Plasma electrolyte oxidation(PEO)is a surface treatment method with high dependency on the process parameters.This paper focuses on maximizing the corrosion resistance of PEO coatings applied on Mg-5Zn-0.4Ca(ZX504)all...Plasma electrolyte oxidation(PEO)is a surface treatment method with high dependency on the process parameters.This paper focuses on maximizing the corrosion resistance of PEO coatings applied on Mg-5Zn-0.4Ca(ZX504)alloy by optimizing the process parameiers.For this purpose,the Taguchi method based on LI8 orthogonal array with mixed level design was used for optimization and determining effective parameters.Main process factors including electrolyte concentration,current density,frequency and duty cycle were considered at different levels.The corrosion resistance,as the performance indicator,was obtained using electrochemical impedance spectroscopy technique.Surface characteristics were also evaluated using SEM(scanning electron microscopy),EDS(energy dispersive spectroscopy),profilometer and contact angle goniometer.The statistical analysis showed that the optimum condition could be obtained at a current density of 200 mA/cm^2,frequency of 500Hz and at a duty cycle of 30%,in an electrolyle containing 15 g/L NazPO·12H2O and 10g/L KF.展开更多
Plasma electrolytic oxidation(PEO)is considered as a cost effective and environmentally friendly surface treatmentprocess for improving surface properties of light alloys.The formation of ceramic coatings on Ti6Al4V a...Plasma electrolytic oxidation(PEO)is considered as a cost effective and environmentally friendly surface treatmentprocess for improving surface properties of light alloys.The formation of ceramic coatings on Ti6Al4V alloy was reported bytwo-step PEO process and its structural,electrochemical and mechanical properties with the coated samples were compared byone-step PEO process in an alkaline electrolyte.The structural properties were studied using field-emission scanning microscope(FESEM)and X-ray diffraction(XRD).Electrochemical studies were carried out using linear polarization method and in additionmechanical behaviors were investigated by means of Knoop microhardness and nanoindentation method.Results showed that thesecond step process resulted in an increase of both porosity percentage and average pore diameter on the surface.The two-stepprocess resulted in a small increase of thickness from about12.5to13.0μm.Electrochemical test results showed that applying thesecond step resulted in the decrease of both polarization resistance from1800.2to412.5kΩ/cm2and protection efficiency from97.8%to90.5%.Finally,the nanoindentation results indicated that the PEO coatings became softer but more ductile after applyingthe second processing step in acidic electrolyte.展开更多
A new perspective was reported to design the self-densified plasma electrolytic oxidation(SDF-PEO)coat-ings on magnesium alloys based on the dissolution-ionization-diffusion-deposition(DIDD)model.The main consideratio...A new perspective was reported to design the self-densified plasma electrolytic oxidation(SDF-PEO)coat-ings on magnesium alloys based on the dissolution-ionization-diffusion-deposition(DIDD)model.The main considerations of the new PEO electrolyte include the establishment of a thermodynamics diagram,the construction of a liquid-solid sintering system and the regulation of plasma sparkling kinetics.The SDF-PEO coating exhibited a homogeneous and dense microstructure,superior corrosion resistance and good technological adaptability.This work offers a novel theory to design surface treatment solutions with superior corrosion resistance and promising application prospects.展开更多
This study presents a novel approach to improving the anticorrosive performance of AZ31 Mg alloy by exploiting the role of the hydration reaction to induce interactions between Quinolin-8-ol(8HQ)molecules and the poro...This study presents a novel approach to improving the anticorrosive performance of AZ31 Mg alloy by exploiting the role of the hydration reaction to induce interactions between Quinolin-8-ol(8HQ)molecules and the porous MgO layer formed via plasma electrolytic oxidation(PEO).The AZ31 Mg alloy,initially coated with a PEO layer,underwent a dipping treatment in an ethanolic solution of 0.05 M 8HQ at 50℃ for 3 h.The results were compared with those from a different procedure where the PEO layer was subjected to a hydration reaction for 2 h at 90℃ before immersion in the 8HQ solution under the same conditions.The hydration treatment played a crucial role by converting MgO to Mg(OH)_(2),significantly enhancing the surface reactivity.This transformation introduced hydroxyl groups(−OH)on the surface,which facilitated donor-acceptor interactions with the electron-accepting sites on 8HQ molecules.The calculated binding energy(Ebinding)from DFT indicated that the interaction energy of 8HQ with Mg(OH)_(2) was lower compared to 8HQ with MgO,suggesting easier adsorption of 8HQ molecules on the hydrated surface.This,combined with the increased number of active sites and enhanced surface area,allowed for extensive surface coverage by 8HQ,leading to the formation of a stable,flake-like protective layer that sealed the majority of pores on the PEO layer.DFT calculations further suggested that the hydration treatment provided multiple active sites,enabling effective contact with 8HQ and rapid electron transfer,creating ideal conditions for charge-transfer-induced physical and chemical bonding.This study shows that hydration and 8HQ treatments significantly enhance the corrosion resistance of Mg alloys,highlighting their potential for advanced anticorrosive coatings.展开更多
Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The tech...Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The techniques of FESEM/EDS,grazing incident beam X-ray diffraction(GIXRD),and electrochemical methods of potentiodynamic polarization and electrochemical impedance spectroscopy(EIS)were used to characterize the coatings.The results revealed that the coatings produced using the bipolar waveform exhibited lower porosity and higher thickness than those produced using the unipolar one.The corrosion performance of the specimens’cut edge was investigated using EIS after 1,8,and 12 h of immersion in a 3.5 wt.%NaCl solution.It was observed that the coating produced using the bipolar waveform demonstrated the highest corrosion resistance after 12 h of immersion,with an estimated corrosion resistance of 5.64 kΩ·cm^(2),which was approximately 3 times higher than that of the unipolar coating.Notably,no signs of galvanic corrosion were observed in the LMCs,and only minor corrosion attacks were observed on the magnesium layer in some areas.展开更多
In this study,laser-assisted plasma electrolytic oxidation(Laser/PEO)coating was prepared on AZ31B magnesium alloy for corrosion protection,due to insufficient corrosion protection caused by the inherent defects,crack...In this study,laser-assisted plasma electrolytic oxidation(Laser/PEO)coating was prepared on AZ31B magnesium alloy for corrosion protection,due to insufficient corrosion protection caused by the inherent defects,cracks and poor quality of PEO coatings.The plasma discharge evolution,morphological characteristics,elemental composition during coating growth were characterized by high-speed camera,SEM,EDX,XRD and XPS,respectively.Meanwhile,Mott Schottky(M-S)curves,potentiodynamic polarization(PDP)curves and electrochemical impedance spectroscopy(EIS)tests characterized the oxygen vacancy defects and corrosion resistance of the coatings.The results demonstrated that laser-assisted irradiation not only induced plasma discharge on the anode surface,but also limited the plasma discharge size in the post-processing stage,which significantly increased the proportion of corrosion-resistant phase Mg_(2)SiO_(4)(the proportion of Mg_(2)SiO_(4)increased from 23.70%to 39.22%),thickness and density in the coating,and obviously reduced the oxygen vacancy defects and microcracks in the coating.As a result,the corrosion resistance of the Laser/PEO coating(9.29(±0.76)×10^(-7)A·cm^(-2))was further enhanced in comparation with the PEO coating(3.06(±0.19)×10^(-6) A·cm^(-2)).展开更多
Electrolyte selection for Plasma Electrolytic Oxidation(PEO)of magnesium is important as this determines composition,morphology and properties of resultant coatings that are urgently sought after for protection of Mg ...Electrolyte selection for Plasma Electrolytic Oxidation(PEO)of magnesium is important as this determines composition,morphology and properties of resultant coatings that are urgently sought after for protection of Mg alloys from corrosion and wear in harsh environments.However,electrolyte design is often performed heuristically,which hampers the development and optimisation of new PEO processes.Here,we attempt to achieve a mechanistic understanding of electrochemical and microstructural aspects of anodic films evolution at the prebreakdown stages of PEO treatments of magnesium in aqueous alkaline solutions of NaAlO_(2),Na_(3)PO_(4),Na F and Na_(2)SiO_(3).Systematic studies have shown that magnesium self-passivation by MgO/Mg(OH)_(2)can be compromised by both chemical and mechanical instabilities developed due to side effects of anodic reactions.Stable initiation of PEO process requires maintaining surface passivity in a wide range of p H,which can be achieved only by combining self-depositing passivators with those binding dissolved magnesium into insoluble compounds.展开更多
The corrosion resistance of magnesium alloys is a significant concern in industries seeking to use these materials for lightweight structures.Plasma electrolytic oxidation(PEO)is a process that forms a ceramic oxide f...The corrosion resistance of magnesium alloys is a significant concern in industries seeking to use these materials for lightweight structures.Plasma electrolytic oxidation(PEO)is a process that forms a ceramic oxide film on Mg alloy surfaces,effectively enhancing their corrosion performance in the short term.In this regard,optimizing PEO process parameters is crucial for creating a stable oxide layer.An improved level of corrosion resistance is ensured by applying superhydrophobic coating(SHC)on top of the PEO layer to prevent moisture infiltration,creating air pockets on the surface.Various methods are employed to fabricate SHC on Mg alloys,including techniques like electrophoretic deposition(EPD),Hydrothermal(HT),dip,and spray coating.The synergistic combination of PEO and SHC coatings has demonstrated encouraging outcomes in enhancing the corrosion performance of Mg alloys.This study offers an extensive overview of recent progress in the preparation,characterization,and corrosion behavior of Mg alloys by employing PEO coatings and SHC treatment processes.展开更多
A novel type of microcapsule-encapsulated corrosion inhibitor was prepared in a water-based solution with a pH range of 7-8,and it was applied to the composite organic coating of magnesium alloy plasma electrolytic ox...A novel type of microcapsule-encapsulated corrosion inhibitor was prepared in a water-based solution with a pH range of 7-8,and it was applied to the composite organic coating of magnesium alloy plasma electrolytic oxidation to enhance its corrosion resistance and self-healing properties.The morphology,chemical composition,structure,and functional properties of the composite coating were investigated by scanning electron microscopy(SEM),energy dispersive X-ray spectroscopy(EDS),Fourier transform infrared spectroscopy(FTIR),polarization curve,alternating current impedance,and salt immersion test.The experimental results showed that,after immersion in a 3.5 wt%NaCl solution for 12 h,the coating could effectively protect AZ91D from corrosion.When the coating was damaged,the exposed alloy surface would release metal ions in the corrosive environment and react with the corrosion inhibitor 8-hydroxyquinoline to form a Mg(8-HQ)_(2) chelate,exhibiting significant self-healing behavior.The study results demonstrate the broad application prospects of microcapsule technology in the coating field,providing new ideas for the development of efficient anti-corrosion coatings.展开更多
Plasma electrolytic oxidation of a cast A356 aluminum alloy was carried out in aluminate electrolytes to develop wear and corrosion resistant coatings. Different concentrations of 2, 16 and 24 g/L NaAlO2 solutions and...Plasma electrolytic oxidation of a cast A356 aluminum alloy was carried out in aluminate electrolytes to develop wear and corrosion resistant coatings. Different concentrations of 2, 16 and 24 g/L NaAlO2 solutions and a silicate electrolyte （for comparison） were employed for the investigation. Wear performance and corrosion resistance of the coatings were evaluated by WC （tungsten carbide） ball-on-flat dry sliding tests and electrochemical methods, respectively. The results show that the coating formed for a short duration of 480 s in 24 g/L NaAlO2 solution generated the best protection. The coating sustained 30 N load for sliding time of 1800 s, showing very low wear rate of -4.5×10^-7 mm3/（N· m）. A low corrosion current density of -8.81×10^-9 A/cm2 was also recorded. Despite low α-Al2O3 content of the coating, the compact and nearly single layer nature of the coating guaranteed the excellent performances.展开更多
As an efficient surface modification approach,the plasma electrolytic oxidation(PEO)technique can boost the capability of wear protection in Mg and its alloys by applying a hard and thick ceramic coating.In this proce...As an efficient surface modification approach,the plasma electrolytic oxidation(PEO)technique can boost the capability of wear protection in Mg and its alloys by applying a hard and thick ceramic coating.In this procedure,more efficient protection can be acquired via adding additives(in the form of particle,powder,sheet,etc.)into solutions and producing composite coatings.These additives result in more efficient protection against wear via getting stuck in the cracks and pores of coatings and rising the thickness,hardness,and diminishing the porosity size and content.The efficiency of each additive can be changed owing to its intrinsic properties like melting point,size,participation type(reactive,partly reactive,or inert)and potential of zeta.In this review,the effects of distinct additives in nano-and micro-scale size on wear behavior of PEO coatings on Mg and its alloys is going to be reviewed.展开更多
Plasma electrolytic oxidation(PEO)coatings were prepared on AZ91D magnesium alloys in alkaline silicate-based electrolyte with and without additives.The mutual effects among additives including TiC particles,dispersan...Plasma electrolytic oxidation(PEO)coatings were prepared on AZ91D magnesium alloys in alkaline silicate-based electrolyte with and without additives.The mutual effects among additives including TiC particles,dispersant polyethylene glycol 6000(PEG6000)and anionic surfactant sodium dodecyl sulfate(SDS)were studied based on orthogonal experiment.The content and distribution of TiC deposited in the coatings were measured by EPMA and EDS.The thicknesses,phase compositions,microstructures and corrosion resistances of the codlings were cAarnined by using TT260 eddy current tuickncss gage,XRD,SEM and clcctrochcniical test,respectively.The results show that the experiment design of this study is the key to study the mutual effects among these additives.Each additive and their interactions all remarkably influence TiC content and corrosion resistance of the coatings.Smaller size TiC is much easier to migrate towards the anode,and the interaction between PEG6000 and SDS both effectively prevents its agglomeration and increases the number of its negative surface charges,which further increase the migration rate and the deposited uniformity of TiC and make TiC have more opportunity to deposit in the discharge channel.Thus,when smaller size TiC,PEG6000 and SDS are all added into the electrolyte,they could improve the anti-corrosion property of the coating to the largest extent attributed to higher TiC content and the densest microstructure of the coating.展开更多
Plasma electrolytic oxidation(PEO)of cast A356 aluminum alloy was carried out in 32 g/L NaAlO_(2) with the addition of different concentrations of NaOH.The stability of the aluminate solution is greatly enhanced by in...Plasma electrolytic oxidation(PEO)of cast A356 aluminum alloy was carried out in 32 g/L NaAlO_(2) with the addition of different concentrations of NaOH.The stability of the aluminate solution is greatly enhanced by increasing the concentration of NaOH.However,corresponding changes in the PEO behaviour occur due to the increment of NaOH concentration.Thicker precursor coatings are required for the PEO treatment in a more concentrated NaOH electrolyte.The results show that the optimal NaOH concentration is 5 g/L,which improves the stability of storage electrolyte to about 35 days,and leads to dense coatings with high wear performance(wear rate:4.1×10^(−7) mm^(3)·N^(−1)·m^(−1)).展开更多
Plasma electrolytic oxidation(PEO) of brass was carried out in aluminate electrolytes with the addition of NaH2PO4(S1) and Na2SiO3(S2), respectively, with the aim to investigate the effect of additives on the coating ...Plasma electrolytic oxidation(PEO) of brass was carried out in aluminate electrolytes with the addition of NaH2PO4(S1) and Na2SiO3(S2), respectively, with the aim to investigate the effect of additives on the coating formation and corrosion resistance. For the PEO in S1 electrolyte, a mixed layer of AlPO4and Al2O3is formed at the initial stage, which leads to fast plasma discharges and formation of black coatings with the compositions of Al2O3,CuO, Cu2O and ZnO. However, in S2 electrolyte, plasma discharges are delayed and the coatings show a reddish color due to more Cu2O. Mott-Schottky tests show that the S1 coatings are p-type semiconductors;while the S2 coatings can be adjusted between n-type and p-type. Potentiodynamic polarization and electrochemical impedance spectroscopy(EIS) tests show that the PEO treatment can significantly improve the corrosion resistance of brass, with protection efficiency up to 91.50% and the largest charge transfer resistance of 59.95 kΩ·cm^(2) for the S1 coating.展开更多
The formation of protective multifunctional coatings on magnesium alloy MA8 using plasma electrolyt- ic oxidation （PEO） in an electrolytic system containing nanosized particles of titanium nitride was investigated. ...The formation of protective multifunctional coatings on magnesium alloy MA8 using plasma electrolyt- ic oxidation （PEO） in an electrolytic system containing nanosized particles of titanium nitride was investigated. Electrochemical and mechanical properties of the obtained layers were examined. It was established that microhardness of the coating with the nanoparticle concentration of 3 gl-1 increased twofold （4.2 ± 0.5 GPa）, while wear resistance decreased （4.97 × 10-6 mm3 N-1 m-1）, as compared to re- spective values for the PEO-coating formed in the electrolyte without nanoparticles （2.1 ± 0.3 GPa, 1.12 × 10.5 mm3 N-1 m-1）.展开更多
In this study,ceramic coatings were deposited on 6061 Al alloy using a plasma electrolytic oxidation（PEO）technique,and the effect of concentrations of KOH and Na_2SiO_3 as electrolytes for PEO process was studied on...In this study,ceramic coatings were deposited on 6061 Al alloy using a plasma electrolytic oxidation（PEO）technique,and the effect of concentrations of KOH and Na_2SiO_3 as electrolytes for PEO process was studied on microstructure,chemical composition,and electrochemical behavior of PEO coatings formed on the 6061 Al alloy.The results indicated that the increase in concentration of KOH led to rise in electrical conductivity of electrolyte.Consequently,the breakdown voltage reduced,which in turn improved the surface quality and the corrosion behavior.Moreover,the increase in concentration of Na_2SiO_3 resulted in the increase in incorporation of Si in the coating,which led to a higher corrosion potential in the concentration of 4 g L^（-1）.According to this investigation,the best protection behavior of coatings can be obtained when the KOH and Na_2SiO_3 concentrations in PEO electrolyte are equal to 4 g L^（-1）.展开更多
Plasma electrolytic oxidation（PEO） coatings were prepared on AZ31 magnesium alloy using alkaline phosphate as base electrolyte system, and with the addition of sodium silicate（Na2SiO3）, sodium aluminate（NaAlO2） ...Plasma electrolytic oxidation（PEO） coatings were prepared on AZ31 magnesium alloy using alkaline phosphate as base electrolyte system, and with the addition of sodium silicate（Na2SiO3）, sodium aluminate（NaAlO2） and potassium fluorozirconate（K2ZrF6） as additives. The microstructure, phase composition and element composition as well as surface profile of the PEO coatings were analyzed by means of scanning electron microscopy（SEM）, X-ray diffraction（XRD）, energy dispersive X-ray spectroscopy（EDS）, and threedimensional（3 D） optical profilometry. The corrosion and wear properties were evaluated by electrochemical potentiodynamic polarization in 3.5 wt% Na Cl solution and ball-on-disc wear tests, respectively. The results showed that the anions of the additives effectively participated in the coating formation influencing its microstructural features, chemical composition, corrosion resistance and tribological behaviour. It was observed that the sample treated by PEO in the electrolyte solution containing K2ZrF6 as an additive showed better corrosion and abrasive resistance.展开更多
To enhance the long-term corrosion resistance of the plasma electrolytic oxidation(PEO)coating on the magnesium(Mg)alloy,an inorganic salt combined with corrosion inhibitors was used for posttreatment of the coating.I...To enhance the long-term corrosion resistance of the plasma electrolytic oxidation(PEO)coating on the magnesium(Mg)alloy,an inorganic salt combined with corrosion inhibitors was used for posttreatment of the coating.In this study,the corrosion performance of PEO-coated AM50 Mg was significantly improved by loading sodium lauryl sulfonate(SDS)and sodium dodecyl benzene sulf-onate into Ba(NO_(3))_(2) post-sealing solutions.Scanning electron microscopy,X-ray photoelectron spectroscopy,X-ray diffraction,Fourier transform infrared spectrometer,and ultraviolet-visible analyses showed that the inhibitors enhanced the incorporation of BaO_(2) into PEO coatings.Electrochemical impedance showed that post-sealing in Ba(NO_(3))_(2)/SDS treatment enhanced corrosion resistance by three orders of magnitude.The total impedance value remained at 926Ω·cm^(2)after immersing in a 0.5wt%NaCl solution for 768 h.A salt spray test for 40 days did not show any obvious region of corrosion,proving excellent post-sealing by Ba(NO_(3))_(2)/SDS treatment.The corrosion resistance of the coating was enhanced through the synergistic effect of BaO2 pore sealing and SDS adsorption.展开更多
The favorable properties of Mg alloys,such as their lightweight and robust nature,are driving an increase in interest in their development for industrial and biomedical applications.These benefits aren’t enough to ma...The favorable properties of Mg alloys,such as their lightweight and robust nature,are driving an increase in interest in their development for industrial and biomedical applications.These benefits aren’t enough to make them widely used;problems like poor corrosion resistance and no antibacterial qualities call attention to the need for improved coating methods.Because of its distinct characteristics and efficacy in surface modification,plasma electrolytic oxidation(PEO)has emerged as a preferred coating process.But protective coatings can only become better with time if we keep pushing them to new limits.PEO coatings on Mg alloys may be made more protective by using metal-organic frameworks(MOFs).Hybrid crystalline MOFs have been popular in inorganic and organic chemistry in recent decades.These complexes include organic ligands and metal ions or clusters.Large specific surface areas,customizable topologies and functionalities,ordered pore structures,and many reactive sites make these materials famous.Preventing corrosion using MOFs seems promising.This study analyzes MOF-led corrosion protection material advances and their efficacy in tackling corrosion challenges.A comprehensive review of numerous production techniques employed with MOFs for corrosion protection highlights their pros and cons.The report also discusses MOFs’potential corrosion-prevention functions and the challenges that must be overcome to make them viable.The corrosion-preventive ways of MOFs as inhibitors,nano-fillers,nano-containers,and surface-coating agents are also examined.As we conclude our detailed analysis,we provide a future-oriented vision of MOFs’undiscovered corrosion prevention potential.This exposition illustrates corrosion protection material advances employing cutting-edge MOF-based anticorrosion breakthroughs.It encourages creative ways to corrosion protection’s future.展开更多
In the present research,the NaF assisted plasma electrolytic oxidation(PEO)is designed to fabricate the high-content ZnO nanoparti-cles doped coating on AZ31B alloy.The microstructure,phase constituents and corrosion ...In the present research,the NaF assisted plasma electrolytic oxidation(PEO)is designed to fabricate the high-content ZnO nanoparti-cles doped coating on AZ31B alloy.The microstructure,phase constituents and corrosion behavior of the PEO coatings are investigated systematically.The results reveal that the introduction of NaF promotes the formation of MgF2 nanophases in the passivation layer on Mg alloy,decreasing the breakdown voltage and discharge voltage.As a result,the continuous arcing caused by high discharge voltage is alleviated.With the increasing of NaF content,the Zn content in the PEO coating is enhanced and the pore size in the coating is decreased correspondingly.Due to the high-content ZnO doping,the PEO coating protected AZ31B alloy demonstrates the better corrosion resistance.Compared with the bare AZ31B alloy,the high-content ZnO doped PEO coated sample shows an increased corrosion potential from-1.465 V to-1.008 V,a decreased corrosion current density from 3.043×10^(-5) A·cm^(-2) to 3.960×10^(-8) A·cm^(-2) and an increased charge transfer resistance from 1.213×10^(2) ohm·cm^(2) to 2.598×10^(5) ohm·cm^(2).Besides,the high-content ZnO doped PEO coated sample also has the excellent corrosion resistance in salt solution,exhibiting no obvious corrosion after more than 2000 h neutral salt spraying and 28 days’immersion testing.The improved corrosion resistance can be ascribed to the relative uniform distribution of ZnO in PEO coating which can transform to Zn(OH)2 and form a continuous protective layer along the corrosion interface.展开更多
文摘Plasma electrolyte oxidation(PEO)is a surface treatment method with high dependency on the process parameters.This paper focuses on maximizing the corrosion resistance of PEO coatings applied on Mg-5Zn-0.4Ca(ZX504)alloy by optimizing the process parameiers.For this purpose,the Taguchi method based on LI8 orthogonal array with mixed level design was used for optimization and determining effective parameters.Main process factors including electrolyte concentration,current density,frequency and duty cycle were considered at different levels.The corrosion resistance,as the performance indicator,was obtained using electrochemical impedance spectroscopy technique.Surface characteristics were also evaluated using SEM(scanning electron microscopy),EDS(energy dispersive spectroscopy),profilometer and contact angle goniometer.The statistical analysis showed that the optimum condition could be obtained at a current density of 200 mA/cm^2,frequency of 500Hz and at a duty cycle of 30%,in an electrolyle containing 15 g/L NazPO·12H2O and 10g/L KF.
基金International affairs department of University of Tehran and Sarkhoon & Qeshm Gas Treating Company for the financial support of this study
文摘Plasma electrolytic oxidation(PEO)is considered as a cost effective and environmentally friendly surface treatmentprocess for improving surface properties of light alloys.The formation of ceramic coatings on Ti6Al4V alloy was reported bytwo-step PEO process and its structural,electrochemical and mechanical properties with the coated samples were compared byone-step PEO process in an alkaline electrolyte.The structural properties were studied using field-emission scanning microscope(FESEM)and X-ray diffraction(XRD).Electrochemical studies were carried out using linear polarization method and in additionmechanical behaviors were investigated by means of Knoop microhardness and nanoindentation method.Results showed that thesecond step process resulted in an increase of both porosity percentage and average pore diameter on the surface.The two-stepprocess resulted in a small increase of thickness from about12.5to13.0μm.Electrochemical test results showed that applying thesecond step resulted in the decrease of both polarization resistance from1800.2to412.5kΩ/cm2and protection efficiency from97.8%to90.5%.Finally,the nanoindentation results indicated that the PEO coatings became softer but more ductile after applyingthe second processing step in acidic electrolyte.
基金supported by the National Natural Sci-ence Foundation of China(Nos.U21A2045 and 52201066)the Liaoning Revitalization Talents Program(No.XLYC2002071).
文摘A new perspective was reported to design the self-densified plasma electrolytic oxidation(SDF-PEO)coat-ings on magnesium alloys based on the dissolution-ionization-diffusion-deposition(DIDD)model.The main considerations of the new PEO electrolyte include the establishment of a thermodynamics diagram,the construction of a liquid-solid sintering system and the regulation of plasma sparkling kinetics.The SDF-PEO coating exhibited a homogeneous and dense microstructure,superior corrosion resistance and good technological adaptability.This work offers a novel theory to design surface treatment solutions with superior corrosion resistance and promising application prospects.
基金supported by the National Research Foundation of Korea(NRF)funded by the Korean government(MSIT)(No.2022R1A2C1006743).
文摘This study presents a novel approach to improving the anticorrosive performance of AZ31 Mg alloy by exploiting the role of the hydration reaction to induce interactions between Quinolin-8-ol(8HQ)molecules and the porous MgO layer formed via plasma electrolytic oxidation(PEO).The AZ31 Mg alloy,initially coated with a PEO layer,underwent a dipping treatment in an ethanolic solution of 0.05 M 8HQ at 50℃ for 3 h.The results were compared with those from a different procedure where the PEO layer was subjected to a hydration reaction for 2 h at 90℃ before immersion in the 8HQ solution under the same conditions.The hydration treatment played a crucial role by converting MgO to Mg(OH)_(2),significantly enhancing the surface reactivity.This transformation introduced hydroxyl groups(−OH)on the surface,which facilitated donor-acceptor interactions with the electron-accepting sites on 8HQ molecules.The calculated binding energy(Ebinding)from DFT indicated that the interaction energy of 8HQ with Mg(OH)_(2) was lower compared to 8HQ with MgO,suggesting easier adsorption of 8HQ molecules on the hydrated surface.This,combined with the increased number of active sites and enhanced surface area,allowed for extensive surface coverage by 8HQ,leading to the formation of a stable,flake-like protective layer that sealed the majority of pores on the PEO layer.DFT calculations further suggested that the hydration treatment provided multiple active sites,enabling effective contact with 8HQ and rapid electron transfer,creating ideal conditions for charge-transfer-induced physical and chemical bonding.This study shows that hydration and 8HQ treatments significantly enhance the corrosion resistance of Mg alloys,highlighting their potential for advanced anticorrosive coatings.
文摘Plasma electrolytic oxidation(PEO)coatings were prepared on Al−Mg laminated macro composites(LMCs)using both unipolar and bipolar waveforms in an appropriate electrolyte for both aluminum and magnesium alloys.The techniques of FESEM/EDS,grazing incident beam X-ray diffraction(GIXRD),and electrochemical methods of potentiodynamic polarization and electrochemical impedance spectroscopy(EIS)were used to characterize the coatings.The results revealed that the coatings produced using the bipolar waveform exhibited lower porosity and higher thickness than those produced using the unipolar one.The corrosion performance of the specimens’cut edge was investigated using EIS after 1,8,and 12 h of immersion in a 3.5 wt.%NaCl solution.It was observed that the coating produced using the bipolar waveform demonstrated the highest corrosion resistance after 12 h of immersion,with an estimated corrosion resistance of 5.64 kΩ·cm^(2),which was approximately 3 times higher than that of the unipolar coating.Notably,no signs of galvanic corrosion were observed in the LMCs,and only minor corrosion attacks were observed on the magnesium layer in some areas.
基金The National Natural Science Foundation of China(U2130122,U22A20199,and 51975533)Natural Science Foundation of Zhejiang Province(LGJ22E050002)+1 种基金Equipment pre-research joint fund project of the Ministry of Education(8091B022215)China Postdoctoral Science Foundation(2023M733147)funded this research.
文摘In this study,laser-assisted plasma electrolytic oxidation(Laser/PEO)coating was prepared on AZ31B magnesium alloy for corrosion protection,due to insufficient corrosion protection caused by the inherent defects,cracks and poor quality of PEO coatings.The plasma discharge evolution,morphological characteristics,elemental composition during coating growth were characterized by high-speed camera,SEM,EDX,XRD and XPS,respectively.Meanwhile,Mott Schottky(M-S)curves,potentiodynamic polarization(PDP)curves and electrochemical impedance spectroscopy(EIS)tests characterized the oxygen vacancy defects and corrosion resistance of the coatings.The results demonstrated that laser-assisted irradiation not only induced plasma discharge on the anode surface,but also limited the plasma discharge size in the post-processing stage,which significantly increased the proportion of corrosion-resistant phase Mg_(2)SiO_(4)(the proportion of Mg_(2)SiO_(4)increased from 23.70%to 39.22%),thickness and density in the coating,and obviously reduced the oxygen vacancy defects and microcracks in the coating.As a result,the corrosion resistance of the Laser/PEO coating(9.29(±0.76)×10^(-7)A·cm^(-2))was further enhanced in comparation with the PEO coating(3.06(±0.19)×10^(-6) A·cm^(-2)).
基金supported by the UK EPSRC(grant EP/T024607/1,‘Coat IN’)provided by the Henry Royce Institute for Advanced Materials,funded through the UK EPSRC grants EP/R00661X/1,EP/S019367/1,EP/P025021/1 and EP/P025498/1support from the University of Manchester and Chinese Scholarship Council for his Ph D studies。
文摘Electrolyte selection for Plasma Electrolytic Oxidation(PEO)of magnesium is important as this determines composition,morphology and properties of resultant coatings that are urgently sought after for protection of Mg alloys from corrosion and wear in harsh environments.However,electrolyte design is often performed heuristically,which hampers the development and optimisation of new PEO processes.Here,we attempt to achieve a mechanistic understanding of electrochemical and microstructural aspects of anodic films evolution at the prebreakdown stages of PEO treatments of magnesium in aqueous alkaline solutions of NaAlO_(2),Na_(3)PO_(4),Na F and Na_(2)SiO_(3).Systematic studies have shown that magnesium self-passivation by MgO/Mg(OH)_(2)can be compromised by both chemical and mechanical instabilities developed due to side effects of anodic reactions.Stable initiation of PEO process requires maintaining surface passivity in a wide range of p H,which can be achieved only by combining self-depositing passivators with those binding dissolved magnesium into insoluble compounds.
文摘The corrosion resistance of magnesium alloys is a significant concern in industries seeking to use these materials for lightweight structures.Plasma electrolytic oxidation(PEO)is a process that forms a ceramic oxide film on Mg alloy surfaces,effectively enhancing their corrosion performance in the short term.In this regard,optimizing PEO process parameters is crucial for creating a stable oxide layer.An improved level of corrosion resistance is ensured by applying superhydrophobic coating(SHC)on top of the PEO layer to prevent moisture infiltration,creating air pockets on the surface.Various methods are employed to fabricate SHC on Mg alloys,including techniques like electrophoretic deposition(EPD),Hydrothermal(HT),dip,and spray coating.The synergistic combination of PEO and SHC coatings has demonstrated encouraging outcomes in enhancing the corrosion performance of Mg alloys.This study offers an extensive overview of recent progress in the preparation,characterization,and corrosion behavior of Mg alloys by employing PEO coatings and SHC treatment processes.
基金Funded by the National Natural Science Foundation of China(No.52271066)Basic Research and Innovation Project for Vehicle Power+1 种基金Key Project of"Two-Chain Integration"in Shaanxi Province(No.2023-LL-QY-33-3)Xi'an Key Laboratory of Corrosion Protection and Functional Coating Technology for Military and Civil Light Alloy and Key Project of Shaanxi Natural Science Foundation Research Program(No.2021JZ-54)。
文摘A novel type of microcapsule-encapsulated corrosion inhibitor was prepared in a water-based solution with a pH range of 7-8,and it was applied to the composite organic coating of magnesium alloy plasma electrolytic oxidation to enhance its corrosion resistance and self-healing properties.The morphology,chemical composition,structure,and functional properties of the composite coating were investigated by scanning electron microscopy(SEM),energy dispersive X-ray spectroscopy(EDS),Fourier transform infrared spectroscopy(FTIR),polarization curve,alternating current impedance,and salt immersion test.The experimental results showed that,after immersion in a 3.5 wt%NaCl solution for 12 h,the coating could effectively protect AZ91D from corrosion.When the coating was damaged,the exposed alloy surface would release metal ions in the corrosive environment and react with the corrosion inhibitor 8-hydroxyquinoline to form a Mg(8-HQ)_(2) chelate,exhibiting significant self-healing behavior.The study results demonstrate the broad application prospects of microcapsule technology in the coating field,providing new ideas for the development of efficient anti-corrosion coatings.
基金Projects(51071066,51671084)supported by the National Natural Science Foundation of ChinaProject(NCET-12-0172)supported by the Program for New Century Excellent Talents in University,Ministry of Education,China
文摘Plasma electrolytic oxidation of a cast A356 aluminum alloy was carried out in aluminate electrolytes to develop wear and corrosion resistant coatings. Different concentrations of 2, 16 and 24 g/L NaAlO2 solutions and a silicate electrolyte （for comparison） were employed for the investigation. Wear performance and corrosion resistance of the coatings were evaluated by WC （tungsten carbide） ball-on-flat dry sliding tests and electrochemical methods, respectively. The results show that the coating formed for a short duration of 480 s in 24 g/L NaAlO2 solution generated the best protection. The coating sustained 30 N load for sliding time of 1800 s, showing very low wear rate of -4.5×10^-7 mm3/（N· m）. A low corrosion current density of -8.81×10^-9 A/cm2 was also recorded. Despite low α-Al2O3 content of the coating, the compact and nearly single layer nature of the coating guaranteed the excellent performances.
文摘As an efficient surface modification approach,the plasma electrolytic oxidation(PEO)technique can boost the capability of wear protection in Mg and its alloys by applying a hard and thick ceramic coating.In this procedure,more efficient protection can be acquired via adding additives(in the form of particle,powder,sheet,etc.)into solutions and producing composite coatings.These additives result in more efficient protection against wear via getting stuck in the cracks and pores of coatings and rising the thickness,hardness,and diminishing the porosity size and content.The efficiency of each additive can be changed owing to its intrinsic properties like melting point,size,participation type(reactive,partly reactive,or inert)and potential of zeta.In this review,the effects of distinct additives in nano-and micro-scale size on wear behavior of PEO coatings on Mg and its alloys is going to be reviewed.
基金The authors are grateful to the Department of Science&Technology of Gansu Province(China)for the support of the Creative Research Group Fund Grant(1111RJDA011)the Open Fund(SKLAB02015006)from State Key Laboratory of Advanced Processing and Recycling of Non-ferrous Metals(China).
文摘Plasma electrolytic oxidation(PEO)coatings were prepared on AZ91D magnesium alloys in alkaline silicate-based electrolyte with and without additives.The mutual effects among additives including TiC particles,dispersant polyethylene glycol 6000(PEG6000)and anionic surfactant sodium dodecyl sulfate(SDS)were studied based on orthogonal experiment.The content and distribution of TiC deposited in the coatings were measured by EPMA and EDS.The thicknesses,phase compositions,microstructures and corrosion resistances of the codlings were cAarnined by using TT260 eddy current tuickncss gage,XRD,SEM and clcctrochcniical test,respectively.The results show that the experiment design of this study is the key to study the mutual effects among these additives.Each additive and their interactions all remarkably influence TiC content and corrosion resistance of the coatings.Smaller size TiC is much easier to migrate towards the anode,and the interaction between PEG6000 and SDS both effectively prevents its agglomeration and increases the number of its negative surface charges,which further increase the migration rate and the deposited uniformity of TiC and make TiC have more opportunity to deposit in the discharge channel.Thus,when smaller size TiC,PEG6000 and SDS are all added into the electrolyte,they could improve the anti-corrosion property of the coating to the largest extent attributed to higher TiC content and the densest microstructure of the coating.
基金The authors are grateful for the financial support from the National Natural Science Foundation of China(No.51671084).
文摘Plasma electrolytic oxidation(PEO)of cast A356 aluminum alloy was carried out in 32 g/L NaAlO_(2) with the addition of different concentrations of NaOH.The stability of the aluminate solution is greatly enhanced by increasing the concentration of NaOH.However,corresponding changes in the PEO behaviour occur due to the increment of NaOH concentration.Thicker precursor coatings are required for the PEO treatment in a more concentrated NaOH electrolyte.The results show that the optimal NaOH concentration is 5 g/L,which improves the stability of storage electrolyte to about 35 days,and leads to dense coatings with high wear performance(wear rate:4.1×10^(−7) mm^(3)·N^(−1)·m^(−1)).
基金supported by the National Natural Science Foundation of China (No. 51671084)the Postgraduate Scientific Research Innovation Project of Hunan Province, China (No. QL20210092)。
文摘Plasma electrolytic oxidation(PEO) of brass was carried out in aluminate electrolytes with the addition of NaH2PO4(S1) and Na2SiO3(S2), respectively, with the aim to investigate the effect of additives on the coating formation and corrosion resistance. For the PEO in S1 electrolyte, a mixed layer of AlPO4and Al2O3is formed at the initial stage, which leads to fast plasma discharges and formation of black coatings with the compositions of Al2O3,CuO, Cu2O and ZnO. However, in S2 electrolyte, plasma discharges are delayed and the coatings show a reddish color due to more Cu2O. Mott-Schottky tests show that the S1 coatings are p-type semiconductors;while the S2 coatings can be adjusted between n-type and p-type. Potentiodynamic polarization and electrochemical impedance spectroscopy(EIS) tests show that the PEO treatment can significantly improve the corrosion resistance of brass, with protection efficiency up to 91.50% and the largest charge transfer resistance of 59.95 kΩ·cm^(2) for the S1 coating.
基金financially supported by the Russian Science Foundation(Project No.14-33-00009)the Russian Federation Government(Federal Agency of Scientific Organizations)
文摘The formation of protective multifunctional coatings on magnesium alloy MA8 using plasma electrolyt- ic oxidation （PEO） in an electrolytic system containing nanosized particles of titanium nitride was investigated. Electrochemical and mechanical properties of the obtained layers were examined. It was established that microhardness of the coating with the nanoparticle concentration of 3 gl-1 increased twofold （4.2 ± 0.5 GPa）, while wear resistance decreased （4.97 × 10-6 mm3 N-1 m-1）, as compared to re- spective values for the PEO-coating formed in the electrolyte without nanoparticles （2.1 ± 0.3 GPa, 1.12 × 10.5 mm3 N-1 m-1）.
文摘In this study,ceramic coatings were deposited on 6061 Al alloy using a plasma electrolytic oxidation（PEO）technique,and the effect of concentrations of KOH and Na_2SiO_3 as electrolytes for PEO process was studied on microstructure,chemical composition,and electrochemical behavior of PEO coatings formed on the 6061 Al alloy.The results indicated that the increase in concentration of KOH led to rise in electrical conductivity of electrolyte.Consequently,the breakdown voltage reduced,which in turn improved the surface quality and the corrosion behavior.Moreover,the increase in concentration of Na_2SiO_3 resulted in the increase in incorporation of Si in the coating,which led to a higher corrosion potential in the concentration of 4 g L^（-1）.According to this investigation,the best protection behavior of coatings can be obtained when the KOH and Na_2SiO_3 concentrations in PEO electrolyte are equal to 4 g L^（-1）.
基金Funded by National Natural Science Foundation of China(No.51371039)Zhejiang Provincial Natural Science Foundation of China(No.LGG18E020004)+1 种基金Open Foundation of Zhejiang Provincial Top Key Discipline of Mechanical EngineeringScience and Technology Project of Zhejiang Province(No.2015C37037)
文摘Plasma electrolytic oxidation（PEO） coatings were prepared on AZ31 magnesium alloy using alkaline phosphate as base electrolyte system, and with the addition of sodium silicate（Na2SiO3）, sodium aluminate（NaAlO2） and potassium fluorozirconate（K2ZrF6） as additives. The microstructure, phase composition and element composition as well as surface profile of the PEO coatings were analyzed by means of scanning electron microscopy（SEM）, X-ray diffraction（XRD）, energy dispersive X-ray spectroscopy（EDS）, and threedimensional（3 D） optical profilometry. The corrosion and wear properties were evaluated by electrochemical potentiodynamic polarization in 3.5 wt% Na Cl solution and ball-on-disc wear tests, respectively. The results showed that the anions of the additives effectively participated in the coating formation influencing its microstructural features, chemical composition, corrosion resistance and tribological behaviour. It was observed that the sample treated by PEO in the electrolyte solution containing K2ZrF6 as an additive showed better corrosion and abrasive resistance.
基金financial support by the National Natural Science Foundation of China(No.52071067)Shenyang Young and Middle-aged Science and Technology Innovation Talent Support Program,China(No.RC231178)+1 种基金Natural Science Foundation of Liaoning Province,China(No.2022-YGJC-16)the Fundamental Research Funds for the Central Universities,China(No.N2302019).
文摘To enhance the long-term corrosion resistance of the plasma electrolytic oxidation(PEO)coating on the magnesium(Mg)alloy,an inorganic salt combined with corrosion inhibitors was used for posttreatment of the coating.In this study,the corrosion performance of PEO-coated AM50 Mg was significantly improved by loading sodium lauryl sulfonate(SDS)and sodium dodecyl benzene sulf-onate into Ba(NO_(3))_(2) post-sealing solutions.Scanning electron microscopy,X-ray photoelectron spectroscopy,X-ray diffraction,Fourier transform infrared spectrometer,and ultraviolet-visible analyses showed that the inhibitors enhanced the incorporation of BaO_(2) into PEO coatings.Electrochemical impedance showed that post-sealing in Ba(NO_(3))_(2)/SDS treatment enhanced corrosion resistance by three orders of magnitude.The total impedance value remained at 926Ω·cm^(2)after immersing in a 0.5wt%NaCl solution for 768 h.A salt spray test for 40 days did not show any obvious region of corrosion,proving excellent post-sealing by Ba(NO_(3))_(2)/SDS treatment.The corrosion resistance of the coating was enhanced through the synergistic effect of BaO2 pore sealing and SDS adsorption.
基金2024 Hongik University Innovation Support Program Fund。
文摘The favorable properties of Mg alloys,such as their lightweight and robust nature,are driving an increase in interest in their development for industrial and biomedical applications.These benefits aren’t enough to make them widely used;problems like poor corrosion resistance and no antibacterial qualities call attention to the need for improved coating methods.Because of its distinct characteristics and efficacy in surface modification,plasma electrolytic oxidation(PEO)has emerged as a preferred coating process.But protective coatings can only become better with time if we keep pushing them to new limits.PEO coatings on Mg alloys may be made more protective by using metal-organic frameworks(MOFs).Hybrid crystalline MOFs have been popular in inorganic and organic chemistry in recent decades.These complexes include organic ligands and metal ions or clusters.Large specific surface areas,customizable topologies and functionalities,ordered pore structures,and many reactive sites make these materials famous.Preventing corrosion using MOFs seems promising.This study analyzes MOF-led corrosion protection material advances and their efficacy in tackling corrosion challenges.A comprehensive review of numerous production techniques employed with MOFs for corrosion protection highlights their pros and cons.The report also discusses MOFs’potential corrosion-prevention functions and the challenges that must be overcome to make them viable.The corrosion-preventive ways of MOFs as inhibitors,nano-fillers,nano-containers,and surface-coating agents are also examined.As we conclude our detailed analysis,we provide a future-oriented vision of MOFs’undiscovered corrosion prevention potential.This exposition illustrates corrosion protection material advances employing cutting-edge MOF-based anticorrosion breakthroughs.It encourages creative ways to corrosion protection’s future.
基金supported by the 2022 Shenzhen sustainable supporting funds for colleges and universities(20220810143642004)Shenzhen Basic Research Project(JCYJ20200109144608205 and JCYJ20210324120001003)+5 种基金Peking University Shenzhen Graduate School Research Startup Fund of Introducing Talent(No.1270110273)Shenzhen postdoctoral research fund project after outbound(No.2129933651)Shenzhen-Hong Kong Research and Development Fund(No.SGDX20201103095406024)City University of Hong Kong Strategic Research Grants(SRG)(Nos.7005264 and 7005505)Guangdong-Hong Kong Technology Cooperation Funding Scheme(TCFS)(No.GHP/085/18SZ)IER Foundation(IERF2020001 and IERF2019002).
文摘In the present research,the NaF assisted plasma electrolytic oxidation(PEO)is designed to fabricate the high-content ZnO nanoparti-cles doped coating on AZ31B alloy.The microstructure,phase constituents and corrosion behavior of the PEO coatings are investigated systematically.The results reveal that the introduction of NaF promotes the formation of MgF2 nanophases in the passivation layer on Mg alloy,decreasing the breakdown voltage and discharge voltage.As a result,the continuous arcing caused by high discharge voltage is alleviated.With the increasing of NaF content,the Zn content in the PEO coating is enhanced and the pore size in the coating is decreased correspondingly.Due to the high-content ZnO doping,the PEO coating protected AZ31B alloy demonstrates the better corrosion resistance.Compared with the bare AZ31B alloy,the high-content ZnO doped PEO coated sample shows an increased corrosion potential from-1.465 V to-1.008 V,a decreased corrosion current density from 3.043×10^(-5) A·cm^(-2) to 3.960×10^(-8) A·cm^(-2) and an increased charge transfer resistance from 1.213×10^(2) ohm·cm^(2) to 2.598×10^(5) ohm·cm^(2).Besides,the high-content ZnO doped PEO coated sample also has the excellent corrosion resistance in salt solution,exhibiting no obvious corrosion after more than 2000 h neutral salt spraying and 28 days’immersion testing.The improved corrosion resistance can be ascribed to the relative uniform distribution of ZnO in PEO coating which can transform to Zn(OH)2 and form a continuous protective layer along the corrosion interface.
