Aluminum（Al） powders are used in composite explosives as a typical reducing agent for improving explosion performance. To understand energy release of aluminum in aluminized RDX-based explosives, a series of thermal...Aluminum（Al） powders are used in composite explosives as a typical reducing agent for improving explosion performance. To understand energy release of aluminum in aluminized RDX-based explosives, a series of thermal measurements and underwater explosion（UNDEX） experiments were conducted. Lithium fluoride（LiF） was added in RDX-based explosives, as a replacement of aluminum, and used in constant temperature calorimeter experiments and UNDEXs. The influence of aluminum powder on explosion heat（Qv） was measured. A rich supply of data about aluminum energy release rate was gained. There are other oxides（CO2, CO, and H2O） in detonation products besides alumina when the content of RDX is maintained at the same levels. Aluminum cannot fully combine with oxygen in the detonation products. To study the relationship between the explosive formulation and energy release, pressure and impulse signals in underwater experiments were recorded and analyzed after charges were initiated underwater. The shock wave energy（Esk）, bubble energy（Eb）, and total energy（Et） monotony increase with the Al/O ratio, while the growth rates of the shock wave energy,bubble energy, and total energy become slow.展开更多
To investigate the coupling mechanisms of detonation energy release between the TiH_(2)/PTFE active shell and RDX explosive,an RDX-based active shell thermobaric explosive containing TiH_(2)/PTFE powders was prepared....To investigate the coupling mechanisms of detonation energy release between the TiH_(2)/PTFE active shell and RDX explosive,an RDX-based active shell thermobaric explosive containing TiH_(2)/PTFE powders was prepared.The effects of the TiH_(2)/PTFE mass ratio on the shock wave parameters and afterburning effect of the thermobaric explosives were investigated.The energy release characteristics of the optimal TiH_(2)/PTFE ratio under varying vacuum degrees were evaluated using a 0.9 m3 spherical explosive chamber and colorimetric thermometry method.The experimental results demonstrated that as the PTFE powders content in the active shell increased,the shock wave intensity,explosion fireball duration,and maximum average temperature of the thermobaric explosives initially increased and then decreased,peaking at a TiH_(2)/PTFE mass ratio of 1:1.Compared to the TiH_(2)-based thermobaric explosives without PTFE,the 1:1 TiH_(2)/PTFE formulation exhibited increases of 45.9%in peak overpressure,69.7%in fireball duration,and 7.2%in maximum average temperature.Thus,an optimal PTFE content significantly enhances the energy release efficiency of the RDX/TiH_(2)/PTFE thermobaric explosives.Furthermore,the energy release efficiency of thermobaric explosives was influenced by the vacuum degree,with the maximum average temperature,peak overpressure,positive impulse,positive pressure action time,and fireball duration decreasing by 10.8%,35.3%,52.1%,65.5%,and 46.4%,respectively,as the vacuum degree increased from 0 to 52.4%.展开更多
Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al wit...Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0%to 15%,every 5%increase of aluminum resulted in about a 1.3%decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14%and 8%higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 ms throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12%and 2.9 ms higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80%of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.展开更多
While the moisture content of soil affects significantly the blast impulse of shallow buried explosives,the role of surface-covering water(SCW)on soil in such blast impulse remains elusive.A combined experimental and ...While the moisture content of soil affects significantly the blast impulse of shallow buried explosives,the role of surface-covering water(SCW)on soil in such blast impulse remains elusive.A combined experimental and numerical study has been carried out to characterize the effect of SCW on transferred impulse and loading magnitude of shallow buried explosives.Firstly,blast tests of shallow buried explosives were conducted,with and without the SCW,to quantitatively assess the blast loading impulse.Subsequently,finite element(FE)simulations were performed and validated against experimental measurement,with good agreement achieved.The validated FE model was then employed to predict the dynamic response of a fully-clamped metallic circular target,subjected to the explosive impact of shallow buried explosives with SCW,and explore the corresponding physical mechanisms.It was demonstrated that shallow buried explosives in saturated soil generate a greater impulse transferred towards the target relative to those in dry soil.The deformation displacement of the target plate is doubled.Increasing the height of SCW results in enhanced center peak deflection of the loaded target,accompanied by subsequent fall,due to the variation of deformation pattern of the loaded target from concentrated load to uniform load.Meanwhile,the presence of SCW increases the blast impulse transferred towards the target by three times.In addition,there exists a threshold value of the burial depth that maximizes the impact impulse.This threshold exhibits a strong sensitivity to SCW height,decreasing with increasing SCW height.An empirical formula for predicting threshold has been provided.Similar conclusions can be drawn for different explosive masses.The results provide technical guidance on blast loading intensity and its spatial distribution considering shallow buried explosives in coast-land battlefields,which can ultimately contribute to better protective designs.展开更多
Aromatic nitro compounds present substantial health and environmental concerns due to their toxic nature and potential explosive properties.Consequently,the development of host–vip molecular recognition systems for...Aromatic nitro compounds present substantial health and environmental concerns due to their toxic nature and potential explosive properties.Consequently,the development of host–vip molecular recognition systems for these compounds serves a dual-purpose:enabling the fabrication of high-performance sensors for detection and guiding the design of efficient adsorbents for environmental remediation.This study investigated the host–vip recognition behavior of perethylated pillar[n]arenes toward two aromatic nitro molecules,1-chloro-2,4-dinitrobenzene and picric acid.Various techniques including^(1)H NMR,2D NOESY NMR,and UV-vis spectroscopy were employed to explore the binding behavior between pillararenes and aromatic nitro vips in solution.Moreover,valuable single crystal structures were obtained to elucidate the distinct solid-state assembly behaviors of these vips with different pillararenes.The assembled solid-state supramolecular structures observed encompassed a 1:1 host–vip inclusion complex,an external binding complex,and an exo-wall tessellation complex.Furthermore,based on the findings from these systems,a pillararene-based test paper was developed for efficient picric acid detection,and the removal of picric acid from solution was also achieved using pillararenes powder.This research provides novel insights into the development of diverse host–vip systems toward hazardous compounds,offering potential applications in environmental protection and explosive detection domains.展开更多
The current work addresses the challenge of elucidating the performance of fluoroelastomers within the HMX(octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine)based polymer-bonded explosives(PBXs).To simulate the confine...The current work addresses the challenge of elucidating the performance of fluoroelastomers within the HMX(octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine)based polymer-bonded explosives(PBXs).To simulate the confined interface in PBXs,bilayer films of F2314/HMX and F2311/HMX were designed.Neutron reflectivity(NR),nanoindentation,and X-ray reflectivity(XRR)were employed to examine the layer thickness,interface characteristics,diffusion behavior,and surface morphology of the bilayers.NR measurements revealed interface thicknesses of 45Å and 98Å for F2314/HMX and F2311/HMX,respectively,indicating deeper penetration of F2311 into the HMX matrix.NR also suggested a denser polymer network with a higher scattering length density(SLD)near the HMX interface for both fluoroelastomers,while the bound layer of F2311 was notably thicker.Nanoindentation cross-checks and confirms the presence of a bound layer,highlighting the differences in stiffness and diffusion ability between the two polymers.The consistency between the NR and nanoindentation results suggests that F2311 demonstrates better flexibility and elasticity,whereas F2314 is stiffer and more plastic.Accordingly,the structures and performances of different fluoroelastomers at the HMX interface are discussed,which can provide valuable insights into the selection of binders for PBX formulations tailored to specific applications.展开更多
Detonation performance is crucial for evaluating the power of high explosives(HEs),and the equation of state(EOS)that accurately describes the high-temperature,high-pressure,and high-temperature,medium-pressure states...Detonation performance is crucial for evaluating the power of high explosives(HEs),and the equation of state(EOS)that accurately describes the high-temperature,high-pressure,and high-temperature,medium-pressure states of detonation products is key to assessing the damage efficiency of these energetic materials.This article examines the limitations of the VLW EOS in representing the thermodynamic states of explosive detonation gas products under high-temperature and medium-to high-pressure conditions.A new gas EOS for detonation products,called VHL(Virial-Han-Long),is proposed.The accuracy of VHL in describing gas states under high-temperature and medium-to high-pressure conditions is verified,and its performance in evaluating explosive detonation and working capabilities is explored.The results demonstrate that VHL exhibits high precision in calculating detonation performance.Subsequently,the detonation performance of three new HEs(ICM-101,ONC,and TNAZ)was calculated and compared to traditional HEs(TATB,CL-20,and HMX).The results indicate that ONC has superior detonation performance compared to the other explosives,while ICM-101 shows a detonation velocity similar to CL-20 but with slightly lower detonation pressure.The detonation characteristics of TNAZ are comparable to those of the standard HE HMX.From the perspective of products,considering the comprehensive work performance(mechanical work and detonation heat),both ONC and ICM-101demonstrate relatively superior performance.展开更多
Shock wave caused by a sudden release of high-energy,such as explosion and blast,usually affects a significant range of areas.The utilization of a uniform fine mesh to capture sharp shock wave and to obtain precise re...Shock wave caused by a sudden release of high-energy,such as explosion and blast,usually affects a significant range of areas.The utilization of a uniform fine mesh to capture sharp shock wave and to obtain precise results is inefficient in terms of computational resource.This is particularly evident when large-scale fluid field simulations are conducted with significant differences in computational domain size.In this work,a variable-domain-size adaptive mesh enlargement(vAME)method is developed based on the proposed adaptive mesh enlargement(AME)method for modeling multi-explosives explosion problems.The vAME method reduces the division of numerous empty areas or unnecessary computational domains by adaptively suspending enlargement operation in one or two directions,rather than in all directions as in AME method.A series of numerical tests via AME and vAME with varying nonintegral enlargement ratios and different mesh numbers are simulated to verify the efficiency and order of accuracy.An estimate of speedup ratio is analyzed for further efficiency comparison.Several large-scale near-ground explosion experiments with single/multiple explosives are performed to analyze the shock wave superposition formed by the incident wave,reflected wave,and Mach wave.Additionally,the vAME method is employed to validate the accuracy,as well as to investigate the performance of the fluid field and shock wave propagation,considering explosive quantities ranging from 1 to 5 while maintaining a constant total mass.The results show a satisfactory correlation between the overpressure versus time curves for experiments and numerical simulations.The vAME method yields a competitive efficiency,increasing the computational speed to 3.0 and approximately 120,000 times in comparison to AME and the fully fine mesh method,respectively.It indicates that the vAME method reduces the computational cost with minimal impact on the results for such large-scale high-energy release problems with significant differences in computational domain size.展开更多
Realizing effective enhancement in the thermally conductive performance of polymer bonded explosives(PBXs) is vital for improving the resultant environmental adaptabilities of the PBXs composites. Herein, a kind of pr...Realizing effective enhancement in the thermally conductive performance of polymer bonded explosives(PBXs) is vital for improving the resultant environmental adaptabilities of the PBXs composites. Herein, a kind of primary-secondary thermally conductive network was designed by water-suspension granulation, surface coating, and hot-pressing procedures in the graphene-based PBXs composites to greatly increase the thermal conductive performance of the composites. The primary network with a threedimensional structure provided the heat-conducting skeleton, while the secondary network in the polymer matrix bridged the primary network to increase the network density. The enhancement efficiency in the thermally conductive performance of the composites reached the highest value of 59.70% at a primary-secondary network ratio of 3:1. Finite element analysis confirmed the synergistic enhancement effect of the primary and secondary thermally conductive networks. This study introduces an innovative approach to designing network structures for PBX composites, significantly enhancing their thermal conductivity.展开更多
The detonation of fuel-rich explosives yields combustible products that persistently burn upon mixing with ambient oxygen,releasing additional energy through a phenomenon known as the afterburning effect.This process ...The detonation of fuel-rich explosives yields combustible products that persistently burn upon mixing with ambient oxygen,releasing additional energy through a phenomenon known as the afterburning effect.This process greatly influences the evolution of confined blast loading and the subsequent structural response,which is crucial in confined blast scenarios.Given the complex nature of the reaction process,accurate analysis of the afterburning effect remains challenging.Previous studies have either overlooked the mechanisms of detonation product combustion or failed to provide experimental validation.This study introduces a three-dimensional model to effectively characterize the combustion of detonation products.The model integrates chemical reaction source terms into the governing equations to consider the combustion processes.Numerical simulations and experimental tests were conducted to analyze the combustion and energy release from the detonation products of fuel-rich explosives in confined spaces.Approximately 50%of the energy was released during the combustion of detonation products in a confined TNT explosion.Although the combustion of these products was much slower than the detonation process,it aligned with the dynamic response of the structure,which enhanced the explosive yield.Excluding afterburning from the analysis reduced the center-point deformation of the structure by 30%.Following the inclusion of afterburning,the simulated quasistatic pressure increased by approximately 45%.Subsequent comparisons highlighted the merits of the proposed approach over conventional methods.This approach eliminates the reliance on empirical parameters,such as the amount and rate of energy release during afterburning,thereby laying the foundation for understanding load evolution in more complex environments,such as ships,buildings,and underground tunnels.展开更多
DNAN-based insensitive melt-cast explosives have been widely utilized in insensitive munition in recent years. When constrained DNAN-based melt-cast explosives are ignited under thermal stimulation, the base explosive...DNAN-based insensitive melt-cast explosives have been widely utilized in insensitive munition in recent years. When constrained DNAN-based melt-cast explosives are ignited under thermal stimulation, the base explosive exists in a molten liquid state, where high-temperature gases expand and react in the form of bubble clouds within the liquid explosive;this process is distinctly different from the dynamic crack propagation process observed in the case of solid explosives. In this study, a control model for the reaction evolution of burning-bubble clouds was established to describe the reaction process and quantify the reaction violence of DNAN-based melt-cast explosives, considering the size distribution and activation mechanism of the burning-bubble clouds. The feasibility of the model was verified through experimental results. The results revealed that under geometrically similar conditions, with identical confinement strength and aspect ratio, larger charge structures led to extended initial gas flow and surface burning processes, resulting in greater reaction equivalence and violence at the casing fracture.Under constant charge volume and size, a stronger casing confinement accelerated self-enhanced burning, increasing the internal pressure, reaction degree, and reaction violence. Under a constant casing thickness and radius, higher aspect ratios led to a greater reaction violence at the casing fracture.Moreover, under a constant charge volume and casing thickness, higher aspect ratios resulted in a higher internal pressure, increased reaction degree, and greater reaction violence at the casing fracture. Further,larger ullage volumes extended the reaction evolution time and increased the reaction violence under constant casing dimensions. Through a matching design of the opening threshold of the pressure relief holes and the relief structure area, a stable burning reaction could be maintained until completion,thereby achieving a control of the reaction violence. The proposed model could effectively reflect the effects of the intrinsic burning rate, casing confinement strength, charge size, ullage volume, and pressure relief structure on the reaction evolution process and reaction violence, providing a theoretical method for the thermal safety design and reaction violence evaluation of melt-cast explosives.展开更多
The new CL-20(hexanitrohexaazaisowurtzitane)type aluminized explosives in the overdrive detonation(ODD)conditions of the core problem is how to accurately represent the state of the overdrive detonation products.To th...The new CL-20(hexanitrohexaazaisowurtzitane)type aluminized explosives in the overdrive detonation(ODD)conditions of the core problem is how to accurately represent the state of the overdrive detonation products.To this end,this paper is based on the impedance matching method to test the ODD conditions of CL-20 type aluminium explosive particle velocity.Calculated the interfacial pressure of the shock wave in different media.Determined the characteristic parameters of the reaction zone of the detonation of CL-20 aluminized explosives.Calibrated the parameters of the JoneseWilkinseLee(JWL)+γ equation for the detonation products(DPs).Revealed the effect of different DPs equation of state(EOS)on the Hugoniot pressure of ODD.The results indicate that when the content of aluminum powder ranges from 0%to 30%,the duration of the ODD reaction zone and the width of the detonation reaction zone of the CL-20-based aluminized explosive are directly proportional to the content of aluminum powder.The width of the detonation reaction zone is increased by 1.97 times to 2.7 times compared to that of the reaction zone without the addition of aluminum powder.However,the energy release efficiency of the detonation reaction zone is inversely proportional to the content of aluminum powder.When the aluminum powder content was held constant,the incorporation of AP caused a 25%reduction in the energy release efficiency of the detonation reaction zone.Compared with existing ODD state equations,the JWL +γ equation is superior in calibrating overpressure Hugoniot data and the isentropic expansion in the C-J state.The deviation between calculated pressure results and experimental measurements is within 6%.展开更多
In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-f...In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-field air-burst experiments are conducted.The damage modes and characteristics of the target plates are compared and analyzed.Each flat plate section is completely punctured,resulting in a penetration hole.The damage modes induced by the three charge types on the stiffened plate structure are consistent,characterized by shear failure in the central region of the flat plate due to penetration by the penetrator,localized plastic deformation of the flat plate,and local penetration failure resulting from partial perforation of the central stiffener.The penetration lengths caused by ELSC and ELEFP are 45.1%and 46.1% larger than that of LSC,while the half-width of the penetration hole generated by ELEFP is 54.2% and 24.7% smaller than that of ELSC and LSC,respectively.The penetration height caused by ELEFP are 17.5%and 62.1% larger than that of ELSC and LSC,respectively.The stiffener effectively segments the damage area,enhancing the local structural strength and limiting the extent of plastic deformation in the flat plate section.The comparative results show that the ELSC proves to be more effective for efficient large-scale damage,and ELEFP is more suitable for achieving efficient localized damage.展开更多
Reinforced concrete(RC)columns are often subjected to off-central explosion due to the uncertainty of blast locations.However,few studies have focused on the dynamic response of RC columns under offcentral explosions....Reinforced concrete(RC)columns are often subjected to off-central explosion due to the uncertainty of blast locations.However,few studies have focused on the dynamic response of RC columns under offcentral explosions.A field blast experiment was conducted under close-in explosion with varying detonation offset distances(0 m,0.5 m,and 1 m),the overpressure load and dynamic responses of the full-scale RC columns were measured.Compared with the centrally detonated condition,a relative offset distance of 1.67 decreases the maximum and residual deflections of the RC column by 16.8%and 21.4%,respectively,while increasing the maximum and residual support rotations by 24.7%and 17.8%.Based on the experimental results,a theoretical model was proposed that considers the detonation location and charge mass,boundary conditions,axial compression ratio and material properties.The theoretical model exhibited good agreement with the experimental results,with prediction errors below 10%for both maximum and residual deflection.The effects of parameters were analyzed,and it indicated that an increase in offset distance results in decreased maximum and residual deflections but an increased support angle,thereby exacerbating damage.Higher axial load ratio,span-depth ratio,and longitudinal reinforcement ratio reduce both deflections and support angle.Additionally,a rapid method to predict the maximum and residual deflection of RC columns under off-central blast loading was also proposed based on the Generalized Regression Neural Network(GRNN).Eleven features which related to the RC column properties and the blast characteristics were used in the training process of GRNN,and accurate predictions were achieved with prediction errors within 20%.This study fills the gap in predicting the dynamic response of RC columns under off-central explosion,providing valuable references for blast-resistant design.展开更多
Gravity-caisson wharves have been widely constructed in coastal and island regions, which are threaten by potential underwater explosions. This work aims to study the dynamic behaviors and propose a damage evaluation ...Gravity-caisson wharves have been widely constructed in coastal and island regions, which are threaten by potential underwater explosions. This work aims to study the dynamic behaviors and propose a damage evaluation approach of caisson wharf against underwater explosion. Firstly, based on both the underwater explosion loading test and underwater explosion test on the reduced-scale caisson specimen, a high-fidelity finite element analysis approach for numerically reproduce the dynamic behaviors of prototype caisson wharves against underwater explosions was proposed and verified. Secondly, the underwater explosion loadings and dynamic behaviors of prototype caisson wharf (14.9 m×8.1 m×10.95 m) against sequential blast wave and bubble pulsation of typical torpedo with a charge weight of 200 kg were studied. The influences of the seabed and cabin infill materials, as well as the explosion standoff distances of 3.4–10.2 m and depths of burst between 1/4 and 3/4 of water depth, on the blast resistance of caisson wharf were further examined through deflection distributions of exterior wall, damage evolution, and overall displacement of caisson wharf. Finally, a performance evaluation approach for prototype caisson wharves against underwater explosions was proposed by comprehensively considering the bearing, storage, and berthing capabilities. The corresponding protective measures and design recommendations were further provided. It indicates that: (i) under the explosion of a typical torpedo, the damage modes of prototype caisson wharf mainly involve the overall vibration, spalling and cracking of the exterior wall, collapse of the upper operating platform and cracking of the top plate;(ii) the blast wave and cavitation zone generated between the bubble and the exterior wall are the two primary causes of damage to caisson wharf;(iii) compared to the saturated calcareous sand seabed, the assumption of rigid seabed underestimates the spalling on the exterior wall, which is not recommended for scenarios where cavitation zones may generate;(iv) rock rubble is the most effective infill material in improving the blast resistance of caisson wharf among four types of infill configurations, i.e., fully filled and half-filled saturated calcareous sand, rock rubble and pure water;(v) the standoff distance of 10.2 m is regarded as a secure protective range in the scenarios discussed currently. As the standoff distance decreases and the depth of burst increases, the spalling of the exterior wall induced by the cavitation intensifies, posing a great threat to the functionality of caisson wharf.展开更多
The aerosolization and diffusion of radioactive materials caused by chemical explosions represent a typical nuclear accident scenario that poses severe radioactive hazards to human health and the environment.This stud...The aerosolization and diffusion of radioactive materials caused by chemical explosions represent a typical nuclear accident scenario that poses severe radioactive hazards to human health and the environment.This study examines the diffusion of plutonium aerosol generated by a chemical explosion within a typical representative underground facility.The state of explosion products following a single-point detonation of explosives was simulated.Subsequently,a numerical simulation of plutonium aerosol diffusion using the discrete phase model(DPM)was conducted based on the outcomes of the chemical explosion simulation.The simulation results indicate that plutonium aerosols diffuse throughout underground facilities after a chemical explosion;small particle size aerosols primarily accumulate in the upper part of the room after the accident;the concentrations of plutonium aerosol in the room and tunnel are significantly higher than those in the other areas;and the temporal variations in aerosol concentration in each area were quantified.Based on the particle concentration distribution and the effective dose computation approach,the study computes the internal irradiation dose received by personnel in seven areas over various time periods post-accident.Recommendations for emergency decision-making were derived from these calculations.These findings provide important theoretical insight and practical engineering application value for understanding the diffusion of radioactive aerosol in confined spaces following chemical explosions and for evaluating personnel radiation dose.展开更多
Explosive cyclones(ECs) are rapidly intensifying subtropical cyclones that can develop within a short time and pose considerable threats to coastal areas in middle and high latitudes.Gaining a comprehensive understand...Explosive cyclones(ECs) are rapidly intensifying subtropical cyclones that can develop within a short time and pose considerable threats to coastal areas in middle and high latitudes.Gaining a comprehensive understanding of their formation,evolution,and mechanisms of explosive development is essential for improving forecasts of extreme weather events and mitigating associated impacts.Potential vorticity(PV),which is closely related to cyclone dynamics,serves as a valuable diagnostic tool in the study of ECs.In this study,two wintertime ECs of differing intensity over the Northwestern Pacific Ocean are analyzed to examine how different atmospheric processes influence PV generation and the rapid development of ECs.The maximum deepening rates of the two ECs are 2.81 Bergeron(called EC1) and 1.52 Bergeron(referred to as EC2).Results indicate that different stages of EC evolution are closely associated with PV tendency changes at different atmospheric levels.Using the PV tendency equation,during the explosive development of EC1,latent heat release may trigger the downward propagation of upper-level PV.For EC2,latent heat release notably enhances low-level PV,directly contributing to its rapid intensification.To validate these findings,sensitivity tests are conducted using the Weather Research and Forecasting model,with latent heat release turned off in the microphysical scheme for both cases.The results confirm the crucial role of latent heat release in generating low-level PV,further revealing that latent heat release contributes more to the explosive development of EC2 than that of EC1.展开更多
Investigating the detonation reaction zone structures of high explosives is significant for understanding detonation reaction mechanism.This study employed an integrated approach combining machine learning prediction,...Investigating the detonation reaction zone structures of high explosives is significant for understanding detonation reaction mechanism.This study employed an integrated approach combining machine learning prediction,theoretical calculation,and experimental characterization to determine the detonation reaction zone width of CL-20-based aluminized explosive.In this study,the detonation reaction zone refers to the reaction zone between the von Neumann(VN)peak and sonic point,which usually means the so-called detonation driving zone(DDZ).For the machine learning prediction,an ensemble model integrating Random Forest and Support Vector Regression was developed to predict the reaction zone width using a dataset of 19 publicly available samples.For the theoretical calculation,the Wood-Kirkwood(W-K)detonation theory model was utilized to implement numerical calculation of the reaction zone structures,incorporating chemical reaction kinetics to describe the detonation reaction progress.In experimental characterization,the Photon Doppler Velocimetry(PDV)was applied with LiF as the optical window to measure the particle velocity profile of detonation products and derive the reaction zone width.The results indicate that the reaction zone width values are 0.25 mm,0.28 mm,and 0.26 mm obtained from machine learning prediction,theoretical calculation,and experimental characterization,respectively.The corresponding velocities at the Chapman-Jouguet(CJ)point are 1,938 m/s,2,047 m/s,and 1,982 m/s,respectively.The maximum relative deviation in reaction zone width among three methods is approximately 7.7%,while that for CJ particle velocity is approximately 3.3%.These results from all three methods agree well within engineering error.This validates the effectiveness of integrating machine learning prediction,theoretical calculation and advanced experimental techniques for studying the detonation reaction zone structures of high explosives.This research provides insights into the detonation reaction mechanism and reaction zone characteristics of CL-20-based aluminized explosive.展开更多
This paper presents a simplified design tool based on semi-analytical formulations to investigate the dynamic response of an immersed composite cylinder subjected to a far-field underwater explosion.The cylinder is si...This paper presents a simplified design tool based on semi-analytical formulations to investigate the dynamic response of an immersed composite cylinder subjected to a far-field underwater explosion.The cylinder is simply supported,fully submerged and filled with air inside.A classical shell theory using a Double Fourier series solution combined with the first-order Doubly Asymptotic Approximation(DAA1)formulation is adapted to model the fluid-structure interaction.An explicit non-standard finite difference scheme is applied to solve the coupled differential equations in time domain.The validity of DAA1 model is established by comparing the LS-DYNA/USA finite element results with existing experimental data from the literature.Then the proposed semi-analytical solutions are compared to the LS-DYNA/USA results,showing good correlation with a discrepancy of 7%for peak deflections and±9%for maximum stresses at the stand-off point for cylinders with relatively small length over radius ratios.Parametric studies examining the effect of different loading conditions,areal masses,and material configurations reveal that a large charge mass located far from the composite panel turns out to be more damaging than a small mass located nearby due to a broader pressure-time profile.Finally,the proposed model demonstrates a significant reduction in computation time,being approximately 30 times faster than its numerical counterpart,LS-DYNA/USA,making it a valuable tool for the preliminary design stages.展开更多
In order to improve the quality of loading and make the ammuni- tion safe in use,a new loading technique of ordered solidification has been studied.The study shows that the adoption of this new technique makes the cha...In order to improve the quality of loading and make the ammuni- tion safe in use,a new loading technique of ordered solidification has been studied.The study shows that the adoption of this new technique makes the charge more compact and brings about a satisfactory supplement of liquid ex- plosives,thus increasing the charge density,which is most advantageous to the crimination of pores,cavities,gaps at the bottom and in loose struc- tures.The physical mechanical properties of the charge are hence greatly im- proved,and the sensitivity of the charge to environmental stimulations is much lowered.展开更多
文摘Aluminum（Al） powders are used in composite explosives as a typical reducing agent for improving explosion performance. To understand energy release of aluminum in aluminized RDX-based explosives, a series of thermal measurements and underwater explosion（UNDEX） experiments were conducted. Lithium fluoride（LiF） was added in RDX-based explosives, as a replacement of aluminum, and used in constant temperature calorimeter experiments and UNDEXs. The influence of aluminum powder on explosion heat（Qv） was measured. A rich supply of data about aluminum energy release rate was gained. There are other oxides（CO2, CO, and H2O） in detonation products besides alumina when the content of RDX is maintained at the same levels. Aluminum cannot fully combine with oxygen in the detonation products. To study the relationship between the explosive formulation and energy release, pressure and impulse signals in underwater experiments were recorded and analyzed after charges were initiated underwater. The shock wave energy（Esk）, bubble energy（Eb）, and total energy（Et） monotony increase with the Al/O ratio, while the growth rates of the shock wave energy,bubble energy, and total energy become slow.
基金supported by the Natural Science Research Excellent Youth Project of Anhui Educational Committee(Grant No.2023AH020026)and the National Natural Science Foundation of China(Grant No.12272001)the authors would like to thank the foundation for the financial supports.
文摘To investigate the coupling mechanisms of detonation energy release between the TiH_(2)/PTFE active shell and RDX explosive,an RDX-based active shell thermobaric explosive containing TiH_(2)/PTFE powders was prepared.The effects of the TiH_(2)/PTFE mass ratio on the shock wave parameters and afterburning effect of the thermobaric explosives were investigated.The energy release characteristics of the optimal TiH_(2)/PTFE ratio under varying vacuum degrees were evaluated using a 0.9 m3 spherical explosive chamber and colorimetric thermometry method.The experimental results demonstrated that as the PTFE powders content in the active shell increased,the shock wave intensity,explosion fireball duration,and maximum average temperature of the thermobaric explosives initially increased and then decreased,peaking at a TiH_(2)/PTFE mass ratio of 1:1.Compared to the TiH_(2)-based thermobaric explosives without PTFE,the 1:1 TiH_(2)/PTFE formulation exhibited increases of 45.9%in peak overpressure,69.7%in fireball duration,and 7.2%in maximum average temperature.Thus,an optimal PTFE content significantly enhances the energy release efficiency of the RDX/TiH_(2)/PTFE thermobaric explosives.Furthermore,the energy release efficiency of thermobaric explosives was influenced by the vacuum degree,with the maximum average temperature,peak overpressure,positive impulse,positive pressure action time,and fireball duration decreasing by 10.8%,35.3%,52.1%,65.5%,and 46.4%,respectively,as the vacuum degree increased from 0 to 52.4%.
基金The authors would like to acknowledge National Natural Science Foundation of China(Grant No.11832006)Open Project of State Key Laboratory of Explosion Science and Technology in Beijing Institute of Technology(Grant No.KFJJ20-04 M)to provide fund for conducting experiments.
文摘Nano-sized aluminum(Nano-Al)powders hold promise in enhancing the total energy of explosives and the metal acceleration ability at the same time.However,the near-detonation zone effects of reaction between Nano-Al with detonation products remain unclear.In this study,the overall reaction process of 170 nm Al with RDX explosive and its effect on detonation characteristics,detonation reaction zone,and the metal acceleration ability were comprehensively investigated through a variety of experiments such as the detonation velocity test,detonation pressure test,explosive/window interface velocity test and confined plate push test using high-resolution laser interferometry.Lithium fluoride(LiF),which has an inert behavior during the explosion,was used as a control to compare the contribution of the reaction of aluminum.A thermochemical approach that took into account the reactivity of aluminum and ensuing detonation products was adopted to calculate the additional energy release by afterburn.Combining the numerical simulations based on the calculated afterburn energy and experimental results,the parameters in the detonation equation of state describing the Nano-Al reaction characteristics were calibrated.This study found that when the 170 nm Al content is from 0%to 15%,every 5%increase of aluminum resulted in about a 1.3%decrease in detonation velocity.Manganin pressure gauge measurement showed no significant enhancement in detonation pressure.The detonation reaction time and reaction zone length of RDX/Al/wax/80/15/5 explosive is 64 ns and 0.47 mm,which is respectively 14%and 8%higher than that of RDX/wax/95/5 explosive(57 ns and 0.39 mm).Explosive/window interface velocity curves show that 170 nm Al mainly reacted with the RDX detonation products after the detonation front.For the recording time of about 10 ms throughout the plate push test duration,the maximum plate velocity and plate acceleration time accelerated by RDX/Al/wax/80/15/5 explosive is 12%and 2.9 ms higher than that of RDX/LiF/wax/80/15/5,respectively,indicating that the aluminum reaction energy significantly increased the metal acceleration time and ability of the explosive.Numerical simulations with JWLM explosive equation of state show that when the detonation products expanded to 2 times the initial volume,over 80%of the aluminum had reacted,implying very high reactivity.These results are significant in attaining a clear understanding of the reaction mechanism of Nano-Al in the development of aluminized explosives.
基金supported by the National Natural Science Foundation of China(Grant Nos.12002156,11972185,12372136)Research Fund of State Key Laboratory of Mechanics and Control for Aerospace Structures(Grant No.MCMS-I-0222K01)。
文摘While the moisture content of soil affects significantly the blast impulse of shallow buried explosives,the role of surface-covering water(SCW)on soil in such blast impulse remains elusive.A combined experimental and numerical study has been carried out to characterize the effect of SCW on transferred impulse and loading magnitude of shallow buried explosives.Firstly,blast tests of shallow buried explosives were conducted,with and without the SCW,to quantitatively assess the blast loading impulse.Subsequently,finite element(FE)simulations were performed and validated against experimental measurement,with good agreement achieved.The validated FE model was then employed to predict the dynamic response of a fully-clamped metallic circular target,subjected to the explosive impact of shallow buried explosives with SCW,and explore the corresponding physical mechanisms.It was demonstrated that shallow buried explosives in saturated soil generate a greater impulse transferred towards the target relative to those in dry soil.The deformation displacement of the target plate is doubled.Increasing the height of SCW results in enhanced center peak deflection of the loaded target,accompanied by subsequent fall,due to the variation of deformation pattern of the loaded target from concentrated load to uniform load.Meanwhile,the presence of SCW increases the blast impulse transferred towards the target by three times.In addition,there exists a threshold value of the burial depth that maximizes the impact impulse.This threshold exhibits a strong sensitivity to SCW height,decreasing with increasing SCW height.An empirical formula for predicting threshold has been provided.Similar conclusions can be drawn for different explosive masses.The results provide technical guidance on blast loading intensity and its spatial distribution considering shallow buried explosives in coast-land battlefields,which can ultimately contribute to better protective designs.
基金supported by the fundamental research funds of Zhejiang Sci-Tech University(No.22212286-Y)the Natural Science Foundation of Zhejiang Province(No.LQ24B040003)。
文摘Aromatic nitro compounds present substantial health and environmental concerns due to their toxic nature and potential explosive properties.Consequently,the development of host–vip molecular recognition systems for these compounds serves a dual-purpose:enabling the fabrication of high-performance sensors for detection and guiding the design of efficient adsorbents for environmental remediation.This study investigated the host–vip recognition behavior of perethylated pillar[n]arenes toward two aromatic nitro molecules,1-chloro-2,4-dinitrobenzene and picric acid.Various techniques including^(1)H NMR,2D NOESY NMR,and UV-vis spectroscopy were employed to explore the binding behavior between pillararenes and aromatic nitro vips in solution.Moreover,valuable single crystal structures were obtained to elucidate the distinct solid-state assembly behaviors of these vips with different pillararenes.The assembled solid-state supramolecular structures observed encompassed a 1:1 host–vip inclusion complex,an external binding complex,and an exo-wall tessellation complex.Furthermore,based on the findings from these systems,a pillararene-based test paper was developed for efficient picric acid detection,and the removal of picric acid from solution was also achieved using pillararenes powder.This research provides novel insights into the development of diverse host–vip systems toward hazardous compounds,offering potential applications in environmental protection and explosive detection domains.
基金supported in part by the National Natural Science Foundation of China(Nos.12335018,12105264,and 12275248)NSAF Joint Fund Project(Nos.U2230107,U1730244,U2130207)+1 种基金Innovation and Development Fund of China Academy of Engineering Physics(No.CXKS20240052)Central Guidance for Local Science and Technology Development Fund Project(No.2023ZYDF075).
文摘The current work addresses the challenge of elucidating the performance of fluoroelastomers within the HMX(octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine)based polymer-bonded explosives(PBXs).To simulate the confined interface in PBXs,bilayer films of F2314/HMX and F2311/HMX were designed.Neutron reflectivity(NR),nanoindentation,and X-ray reflectivity(XRR)were employed to examine the layer thickness,interface characteristics,diffusion behavior,and surface morphology of the bilayers.NR measurements revealed interface thicknesses of 45Å and 98Å for F2314/HMX and F2311/HMX,respectively,indicating deeper penetration of F2311 into the HMX matrix.NR also suggested a denser polymer network with a higher scattering length density(SLD)near the HMX interface for both fluoroelastomers,while the bound layer of F2311 was notably thicker.Nanoindentation cross-checks and confirms the presence of a bound layer,highlighting the differences in stiffness and diffusion ability between the two polymers.The consistency between the NR and nanoindentation results suggests that F2311 demonstrates better flexibility and elasticity,whereas F2314 is stiffer and more plastic.Accordingly,the structures and performances of different fluoroelastomers at the HMX interface are discussed,which can provide valuable insights into the selection of binders for PBX formulations tailored to specific applications.
基金supported by the National Natural Science Foundation of China(Gant Nos.11372291 and 11902298)。
文摘Detonation performance is crucial for evaluating the power of high explosives(HEs),and the equation of state(EOS)that accurately describes the high-temperature,high-pressure,and high-temperature,medium-pressure states of detonation products is key to assessing the damage efficiency of these energetic materials.This article examines the limitations of the VLW EOS in representing the thermodynamic states of explosive detonation gas products under high-temperature and medium-to high-pressure conditions.A new gas EOS for detonation products,called VHL(Virial-Han-Long),is proposed.The accuracy of VHL in describing gas states under high-temperature and medium-to high-pressure conditions is verified,and its performance in evaluating explosive detonation and working capabilities is explored.The results demonstrate that VHL exhibits high precision in calculating detonation performance.Subsequently,the detonation performance of three new HEs(ICM-101,ONC,and TNAZ)was calculated and compared to traditional HEs(TATB,CL-20,and HMX).The results indicate that ONC has superior detonation performance compared to the other explosives,while ICM-101 shows a detonation velocity similar to CL-20 but with slightly lower detonation pressure.The detonation characteristics of TNAZ are comparable to those of the standard HE HMX.From the perspective of products,considering the comprehensive work performance(mechanical work and detonation heat),both ONC and ICM-101demonstrate relatively superior performance.
基金supported by the National Natural Science Foundation of China(Grant Nos.12302435 and 12221002)。
文摘Shock wave caused by a sudden release of high-energy,such as explosion and blast,usually affects a significant range of areas.The utilization of a uniform fine mesh to capture sharp shock wave and to obtain precise results is inefficient in terms of computational resource.This is particularly evident when large-scale fluid field simulations are conducted with significant differences in computational domain size.In this work,a variable-domain-size adaptive mesh enlargement(vAME)method is developed based on the proposed adaptive mesh enlargement(AME)method for modeling multi-explosives explosion problems.The vAME method reduces the division of numerous empty areas or unnecessary computational domains by adaptively suspending enlargement operation in one or two directions,rather than in all directions as in AME method.A series of numerical tests via AME and vAME with varying nonintegral enlargement ratios and different mesh numbers are simulated to verify the efficiency and order of accuracy.An estimate of speedup ratio is analyzed for further efficiency comparison.Several large-scale near-ground explosion experiments with single/multiple explosives are performed to analyze the shock wave superposition formed by the incident wave,reflected wave,and Mach wave.Additionally,the vAME method is employed to validate the accuracy,as well as to investigate the performance of the fluid field and shock wave propagation,considering explosive quantities ranging from 1 to 5 while maintaining a constant total mass.The results show a satisfactory correlation between the overpressure versus time curves for experiments and numerical simulations.The vAME method yields a competitive efficiency,increasing the computational speed to 3.0 and approximately 120,000 times in comparison to AME and the fully fine mesh method,respectively.It indicates that the vAME method reduces the computational cost with minimal impact on the results for such large-scale high-energy release problems with significant differences in computational domain size.
基金supported by the National Natural Science Foundation of China (Grant Nos. 22475179 and 22275173)。
文摘Realizing effective enhancement in the thermally conductive performance of polymer bonded explosives(PBXs) is vital for improving the resultant environmental adaptabilities of the PBXs composites. Herein, a kind of primary-secondary thermally conductive network was designed by water-suspension granulation, surface coating, and hot-pressing procedures in the graphene-based PBXs composites to greatly increase the thermal conductive performance of the composites. The primary network with a threedimensional structure provided the heat-conducting skeleton, while the secondary network in the polymer matrix bridged the primary network to increase the network density. The enhancement efficiency in the thermally conductive performance of the composites reached the highest value of 59.70% at a primary-secondary network ratio of 3:1. Finite element analysis confirmed the synergistic enhancement effect of the primary and secondary thermally conductive networks. This study introduces an innovative approach to designing network structures for PBX composites, significantly enhancing their thermal conductivity.
基金supported by the National Natural Science Foundation of China(Grant Nos.52171318 and 12202329)Joint Foundation of the Ministry of Education(Grant No.8091B022105)。
文摘The detonation of fuel-rich explosives yields combustible products that persistently burn upon mixing with ambient oxygen,releasing additional energy through a phenomenon known as the afterburning effect.This process greatly influences the evolution of confined blast loading and the subsequent structural response,which is crucial in confined blast scenarios.Given the complex nature of the reaction process,accurate analysis of the afterburning effect remains challenging.Previous studies have either overlooked the mechanisms of detonation product combustion or failed to provide experimental validation.This study introduces a three-dimensional model to effectively characterize the combustion of detonation products.The model integrates chemical reaction source terms into the governing equations to consider the combustion processes.Numerical simulations and experimental tests were conducted to analyze the combustion and energy release from the detonation products of fuel-rich explosives in confined spaces.Approximately 50%of the energy was released during the combustion of detonation products in a confined TNT explosion.Although the combustion of these products was much slower than the detonation process,it aligned with the dynamic response of the structure,which enhanced the explosive yield.Excluding afterburning from the analysis reduced the center-point deformation of the structure by 30%.Following the inclusion of afterburning,the simulated quasistatic pressure increased by approximately 45%.Subsequent comparisons highlighted the merits of the proposed approach over conventional methods.This approach eliminates the reliance on empirical parameters,such as the amount and rate of energy release during afterburning,thereby laying the foundation for understanding load evolution in more complex environments,such as ships,buildings,and underground tunnels.
基金supported by the National Natural Science Foundation of China (Grant No. 12002044)。
文摘DNAN-based insensitive melt-cast explosives have been widely utilized in insensitive munition in recent years. When constrained DNAN-based melt-cast explosives are ignited under thermal stimulation, the base explosive exists in a molten liquid state, where high-temperature gases expand and react in the form of bubble clouds within the liquid explosive;this process is distinctly different from the dynamic crack propagation process observed in the case of solid explosives. In this study, a control model for the reaction evolution of burning-bubble clouds was established to describe the reaction process and quantify the reaction violence of DNAN-based melt-cast explosives, considering the size distribution and activation mechanism of the burning-bubble clouds. The feasibility of the model was verified through experimental results. The results revealed that under geometrically similar conditions, with identical confinement strength and aspect ratio, larger charge structures led to extended initial gas flow and surface burning processes, resulting in greater reaction equivalence and violence at the casing fracture.Under constant charge volume and size, a stronger casing confinement accelerated self-enhanced burning, increasing the internal pressure, reaction degree, and reaction violence. Under a constant casing thickness and radius, higher aspect ratios led to a greater reaction violence at the casing fracture.Moreover, under a constant charge volume and casing thickness, higher aspect ratios resulted in a higher internal pressure, increased reaction degree, and greater reaction violence at the casing fracture. Further,larger ullage volumes extended the reaction evolution time and increased the reaction violence under constant casing dimensions. Through a matching design of the opening threshold of the pressure relief holes and the relief structure area, a stable burning reaction could be maintained until completion,thereby achieving a control of the reaction violence. The proposed model could effectively reflect the effects of the intrinsic burning rate, casing confinement strength, charge size, ullage volume, and pressure relief structure on the reaction evolution process and reaction violence, providing a theoretical method for the thermal safety design and reaction violence evaluation of melt-cast explosives.
基金supported by the National Natural Science Foundation of China(NSFC,Grant Nos.11872120,12102050)Key Laboratory of Explosion Science and Technology(Grant No.QNKT22-01).
文摘The new CL-20(hexanitrohexaazaisowurtzitane)type aluminized explosives in the overdrive detonation(ODD)conditions of the core problem is how to accurately represent the state of the overdrive detonation products.To this end,this paper is based on the impedance matching method to test the ODD conditions of CL-20 type aluminium explosive particle velocity.Calculated the interfacial pressure of the shock wave in different media.Determined the characteristic parameters of the reaction zone of the detonation of CL-20 aluminized explosives.Calibrated the parameters of the JoneseWilkinseLee(JWL)+γ equation for the detonation products(DPs).Revealed the effect of different DPs equation of state(EOS)on the Hugoniot pressure of ODD.The results indicate that when the content of aluminum powder ranges from 0%to 30%,the duration of the ODD reaction zone and the width of the detonation reaction zone of the CL-20-based aluminized explosive are directly proportional to the content of aluminum powder.The width of the detonation reaction zone is increased by 1.97 times to 2.7 times compared to that of the reaction zone without the addition of aluminum powder.However,the energy release efficiency of the detonation reaction zone is inversely proportional to the content of aluminum powder.When the aluminum powder content was held constant,the incorporation of AP caused a 25%reduction in the energy release efficiency of the detonation reaction zone.Compared with existing ODD state equations,the JWL +γ equation is superior in calibrating overpressure Hugoniot data and the isentropic expansion in the C-J state.The deviation between calculated pressure results and experimental measurements is within 6%.
基金supported by the National Natural Science Foundation of China(Grant Nos.52271307,52061135107,52192692,11802025)the Liao Ning Excellent Youth Fund Program(Grant No.2023JH3/10200012)+1 种基金the Liao Ning Revitalization Tal-ents Program(Grant No.XLYC1908027)the Fundamental Research Funds for the Central Universities(Grant Nos.DUT20RC(3)025,DUT20TD108,DUT20LAB308)。
文摘In order to investigate the penetration performance of Linear-Shaped Charge(LSC),Embowed LinearShaped Charge(ELSC),and Embowed Linear Explosively Formed Projectile(ELEFP)on T-shaped stiffened plates,a series of near-field air-burst experiments are conducted.The damage modes and characteristics of the target plates are compared and analyzed.Each flat plate section is completely punctured,resulting in a penetration hole.The damage modes induced by the three charge types on the stiffened plate structure are consistent,characterized by shear failure in the central region of the flat plate due to penetration by the penetrator,localized plastic deformation of the flat plate,and local penetration failure resulting from partial perforation of the central stiffener.The penetration lengths caused by ELSC and ELEFP are 45.1%and 46.1% larger than that of LSC,while the half-width of the penetration hole generated by ELEFP is 54.2% and 24.7% smaller than that of ELSC and LSC,respectively.The penetration height caused by ELEFP are 17.5%and 62.1% larger than that of ELSC and LSC,respectively.The stiffener effectively segments the damage area,enhancing the local structural strength and limiting the extent of plastic deformation in the flat plate section.The comparative results show that the ELSC proves to be more effective for efficient large-scale damage,and ELEFP is more suitable for achieving efficient localized damage.
基金financially supported by the National Natural Science Foundation of China(Grants No.12472399)。
文摘Reinforced concrete(RC)columns are often subjected to off-central explosion due to the uncertainty of blast locations.However,few studies have focused on the dynamic response of RC columns under offcentral explosions.A field blast experiment was conducted under close-in explosion with varying detonation offset distances(0 m,0.5 m,and 1 m),the overpressure load and dynamic responses of the full-scale RC columns were measured.Compared with the centrally detonated condition,a relative offset distance of 1.67 decreases the maximum and residual deflections of the RC column by 16.8%and 21.4%,respectively,while increasing the maximum and residual support rotations by 24.7%and 17.8%.Based on the experimental results,a theoretical model was proposed that considers the detonation location and charge mass,boundary conditions,axial compression ratio and material properties.The theoretical model exhibited good agreement with the experimental results,with prediction errors below 10%for both maximum and residual deflection.The effects of parameters were analyzed,and it indicated that an increase in offset distance results in decreased maximum and residual deflections but an increased support angle,thereby exacerbating damage.Higher axial load ratio,span-depth ratio,and longitudinal reinforcement ratio reduce both deflections and support angle.Additionally,a rapid method to predict the maximum and residual deflection of RC columns under off-central blast loading was also proposed based on the Generalized Regression Neural Network(GRNN).Eleven features which related to the RC column properties and the blast characteristics were used in the training process of GRNN,and accurate predictions were achieved with prediction errors within 20%.This study fills the gap in predicting the dynamic response of RC columns under off-central explosion,providing valuable references for blast-resistant design.
基金supported by National Natural Science Foundations of China(Grant No.52308522).
文摘Gravity-caisson wharves have been widely constructed in coastal and island regions, which are threaten by potential underwater explosions. This work aims to study the dynamic behaviors and propose a damage evaluation approach of caisson wharf against underwater explosion. Firstly, based on both the underwater explosion loading test and underwater explosion test on the reduced-scale caisson specimen, a high-fidelity finite element analysis approach for numerically reproduce the dynamic behaviors of prototype caisson wharves against underwater explosions was proposed and verified. Secondly, the underwater explosion loadings and dynamic behaviors of prototype caisson wharf (14.9 m×8.1 m×10.95 m) against sequential blast wave and bubble pulsation of typical torpedo with a charge weight of 200 kg were studied. The influences of the seabed and cabin infill materials, as well as the explosion standoff distances of 3.4–10.2 m and depths of burst between 1/4 and 3/4 of water depth, on the blast resistance of caisson wharf were further examined through deflection distributions of exterior wall, damage evolution, and overall displacement of caisson wharf. Finally, a performance evaluation approach for prototype caisson wharves against underwater explosions was proposed by comprehensively considering the bearing, storage, and berthing capabilities. The corresponding protective measures and design recommendations were further provided. It indicates that: (i) under the explosion of a typical torpedo, the damage modes of prototype caisson wharf mainly involve the overall vibration, spalling and cracking of the exterior wall, collapse of the upper operating platform and cracking of the top plate;(ii) the blast wave and cavitation zone generated between the bubble and the exterior wall are the two primary causes of damage to caisson wharf;(iii) compared to the saturated calcareous sand seabed, the assumption of rigid seabed underestimates the spalling on the exterior wall, which is not recommended for scenarios where cavitation zones may generate;(iv) rock rubble is the most effective infill material in improving the blast resistance of caisson wharf among four types of infill configurations, i.e., fully filled and half-filled saturated calcareous sand, rock rubble and pure water;(v) the standoff distance of 10.2 m is regarded as a secure protective range in the scenarios discussed currently. As the standoff distance decreases and the depth of burst increases, the spalling of the exterior wall induced by the cavitation intensifies, posing a great threat to the functionality of caisson wharf.
文摘The aerosolization and diffusion of radioactive materials caused by chemical explosions represent a typical nuclear accident scenario that poses severe radioactive hazards to human health and the environment.This study examines the diffusion of plutonium aerosol generated by a chemical explosion within a typical representative underground facility.The state of explosion products following a single-point detonation of explosives was simulated.Subsequently,a numerical simulation of plutonium aerosol diffusion using the discrete phase model(DPM)was conducted based on the outcomes of the chemical explosion simulation.The simulation results indicate that plutonium aerosols diffuse throughout underground facilities after a chemical explosion;small particle size aerosols primarily accumulate in the upper part of the room after the accident;the concentrations of plutonium aerosol in the room and tunnel are significantly higher than those in the other areas;and the temporal variations in aerosol concentration in each area were quantified.Based on the particle concentration distribution and the effective dose computation approach,the study computes the internal irradiation dose received by personnel in seven areas over various time periods post-accident.Recommendations for emergency decision-making were derived from these calculations.These findings provide important theoretical insight and practical engineering application value for understanding the diffusion of radioactive aerosol in confined spaces following chemical explosions and for evaluating personnel radiation dose.
基金financially supported by the National Key R&D Program of China (No. 2022YFC3004204)the National Natural Science Foundation of China (No. 42275001)the Natural Science Foundation of Shandong Province (No. ZR2022MD038)。
文摘Explosive cyclones(ECs) are rapidly intensifying subtropical cyclones that can develop within a short time and pose considerable threats to coastal areas in middle and high latitudes.Gaining a comprehensive understanding of their formation,evolution,and mechanisms of explosive development is essential for improving forecasts of extreme weather events and mitigating associated impacts.Potential vorticity(PV),which is closely related to cyclone dynamics,serves as a valuable diagnostic tool in the study of ECs.In this study,two wintertime ECs of differing intensity over the Northwestern Pacific Ocean are analyzed to examine how different atmospheric processes influence PV generation and the rapid development of ECs.The maximum deepening rates of the two ECs are 2.81 Bergeron(called EC1) and 1.52 Bergeron(referred to as EC2).Results indicate that different stages of EC evolution are closely associated with PV tendency changes at different atmospheric levels.Using the PV tendency equation,during the explosive development of EC1,latent heat release may trigger the downward propagation of upper-level PV.For EC2,latent heat release notably enhances low-level PV,directly contributing to its rapid intensification.To validate these findings,sensitivity tests are conducted using the Weather Research and Forecasting model,with latent heat release turned off in the microphysical scheme for both cases.The results confirm the crucial role of latent heat release in generating low-level PV,further revealing that latent heat release contributes more to the explosive development of EC2 than that of EC1.
文摘Investigating the detonation reaction zone structures of high explosives is significant for understanding detonation reaction mechanism.This study employed an integrated approach combining machine learning prediction,theoretical calculation,and experimental characterization to determine the detonation reaction zone width of CL-20-based aluminized explosive.In this study,the detonation reaction zone refers to the reaction zone between the von Neumann(VN)peak and sonic point,which usually means the so-called detonation driving zone(DDZ).For the machine learning prediction,an ensemble model integrating Random Forest and Support Vector Regression was developed to predict the reaction zone width using a dataset of 19 publicly available samples.For the theoretical calculation,the Wood-Kirkwood(W-K)detonation theory model was utilized to implement numerical calculation of the reaction zone structures,incorporating chemical reaction kinetics to describe the detonation reaction progress.In experimental characterization,the Photon Doppler Velocimetry(PDV)was applied with LiF as the optical window to measure the particle velocity profile of detonation products and derive the reaction zone width.The results indicate that the reaction zone width values are 0.25 mm,0.28 mm,and 0.26 mm obtained from machine learning prediction,theoretical calculation,and experimental characterization,respectively.The corresponding velocities at the Chapman-Jouguet(CJ)point are 1,938 m/s,2,047 m/s,and 1,982 m/s,respectively.The maximum relative deviation in reaction zone width among three methods is approximately 7.7%,while that for CJ particle velocity is approximately 3.3%.These results from all three methods agree well within engineering error.This validates the effectiveness of integrating machine learning prediction,theoretical calculation and advanced experimental techniques for studying the detonation reaction zone structures of high explosives.This research provides insights into the detonation reaction mechanism and reaction zone characteristics of CL-20-based aluminized explosive.
基金supported by French Defense Innovation Agency(AID-DGA)(Grant No.ANR-21-ASM2-0002-02)in the framework of the Astrid Maturation SUCCESS+project,a collaborative French research project.
文摘This paper presents a simplified design tool based on semi-analytical formulations to investigate the dynamic response of an immersed composite cylinder subjected to a far-field underwater explosion.The cylinder is simply supported,fully submerged and filled with air inside.A classical shell theory using a Double Fourier series solution combined with the first-order Doubly Asymptotic Approximation(DAA1)formulation is adapted to model the fluid-structure interaction.An explicit non-standard finite difference scheme is applied to solve the coupled differential equations in time domain.The validity of DAA1 model is established by comparing the LS-DYNA/USA finite element results with existing experimental data from the literature.Then the proposed semi-analytical solutions are compared to the LS-DYNA/USA results,showing good correlation with a discrepancy of 7%for peak deflections and±9%for maximum stresses at the stand-off point for cylinders with relatively small length over radius ratios.Parametric studies examining the effect of different loading conditions,areal masses,and material configurations reveal that a large charge mass located far from the composite panel turns out to be more damaging than a small mass located nearby due to a broader pressure-time profile.Finally,the proposed model demonstrates a significant reduction in computation time,being approximately 30 times faster than its numerical counterpart,LS-DYNA/USA,making it a valuable tool for the preliminary design stages.
文摘In order to improve the quality of loading and make the ammuni- tion safe in use,a new loading technique of ordered solidification has been studied.The study shows that the adoption of this new technique makes the charge more compact and brings about a satisfactory supplement of liquid ex- plosives,thus increasing the charge density,which is most advantageous to the crimination of pores,cavities,gaps at the bottom and in loose struc- tures.The physical mechanical properties of the charge are hence greatly im- proved,and the sensitivity of the charge to environmental stimulations is much lowered.
