Electrically controlled solid propellant(ECSP)offers multiple ignition and adjustable burning rate,serving as fuel for next-generation intelligent propulsion systems.To further enhance the combustion performance of EC...Electrically controlled solid propellant(ECSP)offers multiple ignition and adjustable burning rate,serving as fuel for next-generation intelligent propulsion systems.To further enhance the combustion performance of ECSP,a method utilizing electrochemical and thermal decomposition catalysts has been proposed.In this work,we investigated the combustion characteristics of hydroxylamine nitrate(HAN)-based ECSP incorporating cerium oxide(CeO_(2))and graphene oxide(GO)by using an electrically controlled combustion test system.Electrochemical impedance spectroscopy(EIS)and linear sweep voltammetry(LSV)were used to measure the electrical conductibility and overpotential of ECSP with various additives,and Tafel curves were calculated.Thermogravimetric analysis coupled with differential scanning calorimetry(TG-DSC)was employed to investigate the thermal decomposition behavior of ECSP.While the addition of CeO_(2) and GO reduced the conductivity of ECSP,both catalysts exhibited strong electrocatalytic properties and facilitated the thermal decomposition of ECSP.Between two catalysts,GO demonstrated superior electrochemical catalytic performance but weaker thermal decomposition catalytic ability than CeO_(2).The addition of catalysts significantly enhanced the combustion performance of HAN-based ECSP.Specifically,the ignition delay time was shortened by 10%~20%.CeO_(2) raised the burning rate by approximately 20%but GO exhibited a remarkable boost of 40%in burning rate at high voltage.The combination of GO and PVA produced a flame-retardant substance that negatively impacted the ignition delay of ECSP and resulted in a smaller increase in the burning rate of ECSP at low ignition voltages.展开更多
The operational demands of a wide range significantly exacerbate combustion instability issues within ramjet combustor.To suppress combustion oscillations,an open-loop control system utilizing Linear Genetic Programmi...The operational demands of a wide range significantly exacerbate combustion instability issues within ramjet combustor.To suppress combustion oscillations,an open-loop control system utilizing Linear Genetic Programming(LGP)has been developed for a full-scale annular ramjet combustor.The LGP is used to generate control laws that include multi-frequency forcing.These laws are then transformed into square waves to actuate the solenoid valve,which modulates the kerosene supply for open-loop control.The results show that the duty cycle has little effect on instability amplitude,whereas an increase in frequency leads to a remarked reduction in combustion amplitude.After five generations evolvements,the pressure amplitude is reduced by 40.6% under the optimal control law generated by LGP.Furthermore,the machine learning process is depicted using a proximity map of control law similarity,with the search pathway visualized by the steepest descent.All individuals go forward to the upper left corner of the map with the evolution process,terminating at the optimal individual of the fifth generation.展开更多
The electrode structures in ignition devices for Electrically Controlled Solid Propellants(ECSP) can be classified into fixed and movable types. In movable electrode structures, springs are typically used to push the ...The electrode structures in ignition devices for Electrically Controlled Solid Propellants(ECSP) can be classified into fixed and movable types. In movable electrode structures, springs are typically used to push the electrodes and the propellant. The effects of spring pressure on the ignition and combustion of propellants have not yet been studied. In this paper, a universal testing machine and an electrochemical workstation were firstly utilized to investigate the compressive mechanical property and conductivity of Hydroxylamine Nitrate(HAN)-ECSP. The maximum pressure at which the propellant undergoes elastic deformation is 65 kPa. When the spring pressure increased from 5.1 k Pa to 20.4 kPa, the propellant resistance decreased from 56.8 Ω to 36.8 Ω.Various observation methods were employed to study the process of electrical energy injection and the ignition and combustion characteristics under constant voltage. Appropriately increasing the spring pressure can accelerate the injection of electrical energy into the propellant, increase the electrification current, and thus reduce the initial ignition delay time of the propellant. When the spring pressure is 20.4 kPa, the squeezing speed of the propellant is too fast, making it difficult for the propellant to be adequately heated at the electrode interface, which is unfavorable for ignition. Excessive spring pressure also leads to the accumulation of a large amount of combustion residue on the electrode plate, hindering the mixing and diffusion of hot gases during the second ignition process, preventing the gaseous flame of the propellant. When the spring pressure is 5.1 kPa, improving the working voltage can enhance the repeated ignition characteristics of the propellant.展开更多
This paper solves the problem of model-free dual-arm space robot maneuvering after non-cooperative target capture under high control quality requirements.The explicit system model is unavailable,and the maneuvering mi...This paper solves the problem of model-free dual-arm space robot maneuvering after non-cooperative target capture under high control quality requirements.The explicit system model is unavailable,and the maneuvering mission is disturbed by the measurement noise and the target adversarial behavior.To address these problems,a model-free Combined Adaptive-length Datadriven Predictive Controller(CADPC)is proposed.It consists of a separated subsystem identification method and a combined predictive control strategy.The subsystem identification method is composed of an adaptive data length,thereby reducing sensitivity to undetermined measurement noises and disturbances.Based on the subsystem identification,the combined predictive controller is established,reducing calculating resource.The stability of the CADPC is rigorously proven using the Input-to-State Stable(ISS)theorem and the small-gain theorem.Simulations demonstrate that CADPC effectively handles the model-free space robot post operation in the presence of significant disturbances,state measurement noise,and control input errors.It achieves improved steady-state accuracy,reduced steady-state control consumption,and minimized control input chattering.展开更多
Mosquito-borne diseases pose a significant global health threat,necessitating the development of innovative vector control strategies.In this study,we investigated the potential of harnessing host immunity against mos...Mosquito-borne diseases pose a significant global health threat,necessitating the development of innovative vector control strategies.In this study,we investigated the potential of harnessing host immunity against mosquitoes through vaccination.Using Culex pipiens(C.pipiens)as a model,we demonstrated that polyclonal antibodies against C.pipiens abdominal protein extracts significantly impaired oviposition and increased mosquito mortality,primarily through the classical complement activation pathways.However,repeated exposure led to resistance,indicating potential adaptation.Proteomic analysis identified metabolic proteins as key targets,with Gene Ontology and Kyoto Encyclopedia of Genes and Genomes enrichment analyses highlighting their roles in carboxylic acid metabolism,tyrosine degradation,and the proteasome pathways.Notably,cross-species reactivity was revealed by Western blotting,showing strong binding of Culex-specific antibodies to Anopheles and Aedes abdominal proteins.This study provides mechanistic insights into antibody-based mosquito suppression,highlighting its potential as an innovative vector control strategy while underscoring the need for further research on resistance management and ecological impacts.展开更多
This paper examines a model that combines vortex generators and leading-edge tubercles for controlling the laminar separation bubble(LSB)over an airfoil at low Reynolds numbers(Re).This new concept of passive flow con...This paper examines a model that combines vortex generators and leading-edge tubercles for controlling the laminar separation bubble(LSB)over an airfoil at low Reynolds numbers(Re).This new concept of passive flow control technique utilizing a tubercle and vortex generator(VG)close to the leading edge was analyzed numerically for a NACA0015 airfoil.In this study,the Shear Stress Transport(SST)turbulence model was employed in the numerical modelling.Numerical modelling was completed using the ANSYS-Fluent 18.2 solver.Analyses were conducted to investigate the flow pattern and understand the underlying LSB control phenomena that enabled the new passive flow control method to provide this significant performance benefit.The findings indicated that the new concept of passive flow control technique suppressed the formation of an LSB at the suction surface of the NACA0015 airfoil,resulting in a higher lift coefficient and improved aerodynamic performance.Improvements in LSB dynamics and aerodynamic performance through the passive flow control method lead to increased energy output and enhanced stability.展开更多
The combustion behavior of Ti-Al-Mo-Zr-Sn-W alloy(TC25G)was studied in a high-temperature and high-speed air flow environment using the laser ignition method combined with ultra-high temperature infrared thermometer,s...The combustion behavior of Ti-Al-Mo-Zr-Sn-W alloy(TC25G)was studied in a high-temperature and high-speed air flow environment using the laser ignition method combined with ultra-high temperature infrared thermometer,scanning electron microscope,X-ray diffractometer,and transmission electron microscope.The burn-resistant performance of TC25G and TC11 alloys was compared.Meanwhile,the microstructural characteristics,crystal structure,and formation mechanism of the combustion products of TC25G alloy were analyzed in detail.The results show that the high-temperature and high-speed air flow promotes combustion within the air flow temperature range of 200–400℃and the air flow velocity range of 0–100 m/s.The combustion path advances along the direction of the air flow.The combustion of TC25G alloy mainly relies on the diffusion of the oxygen and the expansion of the combustion area caused by the movement of the melt.Based on the microstructure and composition of combustion product,it can be divided into the combustion zone,the melting zone,and the heat affected zone.During combustion,the formation of microstructures is closely correlated with the behavior of alloying elements and their selective combination with O.The major oxidation products of Ti are TiO and TiO_(2).The oxides formed by Mo and W hinder the movement of the melt during the combustion.Al and Zr tend to undergo internal oxidation.Al_(2)O_(3)precipitates on the surface of ZrO_(2),forming a protective oxide layer that inhibits the inward diffusion of O.Moreover,the element enrichment at the interface between the melting zone and the heat affected zone increases the melting point on the solid side,hindering the migration of the solid-liquid interface.展开更多
Steady speed control of agricultural machinery can improve operating quality and efficiency.To address the impact of farmland slope variations on the speed stability of unmanned operation agricultural machinery,a hybr...Steady speed control of agricultural machinery can improve operating quality and efficiency.To address the impact of farmland slope variations on the speed stability of unmanned operation agricultural machinery,a hybrid control method was proposed.This method included a hybrid controller composed of a slope-based controller and a proportional-integral-derivative(PID)controller.The speed of agricultural machinery was influenced by longitudinal forces,which were divided into two parts:one part was slope-related forces and conventional resistance,and the other was hard-to-estimate forces,such as sliding friction.For the first part,a slope-based controller was designed;for the second part,a PID controller was implemented.By combining these two controllers,the system can dynamically adjust the throttle opening and the brake master cylinder pressure,ensuring steady speed travel on sloping farmland.Simulation tests at a target speed of 7 km/h demonstrated that the proposed controller maintained a stable speed,achieving a root mean square error of 0.13 km/h and a mean absolute percentage error of 1.6%.Field tests on a practical experimental platform validated the method’s effectiveness,with results showing consistent control performance across varying slope conditions.The proposed controller demonstrated superior control performance.Experimental data verified that this method can achieve precise control of the agricultural machinery’s movement speed,meeting the stability requirements for agricultural operations.展开更多
This study investigates prescribed-time position tracking control for electromagnetic satellite formations subject to model uncertainties and external disturbances.Using the Clohessy-Wiltshire equations as the relativ...This study investigates prescribed-time position tracking control for electromagnetic satellite formations subject to model uncertainties and external disturbances.Using the Clohessy-Wiltshire equations as the relative motion dynamics model,a prescribed time output feedback control strategy is proposed.A prescribed-time extended state observer is designed to estimate the relative velocity and external disturbances.The disturbance estimates are then used as the feedforward component of the controller.Building on this framework,a novel prescribed-time active disturbance rejection control strategy for position tracking is developed via a backstepping control design.The convergence of the extended state observer and the stability of the closed-loop system are rigorously analyzed using Lyapunov stability theory.Numerical simulations are performed to validate the effectiveness of the proposed controller.展开更多
Coal cinder is an abundant byproduct of the extensive consumption of coal in industrial production and daily life.Making full use of the cinder is conducive to a low-carbon economy.In this study,inspired by the burnin...Coal cinder is an abundant byproduct of the extensive consumption of coal in industrial production and daily life.Making full use of the cinder is conducive to a low-carbon economy.In this study,inspired by the burning of coal,a new method for constructing a silica-based composite porous material(SiO_(2)-CPM)was developed by combusting a siloxane-modified anthracite coal gel(CSiO_(2) gel).During this process,the combustion product was directly converted into a porous material,and the calorific value of the coal remained nearly unchanged(~98%of the original calorific value was retained),demonstrating the viability of this method for energy-efficient applications.The SiO_(2)-CPM exhibited an ultra-low thermal conductivity(0.036 W/(m·K)at room temperature),outperforming conventional insulation materials(e.g.,cotton~0.05 W/(m·K)).Additionally,it showed enhanced mechanical strength(fracture stress of 41.8 kPa)compared to the powder state of the coal cinder.Experimental results indicate that the amount of siloxane,structure-directing agent,and an acidic environment were critical for mechanical enhancement.The SiO_(2)-CPM showed good dimensional stability against thermal expansion and exhibited excellent thermal insulation and fire resistance even at 900℃.Meanwhile,the SiO_(2)-CPM with complex geometry could be easily fabricated using this method owing to the excellent shaping ability of the CSiO_(2) gel.Compared to conventional methods such as sol-gel synthesis or freeze-drying,this approach for fabricating SiO_(2)-CPM is simpler and cost-effective and allows the direct utilization of coal cinder post-combustion.展开更多
As a closed-loop learning control method,repetitive control has been widely used in a variety of areas from appliances to aviation.A repetitive control system features perfect reference tracking and disturbance reject...As a closed-loop learning control method,repetitive control has been widely used in a variety of areas from appliances to aviation.A repetitive control system features perfect reference tracking and disturbance rejection in the steady state for periodic signals with a fixed period.This characteristic is important not only for conventional technologies and conventional industries but also for advanced technologies and emerging industries.This paper first explains the concept of repetitive control from its original idea.Next,it describes the structure of a repetitive controller as an internal model and shows the respective points of continuous-and discrete-time repetitive control.It presents a categorized list of practical applications of repetitive control.Moreover,two concrete applications,namely the control of a robotic manipulator and a rotating system,demonstrate the validity of the method with experimental results.Several current studies in this field are also reviewed,and some challenges and future studies for repetitive control are provided.展开更多
This article investigates the robust current tracking control problem of three-phase grid-connected inverters with LCL filter under external disturbance by a dynamic state feedback control method.First,this paper cons...This article investigates the robust current tracking control problem of three-phase grid-connected inverters with LCL filter under external disturbance by a dynamic state feedback control method.First,this paper constructs an internal model to learn the information of the states and input of the grid-connected inverter under steady state.Second,by utilizing the internal model principle,the paper turns the tracking control problem into the robust stabilization control problem based on some appropriate coordinate transformations.Then,The paper designs a dynamics state feedback control law to deal with this robust stabilization problem,and thus the solution of the robust current tracking control problem of three-phase grid-connected inverters can be obtained.This control method can ensure the asymptotic stability of the closedloop system.Finally,the paper illustrates the effectiveness of the proposed control approach through several groups of simulations,and compares it with the feedforward control method to verify the robustness of the proposed control method to uncertain parameters.展开更多
Aiming to solve the steering instability and hysteresis of agricultural robots in the process of movement,a fusion PID control method of particle swarm optimization(PSO)and genetic algorithm(GA)was proposed.The fusion...Aiming to solve the steering instability and hysteresis of agricultural robots in the process of movement,a fusion PID control method of particle swarm optimization(PSO)and genetic algorithm(GA)was proposed.The fusion algorithm took advantage of the fast optimization ability of PSO to optimize the population screening link of GA.The Simulink simulation results showed that the convergence of the fitness function of the fusion algorithm was accelerated,the system response adjustment time was reduced,and the overshoot was almost zero.Then the algorithm was applied to the steering test of agricultural robot in various scenes.After modeling the steering system of agricultural robot,the steering test results in the unloaded suspended state showed that the PID control based on fusion algorithm reduced the rise time,response adjustment time and overshoot of the system,and improved the response speed and stability of the system,compared with the artificial trial and error PID control and the PID control based on GA.The actual road steering test results showed that the PID control response rise time based on the fusion algorithm was the shortest,about 4.43 s.When the target pulse number was set to 100,the actual mean value in the steady-state regulation stage was about 102.9,which was the closest to the target value among the three control methods,and the overshoot was reduced at the same time.The steering test results under various scene states showed that the PID control based on the proposed fusion algorithm had good anti-interference ability,it can adapt to the changes of environment and load and improve the performance of the control system.It was effective in the steering control of agricultural robot.This method can provide a reference for the precise steering control of other robots.展开更多
To solve the problem of in-flight actuator faults and parameter uncertainties for multiple Unmanned Aerial Vehicles(UAVs),and reduce the communication and computational resource consumption of multiple UAVs,a Fraction...To solve the problem of in-flight actuator faults and parameter uncertainties for multiple Unmanned Aerial Vehicles(UAVs),and reduce the communication and computational resource consumption of multiple UAVs,a Fraction-Order(FO)sliding-mode Fault-Tolerant Cooperative Control(FTCC)strategy is proposed for multiple UAVs based on Event-Triggered Communication Mechanism(ET-COM-M)and Event-Triggered Control Mechanism(ET-CON-M).First,by considering the limited communication bandwidth of multiple UAVs in formation,an ET-COM-M is designed to significantly reduce communication times.Then,a distributed observer is skillfully constructed to estimate the reference signals for follower UAVs.Moreover,the adaptive strategy is incorporated into the Radial Basis Function Neural Network(RBFNN)to learn the lumped unknown terms for handling bias actuator faults and parameter uncertainties.Besides,the Nussbaum method is used to deal with the loss-of-effectiveness faults.To further achieve the refined control performance against faults,FO calculus is artfully integrated into the sliding-mode control protocol with ET-CON-M.Finally,Zeno behavior is excluded by rigorous theoretical analysis and Lyapunov stability is proved to show the effectiveness of the designed FTCC strategy.Simulation results show that the designed FTCC strategy with Event-Triggered Mechanism(ETM)can guarantee the safety of multiple UAVs and simultaneously reduce the communication and control frequencies,making the developed control scheme applicable in engineering.展开更多
Mobile wheel-legged robots exhibiting mobility,stability and reliability have garnered heightened research attention in demanding real-world scenarios,especially in material transport,emergency response and space expl...Mobile wheel-legged robots exhibiting mobility,stability and reliability have garnered heightened research attention in demanding real-world scenarios,especially in material transport,emergency response and space exploration.The kinematics model merely delineates the geometric relationship of the controlled objective,disregarding force feedback.This study investigates model predictive trajectory tracking control utilising the robot dynamic model(DRMPC)in the context of unpredictable interactions.The predictive tracking controller for the wheel-legged robot is introduced in the context of position tracking.A dynamic approximator is employed to address the uncertain interactions in the tracking process.Ultimately,cosimulation and empirical tests are conducted to demonstrate the efficacy of the devised control methodology,which achieves high precision and dependable robustness.This work can elucidate the technical and practical oversight of autonomous movement in complicated environments and enhance the manoeuverability and flexibility.展开更多
In composite solid propellants with high aluminum(Al)content and low burning rate,incomplete combustion of the Al powder may occur.In this study,varying lithium(Li)content in Al-Li alloy powder was utilized instead of...In composite solid propellants with high aluminum(Al)content and low burning rate,incomplete combustion of the Al powder may occur.In this study,varying lithium(Li)content in Al-Li alloy powder was utilized instead of pure aluminum particles to mitigate agglomeration and enhance the combustion efficiency of solid propellants(Combustion efficiency herein refers to the completeness of metallic fuel oxidation,quantified as the ratio of actual-to-theoretical energy released during combustion)with high Al content and low burning rates.The impact of Al-Li alloy with different Li contents on combustion and agglomeration of solid propellant was investigated using explosion heat,combustion heat,differential thermal analysis(DTA),thermos-gravimetric analysis(TG),dynamic high-pressure combustion test,ignition experiment of small solid rocket motor(SRM)tests,condensation combustion product collection,and X-ray diffraction techniques(XRD).Compared with pure Al,Al-Li alloys exhibit higher combustion heat,which contributes to improved combustion efficiency in Al-Li alloy-containing propellants.DTA and TG analyses demonstrated higher reactivity and lower ignition temperatures for Al-Li alloys.High-pressure combustion experiments at 5 MPa showed that Al-Li alloy fuel significantly decreases combustion agglomeration.The results from theφ75 mm andφ165 mm SRM and XRD tests further support this finding.This study provides novel insights into the combustion and agglomeration behaviors of high-Al,low-burning-rate composite solid propellants and supports the potential application of Al-Li alloys in advanced propellant formulations.展开更多
This paper presents an adaptive formation control method for a heterogeneous robot swarm,utilising a multilevel formation task tree to model various types of formation tasks and a single-state distributed k-winner-tak...This paper presents an adaptive formation control method for a heterogeneous robot swarm,utilising a multilevel formation task tree to model various types of formation tasks and a single-state distributed k-winner-take-all(S-DKWTA)algorithm to address the MRTA problem.In addition,we propose an enhanced load reassignment algorithm to resolve conflicts when using S-DKWTA.The S-DKWTA algorithm demonstrates the capability to manage multiple objectives and dynamically select leaders in real-time,thereby optimising formation efficiency and reducing energy consumption.The proposed approach integrates an enhanced artificial potential field(APF)to govern the motion of heterogeneous robot systems which encompasses both unmanned ground vehicles(UGVs)and unmanned aerial vehicles(UAVs),thereby achieving collision and obstacle avoidance.Simulations employing UGVs and UAVs swarm to achieve formation movement demonstrate the efficacy of this approach.The amalgamation of S-DKWTA and improved APF ensures stable and adaptable formation control,underscoring its potential for diverse multirobot applications.展开更多
This paper is concerned with adaptive consensus tracking control of nonlinear multi-agent systems with actuator faults and unknown nonidentical control directions under double semi-Markovian switching topologies.Consi...This paper is concerned with adaptive consensus tracking control of nonlinear multi-agent systems with actuator faults and unknown nonidentical control directions under double semi-Markovian switching topologies.Considering the complex working environment and the stability differences in communication links between leaders and followers,a double semi-Markov process is first introduced to describe the random switching of communication topologies in the leader-follower structure.In order to address challenges from the unknown nonidentical control directions and partial loss of effectiveness actuator faults,a completely independent parameter is introduced into the Nussbaum function to overcome the inherent obstacle of mutual cancellation and avoid the rapid growth rate.Considering only the state information of agents is transmitted among the agents,an adaptive distributed fault-tolerant consensus tracking control is proposed based on the double semi-Markovian switching topologies using the designed Nussbaum function.Furthermore,the stability of the closed-loop nonlinear multi-agent systems is analyzed using contradiction argument and Lyapunov theorem,from which the asymptotic consensus tracking in mean square sense can be obtained.A numerical simulation example is provided to verify the effectiveness of the proposed algorithm.展开更多
In this paper,we consider the maximal positive definite solution of the nonlinear matrix equation.By using the idea of Algorithm 2.1 in ZHANG(2013),a new inversion-free method with a stepsize parameter is proposed to ...In this paper,we consider the maximal positive definite solution of the nonlinear matrix equation.By using the idea of Algorithm 2.1 in ZHANG(2013),a new inversion-free method with a stepsize parameter is proposed to obtain the maximal positive definite solution of nonlinear matrix equation X+A^(*)X|^(-α)A=Q with the case 0<α≤1.Based on this method,a new iterative algorithm is developed,and its convergence proof is given.Finally,two numerical examples are provided to show the effectiveness of the proposed method.展开更多
As an important resource in data link,time slots should be strategically allocated to enhance transmission efficiency and resist eavesdropping,especially considering the tremendous increase in the number of nodes and ...As an important resource in data link,time slots should be strategically allocated to enhance transmission efficiency and resist eavesdropping,especially considering the tremendous increase in the number of nodes and diverse communication needs.It is crucial to design control sequences with robust randomness and conflict-freeness to properly address differentiated access control in data link.In this paper,we propose a hierarchical access control scheme based on control sequences to achieve high utilization of time slots and differentiated access control.A theoretical bound of the hierarchical control sequence set is derived to characterize the constraints on the parameters of the sequence set.Moreover,two classes of optimal hierarchical control sequence sets satisfying the theoretical bound are constructed,both of which enable the scheme to achieve maximum utilization of time slots.Compared with the fixed time slot allocation scheme,our scheme reduces the symbol error rate by up to 9%,which indicates a significant improvement in anti-interference and eavesdropping capabilities.展开更多
基金supported by the National Natural Science Foundation of China(Grant No.12074187).
文摘Electrically controlled solid propellant(ECSP)offers multiple ignition and adjustable burning rate,serving as fuel for next-generation intelligent propulsion systems.To further enhance the combustion performance of ECSP,a method utilizing electrochemical and thermal decomposition catalysts has been proposed.In this work,we investigated the combustion characteristics of hydroxylamine nitrate(HAN)-based ECSP incorporating cerium oxide(CeO_(2))and graphene oxide(GO)by using an electrically controlled combustion test system.Electrochemical impedance spectroscopy(EIS)and linear sweep voltammetry(LSV)were used to measure the electrical conductibility and overpotential of ECSP with various additives,and Tafel curves were calculated.Thermogravimetric analysis coupled with differential scanning calorimetry(TG-DSC)was employed to investigate the thermal decomposition behavior of ECSP.While the addition of CeO_(2) and GO reduced the conductivity of ECSP,both catalysts exhibited strong electrocatalytic properties and facilitated the thermal decomposition of ECSP.Between two catalysts,GO demonstrated superior electrochemical catalytic performance but weaker thermal decomposition catalytic ability than CeO_(2).The addition of catalysts significantly enhanced the combustion performance of HAN-based ECSP.Specifically,the ignition delay time was shortened by 10%~20%.CeO_(2) raised the burning rate by approximately 20%but GO exhibited a remarkable boost of 40%in burning rate at high voltage.The combination of GO and PVA produced a flame-retardant substance that negatively impacted the ignition delay of ECSP and resulted in a smaller increase in the burning rate of ECSP at low ignition voltages.
基金support from the National Natural Science Foundation of China(No.12002372)the Young Elite Scientists Sponsorship Program by China Association for Science and Technology(No.2022QNRC001)the Natural Science Foundation of Hunan Province,China(No.2021JJ40674)。
文摘The operational demands of a wide range significantly exacerbate combustion instability issues within ramjet combustor.To suppress combustion oscillations,an open-loop control system utilizing Linear Genetic Programming(LGP)has been developed for a full-scale annular ramjet combustor.The LGP is used to generate control laws that include multi-frequency forcing.These laws are then transformed into square waves to actuate the solenoid valve,which modulates the kerosene supply for open-loop control.The results show that the duty cycle has little effect on instability amplitude,whereas an increase in frequency leads to a remarked reduction in combustion amplitude.After five generations evolvements,the pressure amplitude is reduced by 40.6% under the optimal control law generated by LGP.Furthermore,the machine learning process is depicted using a proximity map of control law similarity,with the search pathway visualized by the steepest descent.All individuals go forward to the upper left corner of the map with the evolution process,terminating at the optimal individual of the fifth generation.
基金supported by the National Natural Science Foundation of China(Nos.T222100,22205258,52302485 and 2024JJ5404).
文摘The electrode structures in ignition devices for Electrically Controlled Solid Propellants(ECSP) can be classified into fixed and movable types. In movable electrode structures, springs are typically used to push the electrodes and the propellant. The effects of spring pressure on the ignition and combustion of propellants have not yet been studied. In this paper, a universal testing machine and an electrochemical workstation were firstly utilized to investigate the compressive mechanical property and conductivity of Hydroxylamine Nitrate(HAN)-ECSP. The maximum pressure at which the propellant undergoes elastic deformation is 65 kPa. When the spring pressure increased from 5.1 k Pa to 20.4 kPa, the propellant resistance decreased from 56.8 Ω to 36.8 Ω.Various observation methods were employed to study the process of electrical energy injection and the ignition and combustion characteristics under constant voltage. Appropriately increasing the spring pressure can accelerate the injection of electrical energy into the propellant, increase the electrification current, and thus reduce the initial ignition delay time of the propellant. When the spring pressure is 20.4 kPa, the squeezing speed of the propellant is too fast, making it difficult for the propellant to be adequately heated at the electrode interface, which is unfavorable for ignition. Excessive spring pressure also leads to the accumulation of a large amount of combustion residue on the electrode plate, hindering the mixing and diffusion of hot gases during the second ignition process, preventing the gaseous flame of the propellant. When the spring pressure is 5.1 kPa, improving the working voltage can enhance the repeated ignition characteristics of the propellant.
基金supported by the National Natural Science Foundation of China(No.12372045)the National Key Research and the Development Program of China(Nos.2023YFC2205900,2023YFC2205901)。
文摘This paper solves the problem of model-free dual-arm space robot maneuvering after non-cooperative target capture under high control quality requirements.The explicit system model is unavailable,and the maneuvering mission is disturbed by the measurement noise and the target adversarial behavior.To address these problems,a model-free Combined Adaptive-length Datadriven Predictive Controller(CADPC)is proposed.It consists of a separated subsystem identification method and a combined predictive control strategy.The subsystem identification method is composed of an adaptive data length,thereby reducing sensitivity to undetermined measurement noises and disturbances.Based on the subsystem identification,the combined predictive controller is established,reducing calculating resource.The stability of the CADPC is rigorously proven using the Input-to-State Stable(ISS)theorem and the small-gain theorem.Simulations demonstrate that CADPC effectively handles the model-free space robot post operation in the presence of significant disturbances,state measurement noise,and control input errors.It achieves improved steady-state accuracy,reduced steady-state control consumption,and minimized control input chattering.
基金supported by the National Natural Science Foundation of China(Grant No.82472312).
文摘Mosquito-borne diseases pose a significant global health threat,necessitating the development of innovative vector control strategies.In this study,we investigated the potential of harnessing host immunity against mosquitoes through vaccination.Using Culex pipiens(C.pipiens)as a model,we demonstrated that polyclonal antibodies against C.pipiens abdominal protein extracts significantly impaired oviposition and increased mosquito mortality,primarily through the classical complement activation pathways.However,repeated exposure led to resistance,indicating potential adaptation.Proteomic analysis identified metabolic proteins as key targets,with Gene Ontology and Kyoto Encyclopedia of Genes and Genomes enrichment analyses highlighting their roles in carboxylic acid metabolism,tyrosine degradation,and the proteasome pathways.Notably,cross-species reactivity was revealed by Western blotting,showing strong binding of Culex-specific antibodies to Anopheles and Aedes abdominal proteins.This study provides mechanistic insights into antibody-based mosquito suppression,highlighting its potential as an innovative vector control strategy while underscoring the need for further research on resistance management and ecological impacts.
基金the Scientific Research Projects Unit of Erciyes University under contract no:FDS-2022-11532 and FOA-2025-14773.
文摘This paper examines a model that combines vortex generators and leading-edge tubercles for controlling the laminar separation bubble(LSB)over an airfoil at low Reynolds numbers(Re).This new concept of passive flow control technique utilizing a tubercle and vortex generator(VG)close to the leading edge was analyzed numerically for a NACA0015 airfoil.In this study,the Shear Stress Transport(SST)turbulence model was employed in the numerical modelling.Numerical modelling was completed using the ANSYS-Fluent 18.2 solver.Analyses were conducted to investigate the flow pattern and understand the underlying LSB control phenomena that enabled the new passive flow control method to provide this significant performance benefit.The findings indicated that the new concept of passive flow control technique suppressed the formation of an LSB at the suction surface of the NACA0015 airfoil,resulting in a higher lift coefficient and improved aerodynamic performance.Improvements in LSB dynamics and aerodynamic performance through the passive flow control method lead to increased energy output and enhanced stability.
基金China“Ye Qisun”Science Foundation Project of National Natural Science Foundation(U2141222)Innovation Fund(8F231527Z)。
文摘The combustion behavior of Ti-Al-Mo-Zr-Sn-W alloy(TC25G)was studied in a high-temperature and high-speed air flow environment using the laser ignition method combined with ultra-high temperature infrared thermometer,scanning electron microscope,X-ray diffractometer,and transmission electron microscope.The burn-resistant performance of TC25G and TC11 alloys was compared.Meanwhile,the microstructural characteristics,crystal structure,and formation mechanism of the combustion products of TC25G alloy were analyzed in detail.The results show that the high-temperature and high-speed air flow promotes combustion within the air flow temperature range of 200–400℃and the air flow velocity range of 0–100 m/s.The combustion path advances along the direction of the air flow.The combustion of TC25G alloy mainly relies on the diffusion of the oxygen and the expansion of the combustion area caused by the movement of the melt.Based on the microstructure and composition of combustion product,it can be divided into the combustion zone,the melting zone,and the heat affected zone.During combustion,the formation of microstructures is closely correlated with the behavior of alloying elements and their selective combination with O.The major oxidation products of Ti are TiO and TiO_(2).The oxides formed by Mo and W hinder the movement of the melt during the combustion.Al and Zr tend to undergo internal oxidation.Al_(2)O_(3)precipitates on the surface of ZrO_(2),forming a protective oxide layer that inhibits the inward diffusion of O.Moreover,the element enrichment at the interface between the melting zone and the heat affected zone increases the melting point on the solid side,hindering the migration of the solid-liquid interface.
文摘Steady speed control of agricultural machinery can improve operating quality and efficiency.To address the impact of farmland slope variations on the speed stability of unmanned operation agricultural machinery,a hybrid control method was proposed.This method included a hybrid controller composed of a slope-based controller and a proportional-integral-derivative(PID)controller.The speed of agricultural machinery was influenced by longitudinal forces,which were divided into two parts:one part was slope-related forces and conventional resistance,and the other was hard-to-estimate forces,such as sliding friction.For the first part,a slope-based controller was designed;for the second part,a PID controller was implemented.By combining these two controllers,the system can dynamically adjust the throttle opening and the brake master cylinder pressure,ensuring steady speed travel on sloping farmland.Simulation tests at a target speed of 7 km/h demonstrated that the proposed controller maintained a stable speed,achieving a root mean square error of 0.13 km/h and a mean absolute percentage error of 1.6%.Field tests on a practical experimental platform validated the method’s effectiveness,with results showing consistent control performance across varying slope conditions.The proposed controller demonstrated superior control performance.Experimental data verified that this method can achieve precise control of the agricultural machinery’s movement speed,meeting the stability requirements for agricultural operations.
文摘This study investigates prescribed-time position tracking control for electromagnetic satellite formations subject to model uncertainties and external disturbances.Using the Clohessy-Wiltshire equations as the relative motion dynamics model,a prescribed time output feedback control strategy is proposed.A prescribed-time extended state observer is designed to estimate the relative velocity and external disturbances.The disturbance estimates are then used as the feedforward component of the controller.Building on this framework,a novel prescribed-time active disturbance rejection control strategy for position tracking is developed via a backstepping control design.The convergence of the extended state observer and the stability of the closed-loop system are rigorously analyzed using Lyapunov stability theory.Numerical simulations are performed to validate the effectiveness of the proposed controller.
基金supported by the National Natural Science Foundation of China(No.52573220)the National Key R&D Program of China(No.2023YFC3404201)+1 种基金the Fundamental Research Funds for the Central Universities(No.FRF-IDRY-GD24-005)the State Key Laboratory of Solid Waste Reuse for Building Materials(No.SWR-2022-009).
文摘Coal cinder is an abundant byproduct of the extensive consumption of coal in industrial production and daily life.Making full use of the cinder is conducive to a low-carbon economy.In this study,inspired by the burning of coal,a new method for constructing a silica-based composite porous material(SiO_(2)-CPM)was developed by combusting a siloxane-modified anthracite coal gel(CSiO_(2) gel).During this process,the combustion product was directly converted into a porous material,and the calorific value of the coal remained nearly unchanged(~98%of the original calorific value was retained),demonstrating the viability of this method for energy-efficient applications.The SiO_(2)-CPM exhibited an ultra-low thermal conductivity(0.036 W/(m·K)at room temperature),outperforming conventional insulation materials(e.g.,cotton~0.05 W/(m·K)).Additionally,it showed enhanced mechanical strength(fracture stress of 41.8 kPa)compared to the powder state of the coal cinder.Experimental results indicate that the amount of siloxane,structure-directing agent,and an acidic environment were critical for mechanical enhancement.The SiO_(2)-CPM showed good dimensional stability against thermal expansion and exhibited excellent thermal insulation and fire resistance even at 900℃.Meanwhile,the SiO_(2)-CPM with complex geometry could be easily fabricated using this method owing to the excellent shaping ability of the CSiO_(2) gel.Compared to conventional methods such as sol-gel synthesis or freeze-drying,this approach for fabricating SiO_(2)-CPM is simpler and cost-effective and allows the direct utilization of coal cinder post-combustion.
基金supported in part by the Japan Society for the Promotion of Science Grants-in-Aid for Scientific Research(B)(23K25252,24K03325)the National Natural Science Foundation of China(61873348)the Natural Science Foundation of Hubei Province,China(2020CFA031)。
文摘As a closed-loop learning control method,repetitive control has been widely used in a variety of areas from appliances to aviation.A repetitive control system features perfect reference tracking and disturbance rejection in the steady state for periodic signals with a fixed period.This characteristic is important not only for conventional technologies and conventional industries but also for advanced technologies and emerging industries.This paper first explains the concept of repetitive control from its original idea.Next,it describes the structure of a repetitive controller as an internal model and shows the respective points of continuous-and discrete-time repetitive control.It presents a categorized list of practical applications of repetitive control.Moreover,two concrete applications,namely the control of a robotic manipulator and a rotating system,demonstrate the validity of the method with experimental results.Several current studies in this field are also reviewed,and some challenges and future studies for repetitive control are provided.
基金Supported by the Fundamental Research Funds for the Central Universities(2024ZYGXZR047)the National Natural Science Foundation of China(62373156)the Guangdong Basic and Applied Basic Research Foundation(2024A1515011736)。
文摘This article investigates the robust current tracking control problem of three-phase grid-connected inverters with LCL filter under external disturbance by a dynamic state feedback control method.First,this paper constructs an internal model to learn the information of the states and input of the grid-connected inverter under steady state.Second,by utilizing the internal model principle,the paper turns the tracking control problem into the robust stabilization control problem based on some appropriate coordinate transformations.Then,The paper designs a dynamics state feedback control law to deal with this robust stabilization problem,and thus the solution of the robust current tracking control problem of three-phase grid-connected inverters can be obtained.This control method can ensure the asymptotic stability of the closedloop system.Finally,the paper illustrates the effectiveness of the proposed control approach through several groups of simulations,and compares it with the feedforward control method to verify the robustness of the proposed control method to uncertain parameters.
文摘Aiming to solve the steering instability and hysteresis of agricultural robots in the process of movement,a fusion PID control method of particle swarm optimization(PSO)and genetic algorithm(GA)was proposed.The fusion algorithm took advantage of the fast optimization ability of PSO to optimize the population screening link of GA.The Simulink simulation results showed that the convergence of the fitness function of the fusion algorithm was accelerated,the system response adjustment time was reduced,and the overshoot was almost zero.Then the algorithm was applied to the steering test of agricultural robot in various scenes.After modeling the steering system of agricultural robot,the steering test results in the unloaded suspended state showed that the PID control based on fusion algorithm reduced the rise time,response adjustment time and overshoot of the system,and improved the response speed and stability of the system,compared with the artificial trial and error PID control and the PID control based on GA.The actual road steering test results showed that the PID control response rise time based on the fusion algorithm was the shortest,about 4.43 s.When the target pulse number was set to 100,the actual mean value in the steady-state regulation stage was about 102.9,which was the closest to the target value among the three control methods,and the overshoot was reduced at the same time.The steering test results under various scene states showed that the PID control based on the proposed fusion algorithm had good anti-interference ability,it can adapt to the changes of environment and load and improve the performance of the control system.It was effective in the steering control of agricultural robot.This method can provide a reference for the precise steering control of other robots.
基金supported in part by National Natural Science Foundation of China(Nos.62373188,62003162)the Natural Science Foundation of Jiangsu Province of China(Nos.BK20240182,BK20222012)+2 种基金the Industry-University Research Innovation Foundation for the Chinese Ministry of Education(No.2021ZYA02005)the Aeronautical Science Foundation of China(Nos.20220007052003,20200007018001)the Fundamental Research Funds for the Central Universities,China(Nos.NE2024004,NI2024001)。
文摘To solve the problem of in-flight actuator faults and parameter uncertainties for multiple Unmanned Aerial Vehicles(UAVs),and reduce the communication and computational resource consumption of multiple UAVs,a Fraction-Order(FO)sliding-mode Fault-Tolerant Cooperative Control(FTCC)strategy is proposed for multiple UAVs based on Event-Triggered Communication Mechanism(ET-COM-M)and Event-Triggered Control Mechanism(ET-CON-M).First,by considering the limited communication bandwidth of multiple UAVs in formation,an ET-COM-M is designed to significantly reduce communication times.Then,a distributed observer is skillfully constructed to estimate the reference signals for follower UAVs.Moreover,the adaptive strategy is incorporated into the Radial Basis Function Neural Network(RBFNN)to learn the lumped unknown terms for handling bias actuator faults and parameter uncertainties.Besides,the Nussbaum method is used to deal with the loss-of-effectiveness faults.To further achieve the refined control performance against faults,FO calculus is artfully integrated into the sliding-mode control protocol with ET-CON-M.Finally,Zeno behavior is excluded by rigorous theoretical analysis and Lyapunov stability is proved to show the effectiveness of the designed FTCC strategy.Simulation results show that the designed FTCC strategy with Event-Triggered Mechanism(ETM)can guarantee the safety of multiple UAVs and simultaneously reduce the communication and control frequencies,making the developed control scheme applicable in engineering.
基金supported by the National Natural Science Foundation of China(62203176,62173038)Guangzhou Key Research and Development Program(2025B03J0072)+5 种基金Guangdong High-Level Talents Special Support Programme(2024TQ08Z107)Anhui Province Natural Science Funds for Distinguished Young Scholar(2308085J02)State Key Laboratory of Intelligent Vehicle Safety Technology(IVSTSKL-202402,IVSTSKL-202430,IVSTSKL-202508,IVSTSKL-202520)State Key Laboratory of Intelligent Green Vehicle and Mobility(KFY2417)State Key Laboratory of Advanced Design and Manufacturing for Vehicle Body(32215010),Wuhu Major Scientific and Technological Achievements Engineering Project(2021zc04).
文摘Mobile wheel-legged robots exhibiting mobility,stability and reliability have garnered heightened research attention in demanding real-world scenarios,especially in material transport,emergency response and space exploration.The kinematics model merely delineates the geometric relationship of the controlled objective,disregarding force feedback.This study investigates model predictive trajectory tracking control utilising the robot dynamic model(DRMPC)in the context of unpredictable interactions.The predictive tracking controller for the wheel-legged robot is introduced in the context of position tracking.A dynamic approximator is employed to address the uncertain interactions in the tracking process.Ultimately,cosimulation and empirical tests are conducted to demonstrate the efficacy of the devised control methodology,which achieves high precision and dependable robustness.This work can elucidate the technical and practical oversight of autonomous movement in complicated environments and enhance the manoeuverability and flexibility.
基金the National Natural Science Foundation of China(Grant No.U2441263)for financial support of this work。
文摘In composite solid propellants with high aluminum(Al)content and low burning rate,incomplete combustion of the Al powder may occur.In this study,varying lithium(Li)content in Al-Li alloy powder was utilized instead of pure aluminum particles to mitigate agglomeration and enhance the combustion efficiency of solid propellants(Combustion efficiency herein refers to the completeness of metallic fuel oxidation,quantified as the ratio of actual-to-theoretical energy released during combustion)with high Al content and low burning rates.The impact of Al-Li alloy with different Li contents on combustion and agglomeration of solid propellant was investigated using explosion heat,combustion heat,differential thermal analysis(DTA),thermos-gravimetric analysis(TG),dynamic high-pressure combustion test,ignition experiment of small solid rocket motor(SRM)tests,condensation combustion product collection,and X-ray diffraction techniques(XRD).Compared with pure Al,Al-Li alloys exhibit higher combustion heat,which contributes to improved combustion efficiency in Al-Li alloy-containing propellants.DTA and TG analyses demonstrated higher reactivity and lower ignition temperatures for Al-Li alloys.High-pressure combustion experiments at 5 MPa showed that Al-Li alloy fuel significantly decreases combustion agglomeration.The results from theφ75 mm andφ165 mm SRM and XRD tests further support this finding.This study provides novel insights into the combustion and agglomeration behaviors of high-Al,low-burning-rate composite solid propellants and supports the potential application of Al-Li alloys in advanced propellant formulations.
基金supported by the National Natural Science Foundation of China(624B2140).
文摘This paper presents an adaptive formation control method for a heterogeneous robot swarm,utilising a multilevel formation task tree to model various types of formation tasks and a single-state distributed k-winner-take-all(S-DKWTA)algorithm to address the MRTA problem.In addition,we propose an enhanced load reassignment algorithm to resolve conflicts when using S-DKWTA.The S-DKWTA algorithm demonstrates the capability to manage multiple objectives and dynamically select leaders in real-time,thereby optimising formation efficiency and reducing energy consumption.The proposed approach integrates an enhanced artificial potential field(APF)to govern the motion of heterogeneous robot systems which encompasses both unmanned ground vehicles(UGVs)and unmanned aerial vehicles(UAVs),thereby achieving collision and obstacle avoidance.Simulations employing UGVs and UAVs swarm to achieve formation movement demonstrate the efficacy of this approach.The amalgamation of S-DKWTA and improved APF ensures stable and adaptable formation control,underscoring its potential for diverse multirobot applications.
基金supported by the National Natural Science Foundation of China(62333011,62020106003)the Natural Science Foundation of Jiangsu Province of China(BK20222012)+1 种基金the Fundamental Research Funds for the Central Universities(NE2024005)the Postgraduate Research&Practice Innovation Program of Jiangsu Province(KYCX24_0594)。
文摘This paper is concerned with adaptive consensus tracking control of nonlinear multi-agent systems with actuator faults and unknown nonidentical control directions under double semi-Markovian switching topologies.Considering the complex working environment and the stability differences in communication links between leaders and followers,a double semi-Markov process is first introduced to describe the random switching of communication topologies in the leader-follower structure.In order to address challenges from the unknown nonidentical control directions and partial loss of effectiveness actuator faults,a completely independent parameter is introduced into the Nussbaum function to overcome the inherent obstacle of mutual cancellation and avoid the rapid growth rate.Considering only the state information of agents is transmitted among the agents,an adaptive distributed fault-tolerant consensus tracking control is proposed based on the double semi-Markovian switching topologies using the designed Nussbaum function.Furthermore,the stability of the closed-loop nonlinear multi-agent systems is analyzed using contradiction argument and Lyapunov theorem,from which the asymptotic consensus tracking in mean square sense can be obtained.A numerical simulation example is provided to verify the effectiveness of the proposed algorithm.
基金Supported in part by Natural Science Foundation of Guangxi(2023GXNSFAA026246)in part by the Central Government's Guide to Local Science and Technology Development Fund(GuikeZY23055044)in part by the National Natural Science Foundation of China(62363003)。
文摘In this paper,we consider the maximal positive definite solution of the nonlinear matrix equation.By using the idea of Algorithm 2.1 in ZHANG(2013),a new inversion-free method with a stepsize parameter is proposed to obtain the maximal positive definite solution of nonlinear matrix equation X+A^(*)X|^(-α)A=Q with the case 0<α≤1.Based on this method,a new iterative algorithm is developed,and its convergence proof is given.Finally,two numerical examples are provided to show the effectiveness of the proposed method.
基金supported by the National Science Foundation of China(No.62171387)the Science and Technology Program of Sichuan Province(No.2024NSFSC0468)the China Postdoctoral Science Foundation(No.2019M663475).
文摘As an important resource in data link,time slots should be strategically allocated to enhance transmission efficiency and resist eavesdropping,especially considering the tremendous increase in the number of nodes and diverse communication needs.It is crucial to design control sequences with robust randomness and conflict-freeness to properly address differentiated access control in data link.In this paper,we propose a hierarchical access control scheme based on control sequences to achieve high utilization of time slots and differentiated access control.A theoretical bound of the hierarchical control sequence set is derived to characterize the constraints on the parameters of the sequence set.Moreover,two classes of optimal hierarchical control sequence sets satisfying the theoretical bound are constructed,both of which enable the scheme to achieve maximum utilization of time slots.Compared with the fixed time slot allocation scheme,our scheme reduces the symbol error rate by up to 9%,which indicates a significant improvement in anti-interference and eavesdropping capabilities.
