The double-sided lapping process is extensively employed in the manufacturing of wafers,optical windows,and seal rings due to its high efficiency and ability to achieve precise flatness.However,limited research has ex...The double-sided lapping process is extensively employed in the manufacturing of wafers,optical windows,and seal rings due to its high efficiency and ability to achieve precise flatness.However,limited research has explored the thickness uniformity among different workpieces after double-sided lapping,and the underlying mechanism remains unclear.To address the demand for higher precision,this paper first analyzed the relative kinematic model between the workpiece and the lapping plate to clarify the causes of thickness variations among workpieces after double-sided lapping.Subsequently,a finite element method(FEM)model was developed to account for the pressure distribution on the workpiece surfaces at the initial stage of the process.The results indicate that the number of workpieces influences the final thickness variation.Then,various sets of thin copper plates with different thicknesses were lapped,and the findings revealed that five copper plates processed simultaneously exhibited more uniform thickness compared to the three plates.The experimental results align well with the theoretical analysis.Ultimately,a thickness variation of less than 6μm was achieved on five copper plates measuringΦ100×2.9 mm.This study presents a comprehensive analysis of the mechanisms influencing thickness uniformity in the double-sided lapping process and provides practical guidelines for optimizing the process to achieve stringent precision standards in industrial applications.展开更多
Bio-magnesium(Mg)alloys exhibit excellent biocompatibility and biodegradability,making them highly promising for implant applications.However,their limited strength-ductility balance remains a critical challenge restr...Bio-magnesium(Mg)alloys exhibit excellent biocompatibility and biodegradability,making them highly promising for implant applications.However,their limited strength-ductility balance remains a critical challenge restricting widespread use.In this study,ultra-fine-grained and homogeneous Mg alloys were fabricated using double-sided friction stir processing(DS-FSP)with liquid CO_(2) rapid cooling,leading to a significant enhancement in the strength-ductility synergy of the stirred zone.The results demonstrate that DS-FSP samples exhibit simultaneous improvements in ultimate tensile strength(UTS)and elongation,reaching 334.1±15 MPa and 28.2±7.3%,respectively.Compared to the non-uniform fine-grained microstructure obtained through single-sided friction stir processing,DS-FSP generates a uniform ultra-fine-grained structure,fundamentally altering the fracture behavior and mechanisms of Mg alloys.The DS-FSP samples exhibit irregular fracture patterns due to variations in basal slip system activation among different grains.In contrast,single-sided friction stir processing samples,characterized by a fine-grained yet heterogeneous microstructure,display flat shear fractures dominated by high-density dislocation initiation induced by twin formation,with fracture propagation dictated by the non-uniform texture.By achieving an ultra-fine grain size and homogeneous texture,DS-FSP effectively modifies the fracture mechanisms,thereby enhancing the strength-ductility balance of bio-magnesium alloys.展开更多
Currently,conventional single-sided friction stir welding is primarily suitable for joining thin plate aluminum alloys,and its application to thick plates is still challenging in terms of welding efficiency and joint ...Currently,conventional single-sided friction stir welding is primarily suitable for joining thin plate aluminum alloys,and its application to thick plates is still challenging in terms of welding efficiency and joint mechanical properties.Simultaneous double-sided friction stir welding(SDS-FSW)is a high-efficiency joining technique specifically developed for welding thick plates.However,there is little research on the influence of SDS-FSW process parameters on the joint mechanical properties.In this study,a 12 mm thick AA6061-T6 aluminum alloy and dual robot welding equipment are used to conduct SDS-FSW experiments exploring the influence of rotational speedωand welding speed v on the mechanical properties and microstructure.The results show that when the welding parameters areω=800 r/min and v=60–80 mm/min,smooth and defect-free thick plate aluminum alloy SDS-FSW joints can be obtained,and the macroscopic morphology of the joints is distributed in a“dumbbell”shape.The grain size in the weld nugget zone increases with increasing welding heat input.The microhardness distribution in the joint displays a“W”shape,and the hardness value of the weld nugget zone can reach 67%to 86%of that of the base metal(BM).The junction between the thermo-mechanically affected zone and the heat affected zone is the weakest region of the joint,with the lowest hardness being approximately 51%of that of the BM.When the welding parameters areω=800 r/min and v=140 mm/min,the SDS-FSW joint has the highest tensile strength,reaching 78.43%of the BM strength and exhibiting ductile fracture characteristics.This research indicates that acceptable weld strength in thick aluminum alloys can be achieved via the SDS-FSW joining mechanism,highlighting its significant potential for industrial applications.展开更多
Land surface temperature(LST)is the key variable in land-atmosphere interaction,having an important impact on weather and climate forecasting.However,achieving consistent analysis of LST and the atmosphere in assimila...Land surface temperature(LST)is the key variable in land-atmosphere interaction,having an important impact on weather and climate forecasting.However,achieving consistent analysis of LST and the atmosphere in assimilation is quite challenging.This is because there is limited knowledge about the cross-component background error covariance(BEC)between LST and atmospheric state variables.This study aims to clarify whether there is a relationship between the error of LST and atmospheric variables,and whether this relationship varies spatially and temporally.To this end,the BEC coupled with atmospheric variables and LST was constructed(LST-BEC),and its characteristics were analyzed based on the 2023 mei-yu season.The general characteristics of LST-BEC show that the LST is mainly correlated with the atmospheric temperature and the correlation decreases gradually with a rise in atmospheric height,and the error standard deviation of the LST is noticeably larger than that of the low-level atmospheric temperature.The spatiotemporal characteristics of LST-BEC on the heavy-rain day and light-rain day show that the error correlation and error standard deviation of LST and low-level atmospheric temperature and humidity are closely related to the weather background,and also have obvious diurnal variations.These results provide valuable information for strongly coupled land-atmosphere assimilation.展开更多
The proposed hybrid optimization algorithm integrates particle swarm optimizatio(PSO)with Ant Colony Optimization(ACO)to improve a number of pitfalls within PSO methods traditionally considered and/or applied to indus...The proposed hybrid optimization algorithm integrates particle swarm optimizatio(PSO)with Ant Colony Optimization(ACO)to improve a number of pitfalls within PSO methods traditionally considered and/or applied to industrial robots.Particle Swarm Optimization may frequently suffer from local optima and inaccuracies in identifying the geometric parameters,which are necessary for applications requiring high-accuracy performances.The proposed approach integrates pheromone-based learning of ACO with the D-H method of developing an error model;hence,the global search effectiveness together with the convergence accuracy is further improved.Comparison studies of the hybrid PSO-ACO algorithm show higher precision and effectiveness in the optimization of geometric error parameters compared to the traditional methods.This is a remarkable reduction of localization errors,thus yielding accuracy and reliability in industrial robotic systems,as the results show.This approach improves performance in those applications that demand high geometric calibration by reducing the geometric error.The paper provides an overview of input for developing robotics and automation,giving importance to precision in industrial engineering.The proposed hybrid methodology is a good way to enhance the working accuracy and effectiveness of industrial robots and shall enable their wide application to complex tasks that require a high degree of accuracy.展开更多
In this paper,a wideband true time delay line for X-band is designed to overcome the beam dispersion problem in a high-resolution spaceborne synthetic aperture radar phased array antenna system.The delay line loads th...In this paper,a wideband true time delay line for X-band is designed to overcome the beam dispersion problem in a high-resolution spaceborne synthetic aperture radar phased array antenna system.The delay line loads the electromagnetic bandgap structure on the upper surface of the substrate integrated waveguide.This is equivalent to including an additional inductance-capacitance for energy storage,which realizes the slow-wave effect.A microstrip line-SIW tapered transition structure is introduced to achieve a low loss and a large bandwidth.In the frequency band between 8-12 GHz,the measured results show that the delay multiplier of the delay line reaches 4 times,i.e.,delay line’s delay time is 4 times larger than 50Ωmicrostrip line with same length.Furthermore,the delay fluctuation,i.e.,the difference between the maximum and minimum delay as a percentage of the standard delay is only 2.5%,the insertion loss is less than-2.5 dB,and the return loss is less than-15 dB.Compared with the existing delay lines,the proposed delay line has the advantages of high delay efficiency,low delay error,wide bandwidth and low loss,which has good practical value and application prospects.展开更多
In this paper,we develop a multi-scalar auxiliary variables(MSAV)scheme for the Cahn-Hilliard Magnetohydrodynamics system by introducing two scalar auxiliary variables(SAV).This scheme is linear,fully decoupled and un...In this paper,we develop a multi-scalar auxiliary variables(MSAV)scheme for the Cahn-Hilliard Magnetohydrodynamics system by introducing two scalar auxiliary variables(SAV).This scheme is linear,fully decoupled and unconditionally stable in energy.Subsequently,we provide a detailed implementation procedure for full decoupling.Thus,at each time step,only a series of linear differential equations with constant coefficients need to be solved.To validate the effectiveness of our approach,we conduct an error analysis for this first-order scheme.Finally,some numerical experiments are provided to verify the energy dissipation of the system and the convergence of the proposed approach.展开更多
Capacitive voltage transformers (CVTs) are essential in high-voltage systems. An accurate error assessment is crucial for precise energy metering. However, tracking real-time quantitative changes in capacitive voltage...Capacitive voltage transformers (CVTs) are essential in high-voltage systems. An accurate error assessment is crucial for precise energy metering. However, tracking real-time quantitative changes in capacitive voltage transformer errors, particularly minor variations in multi-channel setups, remains challenging. This paper proposes a method for online error tracking of multi-channel capacitive voltage transformers using a Co-Prediction Matrix. The approach leverages the strong correlation between in-phase channels, particularly the invariance of the signal proportions among them. By establishing a co-prediction matrix based on these proportional relationships, The influence of voltage changes on the primary measurements is mitigated. Analyzing the relationships between the co-prediction matrices over time allows for inferring true measurement errors. Experimental validation with real-world data confirms the effectiveness of the method, demonstrating its capability to continuously track capacitive voltage transformer measurement errors online with precision over extended durations.展开更多
Contour error is the deviation between the actual displacement and reference trajectory,which is directly related to the machining accuracy.Contour error compensation poses substantial challenges because of the time-v...Contour error is the deviation between the actual displacement and reference trajectory,which is directly related to the machining accuracy.Contour error compensation poses substantial challenges because of the time-varying,nonlinear,and strongly coupled characteristics of parallel machining modules.In addition,the time delay in the system reduces the timeliness of the feedback data,thereby making online contour error calculations and compensation particularly difficult.To solve this problem,the generation mechanism of the time delay of the feedback data and contour error is revealed,and a systematic method for the identification of the time-delay parameter based on Beckhoff’s tracking error calculation mechanism is proposed.The temporal alignment between the position commands and feedback data enables the online calculation of the contour error.On this basis,the tracking error of the drive axes(an important factor resulting in end-effector contour errors)is used for the contour error calculation.Considering the ambiguous parameter-setting logic of the servo drive,the servo parameter is calculated in reverse using the steady-state error to obtain the tracking error model of the drive axes.Furthermore,combined with the system time-delay model,an online correction method for the tracking error estimation model is established.To achieve an accurate mapping of the drive-axis tracking error and end-effector contour error,a bounded iterative search method for the nearest contour point and online calculation model for the contour error are respectively established.Finally,an online compensation controller for contour error is designed.Its effectiveness is verified by a machining experiment on a frame workpiece.The machining results show that the contour error reduces from 68μm to 45μm,and the finish machining accuracy increases by 34%.This study provides a feasible method for online compensation of contour error in a system with time delay.展开更多
In this paper, we proposed an output voltage stabilization of a DC-DC Zeta converter using hybrid control. We modeled the Zeta converter under continuous conduction mode operation. We derived a switching control law t...In this paper, we proposed an output voltage stabilization of a DC-DC Zeta converter using hybrid control. We modeled the Zeta converter under continuous conduction mode operation. We derived a switching control law that brings the output voltage to the desired level. Due to infinite switching occurring at the desired level, we enhanced the switching control law by allowing a sizeable output voltage ripple. We derived mathematical models that allow one to choose the desired switching frequency. In practice, the existence of the non-ideal properties of the Zeta converter results in steady-state output voltage error. By analyzing the power loss in the zeta converter, we proposed an improved switching control law that eliminates the steady-state output voltage error. The effectiveness of the proposed method is illustrated with simulation results.展开更多
Accuracy allocation is crucial in the accuracy design of machining tools.Current accuracy allocation methods primarily focus on positional deviation,with little consideration for tool direction deviation.To address th...Accuracy allocation is crucial in the accuracy design of machining tools.Current accuracy allocation methods primarily focus on positional deviation,with little consideration for tool direction deviation.To address this issue,we propose a geometric error cost sensitivity-based accuracy allocation method for five-axis machine tools.A geometric error model consisting of 4l error components is constructed based on homogeneous transformation matrices.Volumetric points with positional and tool direction deviations are randomly sampled to evaluate the accuracy of the machine tool.The sensitivity of each error component at these sampling points is analyzed using the Sobol method.To balance the needs of geometric precision and manufacturing cost,a geometric error cost sensitivity function is developed to estimate the required cost.By allocating error components affecting tool direction deviation first and the remaining components second,this allocation scheme ensures that both deviations meet the requirements.We also perform numerical simulation of a BC-type(B-axis and C-axis type)five-axis machine tool to validate the method.The results show that the new allocation scheme reduces the total geometric error cost by 27.8%compared to a uniform allocation scheme,and yields the same positional and tool direction machining accuracies.展开更多
Most of the existing direction of arrival(DOA)estimation algorithms are applied under the assumption that the array manifold is ideal.In practical engineering applications,the existence of non-ideal conditions such as...Most of the existing direction of arrival(DOA)estimation algorithms are applied under the assumption that the array manifold is ideal.In practical engineering applications,the existence of non-ideal conditions such as mutual coupling between array elements,array amplitude and phase errors,and array element position errors leads to defects in the array manifold,which makes the performance of the algorithm decline rapidly or even fail.In order to solve the problem of DOA estimation in the presence of amplitude and phase errors and array element position errors,this paper introduces the first-order Taylor expansion equivalent model of the received signal under the uniform linear array from the Bayesian point of view.In the solution,the amplitude and phase error parameters and the array element position error parameters are regarded as random variables obeying the Gaussian distribution.At the same time,the expectation-maximization algorithm is used to update the probability distribution parameters,and then the two error parameters are solved alternately to obtain more accurate DOA estimation results.Finally,the effectiveness of the proposed algorithm is verified by simulation and experiment.展开更多
The fragility and stochastic behavior of quantum sources make it crucial to witness the topology of quantum networks.Most previous theoretical methods are based on perfect assumptions of quantum measurements.In this w...The fragility and stochastic behavior of quantum sources make it crucial to witness the topology of quantum networks.Most previous theoretical methods are based on perfect assumptions of quantum measurements.In this work,we propose a method to witness network topology under imperfect assumptions of quantum measurements.We show that the discrimination between star and triangle networks depends on the specific error tolerances of local measurements.This extends recent results for witnessing the triangle network[Phys.Rev.Lett.132240801(2024)].展开更多
Based on a hybrid system consisting of a quantum dot coupled with a double-sided micropillar cavity, we investigate the implementation of an error-detected photonic quantum routing controlled by the other photon. The ...Based on a hybrid system consisting of a quantum dot coupled with a double-sided micropillar cavity, we investigate the implementation of an error-detected photonic quantum routing controlled by the other photon. The computational errors from unexpected experimental imperfections are heralded by single photon detections, resulting in a unit fidelity for the present scheme, so that this scheme is intrinsically robust. We discuss the performance of the scheme with currently achievable experimental parameters. Our results show that the present scheme is efficient. Furthermore, our scheme could provide a promising building block for quantum networks and distributed quantum information processing in the future.展开更多
Null compensation interferometry is the primary testing method for the manufacture of ultra-high-precision aspheric mirrors.The crosstalk fringes generated by stray light in interferometry can affect accuracy and pote...Null compensation interferometry is the primary testing method for the manufacture of ultra-high-precision aspheric mirrors.The crosstalk fringes generated by stray light in interferometry can affect accuracy and potentially prevent the testing from proceeding normally.Position errors include the decenter error,tilt error,and distance error.During the testing process,position errors will impact the testing accuracy and the crosstalk fringes generated by stray light.To determine the specific impact of position errors,we use the concept of Hindle shell testing of a convex aspheric mirror,and propose the simulation method of crosstalk fringes in null compensation interferometry.We also propose evaluation indices of crosstalk fringes in interferometry and simulate the influence of position errors on the crosstalk fringes.This work aims to help improve the design of compensation interferometry schemes,enhance the feasibility of the design,reduce engineering risks,and improve efficiency.展开更多
Quantum computing has the potential to solve complex problems that are inefficiently handled by classical computation.However,the high sensitivity of qubits to environmental interference and the high error rates in cu...Quantum computing has the potential to solve complex problems that are inefficiently handled by classical computation.However,the high sensitivity of qubits to environmental interference and the high error rates in current quantum devices exceed the error correction thresholds required for effective algorithm execution.Therefore,quantum error correction technology is crucial to achieving reliable quantum computing.In this work,we study a topological surface code with a two-dimensional lattice structure that protects quantum information by introducing redundancy across multiple qubits and using syndrome qubits to detect and correct errors.However,errors can occur not only in data qubits but also in syndrome qubits,and different types of errors may generate the same syndromes,complicating the decoding task and creating a need for more efficient decoding methods.To address this challenge,we used a transformer decoder based on an attention mechanism.By mapping the surface code lattice,the decoder performs a self-attention process on all input syndromes,thereby obtaining a global receptive field.The performance of the decoder was evaluated under a phenomenological error model.Numerical results demonstrate that the decoder achieved a decoding accuracy of 93.8%.Additionally,we obtained decoding thresholds of 5%and 6.05%at maximum code distances of 7 and 9,respectively.These results indicate that the decoder used demonstrates a certain capability in correcting noise errors in surface codes.展开更多
This study aimed to identify and compensate for the geometric errors of the double swiveling axes in a five-axis computer numerical control(CNC)machining center.Hence,a three-dimensional coordinate calculation algorit...This study aimed to identify and compensate for the geometric errors of the double swiveling axes in a five-axis computer numerical control(CNC)machining center.Hence,a three-dimensional coordinate calculation algorithm for a measured point with additional rotational rigid body motion constraints is proposed.The motion constraints of the rotational rigid body were analyzed,and a mathematical model of the measured point algorithm in the swiveling axes was established.The Levenberg-Marquard method was used to solve the nonlinear superstatically determined equations.The spatial coordinate error was used to separate the spatial deviation of the measured point.An identification model of the position-independent and position-dependent geometric errors was established.The three-dimensional coordinate-solving algorithm of the measured point in the swiveling axis and geometric error identification method based on the Monte Carlo method were analyzed numerically.Geometric error measurement and cutting experiments were performed on a VMC25100U five-axis machining center,which integrated two swiveling axes.Geometric errors of the A-and B-axes were identified and measured experimentally.The angular positioning errors before and after compensation were measured using a laser interferometer,which verified the effectiveness of the proposed algorithm.A cutting experiment of a round table part was performed.The shape and position accuracy of the processed part before and after compensation were detected using a coordinate measuring machine.It verified that the geometric error of the swiveling axis was effectively compensated by the algorithm proposed herein.展开更多
In bridge engineering,monitoring pier offsets is crucial for ensuring both structural safety and construction quality.The total station measurement method using a reflector is widely employed,offering significant adva...In bridge engineering,monitoring pier offsets is crucial for ensuring both structural safety and construction quality.The total station measurement method using a reflector is widely employed,offering significant advantages in specific scenarios.During measurements,errors are influenced by various factors.Initially,misalignment causes the lateral relative error to increase before decreasing,while longitudinal relative errors fluctuate due to instrument characteristics and operational factors.Lateral movements have a more pronounced impact on these errors.Investigating the positioning layout of pier offsets holds substantial importance as it enables precise displacement monitoring,prevents accidents,aids in maintenance planning,provides valuable references for design and construction,and enhances the pier’s resistance to deflection.Controlling and correcting subsequent errors is essential to ensure the overall safety of the bridge structure.展开更多
Quantum error correction is essential for realizing fault-tolerant quantum computing,where both the efficiency and accuracy of the decoding algorithms play critical roles.In this work,we introduce the implementation o...Quantum error correction is essential for realizing fault-tolerant quantum computing,where both the efficiency and accuracy of the decoding algorithms play critical roles.In this work,we introduce the implementation of the PLANAR algorithm,a software framework designed for fast and exact decoding of quantum codes with a planar structure.The algorithm first converts the optimal decoding of quantum codes into a partition function computation problem of an Ising spin glass model.Then it utilizes the exact Kac–Ward formula to solve it.In this way,PLANAR offers the exact maximum likelihood decoding in polynomial complexity for quantum codes with a planar structure,including the surface code with independent code-capacity noise and the quantum repetition code with circuit-level noise.Unlike traditional minimumweight decoders such as minimum-weight perfect matching(MWPM),PLANAR achieves theoretically optimal performance while maintaining polynomial-time efficiency.In addition,to demonstrate its capabilities,we exemplify the implementation using the rotated surface code,a commonly used quantum error correction code with a planar structure,and show that PLANAR achieves a threshold of approximately p_(uc)≈0.109 under the depolarizing error model,with a time complexity scaling of O(N^(0.69)),where N is the number of spins in the Ising model.展开更多
AIM:To compare refractive error and angle of deviation in patients with basic esotropia and basic exotropia.METHODS:A retrospective review was conducted on the medical records of patients with basic-type strabismus.De...AIM:To compare refractive error and angle of deviation in patients with basic esotropia and basic exotropia.METHODS:A retrospective review was conducted on the medical records of patients with basic-type strabismus.Demographic data,refractive error,best-corrected distance visual acuity(BCVA),and the horizontal and vertical angle of deviation between basic esotropia and exotropia patients were compared.RESULTS:Among the 7129 patients(mean age 22.98±14.81y)evaluated,44.7%(3185 cases,54.9%male)exhibited basic-type esotropia,while 55.3%(3944 cases,53.9%male)presented with basic-type exotropia.Basic esotropia cases exhibited more hyperopic spherical equivalent measurements in both eyes(right:0.53±3.07 vs left:0.56±2.98 D)than those with basic exotropia(right eye:-0.33±2.84 vs left eye:-0.24±2.68 D,P<0.001 for both eyes).Patients with basic esotropia had significantly greater horizontal deviation angles(near:36.08±18.87 PD and far:35.56±18.75 PD)compared to those with basic exotropia(near:33.75±16.11 PD and far:33.26±15.90 PD,P<0.001).Conversely,patients with basic exotropia had slightly higher vertical deviation angles(near:1.67±5.80 PD and far:1.72±5.89 PD)compared to those with basic esotropia(near:1.12±4.57 PD and far:1.12±4.58 PD,P<0.001).Patients with basic esotropia underwent surgical intervention at younger ages compared to basic exotropia individuals(19.68±15.99 vs 25.66±13.20,P<0.001).CONCLUSION:Basic esotropia patients present more hyperopic refractive errors,better visual acuity,larger horizontal yet smaller vertical ocular misalignments,and tend to undergo strabismus surgery at younger ages relative to basic exotropia cases.展开更多
基金Supported by the Liaoning Provincial Natural Science Foundation(Grant No.2023-MSBA-008)Unveiling and Commanding Program of Liaoning Province(Grant No.2022JH1/10800080)the Fundamental Research Funds for the Central Universities(Grant No.DUT24MS008).
文摘The double-sided lapping process is extensively employed in the manufacturing of wafers,optical windows,and seal rings due to its high efficiency and ability to achieve precise flatness.However,limited research has explored the thickness uniformity among different workpieces after double-sided lapping,and the underlying mechanism remains unclear.To address the demand for higher precision,this paper first analyzed the relative kinematic model between the workpiece and the lapping plate to clarify the causes of thickness variations among workpieces after double-sided lapping.Subsequently,a finite element method(FEM)model was developed to account for the pressure distribution on the workpiece surfaces at the initial stage of the process.The results indicate that the number of workpieces influences the final thickness variation.Then,various sets of thin copper plates with different thicknesses were lapped,and the findings revealed that five copper plates processed simultaneously exhibited more uniform thickness compared to the three plates.The experimental results align well with the theoretical analysis.Ultimately,a thickness variation of less than 6μm was achieved on five copper plates measuringΦ100×2.9 mm.This study presents a comprehensive analysis of the mechanisms influencing thickness uniformity in the double-sided lapping process and provides practical guidelines for optimizing the process to achieve stringent precision standards in industrial applications.
基金financial support from the National Key Research and Development Program of China(2021YFC2400703)Zhengzhou City Major Special Project for Collaborative InnovationChina Scholarship Council。
文摘Bio-magnesium(Mg)alloys exhibit excellent biocompatibility and biodegradability,making them highly promising for implant applications.However,their limited strength-ductility balance remains a critical challenge restricting widespread use.In this study,ultra-fine-grained and homogeneous Mg alloys were fabricated using double-sided friction stir processing(DS-FSP)with liquid CO_(2) rapid cooling,leading to a significant enhancement in the strength-ductility synergy of the stirred zone.The results demonstrate that DS-FSP samples exhibit simultaneous improvements in ultimate tensile strength(UTS)and elongation,reaching 334.1±15 MPa and 28.2±7.3%,respectively.Compared to the non-uniform fine-grained microstructure obtained through single-sided friction stir processing,DS-FSP generates a uniform ultra-fine-grained structure,fundamentally altering the fracture behavior and mechanisms of Mg alloys.The DS-FSP samples exhibit irregular fracture patterns due to variations in basal slip system activation among different grains.In contrast,single-sided friction stir processing samples,characterized by a fine-grained yet heterogeneous microstructure,display flat shear fractures dominated by high-density dislocation initiation induced by twin formation,with fracture propagation dictated by the non-uniform texture.By achieving an ultra-fine grain size and homogeneous texture,DS-FSP effectively modifies the fracture mechanisms,thereby enhancing the strength-ductility balance of bio-magnesium alloys.
基金Supported by National Key R&D program of China(Grant No.2019YFA0709004)。
文摘Currently,conventional single-sided friction stir welding is primarily suitable for joining thin plate aluminum alloys,and its application to thick plates is still challenging in terms of welding efficiency and joint mechanical properties.Simultaneous double-sided friction stir welding(SDS-FSW)is a high-efficiency joining technique specifically developed for welding thick plates.However,there is little research on the influence of SDS-FSW process parameters on the joint mechanical properties.In this study,a 12 mm thick AA6061-T6 aluminum alloy and dual robot welding equipment are used to conduct SDS-FSW experiments exploring the influence of rotational speedωand welding speed v on the mechanical properties and microstructure.The results show that when the welding parameters areω=800 r/min and v=60–80 mm/min,smooth and defect-free thick plate aluminum alloy SDS-FSW joints can be obtained,and the macroscopic morphology of the joints is distributed in a“dumbbell”shape.The grain size in the weld nugget zone increases with increasing welding heat input.The microhardness distribution in the joint displays a“W”shape,and the hardness value of the weld nugget zone can reach 67%to 86%of that of the base metal(BM).The junction between the thermo-mechanically affected zone and the heat affected zone is the weakest region of the joint,with the lowest hardness being approximately 51%of that of the BM.When the welding parameters areω=800 r/min and v=140 mm/min,the SDS-FSW joint has the highest tensile strength,reaching 78.43%of the BM strength and exhibiting ductile fracture characteristics.This research indicates that acceptable weld strength in thick aluminum alloys can be achieved via the SDS-FSW joining mechanism,highlighting its significant potential for industrial applications.
基金sponsored by the National Natural Science Foundation of China[grant number U2442218]。
文摘Land surface temperature(LST)is the key variable in land-atmosphere interaction,having an important impact on weather and climate forecasting.However,achieving consistent analysis of LST and the atmosphere in assimilation is quite challenging.This is because there is limited knowledge about the cross-component background error covariance(BEC)between LST and atmospheric state variables.This study aims to clarify whether there is a relationship between the error of LST and atmospheric variables,and whether this relationship varies spatially and temporally.To this end,the BEC coupled with atmospheric variables and LST was constructed(LST-BEC),and its characteristics were analyzed based on the 2023 mei-yu season.The general characteristics of LST-BEC show that the LST is mainly correlated with the atmospheric temperature and the correlation decreases gradually with a rise in atmospheric height,and the error standard deviation of the LST is noticeably larger than that of the low-level atmospheric temperature.The spatiotemporal characteristics of LST-BEC on the heavy-rain day and light-rain day show that the error correlation and error standard deviation of LST and low-level atmospheric temperature and humidity are closely related to the weather background,and also have obvious diurnal variations.These results provide valuable information for strongly coupled land-atmosphere assimilation.
文摘The proposed hybrid optimization algorithm integrates particle swarm optimizatio(PSO)with Ant Colony Optimization(ACO)to improve a number of pitfalls within PSO methods traditionally considered and/or applied to industrial robots.Particle Swarm Optimization may frequently suffer from local optima and inaccuracies in identifying the geometric parameters,which are necessary for applications requiring high-accuracy performances.The proposed approach integrates pheromone-based learning of ACO with the D-H method of developing an error model;hence,the global search effectiveness together with the convergence accuracy is further improved.Comparison studies of the hybrid PSO-ACO algorithm show higher precision and effectiveness in the optimization of geometric error parameters compared to the traditional methods.This is a remarkable reduction of localization errors,thus yielding accuracy and reliability in industrial robotic systems,as the results show.This approach improves performance in those applications that demand high geometric calibration by reducing the geometric error.The paper provides an overview of input for developing robotics and automation,giving importance to precision in industrial engineering.The proposed hybrid methodology is a good way to enhance the working accuracy and effectiveness of industrial robots and shall enable their wide application to complex tasks that require a high degree of accuracy.
基金Supported by the National Natural Science Foundation of China(61971401)。
文摘In this paper,a wideband true time delay line for X-band is designed to overcome the beam dispersion problem in a high-resolution spaceborne synthetic aperture radar phased array antenna system.The delay line loads the electromagnetic bandgap structure on the upper surface of the substrate integrated waveguide.This is equivalent to including an additional inductance-capacitance for energy storage,which realizes the slow-wave effect.A microstrip line-SIW tapered transition structure is introduced to achieve a low loss and a large bandwidth.In the frequency band between 8-12 GHz,the measured results show that the delay multiplier of the delay line reaches 4 times,i.e.,delay line’s delay time is 4 times larger than 50Ωmicrostrip line with same length.Furthermore,the delay fluctuation,i.e.,the difference between the maximum and minimum delay as a percentage of the standard delay is only 2.5%,the insertion loss is less than-2.5 dB,and the return loss is less than-15 dB.Compared with the existing delay lines,the proposed delay line has the advantages of high delay efficiency,low delay error,wide bandwidth and low loss,which has good practical value and application prospects.
基金Research Project Supported by Shanxi Scholarship Council of China(2021-029)International Cooperation Base and Platform Project of Shanxi Province(202104041101019)Basic Research Plan of Shanxi Province(202203021211129)。
文摘In this paper,we develop a multi-scalar auxiliary variables(MSAV)scheme for the Cahn-Hilliard Magnetohydrodynamics system by introducing two scalar auxiliary variables(SAV).This scheme is linear,fully decoupled and unconditionally stable in energy.Subsequently,we provide a detailed implementation procedure for full decoupling.Thus,at each time step,only a series of linear differential equations with constant coefficients need to be solved.To validate the effectiveness of our approach,we conduct an error analysis for this first-order scheme.Finally,some numerical experiments are provided to verify the energy dissipation of the system and the convergence of the proposed approach.
文摘Capacitive voltage transformers (CVTs) are essential in high-voltage systems. An accurate error assessment is crucial for precise energy metering. However, tracking real-time quantitative changes in capacitive voltage transformer errors, particularly minor variations in multi-channel setups, remains challenging. This paper proposes a method for online error tracking of multi-channel capacitive voltage transformers using a Co-Prediction Matrix. The approach leverages the strong correlation between in-phase channels, particularly the invariance of the signal proportions among them. By establishing a co-prediction matrix based on these proportional relationships, The influence of voltage changes on the primary measurements is mitigated. Analyzing the relationships between the co-prediction matrices over time allows for inferring true measurement errors. Experimental validation with real-world data confirms the effectiveness of the method, demonstrating its capability to continuously track capacitive voltage transformer measurement errors online with precision over extended durations.
基金Supported by National Natural Science Foundation of China(Grant Nos.52375018,92148301).
文摘Contour error is the deviation between the actual displacement and reference trajectory,which is directly related to the machining accuracy.Contour error compensation poses substantial challenges because of the time-varying,nonlinear,and strongly coupled characteristics of parallel machining modules.In addition,the time delay in the system reduces the timeliness of the feedback data,thereby making online contour error calculations and compensation particularly difficult.To solve this problem,the generation mechanism of the time delay of the feedback data and contour error is revealed,and a systematic method for the identification of the time-delay parameter based on Beckhoff’s tracking error calculation mechanism is proposed.The temporal alignment between the position commands and feedback data enables the online calculation of the contour error.On this basis,the tracking error of the drive axes(an important factor resulting in end-effector contour errors)is used for the contour error calculation.Considering the ambiguous parameter-setting logic of the servo drive,the servo parameter is calculated in reverse using the steady-state error to obtain the tracking error model of the drive axes.Furthermore,combined with the system time-delay model,an online correction method for the tracking error estimation model is established.To achieve an accurate mapping of the drive-axis tracking error and end-effector contour error,a bounded iterative search method for the nearest contour point and online calculation model for the contour error are respectively established.Finally,an online compensation controller for contour error is designed.Its effectiveness is verified by a machining experiment on a frame workpiece.The machining results show that the contour error reduces from 68μm to 45μm,and the finish machining accuracy increases by 34%.This study provides a feasible method for online compensation of contour error in a system with time delay.
文摘In this paper, we proposed an output voltage stabilization of a DC-DC Zeta converter using hybrid control. We modeled the Zeta converter under continuous conduction mode operation. We derived a switching control law that brings the output voltage to the desired level. Due to infinite switching occurring at the desired level, we enhanced the switching control law by allowing a sizeable output voltage ripple. We derived mathematical models that allow one to choose the desired switching frequency. In practice, the existence of the non-ideal properties of the Zeta converter results in steady-state output voltage error. By analyzing the power loss in the zeta converter, we proposed an improved switching control law that eliminates the steady-state output voltage error. The effectiveness of the proposed method is illustrated with simulation results.
基金supported by the Key R&D Program of Zhejiang Province(Nos.2023C01166 and 2024SJCZX0046)the Zhejiang Provincial Natural Science Foundation of China(Nos.LDT23E05013E05 and LD24E050009)the Natural Science Foundation of Ningbo(No.2021J150),China.
文摘Accuracy allocation is crucial in the accuracy design of machining tools.Current accuracy allocation methods primarily focus on positional deviation,with little consideration for tool direction deviation.To address this issue,we propose a geometric error cost sensitivity-based accuracy allocation method for five-axis machine tools.A geometric error model consisting of 4l error components is constructed based on homogeneous transformation matrices.Volumetric points with positional and tool direction deviations are randomly sampled to evaluate the accuracy of the machine tool.The sensitivity of each error component at these sampling points is analyzed using the Sobol method.To balance the needs of geometric precision and manufacturing cost,a geometric error cost sensitivity function is developed to estimate the required cost.By allocating error components affecting tool direction deviation first and the remaining components second,this allocation scheme ensures that both deviations meet the requirements.We also perform numerical simulation of a BC-type(B-axis and C-axis type)five-axis machine tool to validate the method.The results show that the new allocation scheme reduces the total geometric error cost by 27.8%compared to a uniform allocation scheme,and yields the same positional and tool direction machining accuracies.
基金supported by the National Natural Science Foundation of China (62071144)
文摘Most of the existing direction of arrival(DOA)estimation algorithms are applied under the assumption that the array manifold is ideal.In practical engineering applications,the existence of non-ideal conditions such as mutual coupling between array elements,array amplitude and phase errors,and array element position errors leads to defects in the array manifold,which makes the performance of the algorithm decline rapidly or even fail.In order to solve the problem of DOA estimation in the presence of amplitude and phase errors and array element position errors,this paper introduces the first-order Taylor expansion equivalent model of the received signal under the uniform linear array from the Bayesian point of view.In the solution,the amplitude and phase error parameters and the array element position error parameters are regarded as random variables obeying the Gaussian distribution.At the same time,the expectation-maximization algorithm is used to update the probability distribution parameters,and then the two error parameters are solved alternately to obtain more accurate DOA estimation results.Finally,the effectiveness of the proposed algorithm is verified by simulation and experiment.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.12271394 and 62172341)the Sichuan Natural Science Foundation(Grant Nos.2024NSFSC1365 and 2024NSFSC1375)。
文摘The fragility and stochastic behavior of quantum sources make it crucial to witness the topology of quantum networks.Most previous theoretical methods are based on perfect assumptions of quantum measurements.In this work,we propose a method to witness network topology under imperfect assumptions of quantum measurements.We show that the discrimination between star and triangle networks depends on the specific error tolerances of local measurements.This extends recent results for witnessing the triangle network[Phys.Rev.Lett.132240801(2024)].
基金Project supported by the Scientific Research Foundation of Shanxi Institute of Technology(Grant No.201706001)the Fund for Shanxi "1331 Project" Key Subjects Construction+2 种基金the China Postdoctoral Science Foundation(Grant No.2017M612411)the Education Department Foundation of Henan Province,China(Grant No.18A140009)the National Natural Science Foundation of China(Grant Nos.61821280,11604190,and 61465013)
文摘Based on a hybrid system consisting of a quantum dot coupled with a double-sided micropillar cavity, we investigate the implementation of an error-detected photonic quantum routing controlled by the other photon. The computational errors from unexpected experimental imperfections are heralded by single photon detections, resulting in a unit fidelity for the present scheme, so that this scheme is intrinsically robust. We discuss the performance of the scheme with currently achievable experimental parameters. Our results show that the present scheme is efficient. Furthermore, our scheme could provide a promising building block for quantum networks and distributed quantum information processing in the future.
基金the National Key Research and Development Program of China(2022YFB3403404)the Youth Innovation Promotion Association,CAS(2022213)the National Natural Science Foundation of China(62127901 and 62305334).
文摘Null compensation interferometry is the primary testing method for the manufacture of ultra-high-precision aspheric mirrors.The crosstalk fringes generated by stray light in interferometry can affect accuracy and potentially prevent the testing from proceeding normally.Position errors include the decenter error,tilt error,and distance error.During the testing process,position errors will impact the testing accuracy and the crosstalk fringes generated by stray light.To determine the specific impact of position errors,we use the concept of Hindle shell testing of a convex aspheric mirror,and propose the simulation method of crosstalk fringes in null compensation interferometry.We also propose evaluation indices of crosstalk fringes in interferometry and simulate the influence of position errors on the crosstalk fringes.This work aims to help improve the design of compensation interferometry schemes,enhance the feasibility of the design,reduce engineering risks,and improve efficiency.
基金Project supported by the Natural Science Foundation of Shandong Province,China(Grant No.ZR2021MF049)Joint Fund of Natural Science Foundation of Shandong Province(Grant Nos.ZR2022LLZ012 and ZR2021LLZ001)the Key R&D Program of Shandong Province,China(Grant No.2023CXGC010901)。
文摘Quantum computing has the potential to solve complex problems that are inefficiently handled by classical computation.However,the high sensitivity of qubits to environmental interference and the high error rates in current quantum devices exceed the error correction thresholds required for effective algorithm execution.Therefore,quantum error correction technology is crucial to achieving reliable quantum computing.In this work,we study a topological surface code with a two-dimensional lattice structure that protects quantum information by introducing redundancy across multiple qubits and using syndrome qubits to detect and correct errors.However,errors can occur not only in data qubits but also in syndrome qubits,and different types of errors may generate the same syndromes,complicating the decoding task and creating a need for more efficient decoding methods.To address this challenge,we used a transformer decoder based on an attention mechanism.By mapping the surface code lattice,the decoder performs a self-attention process on all input syndromes,thereby obtaining a global receptive field.The performance of the decoder was evaluated under a phenomenological error model.Numerical results demonstrate that the decoder achieved a decoding accuracy of 93.8%.Additionally,we obtained decoding thresholds of 5%and 6.05%at maximum code distances of 7 and 9,respectively.These results indicate that the decoder used demonstrates a certain capability in correcting noise errors in surface codes.
基金Supported by Shanxi Provincial Natural Science Foundation(Grant No.2021JM010)The Youth Innovation Team of Shaanxi Universities.
文摘This study aimed to identify and compensate for the geometric errors of the double swiveling axes in a five-axis computer numerical control(CNC)machining center.Hence,a three-dimensional coordinate calculation algorithm for a measured point with additional rotational rigid body motion constraints is proposed.The motion constraints of the rotational rigid body were analyzed,and a mathematical model of the measured point algorithm in the swiveling axes was established.The Levenberg-Marquard method was used to solve the nonlinear superstatically determined equations.The spatial coordinate error was used to separate the spatial deviation of the measured point.An identification model of the position-independent and position-dependent geometric errors was established.The three-dimensional coordinate-solving algorithm of the measured point in the swiveling axis and geometric error identification method based on the Monte Carlo method were analyzed numerically.Geometric error measurement and cutting experiments were performed on a VMC25100U five-axis machining center,which integrated two swiveling axes.Geometric errors of the A-and B-axes were identified and measured experimentally.The angular positioning errors before and after compensation were measured using a laser interferometer,which verified the effectiveness of the proposed algorithm.A cutting experiment of a round table part was performed.The shape and position accuracy of the processed part before and after compensation were detected using a coordinate measuring machine.It verified that the geometric error of the swiveling axis was effectively compensated by the algorithm proposed herein.
文摘In bridge engineering,monitoring pier offsets is crucial for ensuring both structural safety and construction quality.The total station measurement method using a reflector is widely employed,offering significant advantages in specific scenarios.During measurements,errors are influenced by various factors.Initially,misalignment causes the lateral relative error to increase before decreasing,while longitudinal relative errors fluctuate due to instrument characteristics and operational factors.Lateral movements have a more pronounced impact on these errors.Investigating the positioning layout of pier offsets holds substantial importance as it enables precise displacement monitoring,prevents accidents,aids in maintenance planning,provides valuable references for design and construction,and enhances the pier’s resistance to deflection.Controlling and correcting subsequent errors is essential to ensure the overall safety of the bridge structure.
基金supported by the National Natural Science Foundation of China(Grant Nos.12325501,12047503,and 12247104)the Chinese Academy of Sciences(Grant No.ZDRW-XX-2022-3-02)P.Z.is partially supported by the Innovation Program for Quantum Science and Technology(Grant No.2021ZD0301900).
文摘Quantum error correction is essential for realizing fault-tolerant quantum computing,where both the efficiency and accuracy of the decoding algorithms play critical roles.In this work,we introduce the implementation of the PLANAR algorithm,a software framework designed for fast and exact decoding of quantum codes with a planar structure.The algorithm first converts the optimal decoding of quantum codes into a partition function computation problem of an Ising spin glass model.Then it utilizes the exact Kac–Ward formula to solve it.In this way,PLANAR offers the exact maximum likelihood decoding in polynomial complexity for quantum codes with a planar structure,including the surface code with independent code-capacity noise and the quantum repetition code with circuit-level noise.Unlike traditional minimumweight decoders such as minimum-weight perfect matching(MWPM),PLANAR achieves theoretically optimal performance while maintaining polynomial-time efficiency.In addition,to demonstrate its capabilities,we exemplify the implementation using the rotated surface code,a commonly used quantum error correction code with a planar structure,and show that PLANAR achieves a threshold of approximately p_(uc)≈0.109 under the depolarizing error model,with a time complexity scaling of O(N^(0.69)),where N is the number of spins in the Ising model.
文摘AIM:To compare refractive error and angle of deviation in patients with basic esotropia and basic exotropia.METHODS:A retrospective review was conducted on the medical records of patients with basic-type strabismus.Demographic data,refractive error,best-corrected distance visual acuity(BCVA),and the horizontal and vertical angle of deviation between basic esotropia and exotropia patients were compared.RESULTS:Among the 7129 patients(mean age 22.98±14.81y)evaluated,44.7%(3185 cases,54.9%male)exhibited basic-type esotropia,while 55.3%(3944 cases,53.9%male)presented with basic-type exotropia.Basic esotropia cases exhibited more hyperopic spherical equivalent measurements in both eyes(right:0.53±3.07 vs left:0.56±2.98 D)than those with basic exotropia(right eye:-0.33±2.84 vs left eye:-0.24±2.68 D,P<0.001 for both eyes).Patients with basic esotropia had significantly greater horizontal deviation angles(near:36.08±18.87 PD and far:35.56±18.75 PD)compared to those with basic exotropia(near:33.75±16.11 PD and far:33.26±15.90 PD,P<0.001).Conversely,patients with basic exotropia had slightly higher vertical deviation angles(near:1.67±5.80 PD and far:1.72±5.89 PD)compared to those with basic esotropia(near:1.12±4.57 PD and far:1.12±4.58 PD,P<0.001).Patients with basic esotropia underwent surgical intervention at younger ages compared to basic exotropia individuals(19.68±15.99 vs 25.66±13.20,P<0.001).CONCLUSION:Basic esotropia patients present more hyperopic refractive errors,better visual acuity,larger horizontal yet smaller vertical ocular misalignments,and tend to undergo strabismus surgery at younger ages relative to basic exotropia cases.
