Water-soluble crude polyseccharide（PIP） was extracted from cultured mycelium of the fungus Phellinus igniarius. After ethanol precipitation and sepharose CL-6B gel filtration, the fraction of PIP1 was obtained, whic...Water-soluble crude polyseccharide（PIP） was extracted from cultured mycelium of the fungus Phellinus igniarius. After ethanol precipitation and sepharose CL-6B gel filtration, the fraction of PIP1 was obtained, which was shown to be a homogeneous polysaccharide by means of high-performance liquid chromatography. The structure of PIPt was determined by using several methods. C.,C analysis indicates that PIP1 is composed of the monosaccharides of glucose, galactose, and mannose. Their malar ratio is 3. 70： 4. 06： 1.00. The molar weight was estimated to be 17 kd via HPLC. IR, GC, partial hydrolysis with acid, pefiedate oxidation, Smith degradation, methylation, and GC-MS analysis were used for the structural analyses of PIP1. The results show that PIP1 has a small quantity of branch structure, The main glycosidic linkage of PIP1 has a β-configurafion. The main chain is made up of a large mass of glucose （ 1→3 ） and few mannose （ 1→4 ） ; the side chain is composed of glucose （ 1 →3 ） and galactose （ 1→6 ） ; the nonreduced end is composed of galactose and glucose. The side chains are branched at 6-0 of glucose（ 1→3,6） and mannose（1→4,6）. On an average, there are three branches among 20 residues. It is presumable that the existence of 1,3-linked Glc in the main and side chains is the main reason for its higher antitumor activity.展开更多
The North Qilian Shan fold and thrust belt,located at the northern Tibetan Plateau and southern margin of the Hexi Corridor,is a key tectonic unit to decode the formation and expansion of the plateau.Previous studies ...The North Qilian Shan fold and thrust belt,located at the northern Tibetan Plateau and southern margin of the Hexi Corridor,is a key tectonic unit to decode the formation and expansion of the plateau.Previous studies emphasize the Cenozoic deformation due to the far-field response to the Indo-Asian collision,but the Mesozoic deformations are poorly constrained in this area.We conducted detailed field mapping,structural analysis,geochronology,and structural interpretation of deep seismic reflectional profiling and magnetotelluric(MT)sounding,to address the superposed results of the Mesozoic and Cenozoic deformation.The results recognized the North Qilian thrust and nappe system(NQTS),the root and the frontal belt are the North Qilian thrust(NQT),and the Yumu Shan klippe(YK),respectively.The middle belt is located between the NQT and the YK.Monzonitic granite zircon U-Pb dating from the middle belt yields an age of ca.415 Ma,which is similar to south NQT.The thrusting displacement is estimated at ca.48 km by structural interpretation of deep profiles.The timing is constrained in the early stage of the Early Cretaceous by the formation of simultaneous growth strata.We suggest that the NQTS has resulted from the far-field effect of the Lhasa-Qiangtang collision,and the Yumu Shan is uplifted by the superposed Cenozoic deformation.展开更多
Compressional region usually forms complex thrust faults system, which is difficult to identify using traditional migration profiles. The successful application of three-dimensional（3D） seismic attributes analysis g...Compressional region usually forms complex thrust faults system, which is difficult to identify using traditional migration profiles. The successful application of three-dimensional（3D） seismic attributes analysis greatly reduces the difficulty, and improves the accuracy and efficiency of seismic interpretation and structural analysis. In this paper, we took Qiongxi area in the compressional region of western Sichuan as an example, using two 3D seismic attributes, coherence and instantaneous phase, to identify fault assemblages and variations both vertically and laterally. The results show that the study area mainly consists of NS-, NE- and NEE-trending faults. The NS-trending faults are the largest and have a component of sinistral slip controlling the formation of NEE-trending faults, while the NE-trending faults are intermediate in scale, formed earlier and were cut by the NS-trending faults. Our results demonstrate that using seismic attributes for structural analysis have the following advantages：（1） more details of major fault zones,（2） highlighting minor faults which are hardly traced in seismic migration cube, and（3） easier acquisition of accurate fault systems. The application of seismic attributes provides a new idea for deciphering fine and complicated structures, and will significantly contribute to the development of objective and precise geological interpretation in the future.展开更多
A better understanding of the relationship between the structure and functions of urban and suburban spaces is one of the avenues of research still open for geographical information science.The research presented in t...A better understanding of the relationship between the structure and functions of urban and suburban spaces is one of the avenues of research still open for geographical information science.The research presented in this paper develops several graph-based metrics whose objective is to characterize some local and global structural properties that reflect the way the overall building layout can be cross-related to the one of the road layout.Such structural properties are modeled as an aggregation of parcels,buildings,and road networks.We introduce several computational measures(Ratio Minimum Distance,Minimum Ratio Minimum Distance,and Metric Compactness)that respectively evaluate the capability for a given road to be connected with the whole road network.These measures reveal emerging sub-network structures and point out differences between less-connective and moreconnective parts of the network.Based on these local and global properties derived from the topological and graph-based representation,and on building density metrics,this paper proposes an analysis of road and building layouts at different levels of granularity.The metrics developed are applied to a case study in which the derived properties reveal coherent as well as incoherent neighborhoods that illustrate the potential of the approach and the way buildings and roads can be relatively connected in a given urban environment.Overall,and by integrating the parcels and buildings layouts,this approach complements other previous and related works that mainly retain the configurational structure of the urban network as well as morphological studies whose focus is generally limited to the analysis of the building layout.展开更多
Proteomics is the study of proteins and their interactions in a cell. With the successful completion of the Human Cenome Project, it comes the postgenome era when the proteomics technology is emerging. This paper stud...Proteomics is the study of proteins and their interactions in a cell. With the successful completion of the Human Cenome Project, it comes the postgenome era when the proteomics technology is emerging. This paper studies protein molecule from the algebraic point of view. The algebraic system （∑, ＋, ＊） is introduced, where ∑ is the set of 64 codons. According to the characteristics of （∑, ＋, ＊）, a novel quasi-amino acids code classification method is introduced and the corresponding algebraic operation table over the set ZU of the 16 kinds of quasi-amino acids is established. The internal relation is revealed about quasi-amino acids. The results show that there exist some very close correlations between the properties of the quasi-amino acids and the codon. All these correlation relationships may play an important part in establishing the logic relationship between codons and the quasi-amino acids during the course of life origination. According to Ma F et al （2003 J. Anhui Agricultural University 30 439）, the corresponding relation and the excellent properties about amino acids code are very difficult to observe. The present paper shows that （ZU, ＋,×） is a field. Furthermore, the operational results display that the eodon tga has different property from other stop codons. In fact, in the mitochondrion from human and ox genomic codon, tga is just tryptophane, is not the stop codon like in other genetic code, it is the case of the Chen W C et al （2002 Acta Biophysiea Siniea 18（1） 87）. The present theory avoids some inexplicable events of the 20 kinds of amino acids code, in other words it solves the problem of ＇the 64 codon assignments of mRNA to amino acids is probably completely wrong＇ proposed by Yang （2006 Progress in Modern Biomedicine 6 3）.展开更多
In this paper,three different modeling ranges were selected in the structural analysis for a hydropower house.The analysis was carried out using ABAQUS 6.6.The modeling range has a remarkable effect on finite element ...In this paper,three different modeling ranges were selected in the structural analysis for a hydropower house.The analysis was carried out using ABAQUS 6.6.The modeling range has a remarkable effect on finite element method(FEM) calculation result at the middle position of typical cross-sections where the concrete is relatively thin,and at the region close to turbine floor.If the ventilation barrel,floor slabs and columns above turbine floor are excluded from FEM model,the maximum rise difference of pedestal structure increases by about 24% compared with that of the whole model.It is indicated that different modeling ranges indeed affect FEM calculation result,and the structure above turbine floor in the FEM model should be included.展开更多
According to the technical characteristics of short fixed wheelbase of a high-speed carriage, a subgrade-track integrated space mechanical response analysis model is proposed for trains under the action ofbiaxial load...According to the technical characteristics of short fixed wheelbase of a high-speed carriage, a subgrade-track integrated space mechanical response analysis model is proposed for trains under the action ofbiaxial load after the comparison of the stress distribution characteristics of the ballast track subgrade bed structures for high-speed railway under the action of uniaxial load and biaxial load. The loading threshold value （high-cycle long-term dynamic strength） under the circum- stance where the cumulative deformation of subgrade structure gradually develops and finally reaches the convergent state, and its relationship with the foundation coefficient K30 were deduced, based on the characteristics of cumulative defor- mation evolution obtained from the unit structure filling model test under the action of cyclic loading. In view of structure stability and frost resistance requirements of the railway subgrade in cold regions, technical conditions to maintain good service performance of subgrade structure of high-speed railway ballasted track are discussed and analyzed. Study results show that the additive effect manifests itself obviously for railway train bogies under the action of biaxial load than uni- axial load, which has a significant dynamic effect on the subgrade bed bottom and a slight effect on the surface layer. Thus, the adoption of a biaxial load model in the design of a high-speed railway subgrade accurately reflects the vehicle load. Pursuant to the structure design principle, the design method of the subgrade structure of high-speed railway ballasted track is proposed to meet the technical requirements such as structural strength, bearing stiffness and high-cyclic and long-term stability. Technical indicators are obtained for the variation of thickness of the surface layer of reinforced sub- grade bed in the double-layer subgrade mode along with the change of K30 at the subgrade bed bottom. The double-layer structure mode of ＂closure on the upper layer and drainage on the lower layer＂ was proposed in order to meet the water- proofing and drainage requirements of the upper layer of the subgrade bed in cold regions. A dense-framework graded gravel filler with weak water permeability at a coefficient of 10 4 cm/s is used on the upper layer and the void-framework graded gravel filler at the water permeability coefficient of 10 2 cm/s is adopted on the lower layer.展开更多
Structures and crystal form transition of the novel aryl ether ketone polymer containing meta-phenylene linkage: PEKEKK(T/I) were investigated by wide angle X-ray diffraction (WAXD), imaging plates (IPs) and small ang...Structures and crystal form transition of the novel aryl ether ketone polymer containing meta-phenylene linkage: PEKEKK(T/I) were investigated by wide angle X-ray diffraction (WAXD), imaging plates (IPs) and small angle X-ray scattering (SAXS). The energy of activation of the decomposition reaction and degree of crystallinity of PEKEKK(T/I) were determined by WAXD and thermo-gravimetric analysis (TGA), respectively. Results obtained from WAXD and IPs show that crystal forms coexist in the PEKEKK(T/I) samples isothermally cold crystallized in the temperature range from 180'C to 240T? and only form occurs in PEKEKK(TTI) samples isothermally cold crystallized at 2701C. The radius of gyration (Rg), thickness of microregions with electron-density fluctuations (E) and distribution of particle sizes were investigated by SAXS.展开更多
A modified space beam element is presented in this paper to consider the local joint flexibility of T, Y tubular joints subjected to axial forces and in-plane bending moments for analysis of platforms. Two numerical e...A modified space beam element is presented in this paper to consider the local joint flexibility of T, Y tubular joints subjected to axial forces and in-plane bending moments for analysis of platforms. Two numerical examples are shown to verify the efficiency and validity of the method presented here.展开更多
The cubic sodium tungsten bronzes, Na_xWO_3(x=0.854 and 0.814)were prepared by rare earths gaseous permeation method. Structural analysis was carried out by Rietveld method from powder X-ray diffraction data. The X-ra...The cubic sodium tungsten bronzes, Na_xWO_3(x=0.854 and 0.814)were prepared by rare earths gaseous permeation method. Structural analysis was carried out by Rietveld method from powder X-ray diffraction data. The X-ray diffraction profile calculated with cubic P32 models are in good agreement with the observed X-ray diffraction patterns. There is only a little difference in W-O bond and Na-O bond between Na_(0.854)WO_3 and Na_(0.814)WO_3. Conductivity measurements indicate that Na_xWO_3 show anomalous semiconducting behavior and percolation model was used to interpret it.展开更多
Electrochemical polymerization of 3-fluoroalkoxy and 3-fluoroether thiophenes gives polymers with relatively high molecular weights and good processibility. Investigation of these polymers by means of GPC indicates th...Electrochemical polymerization of 3-fluoroalkoxy and 3-fluoroether thiophenes gives polymers with relatively high molecular weights and good processibility. Investigation of these polymers by means of GPC indicates that an increase in the number of fluorine atoms in the fluorinated group results in a decrease in degree of polymerization of the polymers in the same polythiophene series. As shown by NMR and FTIR, the polyfluorinated group substituted polythiophenes have regular 2, 5-coupling in their main chains. The SEM micrographs of the polymer films exhibit that polymer (1)-poly [3-2, 2, 3, 3-tetrafluoro-propoxy) thiophene] possesses more regular structure than the other polymers do. Substitution of polythiophenes by fluorinated groups leads to the polymers with high electric, electrochemical and thermal stability.展开更多
Eu 2Mn 2/3Ta 4/3O 7 specimen was synthesized from Eu 2O 3, MnO and Ta 2O 5 in a reducing atmosphere. Structure analysis was carried out by Rietveld method from X-ray diffraction data. The X-ray diffraction...Eu 2Mn 2/3Ta 4/3O 7 specimen was synthesized from Eu 2O 3, MnO and Ta 2O 5 in a reducing atmosphere. Structure analysis was carried out by Rietveld method from X-ray diffraction data. The X-ray diffraction profile calculated with monoclinic C2/c model was in a good agreement with the observed X-ray diffraction patterns since several small peaks of super lattice could be also assigned with C2/c symmetry in addition to fundamental reflection peaks. Eu 2Mn 2/3Ta 4/3O 7 has two kinds of distorted (Mn, Ta)O 6 octahedra and HTB layers, which deviates from the regular forms. Europium atoms coordinate to eight or seven oxygen atoms and lead to two kinds of polyhedra, EuO 8 and EuO 7 in this compound.展开更多
The re-design of the adoptable structure and the cooling manner of the divertor in the HL-2A tokamak is based on the parameters confirmed by the optimum divertor configuration and the primary modification scheme. The ...The re-design of the adoptable structure and the cooling manner of the divertor in the HL-2A tokamak is based on the parameters confirmed by the optimum divertor configuration and the primary modification scheme. The characteristics of the new divertor system include the double shear joint design on the domes and the outer target plates as well as the poloidal flow with toroidal manifolds. The results of the thermal and structural analysis of the outer target plates show that the design of the poloidal flow with toroidal manifolds can improve the capability of the target plates to withstand the heat loads, and the double shear joint design is compatible with the stress intensity requirements by the electromagnetic loads due to halo currents.展开更多
WAXD and SAXS for PA1010+BMI system have been measured. The results obtained with the help of Ruland and ID EDCF. showed that Wc1x1, the long period L and the thickness of the crystal lamellae do decreased with BMI co...WAXD and SAXS for PA1010+BMI system have been measured. The results obtained with the help of Ruland and ID EDCF. showed that Wc1x1, the long period L and the thickness of the crystal lamellae do decreased with BMI content at PA10101+BMI system. Comparing both experimental and calculated densitl c values indicated thst the values were of better conformity. Adding BHI into PA1010 caused an increase in distortion.The results from SAXS analysis have also led to the conclusion that a crystal-amorphous interphase could exist in lamellae of Semicrystalline polymers and a three-phase model instead of traditional two-phase model should be used.展开更多
A series of ternary lanthanide complexes Ln （C6H5CHOHCOO）3（phen） （H2O） （Ln= La, Ce, Pr, Nd, Sm, Eu） were synthesized with α-hydroxyl-phenyl-acetic acid and 1, 10-phenanthroline （phen） as ligands. The sturct...A series of ternary lanthanide complexes Ln （C6H5CHOHCOO）3（phen） （H2O） （Ln= La, Ce, Pr, Nd, Sm, Eu） were synthesized with α-hydroxyl-phenyl-acetic acid and 1, 10-phenanthroline （phen） as ligands. The sturcture and property of complexes were characterized by elemental analysis, IR, 1^H-NMR, UV and TGA, and the coordinate mede of both ligands was discussed. It was shown that the co-ordinate mode of 1, 10-phenanthroline was chelated, while α-hydraxyl-phenyl-acetate ion was monedentate or bridging. The mechanism of thermal determinde by thermogravimetry was indicated that the degree of co-ordinate ability of ligand was： α-hydroxyl-phenyl-acetate ion 〉 1, 10- phenanthroline（phen）.展开更多
The central solenoid (CS) composed of cable-in-conduit (CIC) type conductor is animportant part of the HT-7U device. The CS coils can be considered from the viewpoint of micro-mechanics as a composite material. And th...The central solenoid (CS) composed of cable-in-conduit (CIC) type conductor is animportant part of the HT-7U device. The CS coils can be considered from the viewpoint of micro-mechanics as a composite material. And then, the residual stiffness is computed according to themicro-damage modeling of continuum damage mechanics. These material properties have beenused as input data for finite element method (FEM) analysis. In this paper the computationalanaysis of the stress and the displacement on the central solenoid are made by the finite elementanalysis system COSMOS/M2.0 under Operating temperature. According to the analytical results,the CS coils are all satisfied with designed safety criteria.展开更多
A surface spline function is used to fit a coal seam surface in structural anal ysis in coal geology. From the surface spline function, the first and second partial derivatives can also be derived and used to structur...A surface spline function is used to fit a coal seam surface in structural anal ysis in coal geology. From the surface spline function, the first and second partial derivatives can also be derived and used to structural analysis, especially for recogni tion of the concealed structures. The detection of structures related to faulting is em phasized.展开更多
Purpose of present work is to develop a reliable and simple method for structural analysis of RC Shear Walls. The shear wall is simulated by a truss model as the bar of a truss is the simplest finite element. An itera...Purpose of present work is to develop a reliable and simple method for structural analysis of RC Shear Walls. The shear wall is simulated by a truss model as the bar of a truss is the simplest finite element. An iterative method is used. Initially, there are only concrete bars. Repeated structural analyses are performed. After each structural analysis, every concrete bar exceeding tensile strength is replaced by a steel bar. For every concrete bar exceeding compressive strength, first its section area is increased. If this is not enough, a steel bar is placed at the side of it. For every steel bar exceeding tensile or compressive strength, its section area is increased. After the end of every structural analysis, if all concrete and steel bars fall within tensile and compressive strengths, the output data are written and the analysis is terminated. Otherwise, the structural analysis is repeated. As all the necessary conditions (static, elastic, linearized geometric) are satisfied and the stresses of ALL concrete and steel bars fall within the tensile and compressive strengths, the results are acceptable. Usually, the proposed method exhibits a fast convergence in 4 - 5 repeats of structural analysis of the RC Shear Wall.展开更多
Loads on a gearbox casing of a certain type of tracked vehicle were calculated according to the engine＇s full load characteristic curve and the worst load condition where the gearbox operated while the tracked vehicl...Loads on a gearbox casing of a certain type of tracked vehicle were calculated according to the engine＇s full load characteristic curve and the worst load condition where the gearbox operated while the tracked vehicle was running, and then stiffness and strength of the casing were analyzed by means of Patran/Nastran software. After a- nalysis, it was found that the casing satisfied the Mises ＇ yield condition; however, the stress distribution was hetero- geneous, and stresses near the bearing saddle bores of the casing were higher while those in other regions were much less than the allowable stress. For this reason, thicknesses of the casing wall on bearing assembling holes needed in- creasing, while those in other places can decrease. After much structural improving and re-analysis, the optimal casing design was found, and its weight decreased by 5% ; the casing still satisfied the Mises yield criterion and the stress distribution was more homogeneous.展开更多
Thirteen fractions from the pathogenic plant fungus Setosphaeria turcica race 1 were separated and collected using high performance liquid chromatography （HPLC）. Their toxic activities were assayed through leaf punc...Thirteen fractions from the pathogenic plant fungus Setosphaeria turcica race 1 were separated and collected using high performance liquid chromatography （HPLC）. Their toxic activities were assayed through leaf puncturing on corn differentials （OH43, OH43Ht1, OH43Ht2, and OH43HtN）, and the results revealed that eight fractions were toxic and fraction 6 was specifically toxic to OH43Ht1, which could be taken as a gene-selective toxin fraction. Fraction 6 was finely purified via HPLC and condensed by freeze desiccation. Its chemical structure was analyzed with EI-MS, IR, HMBC, ^1H-NMR, and two-dimensional NMR. The results suggested that fraction 6 contained an unsaturated double bond, carbonyl and methylene groups with molecular weight of 142.展开更多
基金Supported by the Science and Technique Bureau of Wenzhou City(No. S2005A003).
文摘Water-soluble crude polyseccharide（PIP） was extracted from cultured mycelium of the fungus Phellinus igniarius. After ethanol precipitation and sepharose CL-6B gel filtration, the fraction of PIP1 was obtained, which was shown to be a homogeneous polysaccharide by means of high-performance liquid chromatography. The structure of PIPt was determined by using several methods. C.,C analysis indicates that PIP1 is composed of the monosaccharides of glucose, galactose, and mannose. Their malar ratio is 3. 70： 4. 06： 1.00. The molar weight was estimated to be 17 kd via HPLC. IR, GC, partial hydrolysis with acid, pefiedate oxidation, Smith degradation, methylation, and GC-MS analysis were used for the structural analyses of PIP1. The results show that PIP1 has a small quantity of branch structure, The main glycosidic linkage of PIP1 has a β-configurafion. The main chain is made up of a large mass of glucose （ 1→3 ） and few mannose （ 1→4 ） ; the side chain is composed of glucose （ 1 →3 ） and galactose （ 1→6 ） ; the nonreduced end is composed of galactose and glucose. The side chains are branched at 6-0 of glucose（ 1→3,6） and mannose（1→4,6）. On an average, there are three branches among 20 residues. It is presumable that the existence of 1,3-linked Glc in the main and side chains is the main reason for its higher antitumor activity.
基金financially supported by the China Geological Survey(Grant Nos.DD20230229,DD20160083,DD20190011,DD20221643-5)the National Key Research and Development Program of China(the DREAM—Deep Resource Exploration and Advanced Mining+1 种基金Grant No.2018YFC0603701)the Cooperative Project between the Chinese Academy of Geological Sciences and the Sinopec Shengli Oilfield Company(Grant No.P22065)。
文摘The North Qilian Shan fold and thrust belt,located at the northern Tibetan Plateau and southern margin of the Hexi Corridor,is a key tectonic unit to decode the formation and expansion of the plateau.Previous studies emphasize the Cenozoic deformation due to the far-field response to the Indo-Asian collision,but the Mesozoic deformations are poorly constrained in this area.We conducted detailed field mapping,structural analysis,geochronology,and structural interpretation of deep seismic reflectional profiling and magnetotelluric(MT)sounding,to address the superposed results of the Mesozoic and Cenozoic deformation.The results recognized the North Qilian thrust and nappe system(NQTS),the root and the frontal belt are the North Qilian thrust(NQT),and the Yumu Shan klippe(YK),respectively.The middle belt is located between the NQT and the YK.Monzonitic granite zircon U-Pb dating from the middle belt yields an age of ca.415 Ma,which is similar to south NQT.The thrusting displacement is estimated at ca.48 km by structural interpretation of deep profiles.The timing is constrained in the early stage of the Early Cretaceous by the formation of simultaneous growth strata.We suggest that the NQTS has resulted from the far-field effect of the Lhasa-Qiangtang collision,and the Yumu Shan is uplifted by the superposed Cenozoic deformation.
基金supported by the Major National S & T Program (No. 2008ZX050009-001-01)
文摘Compressional region usually forms complex thrust faults system, which is difficult to identify using traditional migration profiles. The successful application of three-dimensional（3D） seismic attributes analysis greatly reduces the difficulty, and improves the accuracy and efficiency of seismic interpretation and structural analysis. In this paper, we took Qiongxi area in the compressional region of western Sichuan as an example, using two 3D seismic attributes, coherence and instantaneous phase, to identify fault assemblages and variations both vertically and laterally. The results show that the study area mainly consists of NS-, NE- and NEE-trending faults. The NS-trending faults are the largest and have a component of sinistral slip controlling the formation of NEE-trending faults, while the NE-trending faults are intermediate in scale, formed earlier and were cut by the NS-trending faults. Our results demonstrate that using seismic attributes for structural analysis have the following advantages：（1） more details of major fault zones,（2） highlighting minor faults which are hardly traced in seismic migration cube, and（3） easier acquisition of accurate fault systems. The application of seismic attributes provides a new idea for deciphering fine and complicated structures, and will significantly contribute to the development of objective and precise geological interpretation in the future.
文摘A better understanding of the relationship between the structure and functions of urban and suburban spaces is one of the avenues of research still open for geographical information science.The research presented in this paper develops several graph-based metrics whose objective is to characterize some local and global structural properties that reflect the way the overall building layout can be cross-related to the one of the road layout.Such structural properties are modeled as an aggregation of parcels,buildings,and road networks.We introduce several computational measures(Ratio Minimum Distance,Minimum Ratio Minimum Distance,and Metric Compactness)that respectively evaluate the capability for a given road to be connected with the whole road network.These measures reveal emerging sub-network structures and point out differences between less-connective and moreconnective parts of the network.Based on these local and global properties derived from the topological and graph-based representation,and on building density metrics,this paper proposes an analysis of road and building layouts at different levels of granularity.The metrics developed are applied to a case study in which the derived properties reveal coherent as well as incoherent neighborhoods that illustrate the potential of the approach and the way buildings and roads can be relatively connected in a given urban environment.Overall,and by integrating the parcels and buildings layouts,this approach complements other previous and related works that mainly retain the configurational structure of the urban network as well as morphological studies whose focus is generally limited to the analysis of the building layout.
基金Project supported in part by the International Technology Collaboration Research Program of China (Grant No 2007DFA706700)
文摘Proteomics is the study of proteins and their interactions in a cell. With the successful completion of the Human Cenome Project, it comes the postgenome era when the proteomics technology is emerging. This paper studies protein molecule from the algebraic point of view. The algebraic system （∑, ＋, ＊） is introduced, where ∑ is the set of 64 codons. According to the characteristics of （∑, ＋, ＊）, a novel quasi-amino acids code classification method is introduced and the corresponding algebraic operation table over the set ZU of the 16 kinds of quasi-amino acids is established. The internal relation is revealed about quasi-amino acids. The results show that there exist some very close correlations between the properties of the quasi-amino acids and the codon. All these correlation relationships may play an important part in establishing the logic relationship between codons and the quasi-amino acids during the course of life origination. According to Ma F et al （2003 J. Anhui Agricultural University 30 439）, the corresponding relation and the excellent properties about amino acids code are very difficult to observe. The present paper shows that （ZU, ＋,×） is a field. Furthermore, the operational results display that the eodon tga has different property from other stop codons. In fact, in the mitochondrion from human and ox genomic codon, tga is just tryptophane, is not the stop codon like in other genetic code, it is the case of the Chen W C et al （2002 Acta Biophysiea Siniea 18（1） 87）. The present theory avoids some inexplicable events of the 20 kinds of amino acids code, in other words it solves the problem of ＇the 64 codon assignments of mRNA to amino acids is probably completely wrong＇ proposed by Yang （2006 Progress in Modern Biomedicine 6 3）.
基金Supported by National Natural Science Foundation of China(No.50539010)
文摘In this paper,three different modeling ranges were selected in the structural analysis for a hydropower house.The analysis was carried out using ABAQUS 6.6.The modeling range has a remarkable effect on finite element method(FEM) calculation result at the middle position of typical cross-sections where the concrete is relatively thin,and at the region close to turbine floor.If the ventilation barrel,floor slabs and columns above turbine floor are excluded from FEM model,the maximum rise difference of pedestal structure increases by about 24% compared with that of the whole model.It is indicated that different modeling ranges indeed affect FEM calculation result,and the structure above turbine floor in the FEM model should be included.
基金financially supported by the State Key Development Program for Basic Research of China(973 Program,Grant No.2013CB036204)
文摘According to the technical characteristics of short fixed wheelbase of a high-speed carriage, a subgrade-track integrated space mechanical response analysis model is proposed for trains under the action ofbiaxial load after the comparison of the stress distribution characteristics of the ballast track subgrade bed structures for high-speed railway under the action of uniaxial load and biaxial load. The loading threshold value （high-cycle long-term dynamic strength） under the circum- stance where the cumulative deformation of subgrade structure gradually develops and finally reaches the convergent state, and its relationship with the foundation coefficient K30 were deduced, based on the characteristics of cumulative defor- mation evolution obtained from the unit structure filling model test under the action of cyclic loading. In view of structure stability and frost resistance requirements of the railway subgrade in cold regions, technical conditions to maintain good service performance of subgrade structure of high-speed railway ballasted track are discussed and analyzed. Study results show that the additive effect manifests itself obviously for railway train bogies under the action of biaxial load than uni- axial load, which has a significant dynamic effect on the subgrade bed bottom and a slight effect on the surface layer. Thus, the adoption of a biaxial load model in the design of a high-speed railway subgrade accurately reflects the vehicle load. Pursuant to the structure design principle, the design method of the subgrade structure of high-speed railway ballasted track is proposed to meet the technical requirements such as structural strength, bearing stiffness and high-cyclic and long-term stability. Technical indicators are obtained for the variation of thickness of the surface layer of reinforced sub- grade bed in the double-layer subgrade mode along with the change of K30 at the subgrade bed bottom. The double-layer structure mode of ＂closure on the upper layer and drainage on the lower layer＂ was proposed in order to meet the water- proofing and drainage requirements of the upper layer of the subgrade bed in cold regions. A dense-framework graded gravel filler with weak water permeability at a coefficient of 10 4 cm/s is used on the upper layer and the void-framework graded gravel filler at the water permeability coefficient of 10 2 cm/s is adopted on the lower layer.
基金This work was supported by the National Natural Science Foundation of China (No. 270274049) and subsidized by theSpecial Funds for Major State Basic Research Projects (G1999064800).
文摘Structures and crystal form transition of the novel aryl ether ketone polymer containing meta-phenylene linkage: PEKEKK(T/I) were investigated by wide angle X-ray diffraction (WAXD), imaging plates (IPs) and small angle X-ray scattering (SAXS). The energy of activation of the decomposition reaction and degree of crystallinity of PEKEKK(T/I) were determined by WAXD and thermo-gravimetric analysis (TGA), respectively. Results obtained from WAXD and IPs show that crystal forms coexist in the PEKEKK(T/I) samples isothermally cold crystallized in the temperature range from 180'C to 240T? and only form occurs in PEKEKK(TTI) samples isothermally cold crystallized at 2701C. The radius of gyration (Rg), thickness of microregions with electron-density fluctuations (E) and distribution of particle sizes were investigated by SAXS.
文摘A modified space beam element is presented in this paper to consider the local joint flexibility of T, Y tubular joints subjected to axial forces and in-plane bending moments for analysis of platforms. Two numerical examples are shown to verify the efficiency and validity of the method presented here.
文摘The cubic sodium tungsten bronzes, Na_xWO_3(x=0.854 and 0.814)were prepared by rare earths gaseous permeation method. Structural analysis was carried out by Rietveld method from powder X-ray diffraction data. The X-ray diffraction profile calculated with cubic P32 models are in good agreement with the observed X-ray diffraction patterns. There is only a little difference in W-O bond and Na-O bond between Na_(0.854)WO_3 and Na_(0.814)WO_3. Conductivity measurements indicate that Na_xWO_3 show anomalous semiconducting behavior and percolation model was used to interpret it.
基金This work was supported by the National Natural Science Foundation of China.
文摘Electrochemical polymerization of 3-fluoroalkoxy and 3-fluoroether thiophenes gives polymers with relatively high molecular weights and good processibility. Investigation of these polymers by means of GPC indicates that an increase in the number of fluorine atoms in the fluorinated group results in a decrease in degree of polymerization of the polymers in the same polythiophene series. As shown by NMR and FTIR, the polyfluorinated group substituted polythiophenes have regular 2, 5-coupling in their main chains. The SEM micrographs of the polymer films exhibit that polymer (1)-poly [3-2, 2, 3, 3-tetrafluoro-propoxy) thiophene] possesses more regular structure than the other polymers do. Substitution of polythiophenes by fluorinated groups leads to the polymers with high electric, electrochemical and thermal stability.
文摘Eu 2Mn 2/3Ta 4/3O 7 specimen was synthesized from Eu 2O 3, MnO and Ta 2O 5 in a reducing atmosphere. Structure analysis was carried out by Rietveld method from X-ray diffraction data. The X-ray diffraction profile calculated with monoclinic C2/c model was in a good agreement with the observed X-ray diffraction patterns since several small peaks of super lattice could be also assigned with C2/c symmetry in addition to fundamental reflection peaks. Eu 2Mn 2/3Ta 4/3O 7 has two kinds of distorted (Mn, Ta)O 6 octahedra and HTB layers, which deviates from the regular forms. Europium atoms coordinate to eight or seven oxygen atoms and lead to two kinds of polyhedra, EuO 8 and EuO 7 in this compound.
文摘The re-design of the adoptable structure and the cooling manner of the divertor in the HL-2A tokamak is based on the parameters confirmed by the optimum divertor configuration and the primary modification scheme. The characteristics of the new divertor system include the double shear joint design on the domes and the outer target plates as well as the poloidal flow with toroidal manifolds. The results of the thermal and structural analysis of the outer target plates show that the design of the poloidal flow with toroidal manifolds can improve the capability of the target plates to withstand the heat loads, and the double shear joint design is compatible with the stress intensity requirements by the electromagnetic loads due to halo currents.
文摘WAXD and SAXS for PA1010+BMI system have been measured. The results obtained with the help of Ruland and ID EDCF. showed that Wc1x1, the long period L and the thickness of the crystal lamellae do decreased with BMI content at PA10101+BMI system. Comparing both experimental and calculated densitl c values indicated thst the values were of better conformity. Adding BHI into PA1010 caused an increase in distortion.The results from SAXS analysis have also led to the conclusion that a crystal-amorphous interphase could exist in lamellae of Semicrystalline polymers and a three-phase model instead of traditional two-phase model should be used.
文摘A series of ternary lanthanide complexes Ln （C6H5CHOHCOO）3（phen） （H2O） （Ln= La, Ce, Pr, Nd, Sm, Eu） were synthesized with α-hydroxyl-phenyl-acetic acid and 1, 10-phenanthroline （phen） as ligands. The sturcture and property of complexes were characterized by elemental analysis, IR, 1^H-NMR, UV and TGA, and the coordinate mede of both ligands was discussed. It was shown that the co-ordinate mode of 1, 10-phenanthroline was chelated, while α-hydraxyl-phenyl-acetate ion was monedentate or bridging. The mechanism of thermal determinde by thermogravimetry was indicated that the degree of co-ordinate ability of ligand was： α-hydroxyl-phenyl-acetate ion 〉 1, 10- phenanthroline（phen）.
基金National Meg-Science Engineering Project of the Chinese Government.
文摘The central solenoid (CS) composed of cable-in-conduit (CIC) type conductor is animportant part of the HT-7U device. The CS coils can be considered from the viewpoint of micro-mechanics as a composite material. And then, the residual stiffness is computed according to themicro-damage modeling of continuum damage mechanics. These material properties have beenused as input data for finite element method (FEM) analysis. In this paper the computationalanaysis of the stress and the displacement on the central solenoid are made by the finite elementanalysis system COSMOS/M2.0 under Operating temperature. According to the analytical results,the CS coils are all satisfied with designed safety criteria.
文摘A surface spline function is used to fit a coal seam surface in structural anal ysis in coal geology. From the surface spline function, the first and second partial derivatives can also be derived and used to structural analysis, especially for recogni tion of the concealed structures. The detection of structures related to faulting is em phasized.
文摘Purpose of present work is to develop a reliable and simple method for structural analysis of RC Shear Walls. The shear wall is simulated by a truss model as the bar of a truss is the simplest finite element. An iterative method is used. Initially, there are only concrete bars. Repeated structural analyses are performed. After each structural analysis, every concrete bar exceeding tensile strength is replaced by a steel bar. For every concrete bar exceeding compressive strength, first its section area is increased. If this is not enough, a steel bar is placed at the side of it. For every steel bar exceeding tensile or compressive strength, its section area is increased. After the end of every structural analysis, if all concrete and steel bars fall within tensile and compressive strengths, the output data are written and the analysis is terminated. Otherwise, the structural analysis is repeated. As all the necessary conditions (static, elastic, linearized geometric) are satisfied and the stresses of ALL concrete and steel bars fall within the tensile and compressive strengths, the results are acceptable. Usually, the proposed method exhibits a fast convergence in 4 - 5 repeats of structural analysis of the RC Shear Wall.
文摘Loads on a gearbox casing of a certain type of tracked vehicle were calculated according to the engine＇s full load characteristic curve and the worst load condition where the gearbox operated while the tracked vehicle was running, and then stiffness and strength of the casing were analyzed by means of Patran/Nastran software. After a- nalysis, it was found that the casing satisfied the Mises ＇ yield condition; however, the stress distribution was hetero- geneous, and stresses near the bearing saddle bores of the casing were higher while those in other regions were much less than the allowable stress. For this reason, thicknesses of the casing wall on bearing assembling holes needed in- creasing, while those in other places can decrease. After much structural improving and re-analysis, the optimal casing design was found, and its weight decreased by 5% ; the casing still satisfied the Mises yield criterion and the stress distribution was more homogeneous.
基金supported by National Excellent Teacher's Plan,Ministry of Education,China and Natural Science Foundation of Hebei Province,China(302318).
文摘Thirteen fractions from the pathogenic plant fungus Setosphaeria turcica race 1 were separated and collected using high performance liquid chromatography （HPLC）. Their toxic activities were assayed through leaf puncturing on corn differentials （OH43, OH43Ht1, OH43Ht2, and OH43HtN）, and the results revealed that eight fractions were toxic and fraction 6 was specifically toxic to OH43Ht1, which could be taken as a gene-selective toxin fraction. Fraction 6 was finely purified via HPLC and condensed by freeze desiccation. Its chemical structure was analyzed with EI-MS, IR, HMBC, ^1H-NMR, and two-dimensional NMR. The results suggested that fraction 6 contained an unsaturated double bond, carbonyl and methylene groups with molecular weight of 142.
