Research on level 2 control system of 100 tons LF furnace was carried out.According to the principle of energy conservation and principle of mass conservation,the LF temperature prediction model and the composition pr...Research on level 2 control system of 100 tons LF furnace was carried out.According to the principle of energy conservation and principle of mass conservation,the LF temperature prediction model and the composition prediction model were established.At the same time,the set value calculated by heating model and addition model could be sent to PLC.The results show that the technical indexes of LF furnace level 2 control system reach the demand and the system realizes automatic control.展开更多
This study was conducted to investigate the combined effects of elevated CO2 levels and cadmium (Cd) on the root morphological traits and Cd accumulation in Lolium multiflorum Lam.and Lolium perenne L.exposed to two C...This study was conducted to investigate the combined effects of elevated CO2 levels and cadmium (Cd) on the root morphological traits and Cd accumulation in Lolium multiflorum Lam.and Lolium perenne L.exposed to two CO2 levels (360 and 1000 μl/L) and three Cd levels (0,4,and 16 mg/L) under hydroponic conditions.The results show that elevated levels of CO2 increased shoot biomass more,compared to root biomass,but decreased Cd concentrations in all plant tissues.Cd exposure caused toxicity to both Lolium species,as shown by the restrictions of the root morphological parameters including root length,surface area,volume,and tip numbers.These parameters were significantly higher under elevated levels of CO2 than under ambient CO2,especially for the number of fine roots.The increases in magnitudes of those parameters triggered by elevated levels of CO2 under Cd stress were more than those under non-Cd stress,suggesting an ameliorated Cd stress under elevated levels of CO2.The total Cd uptake per pot,calculated on the basis of biomass,was significantly greater under elevated levels of CO2 than under ambient CO2.Ameliorated Cd toxicity,decreased Cd concentration,and altered root morphological traits in both Lolium species under elevated levels of CO2 may have implications in food safety and phytoremediation.展开更多
To establish the parsimonious model for blood glucose monitoring in patients with type 2 diabetes receiving oral hypoglycemic agent treatment. One hundred and fifty-nine adult Chinese type 2 diabetes patients were ran...To establish the parsimonious model for blood glucose monitoring in patients with type 2 diabetes receiving oral hypoglycemic agent treatment. One hundred and fifty-nine adult Chinese type 2 diabetes patients were randomized to receive rapid-acting or sustained-release gliclazide therapy for 12 weeks.展开更多
Concern about the biological hazards involved in microbiological research, especially research involving laboratory animals, has increased in recent years. Working in an animal biosafety level 2 facility （ABSL-2）, c...Concern about the biological hazards involved in microbiological research, especially research involving laboratory animals, has increased in recent years. Working in an animal biosafety level 2 facility （ABSL-2）, commonly used for research on infectious diseases, poses various biological hazards. Here, the regulations and standards related to laboratory biosafety in China are introduced, the potential biological hazards present in ABSL-2 facilities are analyzed, and a series of strategies to control the hazards are presented.展开更多
BACKGROUND MMP-2 also known as gelatinase A and MMP-7(matrilysin)are members of the zinc-dependent family of MMPs(Matrix metalloproteinase).MMP-2 and MMP-7 are remodeling enzymes that digest extracellular matrix;MMP-2...BACKGROUND MMP-2 also known as gelatinase A and MMP-7(matrilysin)are members of the zinc-dependent family of MMPs(Matrix metalloproteinase).MMP-2 and MMP-7 are remodeling enzymes that digest extracellular matrix;MMP-2 is extensively expressed during development and is upregulated at sites of tissue damage,inflammation,and in stromal cells of metastatic tumors.MMP-7 is expressed in the epithelial cells and in a variety of cancers including colon tumors.Plasma MMP-2 and MMP-7 levels were assessed before and after minimally invasive colorectal resection for cancer pathology.AIM To determine plasma MMP-2 and MMP-7 levels before and after minimally invasive colorectal resection for cancer pathology.METHODS Patients enrolled in a plasma bank for whom plasma was available were eligible.Plasma obtained from preoperative(Preop)and postoperative blood samples was used.Only colorectal cancer(CRC)patients who underwent elective minimally invasive cancer resection with preop,post-operative day(POD)1,3 and at least 1 late postop sample(POD 7-34)were included.Late samples were bundled into 7 d blocks(POD 7-13,14-20,etc.)and treated as single time points.Plasma MMP-2 and MMP-7 levels were determined via enzyme-linked immunosorbent assay in duplicate.RESULTS Total 88 minimally invasive CRC resection CRC patients were studied(right colectomy,37%;sigmoid,24%;and LAR/AR 18%).Cancer stages were:1,31%;2,30%;3,34%;and 4,5%.Mean Preop MMP-2 plasma level(ng/mL)was 179.3±40.9(n=88).Elevated mean levels were noted on POD1(214.3±51.2,n=87,P<0.001),POD3(258.0±63.9,n=80,P<0.001),POD7-13(229.9±62.3,n=65,P<0.001),POD 14-20(234.9±47.5,n=25,P<0.001),POD 21-27(237.0±63.5,n=17,P<0.001,)and POD 28-34(255.4±59.7,n=15,P<0.001).Mean Preop MMP-7 level was 3.9±1.9(n=88).No significant differences were noted on POD 1 or 3,however,significantly elevated levels were noted on POD 7-13(5.7±2.5,n=65,P<0.001),POD 14-20(5.9±2.5,n=25,P<0.001),POD 21-27(6.1±3.6,n=17,P=0.002)and on POD 28-34(6.8±3.3,n=15 P<0.001,)vs preop levels.CONCLUSION MMP-2 levels are elevated for 5 wk and MMP-7 levels elevated for weeks 2-6.The etiology of these changes in unclear,trauma and wound healing likely play a role.These changes may promote residual tumor growth and metastasis.展开更多
Many new steel plate processing facilities have been built in the past 10 years around the world with many more being planned for the future.This is especially true in developing countries such as China,India and Braz...Many new steel plate processing facilities have been built in the past 10 years around the world with many more being planned for the future.This is especially true in developing countries such as China,India and Brazil.Many of these facilities are plate mills with either one or two stands or a Steckel mill,typically only one stand designed for the production of structural plate steels.Unfortunately,there is a lack of understanding with both the mill builders of the world and the mill owners on the importance of properly matching up the available slab supply (either new as part of a new plate/Steckel mill complex or part of an already existing) with the desired end plate product mix.Many mill builders and owners around the world believe that you can take any slab of any dimension and make any plate dimension you want.While this is basically true with today’s Level 2 automation systems,it does not always result in optimum metallurgy/mechanical properties or productivity.This less than optimum condition results in mechanical property failures,shape issues,productivity losses and in general a less than desirable costly processing operation.It is important to the overall optimization of a steel processing facility that the proper slab dimensions be used to produce the proper final plate dimensions along with achieving the required mechanical properties.The critical nature of this selection will be dependent on the final plate thickness and overall mechanical property requirements.Proper mechanical property,shape and overall microstructure are heavily dependent on the ability to properly work the entire cross section of the slab through the rolling process.Many mechanical property,shape and microstructural issues are a result of improper working of the entire cross section during rolling.The ability for a given mill to properly work the entire cross section is dependent on proper slab selection (total reduction ratio) and a proper rolling schedule either generated manually by the operator or by the mills Level 2 automation system.The proper working and more importantly the true metallurgy of the slab being rolled does not occur until any dimensional rolling passes have been completed.In fact,dimensional rolling passes may create a negative situation that will have to be overcome in the remainder of the rolling schedule.This paper will discuss the importance of proper slab selection for a given plate dimension and final product.Examples and guidelines will be given related to proper slab selection for final plate dimensions and mechanical property requirements.展开更多
The vibrational levels and potential energy surface of a stable structure for S2O in the excited electronic states C^1A＇ were carried out with algebraic method. The vibrational spectra were obtained （with total quan...The vibrational levels and potential energy surface of a stable structure for S2O in the excited electronic states C^1A＇ were carried out with algebraic method. The vibrational spectra were obtained （with total quantum number v=20） by fitting 30 spectra data. The fitted rms（root mean square） error based on the Hamiltonian witb 9 parameters was 2.40 cm^-1. The dissociation energy and force constant were also determined by the analytical potential energy surface. The method is proved to be effective by comparing these results with the experimental data.展开更多
Production and destruction processes of carbon monoxide (CO) and ozone (O3) are examined in the light of increasing amount of atmospheric carbon dioxide (CO2). It is found that doubling of CO2 will increase the strato...Production and destruction processes of carbon monoxide (CO) and ozone (O3) are examined in the light of increasing amount of atmospheric carbon dioxide (CO2). It is found that doubling of CO2 will increase the stratospheric concentration of CO and will have positive effect on O3 concentration.展开更多
文摘Research on level 2 control system of 100 tons LF furnace was carried out.According to the principle of energy conservation and principle of mass conservation,the LF temperature prediction model and the composition prediction model were established.At the same time,the set value calculated by heating model and addition model could be sent to PLC.The results show that the technical indexes of LF furnace level 2 control system reach the demand and the system realizes automatic control.
基金Project supported by the Central Public Research Institute Basic Fund for Research and Development (2008-jxh-1),Agro-environmental Protection Institute,Ministry of Agriculture,China
文摘This study was conducted to investigate the combined effects of elevated CO2 levels and cadmium (Cd) on the root morphological traits and Cd accumulation in Lolium multiflorum Lam.and Lolium perenne L.exposed to two CO2 levels (360 and 1000 μl/L) and three Cd levels (0,4,and 16 mg/L) under hydroponic conditions.The results show that elevated levels of CO2 increased shoot biomass more,compared to root biomass,but decreased Cd concentrations in all plant tissues.Cd exposure caused toxicity to both Lolium species,as shown by the restrictions of the root morphological parameters including root length,surface area,volume,and tip numbers.These parameters were significantly higher under elevated levels of CO2 than under ambient CO2,especially for the number of fine roots.The increases in magnitudes of those parameters triggered by elevated levels of CO2 under Cd stress were more than those under non-Cd stress,suggesting an ameliorated Cd stress under elevated levels of CO2.The total Cd uptake per pot,calculated on the basis of biomass,was significantly greater under elevated levels of CO2 than under ambient CO2.Ameliorated Cd toxicity,decreased Cd concentration,and altered root morphological traits in both Lolium species under elevated levels of CO2 may have implications in food safety and phytoremediation.
文摘To establish the parsimonious model for blood glucose monitoring in patients with type 2 diabetes receiving oral hypoglycemic agent treatment. One hundred and fifty-nine adult Chinese type 2 diabetes patients were randomized to receive rapid-acting or sustained-release gliclazide therapy for 12 weeks.
基金supported by the National Science and Technology Major Projects of Infectious Disease(2012ZX10004-404)
文摘Concern about the biological hazards involved in microbiological research, especially research involving laboratory animals, has increased in recent years. Working in an animal biosafety level 2 facility （ABSL-2）, commonly used for research on infectious diseases, poses various biological hazards. Here, the regulations and standards related to laboratory biosafety in China are introduced, the potential biological hazards present in ABSL-2 facilities are analyzed, and a series of strategies to control the hazards are presented.
文摘BACKGROUND MMP-2 also known as gelatinase A and MMP-7(matrilysin)are members of the zinc-dependent family of MMPs(Matrix metalloproteinase).MMP-2 and MMP-7 are remodeling enzymes that digest extracellular matrix;MMP-2 is extensively expressed during development and is upregulated at sites of tissue damage,inflammation,and in stromal cells of metastatic tumors.MMP-7 is expressed in the epithelial cells and in a variety of cancers including colon tumors.Plasma MMP-2 and MMP-7 levels were assessed before and after minimally invasive colorectal resection for cancer pathology.AIM To determine plasma MMP-2 and MMP-7 levels before and after minimally invasive colorectal resection for cancer pathology.METHODS Patients enrolled in a plasma bank for whom plasma was available were eligible.Plasma obtained from preoperative(Preop)and postoperative blood samples was used.Only colorectal cancer(CRC)patients who underwent elective minimally invasive cancer resection with preop,post-operative day(POD)1,3 and at least 1 late postop sample(POD 7-34)were included.Late samples were bundled into 7 d blocks(POD 7-13,14-20,etc.)and treated as single time points.Plasma MMP-2 and MMP-7 levels were determined via enzyme-linked immunosorbent assay in duplicate.RESULTS Total 88 minimally invasive CRC resection CRC patients were studied(right colectomy,37%;sigmoid,24%;and LAR/AR 18%).Cancer stages were:1,31%;2,30%;3,34%;and 4,5%.Mean Preop MMP-2 plasma level(ng/mL)was 179.3±40.9(n=88).Elevated mean levels were noted on POD1(214.3±51.2,n=87,P<0.001),POD3(258.0±63.9,n=80,P<0.001),POD7-13(229.9±62.3,n=65,P<0.001),POD 14-20(234.9±47.5,n=25,P<0.001),POD 21-27(237.0±63.5,n=17,P<0.001,)and POD 28-34(255.4±59.7,n=15,P<0.001).Mean Preop MMP-7 level was 3.9±1.9(n=88).No significant differences were noted on POD 1 or 3,however,significantly elevated levels were noted on POD 7-13(5.7±2.5,n=65,P<0.001),POD 14-20(5.9±2.5,n=25,P<0.001),POD 21-27(6.1±3.6,n=17,P=0.002)and on POD 28-34(6.8±3.3,n=15 P<0.001,)vs preop levels.CONCLUSION MMP-2 levels are elevated for 5 wk and MMP-7 levels elevated for weeks 2-6.The etiology of these changes in unclear,trauma and wound healing likely play a role.These changes may promote residual tumor growth and metastasis.
文摘Many new steel plate processing facilities have been built in the past 10 years around the world with many more being planned for the future.This is especially true in developing countries such as China,India and Brazil.Many of these facilities are plate mills with either one or two stands or a Steckel mill,typically only one stand designed for the production of structural plate steels.Unfortunately,there is a lack of understanding with both the mill builders of the world and the mill owners on the importance of properly matching up the available slab supply (either new as part of a new plate/Steckel mill complex or part of an already existing) with the desired end plate product mix.Many mill builders and owners around the world believe that you can take any slab of any dimension and make any plate dimension you want.While this is basically true with today’s Level 2 automation systems,it does not always result in optimum metallurgy/mechanical properties or productivity.This less than optimum condition results in mechanical property failures,shape issues,productivity losses and in general a less than desirable costly processing operation.It is important to the overall optimization of a steel processing facility that the proper slab dimensions be used to produce the proper final plate dimensions along with achieving the required mechanical properties.The critical nature of this selection will be dependent on the final plate thickness and overall mechanical property requirements.Proper mechanical property,shape and overall microstructure are heavily dependent on the ability to properly work the entire cross section of the slab through the rolling process.Many mechanical property,shape and microstructural issues are a result of improper working of the entire cross section during rolling.The ability for a given mill to properly work the entire cross section is dependent on proper slab selection (total reduction ratio) and a proper rolling schedule either generated manually by the operator or by the mills Level 2 automation system.The proper working and more importantly the true metallurgy of the slab being rolled does not occur until any dimensional rolling passes have been completed.In fact,dimensional rolling passes may create a negative situation that will have to be overcome in the remainder of the rolling schedule.This paper will discuss the importance of proper slab selection for a given plate dimension and final product.Examples and guidelines will be given related to proper slab selection for final plate dimensions and mechanical property requirements.
基金This work Was supported by the National Natural Science Foundation of China（NSFCNo.10474050）.
文摘The vibrational levels and potential energy surface of a stable structure for S2O in the excited electronic states C^1A＇ were carried out with algebraic method. The vibrational spectra were obtained （with total quantum number v=20） by fitting 30 spectra data. The fitted rms（root mean square） error based on the Hamiltonian witb 9 parameters was 2.40 cm^-1. The dissociation energy and force constant were also determined by the analytical potential energy surface. The method is proved to be effective by comparing these results with the experimental data.
文摘Production and destruction processes of carbon monoxide (CO) and ozone (O3) are examined in the light of increasing amount of atmospheric carbon dioxide (CO2). It is found that doubling of CO2 will increase the stratospheric concentration of CO and will have positive effect on O3 concentration.
