In this work, a survey of companies has been produc ed from a questionnaire and in-depth inter-views. The aimof the paper is to give a current view of the use of DES (Discrete- Event Simulation) in the indust ry. The ...In this work, a survey of companies has been produc ed from a questionnaire and in-depth inter-views. The aimof the paper is to give a current view of the use of DES (Discrete- Event Simulation) in the indust ry. The companies have been selected in a wide range in e.g. size, capital turno ver and employees. The survey was restricted to Sweden, although the results may be applicable to other countries with similar industrial structure. Some of the companies investigated are also multinational with branches around the world. T o illustrate the differences in production systems different sectors have be en investigated, e.g. the manufacturing industry and energy sector. The manufact uring systems generally differ in that the energy sector is more known for high reliability in their systems and the manufacturing sector tends to work more wit h lean production. Previous surveys of manufacturing efficiency illustrate different aspects. Accor ding to one survey, more than one-third (34%) of the disturbances in two countr ies (the U.S. and Finland) were mainly caused by design-based errors and flaws. The survey also showed the scope of safety problems experienced in the implemen tation and use of flexible manufacturing systems (Jrvinen et al., 1996). Another survey in Germany reports a gap between users and non-users of DES. Man y companies that are not familiar with simulation are not aware of its benefits. The study suggested integrating simulation into the planning processes as a reg ular tool. So far, DES is mostly used in system planning, resource planning and scheduling and production planning (Hirschberg & Heitmann, 1997). The disposition of the accomplished questionnaire had been multiple-choice ques tions in a strict order. The respondents gave their views on what the interviewe r considered relevant for the survey. The questionnaire was mailed to 220 person s in May 2001; a second round for unanswered surveys was dispatched in August 20 01. Replies came from 114 respondents; thus, the reply rate to all questionnaire s sent out was 52%. The replies came in from 80 different companies. Questionswere raised regarding what kinds of decisions are taken from a simulation projec t and questions were also asked regarding the tool itself. Some common problems encountered based on the authors’ knowledge were asked in the questionnaire. The questions were sent to those who had reasonable knowledge of how to work with D ES. Supplementary in-depth interviews were also accomplished. On the question if DES facilitates the decision-making process 79% of totally 3 8 answered to a very large or a large extent. Regarding the question if DES is a useful tool for measuring the availability of equipment for example system verification 73% of 33 responded to a very large or a large extent. A majority o f the respondents genuinely see an advantage with the use of simulation, which i s an important result from the study. The cost reduction aspect of the productio n is also an advantage of DES. On the question eight answered to a very large ex tent and 23 to a large extent of total 39 replies. The question demonstrates tha t the results of a simulation model are indeed used in the real world. Finally, in the question of DES is used for staffing it is indicated that it is not so co mmonly used as for other functions asked for. The staffing issue requires good k nowledge about time measurement of manual labor. The option, however, to include manual work in a simulation model is in many programs extensive and must be a v aluable option to evaluate work intensive parts of production lines and their im provement. To conclude, it could be mentioned that DES is a tool with potential. The use is increasing and 12 of 80 companies investigated in Sweden 2001 are using it, an increase compared to previous stud-ies. Of those 12 companies, four are using t he tool to a large extent. The main advantage according to the survey beside the visualization part is that the knowledge about a system is investigated and doc umented.展开更多
The Riyadh metro project is one of the current megaprojects that aim to improve the transit systems in Saudi Arabia.It consists of several metro lines with a total length of 176 km and 85 stations.The viaducts are con...The Riyadh metro project is one of the current megaprojects that aim to improve the transit systems in Saudi Arabia.It consists of several metro lines with a total length of 176 km and 85 stations.The viaducts are considered as one of the main construction elements in the metro lines.Four methods for viaducts construction have been used in the Riyadh metro project:precast beam,full span launching method,cast on-site,and segment method(precast segment method and BCM(balanced cantilever method)).The viaducts work consumes a large portion of a project’s time and cost.Furthermore,the competitive nature of the construction industry increases the need to improve the efficiency of construction performance.Accordingly,this paper takes the initial steps toward increasing the efficiency of viaduct construction methods through simulation.Simulation of construction processes provides a systematic tool that can be used for determining the resources,time,and cost of these processes.The simulation processes should focus on the main activities affecting this element’s execution for viaducts construction,such as segment storage,handling,transporting,and installation.This study highlights the viaducts construction methods and develops general discrete-event simulation models for the most commonly used viaducts construction methods in the Riyadh metro using AnyLogic simulation software.The simulation models visualize and capture the interaction between the different activities and resources in a viaduct construction.Consequently,the construction drawbacks can be identified.Furthermore,the simulation model can be manipulated by adding assumptions to develop more efficient construction methods in terms of time and cost in such projects.展开更多
The goal of this paper is to provide an approach to investigate the variation of fiber quantity in a certain cross-section of the drafting zone. This model with discrete-event simulation( DES)method was presented to s...The goal of this paper is to provide an approach to investigate the variation of fiber quantity in a certain cross-section of the drafting zone. This model with discrete-event simulation( DES)method was presented to simulate the dynamic drafting process. This model described the behavior of individual fibers,which was divided into four phases and simulated by corresponding modules. Three sets of processing conditions in industry were simulated and demonstrated the applications of this model. The comparison between experiments and simulation results could also validate this model. This model could be used to simulate various drafting process with appropriate drafting settings.展开更多
Object-oriented world-view provides a natural and powerful paradignl for expressing system elements and their dynamic behaviour for discrete-event simulation. Simulation gives the critical ability to study the dynamic...Object-oriented world-view provides a natural and powerful paradignl for expressing system elements and their dynamic behaviour for discrete-event simulation. Simulation gives the critical ability to study the dynamic behaviour of the models that are defined with object-voriented means. This paper first examines the ways of applying the object-oriented world-view to three major discrete simulation modelling approaches, then considers the process and merits of object-oriented simulation modelling.展开更多
Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing addit...Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.展开更多
Centrifugal casting of ductile iron pipe is a high-temperature,semi-continuous production process.However,conducting laboratory research on the solidification process of centrifugal casting of ductile iron pipe presen...Centrifugal casting of ductile iron pipe is a high-temperature,semi-continuous production process.However,conducting laboratory research on the solidification process of centrifugal casting of ductile iron pipe presents significant challenges.In this study,a novel research method was introduced for investigating the solidification process of ductile iron pipe,namely thermal simulation of ductile iron pipe.Comparative research was conducted on the microstructure and properties of the thermal simulation sample and the ductile iron pipe.The findings indicate that the thermal simulation sample and ductile iron pipe exhibit good heat transfer similarity and microstructure similarity.The difference of cooling rate between thermal simulation sample and ductile pipe is less than 0.24℃·s^(-1),and the difference of microstructure content of free cementite,ferrite,and pearlite is less than 5%.The tensile strength of annealed ductile iron pipe is 466 MPa,with an elongation of 16.1%and a Brinell hardness of 156.5 HBW.In comparison,the tensile strength of annealed thermal simulation sample is 482.0 MPa,with an elongation of 15.5%and a Brinell hardness of 159.0 HBW.These results suggest that the thermal simulation experimental research method is both scientific and feasible,offering an objective,reliable,and cost-effective approach to laboratory research on ductile iron pipe.展开更多
BACKGROUND Orthopaedic surgical education has traditionally depended on the apprenticeship model of“see one,do one,teach one”.However,reduced operative exposure,stricter work-hour regulations,medicolegal constraints...BACKGROUND Orthopaedic surgical education has traditionally depended on the apprenticeship model of“see one,do one,teach one”.However,reduced operative exposure,stricter work-hour regulations,medicolegal constraints,and patient safety concerns have constrained its practicality.Simulation-based training has become a reliable,safe,and cost-efficient alternative.Dry lab techniques,especially virtual and augmented reality,make up 78%of current dry lab research,whereas wet labs still set the standard for anatomical realism.AIM To evaluate the effectiveness,limitations,and future directions of wet and dry lab simulation in orthopaedic training.METHODS A scoping review was carried out across four databases-PubMed,Cochrane Library,Web of Science,and EBSCOhost-up to 2025.Medical Subject Headings included:"Orthopaedic Education","Wet Lab","Dry Lab","Simulation Training","Virtual Reality",and"Surgical Procedure".Eligible studies focused on orthopaedic or spinal surgical education,employed wet or dry lab techniques,and assessed training effectiveness.Exclusion criteria consisted of non-English publications,abstracts only,non-orthopaedic research,and studies unrelated to simulation.Two reviewers independently screened titles,abstracts,and full texts,resolving discrepancies with a third reviewer.RESULTS From 1851 records,101 studies met inclusion:78 on dry labs,7 on wet labs,4 on both.Virtual reality(VR)simulations were most common,with AI increasingly used for feedback and assessment.Cadaveric training remains the gold standard for accuracy and tactile feedback,while dry labs-especially VR-offer scalability,lower cost(40%-60%savings in five studies),and accessibility for novices.Senior residents prefer wet labs for complex tasks;juniors favour dry labs for basics.Challenges include limited transferability data,lack of standard outcome metrics,and ethical concerns about cadaver use and AI assessment.CONCLUSION Wet and dry labs each have unique strengths in orthopaedic training.A hybrid approach combining both,supported by standardised assessments and outcome studies,is most effective.Future efforts should aim for uniform reporting,integrating new technologies,and policy support for hybrid curricula to enhance skills and patient care.展开更多
This study introduces a new ocean surface friction velocity scheme and a modified Thompson cloud microphysics parameterization scheme into the CMA-TYM model.The impact of these two parameterization schemes on the pred...This study introduces a new ocean surface friction velocity scheme and a modified Thompson cloud microphysics parameterization scheme into the CMA-TYM model.The impact of these two parameterization schemes on the prediction of the movement track and intensity of Typhoon Kompasu in 2021 is examined.Additionally,the possible reasons for their effects on tropical cyclone(TC)intensity prediction are analyzed.Statistical results show that both parameterization schemes improve the predictions of Typhoon Kompasu’s track and intensity.The influence on track prediction becomes evident after 60 h of model integration,while the significant positive impact on intensity prediction is observed after 66 h.Further analysis reveals that these two schemes affect the timing and magnitude of extreme TC intensity values by influencing the evolution of the TC’s warm-core structure.展开更多
Automation and intelligence have become the primary trends in the design of investment casting processes.However,the design of gating and riser systems still lacks precise quantitative evaluation criteria.Numerical si...Automation and intelligence have become the primary trends in the design of investment casting processes.However,the design of gating and riser systems still lacks precise quantitative evaluation criteria.Numerical simulation plays a significant role in quantitatively evaluating current processes and making targeted improvements,but its limitations lie in the inability to dynamically reflect the formation outcomes of castings under varying process conditions,making real-time adjustments to gating and riser designs challenging.In this study,an automated design model for gating and riser systems based on integrated parametric 3D modeling-simulation framework is proposed,which enhances the flexibility and usability of evaluating the casting process by simulation.Firstly,geometric feature extraction technology is employed to obtain the geometric information of the target casting.Based on this information,an automated design framework for gating and riser systems is established,incorporating multiple structural parameters for real-time process control.Subsequently,the simulation results for various structural parameters are analyzed,and the influence of these parameters on casting formation is thoroughly investigated.Finally,the optimal design scheme is generated and validated through experimental verification.Simulation analysis and experimental results show that using a larger gate neck(24 mm in side length) and external risers promotes a more uniform temperature distribution and a more stable flow state,effectively eliminating shrinkage cavities and enhancing process yield by 15%.展开更多
Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The t...Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.展开更多
Compared to the well-studied two-dimensional(2D)ferroelectricity,the appearance of 2D antiferroelectricity is much rarer,where local dipoles from the nonequivalent sublattices within 2D monolayers are oppositely orien...Compared to the well-studied two-dimensional(2D)ferroelectricity,the appearance of 2D antiferroelectricity is much rarer,where local dipoles from the nonequivalent sublattices within 2D monolayers are oppositely oriented.Using NbOCl_(2) monolayer with competing ferroelectric(FE)and antiferroelectric(AFE)phases as a 2D material platform,we demonstrate the emergence of intrinsic antiferroelectricity in NbOCl_(2) monolayer under experimentally accessible shear strain,along with new functionality associated with electric field-induced AFE-to-FE phase transition.Specifically,the complex configuration space accommodating FE and AFE phases,polarization switching kinetics,and finite temperature thermodynamic properties of 2D NbOCl_(2) are all accurately predicted by large-scale molecular dynamics simulations based on deep learning interatomic potential model.Moreover,room temperature stable antiferroelectricity with low polarization switching barrier and one-dimensional collinear polarization arrangement is predicted in shear-deformed NbOCl_(2) monolayer.The transition from AFE to FE phase in 2D NbOCl_(2) can be triggered by a low critical electric field,leading to a double polarization–electric(P–E)loop with small hysteresis.A new type of optoelectronic device composed of AFE-NbOCl_(2) is proposed,enabling electric“writing”and nonlinear optical“reading”logical operation with fast operation speed and low power consumption.展开更多
Analysis of the environmental and economic performance of fishing vessels has received limited attention compared with other ship types despite their notable contribution to global greenhouse gas(GHG)emissions.This st...Analysis of the environmental and economic performance of fishing vessels has received limited attention compared with other ship types despite their notable contribution to global greenhouse gas(GHG)emissions.This study evaluates the carbon footprint(CF)and economic viability of a liquefied natural gas(LNG)-fueled fishing vessel,using real engine operation simulations to provide precise and dynamic evaluation of fuel consumption and GHG emissions.Operational profiles are obtained through the utilization of onboard monitoring systems,whereas engine performance is simulated using the 1D/0D AVL Boost^(TM)model.Life cycle assessment(LCA)is conducted to quantify the environmental impact,whereas life cycle cost assessment(LCCA)is performed to analyze the profitability of LNG as an alternative fuel.The potential impact of the future fuel price uncertainties is addressed using Monte Carlo simulations.The LCA findings indicate that LNG has the potential to reduce the CF of the vessel by 14%to 16%,in comparison to a diesel power system configuration that serves as the baseline scenario.The LCCA results further indicate that the total cost of an LNG-powered ship is lower by 9.5%-13.8%,depending on the share of LNG and pilot fuels.This finding highlights the potential of LNG to produce considerable environmental benefits while addressing economic challenges under diverse operational and fuel price conditions.展开更多
Spike neural networks are inspired by animal brains,and outperform traditional neural networks on complicated tasks.However,spike neural networks are usually used on a large scale,and they cannot be computed on commer...Spike neural networks are inspired by animal brains,and outperform traditional neural networks on complicated tasks.However,spike neural networks are usually used on a large scale,and they cannot be computed on commercial,off-the-shelf computers.A parallel architecture is proposed and developed for discrete-event simulations of spike neural networks.Furthermore,mechanisms for both parallelism degree estimation and dynamic load balance are emphasized with theoretical and computational analysis.Simulation results show the effectiveness of the proposed parallelized spike neural network system and its corresponding support components.展开更多
Data collected from truck payload management systems at various surface mines shows that the payload variance is significant and must be considered in analysing the mine productivity,energy consumption,greenhouse gas ...Data collected from truck payload management systems at various surface mines shows that the payload variance is significant and must be considered in analysing the mine productivity,energy consumption,greenhouse gas emissions and associated cost.Payload variance causes significant differences in gross vehicle weights.Heavily loaded trucks travel slower up ramps than lightly loaded trucks.Faster trucks are slowed by the presence of slower trucks,resulting in‘bunching’,production losses and increasing fuel consumptions.This paper simulates the truck bunching phenomena in large surface mines to improve truck and shovel systems’efficiency and minimise fuel consumption.The study concentrated on completing a practical simulation model based on a discrete event method which is most commonly used in this field of research in other industries.The simulation model has been validated by a dataset collected from a large surface mine in Arizona state,USA.The results have shown that there is a good agreement between the actual and estimated values of investigated parameters.展开更多
文摘In this work, a survey of companies has been produc ed from a questionnaire and in-depth inter-views. The aimof the paper is to give a current view of the use of DES (Discrete- Event Simulation) in the indust ry. The companies have been selected in a wide range in e.g. size, capital turno ver and employees. The survey was restricted to Sweden, although the results may be applicable to other countries with similar industrial structure. Some of the companies investigated are also multinational with branches around the world. T o illustrate the differences in production systems different sectors have be en investigated, e.g. the manufacturing industry and energy sector. The manufact uring systems generally differ in that the energy sector is more known for high reliability in their systems and the manufacturing sector tends to work more wit h lean production. Previous surveys of manufacturing efficiency illustrate different aspects. Accor ding to one survey, more than one-third (34%) of the disturbances in two countr ies (the U.S. and Finland) were mainly caused by design-based errors and flaws. The survey also showed the scope of safety problems experienced in the implemen tation and use of flexible manufacturing systems (Jrvinen et al., 1996). Another survey in Germany reports a gap between users and non-users of DES. Man y companies that are not familiar with simulation are not aware of its benefits. The study suggested integrating simulation into the planning processes as a reg ular tool. So far, DES is mostly used in system planning, resource planning and scheduling and production planning (Hirschberg & Heitmann, 1997). The disposition of the accomplished questionnaire had been multiple-choice ques tions in a strict order. The respondents gave their views on what the interviewe r considered relevant for the survey. The questionnaire was mailed to 220 person s in May 2001; a second round for unanswered surveys was dispatched in August 20 01. Replies came from 114 respondents; thus, the reply rate to all questionnaire s sent out was 52%. The replies came in from 80 different companies. Questionswere raised regarding what kinds of decisions are taken from a simulation projec t and questions were also asked regarding the tool itself. Some common problems encountered based on the authors’ knowledge were asked in the questionnaire. The questions were sent to those who had reasonable knowledge of how to work with D ES. Supplementary in-depth interviews were also accomplished. On the question if DES facilitates the decision-making process 79% of totally 3 8 answered to a very large or a large extent. Regarding the question if DES is a useful tool for measuring the availability of equipment for example system verification 73% of 33 responded to a very large or a large extent. A majority o f the respondents genuinely see an advantage with the use of simulation, which i s an important result from the study. The cost reduction aspect of the productio n is also an advantage of DES. On the question eight answered to a very large ex tent and 23 to a large extent of total 39 replies. The question demonstrates tha t the results of a simulation model are indeed used in the real world. Finally, in the question of DES is used for staffing it is indicated that it is not so co mmonly used as for other functions asked for. The staffing issue requires good k nowledge about time measurement of manual labor. The option, however, to include manual work in a simulation model is in many programs extensive and must be a v aluable option to evaluate work intensive parts of production lines and their im provement. To conclude, it could be mentioned that DES is a tool with potential. The use is increasing and 12 of 80 companies investigated in Sweden 2001 are using it, an increase compared to previous stud-ies. Of those 12 companies, four are using t he tool to a large extent. The main advantage according to the survey beside the visualization part is that the knowledge about a system is investigated and doc umented.
文摘The Riyadh metro project is one of the current megaprojects that aim to improve the transit systems in Saudi Arabia.It consists of several metro lines with a total length of 176 km and 85 stations.The viaducts are considered as one of the main construction elements in the metro lines.Four methods for viaducts construction have been used in the Riyadh metro project:precast beam,full span launching method,cast on-site,and segment method(precast segment method and BCM(balanced cantilever method)).The viaducts work consumes a large portion of a project’s time and cost.Furthermore,the competitive nature of the construction industry increases the need to improve the efficiency of construction performance.Accordingly,this paper takes the initial steps toward increasing the efficiency of viaduct construction methods through simulation.Simulation of construction processes provides a systematic tool that can be used for determining the resources,time,and cost of these processes.The simulation processes should focus on the main activities affecting this element’s execution for viaducts construction,such as segment storage,handling,transporting,and installation.This study highlights the viaducts construction methods and develops general discrete-event simulation models for the most commonly used viaducts construction methods in the Riyadh metro using AnyLogic simulation software.The simulation models visualize and capture the interaction between the different activities and resources in a viaduct construction.Consequently,the construction drawbacks can be identified.Furthermore,the simulation model can be manipulated by adding assumptions to develop more efficient construction methods in terms of time and cost in such projects.
基金the Key Grant Project of Ministry of Education of the People’s Republic of China through Project,China(No.113027A)the Fundamental Research Funds for the Central Universities,China
文摘The goal of this paper is to provide an approach to investigate the variation of fiber quantity in a certain cross-section of the drafting zone. This model with discrete-event simulation( DES)method was presented to simulate the dynamic drafting process. This model described the behavior of individual fibers,which was divided into four phases and simulated by corresponding modules. Three sets of processing conditions in industry were simulated and demonstrated the applications of this model. The comparison between experiments and simulation results could also validate this model. This model could be used to simulate various drafting process with appropriate drafting settings.
文摘Object-oriented world-view provides a natural and powerful paradignl for expressing system elements and their dynamic behaviour for discrete-event simulation. Simulation gives the critical ability to study the dynamic behaviour of the models that are defined with object-voriented means. This paper first examines the ways of applying the object-oriented world-view to three major discrete simulation modelling approaches, then considers the process and merits of object-oriented simulation modelling.
基金National Key Research and Development Program of China(2022YFB4600902)Shandong Provincial Science Foundation for Outstanding Young Scholars(ZR2024YQ020)。
文摘Wire arc additive manufacturing(WAAM)has emerged as a promising approach for fabricating large-scale components.However,conventional WAAM still faces challenges in optimizing microstructural evolution,minimizing additive-induced defects,and alleviating residual stress and deformation,all of which are critical for enhancing the mechanical performance of the manufactured parts.Integrating interlayer friction stir processing(FSP)into WAAM significantly enhances the quality of deposited materials.However,numerical simulation research focusing on elucidating the associated thermomechanical coupling mechanisms remains insufficient.A comprehensive numerical model was developed to simulate the thermomechanical coupling behavior in friction stir-assisted WAAM.The influence of post-deposition FSP on the coupled thermomechanical response of the WAAM process was analyzed quantitatively.Moreover,the residual stress distribution and deformation behavior under both single-layer and multilayer deposition conditions were investigated.Thermal analysis of different deposition layers in WAAM and friction stir-assisted WAAM was conducted.Results show that subsequent layer deposition induces partial remelting of the previously solidified layer,whereas FSP does not cause such remelting.Furthermore,thermal stress and deformation analysis confirm that interlayer FSP effectively mitigates residual stresses and distortion in WAAM components,thereby improving their structural integrity and mechanical properties.
基金financially supported by the National Natural Science Foundation of China(52130109)。
文摘Centrifugal casting of ductile iron pipe is a high-temperature,semi-continuous production process.However,conducting laboratory research on the solidification process of centrifugal casting of ductile iron pipe presents significant challenges.In this study,a novel research method was introduced for investigating the solidification process of ductile iron pipe,namely thermal simulation of ductile iron pipe.Comparative research was conducted on the microstructure and properties of the thermal simulation sample and the ductile iron pipe.The findings indicate that the thermal simulation sample and ductile iron pipe exhibit good heat transfer similarity and microstructure similarity.The difference of cooling rate between thermal simulation sample and ductile pipe is less than 0.24℃·s^(-1),and the difference of microstructure content of free cementite,ferrite,and pearlite is less than 5%.The tensile strength of annealed ductile iron pipe is 466 MPa,with an elongation of 16.1%and a Brinell hardness of 156.5 HBW.In comparison,the tensile strength of annealed thermal simulation sample is 482.0 MPa,with an elongation of 15.5%and a Brinell hardness of 159.0 HBW.These results suggest that the thermal simulation experimental research method is both scientific and feasible,offering an objective,reliable,and cost-effective approach to laboratory research on ductile iron pipe.
文摘BACKGROUND Orthopaedic surgical education has traditionally depended on the apprenticeship model of“see one,do one,teach one”.However,reduced operative exposure,stricter work-hour regulations,medicolegal constraints,and patient safety concerns have constrained its practicality.Simulation-based training has become a reliable,safe,and cost-efficient alternative.Dry lab techniques,especially virtual and augmented reality,make up 78%of current dry lab research,whereas wet labs still set the standard for anatomical realism.AIM To evaluate the effectiveness,limitations,and future directions of wet and dry lab simulation in orthopaedic training.METHODS A scoping review was carried out across four databases-PubMed,Cochrane Library,Web of Science,and EBSCOhost-up to 2025.Medical Subject Headings included:"Orthopaedic Education","Wet Lab","Dry Lab","Simulation Training","Virtual Reality",and"Surgical Procedure".Eligible studies focused on orthopaedic or spinal surgical education,employed wet or dry lab techniques,and assessed training effectiveness.Exclusion criteria consisted of non-English publications,abstracts only,non-orthopaedic research,and studies unrelated to simulation.Two reviewers independently screened titles,abstracts,and full texts,resolving discrepancies with a third reviewer.RESULTS From 1851 records,101 studies met inclusion:78 on dry labs,7 on wet labs,4 on both.Virtual reality(VR)simulations were most common,with AI increasingly used for feedback and assessment.Cadaveric training remains the gold standard for accuracy and tactile feedback,while dry labs-especially VR-offer scalability,lower cost(40%-60%savings in five studies),and accessibility for novices.Senior residents prefer wet labs for complex tasks;juniors favour dry labs for basics.Challenges include limited transferability data,lack of standard outcome metrics,and ethical concerns about cadaver use and AI assessment.CONCLUSION Wet and dry labs each have unique strengths in orthopaedic training.A hybrid approach combining both,supported by standardised assessments and outcome studies,is most effective.Future efforts should aim for uniform reporting,integrating new technologies,and policy support for hybrid curricula to enhance skills and patient care.
基金supported by the National Key R&D Program of China[grant number 2023YFC3008004]。
文摘This study introduces a new ocean surface friction velocity scheme and a modified Thompson cloud microphysics parameterization scheme into the CMA-TYM model.The impact of these two parameterization schemes on the prediction of the movement track and intensity of Typhoon Kompasu in 2021 is examined.Additionally,the possible reasons for their effects on tropical cyclone(TC)intensity prediction are analyzed.Statistical results show that both parameterization schemes improve the predictions of Typhoon Kompasu’s track and intensity.The influence on track prediction becomes evident after 60 h of model integration,while the significant positive impact on intensity prediction is observed after 66 h.Further analysis reveals that these two schemes affect the timing and magnitude of extreme TC intensity values by influencing the evolution of the TC’s warm-core structure.
基金financially supported by the National Key Research and Development Program of China (2022YFB3706802)。
文摘Automation and intelligence have become the primary trends in the design of investment casting processes.However,the design of gating and riser systems still lacks precise quantitative evaluation criteria.Numerical simulation plays a significant role in quantitatively evaluating current processes and making targeted improvements,but its limitations lie in the inability to dynamically reflect the formation outcomes of castings under varying process conditions,making real-time adjustments to gating and riser designs challenging.In this study,an automated design model for gating and riser systems based on integrated parametric 3D modeling-simulation framework is proposed,which enhances the flexibility and usability of evaluating the casting process by simulation.Firstly,geometric feature extraction technology is employed to obtain the geometric information of the target casting.Based on this information,an automated design framework for gating and riser systems is established,incorporating multiple structural parameters for real-time process control.Subsequently,the simulation results for various structural parameters are analyzed,and the influence of these parameters on casting formation is thoroughly investigated.Finally,the optimal design scheme is generated and validated through experimental verification.Simulation analysis and experimental results show that using a larger gate neck(24 mm in side length) and external risers promotes a more uniform temperature distribution and a more stable flow state,effectively eliminating shrinkage cavities and enhancing process yield by 15%.
基金Supported by the National Natural Science Foundation of China under Grant No.51975138the High-Tech Ship Scientific Research Project from the Ministry of Industry and Information Technology under Grant No.CJ05N20the National Defense Basic Research Project under Grant No.JCKY2023604C006.
文摘Marine thin plates are susceptible to welding deformation owing to their low structural stiffness.Therefore,the efficient and accurate prediction of welding deformation is essential for improving welding quality.The traditional thermal elastic-plastic finite element method(TEP-FEM)can accurately predict welding deformation.However,its efficiency is low because of the complex nonlinear transient computation,making it difficult to meet the needs of rapid engineering evaluation.To address this challenge,this study proposes an efficient prediction method for welding deformation in marine thin plate butt welds.This method is based on the coupled temperature gradient-thermal strain method(TG-TSM)that integrates inherent strain theory with a shell element finite element model.The proposed method first extracts the distribution pattern and characteristic value of welding-induced inherent strain through TEP-FEM analysis.This strain is then converted into the equivalent thermal load applied to the shell element model for rapid computation.The proposed method-particularly,the gradual temperature gradient-thermal strain method(GTG-TSM)-achieved improved computational efficiency and consistent precision.Furthermore,the proposed method required much less computation time than the traditional TEP-FEM.Thus,this study lays the foundation for future prediction of welding deformation in more complex marine thin plates.
基金supported by the National Natural Science Foundation of China (Grant No.11574244 for G.Y.G.)the XJTU Research Fund for AI Science (Grant No.2025YXYC011 for G.Y.G.)the Hong Kong Global STEM Professorship Scheme (for X.C.Z.)。
文摘Compared to the well-studied two-dimensional(2D)ferroelectricity,the appearance of 2D antiferroelectricity is much rarer,where local dipoles from the nonequivalent sublattices within 2D monolayers are oppositely oriented.Using NbOCl_(2) monolayer with competing ferroelectric(FE)and antiferroelectric(AFE)phases as a 2D material platform,we demonstrate the emergence of intrinsic antiferroelectricity in NbOCl_(2) monolayer under experimentally accessible shear strain,along with new functionality associated with electric field-induced AFE-to-FE phase transition.Specifically,the complex configuration space accommodating FE and AFE phases,polarization switching kinetics,and finite temperature thermodynamic properties of 2D NbOCl_(2) are all accurately predicted by large-scale molecular dynamics simulations based on deep learning interatomic potential model.Moreover,room temperature stable antiferroelectricity with low polarization switching barrier and one-dimensional collinear polarization arrangement is predicted in shear-deformed NbOCl_(2) monolayer.The transition from AFE to FE phase in 2D NbOCl_(2) can be triggered by a low critical electric field,leading to a double polarization–electric(P–E)loop with small hysteresis.A new type of optoelectronic device composed of AFE-NbOCl_(2) is proposed,enabling electric“writing”and nonlinear optical“reading”logical operation with fast operation speed and low power consumption.
文摘Analysis of the environmental and economic performance of fishing vessels has received limited attention compared with other ship types despite their notable contribution to global greenhouse gas(GHG)emissions.This study evaluates the carbon footprint(CF)and economic viability of a liquefied natural gas(LNG)-fueled fishing vessel,using real engine operation simulations to provide precise and dynamic evaluation of fuel consumption and GHG emissions.Operational profiles are obtained through the utilization of onboard monitoring systems,whereas engine performance is simulated using the 1D/0D AVL Boost^(TM)model.Life cycle assessment(LCA)is conducted to quantify the environmental impact,whereas life cycle cost assessment(LCCA)is performed to analyze the profitability of LNG as an alternative fuel.The potential impact of the future fuel price uncertainties is addressed using Monte Carlo simulations.The LCA findings indicate that LNG has the potential to reduce the CF of the vessel by 14%to 16%,in comparison to a diesel power system configuration that serves as the baseline scenario.The LCCA results further indicate that the total cost of an LNG-powered ship is lower by 9.5%-13.8%,depending on the share of LNG and pilot fuels.This finding highlights the potential of LNG to produce considerable environmental benefits while addressing economic challenges under diverse operational and fuel price conditions.
基金supported by the National Natural Science Foundation of China (Grant Nos. 61003082,60921062,61005077)
文摘Spike neural networks are inspired by animal brains,and outperform traditional neural networks on complicated tasks.However,spike neural networks are usually used on a large scale,and they cannot be computed on commercial,off-the-shelf computers.A parallel architecture is proposed and developed for discrete-event simulations of spike neural networks.Furthermore,mechanisms for both parallelism degree estimation and dynamic load balance are emphasized with theoretical and computational analysis.Simulation results show the effectiveness of the proposed parallelized spike neural network system and its corresponding support components.
基金CRC MiningThe University of Queensland for their financial support for this study
文摘Data collected from truck payload management systems at various surface mines shows that the payload variance is significant and must be considered in analysing the mine productivity,energy consumption,greenhouse gas emissions and associated cost.Payload variance causes significant differences in gross vehicle weights.Heavily loaded trucks travel slower up ramps than lightly loaded trucks.Faster trucks are slowed by the presence of slower trucks,resulting in‘bunching’,production losses and increasing fuel consumptions.This paper simulates the truck bunching phenomena in large surface mines to improve truck and shovel systems’efficiency and minimise fuel consumption.The study concentrated on completing a practical simulation model based on a discrete event method which is most commonly used in this field of research in other industries.The simulation model has been validated by a dataset collected from a large surface mine in Arizona state,USA.The results have shown that there is a good agreement between the actual and estimated values of investigated parameters.
