The wetting behavior of slag–coke is a crucial factor influencing the permeability of the lower part of the blast furnace.However,a systematic understanding of the wetting behavior and underlying mechanisms between t...The wetting behavior of slag–coke is a crucial factor influencing the permeability of the lower part of the blast furnace.However,a systematic understanding of the wetting behavior and underlying mechanisms between titanium-containing slag and tuyere coke remains lacking.The sessile drop method was employed to explore the effects of temperature,binary basicity,FeO,and TiO_(2) contents on the wetting behavior of titanium-containing slag and tuyere coke.The results indicate that increasing the temperature enhances the adhesion and wettability of the droplet,reducing the contact angle.Meanwhile,it accelerates the chemical reactions between slag and coke,leading to faster equilibrium.Conversely,increasing slag basicity elevates the contact angle by inhibiting chemical reactions at the slag–coke interface.This inhibition reduces both contact area and depth,thereby hindering slag droplet spreading on the coke surface.The contact angle decreases as the FeO content in the slag increases.Notably,the increase in TiO_(2) content has a dual effect on slag–coke wettability.Initially,it promotes wetting by reducing surface tension and lowering the contact angle.While the TiO_(2) content exceeds 20 wt.%,Ti(C,N)forms a barrier layer at the slag–coke interface,hindering the contact between slag and coke and resulting in an increased contact angle.展开更多
Correction to:Nano-Micro Letters(2026)18:10.https://doi.org/10.1007/s40820-025-01852-8 Following publication of the original article[1],the authors reported that the last author’s name was inadvertently misspelled.Th...Correction to:Nano-Micro Letters(2026)18:10.https://doi.org/10.1007/s40820-025-01852-8 Following publication of the original article[1],the authors reported that the last author’s name was inadvertently misspelled.The published version showed“Hongzhen Chen”,whereas the correct spelling should be“Hongzheng Chen”.The correct author name has been provided in this Correction,and the original article[1]has been corrected.展开更多
This study utilizes wet/dry cyclic corrosion testing combined with corrosion big data technology to investigate the mechanism by which chloride ions(Cl^(-))influence the corrosion behavior of 650 MPa high-strength low...This study utilizes wet/dry cyclic corrosion testing combined with corrosion big data technology to investigate the mechanism by which chloride ions(Cl^(-))influence the corrosion behavior of 650 MPa high-strength low-alloy(HSLA)steel in industrially polluted environments.The corrosion process of 650 MPa HSLA steel occurred in two distinct stages:an initial corrosion stage and a stable corrosion stage.During the initial phase,the weight loss rate increased rapidly owing to the instability of the rust layer.Notably,this study demonstrated that 650 MPa HSLA steel exhibited superior corrosion resistance in Cl-containing environments.The formation of a corrosion-product film eventually reduced the weight-loss rate.However,the intrusion of Cl^(-)at increasing concentrations gradually destabilized theα/γ^(*)phases of the rust layer,leading to a looser structure and lower polarization resistance(R_(p)).The application of corrosion big data technology in this study facilitated the validation and analysis of the experimental results,offering new insights into the corrosion mechanisms of HSLA steel in chloride-rich environments.展开更多
BACKGROUND Despite societal guidelines recommending targeted screening for Barrett’s esophagus(BE)and esophageal adenocarcinoma(EAC)in individuals with gastroesophageal reflux symptoms(GERS),screening adherence is su...BACKGROUND Despite societal guidelines recommending targeted screening for Barrett’s esophagus(BE)and esophageal adenocarcinoma(EAC)in individuals with gastroesophageal reflux symptoms(GERS),screening adherence is suboptimal.Current screening approaches fail to identify individuals not seeking medical consultation for GERS or whose GERS are managed with‘over-the-counter’(OTC)acid suppressant therapies.AIM To assess patients’self-management and help-seeking behavior for GERS.METHODS This cross-sectional study collected data from the Dutch general population aged 18-75 years between January and April 2023 using a web-based survey.The survey included questions regarding self-management(e.g.,use of acid suppressant therapy with or without prescription)and help-seeking behavior(e.g.,consulting a primary care provider)for GERS.Simple random sampling was performed to select individuals within the target age group.In total,18156 randomly selected individuals were invited to participate.The study protocol was registered in ClinicalTrials.gov(identifier:NCT05689918).RESULTS Of the 18156 invited individuals,3214 participants(17.7%)completed the survey,of which 1572 participants(48.9%)reported GERS.Of these,904 participants(57.5%)had never consulted a primary care provider for these symptoms,of which 331 participants(36.6%)reported taking OTC acid suppressant therapy in the past six months and 100 participants(11.1%)fulfilled the screening criteria for BE and EAC according to the European Society of Gastrointestinal Endoscopy Guideline.CONCLUSION The population fulfilling the screening criteria for BE and EAC is incompletely identified,suggesting potential underutilization of medical consultation.Raising public awareness of GERS as a risk factor for EAC is needed.展开更多
BACKGROUND Due to the dry and cold climate,the obvious temperature difference between day and night,and the low oxygen content of the air in the plateau area,people are prone to upper respiratory tract diseases,and of...BACKGROUND Due to the dry and cold climate,the obvious temperature difference between day and night,and the low oxygen content of the air in the plateau area,people are prone to upper respiratory tract diseases,and often the condition is prolonged,and the patients are prone to anxiety and uneasiness,which may be related to the harshness of the plateau environment,somatic discomfort due to the lack of oxygen,anxiety about the disease,and other factors.AIM To investigate the effects of cognitive behavioral therapy(CBT)on anxiety,sleep disorders,and hypoxia tolerance in patients with high-altitude respiratory diseases.METHODS A total of 2337 patients with high-altitude-related respiratory diseases treated at our hospital between November 2023 and January 2024 were selected as the study subjects.The subjects’pre-high-altitude residential altitude was approximately 1700 meters.They were divided into two groups.Both groups were given symptomatic treatment,and the control group implemented conventional nursing intervention,while the research group simultaneously conducted CBT intervention;assessed the degree of health knowledge of the two groups,and applied the Hamilton Anxiety Scale and the Pittsburgh Sleep Quality Index to assess the anxiety and sleep quality of the patients before and after the intervention,respectively.It also observed the length and efficiency of sleep,and detected the level of serum hypoxia inducible factor-1α,erythropoietin(EPO)and clinical intervention before and after intervention.EPO levels,and investigated satisfaction with the clinical intervention.RESULTS The rate of excellent health knowledge in the intervention group was 93.64%,which was higher than that in the control group(74.23%;P<0.05).Before the intervention,there was no significant difference in Hamilton Anxiety Scale and Pittsburgh Sleep Quality Index scores between the two groups(P>0.05),and after the intervention,the scores of the study group were significantly lower than those of the control group(P<0.05).There was no significant difference in sleep duration and sleep efficiency between the groups before the intervention(P>0.05),and after the intervention,the scores of the study group were significantly larger than those of the control group(P<0.05).There was no significant difference in serum hypoxia inducible factor-1αand EPO between the two groups before intervention(P>0.05),and both research groups were significantly lower than the control group after intervention(P<0.05).According to the questionnaire survey,the intervention satisfaction of the study group was 95.53%,which was higher than that of the control group(80.14%;P<0.05).CONCLUSION The CBT intervention in the treatment of patients with high-altitude-related respiratory diseases helps improve patients'health knowledge,relieve anxiety,improve sleep quality and hypoxia tolerance,and improve nursing satisfaction.展开更多
BACKGROUND Approximately 30%of patients with head and neck cancer experience adverse effects caused by anxiety and depression.Considering the high prevalence,implementing customized interventions to ease adverse emoti...BACKGROUND Approximately 30%of patients with head and neck cancer experience adverse effects caused by anxiety and depression.Considering the high prevalence,implementing customized interventions to ease adverse emotional states is imperative.AIM To evaluate the efficacy of cognitive behavioral therapy(CBT)-based psychological interventions in improving the psychological well-being and quality of life(QoL)of patients with laryngeal carcinoma.METHODS This study enrolled 120 patients admitted from February 2022 to February 2024.The control group,comprising 50 participants,received standard supportive psychological care,while the research group,consisting 70 participants,underwent CBT-based interventions.Several clinical outcomes were systematically assessed that included postoperative recovery metrics(duration of tracheostomy and nasogastric tube dependence and length of hospitalization),psychological status(Self-Rating Anxiety Scale and Self-Rating Depression Scale),nutritional markers(serum albumin and hemoglobin levels),sleep quality(Self-Rating Scale of Sleep and Athens Insomnia Scale),and QoL(Functional Assessment of Cancer Therapy-Head and Neck).RESULTS The results demonstrated that the research group experienced superior outcomes,with significantly reduced durations of tracheostomy and nasogastric tube dependence,as well as shorter hospital stays,compared with the control group.Additionally,the research group exhibited markedly lower post-intervention Self-Rating Anxiety Scale,Self-Rating Depression Scale,Self-Rating Scale of Sleep,and Athens Insomnia Scale scores,along with minimal but higher change in serum albumin and hemoglobin levels compared with the control group.All five domains of Functional Assessment of Cancer Therapy-Head and Neck showed notable improvements in the research group,exceeding those observed in the control group.CONCLUSION CBT-based psychological support positively affects the mental well-being and QoL of patients with laryngeal carcinoma,highlighting its potential for broader clinical application.展开更多
Healthy behavior has long been linked to mental health outcomes.However,the role of artificial intelligence(AI)literacy in shaping healthy behaviors and its potential impact on mental health remains underexplored.This...Healthy behavior has long been linked to mental health outcomes.However,the role of artificial intelligence(AI)literacy in shaping healthy behaviors and its potential impact on mental health remains underexplored.This paper presents a scoping review offering a novel perspective on the intersection of healthy behaviors,mental health,and AI literacy.By examining how individuals’understanding of AI influences their choices regarding nutrition and their susceptibility to mental health issues,the current study explores emerging trends in health behavior decision-making.This emphasizes the need for integrating AI literacy into mental health and health behaviors education,as well as the development of AI-driven tools to support healthier behavior choices.It highlights that individuals with low AI literacy may misinterpret or overly depend on AI guidance,resulting in maladaptive health choices,while those with high AI literacy may be more likely to engage reflectively and sustain positive behaviors.The paper outlines the importance of inclusive education,user-centered design,and community-based support systems to enhance AI literacy for digitally marginalized groups.AI literacy may be positioned as a key determinant of health equity,better allowing for interdisciplinary strategies that empower individuals to make informed,autonomous decisions that promote both physical and mental health.展开更多
This paper prepared a novel as-cast W-Zr-Ti metallic ESM using high-frequency vacuum induction melting technique.The above ESM performs a typical elastic-brittle material feature and strain rate strengthening behavior...This paper prepared a novel as-cast W-Zr-Ti metallic ESM using high-frequency vacuum induction melting technique.The above ESM performs a typical elastic-brittle material feature and strain rate strengthening behavior.The specimens exhibit violent chemical reaction during the fracture process under the impact loading,and the size distribution of their residual debris follows Rosin-Rammler model.The dynamic fracture toughness is obtained by the fitting of debris length scale,approximately 1.87 MPa·m~(1/2).Microstructure observation on residual debris indicates that the failure process is determined by primary crack propagation under quasi-static compression,while it is affected by multiple cracks propagation in both particle and matrix in the case of dynamic impact.Impact test demonstrates that the novel energetic fragment performs brilliant penetration and combustion effect behind the front target,leading to the effective ignition of fuel tank.For the brittleness of as-cast W-ZrTi ESM,further study conducted bond-based peridynamic(BB-PD)C++computational code to simulate its fracture behavior during penetration.The BB-PD method successfully captured the fracture process and debris cloud formation of the energetic fragment.This paper explores a novel as-cast metallic ESM,and provides an available numerical avenue to the simulation of brittle energetic fragment.展开更多
The dissimilar 2B06 and 7B04 Al alloy joints were prepared by refill friction stir spot welding(RFSSW),and the microstructural evolution and corrosion behavior of the joints were investigated.Based on microstructural ...The dissimilar 2B06 and 7B04 Al alloy joints were prepared by refill friction stir spot welding(RFSSW),and the microstructural evolution and corrosion behavior of the joints were investigated.Based on microstructural analysis,the welded joints exhibit distinct microstructural zones,including the stir zone(SZ),thermomechanically affected zone(TMAZ),and heat-affected zone(HAZ).The grain size of each zone is in the order of HAZ>TMAZ>SZ.Notably,the TMAZ and HAZ contain significantly larger secondary-phase particles compared to the SZ,with particle size in the HAZ increasing at higher rotational speeds.Electrochemical tests indicate that corrosion susceptibility follows the sequence of HAZ>TMAZ>SZ>BM,with greater sensitivity observed at increased rotational speeds.Post-corrosion mechanical performance degradation primarily arises from crevice corrosion at joint overlaps,but not from the changes in the microstructure.展开更多
In the competitive retail industry of the digital era,data-driven insights into gender-specific customer behavior are essential.They support the optimization of store performance,layout design,product placement,and ta...In the competitive retail industry of the digital era,data-driven insights into gender-specific customer behavior are essential.They support the optimization of store performance,layout design,product placement,and targeted marketing.However,existing computer vision solutions often rely on facial recognition to gather such insights,raising significant privacy and ethical concerns.To address these issues,this paper presents a privacypreserving customer analytics system through two key strategies.First,we deploy a deep learning framework using YOLOv9s,trained on the RCA-TVGender dataset.Cameras are positioned perpendicular to observation areas to reduce facial visibility while maintaining accurate gender classification.Second,we apply AES-128 encryption to customer position data,ensuring secure access and regulatory compliance.Our system achieved overall performance,with 81.5%mAP@50,77.7%precision,and 75.7%recall.Moreover,a 90-min observational study confirmed the system’s ability to generate privacy-protected heatmaps revealing distinct behavioral patterns between male and female customers.For instance,women spent more time in certain areas and showed interest in different products.These results confirm the system’s effectiveness in enabling personalized layout and marketing strategies without compromising privacy.展开更多
The functional properties of glasses are governed by their formation history and the complex relaxation processes they undergo.However,under extreme conditions,glass behaviors are still elusive.In this study,we employ...The functional properties of glasses are governed by their formation history and the complex relaxation processes they undergo.However,under extreme conditions,glass behaviors are still elusive.In this study,we employ simulations with varied protocols to evaluate the effectiveness of different descriptors in predicting mechanical properties across both low-and high-pressure regimes.Our findings demonstrate that conventional structural and configurational descriptors fail to correlate with the mechanical response following pressure release,whereas the activation energy descriptor exhibits robust linearity with shear modulus after correcting for pressure effects.Notably,the soft mode parameter emerges as an ideal and computationally efficient alternative for capturing this mechanical behavior.These findings provide critical insights into the influence of pressure on glassy properties,integrating the distinct features of compressed glasses into a unified theoretical framework.展开更多
Influences of temperature and Sn-Cu droplet's composition on reactive wettings of Cu(100), Cu(110), and Cu(111) surfaces were analyzed, by using molecular dynamics(MD) calculations. As a result, the spreading on C...Influences of temperature and Sn-Cu droplet's composition on reactive wettings of Cu(100), Cu(110), and Cu(111) surfaces were analyzed, by using molecular dynamics(MD) calculations. As a result, the spreading on Cu(110)(Cu(100)) has the fastest(slowest) wetting kinetics. A higher temperature or a diluter Cu content in the Sn-Cu alloy droplet results in a higher wettability. Moreover, this work has addressed a theory for positioning the interface separating the liquidus and solidus alloys in the spreading film to confirm the hypothesis that the reactive wetting will come to the end when the interface saturates with the temperature-dependent solidus weight fraction of Cu.展开更多
We measured the contact angles of Al and Sn drops on polycrystalline Al2O3 substrates in various high magnetic fields at different temperatures.The contact angles of both Al and Sn drops on the Al2O3 substrates decrea...We measured the contact angles of Al and Sn drops on polycrystalline Al2O3 substrates in various high magnetic fields at different temperatures.The contact angles of both Al and Sn drops on the Al2O3 substrates decreased under high magnetic fields.These decreases strongly depend on the temperature,magnetic flux density,magnetic properties of the metal drops,and the reactivity of the metal drops with Al2O3.Our results reveal that the wetting behavior of molten metal drops on ceramics can be modified by a high magnetic field.展开更多
Water molecules could form a liquid droplet on the water monolayer on a specific solid surface, which has been referred to as ‘‘ordered water monolayer that does not completely wet water'' at room temperatur...Water molecules could form a liquid droplet on the water monolayer on a specific solid surface, which has been referred to as ‘‘ordered water monolayer that does not completely wet water'' at room temperature. In contrast to the water molecules, the family of alcohol molecules has the same OH polar head and various lengths of their hydrophobic nonpolar tail; the length of the hydrophobic tail can affect the hydrophobic effect. In this study, using molecular dynamics simulations, we investigated the wetting behaviors of methanol, ethanol, and propanol molecules adsorbed on a SiO_2 surface. The results showed that the methanol, ethanol, and propanol molecules could form an ordered monolayer on the SiO_2 surface and a droplet on top of this monolayer, with different contact angles. The differences in the contact angles were attributed to the differences in the interactions between the alcohol monolayer and droplet.展开更多
Sn-10Sb-5Cu lead-free solder was fabricated for high temperature application in electronic package. Wetting behaviors and interfacial reaction between such a high temperature lead-free solder and Cu substrate were inv...Sn-10Sb-5Cu lead-free solder was fabricated for high temperature application in electronic package. Wetting behaviors and interfacial reaction between such a high temperature lead-free solder and Cu substrate were investigated and compared with those of 95Pb-Sn solder. The results showed that the wetting properties of Sn-10Sb-SCu solder are superior to those of 95Pb-Sn solder in maximum wetting force, wetting time and wetting angle in the temperature range of 340-400℃. However, the surface of the Sn-10Sb-5Cu solder sample after wetting balance tests was rougher than that of 95Pb-Sn solder at the temperature lower than 360℃. In static liquid-state interracial reaction, the types and thickness of the intermetallic compounds （IMCs） of both solders were different from each other. The wetting kinetics in the Sn-10Sb-5Cu/Cu system was more rapid than that in 95Pb-Sn/Cu system, and the higher formation rate of IMCs in the former system was considered as the reason.展开更多
The wettability of molten Al_(x)CoCrCuFeNi(x is from 0 to 1.5,mol.%)high-entropy alloys(HEA)on a WC substrate was measured using a modified sessile drop method at 1823 K in an argon atmosphere.The wetting behaviors an...The wettability of molten Al_(x)CoCrCuFeNi(x is from 0 to 1.5,mol.%)high-entropy alloys(HEA)on a WC substrate was measured using a modified sessile drop method at 1823 K in an argon atmosphere.The wetting behaviors and interfacial characteristics between HEAs and WC were studied.Good wettability with final equilibrium contact angles of 0.5°-4.6°is obtained,and addition of Al deteriorates the wettability of the HEAs.The wetting of Al_(x)CoCrCuFeNi/WC system can be roughly divided into an initially sharp spreading stage and a subsequent steady-state phase.In the first stage,the adsorption of Cr atoms at the solid-liquid interface primarily contributes to the wetting,and the contact angle drastically reduces.However,both the wetting behavior and interfacial microstructure are determined by the Al content of the HEA in the next stage.For x≤0.5,the wetting is mainly driven by the dissolution of WC,although a few reaction products of(W,Cr)_(2)C are observed.Moreover,an obvious dissolution pit appears at the surface of the substrate.When the Al content of x≥1,the interfacial reaction is dominant in competition with the dissolution of WC,and massive reaction products precipitate at the HEA/WC interface,which leads to the formation of a continuous reaction layer.展开更多
It is well known that the compressibility of crushable granular materials increases with the moisture content,due to the decrease of particle strength in a humid environment.An existing approach to take into account t...It is well known that the compressibility of crushable granular materials increases with the moisture content,due to the decrease of particle strength in a humid environment.An existing approach to take into account the effect of grain breakage in constitutive modeling consists in linking the evolution of the grain size distribution to the plastic work.But how the material humidity can affect this relationship is not clear,and experimental evidence is quite scarce.Based on compression tests on dry and saturated crushable sand recently reported by the present authors,a new non-linear relationship is proposed between the amount of particle breakage and the plastic work.The expression contains two parameters:(1)a material constant dependent on the grain characteristics and(2)a constant depending on the wetting condition(in this study,dry or saturated).A key finding is that the relationship does not depend on the stress path and,for a given wetting condition,only one set of parameters is necessary to reproduce the results of isotropic,oedometric,and triaxial compression tests.The relationship has been introduced into an elastoplastic constitutive model based on the critical state concept with a double yield surface for plastic sliding and compression.The breakage ratio is introduced into the expression of the elastic stiffness,the critical state line and the hardening compression pressure.Incremental stress-strain computations with the model allow the plastic work to be calculated and,therefore,the evolution of particle crushing can be predicted through the proposed non-linear relationship and reintroduced into the constitutive equations.Accurate predictions of the experimental results in terms of both stress-strain relationships and breakage ratio were obtained.展开更多
The spontaaleous infiltration aald wetting behaviors of a Zr-based alloy melt on porous a SiC ceramic plate were studied using tile sessile drop metilod by continuous heating and holding for 1800 s at different temper...The spontaaleous infiltration aald wetting behaviors of a Zr-based alloy melt on porous a SiC ceramic plate were studied using tile sessile drop metilod by continuous heating and holding for 1800 s at different temperatures in a high-vacuum furnace. The results showed that tile Zr-based alloy melt could pastly infiltrate tile porous SiC substrate without pressure due to tile effect of capillary pressure. Wettability and infiltration rates increased witil increasing temperature, and interracial reaction products （ZrC0.7 and TiC） were detected in tile Zr-based alloy/SiC ceramic system, likely because of tile reaction of tile active elements Zr and Ti witil elemental C. Furtilelinore, tile redundant ele- ment Si diffused into tile alloy melt.展开更多
The wide engineered application of compacted expansive soils necessitates understanding their behavior under field conditions.The results of this study demonstrate how seasonal climatic variation and stress and bounda...The wide engineered application of compacted expansive soils necessitates understanding their behavior under field conditions.The results of this study demonstrate how seasonal climatic variation and stress and boundary conditions individually or collectively influence the hydraulic and volume change behavior of compacted highly expansive soils.The cyclic wetting and drying(CWD)process was applied for two boundary conditions,i.e.constant stress(CS)and constant volume(CV),and for a wide range of axial stress states.The adopted CWD process affected the hydraulic and volume change behaviors of expansive soils,with the first cycle of wetting and drying being the most effective.The CWD process under CS conditions resulted in shrinkage accumulation and reduction in saturated hydraulic conductivity(k sat).On the other hand,CWD under CV conditions caused a reduction of swell pressure while has almost no impact on k sat.An elastic response to CWD was achieved after the third cycle for saturated hydraulic conductivity(k sat),the third to fourth cycle for the volume change potential under the CV conditions,and the fourth to fifth cycle for the volume change potential under the CS conditions.Finally,both swell pressure(s s)and saturated hydraulic conductivity(k sat)are not fundamental parameters of the expansive soil but rather depend on stress,boundary and wetting conditions.展开更多
基金supported by the Postdoctor Project of Hubei Province(2024HBBHCXA074)National Natural Science Foundation of China(51974212)+2 种基金China Baowu Low Carbon Metallurgy Innovation Foundation(BWLCF202116)Foundation of Hubei Provincial Key Laboratory for New Processes of Ironmaking and Steelmaking(NPISlab25-03)Science and Technology Major Project of Wuhan(2023020302020572).
文摘The wetting behavior of slag–coke is a crucial factor influencing the permeability of the lower part of the blast furnace.However,a systematic understanding of the wetting behavior and underlying mechanisms between titanium-containing slag and tuyere coke remains lacking.The sessile drop method was employed to explore the effects of temperature,binary basicity,FeO,and TiO_(2) contents on the wetting behavior of titanium-containing slag and tuyere coke.The results indicate that increasing the temperature enhances the adhesion and wettability of the droplet,reducing the contact angle.Meanwhile,it accelerates the chemical reactions between slag and coke,leading to faster equilibrium.Conversely,increasing slag basicity elevates the contact angle by inhibiting chemical reactions at the slag–coke interface.This inhibition reduces both contact area and depth,thereby hindering slag droplet spreading on the coke surface.The contact angle decreases as the FeO content in the slag increases.Notably,the increase in TiO_(2) content has a dual effect on slag–coke wettability.Initially,it promotes wetting by reducing surface tension and lowering the contact angle.While the TiO_(2) content exceeds 20 wt.%,Ti(C,N)forms a barrier layer at the slag–coke interface,hindering the contact between slag and coke and resulting in an increased contact angle.
文摘Correction to:Nano-Micro Letters(2026)18:10.https://doi.org/10.1007/s40820-025-01852-8 Following publication of the original article[1],the authors reported that the last author’s name was inadvertently misspelled.The published version showed“Hongzhen Chen”,whereas the correct spelling should be“Hongzheng Chen”.The correct author name has been provided in this Correction,and the original article[1]has been corrected.
基金financially supported by the National Natural Science Foundation of China(Nos.52104319 and 52374323)。
文摘This study utilizes wet/dry cyclic corrosion testing combined with corrosion big data technology to investigate the mechanism by which chloride ions(Cl^(-))influence the corrosion behavior of 650 MPa high-strength low-alloy(HSLA)steel in industrially polluted environments.The corrosion process of 650 MPa HSLA steel occurred in two distinct stages:an initial corrosion stage and a stable corrosion stage.During the initial phase,the weight loss rate increased rapidly owing to the instability of the rust layer.Notably,this study demonstrated that 650 MPa HSLA steel exhibited superior corrosion resistance in Cl-containing environments.The formation of a corrosion-product film eventually reduced the weight-loss rate.However,the intrusion of Cl^(-)at increasing concentrations gradually destabilized theα/γ^(*)phases of the rust layer,leading to a looser structure and lower polarization resistance(R_(p)).The application of corrosion big data technology in this study facilitated the validation and analysis of the experimental results,offering new insights into the corrosion mechanisms of HSLA steel in chloride-rich environments.
文摘BACKGROUND Despite societal guidelines recommending targeted screening for Barrett’s esophagus(BE)and esophageal adenocarcinoma(EAC)in individuals with gastroesophageal reflux symptoms(GERS),screening adherence is suboptimal.Current screening approaches fail to identify individuals not seeking medical consultation for GERS or whose GERS are managed with‘over-the-counter’(OTC)acid suppressant therapies.AIM To assess patients’self-management and help-seeking behavior for GERS.METHODS This cross-sectional study collected data from the Dutch general population aged 18-75 years between January and April 2023 using a web-based survey.The survey included questions regarding self-management(e.g.,use of acid suppressant therapy with or without prescription)and help-seeking behavior(e.g.,consulting a primary care provider)for GERS.Simple random sampling was performed to select individuals within the target age group.In total,18156 randomly selected individuals were invited to participate.The study protocol was registered in ClinicalTrials.gov(identifier:NCT05689918).RESULTS Of the 18156 invited individuals,3214 participants(17.7%)completed the survey,of which 1572 participants(48.9%)reported GERS.Of these,904 participants(57.5%)had never consulted a primary care provider for these symptoms,of which 331 participants(36.6%)reported taking OTC acid suppressant therapy in the past six months and 100 participants(11.1%)fulfilled the screening criteria for BE and EAC according to the European Society of Gastrointestinal Endoscopy Guideline.CONCLUSION The population fulfilling the screening criteria for BE and EAC is incompletely identified,suggesting potential underutilization of medical consultation.Raising public awareness of GERS as a risk factor for EAC is needed.
基金Supported by Army Logistics Department Health Bureau Project,No.QJGYXYJZX-012.
文摘BACKGROUND Due to the dry and cold climate,the obvious temperature difference between day and night,and the low oxygen content of the air in the plateau area,people are prone to upper respiratory tract diseases,and often the condition is prolonged,and the patients are prone to anxiety and uneasiness,which may be related to the harshness of the plateau environment,somatic discomfort due to the lack of oxygen,anxiety about the disease,and other factors.AIM To investigate the effects of cognitive behavioral therapy(CBT)on anxiety,sleep disorders,and hypoxia tolerance in patients with high-altitude respiratory diseases.METHODS A total of 2337 patients with high-altitude-related respiratory diseases treated at our hospital between November 2023 and January 2024 were selected as the study subjects.The subjects’pre-high-altitude residential altitude was approximately 1700 meters.They were divided into two groups.Both groups were given symptomatic treatment,and the control group implemented conventional nursing intervention,while the research group simultaneously conducted CBT intervention;assessed the degree of health knowledge of the two groups,and applied the Hamilton Anxiety Scale and the Pittsburgh Sleep Quality Index to assess the anxiety and sleep quality of the patients before and after the intervention,respectively.It also observed the length and efficiency of sleep,and detected the level of serum hypoxia inducible factor-1α,erythropoietin(EPO)and clinical intervention before and after intervention.EPO levels,and investigated satisfaction with the clinical intervention.RESULTS The rate of excellent health knowledge in the intervention group was 93.64%,which was higher than that in the control group(74.23%;P<0.05).Before the intervention,there was no significant difference in Hamilton Anxiety Scale and Pittsburgh Sleep Quality Index scores between the two groups(P>0.05),and after the intervention,the scores of the study group were significantly lower than those of the control group(P<0.05).There was no significant difference in sleep duration and sleep efficiency between the groups before the intervention(P>0.05),and after the intervention,the scores of the study group were significantly larger than those of the control group(P<0.05).There was no significant difference in serum hypoxia inducible factor-1αand EPO between the two groups before intervention(P>0.05),and both research groups were significantly lower than the control group after intervention(P<0.05).According to the questionnaire survey,the intervention satisfaction of the study group was 95.53%,which was higher than that of the control group(80.14%;P<0.05).CONCLUSION The CBT intervention in the treatment of patients with high-altitude-related respiratory diseases helps improve patients'health knowledge,relieve anxiety,improve sleep quality and hypoxia tolerance,and improve nursing satisfaction.
文摘BACKGROUND Approximately 30%of patients with head and neck cancer experience adverse effects caused by anxiety and depression.Considering the high prevalence,implementing customized interventions to ease adverse emotional states is imperative.AIM To evaluate the efficacy of cognitive behavioral therapy(CBT)-based psychological interventions in improving the psychological well-being and quality of life(QoL)of patients with laryngeal carcinoma.METHODS This study enrolled 120 patients admitted from February 2022 to February 2024.The control group,comprising 50 participants,received standard supportive psychological care,while the research group,consisting 70 participants,underwent CBT-based interventions.Several clinical outcomes were systematically assessed that included postoperative recovery metrics(duration of tracheostomy and nasogastric tube dependence and length of hospitalization),psychological status(Self-Rating Anxiety Scale and Self-Rating Depression Scale),nutritional markers(serum albumin and hemoglobin levels),sleep quality(Self-Rating Scale of Sleep and Athens Insomnia Scale),and QoL(Functional Assessment of Cancer Therapy-Head and Neck).RESULTS The results demonstrated that the research group experienced superior outcomes,with significantly reduced durations of tracheostomy and nasogastric tube dependence,as well as shorter hospital stays,compared with the control group.Additionally,the research group exhibited markedly lower post-intervention Self-Rating Anxiety Scale,Self-Rating Depression Scale,Self-Rating Scale of Sleep,and Athens Insomnia Scale scores,along with minimal but higher change in serum albumin and hemoglobin levels compared with the control group.All five domains of Functional Assessment of Cancer Therapy-Head and Neck showed notable improvements in the research group,exceeding those observed in the control group.CONCLUSION CBT-based psychological support positively affects the mental well-being and QoL of patients with laryngeal carcinoma,highlighting its potential for broader clinical application.
文摘Healthy behavior has long been linked to mental health outcomes.However,the role of artificial intelligence(AI)literacy in shaping healthy behaviors and its potential impact on mental health remains underexplored.This paper presents a scoping review offering a novel perspective on the intersection of healthy behaviors,mental health,and AI literacy.By examining how individuals’understanding of AI influences their choices regarding nutrition and their susceptibility to mental health issues,the current study explores emerging trends in health behavior decision-making.This emphasizes the need for integrating AI literacy into mental health and health behaviors education,as well as the development of AI-driven tools to support healthier behavior choices.It highlights that individuals with low AI literacy may misinterpret or overly depend on AI guidance,resulting in maladaptive health choices,while those with high AI literacy may be more likely to engage reflectively and sustain positive behaviors.The paper outlines the importance of inclusive education,user-centered design,and community-based support systems to enhance AI literacy for digitally marginalized groups.AI literacy may be positioned as a key determinant of health equity,better allowing for interdisciplinary strategies that empower individuals to make informed,autonomous decisions that promote both physical and mental health.
文摘This paper prepared a novel as-cast W-Zr-Ti metallic ESM using high-frequency vacuum induction melting technique.The above ESM performs a typical elastic-brittle material feature and strain rate strengthening behavior.The specimens exhibit violent chemical reaction during the fracture process under the impact loading,and the size distribution of their residual debris follows Rosin-Rammler model.The dynamic fracture toughness is obtained by the fitting of debris length scale,approximately 1.87 MPa·m~(1/2).Microstructure observation on residual debris indicates that the failure process is determined by primary crack propagation under quasi-static compression,while it is affected by multiple cracks propagation in both particle and matrix in the case of dynamic impact.Impact test demonstrates that the novel energetic fragment performs brilliant penetration and combustion effect behind the front target,leading to the effective ignition of fuel tank.For the brittleness of as-cast W-ZrTi ESM,further study conducted bond-based peridynamic(BB-PD)C++computational code to simulate its fracture behavior during penetration.The BB-PD method successfully captured the fracture process and debris cloud formation of the energetic fragment.This paper explores a novel as-cast metallic ESM,and provides an available numerical avenue to the simulation of brittle energetic fragment.
基金supported by the National Natural Science Foundation of China (Nos. 52075449, 51975480)。
文摘The dissimilar 2B06 and 7B04 Al alloy joints were prepared by refill friction stir spot welding(RFSSW),and the microstructural evolution and corrosion behavior of the joints were investigated.Based on microstructural analysis,the welded joints exhibit distinct microstructural zones,including the stir zone(SZ),thermomechanically affected zone(TMAZ),and heat-affected zone(HAZ).The grain size of each zone is in the order of HAZ>TMAZ>SZ.Notably,the TMAZ and HAZ contain significantly larger secondary-phase particles compared to the SZ,with particle size in the HAZ increasing at higher rotational speeds.Electrochemical tests indicate that corrosion susceptibility follows the sequence of HAZ>TMAZ>SZ>BM,with greater sensitivity observed at increased rotational speeds.Post-corrosion mechanical performance degradation primarily arises from crevice corrosion at joint overlaps,but not from the changes in the microstructure.
文摘In the competitive retail industry of the digital era,data-driven insights into gender-specific customer behavior are essential.They support the optimization of store performance,layout design,product placement,and targeted marketing.However,existing computer vision solutions often rely on facial recognition to gather such insights,raising significant privacy and ethical concerns.To address these issues,this paper presents a privacypreserving customer analytics system through two key strategies.First,we deploy a deep learning framework using YOLOv9s,trained on the RCA-TVGender dataset.Cameras are positioned perpendicular to observation areas to reduce facial visibility while maintaining accurate gender classification.Second,we apply AES-128 encryption to customer position data,ensuring secure access and regulatory compliance.Our system achieved overall performance,with 81.5%mAP@50,77.7%precision,and 75.7%recall.Moreover,a 90-min observational study confirmed the system’s ability to generate privacy-protected heatmaps revealing distinct behavioral patterns between male and female customers.For instance,women spent more time in certain areas and showed interest in different products.These results confirm the system’s effectiveness in enabling personalized layout and marketing strategies without compromising privacy.
基金supported by the National Natural Science Foundation of China (Grant Nos.T2325004 and 52161160330)the National Natural Science Foundation of China (Grants No.12504233)+2 种基金Advanced MaterialsNational Science and Technology Major Project (Grant No.2024ZD0606900)the Talent Hub for “AI+New Materials” Basic Researchthe Key Research and Development Program of Ningbo (Grant No.2025Z088)。
文摘The functional properties of glasses are governed by their formation history and the complex relaxation processes they undergo.However,under extreme conditions,glass behaviors are still elusive.In this study,we employ simulations with varied protocols to evaluate the effectiveness of different descriptors in predicting mechanical properties across both low-and high-pressure regimes.Our findings demonstrate that conventional structural and configurational descriptors fail to correlate with the mechanical response following pressure release,whereas the activation energy descriptor exhibits robust linearity with shear modulus after correcting for pressure effects.Notably,the soft mode parameter emerges as an ideal and computationally efficient alternative for capturing this mechanical behavior.These findings provide critical insights into the influence of pressure on glassy properties,integrating the distinct features of compressed glasses into a unified theoretical framework.
文摘Influences of temperature and Sn-Cu droplet's composition on reactive wettings of Cu(100), Cu(110), and Cu(111) surfaces were analyzed, by using molecular dynamics(MD) calculations. As a result, the spreading on Cu(110)(Cu(100)) has the fastest(slowest) wetting kinetics. A higher temperature or a diluter Cu content in the Sn-Cu alloy droplet results in a higher wettability. Moreover, this work has addressed a theory for positioning the interface separating the liquidus and solidus alloys in the spreading film to confirm the hypothesis that the reactive wetting will come to the end when the interface saturates with the temperature-dependent solidus weight fraction of Cu.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51774086,51574073,51425401,and 51690161)Fundamental Research Funds for the Central Universities(Grant Nos.N180915002,N170902002 and N170908001)Liaoning Innovative Research Team in University,China(Grant No.LT2017011).
文摘We measured the contact angles of Al and Sn drops on polycrystalline Al2O3 substrates in various high magnetic fields at different temperatures.The contact angles of both Al and Sn drops on the Al2O3 substrates decreased under high magnetic fields.These decreases strongly depend on the temperature,magnetic flux density,magnetic properties of the metal drops,and the reactivity of the metal drops with Al2O3.Our results reveal that the wetting behavior of molten metal drops on ceramics can be modified by a high magnetic field.
基金supported by the National Natural Science Foundation of China(Nos.U1532260,11674345,and 11504032)Key Research Program of Chinese Academy of Sciences(Nos.KJZD-EW-M03 and QYZDJ-SSW-SLH019)+3 种基金Youth Innovation Promotion Association CAS(Grant Number 2014233)Shanghai Supercomputer Center of ChinaComputer Network Information Center of Chinese Academy of SciencesSpecial Program for Applied Research on Super Computation of the NSFC-Guangdong Joint Fund
文摘Water molecules could form a liquid droplet on the water monolayer on a specific solid surface, which has been referred to as ‘‘ordered water monolayer that does not completely wet water'' at room temperature. In contrast to the water molecules, the family of alcohol molecules has the same OH polar head and various lengths of their hydrophobic nonpolar tail; the length of the hydrophobic tail can affect the hydrophobic effect. In this study, using molecular dynamics simulations, we investigated the wetting behaviors of methanol, ethanol, and propanol molecules adsorbed on a SiO_2 surface. The results showed that the methanol, ethanol, and propanol molecules could form an ordered monolayer on the SiO_2 surface and a droplet on top of this monolayer, with different contact angles. The differences in the contact angles were attributed to the differences in the interactions between the alcohol monolayer and droplet.
基金supported by the Science and Technology Program of Zhejiang Province,China (No.2008F1024)
文摘Sn-10Sb-5Cu lead-free solder was fabricated for high temperature application in electronic package. Wetting behaviors and interfacial reaction between such a high temperature lead-free solder and Cu substrate were investigated and compared with those of 95Pb-Sn solder. The results showed that the wetting properties of Sn-10Sb-SCu solder are superior to those of 95Pb-Sn solder in maximum wetting force, wetting time and wetting angle in the temperature range of 340-400℃. However, the surface of the Sn-10Sb-5Cu solder sample after wetting balance tests was rougher than that of 95Pb-Sn solder at the temperature lower than 360℃. In static liquid-state interracial reaction, the types and thickness of the intermetallic compounds （IMCs） of both solders were different from each other. The wetting kinetics in the Sn-10Sb-5Cu/Cu system was more rapid than that in 95Pb-Sn/Cu system, and the higher formation rate of IMCs in the former system was considered as the reason.
基金the National Key R&D Program of China(No.2017YFB0305702)the Major Special Project for Industry-university-research Collaborative Innovation of Guangzhou City(No.201604020139)+1 种基金the Project for Science and Technology Program of Guangdong Province(No.2016A020220005)the Major Special Projects for Science and Technology Program of Guangdong Province(Nos.2014B010129002 and 2019B090907001),China。
文摘The wettability of molten Al_(x)CoCrCuFeNi(x is from 0 to 1.5,mol.%)high-entropy alloys(HEA)on a WC substrate was measured using a modified sessile drop method at 1823 K in an argon atmosphere.The wetting behaviors and interfacial characteristics between HEAs and WC were studied.Good wettability with final equilibrium contact angles of 0.5°-4.6°is obtained,and addition of Al deteriorates the wettability of the HEAs.The wetting of Al_(x)CoCrCuFeNi/WC system can be roughly divided into an initially sharp spreading stage and a subsequent steady-state phase.In the first stage,the adsorption of Cr atoms at the solid-liquid interface primarily contributes to the wetting,and the contact angle drastically reduces.However,both the wetting behavior and interfacial microstructure are determined by the Al content of the HEA in the next stage.For x≤0.5,the wetting is mainly driven by the dissolution of WC,although a few reaction products of(W,Cr)_(2)C are observed.Moreover,an obvious dissolution pit appears at the surface of the substrate.When the Al content of x≥1,the interfacial reaction is dominant in competition with the dissolution of WC,and massive reaction products precipitate at the HEA/WC interface,which leads to the formation of a continuous reaction layer.
基金financial support of CONICYT Chile through project FONDECYT 11150084
文摘It is well known that the compressibility of crushable granular materials increases with the moisture content,due to the decrease of particle strength in a humid environment.An existing approach to take into account the effect of grain breakage in constitutive modeling consists in linking the evolution of the grain size distribution to the plastic work.But how the material humidity can affect this relationship is not clear,and experimental evidence is quite scarce.Based on compression tests on dry and saturated crushable sand recently reported by the present authors,a new non-linear relationship is proposed between the amount of particle breakage and the plastic work.The expression contains two parameters:(1)a material constant dependent on the grain characteristics and(2)a constant depending on the wetting condition(in this study,dry or saturated).A key finding is that the relationship does not depend on the stress path and,for a given wetting condition,only one set of parameters is necessary to reproduce the results of isotropic,oedometric,and triaxial compression tests.The relationship has been introduced into an elastoplastic constitutive model based on the critical state concept with a double yield surface for plastic sliding and compression.The breakage ratio is introduced into the expression of the elastic stiffness,the critical state line and the hardening compression pressure.Incremental stress-strain computations with the model allow the plastic work to be calculated and,therefore,the evolution of particle crushing can be predicted through the proposed non-linear relationship and reintroduced into the constitutive equations.Accurate predictions of the experimental results in terms of both stress-strain relationships and breakage ratio were obtained.
基金the financial support from the National Natural Science Foundation of China(No.51401131)the China's Manned Space Station Project(No.TGJZ800–2–RW024)
文摘The spontaaleous infiltration aald wetting behaviors of a Zr-based alloy melt on porous a SiC ceramic plate were studied using tile sessile drop metilod by continuous heating and holding for 1800 s at different temperatures in a high-vacuum furnace. The results showed that tile Zr-based alloy melt could pastly infiltrate tile porous SiC substrate without pressure due to tile effect of capillary pressure. Wettability and infiltration rates increased witil increasing temperature, and interracial reaction products （ZrC0.7 and TiC） were detected in tile Zr-based alloy/SiC ceramic system, likely because of tile reaction of tile active elements Zr and Ti witil elemental C. Furtilelinore, tile redundant ele- ment Si diffused into tile alloy melt.
文摘The wide engineered application of compacted expansive soils necessitates understanding their behavior under field conditions.The results of this study demonstrate how seasonal climatic variation and stress and boundary conditions individually or collectively influence the hydraulic and volume change behavior of compacted highly expansive soils.The cyclic wetting and drying(CWD)process was applied for two boundary conditions,i.e.constant stress(CS)and constant volume(CV),and for a wide range of axial stress states.The adopted CWD process affected the hydraulic and volume change behaviors of expansive soils,with the first cycle of wetting and drying being the most effective.The CWD process under CS conditions resulted in shrinkage accumulation and reduction in saturated hydraulic conductivity(k sat).On the other hand,CWD under CV conditions caused a reduction of swell pressure while has almost no impact on k sat.An elastic response to CWD was achieved after the third cycle for saturated hydraulic conductivity(k sat),the third to fourth cycle for the volume change potential under the CV conditions,and the fourth to fifth cycle for the volume change potential under the CS conditions.Finally,both swell pressure(s s)and saturated hydraulic conductivity(k sat)are not fundamental parameters of the expansive soil but rather depend on stress,boundary and wetting conditions.
