent ALD-SnO_(2)entry,thus obtaining a high SnO_(2)coverage.The SnO_(2)/AlPO_(4)/AAO/Al capacitors show a comprehensive performance in high-voltage(260 V),hightemperature(335℃),high-humidity(100%RH)and high-frequency response(100 k Hz),outperforming commercial solid-state AECs,and high-energy density(8.6μWh/cm^(2)),markedly exceeding previously reported MIM capacitors.The work lays the foundation for next-generation capacitors with highvoltage,high-frequency,high-temperature and high-humidity resistance.展开更多
A new perspective was reported to design the self-densified plasma electrolytic oxidation(SDF-PEO)coat-ings on magnesium alloys based on the dissolution-ionization-diffusion-deposition(DIDD)model.The main consideratio...A new perspective was reported to design the self-densified plasma electrolytic oxidation(SDF-PEO)coat-ings on magnesium alloys based on the dissolution-ionization-diffusion-deposition(DIDD)model.The main considerations of the new PEO electrolyte include the establishment of a thermodynamics diagram,the construction of a liquid-solid sintering system and the regulation of plasma sparkling kinetics.The SDF-PEO coating exhibited a homogeneous and dense microstructure,superior corrosion resistance and good technological adaptability.This work offers a novel theory to design surface treatment solutions with superior corrosion resistance and promising application prospects.展开更多
Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The tech...Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The techniques of FESEM/EDS,grazing incident beam X-ray diffraction(GIXRD),and electrochemical methods of potentiodynamic polarization and electrochemical impedance spectroscopy(EIS)were used to characterize the coatings.The results revealed that the coatings produced using the bipolar waveform exhibited lower porosity and higher thickness than those produced using the unipolar one.The corrosion performance of the specimens’cut edge was investigated using EIS after 1,8,and 12 h of immersion in a 3.5 wt.%NaCl solution.It was observed that the coating produced using the bipolar waveform demonstrated the highest corrosion resistance after 12 h of immersion,with an estimated corrosion resistance of 5.64 kΩ·cm^(2),which was approximately 3 times higher than that of the unipolar coating.Notably,no signs of galvanic corrosion were observed in the LMCs,and only minor corrosion attacks were observed on the magnesium layer in some areas.展开更多
On March 17,the PC electrolytic system of Zhangjiagang Copper Industry Co.,Ltd successfully produced the first batch of qualified PC electrolytic copper after resuming production.This company’s 100,000 t/a PC electro...On March 17,the PC electrolytic system of Zhangjiagang Copper Industry Co.,Ltd successfully produced the first batch of qualified PC electrolytic copper after resuming production.This company’s 100,000 t/a PC electrolytic copper project was completed and launched into production in April last year.展开更多
Carbon dots(CDs)are functionalized carbon-based nanomaterials that have the potential for use in advanced batteries,owing to their ultrasmall size,tunable surface functional groups and excellent dispersibility.This re...Carbon dots(CDs)are functionalized carbon-based nanomaterials that have the potential for use in advanced batteries,owing to their ultrasmall size,tunable surface functional groups and excellent dispersibility.This review summarizes recent advances in CD-based materials for advanced batteries.Methods for the preparation of CDs are first introduced,focusing on the feasibility of large-scale synthesis,and four critical uses of CDs are analyzed:electrolyte solutions,metal electrode coatings,electrode materials,and solid-state batteries.We then consider how CDs suppress dendrite formation,decrease volume expansion,accelerate charge transfer,and improve ion migration.Finally,existing problems are discussed,including the industrial production of CDs,their role as additives in the evolution of electrode interfaces,and strategies for giving them multifunctionality.展开更多
The hot deformation behavior of electrolytic copper was investigated using a Gleeble-3500 thermal simulation testing machine at temperatures ranging from 500℃ to 800℃ and strain rates ranging from 0.01 s^(-1) to 10 ...The hot deformation behavior of electrolytic copper was investigated using a Gleeble-3500 thermal simulation testing machine at temperatures ranging from 500℃ to 800℃ and strain rates ranging from 0.01 s^(-1) to 10 s^(-1),under 70% deformation conditions.The true stress-true strain curves were analyzed and a constitutive equation was established at a strain of 0.5.Based on the dynamic material model proposed by Prasad,processing maps were developed under different strain conditions.Microstructure of compressed sample was observed by electron backscatter diffraction.The results reveal that the electrolytic copper demonstrates high sensitivity to deformation temperature and strain rate during high-temperature plastic deformation.The flow stress decreases gradually with raising the temperature and reducing the strain rate.According to the established processing map,the optimal processing conditions are determined as follows:deformation temperatures of 600-650℃ and strain rates of 5-10 s^(-1).Discontinuous dynamic recrystallization of electrolytic copper occurs during high-temperature plastic deformation,and the grains are significantly refined at low temperature and high strain rate conditions.展开更多
Cellulose-based materials have attracted growing interest in the development of advanced energy storage systems owing to their intrinsic sustainability,tunable physicochemical properties,and structural versatility.Thi...Cellulose-based materials have attracted growing interest in the development of advanced energy storage systems owing to their intrinsic sustainability,tunable physicochemical properties,and structural versatility.This review systematically summarizes the key features of cellulose from the perspectives of synthesis,physicochemical characteristics,and structural design,highlighting its unique functionality and adaptability.Furthermore,the roles of cellulose in four critical battery components,i.e.,electrode,solid electrolyte interphase,separator,and electrolyte,are comprehensively discussed,emphasizing the properties aligning with the specific requirements of each component.Finally,potential research directions are proposed to guide future development.This review provides a comprehensive framework for understanding the transformative potential of cellulose in sustainable electrochemical energy storage systems as well as a guideline for future studies.展开更多
The effects of calcination temperature and mechanical ball milling on the physicochemical properties of electrolytic manganese residue(EMR),mineral phase transition,pozzolanic activity,and pore structure were studied....The effects of calcination temperature and mechanical ball milling on the physicochemical properties of electrolytic manganese residue(EMR),mineral phase transition,pozzolanic activity,and pore structure were studied.The experimental results show that the strength activity index(SAI)of 20%EMR mixed mortar at 28 days is 90.54%,95.40%,and 90.73%,respectively,after pretreatment with EMR at 800℃calcined for 3,5,and 8 min.This is mainly attributed to the high temperature decomposition of gypsum dihydrate to form activated calcium oxide.In addition,high temperature and mechanical force destroys the Si-O chemical bond and promotes the formation of calcium silicate gel structure.Due to the existence of a large number of gypsum phases in EMR mixed mortar,a large number of ettringite,C-S-H,aluminosilicate,C-A-S-H,and AFm are formed,which strongly verifies the volcanic activity of EMR.The leaching test shows that high temperature calcination has a significant effect on the stabilization of NH_(3)-N.However,the curing effect of Mn^(2+)is significant only in the calcination at 1000℃,but both Mn^(2+)and NH_(3)-N in the calcined EMR are higher than the emission standard.The encapsulation effect of EMR composite mortar provided by hydration products,and the buffering capacity of the Si-Al system for solidification of heavy metals and strong alkalis are conducive to the stability of Mn^(2+)and NH_(3)-N.After the EMR mixed mortar is aged for 3 days,Mn and NH_(3)-N are completely lower than the emission standard.In general,the EMR mixed mortar can meet the requirements for green building use.展开更多
Hydrogen production via seawater electrolysis,leveraging sustainable energy sources such as offshore wind or solar energy,has immense application potential.However,the abundance of chloride ions(Cl^(-))in seawater lea...Hydrogen production via seawater electrolysis,leveraging sustainable energy sources such as offshore wind or solar energy,has immense application potential.However,the abundance of chloride ions(Cl^(-))in seawater leads to the generation of chlorine gas and hypochlorite at the anode during electrolysis,pos-ing a severe threat of corrosion of the catalyst and electrolytic equipment.Herein,we synthesize a NiMo-based catalyst adorned with surface-anchored graphene quantum dots(GQDs).This catalyst possesses ex-cellent Cl^(-)exclusion capabilities.The Mo-NiS/Se@GQDs core-shell nanorod catalyst requires only 170 mV of overpotential to attain a current density of 10 mA cm^(-2) and operates stably for 200 h without degra-dation across a broad current density range from 100 to 400 mA cm^(-2).This remarkable electrocatalytic stability arises from the dynamic and efficient repulsion of Cl^(-)at the catalytic interface,as proven by the post-reaction analysis of Cl^(-)distribution within the catalyst.Furthermore,a potentiodynamic polarization test revealed that the Mo-NiS/Se@GQDs catalyst has high corrosion potential(0.66 V)and low corrosion current density(122.93μA cm^(-2)),underscoring its excellent corrosion resistance.This research presents a novel approach to mitigate Cl^(-)corrosion during hydrogen production through seawater electrolysis,laying a solid foundation for advancing sustainable energy conversion technologies.展开更多
This study introduced a low-temperature thermochemical method for the treatment of EMR in the presence of carbide slag(CS)to achieve an economical and efficient harmless effect.The experimental results indicate that,u...This study introduced a low-temperature thermochemical method for the treatment of EMR in the presence of carbide slag(CS)to achieve an economical and efficient harmless effect.The experimental results indicate that,under suitable conditions,the NH_(4)^(+)and Mn^(2+)contents in EMR decrease notably with the increasing CS content,accompanied by an increase in pH value.Furthermore,the concentration of NH_(4)^(+)in EMR considerably decreases with the increasing liquid-to-solid ratio,eventually stabilizing.Similarly,the pH value first increases and then decreases,ultimately stabilizing.At a CS content of 12%and a liquid-to-solid ratio of 0.7,the leaching concentrations of NH_(4)^(+)and Mn^(2+)in EMR(127.7 mg/kg and 0.15 mg/L,respectively)fall below the standard detection limit(2 mg/L),with the pH measuring 8.26,meeting the conditions outlined in the GB 8978.NH_(4)^(+)is converted to NH_(3),while Mn^(2+)is transformed into solid precipitates such as Mn(OH)_(2),Mn_(2)O_(3),MnO_(2),Ca_(3)Mn_(2)O_(7),and Ca_(2)MnO_(4).The majority of manganese ions exist in trivalent or tetravalent states and remain stable over time.The cost of using CS as a reagent for treating 1 ton of EMR is merely$1.01.The high OH^(-)concentration provided by CS enables the effective removal of NH_(4)^(+)from EMR and the solidification of Mn^(2+)during thermal reactions.展开更多
To investigate the feasibility of applying electrolytic manganese residue(EMR)in cementitious materials,an approach combining high-temperature activation(200,400,600,800 and 1000℃)and mechanical grinding(5 min)was ad...To investigate the feasibility of applying electrolytic manganese residue(EMR)in cementitious materials,an approach combining high-temperature activation(200,400,600,800 and 1000℃)and mechanical grinding(5 min)was adopted to stimulate the EMR activity.We analyzed the effect of calcination temperature on the performance of EMR with the aid of X-ray diffraction(XRD),specific surface area test(BET)and pozzolanic activity test,explored the effects of EMR activation temperature and content(0%,10%,15% and 20%)on the setting time,soundness,drying shrinkage,compressive strength,hydration products of cement-EMR mixed slurry,and assessed the effect of cement hydration on the solidification of harmful NH_(4)^(+)-N and Mn^(2+) in EMR.The research results show that high-temperature calcination can lead to the dehydration,decomposition or crystalline phase transformation of the inert sulfate and other substances in EMR,mechanical grinding can improve its particle distribution,and the coupling of the two can effectively enhance the pozzolanic activity of EMR.The decomposition and recombination of aluminum-silica phase at 800℃ optimized the EMR activity,and the strength activity index(SAI)of EMR at 28 d reached up to 95%.Appropriate calcination temperature and EMR content can ensure the workability of the mixed slurry,and when the EMR calcination temperature was 400-1000℃,the setting time of the mixed slurry under different EMR contents satisfied the specification requirements.When the calcination temperature was 600-1000℃ and EMR content was less than 20%,the soundness of the mixed slurry satisfied the specification requirements.The compressive strength of the mixed slurry increased and then decreased with the increase of activated EMR content,when the EMR content was 10%,the compressive strength of all specimens was optimal and higher than the baseline group;when the activation temperature was 800℃,the C-S-H gel in the mixed slurry interconnected with the rod-like Aft and blocked Ca(OH)_(2),and the 28 d compressive strength was increased by 14%compared with that of the baseline group.The solidification rate of Mn^(2+) in EMR by cement hydration was higher than 99%,and that of NH_(4)^(+)-N was higher than 97%.The leaching toxicity after solidification can meet the requirements of toxic emission.The results of the study may provide theoretical basis for the feasibility of the application of EMR in cementitious materials.展开更多
In this study,laser-assisted plasma electrolytic oxidation(Laser/PEO)coating was prepared on AZ31B magnesium alloy for corrosion protection,due to insufficient corrosion protection caused by the inherent defects,crack...In this study,laser-assisted plasma electrolytic oxidation(Laser/PEO)coating was prepared on AZ31B magnesium alloy for corrosion protection,due to insufficient corrosion protection caused by the inherent defects,cracks and poor quality of PEO coatings.The plasma discharge evolution,morphological characteristics,elemental composition during coating growth were characterized by high-speed camera,SEM,EDX,XRD and XPS,respectively.Meanwhile,Mott Schottky(M-S)curves,potentiodynamic polarization(PDP)curves and electrochemical impedance spectroscopy(EIS)tests characterized the oxygen vacancy defects and corrosion resistance of the coatings.The results demonstrated that laser-assisted irradiation not only induced plasma discharge on the anode surface,but also limited the plasma discharge size in the post-processing stage,which significantly increased the proportion of corrosion-resistant phase Mg_(2)SiO_(4)(the proportion of Mg_(2)SiO_(4)increased from 23.70%to 39.22%),thickness and density in the coating,and obviously reduced the oxygen vacancy defects and microcracks in the coating.As a result,the corrosion resistance of the Laser/PEO coating(9.29(±0.76)×10^(-7)A·cm^(-2))was further enhanced in comparation with the PEO coating(3.06(±0.19)×10^(-6) A·cm^(-2)).展开更多
文摘A simple general relation P = Q + R + 1 between the number P of kinds of species, the number Q of charge and elemental/core balances and the number R of independent equilibrium constants is deduced, and its validity is confirmed for non-redox and redox electrolytic systems, of different degree of complexity.
文摘In this paper, it is proved that linear combination 2·f(O)?- f(H) of elemental balances: f(O) for O and f(H) for H is linearly independent on charge and elemental/core balances for all redox systems of any degree of complexity;it is the primary form of the Generalized Electron Balance (GEB), , considered as the Approach II to GEB. The Approach II is equivalent to the Approach I based on the principle of common pool of electrons. Both Approaches are illustrated on an example of titration of acidified (H2SO4) solution of H2C2O4 with KMnO4. It is also stated, on an example of titration of the same solution with NaOH, that 2·f(O)?- f(H) is a linear combination of charge and elemental/core balances, i.e. it is not an independent balance when related to the non-redox system. These properties of 2·f(O)?- f(H) can be extended on redox and non-redox systems, of any degree of complexity, i.e. the linear independency/dependency of 2·f(O)?- f(H) on other balances related to a system in question is a criterion distinguishing redox and non-redox systems. The GEB completes the set of (charge and concentration) balances and a set of expressions for independent equilibrium constants needed for modeling the related redox system.
基金supported by the National Natural Science Foundation of China(22209006,21935001)the Natural Science Foundation of Shandong Province(ZR2022QE009)+1 种基金Fundamental Research Funds for the Central Universities(buctrc202307)the Beijing Natural Science Foundation(Z210016).
文摘Low-cost and high-safety aqueous Zn-I_(2) batteries attract extensive attention for large-scale energy storage systems.However,polyiodide shuttling and sluggish iodine conversion reactions lead to inferior rate capability and severe capacity decay.Herein,a three-dimensional polyaniline is wrapped by carboxylcarbon nanotubes(denoted as C-PANI)which is designed as a catalytic cathode to effectively boost iodine conversion with suppressed polyiodide shuttling,thereby improving Zn-I_(2) batteries.Specifically,carboxyl-carbon nanotubes serve as a proton reservoir for more protonated-NH+=sites in PANI chains,achieving a direct I0/I−reaction for suppressed polyiodide generation and Zn corrosion.Attributing to this“proton-iodine”regulation,catalytic protonated C-PANI strongly fixes electrolytic iodine species and stores proton ions simultaneously through reversible-N=/-NH^(+)-reaction.Therefore,the electrolytic Zn-I_(2) battery with C-PANI cathode exhibits an impressive capacity of 420 mAh g^(−1) and ultra-long lifespan over 40,000 cycles.Additionally,a 60 mAh pouch cell was assembled with excellent cycling stability after 100 cycles,providing new insights into exploring effective organocatalysts for superb Zn-halogen batteries.
文摘A number of studies have been reported on the use of nanocrystalline plasma electrolytic nitrocarburising technology for surface hardening of stainless steels for higher corrosion resistance resulted from this technique. However, very few studies have focused on the optimization of the nanocrystalline plasma electrolytic nitrocarburising process parameters. In this study, a design of experiment （DOE） technique, the Taguchi method, has been used to optimize the nanocrystalline plasma electrolytic nitrocarburising not only for surface hardening but also for the corrosion protection of 316L austenitic stainless steel by controlling the coating processes factors. The experimental design consisted of four factors （Urea concentration, electrical conductivity of electrolyte, voltage and duration of process）, each containing three levels. Potentiodynamic polarization measurements were carried out to determine the corrosion resistance of the coated samples. The results were analyzed with related software. An analysis of the mean of signal-to-noise （S/N） ratio indicated that the corrosion resistance of nanocrystalline plasma electrolytic nitrocarburised 316L stainless steel was influenced significantly by the levels in the Taguchi orthogonal array. The optimized coating parameters for corrosion resistance are 1150 g/L for urea concentration, 360 mS/cm for electrical conductivity of electrolyte, 260 V for applied voltage, 6 min for treatment time. The percentage of contribution for each factor was determined by the analysis of variance （ANOVA）. The results showed that the applied voltage is the most significant factor affecting the corrosion resistance of the coatings.
基金supported by the National Natural Science foundation of China(Nos.U1701243,51708184 and 51572089)Research Project of Guangdong Provincial Department of Science and Technology(No.2016B020240002)
文摘This study for the first time proposed an efficient microbial electrolyte/UV system for Methyl Orange decomposition. With an external applied voltage of 0.2 V and cathode aeration of20 mL/min, H2O2 could be in-situ generated from two-electron reduction of oxygen in cathode, reaching to 8.1 mg/L in 2 hr and continued to increase. The pollutant removal efficiency of approximate 94.7% was achieved at initial neutral pH, with the activation of ·OH in the presence of UV illumination. Although the nature of its guiding principles remain on the vista of practical exploration, this proof-of-concept study provides an alternative operation pattern of solar–microbial hybrid technology for future wastewater treatment from a basic but multidisciplinary view.
文摘The mechanism of the electrolytic codeposition of Y Al alloy in molten LiF AlF 3 Al 2O 3 YF 3, LiF YF 3 Y 2O 3 AlF 3 and LiF YF 3 Y 2O 3 Al 2O 3 systems was investigated by means of cyclic voltammetry. The electrodeposited products were analysed by X ray diffraction. The results show that the electrolytic codeposition of Y Al alloy in the LiF YF 3 Y 2O 3 Al 2O 3 system without AlF 3 can be achieved at the same potential for Y(Ⅲ) and Al(Ⅲ) which have great difference in deposition potential. It is beneficial to codeposition of Y(Ⅲ) and Al(Ⅲ) when temperature rises. The potential of beginning codeposition is about -0.85 V ( vs Pt reference electrode), but only at the potential of -0.95 V or more negative can Y based Al alloy containing a great amount of yttrium be obtained.
基金supported by the National Key R&D Plan Program of China(No.2021YFB3400800)Henan Key Research and Development Program(No.231111241000)+1 种基金the Joint Fund of Henan Province Science and Technology R&D Program(No.225200810026)Zhongyuan Scholar Workstation Funded Program(No.224400510025).
文摘Electrolytic copper foil has gained significant attention as an essential component in lithium-ion batteries(LIBs),printed circuit boards(PCBs),and chip packaging substrates(CPSs)applications.With the advancement of LIBs towards higher energy densities and the increasing density of electronic components on circuits,copper foil is required to have demanding properties,such as extremely thin thickness and extremely high tensile strength.This comprehensive review firstly summarizes recent progress on the fabrication of electrolytic copper foil,and the effects of process parameters,cathode substrate,and additives on the electrodeposition behavior,microstructure,and properties of copper foil are discussed in detail.Then the regulation strategies of mechanical properties of electrolytic copper foil are also summarized,including the formation of nanotwins and texture.Furthermore,the recent advances in novel electrolytic copper foils,such as composite foils and extra-thin copper foils,are also overviewed.Lastly,the remaining challenges and perspectives on the further development of electrolytic copper foils are presented.
基金supported by the National Research Foundation of Korea(NRF)funded by the Korean government(MSIT)(No.2022R1A2C1006743).
文摘This study presents a novel approach to improving the anticorrosive performance of AZ31 Mg alloy by exploiting the role of the hydration reaction to induce interactions between Quinolin-8-ol(8HQ)molecules and the porous MgO layer formed via plasma electrolytic oxidation(PEO).The AZ31 Mg alloy,initially coated with a PEO layer,underwent a dipping treatment in an ethanolic solution of 0.05 M 8HQ at 50℃ for 3 h.The results were compared with those from a different procedure where the PEO layer was subjected to a hydration reaction for 2 h at 90℃ before immersion in the 8HQ solution under the same conditions.The hydration treatment played a crucial role by converting MgO to Mg(OH)_(2),significantly enhancing the surface reactivity.This transformation introduced hydroxyl groups(−OH)on the surface,which facilitated donor-acceptor interactions with the electron-accepting sites on 8HQ molecules.The calculated binding energy(Ebinding)from DFT indicated that the interaction energy of 8HQ with Mg(OH)_(2) was lower compared to 8HQ with MgO,suggesting easier adsorption of 8HQ molecules on the hydrated surface.This,combined with the increased number of active sites and enhanced surface area,allowed for extensive surface coverage by 8HQ,leading to the formation of a stable,flake-like protective layer that sealed the majority of pores on the PEO layer.DFT calculations further suggested that the hydration treatment provided multiple active sites,enabling effective contact with 8HQ and rapid electron transfer,creating ideal conditions for charge-transfer-induced physical and chemical bonding.This study shows that hydration and 8HQ treatments significantly enhance the corrosion resistance of Mg alloys,highlighting their potential for advanced anticorrosive coatings.
基金supported by the National Natural Science Foundation of China(52477221,52202296)the Natural Science Foundation of Shaanxi Province(2023KXJ-246,2022JQ-048)。
文摘Metal-insulator-metal aluminium electrolytic capacitors(MIM-AECs)combine high capacity-density and high breakdown field strength of solid AECs with high-frequency responsibility,wide workingtemperature window and waterproof properties of MIM nanocapacitors.However,interfacial atomic diffusion poses a major obstacle,preventing the high-voltage MIM-AECs exploitation and thereby hampering their potential and advantages in high-power and high-energy-density applications.Here,an innovative high-voltage MIM-AECs were fabricated.The AlPO_(4)buffer layer is formed on AlO(OH)/AAO/Al surface by using H_(3)PO_(4)treatment,then a stable van der Waals(vdW)SnO_(2)/AlPO_(4)/AAO/Al multilayer was constructed via atomic layer deposition(ALD)technology.Due to higher diffusion barrier and lower carrier migration of SnO_(2)/AlPO_(4)/AAO interfaces,Sn atom diffusion is inhibited and carrier acceleration by electric field is weakened,guaranteeing high breakdown field strength of dielectric AAO and avoiding local breakdown risks.Through partial etching to hydrated AlO(OH)by H_(3)PO_(4)treatment,the tunnel was further opened up to facilitate subsequent ALD-SnO_(2)entry,thus obtaining a high SnO_(2)coverage.The SnO_(2)/AlPO_(4)/AAO/Al capacitors show a comprehensive performance in high-voltage(260 V),hightemperature(335℃),high-humidity(100%RH)and high-frequency response(100 k Hz),outperforming commercial solid-state AECs,and high-energy density(8.6μWh/cm^(2)),markedly exceeding previously reported MIM capacitors.The work lays the foundation for next-generation capacitors with highvoltage,high-frequency,high-temperature and high-humidity resistance.
基金supported by the National Natural Sci-ence Foundation of China(Nos.U21A2045 and 52201066)the Liaoning Revitalization Talents Program(No.XLYC2002071).
文摘A new perspective was reported to design the self-densified plasma electrolytic oxidation(SDF-PEO)coat-ings on magnesium alloys based on the dissolution-ionization-diffusion-deposition(DIDD)model.The main considerations of the new PEO electrolyte include the establishment of a thermodynamics diagram,the construction of a liquid-solid sintering system and the regulation of plasma sparkling kinetics.The SDF-PEO coating exhibited a homogeneous and dense microstructure,superior corrosion resistance and good technological adaptability.This work offers a novel theory to design surface treatment solutions with superior corrosion resistance and promising application prospects.
文摘Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The techniques of FESEM/EDS,grazing incident beam X-ray diffraction(GIXRD),and electrochemical methods of potentiodynamic polarization and electrochemical impedance spectroscopy(EIS)were used to characterize the coatings.The results revealed that the coatings produced using the bipolar waveform exhibited lower porosity and higher thickness than those produced using the unipolar one.The corrosion performance of the specimens’cut edge was investigated using EIS after 1,8,and 12 h of immersion in a 3.5 wt.%NaCl solution.It was observed that the coating produced using the bipolar waveform demonstrated the highest corrosion resistance after 12 h of immersion,with an estimated corrosion resistance of 5.64 kΩ·cm^(2),which was approximately 3 times higher than that of the unipolar coating.Notably,no signs of galvanic corrosion were observed in the LMCs,and only minor corrosion attacks were observed on the magnesium layer in some areas.
文摘On March 17,the PC electrolytic system of Zhangjiagang Copper Industry Co.,Ltd successfully produced the first batch of qualified PC electrolytic copper after resuming production.This company’s 100,000 t/a PC electrolytic copper project was completed and launched into production in April last year.
文摘Carbon dots(CDs)are functionalized carbon-based nanomaterials that have the potential for use in advanced batteries,owing to their ultrasmall size,tunable surface functional groups and excellent dispersibility.This review summarizes recent advances in CD-based materials for advanced batteries.Methods for the preparation of CDs are first introduced,focusing on the feasibility of large-scale synthesis,and four critical uses of CDs are analyzed:electrolyte solutions,metal electrode coatings,electrode materials,and solid-state batteries.We then consider how CDs suppress dendrite formation,decrease volume expansion,accelerate charge transfer,and improve ion migration.Finally,existing problems are discussed,including the industrial production of CDs,their role as additives in the evolution of electrode interfaces,and strategies for giving them multifunctionality.
基金Gansu Province Higher Education Institutions Industrial Support Program Project(2022CYZC-19)Gansu Provincial Science and Technology Major Project(22ZD6GA008)。
文摘The hot deformation behavior of electrolytic copper was investigated using a Gleeble-3500 thermal simulation testing machine at temperatures ranging from 500℃ to 800℃ and strain rates ranging from 0.01 s^(-1) to 10 s^(-1),under 70% deformation conditions.The true stress-true strain curves were analyzed and a constitutive equation was established at a strain of 0.5.Based on the dynamic material model proposed by Prasad,processing maps were developed under different strain conditions.Microstructure of compressed sample was observed by electron backscatter diffraction.The results reveal that the electrolytic copper demonstrates high sensitivity to deformation temperature and strain rate during high-temperature plastic deformation.The flow stress decreases gradually with raising the temperature and reducing the strain rate.According to the established processing map,the optimal processing conditions are determined as follows:deformation temperatures of 600-650℃ and strain rates of 5-10 s^(-1).Discontinuous dynamic recrystallization of electrolytic copper occurs during high-temperature plastic deformation,and the grains are significantly refined at low temperature and high strain rate conditions.
基金the funding support from University of Macao(Grant No.SRG2024-00034-IAPME)The Science and Technology Development Fund from Macao SAR(FDCT)(Grant No.0002/2024/TFP).
文摘Cellulose-based materials have attracted growing interest in the development of advanced energy storage systems owing to their intrinsic sustainability,tunable physicochemical properties,and structural versatility.This review systematically summarizes the key features of cellulose from the perspectives of synthesis,physicochemical characteristics,and structural design,highlighting its unique functionality and adaptability.Furthermore,the roles of cellulose in four critical battery components,i.e.,electrode,solid electrolyte interphase,separator,and electrolyte,are comprehensively discussed,emphasizing the properties aligning with the specific requirements of each component.Finally,potential research directions are proposed to guide future development.This review provides a comprehensive framework for understanding the transformative potential of cellulose in sustainable electrochemical energy storage systems as well as a guideline for future studies.
基金Funded by the National Natural Science Foundation of China(No.52178216)the Gansu Provincial Science and Technology Programme(No.23JRRA813)。
文摘The effects of calcination temperature and mechanical ball milling on the physicochemical properties of electrolytic manganese residue(EMR),mineral phase transition,pozzolanic activity,and pore structure were studied.The experimental results show that the strength activity index(SAI)of 20%EMR mixed mortar at 28 days is 90.54%,95.40%,and 90.73%,respectively,after pretreatment with EMR at 800℃calcined for 3,5,and 8 min.This is mainly attributed to the high temperature decomposition of gypsum dihydrate to form activated calcium oxide.In addition,high temperature and mechanical force destroys the Si-O chemical bond and promotes the formation of calcium silicate gel structure.Due to the existence of a large number of gypsum phases in EMR mixed mortar,a large number of ettringite,C-S-H,aluminosilicate,C-A-S-H,and AFm are formed,which strongly verifies the volcanic activity of EMR.The leaching test shows that high temperature calcination has a significant effect on the stabilization of NH_(3)-N.However,the curing effect of Mn^(2+)is significant only in the calcination at 1000℃,but both Mn^(2+)and NH_(3)-N in the calcined EMR are higher than the emission standard.The encapsulation effect of EMR composite mortar provided by hydration products,and the buffering capacity of the Si-Al system for solidification of heavy metals and strong alkalis are conducive to the stability of Mn^(2+)and NH_(3)-N.After the EMR mixed mortar is aged for 3 days,Mn and NH_(3)-N are completely lower than the emission standard.In general,the EMR mixed mortar can meet the requirements for green building use.
基金financially supported by the National Natural Science Foundation of China(Nos.22103045 and 52273077)the State Key Laboratory of Bio-Fibers and Eco-Textiles,Qingdao University(Nos.ZDKT202108,RZ2000003334,and G2RC202022).
文摘Hydrogen production via seawater electrolysis,leveraging sustainable energy sources such as offshore wind or solar energy,has immense application potential.However,the abundance of chloride ions(Cl^(-))in seawater leads to the generation of chlorine gas and hypochlorite at the anode during electrolysis,pos-ing a severe threat of corrosion of the catalyst and electrolytic equipment.Herein,we synthesize a NiMo-based catalyst adorned with surface-anchored graphene quantum dots(GQDs).This catalyst possesses ex-cellent Cl^(-)exclusion capabilities.The Mo-NiS/Se@GQDs core-shell nanorod catalyst requires only 170 mV of overpotential to attain a current density of 10 mA cm^(-2) and operates stably for 200 h without degra-dation across a broad current density range from 100 to 400 mA cm^(-2).This remarkable electrocatalytic stability arises from the dynamic and efficient repulsion of Cl^(-)at the catalytic interface,as proven by the post-reaction analysis of Cl^(-)distribution within the catalyst.Furthermore,a potentiodynamic polarization test revealed that the Mo-NiS/Se@GQDs catalyst has high corrosion potential(0.66 V)and low corrosion current density(122.93μA cm^(-2)),underscoring its excellent corrosion resistance.This research presents a novel approach to mitigate Cl^(-)corrosion during hydrogen production through seawater electrolysis,laying a solid foundation for advancing sustainable energy conversion technologies.
基金Funded by the Guangxi Key Research and Development Program(Guike AB23026071 and Guike AB24010020)the Guangxi Science and Technology Base and Talent Project(Guike AD24010062)the Guangxi Beibu Gulf Engineering Research Center for Green Marine Materials。
文摘This study introduced a low-temperature thermochemical method for the treatment of EMR in the presence of carbide slag(CS)to achieve an economical and efficient harmless effect.The experimental results indicate that,under suitable conditions,the NH_(4)^(+)and Mn^(2+)contents in EMR decrease notably with the increasing CS content,accompanied by an increase in pH value.Furthermore,the concentration of NH_(4)^(+)in EMR considerably decreases with the increasing liquid-to-solid ratio,eventually stabilizing.Similarly,the pH value first increases and then decreases,ultimately stabilizing.At a CS content of 12%and a liquid-to-solid ratio of 0.7,the leaching concentrations of NH_(4)^(+)and Mn^(2+)in EMR(127.7 mg/kg and 0.15 mg/L,respectively)fall below the standard detection limit(2 mg/L),with the pH measuring 8.26,meeting the conditions outlined in the GB 8978.NH_(4)^(+)is converted to NH_(3),while Mn^(2+)is transformed into solid precipitates such as Mn(OH)_(2),Mn_(2)O_(3),MnO_(2),Ca_(3)Mn_(2)O_(7),and Ca_(2)MnO_(4).The majority of manganese ions exist in trivalent or tetravalent states and remain stable over time.The cost of using CS as a reagent for treating 1 ton of EMR is merely$1.01.The high OH^(-)concentration provided by CS enables the effective removal of NH_(4)^(+)from EMR and the solidification of Mn^(2+)during thermal reactions.
基金Funded by the Science and Technology Program of Gansu Province(No.25CXGA070)。
文摘To investigate the feasibility of applying electrolytic manganese residue(EMR)in cementitious materials,an approach combining high-temperature activation(200,400,600,800 and 1000℃)and mechanical grinding(5 min)was adopted to stimulate the EMR activity.We analyzed the effect of calcination temperature on the performance of EMR with the aid of X-ray diffraction(XRD),specific surface area test(BET)and pozzolanic activity test,explored the effects of EMR activation temperature and content(0%,10%,15% and 20%)on the setting time,soundness,drying shrinkage,compressive strength,hydration products of cement-EMR mixed slurry,and assessed the effect of cement hydration on the solidification of harmful NH_(4)^(+)-N and Mn^(2+) in EMR.The research results show that high-temperature calcination can lead to the dehydration,decomposition or crystalline phase transformation of the inert sulfate and other substances in EMR,mechanical grinding can improve its particle distribution,and the coupling of the two can effectively enhance the pozzolanic activity of EMR.The decomposition and recombination of aluminum-silica phase at 800℃ optimized the EMR activity,and the strength activity index(SAI)of EMR at 28 d reached up to 95%.Appropriate calcination temperature and EMR content can ensure the workability of the mixed slurry,and when the EMR calcination temperature was 400-1000℃,the setting time of the mixed slurry under different EMR contents satisfied the specification requirements.When the calcination temperature was 600-1000℃ and EMR content was less than 20%,the soundness of the mixed slurry satisfied the specification requirements.The compressive strength of the mixed slurry increased and then decreased with the increase of activated EMR content,when the EMR content was 10%,the compressive strength of all specimens was optimal and higher than the baseline group;when the activation temperature was 800℃,the C-S-H gel in the mixed slurry interconnected with the rod-like Aft and blocked Ca(OH)_(2),and the 28 d compressive strength was increased by 14%compared with that of the baseline group.The solidification rate of Mn^(2+) in EMR by cement hydration was higher than 99%,and that of NH_(4)^(+)-N was higher than 97%.The leaching toxicity after solidification can meet the requirements of toxic emission.The results of the study may provide theoretical basis for the feasibility of the application of EMR in cementitious materials.
基金The National Natural Science Foundation of China(U2130122,U22A20199,and 51975533)Natural Science Foundation of Zhejiang Province(LGJ22E050002)+1 种基金Equipment pre-research joint fund project of the Ministry of Education(8091B022215)China Postdoctoral Science Foundation(2023M733147)funded this research.
文摘In this study,laser-assisted plasma electrolytic oxidation(Laser/PEO)coating was prepared on AZ31B magnesium alloy for corrosion protection,due to insufficient corrosion protection caused by the inherent defects,cracks and poor quality of PEO coatings.The plasma discharge evolution,morphological characteristics,elemental composition during coating growth were characterized by high-speed camera,SEM,EDX,XRD and XPS,respectively.Meanwhile,Mott Schottky(M-S)curves,potentiodynamic polarization(PDP)curves and electrochemical impedance spectroscopy(EIS)tests characterized the oxygen vacancy defects and corrosion resistance of the coatings.The results demonstrated that laser-assisted irradiation not only induced plasma discharge on the anode surface,but also limited the plasma discharge size in the post-processing stage,which significantly increased the proportion of corrosion-resistant phase Mg_(2)SiO_(4)(the proportion of Mg_(2)SiO_(4)increased from 23.70%to 39.22%),thickness and density in the coating,and obviously reduced the oxygen vacancy defects and microcracks in the coating.As a result,the corrosion resistance of the Laser/PEO coating(9.29(±0.76)×10^(-7)A·cm^(-2))was further enhanced in comparation with the PEO coating(3.06(±0.19)×10^(-6) A·cm^(-2)).
