Lanthanide has attracted much attention in the field of optical communications in recent years. Some property analyses on optical waveguide of Nd doped crystal Nd x Y 1-x A1 3(BO 3) 4 and Nd∶MgO∶LiNbO 3 are made in ...Lanthanide has attracted much attention in the field of optical communications in recent years. Some property analyses on optical waveguide of Nd doped crystal Nd x Y 1-x A1 3(BO 3) 4 and Nd∶MgO∶LiNbO 3 are made in this paper, followed by introduction of the methods of experimentation and theoretical calculation for the planar optical waveguides. The refractive index profiles of the optical waveguides are analyzed. The above work offers useful information for study on new type materials for optical communications.展开更多
Emission enhancement at 2.7 μm is observed in Er^3＋/Pr^3＋--codoped germanate glasses when pumped by a 980-nm laser diode. Significant reductions in 1.5-μm emission and upeonversion intensity indicate efficient ene...Emission enhancement at 2.7 μm is observed in Er^3＋/Pr^3＋--codoped germanate glasses when pumped by a 980-nm laser diode. Significant reductions in 1.5-μm emission and upeonversion intensity indicate efficient energy transfer between Er^3＋ and Pr^3＋; the energy transfer efficiency is as high as 77.4%. The mechanisms of energy transfer are discussed in detail. The calculated emission cross-section of Er^3＋/Pr^3＋- codoped germanate glass is 8.44× 10 ^-21 cm^2, which suggests that Er^3＋/Pr^3＋-codoped germanate glass can be used to achieve efficient 2.7-μm emission.展开更多
The possible ways and progress of infrared or red laser pumped green and blue laser emissions from a single solid state material doped by rare earth ions are outlined. The green and blue lasers realized from infrared ...The possible ways and progress of infrared or red laser pumped green and blue laser emissions from a single solid state material doped by rare earth ions are outlined. The green and blue lasers realized from infrared laser pumped rare earth doped nonlinear laser crystals by means of self frequency conversion and from infrared laser pumped rare earth doped bulk, fiber and microsphere materials by means of frequency upconversion are introduced in detail. Other kinds of devices and methods are also compared. The typical nonlinear laser crystals such as YAl 3(BO 3) 4, GdAl 3(BO 3) 4, YCa 4O(BO 3) 3 , GdCa 4O(BO 3) 3, and the typical upconversion fluoride fibers are compared and analyzed. The major problems remaining to be solved and the developing trends in the area are also discussed.展开更多
To enhance the adhesion of ceramic coatings in turbine blade Thermal Barrier Coatings(TBCs)systems,Laser Surface Texturing(LST)was employed to create microstructures on the metal bond coat.The bonding conditions and f...To enhance the adhesion of ceramic coatings in turbine blade Thermal Barrier Coatings(TBCs)systems,Laser Surface Texturing(LST)was employed to create microstructures on the metal bond coat.The bonding conditions and failure mechanisms of the ceramic coatings within these microstructures were thoroughly investigated.Femtosecond laser technology was used to fabricate three types of high-quality microstructure grooves:linear,sine wave,and grid patterns.These grooves exhibit uniform morphology,well-defined edges,and smooth inner walls.After ceramic coating deposition,columnar crystal structures grew perpendicularly along the groove walls,completely filling the microstructures and forming an arched support structure that significantly enhances mechanical interlocking and adhesion.Among the different microstructures,grid patterns demonstrated the best adhesion performance.In scratch tests,grid-patterned microstructures exhibited only localized small block spalling under high load conditions,avoiding large-scale delamination.This superior performance is attributed to the ability of grid pattern to effectively distribute stress in multiple directions and prevent crack propagation.By reducing stress concentration and enhancing mechanical interlocking points,grid-patterned microstructures also showed excellent resistance to spallation during thermal cycling,markedly improving the thermal resistance and adhesion of coating.展开更多
The 1.55μm laser technology is widely applied in military,information communication,biomedicine and other fields.With the deepening development of these application areas,the demand for novel 1.55μm laser gain media...The 1.55μm laser technology is widely applied in military,information communication,biomedicine and other fields.With the deepening development of these application areas,the demand for novel 1.55μm laser gain media is becoming increasingly urgent.This study reports a novel Yb^(3+),Er^(3+)co-doped KBa_(0.94)Ca_(0.06)Y(MoO_(4))_(3) (KBCYM)crystal.In this crystal,Yb^(3+)serves as a sensitizer,significantly enhancing the emission intensity of Er^(3+)in both visible and near-infrared bands.Notably,when the concentration of Yb^(3+)reaches 6 mol%,the emission intensity peaks at 1.55μm.Optical cross-section calculations reveal that the crystal exhibits a low laser pumping threshold at this concentration,demonstrating its potential as a laser gain medium.However,the crystal inevitably generates thermal effects during operation,which may adversely affect its performance.Therefore,real-time monitoring of the operating temperature is crucial.The thermal stability of the crystal was evaluated by measuring the temperature dependence of its luminescence intensity in the near-infrared band.Remarkably,even when the temperature rises to 553 K,the emission intensity at 1.55μm only decreases by 10.9%.Additionally,the temperature sensing performance was evaluated using fluorescence intensity ratio techniques,yielding absolute and relative sensitivities of 0.00981 K^(-1)at 453 K and 1.32%/K at 303 K,respectively,highlighting its potential for optical temperature sensing.Finally,through leveraging the unique properties of Yb^(3+),Er^(3+):KBCYM crystals,we successfully developed 1.55μm luminescent optical devices with practical applications.These devices not only exhibit efficient luminescent performance,but also possess a self-temperature measu rement functio n,opening up new avenues for the further development of laser technology.展开更多
A 10 J, 4o us XeCl laser interaction with LY12 aluminum and optical glass K9 targets is reported. The properties of laser-produced plasma (LPP) are analyzed. As a result, some parameters such as plasma ignition thresh...A 10 J, 4o us XeCl laser interaction with LY12 aluminum and optical glass K9 targets is reported. The properties of laser-produced plasma (LPP) are analyzed. As a result, some parameters such as plasma ignition threshold and plasma plume expansion velocity are obtained. Also, Laser induced pulse on irradiated targets are given.展开更多
B4C, SiC and C, Cu functionally graded-materials (FGMs) have been developed by plasma spraying and hot pressing. Their high-heat flux properties have been investigated by high energy laser and electron beam for the si...B4C, SiC and C, Cu functionally graded-materials (FGMs) have been developed by plasma spraying and hot pressing. Their high-heat flux properties have been investigated by high energy laser and electron beam for the simulation of plasma disruption process of the future fusion reactors, And a study on eroded products of B4C/Cu FGM under transient thermal load of electron beam was performed. In the experiment, SEM and EDS analysis indicated that B4C and SiC were decomposed, carbon was preferentially evaporated under high thermal load, and a part of Si and Cu were melted, in addition, the splash of melted metal and the particle emission of brittle destruction were also found. Different erosive behaviors of carbon-based materials (CBMs) caused by laser and electron beam were also discussed.展开更多
Changes of surface morphology following XeCI excimer laser irradiation were investigated for three engineering ceramic materials (Al2O3, Al2O3-SiC nanocomposite and Si3N4). Al2O3 and AI2O3-SiC nanocomposite samples ex...Changes of surface morphology following XeCI excimer laser irradiation were investigated for three engineering ceramic materials (Al2O3, Al2O3-SiC nanocomposite and Si3N4). Al2O3 and AI2O3-SiC nanocomposite samples exhibit a smooth rapid melt layer on the surface, and the formation of the metastabfe γ-Al2Oa was observed. A silicon-rich layer on the surface was formed after laser irradiation of Si3N4. The toughness K1c of the materials was measured by the indentation fracture method. After laser irradiation, the toughness of Al2O3, Al2O3-SiC nanocomposite and Si3N4 was improved to various degrees: Al2O3-SiC nanocomposite, 60% (max.); AI203, 40% (max.); Si3N4, 12% (max.).展开更多
Dy：Lu2O3 was grown by the float-zone （Fz） method. According to the absorption spectrum, the Judd-Ofelt （JO） parameters Ω2, Ω4, and Ω6 were calculated to be 4.86 × 10-20 cm2, 2.02 × 10-20 cm2, and 1.7...Dy：Lu2O3 was grown by the float-zone （Fz） method. According to the absorption spectrum, the Judd-Ofelt （JO） parameters Ω2, Ω4, and Ω6 were calculated to be 4.86 × 10-20 cm2, 2.02 × 10-20 cm2, and 1.76 ×10-20 cm2, respectively. The emission cross-section at 574 nm corresponding to the 4F9/2 →6H13/2 transition was calculated to be 0.53 ×10 20 cm2. The yellow （4F9/2 →6H13/2 transition） to blue （4F9/2 →6H15/2 transition） intensity ratio ranges up to 12.9. The fluorescence lifetime of the 4F9/2 energy level was measured to be 112.1 μs. These results reveal that Dy：Lu2O3 is a promising material for use in yellow lasers.展开更多
Transparent polycrystaUine neodymiumdoped yttrium aluminum garnet ceramics （Nd：YAG） with better chemical stability, excellent optical and high temperature mechanical property is becoming a new laser host material. ...Transparent polycrystaUine neodymiumdoped yttrium aluminum garnet ceramics （Nd：YAG） with better chemical stability, excellent optical and high temperature mechanical property is becoming a new laser host material. The Nd：YAG precursor powders with loosely dispersed, slightly agglomerated and YAG cubic crystal phase were synthesized at 1100 ℃ by the co-precipitation method combined with the reverse strike,展开更多
We demonstrate the spectroscopic and laser performance before and after 100 Mrad gamma-ray irradiation on an Er,Pr：GYSGG crystal grown by the Czochralski method. The additional absorption of Er,Pr：GYSGG crystal is c...We demonstrate the spectroscopic and laser performance before and after 100 Mrad gamma-ray irradiation on an Er,Pr：GYSGG crystal grown by the Czochralski method. The additional absorption of Er,Pr：GYSGG crystal is close to zero in the 968 nm pumping and 2.7-3 μm laser wavelength regions. The lifetimes of the upper and lower levels show faint decreases after gamma-ray irradiation. The maximum output powers of 542 and 526 mW with the slope efficiencies of 17.7% and 17.0% are obtained, respectively, on the GYSGG/Er,Pr：GYSGG composite crystal before and after the gammaray irradiation. These results suggest that Er,Pr：GYSGG crystal as a laser gain medium possesses a distinguished antiradiation ability for application in space and radiant environments.展开更多
The coupling strengthening principle of the double physical effect of plasma shock−cavitation was proposed,and the rationality of the cavitation effect in pulsed laser shock treatment under liquid−confined conditions ...The coupling strengthening principle of the double physical effect of plasma shock−cavitation was proposed,and the rationality of the cavitation effect in pulsed laser shock treatment under liquid−confined conditions needs to be confirmed urgently.The XRD testing method and 304 stainless steel,which is easy to obtain diffraction peaks,were selected to quantitatively detect and characterize the residual stress distribution in the action area of a single pulse laser beam.The test results and literature analysis show that the different process conditions of laser shock processing bring about different strength matching of the two stress effects of plasma shock and cavitation,and the main source of stress effect of femtosecond laser shock without coating is the cavitation effect.The actual effects of the laser pulse width and other process parameters such as the absorption layer and the constraint layer affect or determine the material modification principle of the pulsed laser surface treatment.展开更多
The 4-at.% Tm：Sc_2SiO_5 （Tm：SSO） crystal is successfully obtained by the Czochralski method. The optical properties and thermal conductivity of the crystal are investigated. The broad continuous wave（CW） laser o...The 4-at.% Tm：Sc_2SiO_5 （Tm：SSO） crystal is successfully obtained by the Czochralski method. The optical properties and thermal conductivity of the crystal are investigated. The broad continuous wave（CW） laser output of（100）-cut Tm：SSO with the dimensions of 3 mm×3 mm×3 mm under laser diode（LD）-pumping is realized. The full width at half maximum（FWHM） of the laser emitting reaches up to 21 nm. The laser threshold of Tm：SSO is measured to be 0.43 W. Efficient diode-pumped CW laser performance of Tm：SSO is demonstrated with a slope efficiency of 25.9% and maximum output power of 934 mW.展开更多
A CaF2-CeF3 disordered crystal containing 1.06% of Er^3＋ ions was grown by the temperature gradient technique.Optical absorption and emission spectra recorded at room temperature and at 10 K, luminescence decay curve...A CaF2-CeF3 disordered crystal containing 1.06% of Er^3＋ ions was grown by the temperature gradient technique.Optical absorption and emission spectra recorded at room temperature and at 10 K, luminescence decay curve recorded at room temperature, and extended x-ray-absorption fine structure spectra were analyzed with an intention to assess the laser potential related to the ^4I13/2→^4I15/2 transition of Er^3＋. In addition, the thermal diffusivity of the crystal was measured at room temperature. The analysis of room-temperature spectra revealed that the ^4I13/2 emission is long-lived with a radiative lifetime value of 5.5 ms, peak emission cross section of 0.73 × 10^-20 cm^2, and large spectral width pointing at the tunability of the emission wavelength in the region stretching from approximately 1480 nm to 1630 nm. The energies of the crystal field components for the ground and excited multiplets determined from low-temperature absorption and emission spectra made it possible to predict successfully the spectral position and shape of the room-temperature ^4I13/2→^4I15/2 emission band. Based on the correlation of the optical spectra and dynamics of the luminescence decay, it was concluded that in contrast to Yb^3＋ ions in heavily doped CaF2 erbium ions in the CaF2-CeF3 crystal reside in numerous sites with dissimilar relaxation rates.展开更多
Spectroscopic and fluorescence properties of Nd 3＋ ions in sodium fluoroborate（SFB） glasses were prepared and characterized through optical absorption,emission and decay measurements.The energy level analysis was c...Spectroscopic and fluorescence properties of Nd 3＋ ions in sodium fluoroborate（SFB） glasses were prepared and characterized through optical absorption,emission and decay measurements.The energy level analysis was carried out using free-ion Hamiltonian model.Experimental oscillator strengths were determined by measuring the area encompassed by the absorption peaks recorded for 1.0 mol.% Nd 3＋-doped glasses.The Judd-Ofelt parameters（2,4,6） were used to evaluate the laser characteristic parameters such as radiative transition probability（A R）,radiative decay time（τ R）,fluorescence branching ratio（β R） and stimulated emission cross-section（σ e） for the 4 F 3/2 metastable state.The fluorescence spectra for different concentrations of Nd 3＋ ions were recorded by exciting the samples at 514.5 nm Ar ＋ ion laser.展开更多
A Ca9Yb（VO4）7 crystal with dimensions of Φ23 mm×35 mm was grown successfully by Czochralski method. Its thermal conductivity was 1.06 W/（m？K） at room temperature. The absorption cross-sections at 980 nm wer...A Ca9Yb（VO4）7 crystal with dimensions of Φ23 mm×35 mm was grown successfully by Czochralski method. Its thermal conductivity was 1.06 W/（m？K） at room temperature. The absorption cross-sections at 980 nm were 1.80×10–20 cm2 and 1.28×10–20 cm2 for π- and σ- polarizations, respectively, with a full-width at half-maximum of 34 nm. The crystal had a broad emission at around 1025 nm with a full-width at half-maximum of 67 nm for π- polarization and 70 nm for σ- polarization. The emission cross-sections of the crystal were calculated by using reciprocity method and Füchtbauer-Ladenburg formula. The emission cross-sections at 1025 nm were 3.57×10–20 cm–2 and 1.91×10–20 cm–2 for π- and σ- polarization, respectively. The fluorescence lifetime was 332 μs. The results indicated that the crystal is a promising femtosecond and tunable laser material.展开更多
Lead halide perovskites have attracted considerable attention as potential candidates for high-performance nano/microlasers,owing to their outstanding optical properties.However,the further development of perovskite m...Lead halide perovskites have attracted considerable attention as potential candidates for high-performance nano/microlasers,owing to their outstanding optical properties.However,the further development of perovskite microlaser arrays(especially based on polycrystalline thin films)produced by the conventional processing techniques is hindered by the chemical instability and surface roughness of the perovskite structures.Herein,we demonstrate a laser patterning of large-scale,highly crystalline perovskite single-crystal films to fabricate reproducible perovskite single-crystal-based microlaser arrays.Perovskite thin films were directly ablated by femtosecond-laser in multiple low-power cycles at a minimum machining line width of approximately 300 nm to realize high-precision,chemically clean,and repeatable fabrication of microdisk arrays.The surface impurities generated during the process can be washed away to avoid external optical loss due to the robustness of the single-crystal film.Moreover,the high-quality,large-sized perovskite single-crystal films can significantly improve the quality of microcavities,thereby realizing a perovskite microdisk laser with narrow linewidth(0.09 nm)and low threshold(5.1µJ/cm2).Benefiting from the novel laser patterning method and the large-sized perovskite single-crystal films,a high power and high color purity laser display with single-mode microlasers as pixels was successfully fabricated.Thus,this study may offer a potential platform for mass-scale and reproducible fabrication of microlaser arrays,and further facilitate the development of highly integrated applications based on perovskite materials.展开更多
The use of a CO2 laser system for fabrication of microfluidic chip on polymethyl methacrylate （PMMA） is presented to reduce fabrication cost and time of chip. The grooving process of the laser system and a model for...The use of a CO2 laser system for fabrication of microfluidic chip on polymethyl methacrylate （PMMA） is presented to reduce fabrication cost and time of chip. The grooving process of the laser system and a model for the depth of microchannels are investigated. The relations between the depth of laser-cut channels and the laser beam power, velocity or the number of passes of the beam along the same channel are evaluated. In the experiments, the laser beam power varies from 0 to 50 W, the laser beam scanning velocity varies from 0 to 1 000 mm/s and the passes vary in the range of 1 to 10 times. Based on the principle of conservation of energy, the influence of the laser beam velocity, the laser power and the number of groove passes are examine. Considering the grooving interval energy loss, a modified mathematical model has been obtained and experimental data show good agreement with the theoretical model. This approach provides a simple way of predicting groove depths. The system provides a cost alternative of the other methods and it is especially useful on research work of rnicrofluidic prototyping due to the short cycle time of production.展开更多
Sn_(1−x)Er_(x)O_(2)(x=0%,8%,16%,24%)micro/nanofibers were prepared by electrospinning combined with heat treatment using erbium nitrate,stannous chloride and polyvinylpyrrolidone(PVP)as raw materials.The target produc...Sn_(1−x)Er_(x)O_(2)(x=0%,8%,16%,24%)micro/nanofibers were prepared by electrospinning combined with heat treatment using erbium nitrate,stannous chloride and polyvinylpyrrolidone(PVP)as raw materials.The target products were characterized by thermogravimetric analyzer,X-ray diffrotometer,fourier transform infrared spectrometer,scanning electron microscope,spectrophotometer and infrared emissivity tester,and the effects of Er^(3+)doping on its infrared and laser emissivity were studied.At the same time,the Sn_(1−x)Er_(x)O_(2)(x=0%,16%)doping models were constructed based on the first principles of density functional theory,and the related optoelectronic properties such as their energy band structure,density of states,reflectivity and dielectric constant were analyzed,and further explained the mechanism of Er^(3+)doping on SnO_(2)infrared emissivity and laser absorption from the point of electronic structure.The results showed that after calcination at 600℃,single rutile type SnO_(2)was formed,and the crystal structure was not changed by doping Er^(3+).The calcined products showed good fiber morphology,and the average fiber diameter was 402 nm.The infrared emissivity and resistivity of the samples both decreased first and then increased with the increase of Er^(3+)doping amount.When x=16%,the infrared emis-sivity of the sample was at least 0.71;and Er^(3+)doping can effectively reduce the reflectivity of SnO_(2)at 1.06μm and 1.55μm,when x=16%,its reflectivity at 1.06μm and 1.55μm are 50.5%and 40%,respectively,when x=24%,the reflectivity at 1.06μm and 1.55μm wavelengths are 47.3%and 42.1%,respectively.At the same time,the change of carrier concentration and electron transition before and after Er^(3+)doping were described by first-principle calculation,and the regulation mechanism of infrared emissivity and laser reflectivity was explained.This study provides a certain experimental and theoretical basis for the development of a single-type,light-weight and easily prepared infrared and laser compatible-stealth material.展开更多
substitutes tion, high loosely dis Neodymium doped-yttrium aluminum garnet （Nd ： YAG） transparent polycrystalline ceramics already become of single crystals because they are provided with easy fabrication, low cost...substitutes tion, high loosely dis Neodymium doped-yttrium aluminum garnet （Nd ： YAG） transparent polycrystalline ceramics already become of single crystals because they are provided with easy fabrication, low cost, large size, highly doped concentraheat conductivity, mass fabrication, multi-layers and multi-filnctions. The Nd：YAG precursor powders with persed , slightly agglomerated, super fine and YAG cubic crystal phase were synthesized at 1100 ℃ by the homogeneous precipitation method, using Nd2O3, Y2O3, Al（NO3）3·9H2O and urea as raw materials, （NH4）2SO4 as electrical stabilizer, TEOS as sintering additive. The Nd：YAG transparent ceramics were prepared after being vacuum sintered at 1700 ℃ for 5 h. The Nd：YAG ceramic materials were characterized by the TG-DTA, XRD, FT-IR, TEM, FEG-ESEM and FT-PL. The results show that the crystallization temperature of YAG is 850 ℃ and the intermediate crystal phase YAP forming during the heat treatment transforms to YAG cubic crystal phase at 1050 ℃. The lasing wavelength of （Nd0.01 Y0.99）3Al5O12 transparent ceramics is 1.065 μm and there exists a slight red-shift compared to the single crystal with the same chemical composition. The optical transmittance is 45 % in the visible light and 58 % in the near infrared light and the optical transmittance descends with the decreasing the wavelength.展开更多
文摘Lanthanide has attracted much attention in the field of optical communications in recent years. Some property analyses on optical waveguide of Nd doped crystal Nd x Y 1-x A1 3(BO 3) 4 and Nd∶MgO∶LiNbO 3 are made in this paper, followed by introduction of the methods of experimentation and theoretical calculation for the planar optical waveguides. The refractive index profiles of the optical waveguides are analyzed. The above work offers useful information for study on new type materials for optical communications.
基金supported by the National Natural Science Foundation of China(Nos.51172252 and 61177083)
文摘Emission enhancement at 2.7 μm is observed in Er^3＋/Pr^3＋--codoped germanate glasses when pumped by a 980-nm laser diode. Significant reductions in 1.5-μm emission and upeonversion intensity indicate efficient energy transfer between Er^3＋ and Pr^3＋; the energy transfer efficiency is as high as 77.4%. The mechanisms of energy transfer are discussed in detail. The calculated emission cross-section of Er^3＋/Pr^3＋- codoped germanate glass is 8.44× 10 ^-21 cm^2, which suggests that Er^3＋/Pr^3＋-codoped germanate glass can be used to achieve efficient 2.7-μm emission.
文摘The possible ways and progress of infrared or red laser pumped green and blue laser emissions from a single solid state material doped by rare earth ions are outlined. The green and blue lasers realized from infrared laser pumped rare earth doped nonlinear laser crystals by means of self frequency conversion and from infrared laser pumped rare earth doped bulk, fiber and microsphere materials by means of frequency upconversion are introduced in detail. Other kinds of devices and methods are also compared. The typical nonlinear laser crystals such as YAl 3(BO 3) 4, GdAl 3(BO 3) 4, YCa 4O(BO 3) 3 , GdCa 4O(BO 3) 3, and the typical upconversion fluoride fibers are compared and analyzed. The major problems remaining to be solved and the developing trends in the area are also discussed.
基金supported by the National Science and Technology Major Project,China(No.J2019-VII-0013-0153)the Sichuan Science and Technology Program,China(Nos.2021ZDZX0001 and 2021ZDZX0002)。
文摘To enhance the adhesion of ceramic coatings in turbine blade Thermal Barrier Coatings(TBCs)systems,Laser Surface Texturing(LST)was employed to create microstructures on the metal bond coat.The bonding conditions and failure mechanisms of the ceramic coatings within these microstructures were thoroughly investigated.Femtosecond laser technology was used to fabricate three types of high-quality microstructure grooves:linear,sine wave,and grid patterns.These grooves exhibit uniform morphology,well-defined edges,and smooth inner walls.After ceramic coating deposition,columnar crystal structures grew perpendicularly along the groove walls,completely filling the microstructures and forming an arched support structure that significantly enhances mechanical interlocking and adhesion.Among the different microstructures,grid patterns demonstrated the best adhesion performance.In scratch tests,grid-patterned microstructures exhibited only localized small block spalling under high load conditions,avoiding large-scale delamination.This superior performance is attributed to the ability of grid pattern to effectively distribute stress in multiple directions and prevent crack propagation.By reducing stress concentration and enhancing mechanical interlocking points,grid-patterned microstructures also showed excellent resistance to spallation during thermal cycling,markedly improving the thermal resistance and adhesion of coating.
基金Project supported by Jilin Provincial Department of Education(JJKH20230821KJ,JJKH20230822KJ,JJKH20230823KJ,JJKH20240930KJ,20240101107JC)。
文摘The 1.55μm laser technology is widely applied in military,information communication,biomedicine and other fields.With the deepening development of these application areas,the demand for novel 1.55μm laser gain media is becoming increasingly urgent.This study reports a novel Yb^(3+),Er^(3+)co-doped KBa_(0.94)Ca_(0.06)Y(MoO_(4))_(3) (KBCYM)crystal.In this crystal,Yb^(3+)serves as a sensitizer,significantly enhancing the emission intensity of Er^(3+)in both visible and near-infrared bands.Notably,when the concentration of Yb^(3+)reaches 6 mol%,the emission intensity peaks at 1.55μm.Optical cross-section calculations reveal that the crystal exhibits a low laser pumping threshold at this concentration,demonstrating its potential as a laser gain medium.However,the crystal inevitably generates thermal effects during operation,which may adversely affect its performance.Therefore,real-time monitoring of the operating temperature is crucial.The thermal stability of the crystal was evaluated by measuring the temperature dependence of its luminescence intensity in the near-infrared band.Remarkably,even when the temperature rises to 553 K,the emission intensity at 1.55μm only decreases by 10.9%.Additionally,the temperature sensing performance was evaluated using fluorescence intensity ratio techniques,yielding absolute and relative sensitivities of 0.00981 K^(-1)at 453 K and 1.32%/K at 303 K,respectively,highlighting its potential for optical temperature sensing.Finally,through leveraging the unique properties of Yb^(3+),Er^(3+):KBCYM crystals,we successfully developed 1.55μm luminescent optical devices with practical applications.These devices not only exhibit efficient luminescent performance,but also possess a self-temperature measu rement functio n,opening up new avenues for the further development of laser technology.
文摘A 10 J, 4o us XeCl laser interaction with LY12 aluminum and optical glass K9 targets is reported. The properties of laser-produced plasma (LPP) are analyzed. As a result, some parameters such as plasma ignition threshold and plasma plume expansion velocity are obtained. Also, Laser induced pulse on irradiated targets are given.
文摘B4C, SiC and C, Cu functionally graded-materials (FGMs) have been developed by plasma spraying and hot pressing. Their high-heat flux properties have been investigated by high energy laser and electron beam for the simulation of plasma disruption process of the future fusion reactors, And a study on eroded products of B4C/Cu FGM under transient thermal load of electron beam was performed. In the experiment, SEM and EDS analysis indicated that B4C and SiC were decomposed, carbon was preferentially evaporated under high thermal load, and a part of Si and Cu were melted, in addition, the splash of melted metal and the particle emission of brittle destruction were also found. Different erosive behaviors of carbon-based materials (CBMs) caused by laser and electron beam were also discussed.
文摘Changes of surface morphology following XeCI excimer laser irradiation were investigated for three engineering ceramic materials (Al2O3, Al2O3-SiC nanocomposite and Si3N4). Al2O3 and AI2O3-SiC nanocomposite samples exhibit a smooth rapid melt layer on the surface, and the formation of the metastabfe γ-Al2Oa was observed. A silicon-rich layer on the surface was formed after laser irradiation of Si3N4. The toughness K1c of the materials was measured by the indentation fracture method. After laser irradiation, the toughness of Al2O3, Al2O3-SiC nanocomposite and Si3N4 was improved to various degrees: Al2O3-SiC nanocomposite, 60% (max.); AI203, 40% (max.); Si3N4, 12% (max.).
基金Project supported by the Fund of Key Laboratory of Optoelectronic Materials Chemistry and Physics,Chinese Academy of Sciences(Grant No.2008DP173016)the National Key Research and Development Program of China(Grant No.2016YFB1102202)the National Key Research and Development Program of China(Grant No.2016YFB0701002)
文摘Dy：Lu2O3 was grown by the float-zone （Fz） method. According to the absorption spectrum, the Judd-Ofelt （JO） parameters Ω2, Ω4, and Ω6 were calculated to be 4.86 × 10-20 cm2, 2.02 × 10-20 cm2, and 1.76 ×10-20 cm2, respectively. The emission cross-section at 574 nm corresponding to the 4F9/2 →6H13/2 transition was calculated to be 0.53 ×10 20 cm2. The yellow （4F9/2 →6H13/2 transition） to blue （4F9/2 →6H15/2 transition） intensity ratio ranges up to 12.9. The fluorescence lifetime of the 4F9/2 energy level was measured to be 112.1 μs. These results reveal that Dy：Lu2O3 is a promising material for use in yellow lasers.
文摘Transparent polycrystaUine neodymiumdoped yttrium aluminum garnet ceramics （Nd：YAG） with better chemical stability, excellent optical and high temperature mechanical property is becoming a new laser host material. The Nd：YAG precursor powders with loosely dispersed, slightly agglomerated and YAG cubic crystal phase were synthesized at 1100 ℃ by the co-precipitation method combined with the reverse strike,
基金Project supported by the National Key Research and Development Program of China(Grant No.2016YFB1102301)the National Natural Science Foundation of China(Grant Nos.51272254,61405206,and 51502292)the Open Research Fund of the State Key Laboratory of Pulsed Power Laser Technology,Electronic Engineering Institute,China(Grant No.SKL2015KF01)
文摘We demonstrate the spectroscopic and laser performance before and after 100 Mrad gamma-ray irradiation on an Er,Pr：GYSGG crystal grown by the Czochralski method. The additional absorption of Er,Pr：GYSGG crystal is close to zero in the 968 nm pumping and 2.7-3 μm laser wavelength regions. The lifetimes of the upper and lower levels show faint decreases after gamma-ray irradiation. The maximum output powers of 542 and 526 mW with the slope efficiencies of 17.7% and 17.0% are obtained, respectively, on the GYSGG/Er,Pr：GYSGG composite crystal before and after the gammaray irradiation. These results suggest that Er,Pr：GYSGG crystal as a laser gain medium possesses a distinguished antiradiation ability for application in space and radiant environments.
基金supported by the National Natural Science Foundation of China(Nos.52171073,51801031,51775117)the Foshan Science and Technology Innovation Project,China(No.2018IT100112)+1 种基金the Research Fund of Key Laboratory of High Performance Manufacturing for Aero Engine(Northwestern Polytechnical University),Ministry of Industry and Information Technology,China(No.HPM-2020-06)the Fund of the State Key Laboratory of Solidification Processing in Northwestern Polytechnical University,China(No.SKLSP202014).
文摘The coupling strengthening principle of the double physical effect of plasma shock−cavitation was proposed,and the rationality of the cavitation effect in pulsed laser shock treatment under liquid−confined conditions needs to be confirmed urgently.The XRD testing method and 304 stainless steel,which is easy to obtain diffraction peaks,were selected to quantitatively detect and characterize the residual stress distribution in the action area of a single pulse laser beam.The test results and literature analysis show that the different process conditions of laser shock processing bring about different strength matching of the two stress effects of plasma shock and cavitation,and the main source of stress effect of femtosecond laser shock without coating is the cavitation effect.The actual effects of the laser pulse width and other process parameters such as the absorption layer and the constraint layer affect or determine the material modification principle of the pulsed laser surface treatment.
基金supported by the Shanghai Municipal Engineering Research Center for Sapphire Crystals,China(Grant No.14DZ2252500)the Fund of Key Laboratory of Optoelectronic Materials Chemistry and Physics,Chinese Academy of Sciences(Grant No.2008DP17301)+4 种基金the Fundamental Research Funds for the Central Universitiesthe National Natural Science Foundation of China and the China Academy of Engineering Physics Joint Fund(Grant No.U1530152)the National Natural Science Foundation of China(Grant Nos.61475177 and 61621001)the Shanghai Municipal Natural Science Foundation,China(Grant No.13ZR1446100)the MDE Key Laboratory of Advanced Micro-Structured Materials
文摘The 4-at.% Tm：Sc_2SiO_5 （Tm：SSO） crystal is successfully obtained by the Czochralski method. The optical properties and thermal conductivity of the crystal are investigated. The broad continuous wave（CW） laser output of（100）-cut Tm：SSO with the dimensions of 3 mm×3 mm×3 mm under laser diode（LD）-pumping is realized. The full width at half maximum（FWHM） of the laser emitting reaches up to 21 nm. The laser threshold of Tm：SSO is measured to be 0.43 W. Efficient diode-pumped CW laser performance of Tm：SSO is demonstrated with a slope efficiency of 25.9% and maximum output power of 934 mW.
基金Project supported by Shanghai Engineering Research Center for Sapphire Crystals,China(Grant No.14DZ2252500)the Fund of Key Laboratory of Optoelectronic Materials Chemistry and Physics Chinese Academy of Sciences(Grant No.2008DP17301)+4 种基金the Fundamental Research Funds for the Central Universities of Chinathe National Natural Science Foundation of China and China Academy of Engineering Physics Joint Fund(Grant No.U1530152)the National Natural Science Foundation of China(Grant Nos.61475177 and 61621001)the Natural Science Foundation of Shanghai Municiple,China(Grant No.13ZR1446100)the MOE Key Laboratory of Advanced Micro-Structured Materials of China
文摘A CaF2-CeF3 disordered crystal containing 1.06% of Er^3＋ ions was grown by the temperature gradient technique.Optical absorption and emission spectra recorded at room temperature and at 10 K, luminescence decay curve recorded at room temperature, and extended x-ray-absorption fine structure spectra were analyzed with an intention to assess the laser potential related to the ^4I13/2→^4I15/2 transition of Er^3＋. In addition, the thermal diffusivity of the crystal was measured at room temperature. The analysis of room-temperature spectra revealed that the ^4I13/2 emission is long-lived with a radiative lifetime value of 5.5 ms, peak emission cross section of 0.73 × 10^-20 cm^2, and large spectral width pointing at the tunability of the emission wavelength in the region stretching from approximately 1480 nm to 1630 nm. The energies of the crystal field components for the ground and excited multiplets determined from low-temperature absorption and emission spectra made it possible to predict successfully the spectral position and shape of the room-temperature ^4I13/2→^4I15/2 emission band. Based on the correlation of the optical spectra and dynamics of the luminescence decay, it was concluded that in contrast to Yb^3＋ ions in heavily doped CaF2 erbium ions in the CaF2-CeF3 crystal reside in numerous sites with dissimilar relaxation rates.
文摘Spectroscopic and fluorescence properties of Nd 3＋ ions in sodium fluoroborate（SFB） glasses were prepared and characterized through optical absorption,emission and decay measurements.The energy level analysis was carried out using free-ion Hamiltonian model.Experimental oscillator strengths were determined by measuring the area encompassed by the absorption peaks recorded for 1.0 mol.% Nd 3＋-doped glasses.The Judd-Ofelt parameters（2,4,6） were used to evaluate the laser characteristic parameters such as radiative transition probability（A R）,radiative decay time（τ R）,fluorescence branching ratio（β R） and stimulated emission cross-section（σ e） for the 4 F 3/2 metastable state.The fluorescence spectra for different concentrations of Nd 3＋ ions were recorded by exciting the samples at 514.5 nm Ar ＋ ion laser.
基金Project supported by National Natural Science Foundation of China(61275177,61475158,51302260)National Natural Science Foundation of Fujian Province(2014H0052)
文摘A Ca9Yb（VO4）7 crystal with dimensions of Φ23 mm×35 mm was grown successfully by Czochralski method. Its thermal conductivity was 1.06 W/（m？K） at room temperature. The absorption cross-sections at 980 nm were 1.80×10–20 cm2 and 1.28×10–20 cm2 for π- and σ- polarizations, respectively, with a full-width at half-maximum of 34 nm. The crystal had a broad emission at around 1025 nm with a full-width at half-maximum of 67 nm for π- polarization and 70 nm for σ- polarization. The emission cross-sections of the crystal were calculated by using reciprocity method and Füchtbauer-Ladenburg formula. The emission cross-sections at 1025 nm were 3.57×10–20 cm–2 and 1.91×10–20 cm–2 for π- and σ- polarization, respectively. The fluorescence lifetime was 332 μs. The results indicated that the crystal is a promising femtosecond and tunable laser material.
基金the support from the National Natural Science Foundation of China (No. 61925506)the Natural Science Foundation of Shanghai (No. 20JC1414605)+1 种基金Hangzhou Science and Technology Bureau of Zhejiang Province (No. TD2020002)the Academic/Technology Research Leader Program of Shanghai (23XD1404500)
文摘Lead halide perovskites have attracted considerable attention as potential candidates for high-performance nano/microlasers,owing to their outstanding optical properties.However,the further development of perovskite microlaser arrays(especially based on polycrystalline thin films)produced by the conventional processing techniques is hindered by the chemical instability and surface roughness of the perovskite structures.Herein,we demonstrate a laser patterning of large-scale,highly crystalline perovskite single-crystal films to fabricate reproducible perovskite single-crystal-based microlaser arrays.Perovskite thin films were directly ablated by femtosecond-laser in multiple low-power cycles at a minimum machining line width of approximately 300 nm to realize high-precision,chemically clean,and repeatable fabrication of microdisk arrays.The surface impurities generated during the process can be washed away to avoid external optical loss due to the robustness of the single-crystal film.Moreover,the high-quality,large-sized perovskite single-crystal films can significantly improve the quality of microcavities,thereby realizing a perovskite microdisk laser with narrow linewidth(0.09 nm)and low threshold(5.1µJ/cm2).Benefiting from the novel laser patterning method and the large-sized perovskite single-crystal films,a high power and high color purity laser display with single-mode microlasers as pixels was successfully fabricated.Thus,this study may offer a potential platform for mass-scale and reproducible fabrication of microlaser arrays,and further facilitate the development of highly integrated applications based on perovskite materials.
基金This project is supported by National Hi-tech Research and Development Program of China (863 Program, No.2002AA421150)Specialized Research Fund for the Doctoral Program of Higher Education of China (No.20030335091).
文摘The use of a CO2 laser system for fabrication of microfluidic chip on polymethyl methacrylate （PMMA） is presented to reduce fabrication cost and time of chip. The grooving process of the laser system and a model for the depth of microchannels are investigated. The relations between the depth of laser-cut channels and the laser beam power, velocity or the number of passes of the beam along the same channel are evaluated. In the experiments, the laser beam power varies from 0 to 50 W, the laser beam scanning velocity varies from 0 to 1 000 mm/s and the passes vary in the range of 1 to 10 times. Based on the principle of conservation of energy, the influence of the laser beam velocity, the laser power and the number of groove passes are examine. Considering the grooving interval energy loss, a modified mathematical model has been obtained and experimental data show good agreement with the theoretical model. This approach provides a simple way of predicting groove depths. The system provides a cost alternative of the other methods and it is especially useful on research work of rnicrofluidic prototyping due to the short cycle time of production.
基金supported by the Key Research and Development Program of Hebei Province(No.21351501D)A Provincial and Ministerial Scientific Research Project(LJ20212C031165)Basic Frontier Science and Technology Innovation Project of Army Engineering University of PLA(KYSZJQZL2210)。
文摘Sn_(1−x)Er_(x)O_(2)(x=0%,8%,16%,24%)micro/nanofibers were prepared by electrospinning combined with heat treatment using erbium nitrate,stannous chloride and polyvinylpyrrolidone(PVP)as raw materials.The target products were characterized by thermogravimetric analyzer,X-ray diffrotometer,fourier transform infrared spectrometer,scanning electron microscope,spectrophotometer and infrared emissivity tester,and the effects of Er^(3+)doping on its infrared and laser emissivity were studied.At the same time,the Sn_(1−x)Er_(x)O_(2)(x=0%,16%)doping models were constructed based on the first principles of density functional theory,and the related optoelectronic properties such as their energy band structure,density of states,reflectivity and dielectric constant were analyzed,and further explained the mechanism of Er^(3+)doping on SnO_(2)infrared emissivity and laser absorption from the point of electronic structure.The results showed that after calcination at 600℃,single rutile type SnO_(2)was formed,and the crystal structure was not changed by doping Er^(3+).The calcined products showed good fiber morphology,and the average fiber diameter was 402 nm.The infrared emissivity and resistivity of the samples both decreased first and then increased with the increase of Er^(3+)doping amount.When x=16%,the infrared emis-sivity of the sample was at least 0.71;and Er^(3+)doping can effectively reduce the reflectivity of SnO_(2)at 1.06μm and 1.55μm,when x=16%,its reflectivity at 1.06μm and 1.55μm are 50.5%and 40%,respectively,when x=24%,the reflectivity at 1.06μm and 1.55μm wavelengths are 47.3%and 42.1%,respectively.At the same time,the change of carrier concentration and electron transition before and after Er^(3+)doping were described by first-principle calculation,and the regulation mechanism of infrared emissivity and laser reflectivity was explained.This study provides a certain experimental and theoretical basis for the development of a single-type,light-weight and easily prepared infrared and laser compatible-stealth material.
文摘substitutes tion, high loosely dis Neodymium doped-yttrium aluminum garnet （Nd ： YAG） transparent polycrystalline ceramics already become of single crystals because they are provided with easy fabrication, low cost, large size, highly doped concentraheat conductivity, mass fabrication, multi-layers and multi-filnctions. The Nd：YAG precursor powders with persed , slightly agglomerated, super fine and YAG cubic crystal phase were synthesized at 1100 ℃ by the homogeneous precipitation method, using Nd2O3, Y2O3, Al（NO3）3·9H2O and urea as raw materials, （NH4）2SO4 as electrical stabilizer, TEOS as sintering additive. The Nd：YAG transparent ceramics were prepared after being vacuum sintered at 1700 ℃ for 5 h. The Nd：YAG ceramic materials were characterized by the TG-DTA, XRD, FT-IR, TEM, FEG-ESEM and FT-PL. The results show that the crystallization temperature of YAG is 850 ℃ and the intermediate crystal phase YAP forming during the heat treatment transforms to YAG cubic crystal phase at 1050 ℃. The lasing wavelength of （Nd0.01 Y0.99）3Al5O12 transparent ceramics is 1.065 μm and there exists a slight red-shift compared to the single crystal with the same chemical composition. The optical transmittance is 45 % in the visible light and 58 % in the near infrared light and the optical transmittance descends with the decreasing the wavelength.
