In this paper,dynamic caustic method is applied to analyze the blast-induced crack propagation and distribution of the dynamic stress field around an empty circular hole in polymethyl methacrylate(PMMA)material under ...In this paper,dynamic caustic method is applied to analyze the blast-induced crack propagation and distribution of the dynamic stress field around an empty circular hole in polymethyl methacrylate(PMMA)material under delayed ignition blasting loads.The following experimental results are obtained.(1)In directional-fracture-controlled blasting,the dynamic stress intensity factors(DSIFs)and the propagation paths of the blast-induced cracks are obviously influenced by the delayed ignition.(2) The circular hole situated between the two boreholes poses a strong guiding effect on the coelesence of the cracks,causing them to propagate towards each other when cracks are reaching the circular hole area.(3)Blast-induced cracks are not initiated preferentially because of the superimposed effect from the explosive stress waves on the cracking area.(4) By using the scanning electron microscopy(SEM)method,it is verified that the roughness of crack surfaces changes along the crack propagation paths.展开更多
The dynamic fracture behavior of TA 15ELI alloy with lath-like microstructure was studied by caustics method. Specimens with double-side pre-notch were tested under the plane-stress condition at mode-II loading with a...The dynamic fracture behavior of TA 15ELI alloy with lath-like microstructure was studied by caustics method. Specimens with double-side pre-notch were tested under the plane-stress condition at mode-II loading with a drop hammer system. Caustics information recorded in films illustrated the histories of both crack length and stress intensity factor. The dynamic fracture toughness and crack growth velocity of TA15ELI with lath-like microstructure were determined to be 279 MPa.m1/2 and 32.6 m/s, respectively. SEM fractograph analysis showed a mixed feature of mainly plastic mode for TA 15ELI alloy in dynamic mode-II fracture. Shear localization was observed in the vicinity of the crack initiation area.展开更多
In this paper,the dynamic propagation problem of a mixed-mode crack was studied by means of the experimental method of caustics.The initial curve and caustic equations were derived un- der the mixed-mode dynamic condi...In this paper,the dynamic propagation problem of a mixed-mode crack was studied by means of the experimental method of caustics.The initial curve and caustic equations were derived un- der the mixed-mode dynamic condition.A multi-point measurement method for determining the dy- namic stress intensity factors,K_Ⅰ~d and K_Ⅱ~d,and the position of the crack tip was developed.Several other methods were adopted to check this method,and showed that it has a good precision.Finally, the dynamic propagating process of a mixed-mode crack in a three-point bending beam specimen was investigated with our method.展开更多
基金Supported by the Opening Fund of the State Key Laboratory of Explosion Science and Technology of Beijing Institute of Technology(KFJJ17-01M)
文摘In this paper,dynamic caustic method is applied to analyze the blast-induced crack propagation and distribution of the dynamic stress field around an empty circular hole in polymethyl methacrylate(PMMA)material under delayed ignition blasting loads.The following experimental results are obtained.(1)In directional-fracture-controlled blasting,the dynamic stress intensity factors(DSIFs)and the propagation paths of the blast-induced cracks are obviously influenced by the delayed ignition.(2) The circular hole situated between the two boreholes poses a strong guiding effect on the coelesence of the cracks,causing them to propagate towards each other when cracks are reaching the circular hole area.(3)Blast-induced cracks are not initiated preferentially because of the superimposed effect from the explosive stress waves on the cracking area.(4) By using the scanning electron microscopy(SEM)method,it is verified that the roughness of crack surfaces changes along the crack propagation paths.
文摘The dynamic fracture behavior of TA 15ELI alloy with lath-like microstructure was studied by caustics method. Specimens with double-side pre-notch were tested under the plane-stress condition at mode-II loading with a drop hammer system. Caustics information recorded in films illustrated the histories of both crack length and stress intensity factor. The dynamic fracture toughness and crack growth velocity of TA15ELI with lath-like microstructure were determined to be 279 MPa.m1/2 and 32.6 m/s, respectively. SEM fractograph analysis showed a mixed feature of mainly plastic mode for TA 15ELI alloy in dynamic mode-II fracture. Shear localization was observed in the vicinity of the crack initiation area.
文摘In this paper,the dynamic propagation problem of a mixed-mode crack was studied by means of the experimental method of caustics.The initial curve and caustic equations were derived un- der the mixed-mode dynamic condition.A multi-point measurement method for determining the dy- namic stress intensity factors,K_Ⅰ~d and K_Ⅱ~d,and the position of the crack tip was developed.Several other methods were adopted to check this method,and showed that it has a good precision.Finally, the dynamic propagating process of a mixed-mode crack in a three-point bending beam specimen was investigated with our method.
