The accurate identification of delay time in millisecond blasting plays an important role in the optimization of blasting design and reduction of vibration effect. Through a case study of a surge shaft blasting projec...The accurate identification of delay time in millisecond blasting plays an important role in the optimization of blasting design and reduction of vibration effect. Through a case study of a surge shaft blasting project, the capability of the EMD （empirical mode decomposition） method in identifying the delay time of short millisecond blasting with precise initiation was compared with the instantaneous energy method based on Hilbert-Huang transform （HHT）. The recognition rate of the EMD method was more than 80%, while the instantaneous energy method was less than 25%. By analyzing the instantaneous energy of single-hole blasting signal, it was found that the instantaneous energy method was adaptable to millisecond blasting with delay time longer than half of the energy peak period. The EMD method was used to identify delay time of millisecond blasting in Zijinshan open-pit mine. According to the identification results, the blasting parameters were optimized for controlling the blast-induced vibration and reducing the large block ratio. The field data showed that the velocity peak of ground vibration was reduced by more than 30%under almost the same maximum charge per delay by the optimization of delay time and detonating detonators. Combining with slag-remaining blasting and burden optimization of the first row, the large block ratio was reduced to less than 3%. The research results proved that the identification method based on HHT was feasible to optimize the blasting design. The identification method is also of certain reference value for design optimization of other similar blasting projects.展开更多
In order to prevent and control the spread of rumors, the implementation of immunization strategies for ignorant individuals is very necessary, where the immunization usually means letting them learn the truth of rumo...In order to prevent and control the spread of rumors, the implementation of immunization strategies for ignorant individuals is very necessary, where the immunization usually means letting them learn the truth of rumors.Considering the facts that there is always a delay time between rumor spreading and implementing immunization, and that the truth of rumors can also be spread out, this paper constructs a novel susceptible-infected-removed(SIR) model.The propagation dynamical behaviors of the SIR model on homogeneous networks are investigated by using the meanfield theory and the Monte Carlo method. Research shows that the greater the delay time, the worse the immune effect of the immunization strategy. It is also found that the spread of the truth can inhibit to some extent the propagation of rumors, and the trend will become more obvious with the increase of reliability of the truth. Moreover, under the influence of delay time, the existence of nodes' identification force still slightly reduces the propagation degree of rumors.展开更多
The mean first-passage time of a bistable system with time-delayed feedback driven by multiplicative non-Gaussian noise and additive Gaussian white noise is investigated. Firstly, the non-Markov process is reduced to ...The mean first-passage time of a bistable system with time-delayed feedback driven by multiplicative non-Gaussian noise and additive Gaussian white noise is investigated. Firstly, the non-Markov process is reduced to the Markov process through a path-integral approach; Secondly, the approximate Fokker-Planck equation is obtained by applying the unified coloured noise approximation, the small time delay approximation and the Novikov Theorem. The functional analysis and simplification are employed to obtain the approximate expressions of MFPT. The effects of non-Gaussian parameter （measures deviation from Gaussian character） r, the delay time τ, the noise correlation time to, the intensities D and a of noise on the MFPT are discussed. It is found that the escape time could be reduced by increasing the delay time τ, the noise correlation time τ0, or by reducing the intensities D and α. As far as we know, this is the first time to consider the effect of delay time on the mean first-passage time in the stochastic dynamical system.展开更多
A periodic inspection policy for a single component system based on a three-stage failure process is proposed, and two different kinds of failures covering "hard" and "human" are considered in the ...A periodic inspection policy for a single component system based on a three-stage failure process is proposed, and two different kinds of failures covering "hard" and "human" are considered in the proposed policy.The system is periodically inspected and inspections are perfect so that they can identify the intended defect.If the severe defect is detected by an inspection, an immediate repair is needed. However, once the system is identified to be in the minor defective state, there are two options. The first is to do nothing till the arrival of identifying the severe defect or hard failure, and the second is to repair immediately. Repair for any defect can renew the system with a limited probability such that the system may fail after repair due to human errors, which is common in many industrial applications. Two models are constructed by minimizing the expected cost per unit time and compared. We provide a numerical example to demonstrate the proposed model.展开更多
Effects of the speed relaxation time on the optimal velocity car-following model (OVM) with delay time due to driver reaction time proposed by Bando et al.(1995) were studied by numerical methods. Results showed that ...Effects of the speed relaxation time on the optimal velocity car-following model (OVM) with delay time due to driver reaction time proposed by Bando et al.(1995) were studied by numerical methods. Results showed that the OVM including the delay is not physically sensitive to the speed relaxation times. A modified car-following model is proposed to overcome the deficiency. Analyses of the linear stability of the modified model were conducted. It is shown that coexisting flows appear if the initial homogeneous headway of the traffic flow is between critical values. In addition, phase transitions occur on varying the initially homogeneous headway.展开更多
The effects of nanosecond discharge on ignition characteristics of a stoichiometric methane–air mixture without inert diluent gas were studied by numerical simulation at 0.1 MPa and an initial temperature of 1300 K. ...The effects of nanosecond discharge on ignition characteristics of a stoichiometric methane–air mixture without inert diluent gas were studied by numerical simulation at 0.1 MPa and an initial temperature of 1300 K. A modified non-equilibrium plasma kinetic model was developed to simulate the temporal evolution of particles produced during nanosecond discharge and its afterglow. As important roles in ignition, path fluxes of O and H radicals were analyzed in detail. Different strength of E/N and different discharge duration were applied to the discharge process in this study. And the results presented that a deposited energy of 1–30 m J·cm^(-3) could dramatically reduce the ignition delay time. Furthermore, temperature and radicals analysis was conducted to investigate the effect of non-equilibrium plasma on production of intermediate radicals. Finally, sensitivity analysis was employed to have further understanding on ignition chemistries of the mixture under nanosecond discharge.展开更多
The navigation software uses the positioning system to determine the traffic conditions of the road sections in advance,so as to predict the travel time of the road sections.However,in the case of traffic congestion,t...The navigation software uses the positioning system to determine the traffic conditions of the road sections in advance,so as to predict the travel time of the road sections.However,in the case of traffic congestion,the accuracy of its prediction time is low.After empirical analysis,this paper establishes a multi-factor synthesis by studying 7 factors:traffic flow,number of stops,traffic light duration,road network density,average speed,road area,and number of intersections the prediction function achieves the purpose of accurately predicting the transit time of congested road sections.The gray correlation coefficients of the seven factors obtained from the gray correlation analysis are:0.9827,0.9679,0.6747,0.8030,0.9445,0.8759,0.4328.The correlation coefficients of traffic volume,number of stops,average speed,and road congestion delay time were all about 95%,which were the main influencing factors of the study.The prediction needs to be based on functions.This paper fits the main influencing factors to the delay time of congested roads.It is found that the delay time varies parabolically with the traffic flow and the number of stops,and linearly with the average speed.Because the three impact factors have different weights on the delay time of congested roads,demand takes the weight of each factor.Therefore,the gray correlation coefficients occupied by the main influencing factors are normalized to obtain the weights of three of 0.340,0.334,and 0.326.The weighted fitting function is subjected to nonlinear summation processing to obtain a multi-factor comprehensive prediction function.By comparing the original data with the fitting data and calculating the accuracy of the fitting function,it is found that the accuracy of each fitting function is close to 0,the residual error,the relative error is small,and the accuracy is high.展开更多
A new accurate calculation method of electric power harmonic parameters was presented. Based on the delay time theorem of Fourier transform, the frequency of the electric power was calculated, and then, suing interpol...A new accurate calculation method of electric power harmonic parameters was presented. Based on the delay time theorem of Fourier transform, the frequency of the electric power was calculated, and then, suing interpolation in the frequency domain of the windows, the parameters （amplitude and phase） of each harmonic frequency signals were calculated accurately. In the paper, the effect of the delay time and the windows on the electric power harmonic calculation accuracy was analysed. The digital simulation and the physical measurement tests show that the proposed method is effective and has more advantages than other methods which are based on multipoint interpolation especially in calculation time cost; therefore, it is very suitable to be used in the single chip DSP micro-processor.展开更多
The integrated optical true time delay phased array antenna system has the advantages of high bandwidth,small size,low loss and strong antiinterference capability,etc.The high integration of the optically controlled p...The integrated optical true time delay phased array antenna system has the advantages of high bandwidth,small size,low loss and strong antiinterference capability,etc.The high integration of the optically controlled phased array antenna system is a necessary trend for the future development of the phased array,and it is also a major focus and difficulty in the current research of integrated microwave photonics.This paper firstly introduces the basic principle and development history of optical true time delay phased array antenna system based on microwave photonics,and briefly introduces the main implementation methods and integration platform of optical true time delay.Then,the application and development prospect of optical true time delay technology in beam control of phased array antenna system are mainly presented.Finally,according to the current research progress,the possible research directions of integrated optically controlled phased array antenna systems in the future are proposed.展开更多
In this paper,a pair of dynamic high-gain observer and output feedback controller is proposed for nonlinear systems with multiple unknown time delays.By constructing Lyapunov-Krasovskii functionals,it shows that globa...In this paper,a pair of dynamic high-gain observer and output feedback controller is proposed for nonlinear systems with multiple unknown time delays.By constructing Lyapunov-Krasovskii functionals,it shows that global state asymptotic regulation can be ensured by introducing a single dynamic gain;furthermore,global asymptotic stabilization can be achieved by choosing a sufficiently large static scaling gain when the upper bounds of all system parameters are known.Especially,the output coefficient is allowed to be non-differentiable with unknown upper bound.This paper proposes a generalized Lyapunov matrix inequality based dynamic-gain scaling method,which significantly simplifies the design computational complexity by comparing with the classic backstepping method.展开更多
We experimentally analyze the effect of the optical power on the time delay signature identification and the random bit generation in chaotic semiconductor laser with optical feedback.Due to the inevitable noise durin...We experimentally analyze the effect of the optical power on the time delay signature identification and the random bit generation in chaotic semiconductor laser with optical feedback.Due to the inevitable noise during the photoelectric detection and analog-digital conversion,the varying of output optical power would change the signal to noise ratio,then impact time delay signature identification and the random bit generation.Our results show that,when the optical power is less than-14 dBm,with the decreasing of the optical power,the actual identified time delay signature degrades and the entropy of the chaotic signal increases.Moreover,the extracted random bit sequence with lower optical power is more easily pass through the randomness testing.展开更多
This paper studies the bandgap characteristics of a locally resonant metamaterial beam with time delays.The dispersion relations are addressed based on transfer matrix method.The governing equations of motion of the b...This paper studies the bandgap characteristics of a locally resonant metamaterial beam with time delays.The dispersion relations are addressed based on transfer matrix method.The governing equations of motion of the beam in the frequency domain are given according to spectral element method.The amplitude-frequency responses of the forced beam are determined by solving linear algebraic equations.The obtained results show that the time-delayed feedback control has great relationships with the location,width and number of the bandgaps.It is interesting that the time delay can change the direction of the movement of the bandgap and give rise to the generation of multiple bandgaps.The influences of different combinations of control parameters on the bandgap properties are shown,such as broadening effects.展开更多
This paper studies global stabilization via predictor-based sampled-data output feedback for a class of feedforward nonlinear time-delay systems.Note that the traditional sampled-data observer via zero-order holder ma...This paper studies global stabilization via predictor-based sampled-data output feedback for a class of feedforward nonlinear time-delay systems.Note that the traditional sampled-data observer via zero-order holder may result in the performance degradation of the observer.In this paper,an improved predictor-based observer is designed to compensate for the influence of the unmeasurable states,sampling errors and output delay.In addition,a sampled-data output-feedback controller is also constructed using the gain scaling technique.By the Lyapunov-Krasovskii functional method,the global exponential stability of the resulting closed-loop system can be guaranteed under some sufficient conditions.The simulation results are provided to demonstrate the main results.展开更多
Incorporating asymmetric quadratic and cubic stiffnesses into a time-delayed Duffing oscillator provides a more accurate representation of practical systems,where the resulting nonlinearities critically influence subh...Incorporating asymmetric quadratic and cubic stiffnesses into a time-delayed Duffing oscillator provides a more accurate representation of practical systems,where the resulting nonlinearities critically influence subharmonic resonance phenomena,yet comprehensive investigations remain limited.This study employs the generalized harmonic balance(HB)method to conduct an analytical investigation of the subharmonic resonance behavior in asymmetric stiffness nonlinear systems with time delay.To further examine the switching behavior between primary and subharmonic resonances,a numerical continuation approach combining the shooting method and the parameter continuation algorithm is developed.The analytical and numerical continuation solutions are validated through direct numerical integration.Subsequently,the switching behavior and associated bifurcation points are analyzed by means of the numerical continuation results in conjunction with the Floquet theory.Finally,the effects of delay parameters on the existence range of subharmonic responses are discussed in detail,and the influence of initial conditions on system dynamics is explored with basin of attraction plots.This work establishes a comprehensive framework for the analytical and numerical study on time-delayed nonlinear systems with asymmetric stiffness,providing valuable theoretical insights into the stability management of such dynamic systems.展开更多
The accuracy of conventional time delay estimation （TDE） algorithms is limited by the sampling interval. A novel algorithm of subsample TDE suitable for widehand signals is presented to improve the accuracy. This al...The accuracy of conventional time delay estimation （TDE） algorithms is limited by the sampling interval. A novel algorithm of subsample TDE suitable for widehand signals is presented to improve the accuracy. This algorithm applies periodogram and parabolic interpolation to the cross correlation spectrum of band limited stochastic signals, and can obtain a continuous time delay estimator. Simulations are carried out to compare the performance of the proposed algorithm with that of other subsample TDE algorithms. Results show that the proposed algorithm outperforms other algorithms and reachs the Cramer-Rao lower bound （CRLB） at a high signal- to-noise ratio. For the wideband characteristic and the randomness of the transmitting signal, the proposed algo- rithm is suitable for the low probability of intercept radars.展开更多
A neural network Smith predictive control strategy is proposed to deal with inpu t and feedback time delays in telerobot systems. The delay time is assumed to b e invariant and unknown. The proposed control structure...A neural network Smith predictive control strategy is proposed to deal with inpu t and feedback time delays in telerobot systems. The delay time is assumed to b e invariant and unknown. The proposed control structure consists of a slave syst em and a master controller. In the slave system, a recurrent neural network (RNN ) with on-line weight tuning algorithm is employed to approximate the dynamics of the time-delay-free nonlinear plant, which is used to linearize the slave s ystem. The master controller is a Smith predictor for the linearized slave syste m, which provides prediction and maintains the desirable tracking performance. S tability propriety is guaranteed based on the Lyapunov method. A simulation of a two-link robotic manipulator is provided to illustrate the effectiveness of th e proposed control strategy.展开更多
Purpose–This research paper aims to investigate the effects of gradual deployment of market penetration rates(MPR)of connected vehicles(MPR of CVs)on delay time and fuel consumption.Design/methodology/approach–A rea...Purpose–This research paper aims to investigate the effects of gradual deployment of market penetration rates(MPR)of connected vehicles(MPR of CVs)on delay time and fuel consumption.Design/methodology/approach–A real-world origin-destination demand matrix survey was conducted in Boston,MA to identify the number of peak hour passing vehicles in the case study.Findings–The results showed that as the number of CVs(MPR)in the network increases,the total delay time decreases by an average of 14%and the fuel consumption decreases by an average of 56%,respectively,from scenarios 3 to 15 compared to scenario 2.Research limitations/implications–The first limitation of this study was considering a small network.The considered network shows a small part of the case study.Originality/value–This study can be a milestone for future research regarding gradual deployment of CVs’effects on transport networks.Efficient policy(s)may define based on the results of this network for Brockton transport network.展开更多
A new algorithm is proposed for computing the embedding dimension and delay time in phase space reconstruction.It makes use of the zero of the nonbias multiple autocorrelation function of the chaotic time series to de...A new algorithm is proposed for computing the embedding dimension and delay time in phase space reconstruction.It makes use of the zero of the nonbias multiple autocorrelation function of the chaotic time series to determine the time delay,which efficiently depresses the computing error caused by tracing arbitrarily the slop variation of average displacement(AD)in AD algorithm.Thereafter,by means of the iterative algorithm of multiple autocorrelation andΓtest,the near-optimum parameters of embedding dimension and delay time are estimated.This algorithm is provided with a sound theoretic basis,and its computing complexity is relatively lower and not strongly dependent on the data length.The simulated experimental results indicate that the relative error of the correlation dimension of standard chaotic time series is decreased from 4.4%when using conventional algorithm to 1.06%when using this algorithm.The accuracy of invariants in phase space reconstruction is greatly improved.展开更多
By establishing equivalent fixed point theorem, the boundary value problems of p Laplace equations with finite time delay are studied. It’s the first time that the functional differential equation is discussed w...By establishing equivalent fixed point theorem, the boundary value problems of p Laplace equations with finite time delay are studied. It’s the first time that the functional differential equation is discussed with p Laplacian. The topological degree and fixed point theorem on cone are used to prove the existence of solution and positive solution. The conditions are all easy to check.展开更多
A delay time was observed for both W/O inversion to O/W and the opposite inversion process. The delay time decreased with increasing stirring speed. For O/W inversion to W/O, the delay time was very sensitive to the o...A delay time was observed for both W/O inversion to O/W and the opposite inversion process. The delay time decreased with increasing stirring speed. For O/W inversion to W/O, the delay time was very sensitive to the oil volume fraction and the initial stirring speed. Increased oil volume fraction and increased initial stirring speed both reduced the delay time. Inversion from W/O to O/W was a gradual process. But inversion from O/W to W/O had two stages: the preparation stage and the phase inversion stage. The time needed in the first stage was the delay time.展开更多
基金Project(2013BAB02B05)supported by the National 12th Five-Year Science and Technology Supporting Plan of ChinaProject(2015CX005)supported by the Innovation Driven Plan of Central South University of ChinaProject(2016zzts094)supported by the Fundamental Research Funds for the Central Universities of Central South University,China
文摘The accurate identification of delay time in millisecond blasting plays an important role in the optimization of blasting design and reduction of vibration effect. Through a case study of a surge shaft blasting project, the capability of the EMD （empirical mode decomposition） method in identifying the delay time of short millisecond blasting with precise initiation was compared with the instantaneous energy method based on Hilbert-Huang transform （HHT）. The recognition rate of the EMD method was more than 80%, while the instantaneous energy method was less than 25%. By analyzing the instantaneous energy of single-hole blasting signal, it was found that the instantaneous energy method was adaptable to millisecond blasting with delay time longer than half of the energy peak period. The EMD method was used to identify delay time of millisecond blasting in Zijinshan open-pit mine. According to the identification results, the blasting parameters were optimized for controlling the blast-induced vibration and reducing the large block ratio. The field data showed that the velocity peak of ground vibration was reduced by more than 30%under almost the same maximum charge per delay by the optimization of delay time and detonating detonators. Combining with slag-remaining blasting and burden optimization of the first row, the large block ratio was reduced to less than 3%. The research results proved that the identification method based on HHT was feasible to optimize the blasting design. The identification method is also of certain reference value for design optimization of other similar blasting projects.
基金Supported by the National Natural Science Foundation of China under Grant No.61402531the Natural Science Basic Research Plan in Shaanxi Province of China under Grant Nos.2014JQ8358,2015JQ6231,and 2014JQ8307+1 种基金the China Postdoctoral Science Foundation under Grant No.2015M582910the Basic Research Foundation of Engineering University of the Chinese People’s Armed Police Force under Grant Nos.WJY201419,WJY201605 and JLX201686
文摘In order to prevent and control the spread of rumors, the implementation of immunization strategies for ignorant individuals is very necessary, where the immunization usually means letting them learn the truth of rumors.Considering the facts that there is always a delay time between rumor spreading and implementing immunization, and that the truth of rumors can also be spread out, this paper constructs a novel susceptible-infected-removed(SIR) model.The propagation dynamical behaviors of the SIR model on homogeneous networks are investigated by using the meanfield theory and the Monte Carlo method. Research shows that the greater the delay time, the worse the immune effect of the immunization strategy. It is also found that the spread of the truth can inhibit to some extent the propagation of rumors, and the trend will become more obvious with the increase of reliability of the truth. Moreover, under the influence of delay time, the existence of nodes' identification force still slightly reduces the propagation degree of rumors.
基金National Natural Science Foundation of China under Grant Nos.10472091,10332030,and 10502042
文摘The mean first-passage time of a bistable system with time-delayed feedback driven by multiplicative non-Gaussian noise and additive Gaussian white noise is investigated. Firstly, the non-Markov process is reduced to the Markov process through a path-integral approach; Secondly, the approximate Fokker-Planck equation is obtained by applying the unified coloured noise approximation, the small time delay approximation and the Novikov Theorem. The functional analysis and simplification are employed to obtain the approximate expressions of MFPT. The effects of non-Gaussian parameter （measures deviation from Gaussian character） r, the delay time τ, the noise correlation time to, the intensities D and a of noise on the MFPT are discussed. It is found that the escape time could be reduced by increasing the delay time τ, the noise correlation time τ0, or by reducing the intensities D and α. As far as we know, this is the first time to consider the effect of delay time on the mean first-passage time in the stochastic dynamical system.
基金the National Natural Science Foundation of China(Nos.71701038 and 71601019)the Ministry of Education Humanities and Social Sciences Planning Fund(No.16YJC630174)+1 种基金the Fundamental Research Funds for the Central Universities of China(No.N172304017)the Hebei Province High School Science and Technology Research Project(No.QN2017104)
文摘A periodic inspection policy for a single component system based on a three-stage failure process is proposed, and two different kinds of failures covering "hard" and "human" are considered in the proposed policy.The system is periodically inspected and inspections are perfect so that they can identify the intended defect.If the severe defect is detected by an inspection, an immediate repair is needed. However, once the system is identified to be in the minor defective state, there are two options. The first is to do nothing till the arrival of identifying the severe defect or hard failure, and the second is to repair immediately. Repair for any defect can renew the system with a limited probability such that the system may fail after repair due to human errors, which is common in many industrial applications. Two models are constructed by minimizing the expected cost per unit time and compared. We provide a numerical example to demonstrate the proposed model.
基金Project (No. G1998030408) supported by the National Basic Re-search Program (973) of China
文摘Effects of the speed relaxation time on the optimal velocity car-following model (OVM) with delay time due to driver reaction time proposed by Bando et al.(1995) were studied by numerical methods. Results showed that the OVM including the delay is not physically sensitive to the speed relaxation times. A modified car-following model is proposed to overcome the deficiency. Analyses of the linear stability of the modified model were conducted. It is shown that coexisting flows appear if the initial homogeneous headway of the traffic flow is between critical values. In addition, phase transitions occur on varying the initially homogeneous headway.
基金Supported by the National Natural Science Foundation of China(No.51376021)the Fundamental Research Funds for the Central Universities(No.2015YJS146)
文摘The effects of nanosecond discharge on ignition characteristics of a stoichiometric methane–air mixture without inert diluent gas were studied by numerical simulation at 0.1 MPa and an initial temperature of 1300 K. A modified non-equilibrium plasma kinetic model was developed to simulate the temporal evolution of particles produced during nanosecond discharge and its afterglow. As important roles in ignition, path fluxes of O and H radicals were analyzed in detail. Different strength of E/N and different discharge duration were applied to the discharge process in this study. And the results presented that a deposited energy of 1–30 m J·cm^(-3) could dramatically reduce the ignition delay time. Furthermore, temperature and radicals analysis was conducted to investigate the effect of non-equilibrium plasma on production of intermediate radicals. Finally, sensitivity analysis was employed to have further understanding on ignition chemistries of the mixture under nanosecond discharge.
文摘The navigation software uses the positioning system to determine the traffic conditions of the road sections in advance,so as to predict the travel time of the road sections.However,in the case of traffic congestion,the accuracy of its prediction time is low.After empirical analysis,this paper establishes a multi-factor synthesis by studying 7 factors:traffic flow,number of stops,traffic light duration,road network density,average speed,road area,and number of intersections the prediction function achieves the purpose of accurately predicting the transit time of congested road sections.The gray correlation coefficients of the seven factors obtained from the gray correlation analysis are:0.9827,0.9679,0.6747,0.8030,0.9445,0.8759,0.4328.The correlation coefficients of traffic volume,number of stops,average speed,and road congestion delay time were all about 95%,which were the main influencing factors of the study.The prediction needs to be based on functions.This paper fits the main influencing factors to the delay time of congested roads.It is found that the delay time varies parabolically with the traffic flow and the number of stops,and linearly with the average speed.Because the three impact factors have different weights on the delay time of congested roads,demand takes the weight of each factor.Therefore,the gray correlation coefficients occupied by the main influencing factors are normalized to obtain the weights of three of 0.340,0.334,and 0.326.The weighted fitting function is subjected to nonlinear summation processing to obtain a multi-factor comprehensive prediction function.By comparing the original data with the fitting data and calculating the accuracy of the fitting function,it is found that the accuracy of each fitting function is close to 0,the residual error,the relative error is small,and the accuracy is high.
文摘A new accurate calculation method of electric power harmonic parameters was presented. Based on the delay time theorem of Fourier transform, the frequency of the electric power was calculated, and then, suing interpolation in the frequency domain of the windows, the parameters （amplitude and phase） of each harmonic frequency signals were calculated accurately. In the paper, the effect of the delay time and the windows on the electric power harmonic calculation accuracy was analysed. The digital simulation and the physical measurement tests show that the proposed method is effective and has more advantages than other methods which are based on multipoint interpolation especially in calculation time cost; therefore, it is very suitable to be used in the single chip DSP micro-processor.
基金supported by Fund of State Key Laboratory of IPOC(BUPT)(No.IPOC2021ZT16),China.
文摘The integrated optical true time delay phased array antenna system has the advantages of high bandwidth,small size,low loss and strong antiinterference capability,etc.The high integration of the optically controlled phased array antenna system is a necessary trend for the future development of the phased array,and it is also a major focus and difficulty in the current research of integrated microwave photonics.This paper firstly introduces the basic principle and development history of optical true time delay phased array antenna system based on microwave photonics,and briefly introduces the main implementation methods and integration platform of optical true time delay.Then,the application and development prospect of optical true time delay technology in beam control of phased array antenna system are mainly presented.Finally,according to the current research progress,the possible research directions of integrated optically controlled phased array antenna systems in the future are proposed.
基金supported by the Zhejiang Provincial Natural Science Foundation(LY24F030011,LY23F030005)the National Natural Science Foundation of China(62373131).
文摘In this paper,a pair of dynamic high-gain observer and output feedback controller is proposed for nonlinear systems with multiple unknown time delays.By constructing Lyapunov-Krasovskii functionals,it shows that global state asymptotic regulation can be ensured by introducing a single dynamic gain;furthermore,global asymptotic stabilization can be achieved by choosing a sufficiently large static scaling gain when the upper bounds of all system parameters are known.Especially,the output coefficient is allowed to be non-differentiable with unknown upper bound.This paper proposes a generalized Lyapunov matrix inequality based dynamic-gain scaling method,which significantly simplifies the design computational complexity by comparing with the classic backstepping method.
基金Project supported in part by the National Natural Science Foundation of China(Grant Nos.62005129 and 62175116)。
文摘We experimentally analyze the effect of the optical power on the time delay signature identification and the random bit generation in chaotic semiconductor laser with optical feedback.Due to the inevitable noise during the photoelectric detection and analog-digital conversion,the varying of output optical power would change the signal to noise ratio,then impact time delay signature identification and the random bit generation.Our results show that,when the optical power is less than-14 dBm,with the decreasing of the optical power,the actual identified time delay signature degrades and the entropy of the chaotic signal increases.Moreover,the extracted random bit sequence with lower optical power is more easily pass through the randomness testing.
文摘This paper studies the bandgap characteristics of a locally resonant metamaterial beam with time delays.The dispersion relations are addressed based on transfer matrix method.The governing equations of motion of the beam in the frequency domain are given according to spectral element method.The amplitude-frequency responses of the forced beam are determined by solving linear algebraic equations.The obtained results show that the time-delayed feedback control has great relationships with the location,width and number of the bandgaps.It is interesting that the time delay can change the direction of the movement of the bandgap and give rise to the generation of multiple bandgaps.The influences of different combinations of control parameters on the bandgap properties are shown,such as broadening effects.
基金supported by the Autonomous Innovation Team Foundation for“20 Items of the New University”of Jinan City(202228087)the National Natural Science Foundation of China(62073190).
文摘This paper studies global stabilization via predictor-based sampled-data output feedback for a class of feedforward nonlinear time-delay systems.Note that the traditional sampled-data observer via zero-order holder may result in the performance degradation of the observer.In this paper,an improved predictor-based observer is designed to compensate for the influence of the unmeasurable states,sampling errors and output delay.In addition,a sampled-data output-feedback controller is also constructed using the gain scaling technique.By the Lyapunov-Krasovskii functional method,the global exponential stability of the resulting closed-loop system can be guaranteed under some sufficient conditions.The simulation results are provided to demonstrate the main results.
基金Project supported by the National Natural Science Foundation of China(Nos.U24B2062,520754285247051087)+1 种基金the Two-chain Fusion High-end Machine Tool Project of Shaanxi Province of China(No.2021LLRh-01-02)the Youth Fund of the National Natural Science Foundation of China(No.52205281)。
文摘Incorporating asymmetric quadratic and cubic stiffnesses into a time-delayed Duffing oscillator provides a more accurate representation of practical systems,where the resulting nonlinearities critically influence subharmonic resonance phenomena,yet comprehensive investigations remain limited.This study employs the generalized harmonic balance(HB)method to conduct an analytical investigation of the subharmonic resonance behavior in asymmetric stiffness nonlinear systems with time delay.To further examine the switching behavior between primary and subharmonic resonances,a numerical continuation approach combining the shooting method and the parameter continuation algorithm is developed.The analytical and numerical continuation solutions are validated through direct numerical integration.Subsequently,the switching behavior and associated bifurcation points are analyzed by means of the numerical continuation results in conjunction with the Floquet theory.Finally,the effects of delay parameters on the existence range of subharmonic responses are discussed in detail,and the influence of initial conditions on system dynamics is explored with basin of attraction plots.This work establishes a comprehensive framework for the analytical and numerical study on time-delayed nonlinear systems with asymmetric stiffness,providing valuable theoretical insights into the stability management of such dynamic systems.
基金Supported by the National Mobile Communications Research Laboratory Foundation (N200902)~~
文摘The accuracy of conventional time delay estimation （TDE） algorithms is limited by the sampling interval. A novel algorithm of subsample TDE suitable for widehand signals is presented to improve the accuracy. This algorithm applies periodogram and parabolic interpolation to the cross correlation spectrum of band limited stochastic signals, and can obtain a continuous time delay estimator. Simulations are carried out to compare the performance of the proposed algorithm with that of other subsample TDE algorithms. Results show that the proposed algorithm outperforms other algorithms and reachs the Cramer-Rao lower bound （CRLB） at a high signal- to-noise ratio. For the wideband characteristic and the randomness of the transmitting signal, the proposed algo- rithm is suitable for the low probability of intercept radars.
文摘A neural network Smith predictive control strategy is proposed to deal with inpu t and feedback time delays in telerobot systems. The delay time is assumed to b e invariant and unknown. The proposed control structure consists of a slave syst em and a master controller. In the slave system, a recurrent neural network (RNN ) with on-line weight tuning algorithm is employed to approximate the dynamics of the time-delay-free nonlinear plant, which is used to linearize the slave s ystem. The master controller is a Smith predictor for the linearized slave syste m, which provides prediction and maintains the desirable tracking performance. S tability propriety is guaranteed based on the Lyapunov method. A simulation of a two-link robotic manipulator is provided to illustrate the effectiveness of th e proposed control strategy.
文摘Purpose–This research paper aims to investigate the effects of gradual deployment of market penetration rates(MPR)of connected vehicles(MPR of CVs)on delay time and fuel consumption.Design/methodology/approach–A real-world origin-destination demand matrix survey was conducted in Boston,MA to identify the number of peak hour passing vehicles in the case study.Findings–The results showed that as the number of CVs(MPR)in the network increases,the total delay time decreases by an average of 14%and the fuel consumption decreases by an average of 56%,respectively,from scenarios 3 to 15 compared to scenario 2.Research limitations/implications–The first limitation of this study was considering a small network.The considered network shows a small part of the case study.Originality/value–This study can be a milestone for future research regarding gradual deployment of CVs’effects on transport networks.Efficient policy(s)may define based on the results of this network for Brockton transport network.
文摘A new algorithm is proposed for computing the embedding dimension and delay time in phase space reconstruction.It makes use of the zero of the nonbias multiple autocorrelation function of the chaotic time series to determine the time delay,which efficiently depresses the computing error caused by tracing arbitrarily the slop variation of average displacement(AD)in AD algorithm.Thereafter,by means of the iterative algorithm of multiple autocorrelation andΓtest,the near-optimum parameters of embedding dimension and delay time are estimated.This algorithm is provided with a sound theoretic basis,and its computing complexity is relatively lower and not strongly dependent on the data length.The simulated experimental results indicate that the relative error of the correlation dimension of standard chaotic time series is decreased from 4.4%when using conventional algorithm to 1.06%when using this algorithm.The accuracy of invariants in phase space reconstruction is greatly improved.
文摘By establishing equivalent fixed point theorem, the boundary value problems of p Laplace equations with finite time delay are studied. It’s the first time that the functional differential equation is discussed with p Laplacian. The topological degree and fixed point theorem on cone are used to prove the existence of solution and positive solution. The conditions are all easy to check.
基金the 34th International U NESCO Coursefor Advanced Research in Chemistry and Chem icalEngineeringand the National Natural
文摘A delay time was observed for both W/O inversion to O/W and the opposite inversion process. The delay time decreased with increasing stirring speed. For O/W inversion to W/O, the delay time was very sensitive to the oil volume fraction and the initial stirring speed. Increased oil volume fraction and increased initial stirring speed both reduced the delay time. Inversion from W/O to O/W was a gradual process. But inversion from O/W to W/O had two stages: the preparation stage and the phase inversion stage. The time needed in the first stage was the delay time.
