Based on the fact that the shear stress along anchorage segment is neither linearly nor uniformly distributed, the load transfer mechanism of the tension type anchor was studied and the mechanical characteristic of an...Based on the fact that the shear stress along anchorage segment is neither linearly nor uniformly distributed, the load transfer mechanism of the tension type anchor was studied and the mechanical characteristic of anchorage segment was analyzed. Shear stress?strain relationship of soil surrounding anchorage body was simplified into three-folding-lines model consisting of elastic phase, elasto-plastic phase and residual phase considering its softening characteristic. Meanwhile, shear displacement method that has been extensively used in the analysis of pile foundation was introduced. Based on elasto-plastic theory, the distributions of displacement, shear stress and axial force along the anchorage segment of tension type anchor were obtained, and the formula for calculating the elastic limit load was also developed accordingly. Finally, an example was given to discuss the variation of stress and displacement in the anchorage segment with the loads exerted on the anchor, and a program was worked out to calculate the anchor maximum bearing capacity. The influence of some parameters on the anchor bearing capacity was discussed, and effective anchorage length was obtained simultaneously. The results show that the shear stress first increases and then decreases and finally trends to the residual strength with increase of distance from bottom of the anchorage body, the displacement increases all the time with the increase of distance from bottom of the anchorage body, and the increase of velocity gradually becomes greater.展开更多
The response displacement method(RDM)is recommended for the seismic analysis of underground structures in the transverse direction for many codes,including bases for design of structures-seismic actions for designing ...The response displacement method(RDM)is recommended for the seismic analysis of underground structures in the transverse direction for many codes,including bases for design of structures-seismic actions for designing geotechnical works(ISO 23469)and code for seismic design of urban rail transit structures(GB 50909-2014).However,there are some obvious limitations in the application of RDM.Springs and the shear stress of the soil could be approximately evaluated for the structures having a simple cross section,such as rectangular and circular structures.It is necessary to propose simplified seismic analysis methods for structures with complex cross sections.This paper refers to the idea of RDM and proposes three generalized response displacement methods(GRDM).In GRDM1,a part of the soil surrounding a structure is selected to generate a generalized underground structure with a rectangular cross section,and the same analysis model as RDM is applied to analyze the responses of the structure.In GRDM2,a hollow soil model without a generalized structure is used to compute the equivalent load caused by the relative displacement of the soil,and the soil-structure interaction model is applied to calculate the responses of the structure.In GRDM3,a continuous soil model is applied to compute the equivalent load caused by the relative displacement and shear stress of the soil,and the soil-structure interaction model is applied to analyze the responses of the structure,which is the same as the model used in GRDM2.The time-history analysis method(THAM)is used to evaluate the accuracy of the proposed simplified methods.Results show that the error of GRDM1 is about 20%,while the error is only 5%for GRDM2 and GRDM3.Among the three proposed methods,GRDM3 has obvious advantages regarding calculation efficiency and accuracy.Therefore,it is recommended to use GRDM3 for the seismic response analysis of underground structures that have conventional simple or complex cross sections.展开更多
The main task of fracture mechanics of rock masses is the study on the propagating mechanism of fractures in rock masses , which can be efficiently conducted by discontinuty displacement (DD) numerical evaluation . Fi...The main task of fracture mechanics of rock masses is the study on the propagating mechanism of fractures in rock masses , which can be efficiently conducted by discontinuty displacement (DD) numerical evaluation . Firstly ,the element stress and displacement are analysed and the principle and steps of the numerical calculation of stress intensity factor and fracture extension force are introduced .The numerical results of parallel and echelon fracture systems ,which are compared with real field fractures .are presented. Finally . a simple engineering application example is presented .展开更多
As the strict limitation of primary structure in traditional force method and displacement method in indeterminate analysis may lead to complicated high-order linear equations, a breakthrough of the limitation, i.e., ...As the strict limitation of primary structure in traditional force method and displacement method in indeterminate analysis may lead to complicated high-order linear equations, a breakthrough of the limitation, i.e., the application of irregular force method and irregular displacement method, would be introduced in this paper to ease the difficulty of hand computations. By using hyperstatic primary structures and partly chained primary structures, the primary structures of force method and displacement method are reformed, and the order of the system is decreased. The technique is explained through examples. The significance of the new method is summarized.展开更多
Based on the general displacement method and the basic hypothesis of the trial load method, a new advanced trial load method, the general displacement arch-cantilever element method, was proposed to derive the transfo...Based on the general displacement method and the basic hypothesis of the trial load method, a new advanced trial load method, the general displacement arch-cantilever element method, was proposed to derive the transformation relation of displacements and loads between the surface nodes and middle plane nodes. This method considers the nodes on upstream and downstream surfaces of the arch dam to be exit nodes （master nodes）, and the middle plane nodes to be slave nodes. According to the derived displacement and load transformation matrices, the equilibrium equation treating the displacement of middle plane nodes as a basic unknown variable is transformed into one that treats the displacement of upstream and downstream nodes as a basic unknown variable. Because the surface nodes have only three degrees of freedom （DOF）, this method can be directly coupled with the finite element method （FEM）, which is used for foundation simulation to analyze the stress of the arch dam with consideration of dam-foundation interaction. Moreover, using the FEM, the nodal load of the arch dam can be easily obtained. Case studies of a typical cylindrical arch dam and the Wudongde arch dam demonstrate the robustness and feasibility of the proposed method.展开更多
An extended displacement discontinuity method (EDDM) is proposed to analyze the stress wave propagation in jointed viscoelastic rock mass (VRM).The discontinuities in a rock mass are divided into two groups.The primar...An extended displacement discontinuity method (EDDM) is proposed to analyze the stress wave propagation in jointed viscoelastic rock mass (VRM).The discontinuities in a rock mass are divided into two groups.The primary group with an average geometrical size larger than or in the same order of magnitude of wavelength of a concerned stress wave is defined as 'macro-joints',while the secondary group with a high density and relatively small geometrical size compared to the wavelength is known as 'micro-defects'.The rock mass with micro-defects is modeled as an equivalent viscoelastic medium while the macro-joints in the rock mass are modeled explicitly as physical discontinuities.Viscoelastic properties of a micro-defected sedimentary rock are obtained by longitudinally impacting a cored long sedimentary rod with a pendulum.Wave propagation coefficient and dynamic viscoelastic modulus are measured.The EDDM is then successfully employed to analyze the wave propagation across macro-joint in VRM.The effect of the rock viscosity on the stress wave propagation is evaluated by comparing the results of VRM from the presented EDDM with those of an elastic rock mass (ERM) from the conventional displacement discontinuity method (CDDM).The CDDM is a special case of the EDDM under the condition that the rock viscosity is ignored.Comparison of the reflected and transmitted waves shows that the essential rock viscosity has a significant effect on stress wave attenuation.When a short propagation distance of a stress wave is considered,the results obtained from the CDDM approximate to the EDDM solutions,however,when the propagation distance is sufficiently long relative to the wavelength,the effect of rock viscosity on the stress wave propagation cannot be ignored.展开更多
A revised displacement discontinuity method(DDM) program is developed for the simulation of rock joint propagation and dilatancy analysis. The non-linear joint model used in the program adopts Barton-Bandis normal def...A revised displacement discontinuity method(DDM) program is developed for the simulation of rock joint propagation and dilatancy analysis. The non-linear joint model used in the program adopts Barton-Bandis normal deformation model, Kulhaway shear deformation model and Mohr-Coulomb criterion. The joint propagation criterion is based on the equivalent stress intensity factor which can be obtained by regression analysis. The simulated rock joint propagation accords well with the existing knowledge. The closure and opening of joint is investigated by DDM, and it is shown that if the opening volume of propagated joint is larger than closure volume of the old joint, the joint dilatancy occurs. The dilatancy condition is mainly controlled by the normal stiffness of the rock joint. When the normal stiffness is larger than the critical value, joint dilatancy occurs. The critical normal stiffness of rock joint changes with the joint-load angle, and joint dilatancy is most possible to occur at 30°.展开更多
A technique for modelling of three-dimensional(3D)quasi-statically propagating cracks in elastic bodies by the displacement discontinuity method(DDM)was described.When the crack is closed,the Mohr-coulomb rule on the ...A technique for modelling of three-dimensional(3D)quasi-statically propagating cracks in elastic bodies by the displacement discontinuity method(DDM)was described.When the crack is closed,the Mohr-coulomb rule on the two contacted surfaces of the crack must be satisfied.A simple iterative method was adopted in order to consider three different states of cracks.Under the assumption that the advance of the point on the crack front would occur only in the normal plane which is through this edge point,the maximum energy release rate criterion is modified to be used as the criterion for the crack growth.With discretization,the process of crack propagation can be seen as the advance of the vertices of the crack front.The program MCP3D was developed based on these theories to simulate the 3D quasi-static crack propagation.A numerical example of a penny-shaped crack subject to tension and compression in an infinite elastic media was analyzed with MCP3D,and the results in comparison with others' show that the present method for 3D crack propagation is effective.展开更多
The present research is focused on the numerical crack coalescence analysis of the micro-cracks and cracks produced during the cutting action of TBM disc cutters. The linear elastic fracture mechanics(LEFM) concepts a...The present research is focused on the numerical crack coalescence analysis of the micro-cracks and cracks produced during the cutting action of TBM disc cutters. The linear elastic fracture mechanics(LEFM) concepts and the maximum tangential stress criterion are used to investigate the micro crack propagation and its direction underneath the excavating discs. A higher order displacement discontinuity method with quadratic displacement discontinuity elements is used to estimate the stress intensity factors near the crack tips. Rock cutting mechanisms under single and double type discs are simulated by the proposed numerical method.The main purposes of the present modeling are to simulate the chip formation process of indented rocks by single and double discs.The effects of specific disc parameters(except speed) on the thrust force Ft, the rolling force Fr, and the specific energy ES are investigated. It has been shown that the specific energy(energy required to cut through a unit volume of rock) of the double disc is less than that of the single disc. Crack propagation in rocks under disc cutters is numerically modeled and the optimum ratio of disc spacing S to penetration depth Pd(i.e. S/Pd ratio) of about 10 is obtained, which is in good agreement with the theoretical and experimental results cited in the literature.展开更多
The displacement discontinuity method(DDM) is a kind of boundary element method aiming at modeling two-dimensional linear elastic crack problems. The singularity around the crack tip prevents the DDM from optimally co...The displacement discontinuity method(DDM) is a kind of boundary element method aiming at modeling two-dimensional linear elastic crack problems. The singularity around the crack tip prevents the DDM from optimally converging when the basis functions are polynomials of first order or higher. To overcome this issue,enlightened by the mapped finite element method(FEM) proposed in Ref. [13], we present an optimally convergent mapped DDM in this work, called the mapped DDM(MDDM). It is essentially based on approximating a much smoother function obtained by reformulating the problem with an appropriate auxiliary map. Two numerical examples of crack problems are presented in comparison with the conventional DDM. The results show that the proposed method improves the accuracy of the DDM; moreover, it yields an optimal convergence rate for quadratic interpolating polynomials.展开更多
The higher order displacement discontinuity method(HODDM) utilizing special crack tip elements has been used in the solution of linear elastic fracture mechanics(LEFM) problems. The paper has selected several example ...The higher order displacement discontinuity method(HODDM) utilizing special crack tip elements has been used in the solution of linear elastic fracture mechanics(LEFM) problems. The paper has selected several example problems from the fracture mechanics literature(with available analytical solutions) including center slant crack in an infinite and finite body, single and double edge cracks, cracks emanating from a circular hole. The numerical values of Mode Ⅰ and Mode Ⅱ SIFs for these problems using HODDM are in excellent agreement with analytical results(reaching up to 0.001% deviation from their analytical results). The HODDM is also compared with the XFEM and a modified XFEM results. The results show that the HODDM needs a considerably lower computational effort(with less than 400 nodes) than the XFEM and the modified XFEM(which needs more than 10000 nodes) to reach a much higher accuracy. The proposed HODDM offers higher accuracy and lower computation effort for a wide range of problems in LEFM.展开更多
The back analysis of initial stress is usually based on measured stress values, but the measuring of initial stress demands substantial investment. Therefore, amounts of underground engineering have no measured initia...The back analysis of initial stress is usually based on measured stress values, but the measuring of initial stress demands substantial investment. Therefore, amounts of underground engineering have no measured initial stress data, such as tunneling engineering. Focusing on this problem, a new back analysis method which does not need measured initial stress data is developed. The fault is assumed to be caused by initial load, the displacement discontinuity method (DDM) which considered non-linear fault is adopted to establish a numerical model of the engineering site, and the multivariable regression analysis of the initial stress field around the faults is carried out based on the fault throw. The result shows that the initial stress field around the faults is disturbed significantly, stress concentration appears in the tip zone, the regressive fault throw matches the measured values well, and the regressive initial stress field is reliable.展开更多
A 3D displacement discontinuity method is applied to solve the fracture mechanics problems of the mixed mode crack under compression.Friction between the surface of the closed crack is considered by establishing a sim...A 3D displacement discontinuity method is applied to solve the fracture mechanics problems of the mixed mode crack under compression.Friction between the surface of the closed crack is considered by establishing a simple and efficient iterative algorithm based on method of contact resistance mitigation.On the surfaces of the closed crack,the Mohr-coulomb rule is satisfied by iteration when the crack is in condition of sliding.The stress intensity factors are obtained using displacement fitting method.It is shown that the numerical results agree with the experimental results well and that friction plays an important role in resisting crack propagation.展开更多
In order to improve the precision of mining subsidence prediction, a mathematical model using Support Vector Machine （SVM） was established to calculate the displacement factor. The study is based on a comprehensive ...In order to improve the precision of mining subsidence prediction, a mathematical model using Support Vector Machine （SVM） was established to calculate the displacement factor. The study is based on a comprehensive analysis of factors affecting the displacement factor, such as mechanical properties of the cover rock, the ratio of mining depth to seam thickness, dip angle of the coal seam and the thickness of loose layer. Data of 63 typical observation stations were used as a training and testing sample set. A SVM regression model of the displacement factor and the factors affecting it was established with a kernel function, an insensitive loss factor and a properly selected penalty factor. Given an accurate calculation algorithm for testing and analysis, the results show that an SVM regression model can calcu- late displacement factor precisely and reliable precision can be obtained which meets engineering requirements. The experimental results show that the method to calculation of the displacement factor, based on the SVM method, is feasible. The many factors affecting the displacement factor can be consid- ered with this method. The research provides an efficient and accurate approach for the calculation of displacement in mining subsidence orediction.展开更多
An iterative algorithm for modeling of non-linear joint by the displacement discontinuity method (DDM) was described, and the effect of the non-linear joint on the in-situ stress field was investigated in this paper. ...An iterative algorithm for modeling of non-linear joint by the displacement discontinuity method (DDM) was described, and the effect of the non-linear joint on the in-situ stress field was investigated in this paper. The Barton-Bandis (BB) non-linear joint model and failure criterion were adopted in the new DDM program. Using this program, the stress field around the non-linear joint was obtained, the parameters analysis of the joint was carried out, and the deformation and stress distribution of the joint were studied. The simulation results show that: (1)the in-situ stress is significantly affected by the joint; (2)the increase of stiffness, friction angle, and thickness of the joint affect the stress concentration in different ways; (3)the influence distance of the joint changes with the angle of the joint; (4)the deformation and stress of the joint change with the point position.展开更多
In this paper the method of reciprocal theorem is extended to find solutions of three-D problems of elasticity.First we give the basic solution of the cube with six surfaces fixed as the basic system and then using th...In this paper the method of reciprocal theorem is extended to find solutions of three-D problems of elasticity.First we give the basic solution of the cube with six surfaces fixed as the basic system and then using the reciprocal theorem between the basic system acted on by unit concentrated loads and the actual system with prescribed surface displacements, we find displacement solution of the actual system.展开更多
Bisphenol A （BPA） is a chemical with high production volume and wide applications in many industries. Although BPA is known as an endocrine disruptor, its toxic mechanisms have not been fully characterized. Due to i...Bisphenol A （BPA） is a chemical with high production volume and wide applications in many industries. Although BPA is known as an endocrine disruptor, its toxic mechanisms have not been fully characterized. Due to its structural similarity to thyroid hormones thyroxine （T4） and triiodothyronine （T3）, one possible mechanism of BPA toxicity is disruption of hormone transport by competitive binding with the transport proteins. In this study, the binding interactions of BPA, T4, and T3 with three thyroid hormone transport proteins, human serum albumin （HSA）, transthyretin （TTR）, and thyroxine-binding globulin （TBG） were investigated by fluorescence measurement. Using two site-specific fluorescence probes dansylamide and dansyl-L-proline, the binding constants of BPA with HSA at drug site I and site II were determined as 2.90 × 10^4 and 3.14 × 10^4 L/mol, respectively. By monitoring the intrinsic fluorescence of tryptophan, a binding constant of 4.70 ×10^3 L/mol was obtained. Similarly, by employing 8-anilino-l-naphthalenesulfonic acid as fluorescence probe, the binding affinity of BPA with TTR and TBG was measured to be 3.10 × 10^5 and 5.90× 10^5 L/mol, respectively. In general, BPA showed lower binding affinity with the proteins than T3 did, and even lower affinity than T4. Using these binding constants, the amount of BPA which would bind to the transport proteins in human plasma was estimated. These results suggest that the concentrations of BPA commonly found in human plasma are probably not high enough to interfere with T4 transport.展开更多
A multi-casing structure in drilling engineering can be considered as an inhomogeneous body consisting of many different materials. The mechanical behavior of the inhomogeneous body in an infinite domain is very com- ...A multi-casing structure in drilling engineering can be considered as an inhomogeneous body consisting of many different materials. The mechanical behavior of the inhomogeneous body in an infinite domain is very com- plicated. In this paper, a detailed expression about the fictitious stress method of the boundary element method （BEM） is demonstrated for the inhomogeneous body. Then the fictitious stress method is deployed to investigate the stresses for the multi-casing structure under non-uniform loading conditions and an irregular wellbore. Three examples of the multi-casing structure in the borehole imply the high effectiveness of BEM for complex geometries related to the borehole in an infinite formation. The effects of casing eccentricity and the interfacial gap on the stress field are discussed. The eccentric casing takes the potential yield when the eccentric orientation is along the direction of Sh. Under different eccentric orientations, the yon Mises stress in the casing increases with increasing degree of eccentricity. The radial stress in the multi-casing structure is always continuous along the radius, but the circumferential stress is discontinuous at the interface. The radial stress decreases and the circumferential stress increases with the increasing of the interfacial gap between the adjacent materials.展开更多
Iterative methods based on finite element simulation are effective approaches to design mold shape to compensate springback in sheet metal forming. However, convergence rate of iterative methods is difficult to improv...Iterative methods based on finite element simulation are effective approaches to design mold shape to compensate springback in sheet metal forming. However, convergence rate of iterative methods is difficult to improve greatly. To increase the springback compensate speed of designing age forming mold, process of calculating springback for a certain mold with finite element method is analyzed. Springback compensation is abstracted as finding a solution for a set of nonlinear functions and a springback compensation algorithm is presented on the basis of quasi Newton method. The accuracy of algorithm is verified by developing an ABAQUS secondary development program with MATLAB. Three rectangular integrated panels of dimensions 710 mmx750 mm integrated panels with intersected ribs of 10 mm are selected to perform case studies. The algorithm is used to compute mold contours for the panels with cylinder, sphere and saddle contours respectively and it takes 57%, 22% and 33% iterations as compared to that of displacement adjustment （DA） method. At the end of iterations, maximum deviations on the three panels are 0.618 4 mm, 0.624 1 mm and 0.342 0 mm that are smaller than the deviations determined by DA method （0.740 8 mm, 0.740 8 mm and 0.713 7 mm respectively）. In following experimental verification, mold contour for another integrated panel with 400 ram^380 mm size is designed by the algorithm. Then the panel is age formed in an autoclave and measured by a three dimensional digital measurement devise. Deviation between measuring results and the panel＇s design contour is less than 1 mm. Finally, the iterations with different mesh sizes （40 mm, 35 mm, 30 mm, 25 mm, 20 mm） in finite element models are compared and found no considerable difference. Another possible compensation method, Broyden-Fletcher-Shanmo method, is also presented based on the solving nonlinear fimctions idea. The Broyden-Fletcher-Shanmo method is employed to compute mold contour for the second panel. It only takes 50% iterations compared to that of DA. The proposed method can serve a faster mold contour compensation method for sheet metal forming.展开更多
Arc-length-type and energy-type methods are two main strategies used in structural nonlinear tracing analysis, but the former is widely used due to the explicitness and clarity in conception, as well as the convenienc...Arc-length-type and energy-type methods are two main strategies used in structural nonlinear tracing analysis, but the former is widely used due to the explicitness and clarity in conception, as well as the convenience and reliability in calculation. It is very important to trace the complete load-deflection path in order to know comprehensively the characteristics of structures subjected to loads. Unfortunately, the nonlinear analysis techniques are only workable for tracing the limit-point-type equilibrium path. For the bifurcation-point-type path, most of them cannot secure a satisfactory result. In this paper, main arc-length-type methods are reviewed and compared, and the possible reasons of failures in tracing analysis are briefly discussed. Some improvements are proposed, a displacement perturbation method and a force perturbation method are presented for tracing the bifurcation-point-type paths. Finally, two examples are analyzed to verify the ideas, and some conclusions are drawn with respect to the arc-length-type methods.展开更多
基金Project(20050532021) supported by the Research Fund for the Doctoral Program of Higher Education
文摘Based on the fact that the shear stress along anchorage segment is neither linearly nor uniformly distributed, the load transfer mechanism of the tension type anchor was studied and the mechanical characteristic of anchorage segment was analyzed. Shear stress?strain relationship of soil surrounding anchorage body was simplified into three-folding-lines model consisting of elastic phase, elasto-plastic phase and residual phase considering its softening characteristic. Meanwhile, shear displacement method that has been extensively used in the analysis of pile foundation was introduced. Based on elasto-plastic theory, the distributions of displacement, shear stress and axial force along the anchorage segment of tension type anchor were obtained, and the formula for calculating the elastic limit load was also developed accordingly. Finally, an example was given to discuss the variation of stress and displacement in the anchorage segment with the loads exerted on the anchor, and a program was worked out to calculate the anchor maximum bearing capacity. The influence of some parameters on the anchor bearing capacity was discussed, and effective anchorage length was obtained simultaneously. The results show that the shear stress first increases and then decreases and finally trends to the residual strength with increase of distance from bottom of the anchorage body, the displacement increases all the time with the increase of distance from bottom of the anchorage body, and the increase of velocity gradually becomes greater.
基金National Natural Science Foundation of China under Grant No.52108453Natural Science Foundation of Jiangxi Province of China under Grant No.20212BAB214014+1 种基金National Key R&D Program of China under Grant No.2018YFC1504305Joint Funds of the National Natural Science Foundation of China under Grant No.U1839201。
文摘The response displacement method(RDM)is recommended for the seismic analysis of underground structures in the transverse direction for many codes,including bases for design of structures-seismic actions for designing geotechnical works(ISO 23469)and code for seismic design of urban rail transit structures(GB 50909-2014).However,there are some obvious limitations in the application of RDM.Springs and the shear stress of the soil could be approximately evaluated for the structures having a simple cross section,such as rectangular and circular structures.It is necessary to propose simplified seismic analysis methods for structures with complex cross sections.This paper refers to the idea of RDM and proposes three generalized response displacement methods(GRDM).In GRDM1,a part of the soil surrounding a structure is selected to generate a generalized underground structure with a rectangular cross section,and the same analysis model as RDM is applied to analyze the responses of the structure.In GRDM2,a hollow soil model without a generalized structure is used to compute the equivalent load caused by the relative displacement of the soil,and the soil-structure interaction model is applied to calculate the responses of the structure.In GRDM3,a continuous soil model is applied to compute the equivalent load caused by the relative displacement and shear stress of the soil,and the soil-structure interaction model is applied to analyze the responses of the structure,which is the same as the model used in GRDM2.The time-history analysis method(THAM)is used to evaluate the accuracy of the proposed simplified methods.Results show that the error of GRDM1 is about 20%,while the error is only 5%for GRDM2 and GRDM3.Among the three proposed methods,GRDM3 has obvious advantages regarding calculation efficiency and accuracy.Therefore,it is recommended to use GRDM3 for the seismic response analysis of underground structures that have conventional simple or complex cross sections.
基金The research is supported by the National Nature Science Foundation of China
文摘The main task of fracture mechanics of rock masses is the study on the propagating mechanism of fractures in rock masses , which can be efficiently conducted by discontinuty displacement (DD) numerical evaluation . Firstly ,the element stress and displacement are analysed and the principle and steps of the numerical calculation of stress intensity factor and fracture extension force are introduced .The numerical results of parallel and echelon fracture systems ,which are compared with real field fractures .are presented. Finally . a simple engineering application example is presented .
文摘As the strict limitation of primary structure in traditional force method and displacement method in indeterminate analysis may lead to complicated high-order linear equations, a breakthrough of the limitation, i.e., the application of irregular force method and irregular displacement method, would be introduced in this paper to ease the difficulty of hand computations. By using hyperstatic primary structures and partly chained primary structures, the primary structures of force method and displacement method are reformed, and the order of the system is decreased. The technique is explained through examples. The significance of the new method is summarized.
基金supported by the National Natural Science Foundation of China (Grant No. 90510017)
文摘Based on the general displacement method and the basic hypothesis of the trial load method, a new advanced trial load method, the general displacement arch-cantilever element method, was proposed to derive the transformation relation of displacements and loads between the surface nodes and middle plane nodes. This method considers the nodes on upstream and downstream surfaces of the arch dam to be exit nodes （master nodes）, and the middle plane nodes to be slave nodes. According to the derived displacement and load transformation matrices, the equilibrium equation treating the displacement of middle plane nodes as a basic unknown variable is transformed into one that treats the displacement of upstream and downstream nodes as a basic unknown variable. Because the surface nodes have only three degrees of freedom （DOF）, this method can be directly coupled with the finite element method （FEM）, which is used for foundation simulation to analyze the stress of the arch dam with consideration of dam-foundation interaction. Moreover, using the FEM, the nodal load of the arch dam can be easily obtained. Case studies of a typical cylindrical arch dam and the Wudongde arch dam demonstrate the robustness and feasibility of the proposed method.
文摘An extended displacement discontinuity method (EDDM) is proposed to analyze the stress wave propagation in jointed viscoelastic rock mass (VRM).The discontinuities in a rock mass are divided into two groups.The primary group with an average geometrical size larger than or in the same order of magnitude of wavelength of a concerned stress wave is defined as 'macro-joints',while the secondary group with a high density and relatively small geometrical size compared to the wavelength is known as 'micro-defects'.The rock mass with micro-defects is modeled as an equivalent viscoelastic medium while the macro-joints in the rock mass are modeled explicitly as physical discontinuities.Viscoelastic properties of a micro-defected sedimentary rock are obtained by longitudinally impacting a cored long sedimentary rod with a pendulum.Wave propagation coefficient and dynamic viscoelastic modulus are measured.The EDDM is then successfully employed to analyze the wave propagation across macro-joint in VRM.The effect of the rock viscosity on the stress wave propagation is evaluated by comparing the results of VRM from the presented EDDM with those of an elastic rock mass (ERM) from the conventional displacement discontinuity method (CDDM).The CDDM is a special case of the EDDM under the condition that the rock viscosity is ignored.Comparison of the reflected and transmitted waves shows that the essential rock viscosity has a significant effect on stress wave attenuation.When a short propagation distance of a stress wave is considered,the results obtained from the CDDM approximate to the EDDM solutions,however,when the propagation distance is sufficiently long relative to the wavelength,the effect of rock viscosity on the stress wave propagation cannot be ignored.
基金Project(2009318000046) supported by the Western Transport Technical Program of the Ministry of Transport,China
文摘A revised displacement discontinuity method(DDM) program is developed for the simulation of rock joint propagation and dilatancy analysis. The non-linear joint model used in the program adopts Barton-Bandis normal deformation model, Kulhaway shear deformation model and Mohr-Coulomb criterion. The joint propagation criterion is based on the equivalent stress intensity factor which can be obtained by regression analysis. The simulated rock joint propagation accords well with the existing knowledge. The closure and opening of joint is investigated by DDM, and it is shown that if the opening volume of propagated joint is larger than closure volume of the old joint, the joint dilatancy occurs. The dilatancy condition is mainly controlled by the normal stiffness of the rock joint. When the normal stiffness is larger than the critical value, joint dilatancy occurs. The critical normal stiffness of rock joint changes with the joint-load angle, and joint dilatancy is most possible to occur at 30°.
文摘A technique for modelling of three-dimensional(3D)quasi-statically propagating cracks in elastic bodies by the displacement discontinuity method(DDM)was described.When the crack is closed,the Mohr-coulomb rule on the two contacted surfaces of the crack must be satisfied.A simple iterative method was adopted in order to consider three different states of cracks.Under the assumption that the advance of the point on the crack front would occur only in the normal plane which is through this edge point,the maximum energy release rate criterion is modified to be used as the criterion for the crack growth.With discretization,the process of crack propagation can be seen as the advance of the vertices of the crack front.The program MCP3D was developed based on these theories to simulate the 3D quasi-static crack propagation.A numerical example of a penny-shaped crack subject to tension and compression in an infinite elastic media was analyzed with MCP3D,and the results in comparison with others' show that the present method for 3D crack propagation is effective.
文摘The present research is focused on the numerical crack coalescence analysis of the micro-cracks and cracks produced during the cutting action of TBM disc cutters. The linear elastic fracture mechanics(LEFM) concepts and the maximum tangential stress criterion are used to investigate the micro crack propagation and its direction underneath the excavating discs. A higher order displacement discontinuity method with quadratic displacement discontinuity elements is used to estimate the stress intensity factors near the crack tips. Rock cutting mechanisms under single and double type discs are simulated by the proposed numerical method.The main purposes of the present modeling are to simulate the chip formation process of indented rocks by single and double discs.The effects of specific disc parameters(except speed) on the thrust force Ft, the rolling force Fr, and the specific energy ES are investigated. It has been shown that the specific energy(energy required to cut through a unit volume of rock) of the double disc is less than that of the single disc. Crack propagation in rocks under disc cutters is numerically modeled and the optimum ratio of disc spacing S to penetration depth Pd(i.e. S/Pd ratio) of about 10 is obtained, which is in good agreement with the theoretical and experimental results cited in the literature.
基金the National Natural Science Foundation of China(No.11402146)the Young 1000 Talent Program of China
文摘The displacement discontinuity method(DDM) is a kind of boundary element method aiming at modeling two-dimensional linear elastic crack problems. The singularity around the crack tip prevents the DDM from optimally converging when the basis functions are polynomials of first order or higher. To overcome this issue,enlightened by the mapped finite element method(FEM) proposed in Ref. [13], we present an optimally convergent mapped DDM in this work, called the mapped DDM(MDDM). It is essentially based on approximating a much smoother function obtained by reformulating the problem with an appropriate auxiliary map. Two numerical examples of crack problems are presented in comparison with the conventional DDM. The results show that the proposed method improves the accuracy of the DDM; moreover, it yields an optimal convergence rate for quadratic interpolating polynomials.
文摘The higher order displacement discontinuity method(HODDM) utilizing special crack tip elements has been used in the solution of linear elastic fracture mechanics(LEFM) problems. The paper has selected several example problems from the fracture mechanics literature(with available analytical solutions) including center slant crack in an infinite and finite body, single and double edge cracks, cracks emanating from a circular hole. The numerical values of Mode Ⅰ and Mode Ⅱ SIFs for these problems using HODDM are in excellent agreement with analytical results(reaching up to 0.001% deviation from their analytical results). The HODDM is also compared with the XFEM and a modified XFEM results. The results show that the HODDM needs a considerably lower computational effort(with less than 400 nodes) than the XFEM and the modified XFEM(which needs more than 10000 nodes) to reach a much higher accuracy. The proposed HODDM offers higher accuracy and lower computation effort for a wide range of problems in LEFM.
基金the Western Transport Construction Science and Technology Project of the Ministry of Transport of the People's Republic of China(No.2009318000046)
文摘The back analysis of initial stress is usually based on measured stress values, but the measuring of initial stress demands substantial investment. Therefore, amounts of underground engineering have no measured initial stress data, such as tunneling engineering. Focusing on this problem, a new back analysis method which does not need measured initial stress data is developed. The fault is assumed to be caused by initial load, the displacement discontinuity method (DDM) which considered non-linear fault is adopted to establish a numerical model of the engineering site, and the multivariable regression analysis of the initial stress field around the faults is carried out based on the fault throw. The result shows that the initial stress field around the faults is disturbed significantly, stress concentration appears in the tip zone, the regressive fault throw matches the measured values well, and the regressive initial stress field is reliable.
文摘A 3D displacement discontinuity method is applied to solve the fracture mechanics problems of the mixed mode crack under compression.Friction between the surface of the closed crack is considered by establishing a simple and efficient iterative algorithm based on method of contact resistance mitigation.On the surfaces of the closed crack,the Mohr-coulomb rule is satisfied by iteration when the crack is in condition of sliding.The stress intensity factors are obtained using displacement fitting method.It is shown that the numerical results agree with the experimental results well and that friction plays an important role in resisting crack propagation.
基金the Research and Innovation Program for College and University Graduate Students in Jiangsu Province (No.CX10B_141Z)the National Natural Science Foundation of China (No.41071273) for support of this project
文摘In order to improve the precision of mining subsidence prediction, a mathematical model using Support Vector Machine （SVM） was established to calculate the displacement factor. The study is based on a comprehensive analysis of factors affecting the displacement factor, such as mechanical properties of the cover rock, the ratio of mining depth to seam thickness, dip angle of the coal seam and the thickness of loose layer. Data of 63 typical observation stations were used as a training and testing sample set. A SVM regression model of the displacement factor and the factors affecting it was established with a kernel function, an insensitive loss factor and a properly selected penalty factor. Given an accurate calculation algorithm for testing and analysis, the results show that an SVM regression model can calcu- late displacement factor precisely and reliable precision can be obtained which meets engineering requirements. The experimental results show that the method to calculation of the displacement factor, based on the SVM method, is feasible. The many factors affecting the displacement factor can be consid- ered with this method. The research provides an efficient and accurate approach for the calculation of displacement in mining subsidence orediction.
基金Western Transport Construction Science and Technology Project of the Ministry of Transport of China ( No. 2009318000046)
文摘An iterative algorithm for modeling of non-linear joint by the displacement discontinuity method (DDM) was described, and the effect of the non-linear joint on the in-situ stress field was investigated in this paper. The Barton-Bandis (BB) non-linear joint model and failure criterion were adopted in the new DDM program. Using this program, the stress field around the non-linear joint was obtained, the parameters analysis of the joint was carried out, and the deformation and stress distribution of the joint were studied. The simulation results show that: (1)the in-situ stress is significantly affected by the joint; (2)the increase of stiffness, friction angle, and thickness of the joint affect the stress concentration in different ways; (3)the influence distance of the joint changes with the angle of the joint; (4)the deformation and stress of the joint change with the point position.
文摘In this paper the method of reciprocal theorem is extended to find solutions of three-D problems of elasticity.First we give the basic solution of the cube with six surfaces fixed as the basic system and then using the reciprocal theorem between the basic system acted on by unit concentrated loads and the actual system with prescribed surface displacements, we find displacement solution of the actual system.
基金supported by the National Natural Science Foundation of China(No. 20890112,20921063,20825519)
文摘Bisphenol A （BPA） is a chemical with high production volume and wide applications in many industries. Although BPA is known as an endocrine disruptor, its toxic mechanisms have not been fully characterized. Due to its structural similarity to thyroid hormones thyroxine （T4） and triiodothyronine （T3）, one possible mechanism of BPA toxicity is disruption of hormone transport by competitive binding with the transport proteins. In this study, the binding interactions of BPA, T4, and T3 with three thyroid hormone transport proteins, human serum albumin （HSA）, transthyretin （TTR）, and thyroxine-binding globulin （TBG） were investigated by fluorescence measurement. Using two site-specific fluorescence probes dansylamide and dansyl-L-proline, the binding constants of BPA with HSA at drug site I and site II were determined as 2.90 × 10^4 and 3.14 × 10^4 L/mol, respectively. By monitoring the intrinsic fluorescence of tryptophan, a binding constant of 4.70 ×10^3 L/mol was obtained. Similarly, by employing 8-anilino-l-naphthalenesulfonic acid as fluorescence probe, the binding affinity of BPA with TTR and TBG was measured to be 3.10 × 10^5 and 5.90× 10^5 L/mol, respectively. In general, BPA showed lower binding affinity with the proteins than T3 did, and even lower affinity than T4. Using these binding constants, the amount of BPA which would bind to the transport proteins in human plasma was estimated. These results suggest that the concentrations of BPA commonly found in human plasma are probably not high enough to interfere with T4 transport.
基金supported by the China National High Technology Research and Development Program 863 (Grant No. 2013AA064503)The China Scholarship Council
文摘A multi-casing structure in drilling engineering can be considered as an inhomogeneous body consisting of many different materials. The mechanical behavior of the inhomogeneous body in an infinite domain is very com- plicated. In this paper, a detailed expression about the fictitious stress method of the boundary element method （BEM） is demonstrated for the inhomogeneous body. Then the fictitious stress method is deployed to investigate the stresses for the multi-casing structure under non-uniform loading conditions and an irregular wellbore. Three examples of the multi-casing structure in the borehole imply the high effectiveness of BEM for complex geometries related to the borehole in an infinite formation. The effects of casing eccentricity and the interfacial gap on the stress field are discussed. The eccentric casing takes the potential yield when the eccentric orientation is along the direction of Sh. Under different eccentric orientations, the yon Mises stress in the casing increases with increasing degree of eccentricity. The radial stress in the multi-casing structure is always continuous along the radius, but the circumferential stress is discontinuous at the interface. The radial stress decreases and the circumferential stress increases with the increasing of the interfacial gap between the adjacent materials.
文摘Iterative methods based on finite element simulation are effective approaches to design mold shape to compensate springback in sheet metal forming. However, convergence rate of iterative methods is difficult to improve greatly. To increase the springback compensate speed of designing age forming mold, process of calculating springback for a certain mold with finite element method is analyzed. Springback compensation is abstracted as finding a solution for a set of nonlinear functions and a springback compensation algorithm is presented on the basis of quasi Newton method. The accuracy of algorithm is verified by developing an ABAQUS secondary development program with MATLAB. Three rectangular integrated panels of dimensions 710 mmx750 mm integrated panels with intersected ribs of 10 mm are selected to perform case studies. The algorithm is used to compute mold contours for the panels with cylinder, sphere and saddle contours respectively and it takes 57%, 22% and 33% iterations as compared to that of displacement adjustment （DA） method. At the end of iterations, maximum deviations on the three panels are 0.618 4 mm, 0.624 1 mm and 0.342 0 mm that are smaller than the deviations determined by DA method （0.740 8 mm, 0.740 8 mm and 0.713 7 mm respectively）. In following experimental verification, mold contour for another integrated panel with 400 ram^380 mm size is designed by the algorithm. Then the panel is age formed in an autoclave and measured by a three dimensional digital measurement devise. Deviation between measuring results and the panel＇s design contour is less than 1 mm. Finally, the iterations with different mesh sizes （40 mm, 35 mm, 30 mm, 25 mm, 20 mm） in finite element models are compared and found no considerable difference. Another possible compensation method, Broyden-Fletcher-Shanmo method, is also presented based on the solving nonlinear fimctions idea. The Broyden-Fletcher-Shanmo method is employed to compute mold contour for the second panel. It only takes 50% iterations compared to that of DA. The proposed method can serve a faster mold contour compensation method for sheet metal forming.
基金The project supported by the Special Research Fund for Doctor Program of Universities (9424702)
文摘Arc-length-type and energy-type methods are two main strategies used in structural nonlinear tracing analysis, but the former is widely used due to the explicitness and clarity in conception, as well as the convenience and reliability in calculation. It is very important to trace the complete load-deflection path in order to know comprehensively the characteristics of structures subjected to loads. Unfortunately, the nonlinear analysis techniques are only workable for tracing the limit-point-type equilibrium path. For the bifurcation-point-type path, most of them cannot secure a satisfactory result. In this paper, main arc-length-type methods are reviewed and compared, and the possible reasons of failures in tracing analysis are briefly discussed. Some improvements are proposed, a displacement perturbation method and a force perturbation method are presented for tracing the bifurcation-point-type paths. Finally, two examples are analyzed to verify the ideas, and some conclusions are drawn with respect to the arc-length-type methods.
