This paper establishes a method for identifying and locating dynamic loads in time-varying systems.The proposed method linearizes time-varying parameters within small time units and uses the Wilson-θ inverse analysis...This paper establishes a method for identifying and locating dynamic loads in time-varying systems.The proposed method linearizes time-varying parameters within small time units and uses the Wilson-θ inverse analysis method to solve modal loads of each order at each time step.It then uses an exhaustive method to determine the load position.Finally,it calculates the time history of the load.Simulation examples demonstrate how the number of measuring points and step size affect load identi-fication accuracy,verifying that this algorithm achieves good identification accuracy for loads under resonance conditions.Additionally,it explores how noise affects load position and recognition accuracy,while providing a solution.Simulation examples and experimental results demonstrate that the proposed method can identify both the time history and position of loads simultaneously with high identification accuracy.展开更多
The structural dynamic response reconstruction technology can extract unmeasured information from limited measured data,significantly impacting vibration control,load identification,parameter identification,fault diag...The structural dynamic response reconstruction technology can extract unmeasured information from limited measured data,significantly impacting vibration control,load identification,parameter identification,fault diagnosis,and related fields.This paper proposes a dynamic response reconstruction method based on the Kalman filter,which simultaneously identifies external excitation and reconstructs dynamic responses at unmeasured positions.The weighted least squares method determines the load weighting matrix for excitation identification,while the minimum variance unbiased estimation determines the Kalman filter gain.The excitation prediction Kalman filter is constructed through time,excitation,and measurement updates.Subsequently,the response at the target point is reconstructed using the state vector,observation matrix,and excitation influence matrix obtained through the excitation prediction Kalman filter algorithm.An algorithm for reconstructing responses in continuous system using the excitation prediction Kalman filtering algorithm in modal space is derived.The proposed structural dynamic response reconstruction method evaluates the response reconstruction and the load identification performance under various load types and errors through simulation examples.Results demonstrate the accurate excitation identification under different load conditions and simultaneous reconstruction of target point responses,verifying the feasibility and reliability of the proposed method.展开更多
Under external disturbances,the shear mechanical responses and debonding failure mechanisms at anisotropic interfaces of anchoring system composed of multiphase media are inherently difficult to characterize due to th...Under external disturbances,the shear mechanical responses and debonding failure mechanisms at anisotropic interfaces of anchoring system composed of multiphase media are inherently difficult to characterize due to the concealment nature of interfacial interactions.This study establishes an equivalent shear model for a bolt-resin-rock anchoring system and conducts direct shear tests under dynamic normal load(DNL)boundary from both laboratory experiments and discrete element method(DEM)simulations.The research investigates the influence of normal dynamic load amplitude(An)and rock type on shear strength parameters,elucidating the evolutionary characteristics and underlying mechanisms of shear load and normal displacement fluctuations induced by cyclic normal loading,with maximum shear load decreasing by 36.81%to 46.94%as An increases from 10%to 70%when rock type varies from coal to limestone.Through analysis of strain field evolution,the critical impact of rock type on localization of shear failure surface is revealed,with systematic summarization of differentiated wear characteristics,failure modes,and key controlling factors associated with shear failure surface.Mesoscopic investigations enabled by DEM simulations uncover the nonuniform distribution of contact force chains within the material matrix and across the anisotropic interfaces under various DNL boundaries,clarify rock type dependent crack propagation pathways,and quantitatively assess the damage extent of shear failure surface,with the anisotropic interface damage factor increasing from 34.9%to 56.6%as An rises from 10%to 70%,and decreasing from 49.6%to 23.4%as rock type varies from coal to limestone.展开更多
The frequent or occasional impact loads pose serious threats to the service safety of conventional concrete structures in tunnel.In this paper,a novel three-dimensional mesoscopic model of steel fiber reinforced concr...The frequent or occasional impact loads pose serious threats to the service safety of conventional concrete structures in tunnel.In this paper,a novel three-dimensional mesoscopic model of steel fiber reinforced concrete(SFRC)is constructed by discrete element method.The model encompasses the concrete matrix,aggregate,interfacial transition zone and steel fibers,taking into account the random shape of the coarse aggregate and the stochastic distribution of steel fibers.It captures microscopic-level interactions among the coarse aggregate,steel fibers,and matrix.Subsequently,a comprehensive procedure is formulated to calibrate the microscopic parameters required by the model,and the reliability of the model is verified by comparing with the experimental results.Furthermore,a coupled finite difference method-discrete element method approach is used to construct the model of the split Hopkinson pressure bar.Compression tests are simulated on SFRC specimens with varying steel fiber contents under static and dynamic loading conditions.Finally,based on the advantages of DEM analysis at the mesoscopic level,this study analyzed mechanisms of enhancement and crack arrest in SFRC.It shed a light on the perspectives of interface failure process,microcrack propagation,contact force field evolution and energy analysis,offering valuable insights for related mining engineering applications.展开更多
In order to research the concrete archaized buildings with lintel-column joint,2 specimens were tested under dynamic experiment.The failure characteristics,skeleton curves,mechanical behavior such as the load-displace...In order to research the concrete archaized buildings with lintel-column joint,2 specimens were tested under dynamic experiment.The failure characteristics,skeleton curves,mechanical behavior such as the load-displacement hysteretic loops,load carrying capacity,degradation of strength and stiffness,ductility and energy dissipation of the joints were analyzed.The results indicate that comparies with the lintel-column joints,the loading capacity and energy dissipation of the concrete archaized buildings with dual lintel-column joints are higher,and the hysteretic loops is in plump-shape.However,the displacement ductility coefficient is less than that of lintel-column joints.Both of them of the regularity of rigidity degeneration are basically the same.Generally,the joints have the good energy dissipation capacity.And the concrete archaized buildings with lintel-column joints exhibit excellent seismic behavior.展开更多
The damage properties of two types of rocks under dynamic loading are studied. The shock induced experiments are done using planar impact technique on the one? stage light gas gun, and the ultrasonic tests on the da...The damage properties of two types of rocks under dynamic loading are studied. The shock induced experiments are done using planar impact technique on the one? stage light gas gun, and the ultrasonic tests on the damaged rocks have been made by use of the ultrasonic pulse? transmission method. The shock induced damage of rock is related to the shock speed and the attenuation coefficient of sonic wave, and the latter reflects the damage degree in rock fairly well. The attenuation coefficient α can be used as main damage parameter for constructing damage model of rock under dynamic loading.展开更多
In order to investigate the mechanical response of reflective cracking in asphalt concrete pavement under dynamic vehicle loading, a finite element model is established in ABAQUS. The viscoelastic behavior is describe...In order to investigate the mechanical response of reflective cracking in asphalt concrete pavement under dynamic vehicle loading, a finite element model is established in ABAQUS. The viscoelastic behavior is described by a prony series which is calculated through nonlinear fitting to the creep test data obtained in the laboratory. Based on the viscoelastic theory, the time-temperature equivalence principle, fracture mechanics and the dynamic finite element method, both the Jintegral and the mix-mode stress intensity factor are utilized as fracture evaluation parameters, and a half-sine dynamic loading is used to simulate the vehicle loading. Finally, the mechanical response of the pavement reflective cracking is analyzed under different vehicle speeds, different environmental conditions and various damping factors. The results indicate that increasing either the vehicle speed or the structure damping factor decreases the maximum values of fracture parameters, while the structure temperature has little effect on the fracture parameters. Due to the fact that the vehicle speed can be enhanced by improving the road traffic conditions, and the pavement damping factor can become greater by modifying the components of materials, the development of reflective cracking can be delayed and the asphalt pavement service life can be effectively extended through both of these ways.展开更多
It is not uncommon that backfill material used in underground mining being exposed to repetitive dynamic stresses induced by blasting operations or rockburst events. Understanding the strength and fracture evolution o...It is not uncommon that backfill material used in underground mining being exposed to repetitive dynamic stresses induced by blasting operations or rockburst events. Understanding the strength and fracture evolution of backfilled stopes is critical to maintain the long-term stope stability and ensure safe mining activities. This paper aims to study the damage evolution of the backfill material and its host rock behaviour under three-dimensional(3D) dynamic loading. Using a true-triaxial testing machine, multiple samples of backfill material enclosed by country rock were fabricated and tested under various dynamic loadings with different true-triaxial confining stress conditions. In addition, the nuclear magnetic resonance(NMR) measurement was conducted on the samples before and after exerting static and dynamic loading to obtain their porosity distribution changes. The experiment results suggested that with the increase of the dynamic loading, the porosity of the backfill sample goes through a two-stage process,which shows a slightly linear decrease and then followed by an exponential increase. The research findings can help understand the damage mechanism and fracture development of backfilled stopes and its host rock in deep underground mines, which are constantly subject to the combination of 3D static confining stress and dynamic loading.展开更多
The stability control of surrounding rock for large or super-large section chamber is a difficult technical problem in deep mining condition.Based on the in-site geological conditions of Longgu coal mine,this paper us...The stability control of surrounding rock for large or super-large section chamber is a difficult technical problem in deep mining condition.Based on the in-site geological conditions of Longgu coal mine,this paper used the dynamic module of FLAC3D to study the response characteristics of deep super-large section chamber under dynamic and static combined loading condition.Results showed that under the static loading condition,the maximum vertical stress,deformation and failure range are large,where the stress concentration coefficient is 1.64.The maximum roof-to-floor and two-sides deformations are 54.6 mm and 53.1 mm,respectively.Then,under the dynamic and static combined loading condition:(1)The influence of dynamic load frequency on the two-sides is more obvious;(2)The dynamic load amplitude has the greatest influence on the stress concentration degree,and the plastic failure tends to develop to the deeper;(3)With the dynamic load source distance increase,the response of surrounding rock is gradually attenuated.On this basis,empirical equations for each dynamic load conditions were obtained by using regression analysis method,and all correlation coefficients are greater than 0.99.This research provided reference for the supporting design of deep super-large section chamber under same or similar conditions.展开更多
A dynamic marine propeller simulation system was developed, which is utilized for meeting the experimental requirement of theory research and engineering design of marine electric propulsion system. By applying an act...A dynamic marine propeller simulation system was developed, which is utilized for meeting the experimental requirement of theory research and engineering design of marine electric propulsion system. By applying an actual ship parameter and its accurate propeller J＇ -KT＇ and J＇ - Kp＇ curve data, functional experiments based on the simulation system were carried out. The experiment results showed that the system can correctly emulate the propeller characteristics, produce the dynamic and steady performances of the propeller under different navigation modes, and present actual load torque for electric propulsion motor.展开更多
Most current researches working on improving stiffness focus on the application of control theories.But controller in closed-loop hydraulic control system takes effect only after the controlled position is deviated,so...Most current researches working on improving stiffness focus on the application of control theories.But controller in closed-loop hydraulic control system takes effect only after the controlled position is deviated,so the control action is lagged.Thus dynamic performance against force disturbance and dynamic load stiffness can’t be improved evidently by advanced control algorithms.In this paper,the elementary principle of maintaining piston position unchanged under sudden external force load change by charging additional oil is analyzed.On this basis,the conception of raising dynamic stiffness of electro hydraulic position servo system by flow feedforward compensation is put forward.And a scheme using double servo valves to realize flow feedforward compensation is presented,in which another fast response servo valve is added to the regular electro hydraulic servo system and specially utilized to compensate the compressed oil volume caused by load impact in time.The two valves are arranged in parallel to control the cylinder jointly.Furthermore,the model of flow compensation is derived,by which the product of the amplitude and width of the valve’s pulse command signal can be calculated.And determination rules of the amplitude and width of pulse signal are concluded by analysis and simulations.Using the proposed scheme,simulations and experiments at different positions with different force changes are conducted.The simulation and experimental results show that the system dynamic performance against load force impact is largely improved with decreased maximal dynamic position deviation and shortened settling time.That is,system dynamic load stiffness is evidently raised.This paper proposes a new method which can effectively improve the dynamic stiffness of electro-hydraulic servo systems.展开更多
Rocks are likely to undergo spalling failure under dynamic loading.The fracture development and rock failure behaviours were investigated during dynamic tensile loading.Tests were conducted with a split-Hopkinson pres...Rocks are likely to undergo spalling failure under dynamic loading.The fracture development and rock failure behaviours were investigated during dynamic tensile loading.Tests were conducted with a split-Hopkinson pressure bar(SHPB)in four different impact loading conditions.Thin sections near failure surfaces were also made to evaluate the growth patterns of fractures observed by polarizing microscope.Scanning electron microscopy(SEM)was used to observe mineral grains on failure surfaces and to evaluate their response to loading and failure.The results indicate that the number of spalling cracks increases with increase in peak impact loads and that quartz sustains abundant intergranular fracturing.Cleavage planes and their direction relative to loading play a vital role in rock strength and fracturing.Separation along cleavage planes perpendicular to loading without the movement of micaceous minerals parallel to loading appears to be unique to the rock spalling process.展开更多
Centrifuge experiments are carried out to investigate the responses of suction bucket foundations under horizontal dynamic loading. The effects of loading amplitude, the size of the bucket and the structural weight on...Centrifuge experiments are carried out to investigate the responses of suction bucket foundations under horizontal dynamic loading. The effects of loading amplitude, the size of the bucket and the structural weight on the dynamic responses are investigated. It is shown that, when the loading amplitude is over a critical value, the sand at the upper part around the bucket softens or even liquefies. The liquefaction index （excess pore pressure divided by initial effective stress. In this paper, the developmental degree of excess pore pressure is described by liquefaction index） decreases from the upper part to the lower part of the sand foundation in the vertical direction and decreases from near to far away from the bucket＇s side wall in the horizontal direction, large settlements of the bucket and the sand around the bucket are induced by the horizontal dynamic loading. The dynamic responses of the bucket of a smaller height （when the diameter is the same） are heavier. A cyclic crack some distance near the bucket occurs in the sand.展开更多
Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers e...Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers embedded in a concrete matrix usually play a strong bridging effect to enhance the bonding force between fiber and the matrix,and directly contribute to the improvement of the post-cracking behavior and residual strength of SFRC.To gain a better understanding of the action behavior of steel fibers in matrix and further capture the failure mechanism of SFRC under dynamic loads,the mesoscopic modeling approach that assumes SFRC to be composed of different mesoscale phases(i.e.,steel fibers,coarse aggregates,mortar matrix,and interfacial transition zone(ITZ))has been widely employed to simulate the dynamic responses of SFRC material and structural members.This paper presents a comprehensive review of the state-of-the-art mesoscopic models and simulations for SFRC under dynamic loading.Generation approaches for the SFRC mesoscale model in the simulation works,including steel fiber,coarse aggregate,and the ITZ between them,are reviewed and compared systematically.The material models for different phases and the interaction relationship between fiber and concrete matrix are summarized comprehensively.Additionally,some example applications for SFRC under dynamic loads(i.e.,compression,tension,and contact blast)simulated using the general mesoscale models are given.Finally,some critical analysis on the current shortcomings of the mesoscale modeling of SFRC is highlighted,which is of great significance for the future investigation and development of SFRC.展开更多
A new type of a loading and measuring system was developed for testing failure and deformation of rock core samples with an industrial CT （ICT） scanner.The loading and measuring system consisted of a loading system ...A new type of a loading and measuring system was developed for testing failure and deformation of rock core samples with an industrial CT （ICT） scanner.The loading and measuring system consisted of a loading system and a computer control system.The maximum servo-controlled force was 2 tonnes.The new system was a high-stiffness system with a small size.During ICT tests,rock core samples could be easily loaded in the axial direction.So the initiation,propagation,and coalescence of cracks in core samples were observed on ICT images.展开更多
In order to describe the relationship between dynamic process and sludge removing load in active sludge system, a new method for designing the volume of aeration tanks was put forward based on the Michaelis and Menten...In order to describe the relationship between dynamic process and sludge removing load in active sludge system, a new method for designing the volume of aeration tanks was put forward based on the Michaelis and Menten equation. the influence of sludge returning was considered in the design. The result shows that the parameter of sludge reflux ratio plays a very important role in the design of active sludge system. In some given conditions,there exists an optimum reflux ratio which can make the volume of aeration tank be the minimum.展开更多
Split Hopkinson Pressure Bar(SHPB) test was simulated to investigate the distribution of the first principal stress and damage zone of specimen subjected to dynamic compressive load. Numerical models of plate-type spe...Split Hopkinson Pressure Bar(SHPB) test was simulated to investigate the distribution of the first principal stress and damage zone of specimen subjected to dynamic compressive load. Numerical models of plate-type specimen containing cracks with inclined angles of 0°,45° and 90° were also established to investigate the crack propagation and damage evolution under dynamic loading. The results show that the simulation results are in accordance with the failure patterns of specimens in experimental test. The interactions between stress wave and crack with different inclined angles are different; damage usually appears around the crack tips firstly; and then more damage zones develop away from the foregoing damage zone after a period of energy accumulation; eventually,the damage zones run through the specimen in the direction of applied loading and split the specimen into pieces.展开更多
By means of the improved split Hopkionson pressure bar(SHPB) with axial pre-pressure and confined pressure, two series of experiments on sandstone are carried out to research the failure mode of rock during the course...By means of the improved split Hopkionson pressure bar(SHPB) with axial pre-pressure and confined pressure, two series of experiments on sandstone are carried out to research the failure mode of rock during the course of exploitation of resources in deep. One is under the conditions that the con-fining pressure is fixed and the axial pressure is changeable. The other is under the conditions that the confining pressure becomes and the axial pressure is fixed. It is found that samples break up evenly after impacting when axial static pressures are low, there is great disparity in size of fragments when axial static pressures are high, and the main bodies of samples after the tests under the combination of dy-namic and static loads frequently show the type of V or X. The samples are more close-grained at the elastic stage and impacts make many cracks be generated and developed, as makes samples more crackable. At the initial phase of damage stage, the static pressures make some cracks in the samples which are undeveloped and the impacts′ role is similar to that at the elastic stage. At the metaphase or anaphase of damage stage, these cracks in the samples develop adequately and the impacts mainly accelerate samples′ failure. The main bodies of samples show the type of V or X after impacting due to the confining pressures′ restraining samples′ lateral formation at the elastic stage or the initial phase of damage stage, the main bodies of samples have almost formed at the stage loading static pressures and the results after impacting usually are similar to those under the axial pressures tests.展开更多
Dynamic properties of rocks are important in a variety of rock mechanics and rock engineering problems. Due to the transient nature of the loading, dynamic tests of rock materials are very different from and much more...Dynamic properties of rocks are important in a variety of rock mechanics and rock engineering problems. Due to the transient nature of the loading, dynamic tests of rock materials are very different from and much more challenging than their static counterparts. Dynamic tests are usually conducted using the split Hopkinson bar or Kolsl^j bar systems, which include both split Hopkinson pressure bar （SHPB） and split Hopkinson tension bar （SHTB） systems. Significant progress has been made on the quantification of various rock dynamic properties, owing to the advances in the experimental techniques of SHPB system. This review aims to fully describe and critically assess the detailed procedures and principles of tech- niques for dynamic rock tests using split Hopkinson bars. The history and principles of SHPB are outlined, followed by the key loading techniques that are useful for dynamic rock tests with SHPB （i.e. pulse shaping, momentum-trap and multi-axial loading techniques）. Various measurement techniques for rock tests in SHPB （i.e. X-ray micro computed tomography （CT）, laser gap gauge （LGG）, digital image corre- lation （DIC）, Moir~ method, caustics method, photoelastic coating method, dynamic infrared thermog- raphy） are then discussed. As the main objective of the review, various dynamic measurement techniques for rocks using SHPB are described, including dynamic rock strength measurements （i.e. dynamic compression, tension, bending and shear tests）, dynamic fracture measurements （i.e. dynamic imitation and propagation fracture toughness, dynamic fracture energy and fracture velocity）, and dy- namic techniques for studying the influences of temperature and pore water.展开更多
The mathematical model of dynamic loads was developed based on an analysis of the polished rod load of beam pumps, and the variation of the dynamic loads and the computation of the minimum and maximum limits during a ...The mathematical model of dynamic loads was developed based on an analysis of the polished rod load of beam pumps, and the variation of the dynamic loads and the computation of the minimum and maximum limits during a complete pumping cycle were given out by solving the model.Field examples verify that it is necessary to take into account the inertial and vibration loads while calculating polished rod loads.During the prophase of the pumping production, the dynamic to polished rod load ratio is relatively large.Then the ratio decreases rapidly and becomes small after entering stable production.Moreover, the total deformation of rod and tubing in CBM wells is much smaller than that in oil fields, and the deformation caused by the dynamic loads is also relatively small.The result of this work is the calculation of the dynamic loads.The application of this calculation for the sucker rod pumping system in CBM wells can give the desired accuracy of polished rod load and the dynamometer cards, which provides a reasonable basis for the design and selection of beam pumps.展开更多
基金supported by the Priority Academic Program Development of Jiangsu Higher Education Institutions.
文摘This paper establishes a method for identifying and locating dynamic loads in time-varying systems.The proposed method linearizes time-varying parameters within small time units and uses the Wilson-θ inverse analysis method to solve modal loads of each order at each time step.It then uses an exhaustive method to determine the load position.Finally,it calculates the time history of the load.Simulation examples demonstrate how the number of measuring points and step size affect load identi-fication accuracy,verifying that this algorithm achieves good identification accuracy for loads under resonance conditions.Additionally,it explores how noise affects load position and recognition accuracy,while providing a solution.Simulation examples and experimental results demonstrate that the proposed method can identify both the time history and position of loads simultaneously with high identification accuracy.
基金supported by the National Natural Science Foundation of China(Nos.12372066,U23B6009,52171261)the Aeronautical Science Fund(No.20240013052002)the Qing Lan Project。
文摘The structural dynamic response reconstruction technology can extract unmeasured information from limited measured data,significantly impacting vibration control,load identification,parameter identification,fault diagnosis,and related fields.This paper proposes a dynamic response reconstruction method based on the Kalman filter,which simultaneously identifies external excitation and reconstructs dynamic responses at unmeasured positions.The weighted least squares method determines the load weighting matrix for excitation identification,while the minimum variance unbiased estimation determines the Kalman filter gain.The excitation prediction Kalman filter is constructed through time,excitation,and measurement updates.Subsequently,the response at the target point is reconstructed using the state vector,observation matrix,and excitation influence matrix obtained through the excitation prediction Kalman filter algorithm.An algorithm for reconstructing responses in continuous system using the excitation prediction Kalman filtering algorithm in modal space is derived.The proposed structural dynamic response reconstruction method evaluates the response reconstruction and the load identification performance under various load types and errors through simulation examples.Results demonstrate the accurate excitation identification under different load conditions and simultaneous reconstruction of target point responses,verifying the feasibility and reliability of the proposed method.
基金support from the National Natural Science Foundation of China(Nos.51504247,52174092,51904290,and 52074259)the Natural Science Foundation of Jiangsu Province,China(No.BK20220157)+1 种基金the Fundamental Research Funds for the Central Universities,China(No.2022YCPY0202)the China University of Mining and Technology(CUMT)Open Sharing Fund for Large-scale Instruments and Equipment(No.DYGX-2025-47)is gratefully acknowledged.
文摘Under external disturbances,the shear mechanical responses and debonding failure mechanisms at anisotropic interfaces of anchoring system composed of multiphase media are inherently difficult to characterize due to the concealment nature of interfacial interactions.This study establishes an equivalent shear model for a bolt-resin-rock anchoring system and conducts direct shear tests under dynamic normal load(DNL)boundary from both laboratory experiments and discrete element method(DEM)simulations.The research investigates the influence of normal dynamic load amplitude(An)and rock type on shear strength parameters,elucidating the evolutionary characteristics and underlying mechanisms of shear load and normal displacement fluctuations induced by cyclic normal loading,with maximum shear load decreasing by 36.81%to 46.94%as An increases from 10%to 70%when rock type varies from coal to limestone.Through analysis of strain field evolution,the critical impact of rock type on localization of shear failure surface is revealed,with systematic summarization of differentiated wear characteristics,failure modes,and key controlling factors associated with shear failure surface.Mesoscopic investigations enabled by DEM simulations uncover the nonuniform distribution of contact force chains within the material matrix and across the anisotropic interfaces under various DNL boundaries,clarify rock type dependent crack propagation pathways,and quantitatively assess the damage extent of shear failure surface,with the anisotropic interface damage factor increasing from 34.9%to 56.6%as An rises from 10%to 70%,and decreasing from 49.6%to 23.4%as rock type varies from coal to limestone.
基金financial support by the National Natural Science Foundation of China(52174101&52408310)Guangdong Basic and Applied Basic Research Foundation(2023A1515011634&2024A1515012528)Guangdong Provincial Department of Science and Technology(2021ZT09G087)for the research.
文摘The frequent or occasional impact loads pose serious threats to the service safety of conventional concrete structures in tunnel.In this paper,a novel three-dimensional mesoscopic model of steel fiber reinforced concrete(SFRC)is constructed by discrete element method.The model encompasses the concrete matrix,aggregate,interfacial transition zone and steel fibers,taking into account the random shape of the coarse aggregate and the stochastic distribution of steel fibers.It captures microscopic-level interactions among the coarse aggregate,steel fibers,and matrix.Subsequently,a comprehensive procedure is formulated to calibrate the microscopic parameters required by the model,and the reliability of the model is verified by comparing with the experimental results.Furthermore,a coupled finite difference method-discrete element method approach is used to construct the model of the split Hopkinson pressure bar.Compression tests are simulated on SFRC specimens with varying steel fiber contents under static and dynamic loading conditions.Finally,based on the advantages of DEM analysis at the mesoscopic level,this study analyzed mechanisms of enhancement and crack arrest in SFRC.It shed a light on the perspectives of interface failure process,microcrack propagation,contact force field evolution and energy analysis,offering valuable insights for related mining engineering applications.
基金supported by Crosswise Tasks of Enterprise Entrusted(JG-ZH-A-202411-003)High-level Talents Program of Hainan Basic and Applied Basic Research Program of China(520RC543)。
文摘In order to research the concrete archaized buildings with lintel-column joint,2 specimens were tested under dynamic experiment.The failure characteristics,skeleton curves,mechanical behavior such as the load-displacement hysteretic loops,load carrying capacity,degradation of strength and stiffness,ductility and energy dissipation of the joints were analyzed.The results indicate that comparies with the lintel-column joints,the loading capacity and energy dissipation of the concrete archaized buildings with dual lintel-column joints are higher,and the hysteretic loops is in plump-shape.However,the displacement ductility coefficient is less than that of lintel-column joints.Both of them of the regularity of rigidity degeneration are basically the same.Generally,the joints have the good energy dissipation capacity.And the concrete archaized buildings with lintel-column joints exhibit excellent seismic behavior.
文摘The damage properties of two types of rocks under dynamic loading are studied. The shock induced experiments are done using planar impact technique on the one? stage light gas gun, and the ultrasonic tests on the damaged rocks have been made by use of the ultrasonic pulse? transmission method. The shock induced damage of rock is related to the shock speed and the attenuation coefficient of sonic wave, and the latter reflects the damage degree in rock fairly well. The attenuation coefficient α can be used as main damage parameter for constructing damage model of rock under dynamic loading.
文摘In order to investigate the mechanical response of reflective cracking in asphalt concrete pavement under dynamic vehicle loading, a finite element model is established in ABAQUS. The viscoelastic behavior is described by a prony series which is calculated through nonlinear fitting to the creep test data obtained in the laboratory. Based on the viscoelastic theory, the time-temperature equivalence principle, fracture mechanics and the dynamic finite element method, both the Jintegral and the mix-mode stress intensity factor are utilized as fracture evaluation parameters, and a half-sine dynamic loading is used to simulate the vehicle loading. Finally, the mechanical response of the pavement reflective cracking is analyzed under different vehicle speeds, different environmental conditions and various damping factors. The results indicate that increasing either the vehicle speed or the structure damping factor decreases the maximum values of fracture parameters, while the structure temperature has little effect on the fracture parameters. Due to the fact that the vehicle speed can be enhanced by improving the road traffic conditions, and the pavement damping factor can become greater by modifying the components of materials, the development of reflective cracking can be delayed and the asphalt pavement service life can be effectively extended through both of these ways.
基金National Natural Science Foundation of China (Grant No.51804079)Fujian Natural Science Foundation (Grant No.2019J05039)
文摘It is not uncommon that backfill material used in underground mining being exposed to repetitive dynamic stresses induced by blasting operations or rockburst events. Understanding the strength and fracture evolution of backfilled stopes is critical to maintain the long-term stope stability and ensure safe mining activities. This paper aims to study the damage evolution of the backfill material and its host rock behaviour under three-dimensional(3D) dynamic loading. Using a true-triaxial testing machine, multiple samples of backfill material enclosed by country rock were fabricated and tested under various dynamic loadings with different true-triaxial confining stress conditions. In addition, the nuclear magnetic resonance(NMR) measurement was conducted on the samples before and after exerting static and dynamic loading to obtain their porosity distribution changes. The experiment results suggested that with the increase of the dynamic loading, the porosity of the backfill sample goes through a two-stage process,which shows a slightly linear decrease and then followed by an exponential increase. The research findings can help understand the damage mechanism and fracture development of backfilled stopes and its host rock in deep underground mines, which are constantly subject to the combination of 3D static confining stress and dynamic loading.
基金Project(2018YFC0604703)supported by the National Key R&D Program of ChinaProjects(51804181,51874190)supported by the National Natural Science Foundation of China+3 种基金Project(ZR2018QEE002)supported by the Shandong Province Natural Science Fund,ChinaProject(ZR2018ZA0603)supported by the Major Program of Shandong Province Natural Science Foundation,ChinaProject(2019GSF116003)supported by the Key R&D Project of Shandong Province,ChinaProject(SDKDYC190234)supported by the Shandong University of Science and Technology,Graduate Student Technology Innovation Project,China。
文摘The stability control of surrounding rock for large or super-large section chamber is a difficult technical problem in deep mining condition.Based on the in-site geological conditions of Longgu coal mine,this paper used the dynamic module of FLAC3D to study the response characteristics of deep super-large section chamber under dynamic and static combined loading condition.Results showed that under the static loading condition,the maximum vertical stress,deformation and failure range are large,where the stress concentration coefficient is 1.64.The maximum roof-to-floor and two-sides deformations are 54.6 mm and 53.1 mm,respectively.Then,under the dynamic and static combined loading condition:(1)The influence of dynamic load frequency on the two-sides is more obvious;(2)The dynamic load amplitude has the greatest influence on the stress concentration degree,and the plastic failure tends to develop to the deeper;(3)With the dynamic load source distance increase,the response of surrounding rock is gradually attenuated.On this basis,empirical equations for each dynamic load conditions were obtained by using regression analysis method,and all correlation coefficients are greater than 0.99.This research provided reference for the supporting design of deep super-large section chamber under same or similar conditions.
基金supported by the Fund of Shanghai Committee of Science and Technology(Grant No.11170501700)the International Cooperation and Exchange Projects of the Ministry of Science and Technology(Grant No.2012DFG71850)
文摘A dynamic marine propeller simulation system was developed, which is utilized for meeting the experimental requirement of theory research and engineering design of marine electric propulsion system. By applying an actual ship parameter and its accurate propeller J＇ -KT＇ and J＇ - Kp＇ curve data, functional experiments based on the simulation system were carried out. The experiment results showed that the system can correctly emulate the propeller characteristics, produce the dynamic and steady performances of the propeller under different navigation modes, and present actual load torque for electric propulsion motor.
基金supported by National Natural Science Foundation of China(Grant No.51075291)Shanxi Scholarship Council of China(Grant No.2012-076)
文摘Most current researches working on improving stiffness focus on the application of control theories.But controller in closed-loop hydraulic control system takes effect only after the controlled position is deviated,so the control action is lagged.Thus dynamic performance against force disturbance and dynamic load stiffness can’t be improved evidently by advanced control algorithms.In this paper,the elementary principle of maintaining piston position unchanged under sudden external force load change by charging additional oil is analyzed.On this basis,the conception of raising dynamic stiffness of electro hydraulic position servo system by flow feedforward compensation is put forward.And a scheme using double servo valves to realize flow feedforward compensation is presented,in which another fast response servo valve is added to the regular electro hydraulic servo system and specially utilized to compensate the compressed oil volume caused by load impact in time.The two valves are arranged in parallel to control the cylinder jointly.Furthermore,the model of flow compensation is derived,by which the product of the amplitude and width of the valve’s pulse command signal can be calculated.And determination rules of the amplitude and width of pulse signal are concluded by analysis and simulations.Using the proposed scheme,simulations and experiments at different positions with different force changes are conducted.The simulation and experimental results show that the system dynamic performance against load force impact is largely improved with decreased maximal dynamic position deviation and shortened settling time.That is,system dynamic load stiffness is evidently raised.This paper proposes a new method which can effectively improve the dynamic stiffness of electro-hydraulic servo systems.
基金the financial supports from the National Natural Science Foundation of China(Nos.51904335,51904333,11772357,51927808)。
文摘Rocks are likely to undergo spalling failure under dynamic loading.The fracture development and rock failure behaviours were investigated during dynamic tensile loading.Tests were conducted with a split-Hopkinson pressure bar(SHPB)in four different impact loading conditions.Thin sections near failure surfaces were also made to evaluate the growth patterns of fractures observed by polarizing microscope.Scanning electron microscopy(SEM)was used to observe mineral grains on failure surfaces and to evaluate their response to loading and failure.The results indicate that the number of spalling cracks increases with increase in peak impact loads and that quartz sustains abundant intergranular fracturing.Cleavage planes and their direction relative to loading play a vital role in rock strength and fracturing.Separation along cleavage planes perpendicular to loading without the movement of micaceous minerals parallel to loading appears to be unique to the rock spalling process.
基金This study programis supported by the fund of the Chinese Ocean Oil Co.and the Chinese Academy of Sciences ,KJCX2-SW-L03-01 (40025103) andthe National Natural Science Foundation of China (Grant No.10202024)
文摘Centrifuge experiments are carried out to investigate the responses of suction bucket foundations under horizontal dynamic loading. The effects of loading amplitude, the size of the bucket and the structural weight on the dynamic responses are investigated. It is shown that, when the loading amplitude is over a critical value, the sand at the upper part around the bucket softens or even liquefies. The liquefaction index （excess pore pressure divided by initial effective stress. In this paper, the developmental degree of excess pore pressure is described by liquefaction index） decreases from the upper part to the lower part of the sand foundation in the vertical direction and decreases from near to far away from the bucket＇s side wall in the horizontal direction, large settlements of the bucket and the sand around the bucket are induced by the horizontal dynamic loading. The dynamic responses of the bucket of a smaller height （when the diameter is the same） are heavier. A cyclic crack some distance near the bucket occurs in the sand.
基金the financial support from the National Natural Science Foundation of China(52178190 and 52078250)the Science and Technology on Near-Surface Detection Laboratory(6142414200505)+1 种基金the Interdisciplinary Innovation Fundation for Graduates,Nanjing University of Aeronautics and Astronautics(KXKCXJJ202005)The support provided by the China Scholarship Council(202006830096)during a visit of Zhangyu Wu to University College London。
文摘Steel fiber reinforced concrete(SFRC)has drawn extensive attention in recent years for its superior mechanical response to dynamic and impact loadings.Based on the existing test results,the highstrength steel fibers embedded in a concrete matrix usually play a strong bridging effect to enhance the bonding force between fiber and the matrix,and directly contribute to the improvement of the post-cracking behavior and residual strength of SFRC.To gain a better understanding of the action behavior of steel fibers in matrix and further capture the failure mechanism of SFRC under dynamic loads,the mesoscopic modeling approach that assumes SFRC to be composed of different mesoscale phases(i.e.,steel fibers,coarse aggregates,mortar matrix,and interfacial transition zone(ITZ))has been widely employed to simulate the dynamic responses of SFRC material and structural members.This paper presents a comprehensive review of the state-of-the-art mesoscopic models and simulations for SFRC under dynamic loading.Generation approaches for the SFRC mesoscale model in the simulation works,including steel fiber,coarse aggregate,and the ITZ between them,are reviewed and compared systematically.The material models for different phases and the interaction relationship between fiber and concrete matrix are summarized comprehensively.Additionally,some example applications for SFRC under dynamic loads(i.e.,compression,tension,and contact blast)simulated using the general mesoscale models are given.Finally,some critical analysis on the current shortcomings of the mesoscale modeling of SFRC is highlighted,which is of great significance for the future investigation and development of SFRC.
基金financially supported by the National Natural Science Foundation of China (Grant No. 50905186,No. 51174213)the Major State Basic Research Development Program Fund (Grant No. 2010CB226804)the Project-sponsored by SRF for ROCS,the Ministry of Education and Fundamental Research Funds for the Central Universities and Research Program in State Key Laboratory of Coal Resources and Safe Mining of China University of Mining and Technology
文摘A new type of a loading and measuring system was developed for testing failure and deformation of rock core samples with an industrial CT （ICT） scanner.The loading and measuring system consisted of a loading system and a computer control system.The maximum servo-controlled force was 2 tonnes.The new system was a high-stiffness system with a small size.During ICT tests,rock core samples could be easily loaded in the axial direction.So the initiation,propagation,and coalescence of cracks in core samples were observed on ICT images.
文摘In order to describe the relationship between dynamic process and sludge removing load in active sludge system, a new method for designing the volume of aeration tanks was put forward based on the Michaelis and Menten equation. the influence of sludge returning was considered in the design. The result shows that the parameter of sludge reflux ratio plays a very important role in the design of active sludge system. In some given conditions,there exists an optimum reflux ratio which can make the volume of aeration tank be the minimum.
基金Projects(50534030, 50674107, 50490274) supported by the National Natural Science Foundation of ChinaProject(06JJ3028) supported by the Provincial Natural Science Foundation of Hunan, China
文摘Split Hopkinson Pressure Bar(SHPB) test was simulated to investigate the distribution of the first principal stress and damage zone of specimen subjected to dynamic compressive load. Numerical models of plate-type specimen containing cracks with inclined angles of 0°,45° and 90° were also established to investigate the crack propagation and damage evolution under dynamic loading. The results show that the simulation results are in accordance with the failure patterns of specimens in experimental test. The interactions between stress wave and crack with different inclined angles are different; damage usually appears around the crack tips firstly; and then more damage zones develop away from the foregoing damage zone after a period of energy accumulation; eventually,the damage zones run through the specimen in the direction of applied loading and split the specimen into pieces.
基金Supported by National Natural Science Foundation of China(No.10472134 and No.50490274)
文摘By means of the improved split Hopkionson pressure bar(SHPB) with axial pre-pressure and confined pressure, two series of experiments on sandstone are carried out to research the failure mode of rock during the course of exploitation of resources in deep. One is under the conditions that the con-fining pressure is fixed and the axial pressure is changeable. The other is under the conditions that the confining pressure becomes and the axial pressure is fixed. It is found that samples break up evenly after impacting when axial static pressures are low, there is great disparity in size of fragments when axial static pressures are high, and the main bodies of samples after the tests under the combination of dy-namic and static loads frequently show the type of V or X. The samples are more close-grained at the elastic stage and impacts make many cracks be generated and developed, as makes samples more crackable. At the initial phase of damage stage, the static pressures make some cracks in the samples which are undeveloped and the impacts′ role is similar to that at the elastic stage. At the metaphase or anaphase of damage stage, these cracks in the samples develop adequately and the impacts mainly accelerate samples′ failure. The main bodies of samples show the type of V or X after impacting due to the confining pressures′ restraining samples′ lateral formation at the elastic stage or the initial phase of damage stage, the main bodies of samples have almost formed at the stage loading static pressures and the results after impacting usually are similar to those under the axial pressures tests.
文摘Dynamic properties of rocks are important in a variety of rock mechanics and rock engineering problems. Due to the transient nature of the loading, dynamic tests of rock materials are very different from and much more challenging than their static counterparts. Dynamic tests are usually conducted using the split Hopkinson bar or Kolsl^j bar systems, which include both split Hopkinson pressure bar （SHPB） and split Hopkinson tension bar （SHTB） systems. Significant progress has been made on the quantification of various rock dynamic properties, owing to the advances in the experimental techniques of SHPB system. This review aims to fully describe and critically assess the detailed procedures and principles of tech- niques for dynamic rock tests using split Hopkinson bars. The history and principles of SHPB are outlined, followed by the key loading techniques that are useful for dynamic rock tests with SHPB （i.e. pulse shaping, momentum-trap and multi-axial loading techniques）. Various measurement techniques for rock tests in SHPB （i.e. X-ray micro computed tomography （CT）, laser gap gauge （LGG）, digital image corre- lation （DIC）, Moir~ method, caustics method, photoelastic coating method, dynamic infrared thermog- raphy） are then discussed. As the main objective of the review, various dynamic measurement techniques for rocks using SHPB are described, including dynamic rock strength measurements （i.e. dynamic compression, tension, bending and shear tests）, dynamic fracture measurements （i.e. dynamic imitation and propagation fracture toughness, dynamic fracture energy and fracture velocity）, and dy- namic techniques for studying the influences of temperature and pore water.
基金Supported by the National Science and Technology Special Project of China(2008ZX05038-004)Shandong Province Science and Technology Development Project(2009GG10007008)
文摘The mathematical model of dynamic loads was developed based on an analysis of the polished rod load of beam pumps, and the variation of the dynamic loads and the computation of the minimum and maximum limits during a complete pumping cycle were given out by solving the model.Field examples verify that it is necessary to take into account the inertial and vibration loads while calculating polished rod loads.During the prophase of the pumping production, the dynamic to polished rod load ratio is relatively large.Then the ratio decreases rapidly and becomes small after entering stable production.Moreover, the total deformation of rod and tubing in CBM wells is much smaller than that in oil fields, and the deformation caused by the dynamic loads is also relatively small.The result of this work is the calculation of the dynamic loads.The application of this calculation for the sucker rod pumping system in CBM wells can give the desired accuracy of polished rod load and the dynamometer cards, which provides a reasonable basis for the design and selection of beam pumps.
