Continuous thermo-mechanical processing (CTMP) of 6201 aluminum alloy was simulated on Gleeble-1500. The deformed specimens were analyzed by the observation of TEM and the measurement of hardness. It was shown that r...Continuous thermo-mechanical processing (CTMP) of 6201 aluminum alloy was simulated on Gleeble-1500. The deformed specimens were analyzed by the observation of TEM and the measurement of hardness. It was shown that rapid solid solution and aging treatment can be effectively combined in one procedure by the strain induced during CTMP. The deformation temperature is ranging from 540* C to 300* C, the hardness increases directly before the 6th pass followed by a slight drop, the amount of precipitates increases with the holding time after deformation. Uniformly distributed and stabilized Mg2Si precipitates, as well as dislocation substructure can be observed on deformed specimens which have been subsequently held at 300℃ for 60 seconds.展开更多
Continuous material processing operations like printing and textiles manufacturing are conducted under highly variable conditions due to changes in the environment and/or in the materials being processed.As such,the p...Continuous material processing operations like printing and textiles manufacturing are conducted under highly variable conditions due to changes in the environment and/or in the materials being processed.As such,the processing parameters require robust real-time adjustment appropriate to the conditions of a nonlinear system.This paper addresses this issue by presenting a hybrid feedforward-feedback nonlinear model predictive controller for continuous material processing operations.The adaptive feedback control strategy of the controller augments the standard feedforward control to ensure improved robustness and compensation for environmental disturbances and/or parameter uncertainties.Thus,the controller can reduce the need for manual adjustments.The controller applies nonlinear generalized predictive control to generate an adaptive control signal for attaining robust performance.A wavelet-based neural network model is adopted as the prediction model with high prediction precision and time-frequency localization characteristics.Online training is utilized to predict uncertain system dynamics by tuning the wavelet neural network parameters and the controller parameters adaptively.The performance of the controller algorithm is verified by both simulation,and in a real-time practical application involving a single-input single-output double-zone sliver drafting system used in textiles manufacturing.Both the simulation and practical results demonstrate an excellent control performance in terms of the mean thickness and coefficient of variation of output slivers,which verifies the effectiveness of this approach in improving the long-term uniformity of slivers.展开更多
A new process for swirling flow generation in the submerged entry nozzle （SEN） in continuous casting process of steel was proposed. A rotating electromagnetic field was set up around the SEN to induce swirling flow ...A new process for swirling flow generation in the submerged entry nozzle （SEN） in continuous casting process of steel was proposed. A rotating electromagnetic field was set up around the SEN to induce swirling flow by Lorentz force. The flow and temperature fields in the SEN and round billet mold with electromagnetic swirling were numerically simulated and then verified by the electromagnetic swirling model experiment of low melting point alloy. The effects of divergent angle of the SEN on the flow and temperature fields in mold with electromagnetic swirling were investigated. The electromagnetic swirling flow generator （EMSFG） could effectively induce swirling flow of molten steel in the SEN, which consequently improved greatly the flow and temperature fields in the mold. Below the nozzle outlet in mold, with the increase of divergent angle, the stream of bulk flow diverged more widely, the high temperature zone shifted up, and the temperature field became more uniform. Above the nozzle outlet in mold, with 350 A electromagnetic swirling, when the divergent angle of the SEN increased, the upward flow velocity and the meniscus temperature first increased and then decreased. With a divergent angle of 60~, the upward flow velocity and meniscus temperature reaced the largest value.展开更多
A pilot-scale apparatus for continuous supercritical and near-critical water reaction was set up. A high-pressure slurry supplying system was developed to feed the solid material-water slurries. The apparatus features...A pilot-scale apparatus for continuous supercritical and near-critical water reaction was set up. A high-pressure slurry supplying system was developed to feed the solid material-water slurries. The apparatus features temperature up to 600℃, pressure up to 40MPa, residence time from 24s to 15min, maximum amount of slurry supply of 2.4 L·h-1, maximum solid content of slurry up to 10%(by mass) for cellulose from Merck, and resistance to corrosion. Long-time runs of decomposition of cellulose were carried out and steady runs were confirmed. Kinetics of cellulose decomposition was studied. The apparent activation energy evaluated was 147kJ·mol-1. In addition, a new three-step pathway for cellulose hydrolysis was proposed. The derived kinetic equation is in good agreement with the experimental data.展开更多
In this paper, a novel near-net-shape forming process, continuous semisolid extrusion process （CSEP） of AZ31 alloy was proposed, and the dynamical solidification behaviors and metal flow during the process were firs...In this paper, a novel near-net-shape forming process, continuous semisolid extrusion process （CSEP） of AZ31 alloy was proposed, and the dynamical solidification behaviors and metal flow during the process were firstly investigated. During casting AZ31 alloy by this process, non-uniform microstructure distributions and non- equilibrium solidification region near the roll surface were found in the roll-shoe gap. Microstructural evolution from dendrite to rosette and spherical grains was observed during the casting by CSEP. Casting temperature, roll-shoe gap width and cooling ability have great effect on casting process and metal flow, so these factors should be carefully controlled, a proper casting temperature of 710-750℃ is suggested. The white α phases were strongly stretched during the processing, and the remnant liquids are correspondingly distributes along the solid phase boundaries and also show stripped lines.展开更多
An iterative learning model predictive control （ILMPC） technique is applied to a class of continuous/batch processes. Such processes are characterized by the operations of batch processes generating periodic strong ...An iterative learning model predictive control （ILMPC） technique is applied to a class of continuous/batch processes. Such processes are characterized by the operations of batch processes generating periodic strong disturbances to the continuous processes and traditional regulatory controllers are unable to eliminate these periodic disturbances. ILMPC integrates the feature of iterative learning control （ILC） handling repetitive signal and the flexibility of model predictive control （MPC）. By on-line monitoring the operation status of batch processes, an event-driven iterative learning algorithm for batch repetitive disturbances is initiated and the soft constraints are adjusted timely as the feasible region is away from the desired operating zone. The results of an industrial application show that the proposed ILMPC method is effective for a class of continuous/batch processes.展开更多
The models, algorithms and implementation results of a computerized scheduling system were introduced for the steelmaking-continuous casting process （SCCP） of a steel plant in China. The scheduling of SCCP in this p...The models, algorithms and implementation results of a computerized scheduling system were introduced for the steelmaking-continuous casting process （SCCP） of a steel plant in China. The scheduling of SCCP in this plant required that each cast plan should be processed on time, the charges in the same cast should be processed con- tinuously on the same caster, and the waiting time of the charges which are in front of each caster cannot exceed the given threshold. At the same time, the processing time of charges cannot be conflicted mutually in the same convert- ers or refining furnaces. Based on the research background, a hybrid optimal scheduling approach and its application were discussed. Aiming at the main equipment scheduling, an optimal scheduling method was proposed which con- sisted of equipment assignment algorithm based on dynamic program （DP） technique and conflict elimination algo rithm based on linear program （LP） technique. The approach guarantees that the charges are continuously processed on the same caster. Meanwhile, the requirement for high temperature ladle can also be satisfied due to the ladle matching function. Numerical results demonstrate solution quality, computational efficiency, and values of the mod els and algorithm.展开更多
Sliding gate control system is widely employed in continuous casting process of steel to control flow rate of molten steel.As molten steel passes through a sliding gate,uneven flow develops.This will cause asymmetrica...Sliding gate control system is widely employed in continuous casting process of steel to control flow rate of molten steel.As molten steel passes through a sliding gate,uneven flow develops.This will cause asymmetrical distribution of flow and temperature field in mold consequently,formation of vortex near the nozzle and entrapment of CC powder into the molten steel.etc,which have negative effect on process productivity and product quality.To suppress the uneven flow,electromagnetic swirling flow has been proposed to impose on the flow in submerged entry nozzle below the sliding gate.In this study the uneven flow developed by incompletely open sliding gate and the suppression of this uneven flow using electromagnetic swirling flow are numerically studied in round billet continuous casting of steel process.The improvement of the flow and temperature filed in the submerged entry nozzle and mold are investigated.It is found that:The uneven velocity in nozzle can be suppressed by electromagnetic swirling flow,and the flow and temperature field in mold be improved obviously;With the increase of electromagnetic swirling intensity,the effect of uneven flow can be almost completely suppressed.展开更多
Combined with the technological characteristics of thin slab continuous rolling process （TSCR）, dynamic recrystallization of an extremely coarse austenite of low carbon steel is studied by Thermecmaster-Z hot simula...Combined with the technological characteristics of thin slab continuous rolling process （TSCR）, dynamic recrystallization of an extremely coarse austenite of low carbon steel is studied by Thermecmaster-Z hot simulator. By the analysis of true stress-strain curves and the observation of microstructures at different deformation stages, the critical stress and critical strain are determined under different deformation conditions. The effect of Z parameter on dynamic recrystallization of coarse austenite is studied. The microstructure evolution in real production is also discussed.展开更多
Air guns are important sources for marine seismic exploration. Far-field wavelet of air gun arrays, as a necessary parameter for pre-stack processing and source models, plays an important role during marine seismic da...Air guns are important sources for marine seismic exploration. Far-field wavelet of air gun arrays, as a necessary parameter for pre-stack processing and source models, plays an important role during marine seismic data processing and interpretation. When an air gun fires, it generates a series of air bubbles. Similar to onshore seismic exploration, the water forms a plastic fluid near the bubble; the farther the air gun is located from the measurement, the more steady and more accurately represented the wavelet will be. In practice, hydrophones should be placed more than 100 m from the air gun; however, traditional seismic cables cannot meet this requirement. On the other hand, vertical cables provide a viable solution to this problem. This study uses a vertical cable to receive wavelets from 38 air guns and data are collected offshore Southeast Qiong, where the water depth is over 1000 m. In this study, the wavelets measured using this technique coincide very well with the simulated wavelets and can therefore represent the real shape of the wavelets. This experiment fills a technology gap in China.展开更多
Swirling flow in a submerged entry nozzle is effective on improving quality of casting block and casting speed in continuous casting of steel.A new method for swirling flow generation in the nozzle has been proposed b...Swirling flow in a submerged entry nozzle is effective on improving quality of casting block and casting speed in continuous casting of steel.A new method for swirling flow generation in the nozzle has been proposed by the authors,that is a rotating electromagnetic field is set up around a submerged entry nozzle(SEN)to induce swirling flow in it by Lorentz force.In this study,the magnetic field in molten steel in the submerged entry nozzle,the flow and temperature field in the SEN and mold in round,square billet and slab continuous casting process of steel are numerically studied.The model experiment of electromagnetic swirling continuous casting is also conducted with low melting point alloy.The commercial test for slab is undergoing.Results by numerical simulation and experiment show that the swirling flow by the optimum designed electromagnetic swirling generator can not only improve the distribution of flow and temperature in mold but also achieve the same effects generated by the swirling blade process. And,more effects on continuous casting process can be expected after this electromagnetic swirling process is optimized.展开更多
The continuous affinity- recycle extraction (CARE) process is extended ic a system with ultrafiltration membranes. The mathematical model of the process is established by taking into account membrane rejections to th...The continuous affinity- recycle extraction (CARE) process is extended ic a system with ultrafiltration membranes. The mathematical model of the process is established by taking into account membrane rejections to the components in a crude mixture. The process performance, defined as concentration factor (CF ), purification factor (PF ) and recovery yield (REC), is analyzed by computer simulations. The results show that CF and REC increase, but PF decreases with the membrane rejection. It is likely that optimum operating conditions exist to give the best process performance because the increases in eluant and affinity-recycle flow rate improve REC but decrease PF.展开更多
A plate＇s internal quality is very critical, especially for boilers and high-pressure vessels. The ultrasonic test （UT） is the main type of non-destructive flaw detection for heavy plates, which is important becaus...A plate＇s internal quality is very critical, especially for boilers and high-pressure vessels. The ultrasonic test （UT） is the main type of non-destructive flaw detection for heavy plates, which is important because one of the main reasons for plate defects is ultrasonic flaws. This study, based on Baosteel＇ s practical experience in the manufacture of heavy plates, elucidates the cause of defect formation by analyzing ultrasonic flaw testing maps and using special equipment, such as the scanning electron microscope, electron probe and the optical microscope. The author puts forward the following improvement measures： ① Ultrasonic flaws are caused by central porosity and segregation,[H] bubbles and inclusion in slabs.②Ultrasonic flaws are more likely to occur in the bottom and top of slabs rather than the other positions in the casting sequence. It is clear that one-quarter of the inner camber＇ s thickness is accumulated inclusion.③It is clear that overheating in the tundish and the flow of the casting mould have an effect on ultrasonic flaws caused by inclusions.④Soft reduction improves central porosity and segregation,which decreases the number of ultrasonic flaws in the plate.展开更多
Performance of continuous 1-butanol production process by Clostridium bacteria is complicated by alternation of acidogenic and solventogenic phases during fermentation what correlates with culture growth and sporulati...Performance of continuous 1-butanol production process by Clostridium bacteria is complicated by alternation of acidogenic and solventogenic phases during fermentation what correlates with culture growth and sporulation, respectively. However, the strain Clostridium pasteurianum NRRL B598 showed diverse pattern of solvents production when butanol production started during exponential growth phase in batch cultivation. If cultivated under glucose limited conditions with dilution rate 0.03 hl, constant product concentration was almost achieved. By contrast, glucose non-limited continuous experiment operated with dilution rate 0.07 h-1 lead to mutually adverse oscillations of product and glucose concentrations. Regarding the process economy, glucose limited continuous cultivation seems to be superior due to utilization of total supplied glucose amount, advantageous butanol/acetone ratio and higher butanol yield.展开更多
China’s foreign trade from January to August According to Customs figures,China’s total import and export in August reached 2.04 trillion yuan,down 9.7%year on year(the same below).Export was 1.2 trillion yuan,down ...China’s foreign trade from January to August According to Customs figures,China’s total import and export in August reached 2.04 trillion yuan,down 9.7%year on year(the same below).Export was 1.2 trillion yuan,down 6.1%,and import 0.84 trillion yuan,down 14.3%.Trade surplus was 368 billion yuan,an increase of 20.1%.In terms of the U.S.dollar,the total import and export in August reached US$333.5 billion,展开更多
Pyrene solution and distilled water were flowed through a microreactor at a predetermined flow rate to generate pyrene crystals. Pyrene nanocrystals were crystallized by a Continuous Flow Microreactor. The particle si...Pyrene solution and distilled water were flowed through a microreactor at a predetermined flow rate to generate pyrene crystals. Pyrene nanocrystals were crystallized by a Continuous Flow Microreactor. The particle size and luminescence properties of pyrene nanocrystals produced were evaluated. The crystal mean size between 60 nm and 400 nm could be controlled by the operating conditions. The crystal mean size decreased with increasing flow rate and solution concentration. In addition, the crystal morphology also changed. In the case of slow flow conditions, a needle-like crystal morphology was obtained. The crystal morphology became spherical on increasing the flow rate. Pyrene crystals with size about 400 nm exhibited luminescence at about 470 nm. As the crystal size decreased, the intensity of the luminescence also declined. The luminescence wavelength was in the range of about 370 to 400 nm.展开更多
In this article, we summarize some results on invariant non-homogeneous and dynamic-equilibrium (DE) continuous Markov stochastic processes. Moreover, we discuss a few examples and consider a new application of DE pro...In this article, we summarize some results on invariant non-homogeneous and dynamic-equilibrium (DE) continuous Markov stochastic processes. Moreover, we discuss a few examples and consider a new application of DE processes to elements of survival analysis. These elements concern the stochastic quadratic-hazard-rate model, for which our work 1) generalizes the reading of its It? stochastic ordinary differential equation (ISODE) for the hazard-rate-driving independent (HRDI) variables, 2) specifies key properties of the hazard-rate function, and in particular, reveals that the baseline value of the HRDI variables is the expectation of the DE solution of the ISODE, 3) suggests practical settings for obtaining multi-dimensional probability densities necessary for consistent and systematic reconstruction of missing data by Gibbs sampling and 4) further develops the corresponding line of modeling. The resulting advantages are emphasized in connection with the framework of clinical trials of chronic obstructive pulmonary disease (COPD) where we propose the use of an endpoint reflecting the narrowing of airways. This endpoint is based on a fairly compact geometric model that quantifies the course of the obstruction, shows how it is associated with the hazard rate, and clarifies why it is life-threatening. The work also suggests a few directions for future research.展开更多
Objective: to analyze the effect of continuous midwifery nursing and routine nursing on vaginal trial labor. Methods: the sample size was 90 cases, all of which were pregnant women with scar uterus. They were randomly...Objective: to analyze the effect of continuous midwifery nursing and routine nursing on vaginal trial labor. Methods: the sample size was 90 cases, all of which were pregnant women with scar uterus. They were randomly divided into control group and observation group. Routine intervention was applied in the control group, and continuous midwifery intervention was applied in the whole process of observation group. Results: observation group were significantly better, P < 0.05. Conclusion: the whole process of continuous midwifery nursing effect is better.展开更多
We study the Nadaraya-Watson estimators for the drift function of two-sided reflected stochastic differential equations.The estimates,based on either the continuously observed process or the discretely observed proces...We study the Nadaraya-Watson estimators for the drift function of two-sided reflected stochastic differential equations.The estimates,based on either the continuously observed process or the discretely observed process,are considered.Under certain conditions,we prove the strong consistency and the asymptotic normality of the two estimators.Our method is also suitable for one-sided reflected stochastic differential equations.Simulation results demonstrate that the performance of our estimator is superior to that of the estimator proposed by Cholaquidis et al.(Stat Sin,2021,31:29-51).Several real data sets of the currency exchange rate are used to illustrate our proposed methodology.展开更多
Coating with viscous formulations has been essential in numerous industries as it can be a means for providing functionalization, additional properties, as well as other benefits. However, there have been scarce studi...Coating with viscous formulations has been essential in numerous industries as it can be a means for providing functionalization, additional properties, as well as other benefits. However, there have been scarce studies that have investigated and proposed methodologies in literature. Continuous coating of powders with viscous liquids poses as a promising technology, which has been mentioned in some studies, but has not yet been thoroughly investigated. This paper employs the use of image processing and analysis, in combination with statistical analysis of particles to evaluate the effectiveness of foams and liquids as a means of coating powder beds. Two different sizes of twin screw mixers that are working in continuous operation are employed, and a new continuous foaming device is fabricated and used for the experiments of coating. The effect of materials and process parameters (as for example rotational speed, and flowrate) on the quality of coating are investigated. Image analysis is used to assess the coating quality. The results clearly showcase the potential of using twin screw mixers for coating purposes and not only for mixing. The hypothesis that using large bubble foams to improve the coating of viscous liquids on particles is proven correct, as they provide higher quality coatings compared to their equivalent liquids, when used in the twin screw mixer. Surprisingly, using a larger scale twin screw mixer, does not show a substantial effect on the mixing, regarding quality, however there is still a requirement for mix optimization for achieving scale-up of this process. These results provide a new pathway for coating powders with viscous formulations in industrial applications, requiring less energy and effort in this process, and can pave the way towards introducing more sustainable industrial methodologies for coating.展开更多
文摘Continuous thermo-mechanical processing (CTMP) of 6201 aluminum alloy was simulated on Gleeble-1500. The deformed specimens were analyzed by the observation of TEM and the measurement of hardness. It was shown that rapid solid solution and aging treatment can be effectively combined in one procedure by the strain induced during CTMP. The deformation temperature is ranging from 540* C to 300* C, the hardness increases directly before the 6th pass followed by a slight drop, the amount of precipitates increases with the holding time after deformation. Uniformly distributed and stabilized Mg2Si precipitates, as well as dislocation substructure can be observed on deformed specimens which have been subsequently held at 300℃ for 60 seconds.
文摘Continuous material processing operations like printing and textiles manufacturing are conducted under highly variable conditions due to changes in the environment and/or in the materials being processed.As such,the processing parameters require robust real-time adjustment appropriate to the conditions of a nonlinear system.This paper addresses this issue by presenting a hybrid feedforward-feedback nonlinear model predictive controller for continuous material processing operations.The adaptive feedback control strategy of the controller augments the standard feedforward control to ensure improved robustness and compensation for environmental disturbances and/or parameter uncertainties.Thus,the controller can reduce the need for manual adjustments.The controller applies nonlinear generalized predictive control to generate an adaptive control signal for attaining robust performance.A wavelet-based neural network model is adopted as the prediction model with high prediction precision and time-frequency localization characteristics.Online training is utilized to predict uncertain system dynamics by tuning the wavelet neural network parameters and the controller parameters adaptively.The performance of the controller algorithm is verified by both simulation,and in a real-time practical application involving a single-input single-output double-zone sliver drafting system used in textiles manufacturing.Both the simulation and practical results demonstrate an excellent control performance in terms of the mean thickness and coefficient of variation of output slivers,which verifies the effectiveness of this approach in improving the long-term uniformity of slivers.
基金Item Sponsored by Fundamental Research Funds for Central Universities of China(N100409010)Project for Key Laboratory of Liaoning Province of China(LS2010065)"111 Project"of Northeastern University of China(B07015)
文摘A new process for swirling flow generation in the submerged entry nozzle （SEN） in continuous casting process of steel was proposed. A rotating electromagnetic field was set up around the SEN to induce swirling flow by Lorentz force. The flow and temperature fields in the SEN and round billet mold with electromagnetic swirling were numerically simulated and then verified by the electromagnetic swirling model experiment of low melting point alloy. The effects of divergent angle of the SEN on the flow and temperature fields in mold with electromagnetic swirling were investigated. The electromagnetic swirling flow generator （EMSFG） could effectively induce swirling flow of molten steel in the SEN, which consequently improved greatly the flow and temperature fields in the mold. Below the nozzle outlet in mold, with the increase of divergent angle, the stream of bulk flow diverged more widely, the high temperature zone shifted up, and the temperature field became more uniform. Above the nozzle outlet in mold, with 350 A electromagnetic swirling, when the divergent angle of the SEN increased, the upward flow velocity and the meniscus temperature first increased and then decreased. With a divergent angle of 60~, the upward flow velocity and meniscus temperature reaced the largest value.
基金Partly supported by Research for Future Program"Integrated field 5,causes and effects of environmental loading and its reduction",the Japan Society for the Promotion of Science(JSPS).
文摘A pilot-scale apparatus for continuous supercritical and near-critical water reaction was set up. A high-pressure slurry supplying system was developed to feed the solid material-water slurries. The apparatus features temperature up to 600℃, pressure up to 40MPa, residence time from 24s to 15min, maximum amount of slurry supply of 2.4 L·h-1, maximum solid content of slurry up to 10%(by mass) for cellulose from Merck, and resistance to corrosion. Long-time runs of decomposition of cellulose were carried out and steady runs were confirmed. Kinetics of cellulose decomposition was studied. The apparent activation energy evaluated was 147kJ·mol-1. In addition, a new three-step pathway for cellulose hydrolysis was proposed. The derived kinetic equation is in good agreement with the experimental data.
基金supports from National High-Tech R&D Program of China (GrantNo. 2007AA03Z111)Natural Science Foundation of China (Grant No. 50604007)the Program for New Century Excellent Talents in University (Grant No.NCET-06-0285 and NCET-08-0097)
文摘In this paper, a novel near-net-shape forming process, continuous semisolid extrusion process （CSEP） of AZ31 alloy was proposed, and the dynamical solidification behaviors and metal flow during the process were firstly investigated. During casting AZ31 alloy by this process, non-uniform microstructure distributions and non- equilibrium solidification region near the roll surface were found in the roll-shoe gap. Microstructural evolution from dendrite to rosette and spherical grains was observed during the casting by CSEP. Casting temperature, roll-shoe gap width and cooling ability have great effect on casting process and metal flow, so these factors should be carefully controlled, a proper casting temperature of 710-750℃ is suggested. The white α phases were strongly stretched during the processing, and the remnant liquids are correspondingly distributes along the solid phase boundaries and also show stripped lines.
基金Supported by the National Creative Research Groups Science Foundation of China （60721062） and the National High Technology Research and Development Program of China （2007AA04Z162）.
文摘An iterative learning model predictive control （ILMPC） technique is applied to a class of continuous/batch processes. Such processes are characterized by the operations of batch processes generating periodic strong disturbances to the continuous processes and traditional regulatory controllers are unable to eliminate these periodic disturbances. ILMPC integrates the feature of iterative learning control （ILC） handling repetitive signal and the flexibility of model predictive control （MPC）. By on-line monitoring the operation status of batch processes, an event-driven iterative learning algorithm for batch repetitive disturbances is initiated and the soft constraints are adjusted timely as the feasible region is away from the desired operating zone. The results of an industrial application show that the proposed ILMPC method is effective for a class of continuous/batch processes.
基金Item Sponsored by National Natural Science Foundation of China(61174187,71021061,60974091,61104174)Startup Fund of Northeastern University of China(29321006)Basic Scientific Research Foundation of Northeast University of China(N110208001)
文摘The models, algorithms and implementation results of a computerized scheduling system were introduced for the steelmaking-continuous casting process （SCCP） of a steel plant in China. The scheduling of SCCP in this plant required that each cast plan should be processed on time, the charges in the same cast should be processed con- tinuously on the same caster, and the waiting time of the charges which are in front of each caster cannot exceed the given threshold. At the same time, the processing time of charges cannot be conflicted mutually in the same convert- ers or refining furnaces. Based on the research background, a hybrid optimal scheduling approach and its application were discussed. Aiming at the main equipment scheduling, an optimal scheduling method was proposed which con- sisted of equipment assignment algorithm based on dynamic program （DP） technique and conflict elimination algo rithm based on linear program （LP） technique. The approach guarantees that the charges are continuously processed on the same caster. Meanwhile, the requirement for high temperature ladle can also be satisfied due to the ladle matching function. Numerical results demonstrate solution quality, computational efficiency, and values of the mod els and algorithm.
基金Item Sponsored by The Central Universities(N100409010)Project for Key Laboratory of Liaoning Province(LS2010065)"111 project" of Northeastern University,China(B07015)
文摘Sliding gate control system is widely employed in continuous casting process of steel to control flow rate of molten steel.As molten steel passes through a sliding gate,uneven flow develops.This will cause asymmetrical distribution of flow and temperature field in mold consequently,formation of vortex near the nozzle and entrapment of CC powder into the molten steel.etc,which have negative effect on process productivity and product quality.To suppress the uneven flow,electromagnetic swirling flow has been proposed to impose on the flow in submerged entry nozzle below the sliding gate.In this study the uneven flow developed by incompletely open sliding gate and the suppression of this uneven flow using electromagnetic swirling flow are numerically studied in round billet continuous casting of steel process.The improvement of the flow and temperature filed in the submerged entry nozzle and mold are investigated.It is found that:The uneven velocity in nozzle can be suppressed by electromagnetic swirling flow,and the flow and temperature field in mold be improved obviously;With the increase of electromagnetic swirling intensity,the effect of uneven flow can be almost completely suppressed.
文摘Combined with the technological characteristics of thin slab continuous rolling process （TSCR）, dynamic recrystallization of an extremely coarse austenite of low carbon steel is studied by Thermecmaster-Z hot simulator. By the analysis of true stress-strain curves and the observation of microstructures at different deformation stages, the critical stress and critical strain are determined under different deformation conditions. The effect of Z parameter on dynamic recrystallization of coarse austenite is studied. The microstructure evolution in real production is also discussed.
基金supported by the National Natural Science Foundation of China (Nos. 41304096, 41230318)National High-tech R&D Program of China (863 Program) (No. 2013AA0925010201)+1 种基金Foundation of Ministry of Education of China (No. 20130132120014)the Fundamental Research Funds for the Central Universities (Nos. 1313017, 1362013)
文摘Air guns are important sources for marine seismic exploration. Far-field wavelet of air gun arrays, as a necessary parameter for pre-stack processing and source models, plays an important role during marine seismic data processing and interpretation. When an air gun fires, it generates a series of air bubbles. Similar to onshore seismic exploration, the water forms a plastic fluid near the bubble; the farther the air gun is located from the measurement, the more steady and more accurately represented the wavelet will be. In practice, hydrophones should be placed more than 100 m from the air gun; however, traditional seismic cables cannot meet this requirement. On the other hand, vertical cables provide a viable solution to this problem. This study uses a vertical cable to receive wavelets from 38 air guns and data are collected offshore Southeast Qiong, where the water depth is over 1000 m. In this study, the wavelets measured using this technique coincide very well with the simulated wavelets and can therefore represent the real shape of the wavelets. This experiment fills a technology gap in China.
基金Item Sponsored by Central Universities(N100409010)Project for Key Laboratory of Liaoning Province(LS2010065)"111 project" of Northeastern University,China(B07015)
文摘Swirling flow in a submerged entry nozzle is effective on improving quality of casting block and casting speed in continuous casting of steel.A new method for swirling flow generation in the nozzle has been proposed by the authors,that is a rotating electromagnetic field is set up around a submerged entry nozzle(SEN)to induce swirling flow in it by Lorentz force.In this study,the magnetic field in molten steel in the submerged entry nozzle,the flow and temperature field in the SEN and mold in round,square billet and slab continuous casting process of steel are numerically studied.The model experiment of electromagnetic swirling continuous casting is also conducted with low melting point alloy.The commercial test for slab is undergoing.Results by numerical simulation and experiment show that the swirling flow by the optimum designed electromagnetic swirling generator can not only improve the distribution of flow and temperature in mold but also achieve the same effects generated by the swirling blade process. And,more effects on continuous casting process can be expected after this electromagnetic swirling process is optimized.
文摘The continuous affinity- recycle extraction (CARE) process is extended ic a system with ultrafiltration membranes. The mathematical model of the process is established by taking into account membrane rejections to the components in a crude mixture. The process performance, defined as concentration factor (CF ), purification factor (PF ) and recovery yield (REC), is analyzed by computer simulations. The results show that CF and REC increase, but PF decreases with the membrane rejection. It is likely that optimum operating conditions exist to give the best process performance because the increases in eluant and affinity-recycle flow rate improve REC but decrease PF.
文摘A plate＇s internal quality is very critical, especially for boilers and high-pressure vessels. The ultrasonic test （UT） is the main type of non-destructive flaw detection for heavy plates, which is important because one of the main reasons for plate defects is ultrasonic flaws. This study, based on Baosteel＇ s practical experience in the manufacture of heavy plates, elucidates the cause of defect formation by analyzing ultrasonic flaw testing maps and using special equipment, such as the scanning electron microscope, electron probe and the optical microscope. The author puts forward the following improvement measures： ① Ultrasonic flaws are caused by central porosity and segregation,[H] bubbles and inclusion in slabs.②Ultrasonic flaws are more likely to occur in the bottom and top of slabs rather than the other positions in the casting sequence. It is clear that one-quarter of the inner camber＇ s thickness is accumulated inclusion.③It is clear that overheating in the tundish and the flow of the casting mould have an effect on ultrasonic flaws caused by inclusions.④Soft reduction improves central porosity and segregation,which decreases the number of ultrasonic flaws in the plate.
文摘Performance of continuous 1-butanol production process by Clostridium bacteria is complicated by alternation of acidogenic and solventogenic phases during fermentation what correlates with culture growth and sporulation, respectively. However, the strain Clostridium pasteurianum NRRL B598 showed diverse pattern of solvents production when butanol production started during exponential growth phase in batch cultivation. If cultivated under glucose limited conditions with dilution rate 0.03 hl, constant product concentration was almost achieved. By contrast, glucose non-limited continuous experiment operated with dilution rate 0.07 h-1 lead to mutually adverse oscillations of product and glucose concentrations. Regarding the process economy, glucose limited continuous cultivation seems to be superior due to utilization of total supplied glucose amount, advantageous butanol/acetone ratio and higher butanol yield.
文摘China’s foreign trade from January to August According to Customs figures,China’s total import and export in August reached 2.04 trillion yuan,down 9.7%year on year(the same below).Export was 1.2 trillion yuan,down 6.1%,and import 0.84 trillion yuan,down 14.3%.Trade surplus was 368 billion yuan,an increase of 20.1%.In terms of the U.S.dollar,the total import and export in August reached US$333.5 billion,
文摘Pyrene solution and distilled water were flowed through a microreactor at a predetermined flow rate to generate pyrene crystals. Pyrene nanocrystals were crystallized by a Continuous Flow Microreactor. The particle size and luminescence properties of pyrene nanocrystals produced were evaluated. The crystal mean size between 60 nm and 400 nm could be controlled by the operating conditions. The crystal mean size decreased with increasing flow rate and solution concentration. In addition, the crystal morphology also changed. In the case of slow flow conditions, a needle-like crystal morphology was obtained. The crystal morphology became spherical on increasing the flow rate. Pyrene crystals with size about 400 nm exhibited luminescence at about 470 nm. As the crystal size decreased, the intensity of the luminescence also declined. The luminescence wavelength was in the range of about 370 to 400 nm.
文摘In this article, we summarize some results on invariant non-homogeneous and dynamic-equilibrium (DE) continuous Markov stochastic processes. Moreover, we discuss a few examples and consider a new application of DE processes to elements of survival analysis. These elements concern the stochastic quadratic-hazard-rate model, for which our work 1) generalizes the reading of its It? stochastic ordinary differential equation (ISODE) for the hazard-rate-driving independent (HRDI) variables, 2) specifies key properties of the hazard-rate function, and in particular, reveals that the baseline value of the HRDI variables is the expectation of the DE solution of the ISODE, 3) suggests practical settings for obtaining multi-dimensional probability densities necessary for consistent and systematic reconstruction of missing data by Gibbs sampling and 4) further develops the corresponding line of modeling. The resulting advantages are emphasized in connection with the framework of clinical trials of chronic obstructive pulmonary disease (COPD) where we propose the use of an endpoint reflecting the narrowing of airways. This endpoint is based on a fairly compact geometric model that quantifies the course of the obstruction, shows how it is associated with the hazard rate, and clarifies why it is life-threatening. The work also suggests a few directions for future research.
文摘Objective: to analyze the effect of continuous midwifery nursing and routine nursing on vaginal trial labor. Methods: the sample size was 90 cases, all of which were pregnant women with scar uterus. They were randomly divided into control group and observation group. Routine intervention was applied in the control group, and continuous midwifery intervention was applied in the whole process of observation group. Results: observation group were significantly better, P < 0.05. Conclusion: the whole process of continuous midwifery nursing effect is better.
基金partially supported by the National Natural Science Foundation of China(11871244)the Fundamental Research Funds for the Central Universities,JLU。
文摘We study the Nadaraya-Watson estimators for the drift function of two-sided reflected stochastic differential equations.The estimates,based on either the continuously observed process or the discretely observed process,are considered.Under certain conditions,we prove the strong consistency and the asymptotic normality of the two estimators.Our method is also suitable for one-sided reflected stochastic differential equations.Simulation results demonstrate that the performance of our estimator is superior to that of the estimator proposed by Cholaquidis et al.(Stat Sin,2021,31:29-51).Several real data sets of the currency exchange rate are used to illustrate our proposed methodology.
文摘Coating with viscous formulations has been essential in numerous industries as it can be a means for providing functionalization, additional properties, as well as other benefits. However, there have been scarce studies that have investigated and proposed methodologies in literature. Continuous coating of powders with viscous liquids poses as a promising technology, which has been mentioned in some studies, but has not yet been thoroughly investigated. This paper employs the use of image processing and analysis, in combination with statistical analysis of particles to evaluate the effectiveness of foams and liquids as a means of coating powder beds. Two different sizes of twin screw mixers that are working in continuous operation are employed, and a new continuous foaming device is fabricated and used for the experiments of coating. The effect of materials and process parameters (as for example rotational speed, and flowrate) on the quality of coating are investigated. Image analysis is used to assess the coating quality. The results clearly showcase the potential of using twin screw mixers for coating purposes and not only for mixing. The hypothesis that using large bubble foams to improve the coating of viscous liquids on particles is proven correct, as they provide higher quality coatings compared to their equivalent liquids, when used in the twin screw mixer. Surprisingly, using a larger scale twin screw mixer, does not show a substantial effect on the mixing, regarding quality, however there is still a requirement for mix optimization for achieving scale-up of this process. These results provide a new pathway for coating powders with viscous formulations in industrial applications, requiring less energy and effort in this process, and can pave the way towards introducing more sustainable industrial methodologies for coating.
