Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electroche...Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electrochemical measurements were used to characterize its morphology,crystal structure,and electrochemical properties.Removal of aniline by the Ti/TiOxHy/Sb-SnO2electrode was investigated by ultraviolet-Visible spectroscopy and chemical oxygen demand（COD）analysis under different conditions,including current densities,initial concentrations of aniline,pH values,concentrations of chloride ions,and types of reactor.It was found that a higher current density,a lower initial concentration of aniline,an acidic solution,the presence of chloride ions（0.2wt%NaCl）,and a three-dimensional（3D） reactor promoted the removal efficiency of aniline.Electrochemical degradation of aniline followed pseudo-first-order kinetics.The aniline（200 mL of 100mg·L-（-1）） and COD removal efficiencies reached 100%and 73.5%,respectively,at a current density of 20 mA·cm-（-2）,pH of 7.0,and supporting electrolyte of 0.5 wt%Na2SO4 after 2 h electrolysis in a 3D reactor.These results show that aniline can be significantly removed on the Ti/TiOxHy/Sb-SnO2electrode,which provides an efficient way for elimination of aniline from aqueous solution.展开更多
Ti/Sb-SnO2 anodes were prepared by thermal decomposition to examine the influence of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol. The p...Ti/Sb-SnO2 anodes were prepared by thermal decomposition to examine the influence of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol. The physicochemical properties of the Sb-SnO2 coating were markedly influenced by different amounts of Sb dopant. The electrodes, which contained 5% Sb dopant in the coating, presented a much more homogenous surface and much smaller mud-cracks, compared with Ti/Sb-SnO2 electrodes containing 10% or 15% Sb dopant, which exibited larger mud cracks and pores on the surface. However, the main microstructure remained unchanged with the addition of the Sb dopant. No new crystal phase was observed by X-ray diffraction （XRD）. The electrochemical oxidation of 4-chlorophenol on the Ti/SnO2 electrode with 5% Sb dopant was inclined to electrochemical combustion; while for those containing more Sb dopant, intermediate species were accumulated. The electrodes with 5% Sb dopant showed the highest efficiency in the bulk electrolysis of 4-chlorophenol at a current density of 20 mA/cm^2 for 180 min; and the removal rates of 4-chlorophenol and COD were 51.0% and 48.9%, respectively.展开更多
Ti3C2Tx,a novel two-dimensional layer material,is widely used as electrode materials of supercapacitor due to its good metal conductivity,redox reaction active surface,and so on.However,there are many challenges to be...Ti3C2Tx,a novel two-dimensional layer material,is widely used as electrode materials of supercapacitor due to its good metal conductivity,redox reaction active surface,and so on.However,there are many challenges to be addressed which impede Ti3C2Tx obtaining the ideal specific capacitance,such as restacking,re-crushing,and oxidation of titanium.Recently,many advances have been proposed to enhance capacitance performance of Ti3C2Tx.In this review,recent strategies for improving specific capacitance are summarized and compared,for example,film formation,surface modification,and composite method.Furthermore,in order to comprehend the mechanism of those efforts,this review analyzes the energy storage performance in different electrolytes and influencing factors.This review is expected to predict redouble research direction of Ti3C2Tx materials in supercapacitors.展开更多
Praseodymium was selected as a promoter for SnO2/Ti electrode to improve the electrocatalytic performance by electrodeposition in pharmaceutical wastewater treatment; the micrograph and the structure were characterize...Praseodymium was selected as a promoter for SnO2/Ti electrode to improve the electrocatalytic performance by electrodeposition in pharmaceutical wastewater treatment; the micrograph and the structure were characterized by SEM and XRD. Mixture uniform design was used in the optimization of the electrolytic conditions; mathematical model was established according to the rate of wiping COD off, which revealed the relationship between the current intensity, time of electrolysis, the amount of doped Pr, and the ratio of area （SnOJTi：Al）. On the basis of the analysis of the empirical model, the optimized parameters had been obtained; the rate of wiping COD off was up to 94.9%, it decreased from 392 to 20 mg/L. Experimental results showed that the electrocatalytic performance of the electrode doped with Pr was superior for the treatment of pharmaceutical wastewater.展开更多
Electrochemicaldegradation of2,4-dichlorophenol （2,4-DCP） in aqueous solutionwas investigated over Ti/SnO2-Sb anode. The factors influencing thedegradation rate, such as applied currentdensity （2-40 mA/cm2 ）, pH ...Electrochemicaldegradation of2,4-dichlorophenol （2,4-DCP） in aqueous solutionwas investigated over Ti/SnO2-Sb anode. The factors influencing thedegradation rate, such as applied currentdensity （2-40 mA/cm2 ）, pH （3-11） and initial concentration （5-200 mg/L）were evaluated. Thedegradation of2,4-DCP followed apparent pseudo first-order kinetics. Thedegradation ratio on Ti/SnO2 -Sb anode attained 〉 99.9% after 20 min of electrolysis at initial 5-200 mg/L concentrations at a constant currentdensity of 30 mA/cm2 with a 10 mmol/L sodium sulphate （Na2SO4 ） supporting electrolyte solution. The results showed that 2,4-DCP （100 mg/L）degradation and total organic carbon （TOC） removal ratio achieved 99.9% and 92.8%, respectively, at the optimal conditions after 30 min electrolysis. Under this condition, thedegradation rate constant （k） and thedegradation half-life （t1/2 ）were 0.21 min1 and （2.8 ± 0.2） min, respectively. Mainly carboxylic acids （propanoic acid, maleic acid, propanedioic acid, acetic acid and oxalic acid） weredetected as intermediates. The energy efficiencies for2,4-DCPdegradation （5-200 mg/L）with Ti/SnO2-Sb anode ranged from 0.672 to 1.602 g/kWh. The Ti/SnO2-Sb anodewith a high activity to rapid organic oxidation could be employed todegrade chlorophenols, particularly2,4-DCP inwastewater.展开更多
The electrochemical behavior of vitamin C（ascorbic acid or AA） is investigated on the surface of a carbon-paste electrode modified with TiO2 nanoparticles and 2,2＇-（1,2 butanediylbis（nitriloethylidyne））-bis-hyd...The electrochemical behavior of vitamin C（ascorbic acid or AA） is investigated on the surface of a carbon-paste electrode modified with TiO2 nanoparticles and 2,2＇-（1,2 butanediylbis（nitriloethylidyne））-bis-hydroquinone（BBNBH）.The prepared modified electrode showed an efficient catalytic role in the electrochemical oxidation of AA,leading to remarkable decrease in oxidation overpotential and enhancement of the kinetics of the electrode reaction.This modified electrode exhibits well-separated oxidation peaks for AA and uric acid（UA）.The modified electrode is successfully applied for the accurate determination of AA in pharmaceutical preparations.展开更多
The ZnO-modified TiO2 electrode was prepared by adding Zn（CH3COO）2·2H2O to the TiO2 colloid during the sol-gel production process, and was used in dye-sensitized solar cells （DSCs）. The open circuit voltage ...The ZnO-modified TiO2 electrode was prepared by adding Zn（CH3COO）2·2H2O to the TiO2 colloid during the sol-gel production process, and was used in dye-sensitized solar cells （DSCs）. The open circuit voltage （Voc） and fill factor （if） of the cells were improved sig- nificantly. The performances of the ZnO-modified TiO2 electrode such as dark current, transient photocurrent, impedance, absorption spectra, and fiat band potential （Vfb） were investigated. It is found that the interface charge recombination impedance increases and Vfb shifts about 200 mV toward the cathodic potential. The effect mechanism of ZnO modification on the performance of DSCs may be that ZnO occupies the surface states of the TiO2 film.展开更多
Regulation of the electronic structure and interface property becomes a major strategy in the preparation of electrocatalyst.This paper reports the synthesis of cerium(Ce)and sodium dodecyl benzene sulfonate(SDBS)como...Regulation of the electronic structure and interface property becomes a major strategy in the preparation of electrocatalyst.This paper reports the synthesis of cerium(Ce)and sodium dodecyl benzene sulfonate(SDBS)comodified Ti/PbO_(2)electrodes(Ti/PbO2CeSDBS).Ce and SDBS could greatly change the electronic structure and interface property of PbO2.Ti/PbO_(2)CeSDBS exhibited excellent electrocatalytic activity and stability in Rhodamine B(RhB)electrocatalytic oxidation reaction.The improved electrocatalytic activity associates with the synergistic effect of electronic and interface factors.In the electrochemical degradation of RhB,the removal efficiencies of RhB and COD are about 0.880 and 0.694 respectively after the electrolysis of 220 min with Ti/PbO_(2)Ce4SDBS40,which are higher than the contrast Ti/PbO_(2)electrodes.In the meantime,the accelerated lifetime of Ti/PbO_(2)Ce4SDBS40 is more than 6.2 times than that of Ti/PbO_(2).展开更多
TiO2 nanotube （TINT） electrodes anodized in fluorinated organic solutions were successfully prepared on Ti sheets. Field-emission scanning electron microscopy （FE-SEM） and X-ray diffraction （XRD） were performed ...TiO2 nanotube （TINT） electrodes anodized in fluorinated organic solutions were successfully prepared on Ti sheets. Field-emission scanning electron microscopy （FE-SEM） and X-ray diffraction （XRD） were performed to characterize the TiNT electrodes. The linear voltammetry results under irradiation showed that the TiNT electrode annealed at 450℃ presented the highest photoelectrochemical activity. By combining photocatalytic with electrochemical process, a significantly synergetic effect on ammonia degradation was observed with Na2SO4 as supporting electrolyte at pH 10.7. Furthermore, the photoelectrocatalytic efficiency on the ammonia degradation was greatly enhanced in presence of chloride ions without the limitation ofpH. The degradation rate was improved by 14.8 times reaching 4.98 × 10^-2 min^-1 at pH 10.7 and a faster degradation rate of 6.34 × 10^-2 min^-1 was obtained at pH 3.01. The in situ photoelectrocatalytic generated active chlorine was proposed to be responsible for the improved efficiency. On the other hand, an enhanced degradation of ammonia using TiNT electrode fabricated in fluorinated organic solution was also confirmed compared to TiNT electrode anodized in fluorinated water solution and TiO2 film electrode fabricated by sol-gel method. Finally, the effect of chloride concentration was also discussed.展开更多
Ti/SnO2–Sb electrode has a good effect on the removal of organic pollutants. But its short service life limits its large-scale application in industry. Electro-catalytic degradation performances and service life of t...Ti/SnO2–Sb electrode has a good effect on the removal of organic pollutants. But its short service life limits its large-scale application in industry. Electro-catalytic degradation performances and service life of the electrode can be significantly improved by doping rare earth（RE） ions into the oxide coating of Ti/SnO2–Sb electrode. Ti/SnO2–Sb electrodes doped with different RE elements（Ce, Dy, La, and Eu） were prepared by the thermal decomposition method at 550 ℃. Electro-catalytic degradation performances of electrodes doped with different RE elements were evaluated by linear sweep voltammetry（LSV） and Tafel curves. During the electrolysis,the conversion of p-nitrophenol was performed with these electrodes as anodes under galvanostatic control. The structures and morphologies of the surface coating of the electrodes were characterized by scanning electron microscope（SEM）. The results demonstrate that the electro-catalytic degradation performances of Ti/SnO2–Sb electrodes are improved to different levels by doping different RE ions. Improved Ti/SnO2–Sb electrodes by the introduction of different RE have higher oxygen evolution potential, better electro-catalysis ability, better coverage,and longer electrode life.展开更多
Pd-MnO2/TiO2 nanotube arrays（NTAs） photo-electrodes were successfully fabricated via anodization and electro deposition subsequently; the obtained Pd-MnO2/TiO2 NTAs photo electrodes were analyzed by scanning electro...Pd-MnO2/TiO2 nanotube arrays（NTAs） photo-electrodes were successfully fabricated via anodization and electro deposition subsequently; the obtained Pd-MnO2/TiO2 NTAs photo electrodes were analyzed by scanning electron microscopy（SEM）, X-ray diffraction（XRD） and characterized accordingly. Moreover, the light harvesting and absorption properties were investigated via ultraviolet–visible diffuse reflectance spectrum（DRS）; photo degradation efficiency was investigated via analyzing the photo catalytic degradation of Rhodamine B under visible illumination（xenon light）. The performed analyses illustrated that Pd-MnO2 codoped particles were successfully deposited onto the surface of the TiO2 nanotube arrays;DRS results showed significant improvement in visible light absorption which was between400 and 700 nm. Finally, the photo catalytic degradation efficiency results of the designated organic pollutant（Rhodamine B） illustrated a superior photocatalytic（PC） efficiency of approximately 95% compared to the bare TiO2 NTAs, which only exhibited a photo catalytic degradation efficiency of approximately 61%, thus it indicated the significant enhancement of the light absorption properties of fabricated photo electrodes and their yield of UOH radicals.展开更多
Tetrasulfonated Zn,Co,Ga,In,TiO and metal free phthalocyanine (MTsPc) mainly exist as dimers on the nanostructured TiO 2 electrode and mostly exist as monomers in dimethyl sulfoxide. The photocurrent action spectra ...Tetrasulfonated Zn,Co,Ga,In,TiO and metal free phthalocyanine (MTsPc) mainly exist as dimers on the nanostructured TiO 2 electrode and mostly exist as monomers in dimethyl sulfoxide. The photocurrent action spectra of the liquid junction based on the MTsPc/TiO 2 nanostructured electrode show that only the absorbance of the MTsPc monomer contributes to a photocurrent while that of the MTsPc face to face dimer does not generate a photocurrent.展开更多
A photoelectrochemical process in the degradation of an azodye (Acid Orange II) on a Pt/TiO 2 film electrode was investigated. By using the glass device and the voltage stabilized source of direct current, decoloriza...A photoelectrochemical process in the degradation of an azodye (Acid Orange II) on a Pt/TiO 2 film electrode was investigated. By using the glass device and the voltage stabilized source of direct current, decolorization ratios higher than 78% were observed during a period of 5h. Comparing this value with the sum of the decolorization ratios obtained by a sole application of electrochemical(lower than 3%) and photochemical(about 23%) procedures, a significant synergic effect between both processes was observed. The effects of adscititious voltage and pH value on the decolorization ratios were obvious while the effect of the amount of aeration was minor.展开更多
A dye-sensitized nanocrystalline TiO 2 solar cell(DYSC) was assembled, of which counter electrode was modified already by platinum, nickel and carbon. It was found that the DYSC had better photoelectric performanc...A dye-sensitized nanocrystalline TiO 2 solar cell(DYSC) was assembled, of which counter electrode was modified already by platinum, nickel and carbon. It was found that the DYSC had better photoelectric performance when the electrode was modified by platinum than by nickel and carbon. The influence of the incidence light wavelength on the incidence monochromatic photoelectric conversion efficiency(IPCE) was investigated. The result shows that the IPCE mainly depends on the short-circuit current density(I SC) of a DYSC, and the IPCE reaches 48.32% under the irradiation with the wavelength of 560 nm when the counter electrode of a DYSC was modified by platinum. The influence of incident light intensity on the photoelectric properties of a DYSC was also investigated. It was found that the I SC and open-circuit voltage(V OC) increased and the fill factor(f f) of the DYSC decreased with the increase of the incident light intensity.展开更多
Composite nanoporous electrode SnO2/TiO2 was fabricated for the dye sensitized solar cell (DSSC) with N3 (Cis-Ru). After introducing of TiO2, the open-circuit photovoltage (Voc) was higher than that of the pure SnO2 ...Composite nanoporous electrode SnO2/TiO2 was fabricated for the dye sensitized solar cell (DSSC) with N3 (Cis-Ru). After introducing of TiO2, the open-circuit photovoltage (Voc) was higher than that of the pure SnO2 electrode, while short-circuit photocurrent (Isc) was varied with the ratio of the TiO2. Appropriate content of the TiO2 can be beneficial to the efficiency of the solar cell, and it gives negative impact on the composite electrode when the content of TiO2 is higher.展开更多
The degradation of ethinylestradiol (EE, an orally bio-active estrogen) in an aqueous-methanolic solution using a Ti/TiO2 thin-film electrode and UV radiation (a photoelectrocatalytic system) was evaluated. Hence, HPL...The degradation of ethinylestradiol (EE, an orally bio-active estrogen) in an aqueous-methanolic solution using a Ti/TiO2 thin-film electrode and UV radiation (a photoelectrocatalytic system) was evaluated. Hence, HPLC/UV analysis shows that EE (at 0.34 mmol) is totally consumed after 30 minutes of exposure to the photoelectrocatalytic system in the presence of Na2SO4 (0.1 mol·L-1) and with an applied bias potential of +1.0 V versus the Ag/AgCl reference electrode. Moreover, monitoring by direct infusion electrospray ionization mass spectrometry (ESI-MS) and SPME-GC/ MS (solid phase microextraction coupled with gas chromatography-mass spectrometry) reveals that apparently no degradation products are formed under these conditions. Hence, this study demonstrates that the photoelectrocatalytic system can be efficiently used to promote the complete degradation (and likely mineralization) of this hormone under these conditions.展开更多
Nano sized powders of TiO2 （titanium dioxide） and Nb2O5 （Niobium （V） oxide） were used to fabricate TiO2/Nb2O5 composites thin films by EPD （electrophoretic deposition） technique. The metal oxide powders, toget...Nano sized powders of TiO2 （titanium dioxide） and Nb2O5 （Niobium （V） oxide） were used to fabricate TiO2/Nb2O5 composites thin films by EPD （electrophoretic deposition） technique. The metal oxide powders, together with magnesium nitrate hexahydrate pellets, were suspended in propan-2-ol inside an EPD cell. The electrodes, placed 1.2 cm apart, were partially immersed in the suspension and a DC potential applied across them. Key EPD process parameters, which include applied DC electric field, deposition time and solid concentration in suspension, were optimized through visual inspection and from UV-Vis-NIR spectrophotometer spectra. The highest （55%） transmittance was obtained for films with deposition time of 90 s, powder concentration of 0.01 g/40 mL, and 35 V DC （direct current） voltage. XRD micrographs confirmed that TiO2 and Nb2O5 particles were presented in the composite film. SEM （scanning electron microscope） micrographs of the composite electrode thin films showed that porous films of high quality with well controlled morphology were deposited by using the EPD technique.展开更多
Particular kinds of TiO2 nanocrystalline electrodes were sensitized by aluminum phthalocyanines modified with sulfonate groups [ Al（OH） PcSm ]. It was found that in the red region, the electrodes show obvious photoe...Particular kinds of TiO2 nanocrystalline electrodes were sensitized by aluminum phthalocyanines modified with sulfonate groups [ Al（OH） PcSm ]. It was found that in the red region, the electrodes show obvious photoelectrical responses. The surface photovoltage spectra and photocurrent action spectra indicate that in the red region, the monomers of aluminum phthalocyanines have a greater influence on the determination of the photoelectrical response of TiO2 electrodes than the dimers. The dye-sensitized solar cells were obtained by using the aluminum phthalocyaninessensitized TiO2 electrodes and Pt electrodes, which have an open circuit photovoltage of 360 mV, a short circuit photocurrent of 39. 4 μA/cm^2 , a fill factor of 0. 54 and a maximum power output of 7.65 μW/cm^2 under a light intensity of 50 mW/cm^2.展开更多
The microporous nanocry'sta1line TiO2 electrode with large surface roughness factor hasbeen prepared on a conducting glass support. Modification of the TiO2 electrode by in situ preparingquantum sized RuS2 particl...The microporous nanocry'sta1line TiO2 electrode with large surface roughness factor hasbeen prepared on a conducting glass support. Modification of the TiO2 electrode by in situ preparingquantum sized RuS2 particles on the surface of TiO2 electrode extends the optical absorptionspectrum and photocurrent action specmim into visible region. In addition, compared with RuS2 bulknlaterials- a blue shifi in both absorption spectrum and photocurrent action speCtrum of RuS2rriO2elcctrode is obserived and explained in terms of quantum sized effect.展开更多
The preparation and study of supported TiO2 for photocatalytic application in solar cell devices is a relevant research field. Thin films of TiO2 prepared on Ti by thermal oxidation in a wide range of temperatures (45...The preparation and study of supported TiO2 for photocatalytic application in solar cell devices is a relevant research field. Thin films of TiO2 prepared on Ti by thermal oxidation in a wide range of temperatures (450°C - 900°C) were characterized by electrochemical impedance spectroscopy, potentiometry and amperometry. This material presents photoelectrochemical activity, which depends dramatically of the oxidation temperature and the exposition time at the studied temperatures. The flatband potential as well as the donor density and the resistance to the charge transfer were measured. All these parameters are temperature dependent, and the optimal values are observed on the photoelectrodes prepared at 750°C. This result is consistent with the photochemical response reported in the literature for thin films of Ti/TiO2 prepared under similar conditions.展开更多
基金supported by the National Natural Science Foundation of China(21507104)the Fundamental Research Funds for the Central Universities of China
文摘Electrochemical oxidation of aniline in aqueous solution was investigated over a novel Ti/TiOxHy/Sb-SnO2 electrode prepared by the electrodeposition method.Scanning electron microscopy,X-ray diffraction,and electrochemical measurements were used to characterize its morphology,crystal structure,and electrochemical properties.Removal of aniline by the Ti/TiOxHy/Sb-SnO2electrode was investigated by ultraviolet-Visible spectroscopy and chemical oxygen demand（COD）analysis under different conditions,including current densities,initial concentrations of aniline,pH values,concentrations of chloride ions,and types of reactor.It was found that a higher current density,a lower initial concentration of aniline,an acidic solution,the presence of chloride ions（0.2wt%NaCl）,and a three-dimensional（3D） reactor promoted the removal efficiency of aniline.Electrochemical degradation of aniline followed pseudo-first-order kinetics.The aniline（200 mL of 100mg·L-（-1）） and COD removal efficiencies reached 100%and 73.5%,respectively,at a current density of 20 mA·cm-（-2）,pH of 7.0,and supporting electrolyte of 0.5 wt%Na2SO4 after 2 h electrolysis in a 3D reactor.These results show that aniline can be significantly removed on the Ti/TiOxHy/Sb-SnO2electrode,which provides an efficient way for elimination of aniline from aqueous solution.
基金Project supported by the Institute of Environmental Engineering,Peking University and China Postdoctoral Science Foundation(No.2005037032)
文摘Ti/Sb-SnO2 anodes were prepared by thermal decomposition to examine the influence of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol. The physicochemical properties of the Sb-SnO2 coating were markedly influenced by different amounts of Sb dopant. The electrodes, which contained 5% Sb dopant in the coating, presented a much more homogenous surface and much smaller mud-cracks, compared with Ti/Sb-SnO2 electrodes containing 10% or 15% Sb dopant, which exibited larger mud cracks and pores on the surface. However, the main microstructure remained unchanged with the addition of the Sb dopant. No new crystal phase was observed by X-ray diffraction （XRD）. The electrochemical oxidation of 4-chlorophenol on the Ti/SnO2 electrode with 5% Sb dopant was inclined to electrochemical combustion; while for those containing more Sb dopant, intermediate species were accumulated. The electrodes with 5% Sb dopant showed the highest efficiency in the bulk electrolysis of 4-chlorophenol at a current density of 20 mA/cm^2 for 180 min; and the removal rates of 4-chlorophenol and COD were 51.0% and 48.9%, respectively.
基金National Natural Science Foundation of China with Grant No.21905304Natural Science Foundation of Shandong Province(No.ZR2019BEM031)the Fundamental Research Funds for the Central Universities(Nos.18CX02158A and 19CX05001A).
文摘Ti3C2Tx,a novel two-dimensional layer material,is widely used as electrode materials of supercapacitor due to its good metal conductivity,redox reaction active surface,and so on.However,there are many challenges to be addressed which impede Ti3C2Tx obtaining the ideal specific capacitance,such as restacking,re-crushing,and oxidation of titanium.Recently,many advances have been proposed to enhance capacitance performance of Ti3C2Tx.In this review,recent strategies for improving specific capacitance are summarized and compared,for example,film formation,surface modification,and composite method.Furthermore,in order to comprehend the mechanism of those efforts,this review analyzes the energy storage performance in different electrolytes and influencing factors.This review is expected to predict redouble research direction of Ti3C2Tx materials in supercapacitors.
基金the Fund of the Natural Science of Guangxi (0731015)
文摘Praseodymium was selected as a promoter for SnO2/Ti electrode to improve the electrocatalytic performance by electrodeposition in pharmaceutical wastewater treatment; the micrograph and the structure were characterized by SEM and XRD. Mixture uniform design was used in the optimization of the electrolytic conditions; mathematical model was established according to the rate of wiping COD off, which revealed the relationship between the current intensity, time of electrolysis, the amount of doped Pr, and the ratio of area （SnOJTi：Al）. On the basis of the analysis of the empirical model, the optimized parameters had been obtained; the rate of wiping COD off was up to 94.9%, it decreased from 392 to 20 mg/L. Experimental results showed that the electrocatalytic performance of the electrode doped with Pr was superior for the treatment of pharmaceutical wastewater.
基金supported by the National Science Foundation for Innovative Research Group of China(No.51121003)the Specialized Research Fund for the Doctoral Program of Higher Education of China(No.20110003110023)the special fund of State Key Joint Laboratory of Environment Simulation and Pollution Control of China
文摘Electrochemicaldegradation of2,4-dichlorophenol （2,4-DCP） in aqueous solutionwas investigated over Ti/SnO2-Sb anode. The factors influencing thedegradation rate, such as applied currentdensity （2-40 mA/cm2 ）, pH （3-11） and initial concentration （5-200 mg/L）were evaluated. Thedegradation of2,4-DCP followed apparent pseudo first-order kinetics. Thedegradation ratio on Ti/SnO2 -Sb anode attained 〉 99.9% after 20 min of electrolysis at initial 5-200 mg/L concentrations at a constant currentdensity of 30 mA/cm2 with a 10 mmol/L sodium sulphate （Na2SO4 ） supporting electrolyte solution. The results showed that 2,4-DCP （100 mg/L）degradation and total organic carbon （TOC） removal ratio achieved 99.9% and 92.8%, respectively, at the optimal conditions after 30 min electrolysis. Under this condition, thedegradation rate constant （k） and thedegradation half-life （t1/2 ）were 0.21 min1 and （2.8 ± 0.2） min, respectively. Mainly carboxylic acids （propanoic acid, maleic acid, propanedioic acid, acetic acid and oxalic acid） weredetected as intermediates. The energy efficiencies for2,4-DCPdegradation （5-200 mg/L）with Ti/SnO2-Sb anode ranged from 0.672 to 1.602 g/kWh. The Ti/SnO2-Sb anodewith a high activity to rapid organic oxidation could be employed todegrade chlorophenols, particularly2,4-DCP inwastewater.
文摘The electrochemical behavior of vitamin C（ascorbic acid or AA） is investigated on the surface of a carbon-paste electrode modified with TiO2 nanoparticles and 2,2＇-（1,2 butanediylbis（nitriloethylidyne））-bis-hydroquinone（BBNBH）.The prepared modified electrode showed an efficient catalytic role in the electrochemical oxidation of AA,leading to remarkable decrease in oxidation overpotential and enhancement of the kinetics of the electrode reaction.This modified electrode exhibits well-separated oxidation peaks for AA and uric acid（UA）.The modified electrode is successfully applied for the accurate determination of AA in pharmaceutical preparations.
基金supported by the Major State Basic Research Development Program of China (No.2006CB202605)the National Natural Science Foundation of China (No.50473055)
文摘The ZnO-modified TiO2 electrode was prepared by adding Zn（CH3COO）2·2H2O to the TiO2 colloid during the sol-gel production process, and was used in dye-sensitized solar cells （DSCs）. The open circuit voltage （Voc） and fill factor （if） of the cells were improved sig- nificantly. The performances of the ZnO-modified TiO2 electrode such as dark current, transient photocurrent, impedance, absorption spectra, and fiat band potential （Vfb） were investigated. It is found that the interface charge recombination impedance increases and Vfb shifts about 200 mV toward the cathodic potential. The effect mechanism of ZnO modification on the performance of DSCs may be that ZnO occupies the surface states of the TiO2 film.
基金Thanks to the financial support from the Science and technology project of Shaanxi Province(2017ZDXM-GY-041).
文摘Regulation of the electronic structure and interface property becomes a major strategy in the preparation of electrocatalyst.This paper reports the synthesis of cerium(Ce)and sodium dodecyl benzene sulfonate(SDBS)comodified Ti/PbO_(2)electrodes(Ti/PbO2CeSDBS).Ce and SDBS could greatly change the electronic structure and interface property of PbO2.Ti/PbO_(2)CeSDBS exhibited excellent electrocatalytic activity and stability in Rhodamine B(RhB)electrocatalytic oxidation reaction.The improved electrocatalytic activity associates with the synergistic effect of electronic and interface factors.In the electrochemical degradation of RhB,the removal efficiencies of RhB and COD are about 0.880 and 0.694 respectively after the electrolysis of 220 min with Ti/PbO_(2)Ce4SDBS40,which are higher than the contrast Ti/PbO_(2)electrodes.In the meantime,the accelerated lifetime of Ti/PbO_(2)Ce4SDBS40 is more than 6.2 times than that of Ti/PbO_(2).
基金supported by the National Natural Science Foundation of China (Nos. 21277134, 21107103)the State Key Laboratory of Environmental, Criteria and Risk Assessment Chinese Research Academy of Environmental Sciences
文摘TiO2 nanotube （TINT） electrodes anodized in fluorinated organic solutions were successfully prepared on Ti sheets. Field-emission scanning electron microscopy （FE-SEM） and X-ray diffraction （XRD） were performed to characterize the TiNT electrodes. The linear voltammetry results under irradiation showed that the TiNT electrode annealed at 450℃ presented the highest photoelectrochemical activity. By combining photocatalytic with electrochemical process, a significantly synergetic effect on ammonia degradation was observed with Na2SO4 as supporting electrolyte at pH 10.7. Furthermore, the photoelectrocatalytic efficiency on the ammonia degradation was greatly enhanced in presence of chloride ions without the limitation ofpH. The degradation rate was improved by 14.8 times reaching 4.98 × 10^-2 min^-1 at pH 10.7 and a faster degradation rate of 6.34 × 10^-2 min^-1 was obtained at pH 3.01. The in situ photoelectrocatalytic generated active chlorine was proposed to be responsible for the improved efficiency. On the other hand, an enhanced degradation of ammonia using TiNT electrode fabricated in fluorinated organic solution was also confirmed compared to TiNT electrode anodized in fluorinated water solution and TiO2 film electrode fabricated by sol-gel method. Finally, the effect of chloride concentration was also discussed.
基金financially supported by the National Natural Science Foundation of China (No. 51364024 and 51404124)Gansu Province Department of Education Fund (No. 2013A-029)the Foundation of State Key Laboratory of Gansu Advanced Nonferrous Metal Materials (Nos. SKL 1316 and SKL 1314)
文摘Ti/SnO2–Sb electrode has a good effect on the removal of organic pollutants. But its short service life limits its large-scale application in industry. Electro-catalytic degradation performances and service life of the electrode can be significantly improved by doping rare earth（RE） ions into the oxide coating of Ti/SnO2–Sb electrode. Ti/SnO2–Sb electrodes doped with different RE elements（Ce, Dy, La, and Eu） were prepared by the thermal decomposition method at 550 ℃. Electro-catalytic degradation performances of electrodes doped with different RE elements were evaluated by linear sweep voltammetry（LSV） and Tafel curves. During the electrolysis,the conversion of p-nitrophenol was performed with these electrodes as anodes under galvanostatic control. The structures and morphologies of the surface coating of the electrodes were characterized by scanning electron microscope（SEM）. The results demonstrate that the electro-catalytic degradation performances of Ti/SnO2–Sb electrodes are improved to different levels by doping different RE ions. Improved Ti/SnO2–Sb electrodes by the introduction of different RE have higher oxygen evolution potential, better electro-catalysis ability, better coverage,and longer electrode life.
基金supported by the National Natural Science Foundation of China (No. 51178138)the National Creative Research Groups of China (No. 51121062)the State Key Laboratory of Urban Water Resources and Environment (No. 2010DX03)
文摘Pd-MnO2/TiO2 nanotube arrays（NTAs） photo-electrodes were successfully fabricated via anodization and electro deposition subsequently; the obtained Pd-MnO2/TiO2 NTAs photo electrodes were analyzed by scanning electron microscopy（SEM）, X-ray diffraction（XRD） and characterized accordingly. Moreover, the light harvesting and absorption properties were investigated via ultraviolet–visible diffuse reflectance spectrum（DRS）; photo degradation efficiency was investigated via analyzing the photo catalytic degradation of Rhodamine B under visible illumination（xenon light）. The performed analyses illustrated that Pd-MnO2 codoped particles were successfully deposited onto the surface of the TiO2 nanotube arrays;DRS results showed significant improvement in visible light absorption which was between400 and 700 nm. Finally, the photo catalytic degradation efficiency results of the designated organic pollutant（Rhodamine B） illustrated a superior photocatalytic（PC） efficiency of approximately 95% compared to the bare TiO2 NTAs, which only exhibited a photo catalytic degradation efficiency of approximately 61%, thus it indicated the significant enhancement of the light absorption properties of fabricated photo electrodes and their yield of UOH radicals.
文摘Tetrasulfonated Zn,Co,Ga,In,TiO and metal free phthalocyanine (MTsPc) mainly exist as dimers on the nanostructured TiO 2 electrode and mostly exist as monomers in dimethyl sulfoxide. The photocurrent action spectra of the liquid junction based on the MTsPc/TiO 2 nanostructured electrode show that only the absorbance of the MTsPc monomer contributes to a photocurrent while that of the MTsPc face to face dimer does not generate a photocurrent.
文摘A photoelectrochemical process in the degradation of an azodye (Acid Orange II) on a Pt/TiO 2 film electrode was investigated. By using the glass device and the voltage stabilized source of direct current, decolorization ratios higher than 78% were observed during a period of 5h. Comparing this value with the sum of the decolorization ratios obtained by a sole application of electrochemical(lower than 3%) and photochemical(about 23%) procedures, a significant synergic effect between both processes was observed. The effects of adscititious voltage and pH value on the decolorization ratios were obvious while the effect of the amount of aeration was minor.
基金Supported by the National Natural Science Foundation of China(No. 5 0 0 82 0 0 3,5 0 372 0 2 2 ) and the Natural ScienceFoundation of Fujian Province,China(No. 2 0 0 1I0 0 6,E0 2 10 0 2 3)
文摘A dye-sensitized nanocrystalline TiO 2 solar cell(DYSC) was assembled, of which counter electrode was modified already by platinum, nickel and carbon. It was found that the DYSC had better photoelectric performance when the electrode was modified by platinum than by nickel and carbon. The influence of the incidence light wavelength on the incidence monochromatic photoelectric conversion efficiency(IPCE) was investigated. The result shows that the IPCE mainly depends on the short-circuit current density(I SC) of a DYSC, and the IPCE reaches 48.32% under the irradiation with the wavelength of 560 nm when the counter electrode of a DYSC was modified by platinum. The influence of incident light intensity on the photoelectric properties of a DYSC was also investigated. It was found that the I SC and open-circuit voltage(V OC) increased and the fill factor(f f) of the DYSC decreased with the increase of the incident light intensity.
文摘Composite nanoporous electrode SnO2/TiO2 was fabricated for the dye sensitized solar cell (DSSC) with N3 (Cis-Ru). After introducing of TiO2, the open-circuit photovoltage (Voc) was higher than that of the pure SnO2 electrode, while short-circuit photocurrent (Isc) was varied with the ratio of the TiO2. Appropriate content of the TiO2 can be beneficial to the efficiency of the solar cell, and it gives negative impact on the composite electrode when the content of TiO2 is higher.
文摘The degradation of ethinylestradiol (EE, an orally bio-active estrogen) in an aqueous-methanolic solution using a Ti/TiO2 thin-film electrode and UV radiation (a photoelectrocatalytic system) was evaluated. Hence, HPLC/UV analysis shows that EE (at 0.34 mmol) is totally consumed after 30 minutes of exposure to the photoelectrocatalytic system in the presence of Na2SO4 (0.1 mol·L-1) and with an applied bias potential of +1.0 V versus the Ag/AgCl reference electrode. Moreover, monitoring by direct infusion electrospray ionization mass spectrometry (ESI-MS) and SPME-GC/ MS (solid phase microextraction coupled with gas chromatography-mass spectrometry) reveals that apparently no degradation products are formed under these conditions. Hence, this study demonstrates that the photoelectrocatalytic system can be efficiently used to promote the complete degradation (and likely mineralization) of this hormone under these conditions.
文摘Nano sized powders of TiO2 （titanium dioxide） and Nb2O5 （Niobium （V） oxide） were used to fabricate TiO2/Nb2O5 composites thin films by EPD （electrophoretic deposition） technique. The metal oxide powders, together with magnesium nitrate hexahydrate pellets, were suspended in propan-2-ol inside an EPD cell. The electrodes, placed 1.2 cm apart, were partially immersed in the suspension and a DC potential applied across them. Key EPD process parameters, which include applied DC electric field, deposition time and solid concentration in suspension, were optimized through visual inspection and from UV-Vis-NIR spectrophotometer spectra. The highest （55%） transmittance was obtained for films with deposition time of 90 s, powder concentration of 0.01 g/40 mL, and 35 V DC （direct current） voltage. XRD micrographs confirmed that TiO2 and Nb2O5 particles were presented in the composite film. SEM （scanning electron microscope） micrographs of the composite electrode thin films showed that porous films of high quality with well controlled morphology were deposited by using the EPD technique.
基金Supported by the National Natural Science Foundation of China(Nos. 60271020 and 20125513)
文摘Particular kinds of TiO2 nanocrystalline electrodes were sensitized by aluminum phthalocyanines modified with sulfonate groups [ Al（OH） PcSm ]. It was found that in the red region, the electrodes show obvious photoelectrical responses. The surface photovoltage spectra and photocurrent action spectra indicate that in the red region, the monomers of aluminum phthalocyanines have a greater influence on the determination of the photoelectrical response of TiO2 electrodes than the dimers. The dye-sensitized solar cells were obtained by using the aluminum phthalocyaninessensitized TiO2 electrodes and Pt electrodes, which have an open circuit photovoltage of 360 mV, a short circuit photocurrent of 39. 4 μA/cm^2 , a fill factor of 0. 54 and a maximum power output of 7.65 μW/cm^2 under a light intensity of 50 mW/cm^2.
文摘The microporous nanocry'sta1line TiO2 electrode with large surface roughness factor hasbeen prepared on a conducting glass support. Modification of the TiO2 electrode by in situ preparingquantum sized RuS2 particles on the surface of TiO2 electrode extends the optical absorptionspectrum and photocurrent action specmim into visible region. In addition, compared with RuS2 bulknlaterials- a blue shifi in both absorption spectrum and photocurrent action speCtrum of RuS2rriO2elcctrode is obserived and explained in terms of quantum sized effect.
文摘The preparation and study of supported TiO2 for photocatalytic application in solar cell devices is a relevant research field. Thin films of TiO2 prepared on Ti by thermal oxidation in a wide range of temperatures (450°C - 900°C) were characterized by electrochemical impedance spectroscopy, potentiometry and amperometry. This material presents photoelectrochemical activity, which depends dramatically of the oxidation temperature and the exposition time at the studied temperatures. The flatband potential as well as the donor density and the resistance to the charge transfer were measured. All these parameters are temperature dependent, and the optimal values are observed on the photoelectrodes prepared at 750°C. This result is consistent with the photochemical response reported in the literature for thin films of Ti/TiO2 prepared under similar conditions.
