The pavement performance of epoxy resin modified asphalt mixtures was investigated by the Marshall test, the indirect tensile test, the rutting test, the three-pointed bending test and the composite beam fatigue test....The pavement performance of epoxy resin modified asphalt mixtures was investigated by the Marshall test, the indirect tensile test, the rutting test, the three-pointed bending test and the composite beam fatigue test. In comparison with the performance of epoxy resin modified asphalt mixtures, the performance of stone matrix asphalt mixtures （SMA10） was also investigated. The rutting test and composite beam fatigue test results show that the epoxy resin modified asphalt mixtures can improve permanent deformation and fatigue characteristics. They also show lower temperature susceptibility and greater resistance to moisture damage compared to the SMA10. Findings from the research indicate that the epoxy resin modified asphalt mixture provides an optional material for the pavement of long-span steel bridges in China due to profound performance and economic advantages.展开更多
Shear resistance properties of the virgin bitumen and modified bitumen binders with Tafpack Super(TPS) modifier and SBS modified bitumen were discussed.Dynamic shear rheometer(DSR) was used to measure the laboratory c...Shear resistance properties of the virgin bitumen and modified bitumen binders with Tafpack Super(TPS) modifier and SBS modified bitumen were discussed.Dynamic shear rheometer(DSR) was used to measure the laboratory creep data for these binders over a wide range of constant shear stresses at 20 ℃ to characterize the shear creep behaviors of all kinds of asphalt binders,and the rutting test system was used to investigate the permanent deformation of porous asphalt mixtures using the above bitumen binders for a fixed compressive stress.The shear strain rate and shear creep modulus were used to characterize the shear creep behavior of the TPS modified bitumen,and the rutting test results were used to show the consistency of porous asphalt mixtures with the bitumen binders.Results indicate that a distinction of shear creep strain can be made among different contents of TPS modified bitumen at the same stress level,where the shear creep strain-time response curve of the SBS modified bitumen binder is between the curves of the 8% TPS and 12% TPS modified bitumen binders.The shear strain rate and the shear creep modulus of the TPS modified bitumen binders are obtained to compare with those of the SBS modified bitumen binder which results in the same trend as the shear creep strain-time response curve.Permanent deformation results of all the porous asphalt mixtures from the rutting test show reasonable agreement with the findings of the shear strain rates and shear creep modulus over the range of shear stress levels.展开更多
For the resource utilization of the solid waste coking sulfur paste and the improvement of performance of the asphalt mixture,a method for preparing modified asphalt mixture with coking sulfur paste modifier(CSPM)is h...For the resource utilization of the solid waste coking sulfur paste and the improvement of performance of the asphalt mixture,a method for preparing modified asphalt mixture with coking sulfur paste modifier(CSPM)is herein proposed.Compared with the matrix asphalt mixture,the Marshall stability of the 30%CSPM modified asphalt mixture increased by 38.3%,the dynamic stability increased by nearly one time(reaching 1847.5 times/mm),the splitting strength ratio increased by 39.3%while the splitting tensile strength decreased by 11.7%.After curing,the performance of the CSPM modified asphalt mixture was further improved.The results show that CSPM improved the high temperature stability and water damage resistance of the asphalt mixture,and the low-temperature anti-cracking performance of that was slightly reduced.Chemical analysis of asphalt binders shows that a little sulfur reacted with asphalt to produce polysulfide compounds(R-Sx-R′),and a part of sulfur existed in the form of crystalline sulfur which was further increased after curing.The presence of crystalline sulfur as an inorganic filler is the key point for improving the high temperature stability and water resistance performance of modified asphalt mixture.展开更多
Based on the analysis of the main failures discovered in pavement on steel deck plate and the demanding service condition of the pavement on steel deck, high-temperature rutting test, low-temperature bending test and ...Based on the analysis of the main failures discovered in pavement on steel deck plate and the demanding service condition of the pavement on steel deck, high-temperature rutting test, low-temperature bending test and controlled stress flexural fatigue test are used to study the performance of asphalt mixtures modified by epoxy resin including high-temperature stability, low-temperature cracking-resistance, and fatigue cracking-resistance, which are served to evaluate the modification effect of epoxy resin of different contents. With the addition of epoxy resin, all the three performances are improved greatly. However, when the amount of epoxy resin added is over a certain value, the modification effect will be stable with no extra benefit detected. Finally, in terms of the properties of the three respects, 20%, 30%, 30% are given separately as the proposal adding contents.展开更多
In recent decades,modified asphalt materials have been used in enhancing the traffic load on the roads.The main objective of this paper is to explore the modifi cation effect of direct coal liquefaction residue(DCLR)o...In recent decades,modified asphalt materials have been used in enhancing the traffic load on the roads.The main objective of this paper is to explore the modifi cation effect of direct coal liquefaction residue(DCLR)on as-phalt binders and investigate the effectiveness of DCLR in improving the performance of asphalt road.This paper prepared modifi ed petroleum as-phalt under diff erent process conditions and tested its penetration,softening point and ductility index.Based on the experimental data,according to gray correlation degree,the performance for the asphalt was compared.The performance for the modified asphalt is simulated and predicted using poly-nomial functions.The modifi ed asphalt was analyzed by FT-IR,TGA,SEM and HPLC.The results show that the optimal process conditions for DCLR modifi ed asphalt are shear mixing time of 45 min,shear mixing tempera-ture of 150℃ and shear mixing rate of 4000 r/min.The predicted fit with the experimental data of 0.993 further demonstrates the effectiveness of the method.The characterization results show no significant chemical change between the DCLR and the asphalt.DCLR can significantly improve the high temperature performance and water stability of the asphalt,but it has little impact on its low temperature performance.展开更多
Rheological characteristics of fiber-modified asphalt mixture were investigated.Cellulous fiber,polyester fiber and mineral fiber were used as additives for asphalt mixture,and the dosages were 0.3%,0.3%,0.4%,respecti...Rheological characteristics of fiber-modified asphalt mixture were investigated.Cellulous fiber,polyester fiber and mineral fiber were used as additives for asphalt mixture,and the dosages were 0.3%,0.3%,0.4%,respectively.Dynamic modulus test using superpave simple performance tester(SPT) was adopted to study the dynamic modulus and phase angle for the control mixture and fiber-modified ones at various temperatures and frequencies.Test results show that the rheological properties can be improved significantly by the addition of various fibers.The dynamic modulus increases with the increase of frequency,and the phase angle decreases with the increase of frequency.When various fibers are used,the dynamic modulus increases and phase angle decreases at each frequency.This indicates that the stiffness and the elastic portion of fiber-modified asphalt mixtures can be enhanced when various fibers are used,which results in the change of viscoelastic properties of mixtures.The creep test results show that the total strain and the permanent strain of asphalt mixtures during load-unload cycle can be significantly reduced,which results in the improvement of resistance to permanent deformation for asphalt mixtures containing various fiber additives.The Burgers model can be employed effectively to illustrate the rheological properties of fiber modified asphalt mixtures.展开更多
With the aim of studying the anti-rutting performance of Thiopave modified asphalt mixture applied to the upper layer of pavement, the strain-hardening creep model in ABAQUS finite element software was used to analyze...With the aim of studying the anti-rutting performance of Thiopave modified asphalt mixture applied to the upper layer of pavement, the strain-hardening creep model in ABAQUS finite element software was used to analyze the rutting under the condition of introducing temperature field. Compared with the calculation results of the rutting of ordinary asphalt pavement, it is found that Thiopave can improve the temperature sensitivity of asphalt mixture. With the increase of temperature, the rutting change of Thiopave modified asphalt pavement is smaller than that of ordinary asphalt. Thiopave also has a certain degree of improvement in the fatigue resistance of asphalt pavements, which can be applied to sections with high traffic volume in high temperature areas.展开更多
It was found that the cheap waste polyethylene film and polypropylenefilm are good modifying agents for the oxidized asphalt of high paraffin content,andthe polyvinyl chloride is not suited to be a modifying agent.The...It was found that the cheap waste polyethylene film and polypropylenefilm are good modifying agents for the oxidized asphalt of high paraffin content,andthe polyvinyl chloride is not suited to be a modifying agent.The modified asphalt isbetter than the original asphalt in high and low temperature properties.展开更多
基金The National Natural Science Foundation of China(No50578038)the PhDPrograms Foundation of Ministry of Education of China (No20050286008)
文摘The pavement performance of epoxy resin modified asphalt mixtures was investigated by the Marshall test, the indirect tensile test, the rutting test, the three-pointed bending test and the composite beam fatigue test. In comparison with the performance of epoxy resin modified asphalt mixtures, the performance of stone matrix asphalt mixtures （SMA10） was also investigated. The rutting test and composite beam fatigue test results show that the epoxy resin modified asphalt mixtures can improve permanent deformation and fatigue characteristics. They also show lower temperature susceptibility and greater resistance to moisture damage compared to the SMA10. Findings from the research indicate that the epoxy resin modified asphalt mixture provides an optional material for the pavement of long-span steel bridges in China due to profound performance and economic advantages.
基金Project(NCET-05-0656) supported by Education Ministry for the New Century Excellent Talents,China
文摘Shear resistance properties of the virgin bitumen and modified bitumen binders with Tafpack Super(TPS) modifier and SBS modified bitumen were discussed.Dynamic shear rheometer(DSR) was used to measure the laboratory creep data for these binders over a wide range of constant shear stresses at 20 ℃ to characterize the shear creep behaviors of all kinds of asphalt binders,and the rutting test system was used to investigate the permanent deformation of porous asphalt mixtures using the above bitumen binders for a fixed compressive stress.The shear strain rate and shear creep modulus were used to characterize the shear creep behavior of the TPS modified bitumen,and the rutting test results were used to show the consistency of porous asphalt mixtures with the bitumen binders.Results indicate that a distinction of shear creep strain can be made among different contents of TPS modified bitumen at the same stress level,where the shear creep strain-time response curve of the SBS modified bitumen binder is between the curves of the 8% TPS and 12% TPS modified bitumen binders.The shear strain rate and the shear creep modulus of the TPS modified bitumen binders are obtained to compare with those of the SBS modified bitumen binder which results in the same trend as the shear creep strain-time response curve.Permanent deformation results of all the porous asphalt mixtures from the rutting test show reasonable agreement with the findings of the shear strain rates and shear creep modulus over the range of shear stress levels.
基金Project(201703D321006)supported by the Shanxi Provincial Key Research and Development Project(Social Development),China。
文摘For the resource utilization of the solid waste coking sulfur paste and the improvement of performance of the asphalt mixture,a method for preparing modified asphalt mixture with coking sulfur paste modifier(CSPM)is herein proposed.Compared with the matrix asphalt mixture,the Marshall stability of the 30%CSPM modified asphalt mixture increased by 38.3%,the dynamic stability increased by nearly one time(reaching 1847.5 times/mm),the splitting strength ratio increased by 39.3%while the splitting tensile strength decreased by 11.7%.After curing,the performance of the CSPM modified asphalt mixture was further improved.The results show that CSPM improved the high temperature stability and water damage resistance of the asphalt mixture,and the low-temperature anti-cracking performance of that was slightly reduced.Chemical analysis of asphalt binders shows that a little sulfur reacted with asphalt to produce polysulfide compounds(R-Sx-R′),and a part of sulfur existed in the form of crystalline sulfur which was further increased after curing.The presence of crystalline sulfur as an inorganic filler is the key point for improving the high temperature stability and water resistance performance of modified asphalt mixture.
文摘Based on the analysis of the main failures discovered in pavement on steel deck plate and the demanding service condition of the pavement on steel deck, high-temperature rutting test, low-temperature bending test and controlled stress flexural fatigue test are used to study the performance of asphalt mixtures modified by epoxy resin including high-temperature stability, low-temperature cracking-resistance, and fatigue cracking-resistance, which are served to evaluate the modification effect of epoxy resin of different contents. With the addition of epoxy resin, all the three performances are improved greatly. However, when the amount of epoxy resin added is over a certain value, the modification effect will be stable with no extra benefit detected. Finally, in terms of the properties of the three respects, 20%, 30%, 30% are given separately as the proposal adding contents.
文摘In recent decades,modified asphalt materials have been used in enhancing the traffic load on the roads.The main objective of this paper is to explore the modifi cation effect of direct coal liquefaction residue(DCLR)on as-phalt binders and investigate the effectiveness of DCLR in improving the performance of asphalt road.This paper prepared modifi ed petroleum as-phalt under diff erent process conditions and tested its penetration,softening point and ductility index.Based on the experimental data,according to gray correlation degree,the performance for the asphalt was compared.The performance for the modified asphalt is simulated and predicted using poly-nomial functions.The modifi ed asphalt was analyzed by FT-IR,TGA,SEM and HPLC.The results show that the optimal process conditions for DCLR modifi ed asphalt are shear mixing time of 45 min,shear mixing tempera-ture of 150℃ and shear mixing rate of 4000 r/min.The predicted fit with the experimental data of 0.993 further demonstrates the effectiveness of the method.The characterization results show no significant chemical change between the DCLR and the asphalt.DCLR can significantly improve the high temperature performance and water stability of the asphalt,but it has little impact on its low temperature performance.
基金Projects (NCET-05-0656) supported by Education Ministry for the New Century Excellent Talents,China
文摘Rheological characteristics of fiber-modified asphalt mixture were investigated.Cellulous fiber,polyester fiber and mineral fiber were used as additives for asphalt mixture,and the dosages were 0.3%,0.3%,0.4%,respectively.Dynamic modulus test using superpave simple performance tester(SPT) was adopted to study the dynamic modulus and phase angle for the control mixture and fiber-modified ones at various temperatures and frequencies.Test results show that the rheological properties can be improved significantly by the addition of various fibers.The dynamic modulus increases with the increase of frequency,and the phase angle decreases with the increase of frequency.When various fibers are used,the dynamic modulus increases and phase angle decreases at each frequency.This indicates that the stiffness and the elastic portion of fiber-modified asphalt mixtures can be enhanced when various fibers are used,which results in the change of viscoelastic properties of mixtures.The creep test results show that the total strain and the permanent strain of asphalt mixtures during load-unload cycle can be significantly reduced,which results in the improvement of resistance to permanent deformation for asphalt mixtures containing various fiber additives.The Burgers model can be employed effectively to illustrate the rheological properties of fiber modified asphalt mixtures.
文摘With the aim of studying the anti-rutting performance of Thiopave modified asphalt mixture applied to the upper layer of pavement, the strain-hardening creep model in ABAQUS finite element software was used to analyze the rutting under the condition of introducing temperature field. Compared with the calculation results of the rutting of ordinary asphalt pavement, it is found that Thiopave can improve the temperature sensitivity of asphalt mixture. With the increase of temperature, the rutting change of Thiopave modified asphalt pavement is smaller than that of ordinary asphalt. Thiopave also has a certain degree of improvement in the fatigue resistance of asphalt pavements, which can be applied to sections with high traffic volume in high temperature areas.
文摘It was found that the cheap waste polyethylene film and polypropylenefilm are good modifying agents for the oxidized asphalt of high paraffin content,andthe polyvinyl chloride is not suited to be a modifying agent.The modified asphalt isbetter than the original asphalt in high and low temperature properties.
