The effects of activating fluxes on welding arc were investigated. A special set of water-cooling system and stainless steel were used as parent material. During welding process, high-speed camera system and oscillogr...The effects of activating fluxes on welding arc were investigated. A special set of water-cooling system and stainless steel were used as parent material. During welding process, high-speed camera system and oscillograph were used for capturing instantaneous arc shape and arc voltage respectively. The experimental results indicate that the SiO2 flux can increase the arc voltage, while TiO2 has no this effect on arc voltage. Compared with conventional tungsten inert gas welding (C-TIG), it is found that the arc shape of A-TIG welding used with the SiO2 flux has changed obviously.展开更多
Magnetoelectric （ME） layered Ni/PZT/Ni composites with arc shape have been prepared by using electroless deposition. The ME effect is measured by applying both constant and alternating magnetic fields in longitudina...Magnetoelectric （ME） layered Ni/PZT/Ni composites with arc shape have been prepared by using electroless deposition. The ME effect is measured by applying both constant and alternating magnetic fields in longitudinal and transverse directions. The longitudinal ME voltage coefficient is much larger than the transverse one. With the increase of arc length or decrease of curvature, the resonance frequency of layered arc Ni/PZT/Ni composites gradually decreases, while the maximum of the ME voltage coefficient of the composites increases monotonously. The influence of the arc length and the curvature on ME coupling is discussed. The flat interface between the ferromagnetic and the piezoelectric phases in layered ME composites is believed to provide large ME voltage coefficient.展开更多
In this study,the rotary movement of the tungsten needle in gas tungsten arc welding(GTAW)process was realized by direct current motor.The arc characteristics,the flow of molten pool and the microstructure and propert...In this study,the rotary movement of the tungsten needle in gas tungsten arc welding(GTAW)process was realized by direct current motor.The arc characteristics,the flow of molten pool and the microstructure and properties of the weld bead were studied.The results showed that the rotary motion of the tungsten needle transferred circumferential momentum to the arc as well as the molten pool,thereby conferring the latter with rotating fluid flow characteristics.Under the action of a relatively spiraling shielding gas,arc constriction occurred,and molten pool width dropped considerably.A finer and more uniform precipitated phase in the matrix,as well as a fewer large-medium pores,were achieved in the 5A06 aluminum alloy weld metal using this modified GTAW process,which noticeably increased the bending strength and tensile strength of weld metal and the microhardness of fusion zone.展开更多
The rip currents induced by waves off arc-shaped coastlines are seriously harmful to humans, but understanding of their characteristics is lacking. In this study, the FUNWAVE model was used to calculate the wave-induc...The rip currents induced by waves off arc-shaped coastlines are seriously harmful to humans, but understanding of their characteristics is lacking. In this study, the FUNWAVE model was used to calculate the wave-induced currents in the Haller experiment and the ideal arc-shaped coast similar to Sanya Dadonghai, Hainan Province,China. The results showed that the FUNWAVE model has considerable ability to simulate the rip currents, and it was used to further simulate rip currents off arc-shaped coastlines to investigate their characteristics. The rip currents were found to be stronger as the curvature of arc-shaped coastline increased. Coastal beach slope exerts a significant influence on rip currents; in particular, an overly steep or overly mild slope is not conducive to creating rip currents. Furthermore, the rip currents were found to become weaker as the size of arc-shaped coast decreased. When the height and period of waves increase, the strength of rip currents also increases, and, in some cases, wave heights of 0.4 m may produce dangerous rip currents.展开更多
An analytical method is developed to study the sheltering effects on arc-shaped floating perforated breakwaters. In the process of analysis, the tloating breakwater is assumed to be rigid, thin, vertical, and immovabl...An analytical method is developed to study the sheltering effects on arc-shaped floating perforated breakwaters. In the process of analysis, the tloating breakwater is assumed to be rigid, thin, vertical, and immovable and located in water with constant depth. The fluid domain is divided into two regions by imaginary interface. The velocity potential in each region is expanded by eigenfunction in the context of linear theory. By satisfying continuity of pressure and normal velocity across the imaginary fluid interface, a set of linear algebraic equations can be obtained to determine the unknown coefficients for eigenfunction expansions. The accuracy of the present model was verified by a comparison with existing results for the case of arc-shaped floating breakwater. Numerical results, in the form of contour maps of the non-dimensional wave amplitude around the breakwater and diffracted wave amplitude at typical sections, are presented for a range of wave and breakwater parameters. Results show that the sheltering effects on the arc-shaped floating perforated breakwater are closely related to the incident wavelength, the draft and the porosity of the breakwater.展开更多
Based on the wave radiation and diffraction theory, this paper investigates a new type breakwater with upper arcshaped plate by using the boundary element method(BEM). By comparing with other three designs of plate ty...Based on the wave radiation and diffraction theory, this paper investigates a new type breakwater with upper arcshaped plate by using the boundary element method(BEM). By comparing with other three designs of plate type breakwater(lower arc-shaped plate, single horizontal plate and double horizontal plate), this new type breakwater has been proved more effective. The wave exiting force, transmission and reflection coefficients are analyzed and discussed. In order to reveal the wave elimination mechanism of this type of breakwater, the velocity field around the breakwater is obtained. It is shown that:(1) The sway exciting force is minimal.(2) When the ratio of the submergence and wave amplitude is 0.05, the wave elimination effect will increase by 50% compared with other three types of breakwater.(3) The obvious backflow is found above the plate in the velocity field analysis.展开更多
Compared with the conventional single-roller spinning process, the double-roller clamping spinning（DRCS） process can effectively prevent the sheet metal surface wrinkling and improve the the production efficiency an...Compared with the conventional single-roller spinning process, the double-roller clamping spinning（DRCS） process can effectively prevent the sheet metal surface wrinkling and improve the the production efficiency and the shape precision of final spun part. Based on ABAQUS/Explicit nonlinear finite element software, the finite element model of the multi-pass DRCS for the sheet metal is established, and the material model, the contact definition, the mesh generation, the loading trajectory and other key technical problems are solved. The simulations on the multi-pass DRCS of the ordinary Q235A steel cylindrical part with the arc-shaped surface flange are carried out. The effects of number of spinning passes on the production efficiency, the spinning moment, the shape error of the workpiece, and the wall thickness distribution of the final part are obtained. It is indicated definitely that with the increase of the number of spinning passes the geometrical precision of the spun part increases while the production efficiency reduces. Moreover, the variations of the spinning forces and the distributions of the stresses, strains, wall thickness during the multi-pass DRCS process are revealed. It is indicated that during the DRCS process the radical force is the largest, and the whole deformation area shows the tangential tensile strain and the radial compressive strain, while the thickness strain changes along the generatrix directions from the compressive strain on the outer edge of the flange to the tensile strain on the inner edge of the flange. Based on the G-CNC6135 NC lathe, the three-axis linkage computer-controlled experimental device for DRCS which is driven by the AC servo motor is developed. And then using the experimental device, the Q235A cylindrical parts with the arc-shape surface flange are formed by the DRCS. The simulation results of spun parts have good consistency with the experimental results, which verifies the feasibility of DRCS process and the reliability of the finite element model for DRCS.展开更多
The effects of interface shape on stress wave distribution and attenuation were investiga- ted using finite element method （ FEM ）. The simulation results indicate that when the stress wave propagates from SiC ceram...The effects of interface shape on stress wave distribution and attenuation were investiga- ted using finite element method （ FEM ）. The simulation results indicate that when the stress wave propagates from SiC ceramic to A1 alloy, the tensile stress decreases and the attenuation coefficient of the stress wave increases with increasing central angle of the concave interface between SiC and A1. But for the convex interface, the tensile stress increases and attenuation coefficient decreases with increasing central angle. As the stress wave propagates from A1 alloy to SiC ceramic, the atten- uation coefficient of stress wave decreases with increasing the central angle of the concave interface. For the convex interface, the attenuation coefficient increases with increasing central angle.展开更多
The problem of the hydrodynamic interaction with the arc-shaped bottom-mounted breakwaters is investigated theoretically. The breakwater is assumed to be rigid, thin, impermeable and vertically located in a finite wat...The problem of the hydrodynamic interaction with the arc-shaped bottom-mounted breakwaters is investigated theoretically. The breakwater is assumed to be rigid, thin, impermeable and vertically located in a finite water depth. The fluid domain is divided into two sub-regions of inner and outer by an auxiliary circular interface. Linear theory is assumed and the eigenfunction expansion approach is used to determine the wave field. In order to examine the validity of the theoretical model, the analytical solutions are compared to agree well with published results with the same parameters. Numerical results including wave amplitude, surge pressure, and wave force are presented with different model parameters. The major factors including wave parameters, structure configuration, and water depth that affect the surge pressure, wave forces, and wave amplitudes are discussed and illustrated by some graphs and cloud maps.展开更多
It is of great significance to model the keyhole shape and dimensions to optimize the plasma arc welding process parameters. In this study, through employing a combined volumetric heat source mode, the weld pool in ke...It is of great significance to model the keyhole shape and dimensions to optimize the plasma arc welding process parameters. In this study, through employing a combined volumetric heat source mode, the weld pool in keyhole plasma arc welding is determined firstly, and then the dynamic force-balance condition on the interface between the plasma jet and the molten metal is dealt with in describing the keyhole formation inside the weld pool. The effects of welding current on the shape and size of keyhole are numerically analyzed. The sharp transformation from a partial keyhole to a full-penetration keyhole is quantitatively demonstrated.展开更多
A decagonal quasicrystal, which is weakened by an arc-shaped crackpenetrating through the solid in the period direction, and which is subjected to remote uniformphonon stresses, is investigated by applying the complex...A decagonal quasicrystal, which is weakened by an arc-shaped crackpenetrating through the solid in the period direction, and which is subjected to remote uniformphonon stresses, is investigated by applying the complex variable method which is just developed bythe authors. It is found that the phonon and phason stresses near the crack tips exhibit inversesquare root singularities. The four complex stress functions characterizing the phonon and phasonfields are derived. Explicit expressions for the phonon and phason stress intensity factors, crackopening displacements and energy release rate are also presented.展开更多
In the northern part of the Ordos Basin, there is a 325 km long arc-shaped Langshan uplift and a 15 km-deep Linhe Trench in front of Langshan, which are rare geological phenomena for which origins no one has explained...In the northern part of the Ordos Basin, there is a 325 km long arc-shaped Langshan uplift and a 15 km-deep Linhe Trench in front of Langshan, which are rare geological phenomena for which origins no one has explained. This article comprehensively analyzes the research achievements over the past 40 years of geology, geomorphology, seismic exploration, paleogeography, and oil and gas exploration in the Ordos Basin and Langshan. It recognizes that the northern part of the Ordos Basin experienced a meteorite impact in the Late Cretaceous period. The impact pushed the block northwest ward, subducting after colliding with igneous rocks in the north. This sudden event formed a clear arc-shaped mountain zone in the north and a wedge-shaped trench in front of the mountain. The chaotic layers, prolonged and continuous faults, and numerous thrust layers in the Langshan, a negative anomaly area in the center of the northern Ordos, abnormal orientation of crystalline basement structures in the north of Ordos, Moho uplift, and distribution of meteorite fragments in the northwest of Langshan, all of these geological phenomena support the occurrence of the meteorite impact event, forming the arc-shaped Langshan and the Trench.展开更多
A two-dimensional model was established for the first time by coupling moving wire and arc in CMT-WAAM and GMAWWAAM process,revealing the temperature,potential and droplet transition behavior of droplet metal.The drop...A two-dimensional model was established for the first time by coupling moving wire and arc in CMT-WAAM and GMAWWAAM process,revealing the temperature,potential and droplet transition behavior of droplet metal.The droplet transition and the change of droplet transfer mode under different wire feeding speed were analyzed.The experiments and numerical simulation research found that droplet transition mode is projected transfer in GMAW-WAAM process under 150 A current,with a complete transition period is 14 ms.The droplet transition shows a short-circuit transition mode in CMT-WAAM process,with wire feeding speed of 5.5 m/min and a complete transition period is 20 ms.The droplet transition shows a mixture of droplet transfer and short-circuit transition mode in CMT-WAAM process,with wire feeding speed of 5.5 m/min and a complete transition period is 23 ms.Based on the theoretical research and experimental studies,the mechanism of droplet transfer mode in WAAM was studied,which can provide reference for optimizing parameters.展开更多
Ultrasound-magnetic field coaxial hybrid Gas Tungsten Arc Welding(U-M-GTAW)is proposed as a means to control arc characteristics.The arc characteristics and the mechanism to change them,in an ultrasound-magnetic field...Ultrasound-magnetic field coaxial hybrid Gas Tungsten Arc Welding(U-M-GTAW)is proposed as a means to control arc characteristics.The arc characteristics and the mechanism to change them,in an ultrasound-magnetic field coaxial hybrid GTAW,were studied by both experimental and theoretical analyses.The results showed that a periodic rotation and compression of the arc shape were obtained in U-M-GTAW and the arc energy was also enhanced.The most obvious compression of the arc shape in U-M-GTAW was obtained,compared with GTAW,M-GTAW and U-GTAW.At the same time,a periodic rotation of the arc was observed in U-M-GTAW.The geometric parameters of the arc shape in U-M-GTAW are reduced more than double compared with traditional GTAW.The arc voltage in the hybrid GTAW was increased,especially in the U-M-GTAW.The electromagnetic force and acoustic radiation force were the main factors for the change of arc characteristics in the U-M-GTAW.展开更多
Variable polarity plasma arc-gas metal arc welding(VPPA-GMAW)integrates the advantages of VPPA and GMAW,and it is particularly applied to weld thick-plates aluminum alloys.High-speed camera and data acquisition system...Variable polarity plasma arc-gas metal arc welding(VPPA-GMAW)integrates the advantages of VPPA and GMAW,and it is particularly applied to weld thick-plates aluminum alloys.High-speed camera and data acquisition system were used to analyze the arc shape and the welding process electrical signal.According to the analysis of arc swing amplitude and the approximate entropy of arc voltage signal denoised by wavelet threshold method,the influence of VPPA frequency on the arc stability was studied.The results show that the approximate entropy of GMAW arc voltage decreases with the increase of VPPA frequency in a certain range,and the stability of the hybrid arc is significantly improved.The spectral analysis shows that the arc stability is reduced due to the resonance effect between the VPPA and the GMAW arc when the VPPA frequency closes to the GMAW arc pulse frequency.The results are helpful to understand hybrid welding mechanism and the selection of welding process parameters.展开更多
基金Project(Z2002F03) supported by the Natural Science Foundation of Shandong Province, China
文摘The effects of activating fluxes on welding arc were investigated. A special set of water-cooling system and stainless steel were used as parent material. During welding process, high-speed camera system and oscillograph were used for capturing instantaneous arc shape and arc voltage respectively. The experimental results indicate that the SiO2 flux can increase the arc voltage, while TiO2 has no this effect on arc voltage. Compared with conventional tungsten inert gas welding (C-TIG), it is found that the arc shape of A-TIG welding used with the SiO2 flux has changed obviously.
基金Project supported by the Natural Science Foundation of Jiangsu Province of China (Grant No. BK2010505)the Funding of Jiangsu Innovation Program for Graduate Education (Grant No. CX10B 099Z)
文摘Magnetoelectric （ME） layered Ni/PZT/Ni composites with arc shape have been prepared by using electroless deposition. The ME effect is measured by applying both constant and alternating magnetic fields in longitudinal and transverse directions. The longitudinal ME voltage coefficient is much larger than the transverse one. With the increase of arc length or decrease of curvature, the resonance frequency of layered arc Ni/PZT/Ni composites gradually decreases, while the maximum of the ME voltage coefficient of the composites increases monotonously. The influence of the arc length and the curvature on ME coupling is discussed. The flat interface between the ferromagnetic and the piezoelectric phases in layered ME composites is believed to provide large ME voltage coefficient.
基金supported by National Natural Science Foundation of China(52175305)National Natural Science Foundation of China(U22B20127)Taishan Scholars Project(tstp20230618).
文摘In this study,the rotary movement of the tungsten needle in gas tungsten arc welding(GTAW)process was realized by direct current motor.The arc characteristics,the flow of molten pool and the microstructure and properties of the weld bead were studied.The results showed that the rotary motion of the tungsten needle transferred circumferential momentum to the arc as well as the molten pool,thereby conferring the latter with rotating fluid flow characteristics.Under the action of a relatively spiraling shielding gas,arc constriction occurred,and molten pool width dropped considerably.A finer and more uniform precipitated phase in the matrix,as well as a fewer large-medium pores,were achieved in the 5A06 aluminum alloy weld metal using this modified GTAW process,which noticeably increased the bending strength and tensile strength of weld metal and the microhardness of fusion zone.
基金The National Natural Science Foundation under contract Nos 41206163,41076048 and 41376012the Operation Expenses for Universities'Basic Scientific Research of Central Authorities under contract Nos 2011B05714 and 2014B06514
文摘The rip currents induced by waves off arc-shaped coastlines are seriously harmful to humans, but understanding of their characteristics is lacking. In this study, the FUNWAVE model was used to calculate the wave-induced currents in the Haller experiment and the ideal arc-shaped coast similar to Sanya Dadonghai, Hainan Province,China. The results showed that the FUNWAVE model has considerable ability to simulate the rip currents, and it was used to further simulate rip currents off arc-shaped coastlines to investigate their characteristics. The rip currents were found to be stronger as the curvature of arc-shaped coastline increased. Coastal beach slope exerts a significant influence on rip currents; in particular, an overly steep or overly mild slope is not conducive to creating rip currents. Furthermore, the rip currents were found to become weaker as the size of arc-shaped coast decreased. When the height and period of waves increase, the strength of rip currents also increases, and, in some cases, wave heights of 0.4 m may produce dangerous rip currents.
基金supported by the Natural Science Foundation of Jiangsu Province(Grant No.Bk2006013)the foundation of the State Key Laboratory of Ocean Engineering,Shanghai Jiao Tong University(Grant No.0907)the foundation of Engineering Institute of Engineering Corps and PLA University of Science & Technology
文摘An analytical method is developed to study the sheltering effects on arc-shaped floating perforated breakwaters. In the process of analysis, the tloating breakwater is assumed to be rigid, thin, vertical, and immovable and located in water with constant depth. The fluid domain is divided into two regions by imaginary interface. The velocity potential in each region is expanded by eigenfunction in the context of linear theory. By satisfying continuity of pressure and normal velocity across the imaginary fluid interface, a set of linear algebraic equations can be obtained to determine the unknown coefficients for eigenfunction expansions. The accuracy of the present model was verified by a comparison with existing results for the case of arc-shaped floating breakwater. Numerical results, in the form of contour maps of the non-dimensional wave amplitude around the breakwater and diffracted wave amplitude at typical sections, are presented for a range of wave and breakwater parameters. Results show that the sheltering effects on the arc-shaped floating perforated breakwater are closely related to the incident wavelength, the draft and the porosity of the breakwater.
基金financially supported by the National Key Basic Research Program of China(Grant No.2013CB036101)the National Natural Science Foundation of China(Grant No.11702054)
文摘Based on the wave radiation and diffraction theory, this paper investigates a new type breakwater with upper arcshaped plate by using the boundary element method(BEM). By comparing with other three designs of plate type breakwater(lower arc-shaped plate, single horizontal plate and double horizontal plate), this new type breakwater has been proved more effective. The wave exiting force, transmission and reflection coefficients are analyzed and discussed. In order to reveal the wave elimination mechanism of this type of breakwater, the velocity field around the breakwater is obtained. It is shown that:(1) The sway exciting force is minimal.(2) When the ratio of the submergence and wave amplitude is 0.05, the wave elimination effect will increase by 50% compared with other three types of breakwater.(3) The obvious backflow is found above the plate in the velocity field analysis.
基金supported by National Natural Science Foundation of China(Grant Nos.50905137,50975222)China Postdoctoral Science Foundation(Grant No.2012M521757)Natural Science Foundation of Shaanxi for Youths,China(Grant No.2012JQ7032)
文摘Compared with the conventional single-roller spinning process, the double-roller clamping spinning（DRCS） process can effectively prevent the sheet metal surface wrinkling and improve the the production efficiency and the shape precision of final spun part. Based on ABAQUS/Explicit nonlinear finite element software, the finite element model of the multi-pass DRCS for the sheet metal is established, and the material model, the contact definition, the mesh generation, the loading trajectory and other key technical problems are solved. The simulations on the multi-pass DRCS of the ordinary Q235A steel cylindrical part with the arc-shaped surface flange are carried out. The effects of number of spinning passes on the production efficiency, the spinning moment, the shape error of the workpiece, and the wall thickness distribution of the final part are obtained. It is indicated definitely that with the increase of the number of spinning passes the geometrical precision of the spun part increases while the production efficiency reduces. Moreover, the variations of the spinning forces and the distributions of the stresses, strains, wall thickness during the multi-pass DRCS process are revealed. It is indicated that during the DRCS process the radical force is the largest, and the whole deformation area shows the tangential tensile strain and the radial compressive strain, while the thickness strain changes along the generatrix directions from the compressive strain on the outer edge of the flange to the tensile strain on the inner edge of the flange. Based on the G-CNC6135 NC lathe, the three-axis linkage computer-controlled experimental device for DRCS which is driven by the AC servo motor is developed. And then using the experimental device, the Q235A cylindrical parts with the arc-shape surface flange are formed by the DRCS. The simulation results of spun parts have good consistency with the experimental results, which verifies the feasibility of DRCS process and the reliability of the finite element model for DRCS.
基金Supported by the National Basic Research Program of China("973" Program)(613135)
文摘The effects of interface shape on stress wave distribution and attenuation were investiga- ted using finite element method （ FEM ）. The simulation results indicate that when the stress wave propagates from SiC ceramic to A1 alloy, the tensile stress decreases and the attenuation coefficient of the stress wave increases with increasing central angle of the concave interface between SiC and A1. But for the convex interface, the tensile stress increases and attenuation coefficient decreases with increasing central angle. As the stress wave propagates from A1 alloy to SiC ceramic, the atten- uation coefficient of stress wave decreases with increasing the central angle of the concave interface. For the convex interface, the attenuation coefficient increases with increasing central angle.
基金supported by the Major State Basic Research Development Program of China(973 Program,Grant Nos.2014CB046801 and 2014CB046804)the Foundation of the China Scholarship Council(Grant No.201203170143)
文摘The problem of the hydrodynamic interaction with the arc-shaped bottom-mounted breakwaters is investigated theoretically. The breakwater is assumed to be rigid, thin, impermeable and vertically located in a finite water depth. The fluid domain is divided into two sub-regions of inner and outer by an auxiliary circular interface. Linear theory is assumed and the eigenfunction expansion approach is used to determine the wave field. In order to examine the validity of the theoretical model, the analytical solutions are compared to agree well with published results with the same parameters. Numerical results including wave amplitude, surge pressure, and wave force are presented with different model parameters. The major factors including wave parameters, structure configuration, and water depth that affect the surge pressure, wave forces, and wave amplitudes are discussed and illustrated by some graphs and cloud maps.
文摘It is of great significance to model the keyhole shape and dimensions to optimize the plasma arc welding process parameters. In this study, through employing a combined volumetric heat source mode, the weld pool in keyhole plasma arc welding is determined firstly, and then the dynamic force-balance condition on the interface between the plasma jet and the molten metal is dealt with in describing the keyhole formation inside the weld pool. The effects of welding current on the shape and size of keyhole are numerically analyzed. The sharp transformation from a partial keyhole to a full-penetration keyhole is quantitatively demonstrated.
基金Project supported by the National Excellent Young Scholar Science Fund of China(No.10125209)the Teaching and Research Award Fuud for Outstanding Young Teachers in High Education Institutions of the Ministry of Education of China
文摘A decagonal quasicrystal, which is weakened by an arc-shaped crackpenetrating through the solid in the period direction, and which is subjected to remote uniformphonon stresses, is investigated by applying the complex variable method which is just developed bythe authors. It is found that the phonon and phason stresses near the crack tips exhibit inversesquare root singularities. The four complex stress functions characterizing the phonon and phasonfields are derived. Explicit expressions for the phonon and phason stress intensity factors, crackopening displacements and energy release rate are also presented.
文摘In the northern part of the Ordos Basin, there is a 325 km long arc-shaped Langshan uplift and a 15 km-deep Linhe Trench in front of Langshan, which are rare geological phenomena for which origins no one has explained. This article comprehensively analyzes the research achievements over the past 40 years of geology, geomorphology, seismic exploration, paleogeography, and oil and gas exploration in the Ordos Basin and Langshan. It recognizes that the northern part of the Ordos Basin experienced a meteorite impact in the Late Cretaceous period. The impact pushed the block northwest ward, subducting after colliding with igneous rocks in the north. This sudden event formed a clear arc-shaped mountain zone in the north and a wedge-shaped trench in front of the mountain. The chaotic layers, prolonged and continuous faults, and numerous thrust layers in the Langshan, a negative anomaly area in the center of the northern Ordos, abnormal orientation of crystalline basement structures in the north of Ordos, Moho uplift, and distribution of meteorite fragments in the northwest of Langshan, all of these geological phenomena support the occurrence of the meteorite impact event, forming the arc-shaped Langshan and the Trench.
文摘A two-dimensional model was established for the first time by coupling moving wire and arc in CMT-WAAM and GMAWWAAM process,revealing the temperature,potential and droplet transition behavior of droplet metal.The droplet transition and the change of droplet transfer mode under different wire feeding speed were analyzed.The experiments and numerical simulation research found that droplet transition mode is projected transfer in GMAW-WAAM process under 150 A current,with a complete transition period is 14 ms.The droplet transition shows a short-circuit transition mode in CMT-WAAM process,with wire feeding speed of 5.5 m/min and a complete transition period is 20 ms.The droplet transition shows a mixture of droplet transfer and short-circuit transition mode in CMT-WAAM process,with wire feeding speed of 5.5 m/min and a complete transition period is 23 ms.Based on the theoretical research and experimental studies,the mechanism of droplet transfer mode in WAAM was studied,which can provide reference for optimizing parameters.
基金supported by the Fundamental Research Funds for the Central Universities of China(No.2572021BF02).
文摘Ultrasound-magnetic field coaxial hybrid Gas Tungsten Arc Welding(U-M-GTAW)is proposed as a means to control arc characteristics.The arc characteristics and the mechanism to change them,in an ultrasound-magnetic field coaxial hybrid GTAW,were studied by both experimental and theoretical analyses.The results showed that a periodic rotation and compression of the arc shape were obtained in U-M-GTAW and the arc energy was also enhanced.The most obvious compression of the arc shape in U-M-GTAW was obtained,compared with GTAW,M-GTAW and U-GTAW.At the same time,a periodic rotation of the arc was observed in U-M-GTAW.The geometric parameters of the arc shape in U-M-GTAW are reduced more than double compared with traditional GTAW.The arc voltage in the hybrid GTAW was increased,especially in the U-M-GTAW.The electromagnetic force and acoustic radiation force were the main factors for the change of arc characteristics in the U-M-GTAW.
基金supported by the National Natural Science Foundation of China(51665044)Natural Science Foundation of Inner Mongolia(2019LH05017)+1 种基金Science and Technology Programs of Inner Mongolia(2020GG0313)Major Basic Research Open Subjects of Inner Mongolia Autonomous Region.
文摘Variable polarity plasma arc-gas metal arc welding(VPPA-GMAW)integrates the advantages of VPPA and GMAW,and it is particularly applied to weld thick-plates aluminum alloys.High-speed camera and data acquisition system were used to analyze the arc shape and the welding process electrical signal.According to the analysis of arc swing amplitude and the approximate entropy of arc voltage signal denoised by wavelet threshold method,the influence of VPPA frequency on the arc stability was studied.The results show that the approximate entropy of GMAW arc voltage decreases with the increase of VPPA frequency in a certain range,and the stability of the hybrid arc is significantly improved.The spectral analysis shows that the arc stability is reduced due to the resonance effect between the VPPA and the GMAW arc when the VPPA frequency closes to the GMAW arc pulse frequency.The results are helpful to understand hybrid welding mechanism and the selection of welding process parameters.
