Dielectric elastomer actuator （DEA） show promise for mechatronic applications due to the advantages of dielectric elastomer, such as lightweight, flexible, low cost, high strain, etc, and many configurations of DEAs...Dielectric elastomer actuator （DEA） show promise for mechatronic applications due to the advantages of dielectric elastomer, such as lightweight, flexible, low cost, high strain, etc, and many configurations of DEAs have been demonstrated. As a kind of linear actuator, cone DEAs are studied in some laboratory prototypes due to easy manufacturing, however, their performance have not been exploited fully. Based on the working principle of DEA, a four-bar linkage mechanism is designed to provide negative stiffness preload, which can increase displacement output of actuator （outer diameter 100 mm） to 17 mm. Three cone actuating units are assembled in parallel to enhance the maximum force output to 5.07 N. Loading experiments of actuator in forward and backward strokes are performed, the experimental results show that backward stroke has stronger actuating capability than forward stroke, accordingly application of actuator is recommended. Four factors rather than applied voltage, i.e., number of actuating units, pre-stretch ratio, inner diameter, and outer diameter, are determined as influencing factors for Taguchi method. Then the performance objectives of actuator, i.e., displacement output, maximum force output, and maximum work in backward stroke, are investigated based on L9（34） Taguchi orthogonal design. The mean signal-to-noise （S/N） ratio based on the larger-the-better criterion is calculated according to the acquired displacement and force output. Analytical results show that outer diameter has the most significant influence on displacement output, and maximum force out and work output are influenced most by number of actuating units. Inner diameter also has an important effect on the performance objectives of actuator, while pre-stretch ratio has the least influence. The proposed performance investigation is helpful for the design and application of cone actuator in mechatronic system.展开更多
Target assembly is a key consumable material for producing thin fi lm used in the electronic packaging and devices. The residual stresses induced during the process of soldering are detrimental to the performance of t...Target assembly is a key consumable material for producing thin fi lm used in the electronic packaging and devices. The residual stresses induced during the process of soldering are detrimental to the performance of target assembly. In this work, the intensity and distribution of the soldering residual stress of Co/In/Cu target assembly subjected to a 20 W/(m^2 K) cooling condition corresponding to the actual air cooling process were studied, based on fi nite element simulation and Taguchi method, to optimize the sputtering target assembly. Effects of different control factors, including solder material, thickness of solder layer, target and backing plate, on the soldering residual stress of target assembly are investigated. The maximum residual stress is calculated as 9.28 MPa in the target located at 0.16 mm from target–solder layer interface and at a distance of 0.78 mm from symmetry axis. The optimal design in target assembly has the combination of indium solder material, cobalt target at 12 mm thick, solder layer at 0.8 mm thick, copper backing plate at 15 mm thick. Moreover, solder material is the most important factor among control factors in the target assembly.展开更多
Chemical mechanical polishing （CMP） was used to polish Lithium triborate （LiB3O5 or LBO） crystal. Taguchi method was applied for optimization of the polishing parameters. Material removal rate （MRR） and surface ...Chemical mechanical polishing （CMP） was used to polish Lithium triborate （LiB3O5 or LBO） crystal. Taguchi method was applied for optimization of the polishing parameters. Material removal rate （MRR） and surface roughness are considered as criteria for the optimization. The polishing pressure, the abrasive concentration and the table velocity are important parameters which influence MRR and surface roughness in CMP of LBO crystal. Experiment results indicate that for MRR the polishing pressure is the most significant polishing parameter followed by table velocity; while for the surface roughness, the abrasive concentration is the most important one. For high MRR in CMP of LBO ctystal the optimal conditions are： pressure 620 g/cm^2, concentration 5.0 wt pct, and velocity 60 r/min, respectively. For the best surface roughness the optimal conditions are： pressure 416 g/cm^2, concentration 5.0 wt pct, and velocity 40 r/min, respectively. The contributions of individual parameters for MRR and surface roughness were obtained.展开更多
An efficient approach was introduced for improving the condition of major controlled rolling process pa- rameters of roughing, finishing and coiling temperatures and optimizing these parameters to obtain minimum grain...An efficient approach was introduced for improving the condition of major controlled rolling process pa- rameters of roughing, finishing and coiling temperatures and optimizing these parameters to obtain minimum grain size and maximum dome height simultaneously. Taguchi method combined with grey relational analysis was applied to achieve optimum grain size and dome height during controlled rolling process. For this purpose, four levels for the above temperatures were chosen and sixteen experiments were conducted based on orthogonal array of Taguchi meth- od. Based on Taguchi approach, signal-to-noise （S/N） ratios were calculated and used in order to obtain the opti- mum levels for every input parameter. Analysis of variance revealed that finishing and coiling temperatures have the maximum effect on the grain size and dome height of microalloyed steels. The confirmation tests with the optimal levels of parameters indicated that the grain size and dome height of controlled rolled microalloyed steels can be im- proved effectively through this approach.展开更多
The neutral zinc sulfate solution obtained from hydrometallurgical process of Angouran zinc concentrate has cadmium, nickel and cobalt impurities, that must be purified before electrowinning. Therefore, cadmium and ni...The neutral zinc sulfate solution obtained from hydrometallurgical process of Angouran zinc concentrate has cadmium, nickel and cobalt impurities, that must be purified before electrowinning. Therefore, cadmium and nickel are usually cemented out by addition of zinc dust and remained nickel and cobalt cemented out at second stage with zinc powder and arsenic trioxide. In this research, a new approach is described for determination of effective parameters and optimization of zinc electrolyte hot purification process using statistical design of experiments. The Taguchi method based on orthogonal array design（OAD） has been used to arrange the experimental runs. The experimental conditions involved in the work are as follows： the temperature range of 70-90 ℃ for reaction temperature（T）, 30-90 min for reaction time（t）, 2-4 g/L for zinc powder mass concentration（M）, one to five series for zinc dust particle size distributions（S1-S5）, and 0.1-0.5 g/L（C） for arsenic trioxide mass concentration. Optimum conditions for hot purification obtained in this work are T4（85 ℃）, t4=75 min, M4=3.5 g/L, S4（Serie 4）, and C2=0.2 g/L.展开更多
A series of different transition metals(V,Co,Cr,Mn,Fe,Ni,Cu and Zn) promoted H-ZSM-5 catalysts were prepared by impregnation method and characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and tra...A series of different transition metals(V,Co,Cr,Mn,Fe,Ni,Cu and Zn) promoted H-ZSM-5 catalysts were prepared by impregnation method and characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The catalytic activity of these catalysts was evaluated for the selective catalytic reduction(SCR) of NO with NH_3 as reductant in the presence of oxygen.The results revealed that the catalytic activity of Cu-ZSM-5 nanocatalyst for NO conversion to N_2 was 80%at 300 ℃,which was the best among various promoted metals.Design of experiments(DOEs) with Taguchi method was employed to optimize NH_3-SCR process parameters such as NH_3/NO ratio,O_2 concentration,and gas hourly space velocity(GHSV) over Cu-ZSM-5 nanocatalyst at 250 and 300 ℃.Results showed that the most important parameter in NH_3-SCR of NO is O_2 concentration;followed by NH_3/NO ratio and GHSV has little importance.The NO conversion to N_2 of 63.1%and 94.86%was observed at 250℃ and 300℃,respectively under the obtained optimum conditions.展开更多
This study aims to examine the usability of environmentally harmless vegetable oil in the minimum quantity of lubrication(MQL)system in face milling of AISI O2 steel and to optimize the cutting parameters by different...This study aims to examine the usability of environmentally harmless vegetable oil in the minimum quantity of lubrication(MQL)system in face milling of AISI O2 steel and to optimize the cutting parameters by different statistical methods.Vegetable oil was preferred as cutting fluid,and Taguchi method was used in the preparation of the test pattern.After testing with the prepared test pattern,cutting performance in all parameters has been improved according to dry conditions thanks to the MQL system.The highest tool life was obtained by using cutting parameters of 7.5 m cutting length,100 m/min cutting speed,100 mL/h MQL flow rate and 0.1 mm/tooth feed rate.Optimum cutting parameters were determined according to the Taguchi analysis,and the obtained parameters were confirmed with the verification tests.In addition,the optimum test parameter was determined by applying the gray relational analysis method.After using ANOVA analysis according to the measured surface roughness and cutting force values,the most effective cutting parameter was observed to be the feed rate.In addition,the models for surface roughness and cutting force values were obtained with precisions of 99.63%and 99.68%,respectively.Effective wear mechanisms were found to be abrasion and adhesion.展开更多
Fiber optic displacement sensors are widely used in industry. Retro reflective fiber optic displacement sensor consists of parallel fibers with a reflector at a distance. Light is launched into the transmitting fiber ...Fiber optic displacement sensors are widely used in industry. Retro reflective fiber optic displacement sensor consists of parallel fibers with a reflector at a distance. Light is launched into the transmitting fiber which gets reflected by reflector. This reflected light is collected by the receiving fiber. The received light is function of the displacement of the reflector from the fiber end faces. This paper is targeted to obtain a robust design for the fiber optic displacement sensor (FODS) using well known Taguchi method. The design takes care of all noise parameters within constraints of manufacturing tolerances. The statistical data analysis is performed on the simulated results. The larger the better signal to noise quality characteristics is used to find the effect of control parameters in the data analysis. Taguchi analysis suggests dominant parameters, which affects the sensitivity of the FODS and causes immunity to noise. A source fiber inclination angle is chosen as an adjustment parameter. Other control parameters are used for fine tuning of the FODS design for achieving three qualities viz. best robustness, optimized sensitivity and robustness and best sensitivity.展开更多
Particle swarm optimization （PSO）, like other evolutionary algorithms is a population-based stochastic algorithm inspired from the metaphor of social interaction in birds, insects, wasps, etc. It has been used for f...Particle swarm optimization （PSO）, like other evolutionary algorithms is a population-based stochastic algorithm inspired from the metaphor of social interaction in birds, insects, wasps, etc. It has been used for finding promising solutions in complex search space through the interaction of particles in a swarm. It is a well recognized fact that the performance of evolutionary algorithms to a great extent depends on the choice of appropriate strategy/operating parameters like population size, crossover rate, mutation rate, crossover operator, etc. Generally, these parameters are selected through hit and trial process, which is very unsystematic and requires rigorous experimentation. This paper proposes a systematic based on Taguchi method reasoning scheme for rapidly identifying the strategy parameters for the PSO algorithm. The Taguchi method is a robust design approach using fractional factorial design to study a large number of parameters with small number of experiments. Computer simulations have been performed on two benchmark functionsiRosenbrock function and Griewank functionito validate the approach.展开更多
This study investigated multi-response optimization of the pulse metal active gas-tungsten inert gas( PMAG-TIG) twin arc hybrid root welding process for an optimal parametric combination to yield favorable back bead g...This study investigated multi-response optimization of the pulse metal active gas-tungsten inert gas( PMAG-TIG) twin arc hybrid root welding process for an optimal parametric combination to yield favorable back bead geometry of welded joints using grey relational analysis and Taguchi method.Eighteen experimental runs based on an orthogonal array following the Taguchi method were performed to derive objective functions to be optimized within the experimental domain.The objective functions were selected in relation to parameters of PMAG-TIG twin arc root welding back bead geometry: back bead width to root reinforcement ratio and deposited metal height.The Taguchi approach was followed by grey relational analysis to solve the multi-response optimization problem.The significance of factors on overall quality characteristics of the weld joint was also evaluated quantitatively using analysis of variance.Optimal results were verified through additional experiments,and showed to feasibility of applying grey relation analysis in combination with Taguchi technique for continuous improvement of product quality in the manufacturing industry.展开更多
To find the optimized levels of various casting parameters in the ductile iron casting, various casting defects and the rejection rate were observed from a medium scale foundry. The controlled values of different cast...To find the optimized levels of various casting parameters in the ductile iron casting, various casting defects and the rejection rate were observed from a medium scale foundry. The controlled values of different casting parameters such as pouring temperature, inoculation, carbon equivalent, moisture content, green compression strength, permeability and mould hardness were selected. Three different melts of metal with 0.4wt.%, 0.6wt.%, and 0.8wt.% inoculation （Fe-Si-Mg alloy and post inoculant） were produced using a 1-ton capacity coreless medium frequency induction furnace. L-27 orthogonal array with 3-level settings were chosen for the analysis. Responses for each run were observed. The signal-to-noise （S/N） ratio for each run was calculated using the Taguchi approach, and the optimized levels of different casting parameters were identified based on the SIN ratio. The analysis of variance for the casting acceptance percentage concludes that inoculation is the most significant factor affecting the castings＇ quality with a contribution percentage of 44%; an increase in inoculation results in a significant improvement in acceptance percentage of ductile iron castings. The experiment results showed that with the optimized parameters, the rejection rate was reduced from 16.98% to 6.07%.展开更多
The Taguchi and analysis of variance (ANOVA) methods were applied to investigate the effects of the structural and operational parameters on the heat transfer performance of a vertical sinter cooling packed bed. The a...The Taguchi and analysis of variance (ANOVA) methods were applied to investigate the effects of the structural and operational parameters on the heat transfer performance of a vertical sinter cooling packed bed. The analysed parameters were the gas flow rate, the air inlet temperature, the sinter inlet temperature, the cooling bed diameter and the cooling bed height, all of which contain three levels. The purpose was to improve the heat transfer performance of a vertical sinter cooling bed. A numerical analysis model was established to assess the heat transfer performance with respect to the varying parameters and their different levels. This mathematical model was validated by using data from practical industrial processes. The Taguchi method for the L27 (35) orthogonal design experiment was selected to evaluate the impacts of the design parameters on the heat transfer performance and to acquire the optimum combination of parameters. The analysis of variance was applied to assess the impact weights and the order of significance of the design parameters. The results show that the sinter inlet temperature and cooling bed diameter have great influences and impact the exergy of the wasted heat recovery by 61.65% and 23.31%, respectively. However, the gas flow rate and the air inlet temperature have small effects on the response. Furthermore, the air and sinter inlet temperatures have the most significant impacts on the efficiency of heat transfer by 68.83% and 23.31%, respectively. The optimal parameter combination (A1B1C3D3E3) was obtained, and the optimal results were validated by confirmation tests.展开更多
Mechanical properties of semi-solid casting are dependent on multiple processing parameters,and improper processing parameters will not only reduce mean data but also increase variations.The present study investigated...Mechanical properties of semi-solid casting are dependent on multiple processing parameters,and improper processing parameters will not only reduce mean data but also increase variations.The present study investigated the impact of parameters in slurry preparation and heat treatment on the yield strength and ductility of T6 heat-treated A356 Al-Si alloy using rapid slurry forming(RSF)semi-solid casting.The focus was primarily on the robustness of mechanical properties based on Taguchi design method.By analyzing signal-to-noise ratio and minimum value calculated from-3S,the optimum slurry preparation parameters and heat treatment parameters were determined to be no quench,enthalpy exchange material(EEM)temperature of 140℃,EEM-to-melt ratio of 6mass%,stirring time of 18 s,solution heat treated at 520℃ for 2 h,and ageing heat treated at 190℃ for 6 h.In a small batch validation,the-3S yield strength and-3S elongation reach 256.1 MPa and 5.03% respectively,showing a satisfactory robustness.The hardness and microstructure of heat-treated samples with the best and worst properties were characterized to gain insight into the underlying mechanisms affecting the mean value and variations of mechanical properties.展开更多
With the continuous improvement of permanent magnet(PM)wind generators'capacity and power density,the design of reasonable and efficient cooling structures has become a focus.This paper proposes a fully enclosed s...With the continuous improvement of permanent magnet(PM)wind generators'capacity and power density,the design of reasonable and efficient cooling structures has become a focus.This paper proposes a fully enclosed self-circulating hydrogen cooling structure for a originally forced-air-cooled direct-drive PM wind generator.The proposed hydrogen cooling system uses the rotor panel supports that hold the rotor core as the radial blades,and the hydrogen flow is driven by the rotating plates to flow through the axial and radial vents to realize the efficient cooling of the generator.According to the structural parameters of the cooling system,the Taguchi method is used to decouple the structural variables.The influence of the size of each cooling structure on the heat dissipation characteristic is analyzed,and the appropriate cooling structure scheme is determined.展开更多
Environmental issues like pollution are major threats to human health.Many systems are developed to reduce pollution.In this paper,an optimal mobile robot design to reduce pollution in Green supply chain management sy...Environmental issues like pollution are major threats to human health.Many systems are developed to reduce pollution.In this paper,an optimal mobile robot design to reduce pollution in Green supply chain management system.Green supply chain management involves as similating environmentally and eco-nomically feasible solutions into the supply chain life-cycle.Smartness,advanced technologies,and advanced networks are becoming pillars of a sustainable supply chain management system.At the same time,there is much change happening in the logistics industry.They are moving towards a new logistics model.In the new model,robotic logistics has a vital role.The reasons for this change are the rapid growth of the e-commerce business and the shortage of workers.The advantages of using robotic logistics are reduction in human errors,faster delivery speed,better customer satisfaction,more safety for workers,and high workforce adaptability.A robot with rocker-bogie suspension is a six-wheeled mobile platform that has a distinctive potential to keep all wheels on the ground continuously.It has been designed to traverse rough and uneven terrain by distributing the load over its wheels equally.However,there is a limitation to achieving high-speed mobility against vertical barriers.In this research,an optimal design of product delivery wheeled robots for a sustainable supply chain system is proposed to ensure higher adaptability and maximum stability during climbing staircases.The design parameters of the proposed robot are optimized using Taguchi Method.The aim is to get a smooth trajectory of the robot’s center-of-mass.The proposed approach realizes a robot with much-improved stability which can climb over heights more than the size of the wheel(i.e.,3 times the radius of wheels).The results reveal that the modified rocker-bogie system not only increases the stair-climbing capability but also thwarts instability due to overturning of a wheel of the robot.展开更多
In this paper,a 20kW vehicle built-in permanent magnet synchronous motor is taken as an example,and a magnetic barrier structure is added to the rotor of the motor to solve the uneven saturation problem of the rotor s...In this paper,a 20kW vehicle built-in permanent magnet synchronous motor is taken as an example,and a magnetic barrier structure is added to the rotor of the motor to solve the uneven saturation problem of the rotor side magnetic bridge.This structure improves the air-gap flux density waveform of the motor by influencing the internal magnetic flux path of the motor rotor,thus improving the sine of the no-load back EMF waveform of the motor and reducing the torque ripple of the motor.At the same time,Taguchi method is used to optimize the structural parameters of the added magnetic barrier.In order to facilitate the analysis of its uneven saturation phenomenon and improve the optimization effect,a simple equivalent magnetic network(EMN)model considering the uneven saturation of rotor magnetic bridge is established in this paper,and the initial values of optimization factors are selected based on this model.Finally,the no-load back EMF waveform distortion rate,torque ripple and output torque of the optimized motor are compared and analyzed,and the influence of magnetic barrier structure parameters on the electromagnetic performance of the motor is also analyzed.The results show that the optimized motor can not change the output torque of the motor as much as possible on the basis of reducing the waveform distortion rate of no-load back EMF and torque ripple.展开更多
The application of new soft magnetic materials in permanent magnet motor can effectively reduce the loss of motor and improve the efficiency of motor. Taguchi method is a local multivariable and multi-objective optimi...The application of new soft magnetic materials in permanent magnet motor can effectively reduce the loss of motor and improve the efficiency of motor. Taguchi method is a local multivariable and multi-objective optimization method widely used in various engineering problems, which can effectively improve the efficiency of engineering optimization. In this paper, based on a 25 kW, 1700 r/min three-phase permanent magnet motor, the relevant motor model is established in the finite element simulation software, and the relevant simulation analysis is carried out. Combined with Taguchi method optimization, the local optimal structure scheme is obtained. Through optimization, the motor can maintain high efficiency, reduce the cogging torque of the motor by 53.45%, reduce the torque ripple by 36.79%, and increase the torque generated by the permanent magnet per unit mass by 21.42%. Through this optimization, the overall performance of the motor has been significantly improved. The research content of this paper verifies the feasibility of the application of Taguchi method in the optimization of new soft magnetic material motor, provides a new idea for the optimization design of new soft magnetic material motor, and also provides a certain reference for the local multi-objective optimization of the electromagnetic structure of other similar motors.展开更多
Taguchi method has been employed to investigate the effects of cutting fluids on surface roughness in turning AISI 1330 alloy steel, using manually operated lathe machine. Experiments have been conducted using L<su...Taguchi method has been employed to investigate the effects of cutting fluids on surface roughness in turning AISI 1330 alloy steel, using manually operated lathe machine. Experiments have been conducted using L<sub>27 </sub>(3<sup>4</sup>) orthogonal array and each experiment was repeated three times and each test used a new cutting tool, High Speed Steel (HSS), to ensure accurate readings of the surface roughness. The statistical methods of Signal-to-Noise (S/N) ratio and the Analysis of Variance (ANOVA) were applied to investigate effects of cutting speed, feed rate and depth of cut on surface roughness under different cutting fluids. Minitab 14 software was used to analyze the effect of variables on the surface roughness. Results obtained indicated that optimal variables for the minimum surface roughness were cutting speed of 35 m/min (level 2), feed of 0.124 mm/rev (level 1), depth of cut of 0.3 mm (level 1) and a cutting fluid with a viscosity of 2.898 mm<sup>2</sup>/s (level 3). Hence, the optimal parameters to obtain better surface roughness of the workpiece material were obtained when groundnut oil based cutting fluid was used. Analysis of variance shows that feed rate has the most significant effect on surface roughness.展开更多
Understanding the complex interaction between heat and mass transfer in non-Newtonian microflows is essential for the development and optimization of efficient microfluidic and thermal management systems.This study in...Understanding the complex interaction between heat and mass transfer in non-Newtonian microflows is essential for the development and optimization of efficient microfluidic and thermal management systems.This study investigates the magnetohydrodynamic(MHD)thermosolutal convection of a Casson fluid within an inclined,porous microchannel subjected to convective boundary conditions.The nonlinear,coupled equations governing momentum,energy,and species transport are solved numerically using the MATLAB bvp4c solver,ensuring high numerical accuracy and stability.To identify the dominant parameters influencing flow behavior and to optimize transport performance,a comprehensive hybrid optimization framework—combining a modified Taguchi design,Grey Relational Analysis(GRA),and Principal Component Analysis(PCA)—is proposed.This integrated strategy enables the simultaneous assessment of skin friction,Nusselt number,and Sherwood number,providing a rigorous multi-objective evaluation of system performance.Comparative validation with benchmark results from the literature confirms the accuracy and reliability of the present formulation and its numerical implementation.The results highlight the intricate coupling among flow slip,buoyancy effects,and convective transport mechanisms.Increased slip flow enhances axial velocity,while a higher solutal Biot number intensifies concentration gradients near the channel walls.Conversely,a lower thermal Biot number diminishes the temperature field,indicating weaker heat transfer across the boundaries.PCA results reveal that the first principal component(PC1)accounts for most of the system variance,demonstrating the dominant influence of coupled flow and transport parameters on overall system performance.展开更多
基金supported by National Natural Science Foundation of China (Grant No. 50975139, Grant No. 50605031)Provincial Natural Science Foundation of Jiangsu, China (Grant No. 2008395)+1 种基金Foundation of State Key Laboratory of Robotics, China (Grant No. RLO200912)China Postdoctoral Science Foundation (Grant No. 20080441319, Grant No. 200902684)
文摘Dielectric elastomer actuator （DEA） show promise for mechatronic applications due to the advantages of dielectric elastomer, such as lightweight, flexible, low cost, high strain, etc, and many configurations of DEAs have been demonstrated. As a kind of linear actuator, cone DEAs are studied in some laboratory prototypes due to easy manufacturing, however, their performance have not been exploited fully. Based on the working principle of DEA, a four-bar linkage mechanism is designed to provide negative stiffness preload, which can increase displacement output of actuator （outer diameter 100 mm） to 17 mm. Three cone actuating units are assembled in parallel to enhance the maximum force output to 5.07 N. Loading experiments of actuator in forward and backward strokes are performed, the experimental results show that backward stroke has stronger actuating capability than forward stroke, accordingly application of actuator is recommended. Four factors rather than applied voltage, i.e., number of actuating units, pre-stretch ratio, inner diameter, and outer diameter, are determined as influencing factors for Taguchi method. Then the performance objectives of actuator, i.e., displacement output, maximum force output, and maximum work in backward stroke, are investigated based on L9（34） Taguchi orthogonal design. The mean signal-to-noise （S/N） ratio based on the larger-the-better criterion is calculated according to the acquired displacement and force output. Analytical results show that outer diameter has the most significant influence on displacement output, and maximum force out and work output are influenced most by number of actuating units. Inner diameter also has an important effect on the performance objectives of actuator, while pre-stretch ratio has the least influence. The proposed performance investigation is helpful for the design and application of cone actuator in mechatronic system.
基金supported financially by the National Key R&D Program of China (No. 2017YFB0305501)the National Natural Science Foundation of China (No. 51475220)the China Postdoctoral Science Foundation Funded Project (No. 2016M591464)
文摘Target assembly is a key consumable material for producing thin fi lm used in the electronic packaging and devices. The residual stresses induced during the process of soldering are detrimental to the performance of target assembly. In this work, the intensity and distribution of the soldering residual stress of Co/In/Cu target assembly subjected to a 20 W/(m^2 K) cooling condition corresponding to the actual air cooling process were studied, based on fi nite element simulation and Taguchi method, to optimize the sputtering target assembly. Effects of different control factors, including solder material, thickness of solder layer, target and backing plate, on the soldering residual stress of target assembly are investigated. The maximum residual stress is calculated as 9.28 MPa in the target located at 0.16 mm from target–solder layer interface and at a distance of 0.78 mm from symmetry axis. The optimal design in target assembly has the combination of indium solder material, cobalt target at 12 mm thick, solder layer at 0.8 mm thick, copper backing plate at 15 mm thick. Moreover, solder material is the most important factor among control factors in the target assembly.
基金supported by the National Natural Science Foundation of China(No.50675104 and 50905086)Six High Talent Fund of Jiangsu Province(No.06-D-024)Talent Fund of NUAA(No.S0782-052)
文摘Chemical mechanical polishing （CMP） was used to polish Lithium triborate （LiB3O5 or LBO） crystal. Taguchi method was applied for optimization of the polishing parameters. Material removal rate （MRR） and surface roughness are considered as criteria for the optimization. The polishing pressure, the abrasive concentration and the table velocity are important parameters which influence MRR and surface roughness in CMP of LBO crystal. Experiment results indicate that for MRR the polishing pressure is the most significant polishing parameter followed by table velocity; while for the surface roughness, the abrasive concentration is the most important one. For high MRR in CMP of LBO ctystal the optimal conditions are： pressure 620 g/cm^2, concentration 5.0 wt pct, and velocity 60 r/min, respectively. For the best surface roughness the optimal conditions are： pressure 416 g/cm^2, concentration 5.0 wt pct, and velocity 40 r/min, respectively. The contributions of individual parameters for MRR and surface roughness were obtained.
文摘An efficient approach was introduced for improving the condition of major controlled rolling process pa- rameters of roughing, finishing and coiling temperatures and optimizing these parameters to obtain minimum grain size and maximum dome height simultaneously. Taguchi method combined with grey relational analysis was applied to achieve optimum grain size and dome height during controlled rolling process. For this purpose, four levels for the above temperatures were chosen and sixteen experiments were conducted based on orthogonal array of Taguchi meth- od. Based on Taguchi approach, signal-to-noise （S/N） ratios were calculated and used in order to obtain the opti- mum levels for every input parameter. Analysis of variance revealed that finishing and coiling temperatures have the maximum effect on the grain size and dome height of microalloyed steels. The confirmation tests with the optimal levels of parameters indicated that the grain size and dome height of controlled rolled microalloyed steels can be im- proved effectively through this approach.
文摘The neutral zinc sulfate solution obtained from hydrometallurgical process of Angouran zinc concentrate has cadmium, nickel and cobalt impurities, that must be purified before electrowinning. Therefore, cadmium and nickel are usually cemented out by addition of zinc dust and remained nickel and cobalt cemented out at second stage with zinc powder and arsenic trioxide. In this research, a new approach is described for determination of effective parameters and optimization of zinc electrolyte hot purification process using statistical design of experiments. The Taguchi method based on orthogonal array design（OAD） has been used to arrange the experimental runs. The experimental conditions involved in the work are as follows： the temperature range of 70-90 ℃ for reaction temperature（T）, 30-90 min for reaction time（t）, 2-4 g/L for zinc powder mass concentration（M）, one to five series for zinc dust particle size distributions（S1-S5）, and 0.1-0.5 g/L（C） for arsenic trioxide mass concentration. Optimum conditions for hot purification obtained in this work are T4（85 ℃）, t4=75 min, M4=3.5 g/L, S4（Serie 4）, and C2=0.2 g/L.
基金financial support from University of Tabriz and Iranian Nanotechnology Initiative
文摘A series of different transition metals(V,Co,Cr,Mn,Fe,Ni,Cu and Zn) promoted H-ZSM-5 catalysts were prepared by impregnation method and characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM) and transmission electron microscopy(TEM).The catalytic activity of these catalysts was evaluated for the selective catalytic reduction(SCR) of NO with NH_3 as reductant in the presence of oxygen.The results revealed that the catalytic activity of Cu-ZSM-5 nanocatalyst for NO conversion to N_2 was 80%at 300 ℃,which was the best among various promoted metals.Design of experiments(DOEs) with Taguchi method was employed to optimize NH_3-SCR process parameters such as NH_3/NO ratio,O_2 concentration,and gas hourly space velocity(GHSV) over Cu-ZSM-5 nanocatalyst at 250 and 300 ℃.Results showed that the most important parameter in NH_3-SCR of NO is O_2 concentration;followed by NH_3/NO ratio and GHSV has little importance.The NO conversion to N_2 of 63.1%and 94.86%was observed at 250℃ and 300℃,respectively under the obtained optimum conditions.
文摘This study aims to examine the usability of environmentally harmless vegetable oil in the minimum quantity of lubrication(MQL)system in face milling of AISI O2 steel and to optimize the cutting parameters by different statistical methods.Vegetable oil was preferred as cutting fluid,and Taguchi method was used in the preparation of the test pattern.After testing with the prepared test pattern,cutting performance in all parameters has been improved according to dry conditions thanks to the MQL system.The highest tool life was obtained by using cutting parameters of 7.5 m cutting length,100 m/min cutting speed,100 mL/h MQL flow rate and 0.1 mm/tooth feed rate.Optimum cutting parameters were determined according to the Taguchi analysis,and the obtained parameters were confirmed with the verification tests.In addition,the optimum test parameter was determined by applying the gray relational analysis method.After using ANOVA analysis according to the measured surface roughness and cutting force values,the most effective cutting parameter was observed to be the feed rate.In addition,the models for surface roughness and cutting force values were obtained with precisions of 99.63%and 99.68%,respectively.Effective wear mechanisms were found to be abrasion and adhesion.
文摘Fiber optic displacement sensors are widely used in industry. Retro reflective fiber optic displacement sensor consists of parallel fibers with a reflector at a distance. Light is launched into the transmitting fiber which gets reflected by reflector. This reflected light is collected by the receiving fiber. The received light is function of the displacement of the reflector from the fiber end faces. This paper is targeted to obtain a robust design for the fiber optic displacement sensor (FODS) using well known Taguchi method. The design takes care of all noise parameters within constraints of manufacturing tolerances. The statistical data analysis is performed on the simulated results. The larger the better signal to noise quality characteristics is used to find the effect of control parameters in the data analysis. Taguchi analysis suggests dominant parameters, which affects the sensitivity of the FODS and causes immunity to noise. A source fiber inclination angle is chosen as an adjustment parameter. Other control parameters are used for fine tuning of the FODS design for achieving three qualities viz. best robustness, optimized sensitivity and robustness and best sensitivity.
文摘Particle swarm optimization （PSO）, like other evolutionary algorithms is a population-based stochastic algorithm inspired from the metaphor of social interaction in birds, insects, wasps, etc. It has been used for finding promising solutions in complex search space through the interaction of particles in a swarm. It is a well recognized fact that the performance of evolutionary algorithms to a great extent depends on the choice of appropriate strategy/operating parameters like population size, crossover rate, mutation rate, crossover operator, etc. Generally, these parameters are selected through hit and trial process, which is very unsystematic and requires rigorous experimentation. This paper proposes a systematic based on Taguchi method reasoning scheme for rapidly identifying the strategy parameters for the PSO algorithm. The Taguchi method is a robust design approach using fractional factorial design to study a large number of parameters with small number of experiments. Computer simulations have been performed on two benchmark functionsiRosenbrock function and Griewank functionito validate the approach.
基金supported by the National Natural Science Foundation of China(Grant No.11375038)Science Fund for Creative Research Groups of NSFC(Grant No.51621064)
文摘This study investigated multi-response optimization of the pulse metal active gas-tungsten inert gas( PMAG-TIG) twin arc hybrid root welding process for an optimal parametric combination to yield favorable back bead geometry of welded joints using grey relational analysis and Taguchi method.Eighteen experimental runs based on an orthogonal array following the Taguchi method were performed to derive objective functions to be optimized within the experimental domain.The objective functions were selected in relation to parameters of PMAG-TIG twin arc root welding back bead geometry: back bead width to root reinforcement ratio and deposited metal height.The Taguchi approach was followed by grey relational analysis to solve the multi-response optimization problem.The significance of factors on overall quality characteristics of the weld joint was also evaluated quantitatively using analysis of variance.Optimal results were verified through additional experiments,and showed to feasibility of applying grey relation analysis in combination with Taguchi technique for continuous improvement of product quality in the manufacturing industry.
文摘To find the optimized levels of various casting parameters in the ductile iron casting, various casting defects and the rejection rate were observed from a medium scale foundry. The controlled values of different casting parameters such as pouring temperature, inoculation, carbon equivalent, moisture content, green compression strength, permeability and mould hardness were selected. Three different melts of metal with 0.4wt.%, 0.6wt.%, and 0.8wt.% inoculation （Fe-Si-Mg alloy and post inoculant） were produced using a 1-ton capacity coreless medium frequency induction furnace. L-27 orthogonal array with 3-level settings were chosen for the analysis. Responses for each run were observed. The signal-to-noise （S/N） ratio for each run was calculated using the Taguchi approach, and the optimized levels of different casting parameters were identified based on the SIN ratio. The analysis of variance for the casting acceptance percentage concludes that inoculation is the most significant factor affecting the castings＇ quality with a contribution percentage of 44%; an increase in inoculation results in a significant improvement in acceptance percentage of ductile iron castings. The experiment results showed that with the optimized parameters, the rejection rate was reduced from 16.98% to 6.07%.
基金This work is supported by the National Key R&D Program of China(2017 YFB0304200)the National Natural Science Foundation of China(51734004).
文摘The Taguchi and analysis of variance (ANOVA) methods were applied to investigate the effects of the structural and operational parameters on the heat transfer performance of a vertical sinter cooling packed bed. The analysed parameters were the gas flow rate, the air inlet temperature, the sinter inlet temperature, the cooling bed diameter and the cooling bed height, all of which contain three levels. The purpose was to improve the heat transfer performance of a vertical sinter cooling bed. A numerical analysis model was established to assess the heat transfer performance with respect to the varying parameters and their different levels. This mathematical model was validated by using data from practical industrial processes. The Taguchi method for the L27 (35) orthogonal design experiment was selected to evaluate the impacts of the design parameters on the heat transfer performance and to acquire the optimum combination of parameters. The analysis of variance was applied to assess the impact weights and the order of significance of the design parameters. The results show that the sinter inlet temperature and cooling bed diameter have great influences and impact the exergy of the wasted heat recovery by 61.65% and 23.31%, respectively. However, the gas flow rate and the air inlet temperature have small effects on the response. Furthermore, the air and sinter inlet temperatures have the most significant impacts on the efficiency of heat transfer by 68.83% and 23.31%, respectively. The optimal parameter combination (A1B1C3D3E3) was obtained, and the optimal results were validated by confirmation tests.
文摘Mechanical properties of semi-solid casting are dependent on multiple processing parameters,and improper processing parameters will not only reduce mean data but also increase variations.The present study investigated the impact of parameters in slurry preparation and heat treatment on the yield strength and ductility of T6 heat-treated A356 Al-Si alloy using rapid slurry forming(RSF)semi-solid casting.The focus was primarily on the robustness of mechanical properties based on Taguchi design method.By analyzing signal-to-noise ratio and minimum value calculated from-3S,the optimum slurry preparation parameters and heat treatment parameters were determined to be no quench,enthalpy exchange material(EEM)temperature of 140℃,EEM-to-melt ratio of 6mass%,stirring time of 18 s,solution heat treated at 520℃ for 2 h,and ageing heat treated at 190℃ for 6 h.In a small batch validation,the-3S yield strength and-3S elongation reach 256.1 MPa and 5.03% respectively,showing a satisfactory robustness.The hardness and microstructure of heat-treated samples with the best and worst properties were characterized to gain insight into the underlying mechanisms affecting the mean value and variations of mechanical properties.
基金supported in part by the“Chunhui Plan”Collaborative Research Project of Chinese Ministry of Education under Grant HZKY20220604by the National Natural Science Foundation of China under Grant 52107007。
文摘With the continuous improvement of permanent magnet(PM)wind generators'capacity and power density,the design of reasonable and efficient cooling structures has become a focus.This paper proposes a fully enclosed self-circulating hydrogen cooling structure for a originally forced-air-cooled direct-drive PM wind generator.The proposed hydrogen cooling system uses the rotor panel supports that hold the rotor core as the radial blades,and the hydrogen flow is driven by the rotating plates to flow through the axial and radial vents to realize the efficient cooling of the generator.According to the structural parameters of the cooling system,the Taguchi method is used to decouple the structural variables.The influence of the size of each cooling structure on the heat dissipation characteristic is analyzed,and the appropriate cooling structure scheme is determined.
文摘Environmental issues like pollution are major threats to human health.Many systems are developed to reduce pollution.In this paper,an optimal mobile robot design to reduce pollution in Green supply chain management system.Green supply chain management involves as similating environmentally and eco-nomically feasible solutions into the supply chain life-cycle.Smartness,advanced technologies,and advanced networks are becoming pillars of a sustainable supply chain management system.At the same time,there is much change happening in the logistics industry.They are moving towards a new logistics model.In the new model,robotic logistics has a vital role.The reasons for this change are the rapid growth of the e-commerce business and the shortage of workers.The advantages of using robotic logistics are reduction in human errors,faster delivery speed,better customer satisfaction,more safety for workers,and high workforce adaptability.A robot with rocker-bogie suspension is a six-wheeled mobile platform that has a distinctive potential to keep all wheels on the ground continuously.It has been designed to traverse rough and uneven terrain by distributing the load over its wheels equally.However,there is a limitation to achieving high-speed mobility against vertical barriers.In this research,an optimal design of product delivery wheeled robots for a sustainable supply chain system is proposed to ensure higher adaptability and maximum stability during climbing staircases.The design parameters of the proposed robot are optimized using Taguchi Method.The aim is to get a smooth trajectory of the robot’s center-of-mass.The proposed approach realizes a robot with much-improved stability which can climb over heights more than the size of the wheel(i.e.,3 times the radius of wheels).The results reveal that the modified rocker-bogie system not only increases the stair-climbing capability but also thwarts instability due to overturning of a wheel of the robot.
基金supported by the National Natural Science Funds of China No.51907129Technology program of Liaoning province No.2021-MS-236。
文摘In this paper,a 20kW vehicle built-in permanent magnet synchronous motor is taken as an example,and a magnetic barrier structure is added to the rotor of the motor to solve the uneven saturation problem of the rotor side magnetic bridge.This structure improves the air-gap flux density waveform of the motor by influencing the internal magnetic flux path of the motor rotor,thus improving the sine of the no-load back EMF waveform of the motor and reducing the torque ripple of the motor.At the same time,Taguchi method is used to optimize the structural parameters of the added magnetic barrier.In order to facilitate the analysis of its uneven saturation phenomenon and improve the optimization effect,a simple equivalent magnetic network(EMN)model considering the uneven saturation of rotor magnetic bridge is established in this paper,and the initial values of optimization factors are selected based on this model.Finally,the no-load back EMF waveform distortion rate,torque ripple and output torque of the optimized motor are compared and analyzed,and the influence of magnetic barrier structure parameters on the electromagnetic performance of the motor is also analyzed.The results show that the optimized motor can not change the output torque of the motor as much as possible on the basis of reducing the waveform distortion rate of no-load back EMF and torque ripple.
文摘The application of new soft magnetic materials in permanent magnet motor can effectively reduce the loss of motor and improve the efficiency of motor. Taguchi method is a local multivariable and multi-objective optimization method widely used in various engineering problems, which can effectively improve the efficiency of engineering optimization. In this paper, based on a 25 kW, 1700 r/min three-phase permanent magnet motor, the relevant motor model is established in the finite element simulation software, and the relevant simulation analysis is carried out. Combined with Taguchi method optimization, the local optimal structure scheme is obtained. Through optimization, the motor can maintain high efficiency, reduce the cogging torque of the motor by 53.45%, reduce the torque ripple by 36.79%, and increase the torque generated by the permanent magnet per unit mass by 21.42%. Through this optimization, the overall performance of the motor has been significantly improved. The research content of this paper verifies the feasibility of the application of Taguchi method in the optimization of new soft magnetic material motor, provides a new idea for the optimization design of new soft magnetic material motor, and also provides a certain reference for the local multi-objective optimization of the electromagnetic structure of other similar motors.
文摘Taguchi method has been employed to investigate the effects of cutting fluids on surface roughness in turning AISI 1330 alloy steel, using manually operated lathe machine. Experiments have been conducted using L<sub>27 </sub>(3<sup>4</sup>) orthogonal array and each experiment was repeated three times and each test used a new cutting tool, High Speed Steel (HSS), to ensure accurate readings of the surface roughness. The statistical methods of Signal-to-Noise (S/N) ratio and the Analysis of Variance (ANOVA) were applied to investigate effects of cutting speed, feed rate and depth of cut on surface roughness under different cutting fluids. Minitab 14 software was used to analyze the effect of variables on the surface roughness. Results obtained indicated that optimal variables for the minimum surface roughness were cutting speed of 35 m/min (level 2), feed of 0.124 mm/rev (level 1), depth of cut of 0.3 mm (level 1) and a cutting fluid with a viscosity of 2.898 mm<sup>2</sup>/s (level 3). Hence, the optimal parameters to obtain better surface roughness of the workpiece material were obtained when groundnut oil based cutting fluid was used. Analysis of variance shows that feed rate has the most significant effect on surface roughness.
文摘Understanding the complex interaction between heat and mass transfer in non-Newtonian microflows is essential for the development and optimization of efficient microfluidic and thermal management systems.This study investigates the magnetohydrodynamic(MHD)thermosolutal convection of a Casson fluid within an inclined,porous microchannel subjected to convective boundary conditions.The nonlinear,coupled equations governing momentum,energy,and species transport are solved numerically using the MATLAB bvp4c solver,ensuring high numerical accuracy and stability.To identify the dominant parameters influencing flow behavior and to optimize transport performance,a comprehensive hybrid optimization framework—combining a modified Taguchi design,Grey Relational Analysis(GRA),and Principal Component Analysis(PCA)—is proposed.This integrated strategy enables the simultaneous assessment of skin friction,Nusselt number,and Sherwood number,providing a rigorous multi-objective evaluation of system performance.Comparative validation with benchmark results from the literature confirms the accuracy and reliability of the present formulation and its numerical implementation.The results highlight the intricate coupling among flow slip,buoyancy effects,and convective transport mechanisms.Increased slip flow enhances axial velocity,while a higher solutal Biot number intensifies concentration gradients near the channel walls.Conversely,a lower thermal Biot number diminishes the temperature field,indicating weaker heat transfer across the boundaries.PCA results reveal that the first principal component(PC1)accounts for most of the system variance,demonstrating the dominant influence of coupled flow and transport parameters on overall system performance.
