Stall flutter poses great challenges to flight safety.To alleviate this problem,a steady blowing control considering the perturbation and wake-induced vibration at a large angle of attack is developed in this paper,wh...Stall flutter poses great challenges to flight safety.To alleviate this problem,a steady blowing control considering the perturbation and wake-induced vibration at a large angle of attack is developed in this paper,where two blowings are configured on upper and lower tail surfaces to suppress the stall flutter.The stall flutter with one-degree-of-freedom is first evaluated by numerical simulation.The equation of motion for stall flutter is solved by the Newmark-β method.Then,the stall flutter responses for five blowing speeds,i.e.,0,4,12,20,and 28 m/s under the airspeed range of 3–9 m/s,are studied in detail.The stall flutter suppression mechanism can be summarized as follows:a large blowing speed can inject energy into the boundary layer and enhance the high-pressure zone,which delays the flow separation on the suction surface.In this way,the formation of the leading-edge separation vortex is suppressed.Thus,the dynamic stall vortex is weakened and accelerates shedding.In addition,the driving moment is reduced,which leads to a decrement in the stall flutter amplitude.When the blowing speed is 28 m/s(stall flutter amplitude=0.1357 rad),compared with uncontrolled case(stall flutter amplitude=0.6002 rad),the amplitude can decrease by 77.39%,which demonstrates the effectiveness of the proposed steady blowing based active control strategy.展开更多
To improve the vertical axis wind turbine(VAWT)design,the angle of attack(AOA)and airfoil data must be treated correctly.The present paper develops a method for determining AOA on a VAWT based on computational fluid d...To improve the vertical axis wind turbine(VAWT)design,the angle of attack(AOA)and airfoil data must be treated correctly.The present paper develops a method for determining AOA on a VAWT based on computational fluid dynamics(CFD)analysis.First,a CFD analysis of a two-bladed VAWT equipped with a NACA 0012 airfoil is conducted.The thrust and power coefficients are validated through experiments.Second,the blade force and velocity data at monitoring points are collected.The AOA at different azimuth angles is determined by removing the blade self-induction at the monitoring point.Then,the lift and drag coefficients as a function of AOA are extracted.Results show that this method is independent of the monitoring points selection located at certain distance to the blades and the extracted dynamic stall hysteresis is more precise than the one with the“usual”method without considering the self-induction from bound vortices.展开更多
Angle of Attack(AOA) is a crucial parameter which directly affects the aerodynamic forces of an aircraft.The measurement of AOA is required to ensure a safe flight within its designed flight envelop.This paper intends...Angle of Attack(AOA) is a crucial parameter which directly affects the aerodynamic forces of an aircraft.The measurement of AOA is required to ensure a safe flight within its designed flight envelop.This paper intends to summarise a comprehensive survey on the measurement techniques and estimation methods for AOA, specifically in Unmanned Aerial Vehicle(UAV) applications.In the case of UAVs, weight constraint plays a major role as far as sensor suites are concerned.This results in selecting a suitable estimation method to extract AOA using the available data from the autopilot.The most feasible and widely employed AOA measurement technique is by using the Multi-Hole Probes(MHPs).The MHP measures the AOA regarding the pressure variations between the ports.Due to the importance of MHP in AOA measurement, the calibration methods for the MHP are also included in this paper.This paper discusses the AOA measurement using virtual AOA sensors, their importance and the operation.展开更多
The studies of asymmetric vortices flow over slender body and its active control at high angles of attack have significant importance for both academic field and engineering area.This paper attempts to provide an upda...The studies of asymmetric vortices flow over slender body and its active control at high angles of attack have significant importance for both academic field and engineering area.This paper attempts to provide an update state of art to the investigations on the fields of forebody asymmetric vortices.This review emphasizes the correlation between micro-perturbation on the model nose and its response and evolution behaviors of the asymmetric vortices.The critical issues are discussed, which include the formation and evolution mechanism of asymmetric multi-vortices;main behaviors of asymmetric vortices flow including its deterministic feature and vortices flow structure;the evolution and development of asymmetric vortices under the perturbation on the model nose;forebody vortex active control especially discussed micro-perturbation active control concept and technique in more detail.However present understanding in this area is still very limited and this paper tries to identify the key unknown problems in the concluding remarks.展开更多
A formal analysis to footprint problem with effects of angle of attack （AOA） is presented. First a flexible and rapid standardized method for footprint generation is developed. Zero bank angle control strategy and t...A formal analysis to footprint problem with effects of angle of attack （AOA） is presented. First a flexible and rapid standardized method for footprint generation is developed. Zero bank angle control strategy and the maximum crossrange method are used to obtain virtual target set; afterward, closed-loop bank angle guidance law is used to find footprint by solving closest approach problem for each element in virtual target set. Then based on quasi-equilibrium glide condition, the typical inequality reentry trajectory constraints are converted to angle of attack lower boundary constraint. Constrained by the lower boundary, an original and practical angle of attack parametric method is proposed. By using parametric angle of attack profile, optimization algorithm for angle of attack is designed and the impact of angle of attack to footprint is discussed. Simulations with different angle of attack profiles are presented to demonstrate the performance of the proposed footprint solution method and validity of optimal algorithm.展开更多
To investigate the longitudinal motion stability of aircraft maneuvers conveniently, a new stability analysis approach is presented in this paper. Based on describing longitudinal aerodynamics at high angle-of-attack ...To investigate the longitudinal motion stability of aircraft maneuvers conveniently, a new stability analysis approach is presented in this paper. Based on describing longitudinal aerodynamics at high angle-of-attack （a ＆lt; 50 ） motion by polynomials, a union structure of two-order differential equation is suggested. By means of nonlinear theory and method, analytical and global bifurcation analyses of the polynomial differential systems are provided for the study of the nonlinear phenomena of high angle-of-attack flight. Applying the theories of bifurcations, many kinds of bifurcations, such as equilibrium, Hopf, homoclinic （heteroclinic） orbit and double limit cycle bifurcations are discussed and the existence conditions for these bifurcations as well as formulas for calculating bifurcation curves are derived. The bifurcation curves divide the parameter plane into several regions; moreover, the complete bifurcation diagrams and phase portraits in different regions are obtained. Finally, our conclusions are applied to analyzing the stability and bifurcations of a practical example of a high angle-of-attack flight as well as the effects of elevator deflection on the asymptotic stability regions of equilibrium. The model and analytical methods presented in this paper can be used to study the nonlinear flight dynamic of longitudinal stall at high angle of attack.展开更多
The wind tunnel experiments is conducted to get inspiration for understanding the mechanism of the asymmetric flow pattern and developing an innovative flow control technique for a slender body at high angle of attack...The wind tunnel experiments is conducted to get inspiration for understanding the mechanism of the asymmetric flow pattern and developing an innovative flow control technique for a slender body at high angle of attack. The bi-stable situation of the side forces is observed, which could be easily switched by a tiny disturbances either from coming flow or from artificial disturbances at nose tip （including manufacturing defect）. In turbulent flows the side forces switched randomly between positive and negative. There exists a hysteresis loop of side force with the rolling angle. A rod in front of the slender body is used to change the vortex pattern, which could be kept even the rod is moved out from the stream. A miniature strake attached to the nose tip of the model can be moved to different circumferential position. When the strake is stationary, the hysteresis loop disappears and the side force does not change with the turbulent fluctuation of coming flow. The results from dynamic measurements of section side force indicates that when the strake swung at lower frequency the side force can follow the cadence of the swinging strake. With increasing frequency, the magnitude of the side force decreases. At still high frequency, the side force diminishes to zero. If the strake is swinging, while the middle position can be changed to different circumferential angle Фs on either left or right side, the side forces can be changed proportionally with the angle Фs. On the basis of the experimental results, the mechanism of the asymmetry is discussed.展开更多
Flying condition with angle of attack is inevitable in a hypersonic vehicle,and it may influence the thermal protection system(TPS)performance of opposing jet and its combinations.A 3D Navier–Stokes equation and shea...Flying condition with angle of attack is inevitable in a hypersonic vehicle,and it may influence the thermal protection system(TPS)performance of opposing jet and its combinations.A 3D Navier–Stokes equation and shear stress transfer(SST)k-ωmodel with compressible correction are employed to simulate the angle of attack characteristics of a blunt body with opposing jet and platelet transpiration TPS.The flowfield and heat flux transfer for angles of attack 0°,3°,6°with jet pressure ratio PR=0.1 and 0°,6°,12°with PR=0.2 are obtained.Numerical results show that the flowfield is no longer symmetrical with the effect of the angle of attack.The flowfield and heat transfer in windward and leeward performed adversely.The recompression shock wave in windward is strengthened,which increases local temperature and strengthens heat transfer.The opposing jet fails in thermal protection when the angle of attack reaches critical value;however,the critical angle of attack can be promoted by increasing PR.Finally,the transpiration gas can strengthen the cooling efficiency of windward,thereby,increasing the critical angle of attack.展开更多
In this paper, fast setpoint altitude tracking control for Hypersonic Flight Vehicle(HFV)satisfying Angle of Attack(AOA) constraint is studied with a two-loop structure controller, in the presence of parameter uncerta...In this paper, fast setpoint altitude tracking control for Hypersonic Flight Vehicle(HFV)satisfying Angle of Attack(AOA) constraint is studied with a two-loop structure controller, in the presence of parameter uncertainties and disturbances. For the outer loop, phase plane design is adopted for the simplified model under Bang-Bang controller to generate AOA command guaranteeing fast tracking performance. Modifications based on Feedback-Linearization(FL) technique are adopted to transform the phase trajectory into a sliding curve. Moreover, to resist mismatch between design model and actual model, Fast Exponential Reaching Law(FERL) is augmented with the baseline controller to maintain state on the sliding curve. The inner-loop controller is based on backstepping technique to track the AOA command generated by outer-loop controller. Barrier Lyapunov Function(BLF) design is employed to satisfy AOA requirement. Moreover, a novel auxiliary state is introduced to remove the restriction of BLF design on initial tracking errors. Dynamic Surface Control(DSC) is utilized to ease the computation burden. Rigorous stability proof is then given, and AOA is guaranteed to stay in predefined region theoretically. Simulations are conducted to verify the efficiency and superior performance of the proposed method.展开更多
Impulsively starting flow, by a sudden attainment of a large angle of attack, has been well studied for incompressible and supersonic flows, but less studied for subsonic flow. Recently,a preliminary numerical study f...Impulsively starting flow, by a sudden attainment of a large angle of attack, has been well studied for incompressible and supersonic flows, but less studied for subsonic flow. Recently,a preliminary numerical study for subsonic starting flow at a high angle of attack displays an advance of stall around a Mach number of 0.5, when compared to other Mach numbers. To see what happens in this special case, we conduct here in this paper a further study for this case, to display and analyze the full flow structures. We find that for a Mach number around 0.5, a local supersonic flow region repeatedly splits and merges, and a pair of left-going and right-going unsteady shock waves are embedded inside the leading edge vortex once it is sufficiently grown up and detached from the leading edge. The flow evolution during the formation of shock waves is displayed in detail. The reason for the formation of these shock waves is explained here using the Laval nozzle flow theory. The existence of this shock pair inside the vortex, for a Mach number only close to 0.5, may help the growing of the trailing edge vortex responsible for the advance of stall observed previously.展开更多
Firstly, the steady laminar flow field of a hypersonic sharp cone boundary layer with zero angle of attack was computed. Then, two groups of finite amplitude T-S wave disturbances were introduced at the entrance of th...Firstly, the steady laminar flow field of a hypersonic sharp cone boundary layer with zero angle of attack was computed. Then, two groups of finite amplitude T-S wave disturbances were introduced at the entrance of the computational field, and the spatial mode transition process was studied by direct numerical simulation （DNS） method. The mechanism of the transition process was analyzed. It was found that the change of the stability characteristics of the mean flow profile was the key issue. Furthermore, the characteristics of evolution for the disturbances of different modes in the hypersonic sharp cone boundary layer were discussed.展开更多
To reduce the propulsion system installation thrust loss under high angle of attack maneuvering,a control method based on real-time optimization of the integrated aeropropulsion is proposed.Firstly,based on data fitti...To reduce the propulsion system installation thrust loss under high angle of attack maneuvering,a control method based on real-time optimization of the integrated aeropropulsion is proposed.Firstly,based on data fitting and physical principle,an integrated onboard model of propulsion system is established,which can calculate various performance parameters of the propulsion system in real time,and has high accuracy and real-time performance.Secondly,to improve the compatibility of optimization real-time performance and search accuracy,the online optimization control of aero-propulsion system is realized based on an improved trust region algorithm.Finally,by controlling the auxiliary intake valve,a good match between inlet and engine is realized,which solves the problems of intake flow reducing and total pressure recovery coefficient declining,and improves the installation performance of propulsion system.The simulation results indicate that,compared with the conventional independent engine control,the real-time integrated optimization method reduces the installed thrust loss by 3.61%under the design condition,and 4.58%under the off-design condition.Furthermore,the simulation on HIL(Hardware-In-theLoop)platform verifies the real-time performance of integrated optimization method.展开更多
The high-frequency instability on a cone at 6°angle of attack is measured in a hypersonic quiet wind tunnel with Reynolds number of 6.90×10^(6)m^(−1),and Mach number is 6.Fast-response pressure sensors are u...The high-frequency instability on a cone at 6°angle of attack is measured in a hypersonic quiet wind tunnel with Reynolds number of 6.90×10^(6)m^(−1),and Mach number is 6.Fast-response pressure sensors are used to measure the disturbance waves on the surface of the cone.The nano-tracer-based planar laser scattering(NPLS)technique is used to visualize the coherent structures of the three-dimensional boundary layer.At the plane of azimuthal angle ofθ=30°from the leeward ray,low-and high-frequency disturbance waves with the characteristic frequency of f=10–20 kHz and f=120–140 kHz are detected.From the NPLS image,the regular large-scale traveling crossflow waves structures are observed,which are related to the low-frequency instability.On the top of the traveling crossflow waves,there are a series of small-scale structures,which suggests there is strong shear on the top of the traveling crossflow waves.These small vortices likely are the secondary instability of the traveling crossflow waves,which are associated with the high-frequency instability.The disturbance waves characteristics in different planes are measured using PCB transducers.The result shows that the high-frequency instability occurs in the planes ofθ=15°-60°,and the characteristic frequency is between f=106.97-181.08 kHz.With the increase of azimuthal angle,the characteristic frequency increases obviously,which is related to the thinner boundary layer near the windward side.With the increase of the x-coordinate,the circumferential range of the high-frequency instability gradually widens.展开更多
Angle of attack and lateral force are two important parameters influencing wheel rail wear. This paper deals with the question of influences of the angle of attack and the lateral force on the wear of rail. A series ...Angle of attack and lateral force are two important parameters influencing wheel rail wear. This paper deals with the question of influences of the angle of attack and the lateral force on the wear of rail. A series of experiments are conducted on 1/4 JD 1 Wheel/Rail Tribology Simulation Facility. The angles of attack selected in the tests are 0°16′30″, 0°37′40″ and 1°0′0″ respectively. The lateral forces selected in the tests are 0.694 kN, 1.250 kN and 2.083 kN, respectively corresponding to the lateral forces of 25 kN, 45 kN and 75 kN measured in the field, with the aim of keeping the same ratio of L/V between laboratory and field conditions. It is found that the larger the angle of attack is, the more serious the wear of rail is. The relation of rail wear rate versus angle of attack is non linear, and the relation of rail wear rate versus lateral force is approximately linear. The influence of angle of attack is more serious than that of lateral force. For the tractive wheelset, the wear index involving linear and quadratic function terms of angle of attack has good agreement with the limited experimental data. Some conclusions are given.展开更多
Unsteady aerodynamic characteristics at high angles of attack are of great importance to the design and development of advanced fighter aircraft, which are characterized by post-stall maneuverability with multiple Deg...Unsteady aerodynamic characteristics at high angles of attack are of great importance to the design and development of advanced fighter aircraft, which are characterized by post-stall maneuverability with multiple Degrees-of-Freedom(multi-DOF) and complex flow field structure.In this paper, a special kind of cable-driven parallel mechanism is firstly utilized as a new suspension method to conduct unsteady dynamic wind tunnel tests at high angles of attack, thereby providing experimental aerodynamic data. These tests include a wide range of multi-DOF coupled oscillatory motions with various amplitudes and frequencies. Then, for aerodynamic modeling and analysis, a novel data-driven Feature-Level Attention Recurrent neural network(FLAR) is proposed. This model incorporates a specially designed feature-level attention module that focuses on the state variables affecting the aerodynamic coefficients, thereby enhancing the physical interpretability of the aerodynamic model. Subsequently, spin maneuver simulations, using a mathematical model as the baseline, are conducted to validate the effectiveness of the FLAR. Finally, the results on wind tunnel data reveal that the FLAR accurately predicts aerodynamic coefficients, and observations through the visualization of attention scores identify the key state variables that affect the aerodynamic coefficients. It is concluded that the proposed FLAR enhances the interpretability of the aerodynamic model while achieving good prediction accuracy and generalization capability for multi-DOF coupling motion at high angles of attack.展开更多
Modeling of unsteady aerodynamic loads at high angles of attack using a small amount of experimental or simulation data to construct predictive models for unknown states can greatly improve the efficiency of aircraft ...Modeling of unsteady aerodynamic loads at high angles of attack using a small amount of experimental or simulation data to construct predictive models for unknown states can greatly improve the efficiency of aircraft unsteady aerodynamic design and flight dynamics analysis.In this paper,aiming at the problems of poor generalization of traditional aerodynamic models and intelligent models,an intelligent aerodynamic modeling method based on gated neural units is proposed.The time memory characteristics of the gated neural unit is fully utilized,thus the nonlinear flow field characterization ability of the learning and training process is enhanced,and the generalization ability of the whole prediction model is improved.The prediction and verification of the model are carried out under the maneuvering flight condition of NACA0015 airfoil.The results show that the model has good adaptability.In the interpolation prediction,the maximum prediction error of the lift and drag coefficients and the moment coefficient does not exceed 10%,which can basically represent the variation characteristics of the entire flow field.In the construction of extrapolation models,the training model based on the strong nonlinear data has good accuracy for weak nonlinear prediction.Furthermore,the error is larger,even exceeding 20%,which indicates that the extrapolation and generalization capabilities need to be further optimized by integrating physical models.Compared with the conventional state space equation model,the proposed method can improve the extrapolation accuracy and efficiency by 78%and 60%,respectively,which demonstrates the applied potential of this method in aerodynamic modeling.展开更多
Abstract Accurate aerodynamic models are the basis of flight simulation and control law design. Mathematically modeling unsteady aerodynamics at high angles of attack bears great difficulties in model structure determ...Abstract Accurate aerodynamic models are the basis of flight simulation and control law design. Mathematically modeling unsteady aerodynamics at high angles of attack bears great difficulties in model structure determination and parameter estimation due to little understanding of the flow mechanism. Support vector machines （SVMs） based on statistical learning theory provide a novel tool for nonlinear system modeling. The work presented here examines the feasibility of applying SVMs to high angle.-of-attack unsteady aerodynamic modeling field. Mainly, after a review of SVMs, several issues associated with unsteady aerodynamic modeling by use of SVMs are discussed in detail, such as sele, ction of input variables, selection of output variables and determination of SVM parameters. The least squares SVM （LS-SVM） models are set up from certain dynamic wind tunnel test data of a delta wing and an aircraft configuration, and then used to predict the aerodynamic responses in other tests. The predictions are in good agreement with the test data, which indicates the satisfving learning and generalization performance of LS-SVMs.展开更多
The high angle of attack characteristics play an important role in the aerodynamic performances of the hypersonic space vehicle. The three-dimensional Reynolds Averaged Navier-Stokes (RANS) equations and the two-equat...The high angle of attack characteristics play an important role in the aerodynamic performances of the hypersonic space vehicle. The three-dimensional Reynolds Averaged Navier-Stokes (RANS) equations and the two-equation RNG k-? turbulence model have been employed to investigate the influence of the high angle of attack on the lift-to-drag ratio and the flow field characteristics of the hypersonic space vehicle, and the contributions of each component to the aerodynamic forces of the vehicle have been discussed as well. At the same time, in order to validate the numerical method, the predicted results have been compared with the available experimental data of a hypersonic slender vehicle, and the grid independency has been analyzed. The obtained results show that the predicted lift-to-drag ratio and pitching moment coefficient show very good agreement with the experimental data in the open literature, and the grid system makes only a slight difference to the numerical results. There exists an optimal angle of attack for the aerodynamic performance of the hypersonic space vehicle, and its value is 20°. When the angle of attack is 20°, the high pressure does not leak from around the leading edge to the upper surface. With the further increasing of the angle of attack, the high pressure spreads from the wing tips to the central area of the vehicle, and overflows from the leading edge again. Further, the head plays an important role in the drag performance of the vehicle, and the lift percentage of the flaperon is larger than that of the rudderevator. This illustrates that the optimization of the flaperon configuration is a great work for the improvement of the aerodynamic performance of the hypersonic space vehicle, especially for a high lift-to-drag ratio.展开更多
A wavecatcher type scramjet intake,that reduces the Mach number number from 4 to 1.552,is used as the basis for a study of flow starting/unstarting as affected by freestream angles of attack and sideslip.The intake de...A wavecatcher type scramjet intake,that reduces the Mach number number from 4 to 1.552,is used as the basis for a study of flow starting/unstarting as affected by freestream angles of attack and sideslip.The intake design is based on a morphed streamtube consisting of two conical flow streamlines using streamline tracing and osculating axisymmetric design theory.Intake flow and performance is modeled using the numerical CFD code and the k-e turbulence model.The intake unstarts at a sideslip angle of 2,a positive angle of attack of 1.Both positive angle of attack and sideslip angle have an adverse effect on the startability of the MBus intake.At negative angles,the intake initially unstarts at5angle of attack,due to the thickened shear layer induced by the streamwise vortex.Then it re-starts at8angle of attack,mainly due to the expansion fan formed at the leading edge,causing the shock wave structures inside the intake to be reestablished.展开更多
The modern high performance air vehicles are required to have extreme maneuverability,which includes the ability of controlled maneuvers at high angle of attack. However, the nonlinear and unsteady aerodynamic phenome...The modern high performance air vehicles are required to have extreme maneuverability,which includes the ability of controlled maneuvers at high angle of attack. However, the nonlinear and unsteady aerodynamic phenomena, such as flow separation, vortices interaction, and vortices breaking down, will occur during the flight at high angle of attack, which could induce the uncommanded motions for the air vehicles. For the high maneuverable and agile air missile, the nonlinear roll motions would occur at the high angle of attack. The present work is focused on the selfinduced nonlinear roll motion for a missile configuration and discusses the influence of the strake wings on the roll motion according to the results from free-to-roll test and PIV measurement using the models assembled with different strake wings at a = 60°. The free-to-roll results show that the model with whole strake wings(baseline), the model assembled with three strake wings(Case A)and the model assembled with two opposite strake wings(Case C) experience the spinning, while the model assembled with two adjacent strake wings(Case B), the model assembled with one strake wing(Case D) and the model with no strake wing(Case E) trim or slightly vibrate at a certain "×"rolling angle, which mean that the rolling stability can be improved by dismantling certain strake wings. The flow field results from PIV measurement show that the leeward asymmetric vortices are induced by the windward strake wings. The vortices would interact the strake wings and induce crossflow on the downstream fins to degrade the rolling stability of the model. This could be the main reason for the self-induced roll motion of the model at a = 60°.展开更多
基金co-supported by the National Natural Science Foundation of China(Nos.52472394,52425211,52201327,52272360)。
文摘Stall flutter poses great challenges to flight safety.To alleviate this problem,a steady blowing control considering the perturbation and wake-induced vibration at a large angle of attack is developed in this paper,where two blowings are configured on upper and lower tail surfaces to suppress the stall flutter.The stall flutter with one-degree-of-freedom is first evaluated by numerical simulation.The equation of motion for stall flutter is solved by the Newmark-β method.Then,the stall flutter responses for five blowing speeds,i.e.,0,4,12,20,and 28 m/s under the airspeed range of 3–9 m/s,are studied in detail.The stall flutter suppression mechanism can be summarized as follows:a large blowing speed can inject energy into the boundary layer and enhance the high-pressure zone,which delays the flow separation on the suction surface.In this way,the formation of the leading-edge separation vortex is suppressed.Thus,the dynamic stall vortex is weakened and accelerates shedding.In addition,the driving moment is reduced,which leads to a decrement in the stall flutter amplitude.When the blowing speed is 28 m/s(stall flutter amplitude=0.1357 rad),compared with uncontrolled case(stall flutter amplitude=0.6002 rad),the amplitude can decrease by 77.39%,which demonstrates the effectiveness of the proposed steady blowing based active control strategy.
文摘To improve the vertical axis wind turbine(VAWT)design,the angle of attack(AOA)and airfoil data must be treated correctly.The present paper develops a method for determining AOA on a VAWT based on computational fluid dynamics(CFD)analysis.First,a CFD analysis of a two-bladed VAWT equipped with a NACA 0012 airfoil is conducted.The thrust and power coefficients are validated through experiments.Second,the blade force and velocity data at monitoring points are collected.The AOA at different azimuth angles is determined by removing the blade self-induction at the monitoring point.Then,the lift and drag coefficients as a function of AOA are extracted.Results show that this method is independent of the monitoring points selection located at certain distance to the blades and the extracted dynamic stall hysteresis is more precise than the one with the“usual”method without considering the self-induction from bound vortices.
基金the financial support of the Aeronautical Research&Development Board(AR&DB)through the SIGMA Panel for sanctioning the project ID number ARDB/01/2021791/M/I。
文摘Angle of Attack(AOA) is a crucial parameter which directly affects the aerodynamic forces of an aircraft.The measurement of AOA is required to ensure a safe flight within its designed flight envelop.This paper intends to summarise a comprehensive survey on the measurement techniques and estimation methods for AOA, specifically in Unmanned Aerial Vehicle(UAV) applications.In the case of UAVs, weight constraint plays a major role as far as sensor suites are concerned.This results in selecting a suitable estimation method to extract AOA using the available data from the autopilot.The most feasible and widely employed AOA measurement technique is by using the Multi-Hole Probes(MHPs).The MHP measures the AOA regarding the pressure variations between the ports.Due to the importance of MHP in AOA measurement, the calibration methods for the MHP are also included in this paper.This paper discusses the AOA measurement using virtual AOA sensors, their importance and the operation.
基金The project supported by the National Natural Science Foundation of China(10172017)Aeronautical Science Foundation of China(02A51048)Foundation of National Key Laboratory of Aerodynamic Design and Research(51462020504HK0101)
文摘The studies of asymmetric vortices flow over slender body and its active control at high angles of attack have significant importance for both academic field and engineering area.This paper attempts to provide an update state of art to the investigations on the fields of forebody asymmetric vortices.This review emphasizes the correlation between micro-perturbation on the model nose and its response and evolution behaviors of the asymmetric vortices.The critical issues are discussed, which include the formation and evolution mechanism of asymmetric multi-vortices;main behaviors of asymmetric vortices flow including its deterministic feature and vortices flow structure;the evolution and development of asymmetric vortices under the perturbation on the model nose;forebody vortex active control especially discussed micro-perturbation active control concept and technique in more detail.However present understanding in this area is still very limited and this paper tries to identify the key unknown problems in the concluding remarks.
基金National Natural Science Foundation of China (61174221)
文摘A formal analysis to footprint problem with effects of angle of attack （AOA） is presented. First a flexible and rapid standardized method for footprint generation is developed. Zero bank angle control strategy and the maximum crossrange method are used to obtain virtual target set; afterward, closed-loop bank angle guidance law is used to find footprint by solving closest approach problem for each element in virtual target set. Then based on quasi-equilibrium glide condition, the typical inequality reentry trajectory constraints are converted to angle of attack lower boundary constraint. Constrained by the lower boundary, an original and practical angle of attack parametric method is proposed. By using parametric angle of attack profile, optimization algorithm for angle of attack is designed and the impact of angle of attack to footprint is discussed. Simulations with different angle of attack profiles are presented to demonstrate the performance of the proposed footprint solution method and validity of optimal algorithm.
基金supported by National Natural Science Foundation of China (No. 61134004)
文摘To investigate the longitudinal motion stability of aircraft maneuvers conveniently, a new stability analysis approach is presented in this paper. Based on describing longitudinal aerodynamics at high angle-of-attack （a ＆lt; 50 ） motion by polynomials, a union structure of two-order differential equation is suggested. By means of nonlinear theory and method, analytical and global bifurcation analyses of the polynomial differential systems are provided for the study of the nonlinear phenomena of high angle-of-attack flight. Applying the theories of bifurcations, many kinds of bifurcations, such as equilibrium, Hopf, homoclinic （heteroclinic） orbit and double limit cycle bifurcations are discussed and the existence conditions for these bifurcations as well as formulas for calculating bifurcation curves are derived. The bifurcation curves divide the parameter plane into several regions; moreover, the complete bifurcation diagrams and phase portraits in different regions are obtained. Finally, our conclusions are applied to analyzing the stability and bifurcations of a practical example of a high angle-of-attack flight as well as the effects of elevator deflection on the asymptotic stability regions of equilibrium. The model and analytical methods presented in this paper can be used to study the nonlinear flight dynamic of longitudinal stall at high angle of attack.
文摘The wind tunnel experiments is conducted to get inspiration for understanding the mechanism of the asymmetric flow pattern and developing an innovative flow control technique for a slender body at high angle of attack. The bi-stable situation of the side forces is observed, which could be easily switched by a tiny disturbances either from coming flow or from artificial disturbances at nose tip （including manufacturing defect）. In turbulent flows the side forces switched randomly between positive and negative. There exists a hysteresis loop of side force with the rolling angle. A rod in front of the slender body is used to change the vortex pattern, which could be kept even the rod is moved out from the stream. A miniature strake attached to the nose tip of the model can be moved to different circumferential position. When the strake is stationary, the hysteresis loop disappears and the side force does not change with the turbulent fluctuation of coming flow. The results from dynamic measurements of section side force indicates that when the strake swung at lower frequency the side force can follow the cadence of the swinging strake. With increasing frequency, the magnitude of the side force decreases. At still high frequency, the side force diminishes to zero. If the strake is swinging, while the middle position can be changed to different circumferential angle Фs on either left or right side, the side forces can be changed proportionally with the angle Фs. On the basis of the experimental results, the mechanism of the asymmetry is discussed.
文摘Flying condition with angle of attack is inevitable in a hypersonic vehicle,and it may influence the thermal protection system(TPS)performance of opposing jet and its combinations.A 3D Navier–Stokes equation and shear stress transfer(SST)k-ωmodel with compressible correction are employed to simulate the angle of attack characteristics of a blunt body with opposing jet and platelet transpiration TPS.The flowfield and heat flux transfer for angles of attack 0°,3°,6°with jet pressure ratio PR=0.1 and 0°,6°,12°with PR=0.2 are obtained.Numerical results show that the flowfield is no longer symmetrical with the effect of the angle of attack.The flowfield and heat transfer in windward and leeward performed adversely.The recompression shock wave in windward is strengthened,which increases local temperature and strengthens heat transfer.The opposing jet fails in thermal protection when the angle of attack reaches critical value;however,the critical angle of attack can be promoted by increasing PR.Finally,the transpiration gas can strengthen the cooling efficiency of windward,thereby,increasing the critical angle of attack.
基金supported by the National Natural Science Foundation of China (Nos. 61833016, 61873295, 61622308and 61933010)。
文摘In this paper, fast setpoint altitude tracking control for Hypersonic Flight Vehicle(HFV)satisfying Angle of Attack(AOA) constraint is studied with a two-loop structure controller, in the presence of parameter uncertainties and disturbances. For the outer loop, phase plane design is adopted for the simplified model under Bang-Bang controller to generate AOA command guaranteeing fast tracking performance. Modifications based on Feedback-Linearization(FL) technique are adopted to transform the phase trajectory into a sliding curve. Moreover, to resist mismatch between design model and actual model, Fast Exponential Reaching Law(FERL) is augmented with the baseline controller to maintain state on the sliding curve. The inner-loop controller is based on backstepping technique to track the AOA command generated by outer-loop controller. Barrier Lyapunov Function(BLF) design is employed to satisfy AOA requirement. Moreover, a novel auxiliary state is introduced to remove the restriction of BLF design on initial tracking errors. Dynamic Surface Control(DSC) is utilized to ease the computation burden. Rigorous stability proof is then given, and AOA is guaranteed to stay in predefined region theoretically. Simulations are conducted to verify the efficiency and superior performance of the proposed method.
基金supported by the National Natural Science Foundation of China(No.11472157)
文摘Impulsively starting flow, by a sudden attainment of a large angle of attack, has been well studied for incompressible and supersonic flows, but less studied for subsonic flow. Recently,a preliminary numerical study for subsonic starting flow at a high angle of attack displays an advance of stall around a Mach number of 0.5, when compared to other Mach numbers. To see what happens in this special case, we conduct here in this paper a further study for this case, to display and analyze the full flow structures. We find that for a Mach number around 0.5, a local supersonic flow region repeatedly splits and merges, and a pair of left-going and right-going unsteady shock waves are embedded inside the leading edge vortex once it is sufficiently grown up and detached from the leading edge. The flow evolution during the formation of shock waves is displayed in detail. The reason for the formation of these shock waves is explained here using the Laval nozzle flow theory. The existence of this shock pair inside the vortex, for a Mach number only close to 0.5, may help the growing of the trailing edge vortex responsible for the advance of stall observed previously.
基金Project supported by the National Natural Science Foundation of China (Key Program) (No.10632050)
文摘Firstly, the steady laminar flow field of a hypersonic sharp cone boundary layer with zero angle of attack was computed. Then, two groups of finite amplitude T-S wave disturbances were introduced at the entrance of the computational field, and the spatial mode transition process was studied by direct numerical simulation （DNS） method. The mechanism of the transition process was analyzed. It was found that the change of the stability characteristics of the mean flow profile was the key issue. Furthermore, the characteristics of evolution for the disturbances of different modes in the hypersonic sharp cone boundary layer were discussed.
基金supported in part by the National Natural Science Foundation of China (Nos. 51906102 and 52176009)the National Science and Technology Major Project, China (Nos. J2019-II-0009-0053, J2019-I-0020-0019 and 2019III-0014-0058)+2 种基金the Innovation Centre for Advanced Aviation Power, China (Nos. HKCX2020-02-022 and HKCX2020-02-027)the Research on the Basic Problem of Intelligent Aero-engine, China (No. 2017-JCJQZD-047-21)the Fundamental Research Funds for the Central Universities, China (No. NZ2020002)
文摘To reduce the propulsion system installation thrust loss under high angle of attack maneuvering,a control method based on real-time optimization of the integrated aeropropulsion is proposed.Firstly,based on data fitting and physical principle,an integrated onboard model of propulsion system is established,which can calculate various performance parameters of the propulsion system in real time,and has high accuracy and real-time performance.Secondly,to improve the compatibility of optimization real-time performance and search accuracy,the online optimization control of aero-propulsion system is realized based on an improved trust region algorithm.Finally,by controlling the auxiliary intake valve,a good match between inlet and engine is realized,which solves the problems of intake flow reducing and total pressure recovery coefficient declining,and improves the installation performance of propulsion system.The simulation results indicate that,compared with the conventional independent engine control,the real-time integrated optimization method reduces the installed thrust loss by 3.61%under the design condition,and 4.58%under the off-design condition.Furthermore,the simulation on HIL(Hardware-In-theLoop)platform verifies the real-time performance of integrated optimization method.
文摘The high-frequency instability on a cone at 6°angle of attack is measured in a hypersonic quiet wind tunnel with Reynolds number of 6.90×10^(6)m^(−1),and Mach number is 6.Fast-response pressure sensors are used to measure the disturbance waves on the surface of the cone.The nano-tracer-based planar laser scattering(NPLS)technique is used to visualize the coherent structures of the three-dimensional boundary layer.At the plane of azimuthal angle ofθ=30°from the leeward ray,low-and high-frequency disturbance waves with the characteristic frequency of f=10–20 kHz and f=120–140 kHz are detected.From the NPLS image,the regular large-scale traveling crossflow waves structures are observed,which are related to the low-frequency instability.On the top of the traveling crossflow waves,there are a series of small-scale structures,which suggests there is strong shear on the top of the traveling crossflow waves.These small vortices likely are the secondary instability of the traveling crossflow waves,which are associated with the high-frequency instability.The disturbance waves characteristics in different planes are measured using PCB transducers.The result shows that the high-frequency instability occurs in the planes ofθ=15°-60°,and the characteristic frequency is between f=106.97-181.08 kHz.With the increase of azimuthal angle,the characteristic frequency increases obviously,which is related to the thinner boundary layer near the windward side.With the increase of the x-coordinate,the circumferential range of the high-frequency instability gradually widens.
文摘Angle of attack and lateral force are two important parameters influencing wheel rail wear. This paper deals with the question of influences of the angle of attack and the lateral force on the wear of rail. A series of experiments are conducted on 1/4 JD 1 Wheel/Rail Tribology Simulation Facility. The angles of attack selected in the tests are 0°16′30″, 0°37′40″ and 1°0′0″ respectively. The lateral forces selected in the tests are 0.694 kN, 1.250 kN and 2.083 kN, respectively corresponding to the lateral forces of 25 kN, 45 kN and 75 kN measured in the field, with the aim of keeping the same ratio of L/V between laboratory and field conditions. It is found that the larger the angle of attack is, the more serious the wear of rail is. The relation of rail wear rate versus angle of attack is non linear, and the relation of rail wear rate versus lateral force is approximately linear. The influence of angle of attack is more serious than that of lateral force. For the tractive wheelset, the wear index involving linear and quadratic function terms of angle of attack has good agreement with the limited experimental data. Some conclusions are given.
基金supported by the National Natural Science Foundation of China(Nos.12172315,12072304,11702232)the Fujian Provincial Natural Science Foundation,China(No.2021J01050)the Aeronautical Science Foundation of China(No.20220013068002).
文摘Unsteady aerodynamic characteristics at high angles of attack are of great importance to the design and development of advanced fighter aircraft, which are characterized by post-stall maneuverability with multiple Degrees-of-Freedom(multi-DOF) and complex flow field structure.In this paper, a special kind of cable-driven parallel mechanism is firstly utilized as a new suspension method to conduct unsteady dynamic wind tunnel tests at high angles of attack, thereby providing experimental aerodynamic data. These tests include a wide range of multi-DOF coupled oscillatory motions with various amplitudes and frequencies. Then, for aerodynamic modeling and analysis, a novel data-driven Feature-Level Attention Recurrent neural network(FLAR) is proposed. This model incorporates a specially designed feature-level attention module that focuses on the state variables affecting the aerodynamic coefficients, thereby enhancing the physical interpretability of the aerodynamic model. Subsequently, spin maneuver simulations, using a mathematical model as the baseline, are conducted to validate the effectiveness of the FLAR. Finally, the results on wind tunnel data reveal that the FLAR accurately predicts aerodynamic coefficients, and observations through the visualization of attention scores identify the key state variables that affect the aerodynamic coefficients. It is concluded that the proposed FLAR enhances the interpretability of the aerodynamic model while achieving good prediction accuracy and generalization capability for multi-DOF coupling motion at high angles of attack.
基金supported in part by the National Natural Science Foundation of China (No. 12202363)。
文摘Modeling of unsteady aerodynamic loads at high angles of attack using a small amount of experimental or simulation data to construct predictive models for unknown states can greatly improve the efficiency of aircraft unsteady aerodynamic design and flight dynamics analysis.In this paper,aiming at the problems of poor generalization of traditional aerodynamic models and intelligent models,an intelligent aerodynamic modeling method based on gated neural units is proposed.The time memory characteristics of the gated neural unit is fully utilized,thus the nonlinear flow field characterization ability of the learning and training process is enhanced,and the generalization ability of the whole prediction model is improved.The prediction and verification of the model are carried out under the maneuvering flight condition of NACA0015 airfoil.The results show that the model has good adaptability.In the interpolation prediction,the maximum prediction error of the lift and drag coefficients and the moment coefficient does not exceed 10%,which can basically represent the variation characteristics of the entire flow field.In the construction of extrapolation models,the training model based on the strong nonlinear data has good accuracy for weak nonlinear prediction.Furthermore,the error is larger,even exceeding 20%,which indicates that the extrapolation and generalization capabilities need to be further optimized by integrating physical models.Compared with the conventional state space equation model,the proposed method can improve the extrapolation accuracy and efficiency by 78%and 60%,respectively,which demonstrates the applied potential of this method in aerodynamic modeling.
文摘Abstract Accurate aerodynamic models are the basis of flight simulation and control law design. Mathematically modeling unsteady aerodynamics at high angles of attack bears great difficulties in model structure determination and parameter estimation due to little understanding of the flow mechanism. Support vector machines （SVMs） based on statistical learning theory provide a novel tool for nonlinear system modeling. The work presented here examines the feasibility of applying SVMs to high angle.-of-attack unsteady aerodynamic modeling field. Mainly, after a review of SVMs, several issues associated with unsteady aerodynamic modeling by use of SVMs are discussed in detail, such as sele, ction of input variables, selection of output variables and determination of SVM parameters. The least squares SVM （LS-SVM） models are set up from certain dynamic wind tunnel test data of a delta wing and an aircraft configuration, and then used to predict the aerodynamic responses in other tests. The predictions are in good agreement with the test data, which indicates the satisfving learning and generalization performance of LS-SVMs.
基金supported by the Science Foundation of the National University of Defense Technology (Grant No. JC11-01-02)National Natural Science Foundation of China (Grant Nos. 90816027, 61004094)
文摘The high angle of attack characteristics play an important role in the aerodynamic performances of the hypersonic space vehicle. The three-dimensional Reynolds Averaged Navier-Stokes (RANS) equations and the two-equation RNG k-? turbulence model have been employed to investigate the influence of the high angle of attack on the lift-to-drag ratio and the flow field characteristics of the hypersonic space vehicle, and the contributions of each component to the aerodynamic forces of the vehicle have been discussed as well. At the same time, in order to validate the numerical method, the predicted results have been compared with the available experimental data of a hypersonic slender vehicle, and the grid independency has been analyzed. The obtained results show that the predicted lift-to-drag ratio and pitching moment coefficient show very good agreement with the experimental data in the open literature, and the grid system makes only a slight difference to the numerical results. There exists an optimal angle of attack for the aerodynamic performance of the hypersonic space vehicle, and its value is 20°. When the angle of attack is 20°, the high pressure does not leak from around the leading edge to the upper surface. With the further increasing of the angle of attack, the high pressure spreads from the wing tips to the central area of the vehicle, and overflows from the leading edge again. Further, the head plays an important role in the drag performance of the vehicle, and the lift percentage of the flaperon is larger than that of the rudderevator. This illustrates that the optimization of the flaperon configuration is a great work for the improvement of the aerodynamic performance of the hypersonic space vehicle, especially for a high lift-to-drag ratio.
基金National Natural Science Foundation of China(No.:12002261)National Postdoctoral Program for Innovative Talents of China(No.:BX20200267)+2 种基金Young Talent fund of University Association for Science and Technology in Shaanxi of China(No.:20200501)China Postdoctoral Science Foundation(No.:2020M673411)the Fundamental Research Funds for the Central Universities of China(No.:xzy012020096).G.Chen are grateful for the support of National Natural Science Foundation of China(No.:11872293).
文摘A wavecatcher type scramjet intake,that reduces the Mach number number from 4 to 1.552,is used as the basis for a study of flow starting/unstarting as affected by freestream angles of attack and sideslip.The intake design is based on a morphed streamtube consisting of two conical flow streamlines using streamline tracing and osculating axisymmetric design theory.Intake flow and performance is modeled using the numerical CFD code and the k-e turbulence model.The intake unstarts at a sideslip angle of 2,a positive angle of attack of 1.Both positive angle of attack and sideslip angle have an adverse effect on the startability of the MBus intake.At negative angles,the intake initially unstarts at5angle of attack,due to the thickened shear layer induced by the streamwise vortex.Then it re-starts at8angle of attack,mainly due to the expansion fan formed at the leading edge,causing the shock wave structures inside the intake to be reestablished.
文摘The modern high performance air vehicles are required to have extreme maneuverability,which includes the ability of controlled maneuvers at high angle of attack. However, the nonlinear and unsteady aerodynamic phenomena, such as flow separation, vortices interaction, and vortices breaking down, will occur during the flight at high angle of attack, which could induce the uncommanded motions for the air vehicles. For the high maneuverable and agile air missile, the nonlinear roll motions would occur at the high angle of attack. The present work is focused on the selfinduced nonlinear roll motion for a missile configuration and discusses the influence of the strake wings on the roll motion according to the results from free-to-roll test and PIV measurement using the models assembled with different strake wings at a = 60°. The free-to-roll results show that the model with whole strake wings(baseline), the model assembled with three strake wings(Case A)and the model assembled with two opposite strake wings(Case C) experience the spinning, while the model assembled with two adjacent strake wings(Case B), the model assembled with one strake wing(Case D) and the model with no strake wing(Case E) trim or slightly vibrate at a certain "×"rolling angle, which mean that the rolling stability can be improved by dismantling certain strake wings. The flow field results from PIV measurement show that the leeward asymmetric vortices are induced by the windward strake wings. The vortices would interact the strake wings and induce crossflow on the downstream fins to degrade the rolling stability of the model. This could be the main reason for the self-induced roll motion of the model at a = 60°.
