The synthesis process of LiCo0.3Ni0.7O2 was investigated by FT-IR, mass spectroscopy, elemental analysis SEM, BET, TG/DTA and XRD in this paper. The results re- vealed that lithium and transition metal ions were trapp...The synthesis process of LiCo0.3Ni0.7O2 was investigated by FT-IR, mass spectroscopy, elemental analysis SEM, BET, TG/DTA and XRD in this paper. The results re- vealed that lithium and transition metal ions were trapped homogeneously on an atomic scale throughout the precursor Li2CO3, NiO and CoO are the intermediate products ob- tained after decomposition of the precursor and Li2CO3 un- dergoes direct reactions with NiO and CoO to form LiCo0.3Ni0.7O2. Moreover, the kinetics of formation of LiCo0.3Ni0.7O2 by citrate sol-gel method is faster than the case of the conventional solid-state reaction between lithium car- bonate and corresponding reactants. The single phase of LiCo0.3Ni0.7O2 was synthesized at temperature as low as 550℃. The discharge capacity of LiCo0.3Ni0.7O2 increases from 127 to 185 mAh/g as the calcination temperature in- creasing from 550 to 750℃. After 100 cycles, the discharge capacity of the sample calcined at 750℃ is 155 mAh/g. The electrochemical study shows that the LiCo0.3Ni0.7O2 has high discharge capacity and good cycling behavior for lithium ion batteries.展开更多
采用高温固相法烧结制备得到正极材料Li Ni0.5Co0.2Mn0.3O2,通过X射线衍射(XRD)、扫描电镜(SEM)以及循环伏安(CV)、交流阻抗(EIS)等电化学性能测试手段,探讨高温烧结工艺中不同锂源对材料结构、形貌及电化学性能的影响,结果表明,采用Li...采用高温固相法烧结制备得到正极材料Li Ni0.5Co0.2Mn0.3O2,通过X射线衍射(XRD)、扫描电镜(SEM)以及循环伏安(CV)、交流阻抗(EIS)等电化学性能测试手段,探讨高温烧结工艺中不同锂源对材料结构、形貌及电化学性能的影响,结果表明,采用Li OH作为锂源合成的材料与采用其他锂源相比,具有较好的层状结构和电化学性能.该材料在0.1C倍率下的首次充放电容量和库伦效率较高(172.7 m Ah/g,89.08%),在0.5C、1C倍率下循环50次后,材料的放电容量仍保持在144.5 m Ah/g和136.2 m Ah/g.展开更多
采用共沉淀-高温固相法合成正极材料LiNi0．7 Mn0．3 O 2,利用 X 射线衍射分析（XRD）表征其结构、扫描电子显微镜（SEM）表征其形貌、X 射线光电子能谱（XPS）表征其价态,最终确定了该材料最佳烧成温度为820℃.研究表明,该温度下合成的...采用共沉淀-高温固相法合成正极材料LiNi0．7 Mn0．3 O 2,利用 X 射线衍射分析（XRD）表征其结构、扫描电子显微镜（SEM）表征其形貌、X 射线光电子能谱（XPS）表征其价态,最终确定了该材料最佳烧成温度为820℃.研究表明,该温度下合成的 LiNi0．7 Mn0．3 O 2具有典型的α-NaFeO 2型层状结构,颗粒形貌呈类球形且分布均匀；XPS 数据表明,LiNi0．7 Mn0．3 O 2中的 Ni 主要以＋3价形态存在,Mn 主要以＋4价形态存在.室温条件下以0．2 C 倍率在2．75~4．35 V 的电压范围内充放电,首次放电比容量高达188．9 mAh/g,70次循环后容量保持率为95．2％.展开更多
NiO-La0.3Ce0.7O2-δ(LDC30) novel anode was investigated for IT-SOFCs(Intermediate Temperature-Solid Oxide Fuel Cells) with LaGaO3-based electrolyte. The results showed that LDC30 has a suitable chemical compatibility ...NiO-La0.3Ce0.7O2-δ(LDC30) novel anode was investigated for IT-SOFCs(Intermediate Temperature-Solid Oxide Fuel Cells) with LaGaO3-based electrolyte. The results showed that LDC30 has a suitable chemical compatibility with NiO and NiO-LDC30 has a good thermal expansion matching with LDC30 interlayer and LSGM(La0.8Sr0.2Ga0.8Mg0.2O3-δ) electrolyte, so NiO-LDC30/LDC30 was considered as a feasible and novel anode system. It was also shown that NiO content plays a key role on polarization performance and morphology of the anode. When the content of NiO was 60%(mass fraction), the polarization loss of anode was the lowest. Next we will optimize the porosity and sintering procedure to modify the microstructure and performance of the anode.展开更多
基金the EH.D Foundation of China(Grant No.20020610027)
文摘The synthesis process of LiCo0.3Ni0.7O2 was investigated by FT-IR, mass spectroscopy, elemental analysis SEM, BET, TG/DTA and XRD in this paper. The results re- vealed that lithium and transition metal ions were trapped homogeneously on an atomic scale throughout the precursor Li2CO3, NiO and CoO are the intermediate products ob- tained after decomposition of the precursor and Li2CO3 un- dergoes direct reactions with NiO and CoO to form LiCo0.3Ni0.7O2. Moreover, the kinetics of formation of LiCo0.3Ni0.7O2 by citrate sol-gel method is faster than the case of the conventional solid-state reaction between lithium car- bonate and corresponding reactants. The single phase of LiCo0.3Ni0.7O2 was synthesized at temperature as low as 550℃. The discharge capacity of LiCo0.3Ni0.7O2 increases from 127 to 185 mAh/g as the calcination temperature in- creasing from 550 to 750℃. After 100 cycles, the discharge capacity of the sample calcined at 750℃ is 155 mAh/g. The electrochemical study shows that the LiCo0.3Ni0.7O2 has high discharge capacity and good cycling behavior for lithium ion batteries.
文摘采用高温固相法烧结制备得到正极材料Li Ni0.5Co0.2Mn0.3O2,通过X射线衍射(XRD)、扫描电镜(SEM)以及循环伏安(CV)、交流阻抗(EIS)等电化学性能测试手段,探讨高温烧结工艺中不同锂源对材料结构、形貌及电化学性能的影响,结果表明,采用Li OH作为锂源合成的材料与采用其他锂源相比,具有较好的层状结构和电化学性能.该材料在0.1C倍率下的首次充放电容量和库伦效率较高(172.7 m Ah/g,89.08%),在0.5C、1C倍率下循环50次后,材料的放电容量仍保持在144.5 m Ah/g和136.2 m Ah/g.
文摘采用共沉淀-高温固相法合成正极材料LiNi0．7 Mn0．3 O 2,利用 X 射线衍射分析（XRD）表征其结构、扫描电子显微镜（SEM）表征其形貌、X 射线光电子能谱（XPS）表征其价态,最终确定了该材料最佳烧成温度为820℃.研究表明,该温度下合成的 LiNi0．7 Mn0．3 O 2具有典型的α-NaFeO 2型层状结构,颗粒形貌呈类球形且分布均匀；XPS 数据表明,LiNi0．7 Mn0．3 O 2中的 Ni 主要以＋3价形态存在,Mn 主要以＋4价形态存在.室温条件下以0．2 C 倍率在2．75~4．35 V 的电压范围内充放电,首次放电比容量高达188．9 mAh/g,70次循环后容量保持率为95．2％.
文摘NiO-La0.3Ce0.7O2-δ(LDC30) novel anode was investigated for IT-SOFCs(Intermediate Temperature-Solid Oxide Fuel Cells) with LaGaO3-based electrolyte. The results showed that LDC30 has a suitable chemical compatibility with NiO and NiO-LDC30 has a good thermal expansion matching with LDC30 interlayer and LSGM(La0.8Sr0.2Ga0.8Mg0.2O3-δ) electrolyte, so NiO-LDC30/LDC30 was considered as a feasible and novel anode system. It was also shown that NiO content plays a key role on polarization performance and morphology of the anode. When the content of NiO was 60%(mass fraction), the polarization loss of anode was the lowest. Next we will optimize the porosity and sintering procedure to modify the microstructure and performance of the anode.
