冶金尘泥的转底炉处理工艺是目前钢铁行业采用的主要处置工艺,但在实际生产过程中经常出现还原焙烧不均匀的问题。利用微观扫描电子显微镜(scanning electron microscopy,SEM)分析结合宏观Maps统计分析,对冶金尘泥还原焙烧的不均匀性进...冶金尘泥的转底炉处理工艺是目前钢铁行业采用的主要处置工艺,但在实际生产过程中经常出现还原焙烧不均匀的问题。利用微观扫描电子显微镜(scanning electron microscopy,SEM)分析结合宏观Maps统计分析,对冶金尘泥还原焙烧的不均匀性进行详细的可视化、数据化分析。研究结果表明,冶金尘泥在焙烧温度为1250℃、焙烧时间为15 min的条件下,熟球金属化率达到89.04%、脱锌率达到81.66%、抗压强度达到3.03 kN,熟球金属化率和脱锌率会随着焙烧温度提高和焙烧时间延长而进一步提高,但熟球抗压强度在焙烧时间过长时反而逐渐降低;熟球Maps统计分析表明,提高焙烧温度更有利于提高熟球外圈和下部的还原程度,而延长焙烧时间也更有利于提高熟球下部还原程度,但对熟球内部和外圈还原程度的提升作用比较相似;同时,提高焙烧温度也更有利于提升熟球下部的致密化程度,降低熟球上、下孔隙结构的不均匀性,进而显著提高熟球整体抗压强度;但焙烧时间过长会导致熟球中小孔隙融合为大孔隙,反而降低熟球抗压强度。此外,熟球中硅酸盐(渣相)和浮氏体(FexO)更容易破裂,而金属铁(Fe)可延缓裂纹蔓延,因而,适当提高熟球金属化率、降低硅酸盐(渣相)含量也有利于提高其抗压强度。基于Maps统计分析探究了冶金尘泥还原焙烧过程中物相及孔隙的变化规律,分析结果可以为转底炉工艺处理冶金尘泥的生产实践提供指导和建议。展开更多
The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from...The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).展开更多
Network-on-Chip(NoC)systems are progressively deployed in connecting massively parallel megacore systems in the new computing architecture.As a result,application mapping has become an important aspect of performance ...Network-on-Chip(NoC)systems are progressively deployed in connecting massively parallel megacore systems in the new computing architecture.As a result,application mapping has become an important aspect of performance and scalability,as current trends require the distribution of computation across network nodes/points.In this paper,we survey a large number of mapping and scheduling techniques designed for NoC architectures.This time,we concentrated on 3D systems.We take a systematic literature review approach to analyze existing methods across static,dynamic,hybrid,and machine-learning-based approaches,alongside preliminary AI-based dynamic models in recent works.We classify them into several main aspects covering power-aware mapping,fault tolerance,load-balancing,and adaptive for dynamic workloads.Also,we assess the efficacy of each method against performance parameters,such as latency,throughput,response time,and error rate.Key challenges,including energy efficiency,real-time adaptability,and reinforcement learning integration,are highlighted as well.To the best of our knowledge,this is one of the recent reviews that identifies both traditional and AI-based algorithms for mapping over a modern NoC,and opens research challenges.Finally,we provide directions for future work toward improved adaptability and scalability via lightweight learned models and hierarchical mapping frameworks.展开更多
This paper presents an intelligent patrol and security robot integrating 2D LiDAR and RGB-D vision sensors to achieve semantic simultaneous localization and mapping(SLAM),real-time object recognition,and dynamic obsta...This paper presents an intelligent patrol and security robot integrating 2D LiDAR and RGB-D vision sensors to achieve semantic simultaneous localization and mapping(SLAM),real-time object recognition,and dynamic obstacle avoidance.The system employs the YOLOv7 deep-learning framework for semantic detection and SLAM for localization and mapping,fusing geometric and visual data to build a high-fidelity 2D semantic map.This map enables the robot to identify and project object information for improved situational awareness.Experimental results show that object recognition reached 95.4%mAP@0.5.Semantic completeness increased from 68.7%(single view)to 94.1%(multi-view)with an average position error of 3.1 cm.During navigation,the robot achieved 98.0%reliability,avoided moving obstacles in 90.0%of encounters,and replanned paths in 0.42 s on average.The integration of LiDAR-based SLAMwith deep-learning–driven semantic perception establishes a robust foundation for intelligent,adaptive,and safe robotic navigation in dynamic environments.展开更多
Populus species,important economic species combining rapid growth with broad ecological adaptability,play a critical role in sustainable forestry and bioenergy production.In this study,we performed whole-genome resequ...Populus species,important economic species combining rapid growth with broad ecological adaptability,play a critical role in sustainable forestry and bioenergy production.In this study,we performed whole-genome resequencing of 707 individuals from a full-sib family to develop comprehensive single nucleotide polymorphism(SNP)markers and constructed a high-density genetic linkage map of 19 linkage groups.The total genetic length of the map reached 3623.65 cM with an average marker interval of 0.34 cM.By integrating multidimensional phenotypic data,89 quantitative trait loci(QTL)associated with growth,wood physical and chemical properties,disease resistance,and leaf morphology traits were identified,with logarithm of odds(LOD)scores ranging from 3.13 to 21.72 Notably,pleiotropic analysis revealed significant colocaliza and phenotypic variance explained between 1.7% and 11.6%.-tion hotspots on chromosomes LG1,LG5,LG6,LG8,and LG14,with epistatic interaction network analysis confirming genetic basis of coordinated regulation across multiple traits.Functional annotation of 207 candidate genes showed that R2R3-MYB and bHLH transcription factors and pyruvate kinase-encoding genes were significantly enriched,suggesting crucial roles in lignin biosynthesis and carbon metabolic pathways.Allelic effect analysis indicated that the frequency of favorable alleles associated with target traits ranged from 0.20 to 0.55.Incorporation of QTL-derived favorable alleles as random effects into Bayesian-based genomic selection models led to an increase in prediction accuracy ranging from 1% to 21%,with Bayesian ridge regression as the best predictive model.This study provides valuable genomic resources and genetic insights for deciphering complex trait architecture and advancing molecular breeding in poplar.展开更多
Most Convolutional Neural Network(CNN)interpretation techniques visualize only the dominant cues that the model relies on,but there is no guarantee that these represent all the evidence the model uses for classificati...Most Convolutional Neural Network(CNN)interpretation techniques visualize only the dominant cues that the model relies on,but there is no guarantee that these represent all the evidence the model uses for classification.This limitation becomes critical when hidden secondary cues—potentially more meaningful than the visualized ones—remain undiscovered.This study introduces CasCAM(Cascaded Class Activation Mapping)to address this fundamental limitation through counterfactual reasoning.By asking“if this dominant cue were absent,what other evidence would the model use?”,CasCAM progressively masks the most salient features and systematically uncovers the hierarchy of classification evidence hidden beneath them.Experimental results demonstrate that CasCAM effectively discovers the full spectrum of reasoning evidence and can be universally applied with nine existing interpretation methods.展开更多
Objective:To retrospectively evaluate the diagnostic efficacy of traditional MRI and T2 Mapping quantitative imaging technology for knee joint cartilage injury,clarify the differences in diagnostic value of the two im...Objective:To retrospectively evaluate the diagnostic efficacy of traditional MRI and T2 Mapping quantitative imaging technology for knee joint cartilage injury,clarify the differences in diagnostic value of the two imaging methods in different injury grades and different cartilage subregions,and provide evidence-based basis for the accurate diagnosis of clinical cartilage injury.Methods:Clinical and imaging data of 286 patients with knee joint lesions admitted to the Affiliated Hospital of Xiangtan Medicine and Health Vocational College from January 2020 to June 2023 were collected retrospectively.All patients underwent both traditional MRI sequences and T2 Mapping sequences.The knee joint cartilage was divided into 14 subregions.Two senior radiologists independently diagnosed the images of the two imaging technologies using a blind method and recorded the cartilage injury grades.The sensitivity,specificity,accuracy,positive predictive value,negative predictive value,and area under the receiver operating characteristic curve(AUC)of the two technologies for diagnosing cartilage injury were calculated and compared,and the differences in their diagnostic efficacy in different injury grades and different subregions were analyzed.Results:A total of 4004 cartilage subregions from 286 patients were included in the analysis,including 1836 injured subregions and 2168 normal subregions.The overall sensitivity(89.7%),accuracy(91.2%),and AUC(0.946)of T2 Mapping quantitative imaging for diagnosing cartilage injury were significantly higher than those of traditional MRI(76.3%,82.5%,and 0.852 respectively),with statistically significant differences(p<0.001);there was no significant difference in specificity between the two(93.5%vs 90.8%,p=0.062).Subgroup analysis showed that T2 Mapping had the most significant diagnostic advantage in early cartilage injury(Grade 1),with sensitivity(78.5%)33.2%higher than that of traditional MRI(45.3%)(p<0.001).Conclusion:The diagnostic efficacy of T2 Mapping quantitative imaging for knee joint cartilage injury is significantly superior to that of traditional MRI,especially in the detection of early cartilage injury and accurate evaluation of weight-bearing area injury.Data verify its clinical applicability and reliability.It can be used as an important supplementary method to traditional MRI,and is recommended for the early diagnosis,grading evaluation,and clinical follow-up of cartilage injury.展开更多
Oxide dispersion strengthened(ODS)alloys are extensively used owing to high thermostability and creep strength contributed from uniformly dispersed fine oxides particles.However,the existence of these strengthening pa...Oxide dispersion strengthened(ODS)alloys are extensively used owing to high thermostability and creep strength contributed from uniformly dispersed fine oxides particles.However,the existence of these strengthening particles also deteriorates the processability and it is of great importance to establish accurate processing maps to guide the thermomechanical processes to enhance the formability.In this study,we performed particle swarm optimization-based back propagation artificial neural network model to predict the high temperature flow behavior of 0.25wt%Al2O3 particle-reinforced Cu alloys,and compared the accuracy with that of derived by Arrhenius-type constitutive model and back propagation artificial neural network model.To train these models,we obtained the raw data by fabricating ODS Cu alloys using the internal oxidation and reduction method,and conducting systematic hot compression tests between 400 and800℃with strain rates of 10^(-2)-10 S^(-1).At last,processing maps for ODS Cu alloys were proposed by combining processing parameters,mechanical behavior,microstructure characterization,and the modeling results achieved a coefficient of determination higher than>99%.展开更多
Accurate and rapid recognition of weathering degree(WD)and groundwater condition(GC)is essential for evaluating rock mass quality and conducting stability analyses in underground engineering.Conventional WD and GC rec...Accurate and rapid recognition of weathering degree(WD)and groundwater condition(GC)is essential for evaluating rock mass quality and conducting stability analyses in underground engineering.Conventional WD and GC recognition methods often rely on subjective evaluation by field experts,supplemented by field sampling and laboratory testing.These methods are frequently complex and timeconsuming,making it challenging to meet the rapidly evolving demands of underground engineering.Therefore,this study proposes a rock non-geometric parameter classification network(RNPC-net)to rapidly achieve the recognition and mapping ofWD and GC of tunnel faces.The hybrid feature extraction module(HFEM)in RNPC-net can fully extract,fuse,and utilize multi-scale features of images,enhancing the network's classification performance.Moreover,the designed adaptive weighting auxiliary classifier(AC)helps the network learn features more efficiently.Experimental results show that RNPC-net achieved classification accuracies of 0.8756 and 0.8710 for WD and GC,respectively,representing an improvement of approximately 2%e10%compared to other methods.Both quantitative and qualitative experiments confirm the effectiveness and superiority of RNPC-net.Furthermore,for WD and GC mapping,RNPC-net outperformed other methods by achieving the highest mean intersection over union(mIOU)across most tunnel faces.The mapping results closely align with measurements provided by field experts.The application of WD and GC mapping results to the rock mass rating(RMR)system achieved a transition from conventional qualitative to quantitative evaluation.This advancement enables more accurate and reliable rock mass quality evaluations,particularly under critical conditions of RMR.展开更多
Cotton is an important global cash crops that serve as the primary source of natural fiber for textiles.A thorough understand-ing of the long-term variations in cotton cultivation is vital for optimizing cotton cultiv...Cotton is an important global cash crops that serve as the primary source of natural fiber for textiles.A thorough understand-ing of the long-term variations in cotton cultivation is vital for optimizing cotton cultivation management and promoting the sustainable development of the cotton industry.Xinjiang is the primary cotton-producing region in China.However,long-term data of cotton cultiv-ation areas with high spatial resolution are unavailable for Xinjiang,China.Therefore,this study aimed to identify and map an accurate 30-m cotton cultivation area dataset in Xinjiang from 2000 to 2020 by applying a Random Forest(RF)-based method that integrates Landsat and Moderate Resolution Imaging Spectroradiometer(MODIS)images,and validated the applicability and accuracy of dataset at a large spatial scale.Then,this study analyzed the spatiotemporal variations and influencing factors of cotton cultivation in the study period.The results showed that a high classification accuracy was achieved(overall accuracy>85%,F1>0.80),strongly agreeing with county-level agricultural statistical yearbook data(R2>0.72).Significant spatiotemporal variation in the cotton cultivation areas was found in Xinjiang,with a total increase of 1131.26 kha from 2000 to 2020.Notably,cotton cultivation area in southern Xinjiang expan-ded substantially,with that in Aksu increasing from 20.10%in 2000 to 28.17%in 2020,representing an expansion of 374.29 kha.In northern Xinjiang,the cotton areas in the Tacheng region also exhibited significant increased by almost ten percentage points in the same period.In contrast,cotton cultivation in eastern Xinjiang declined,decreasing from 2.22%in 2000 to merely 0.24%in 2020.Standard deviation ellipse analysis revealed a‘northeast-southwest’spatial distribution,with the centroid consistently located in Aksu and shifting 102.96 km over the 20-yr period.Pearson correlation analysis indicated that socioeconomic factors had a stronger influence on cotton cultivation than climatic factors,with effective irrigation area(r=0.963,P<0.05)and total agricultural machinery power(r=0.823)showing significant positive correlations,whereas climatic variables exhibiting weak associations(r<0.200).These results provide valuable scientific data for informed agricultural management,sustainable development,and policymaking.展开更多
This study presents a reflective bibliometric review of 1457 peer-reviewed articles published in the Journal of Psychology in Africa(2008-2024,17 years),using a Meta-Editorial Mapping Framework(MEMF)analysis.The MEMF ...This study presents a reflective bibliometric review of 1457 peer-reviewed articles published in the Journal of Psychology in Africa(2008-2024,17 years),using a Meta-Editorial Mapping Framework(MEMF)analysis.The MEMF integrates citation metrics,keyword novelty ratios,TF-IDF weighting,and cluster-based topic modeling to trace long-term thematic trends and editorial evolution.Findings reveal sustained attention to foundational domains such as mental health,education,and identity,alongside a gradual integration of emergent themes including digital well-being,organizational behavior,and post-pandemic adaptation.Articles with moderate topical novelty(40%-60% new keywords)achieved the highest citation and usage metrics,suggesting that integrative innovation enhances scholarly impact.Clustering analyses indicate that the journal’s content forms overlapping conceptual domains rather than isolated silos.These insights contribute to editorial strategy,authorial positioning,and the future design of regional academic platforms.Moreover,the findings provide evidence supporting the use of the MEMF as a replicable tool for meta-editorial analysis across disciplinary and geographic boundaries.展开更多
文摘冶金尘泥的转底炉处理工艺是目前钢铁行业采用的主要处置工艺,但在实际生产过程中经常出现还原焙烧不均匀的问题。利用微观扫描电子显微镜(scanning electron microscopy,SEM)分析结合宏观Maps统计分析,对冶金尘泥还原焙烧的不均匀性进行详细的可视化、数据化分析。研究结果表明,冶金尘泥在焙烧温度为1250℃、焙烧时间为15 min的条件下,熟球金属化率达到89.04%、脱锌率达到81.66%、抗压强度达到3.03 kN,熟球金属化率和脱锌率会随着焙烧温度提高和焙烧时间延长而进一步提高,但熟球抗压强度在焙烧时间过长时反而逐渐降低;熟球Maps统计分析表明,提高焙烧温度更有利于提高熟球外圈和下部的还原程度,而延长焙烧时间也更有利于提高熟球下部还原程度,但对熟球内部和外圈还原程度的提升作用比较相似;同时,提高焙烧温度也更有利于提升熟球下部的致密化程度,降低熟球上、下孔隙结构的不均匀性,进而显著提高熟球整体抗压强度;但焙烧时间过长会导致熟球中小孔隙融合为大孔隙,反而降低熟球抗压强度。此外,熟球中硅酸盐(渣相)和浮氏体(FexO)更容易破裂,而金属铁(Fe)可延缓裂纹蔓延,因而,适当提高熟球金属化率、降低硅酸盐(渣相)含量也有利于提高其抗压强度。基于Maps统计分析探究了冶金尘泥还原焙烧过程中物相及孔隙的变化规律,分析结果可以为转底炉工艺处理冶金尘泥的生产实践提供指导和建议。
基金Sichuan Science and Technology Program(2025ZNSFSC1341)Fundamental Research Funds for the Central Universities(J2022-090,25CAFUC04087)。
文摘The hot compression deformation behavior of Mg-6Zn-1Mn-0.5Ca(ZM61-0.5Ca)and Mg-6Zn-1Mn-2Sn-0.5Ca(ZMT612-0.5Ca)alloys was investigated at deformation temperatures ranging from 250℃to 400℃and strain rates varying from 0.001 s^(-1) to 1 s^(-1).The results show that the addition of Sn promotes dynamic recrystallization(DRX),and CaMgSn phases can act as nucleation sites during the compression deformation.Flow stress increases with increasing the strain rate and decreasing the temperature.Both the ZM61-0.5Ca and ZMT612-0.5Ca alloys exhibit obvious DRX characteristics.CaMgSn phases can effectively inhibit dislocation motion with the addition of Sn,thus increasing the peak fl ow stress of the alloy.The addition of Sn increases the hot deformation activation energy of the ZM61-0.5Ca alloy from 199.654 kJ/mol to 276.649 kJ/mol,thus improving the thermal stability of the alloy.For the ZMT612-0.5Ca alloy,the optimal hot deformation parameters are determined to be a deformation temperature range of 350–400℃and a strain rate range of 0.001–0.01 s^(-1).
文摘Network-on-Chip(NoC)systems are progressively deployed in connecting massively parallel megacore systems in the new computing architecture.As a result,application mapping has become an important aspect of performance and scalability,as current trends require the distribution of computation across network nodes/points.In this paper,we survey a large number of mapping and scheduling techniques designed for NoC architectures.This time,we concentrated on 3D systems.We take a systematic literature review approach to analyze existing methods across static,dynamic,hybrid,and machine-learning-based approaches,alongside preliminary AI-based dynamic models in recent works.We classify them into several main aspects covering power-aware mapping,fault tolerance,load-balancing,and adaptive for dynamic workloads.Also,we assess the efficacy of each method against performance parameters,such as latency,throughput,response time,and error rate.Key challenges,including energy efficiency,real-time adaptability,and reinforcement learning integration,are highlighted as well.To the best of our knowledge,this is one of the recent reviews that identifies both traditional and AI-based algorithms for mapping over a modern NoC,and opens research challenges.Finally,we provide directions for future work toward improved adaptability and scalability via lightweight learned models and hierarchical mapping frameworks.
基金supported by the National Science and Technology Council of under Grant NSTC 114-2221-E-130-007.
文摘This paper presents an intelligent patrol and security robot integrating 2D LiDAR and RGB-D vision sensors to achieve semantic simultaneous localization and mapping(SLAM),real-time object recognition,and dynamic obstacle avoidance.The system employs the YOLOv7 deep-learning framework for semantic detection and SLAM for localization and mapping,fusing geometric and visual data to build a high-fidelity 2D semantic map.This map enables the robot to identify and project object information for improved situational awareness.Experimental results show that object recognition reached 95.4%mAP@0.5.Semantic completeness increased from 68.7%(single view)to 94.1%(multi-view)with an average position error of 3.1 cm.During navigation,the robot achieved 98.0%reliability,avoided moving obstacles in 90.0%of encounters,and replanned paths in 0.42 s on average.The integration of LiDAR-based SLAMwith deep-learning–driven semantic perception establishes a robust foundation for intelligent,adaptive,and safe robotic navigation in dynamic environments.
基金supported by the National Key Research and Development Plan of China(2021YFD2200202)the Key Research and Development Project of Jiangsu Province,China(BE2021366).
文摘Populus species,important economic species combining rapid growth with broad ecological adaptability,play a critical role in sustainable forestry and bioenergy production.In this study,we performed whole-genome resequencing of 707 individuals from a full-sib family to develop comprehensive single nucleotide polymorphism(SNP)markers and constructed a high-density genetic linkage map of 19 linkage groups.The total genetic length of the map reached 3623.65 cM with an average marker interval of 0.34 cM.By integrating multidimensional phenotypic data,89 quantitative trait loci(QTL)associated with growth,wood physical and chemical properties,disease resistance,and leaf morphology traits were identified,with logarithm of odds(LOD)scores ranging from 3.13 to 21.72 Notably,pleiotropic analysis revealed significant colocaliza and phenotypic variance explained between 1.7% and 11.6%.-tion hotspots on chromosomes LG1,LG5,LG6,LG8,and LG14,with epistatic interaction network analysis confirming genetic basis of coordinated regulation across multiple traits.Functional annotation of 207 candidate genes showed that R2R3-MYB and bHLH transcription factors and pyruvate kinase-encoding genes were significantly enriched,suggesting crucial roles in lignin biosynthesis and carbon metabolic pathways.Allelic effect analysis indicated that the frequency of favorable alleles associated with target traits ranged from 0.20 to 0.55.Incorporation of QTL-derived favorable alleles as random effects into Bayesian-based genomic selection models led to an increase in prediction accuracy ranging from 1% to 21%,with Bayesian ridge regression as the best predictive model.This study provides valuable genomic resources and genetic insights for deciphering complex trait architecture and advancing molecular breeding in poplar.
基金supported by the Basic Science Research Program through the National Research Foundation of Korea(NRF),funded by the Ministry of Education(RS-2023-00249743).
文摘Most Convolutional Neural Network(CNN)interpretation techniques visualize only the dominant cues that the model relies on,but there is no guarantee that these represent all the evidence the model uses for classification.This limitation becomes critical when hidden secondary cues—potentially more meaningful than the visualized ones—remain undiscovered.This study introduces CasCAM(Cascaded Class Activation Mapping)to address this fundamental limitation through counterfactual reasoning.By asking“if this dominant cue were absent,what other evidence would the model use?”,CasCAM progressively masks the most salient features and systematically uncovers the hierarchy of classification evidence hidden beneath them.Experimental results demonstrate that CasCAM effectively discovers the full spectrum of reasoning evidence and can be universally applied with nine existing interpretation methods.
基金Application Research of MRI Physiological Quantitative Imaging Technology in the Diagnosis of Cartilage Injury(Project No.:RCYJ2021-04)。
文摘Objective:To retrospectively evaluate the diagnostic efficacy of traditional MRI and T2 Mapping quantitative imaging technology for knee joint cartilage injury,clarify the differences in diagnostic value of the two imaging methods in different injury grades and different cartilage subregions,and provide evidence-based basis for the accurate diagnosis of clinical cartilage injury.Methods:Clinical and imaging data of 286 patients with knee joint lesions admitted to the Affiliated Hospital of Xiangtan Medicine and Health Vocational College from January 2020 to June 2023 were collected retrospectively.All patients underwent both traditional MRI sequences and T2 Mapping sequences.The knee joint cartilage was divided into 14 subregions.Two senior radiologists independently diagnosed the images of the two imaging technologies using a blind method and recorded the cartilage injury grades.The sensitivity,specificity,accuracy,positive predictive value,negative predictive value,and area under the receiver operating characteristic curve(AUC)of the two technologies for diagnosing cartilage injury were calculated and compared,and the differences in their diagnostic efficacy in different injury grades and different subregions were analyzed.Results:A total of 4004 cartilage subregions from 286 patients were included in the analysis,including 1836 injured subregions and 2168 normal subregions.The overall sensitivity(89.7%),accuracy(91.2%),and AUC(0.946)of T2 Mapping quantitative imaging for diagnosing cartilage injury were significantly higher than those of traditional MRI(76.3%,82.5%,and 0.852 respectively),with statistically significant differences(p<0.001);there was no significant difference in specificity between the two(93.5%vs 90.8%,p=0.062).Subgroup analysis showed that T2 Mapping had the most significant diagnostic advantage in early cartilage injury(Grade 1),with sensitivity(78.5%)33.2%higher than that of traditional MRI(45.3%)(p<0.001).Conclusion:The diagnostic efficacy of T2 Mapping quantitative imaging for knee joint cartilage injury is significantly superior to that of traditional MRI,especially in the detection of early cartilage injury and accurate evaluation of weight-bearing area injury.Data verify its clinical applicability and reliability.It can be used as an important supplementary method to traditional MRI,and is recommended for the early diagnosis,grading evaluation,and clinical follow-up of cartilage injury.
基金financial support of the National Natural Science Foundation of China(No.52371103)the Fundamental Research Funds for the Central Universities,China(No.2242023K40028)+1 种基金the Open Research Fund of Jiangsu Key Laboratory for Advanced Metallic Materials,China(No.AMM2023B01).financial support of the Research Fund of Shihezi Key Laboratory of AluminumBased Advanced Materials,China(No.2023PT02)financial support of Guangdong Province Science and Technology Major Project,China(No.2021B0301030005)。
文摘Oxide dispersion strengthened(ODS)alloys are extensively used owing to high thermostability and creep strength contributed from uniformly dispersed fine oxides particles.However,the existence of these strengthening particles also deteriorates the processability and it is of great importance to establish accurate processing maps to guide the thermomechanical processes to enhance the formability.In this study,we performed particle swarm optimization-based back propagation artificial neural network model to predict the high temperature flow behavior of 0.25wt%Al2O3 particle-reinforced Cu alloys,and compared the accuracy with that of derived by Arrhenius-type constitutive model and back propagation artificial neural network model.To train these models,we obtained the raw data by fabricating ODS Cu alloys using the internal oxidation and reduction method,and conducting systematic hot compression tests between 400 and800℃with strain rates of 10^(-2)-10 S^(-1).At last,processing maps for ODS Cu alloys were proposed by combining processing parameters,mechanical behavior,microstructure characterization,and the modeling results achieved a coefficient of determination higher than>99%.
基金supported by the National Natural Science Foundation of China(Grant Nos.42077242 and 42171407)the Graduate Innovation Fund of Jilin University.
文摘Accurate and rapid recognition of weathering degree(WD)and groundwater condition(GC)is essential for evaluating rock mass quality and conducting stability analyses in underground engineering.Conventional WD and GC recognition methods often rely on subjective evaluation by field experts,supplemented by field sampling and laboratory testing.These methods are frequently complex and timeconsuming,making it challenging to meet the rapidly evolving demands of underground engineering.Therefore,this study proposes a rock non-geometric parameter classification network(RNPC-net)to rapidly achieve the recognition and mapping ofWD and GC of tunnel faces.The hybrid feature extraction module(HFEM)in RNPC-net can fully extract,fuse,and utilize multi-scale features of images,enhancing the network's classification performance.Moreover,the designed adaptive weighting auxiliary classifier(AC)helps the network learn features more efficiently.Experimental results show that RNPC-net achieved classification accuracies of 0.8756 and 0.8710 for WD and GC,respectively,representing an improvement of approximately 2%e10%compared to other methods.Both quantitative and qualitative experiments confirm the effectiveness and superiority of RNPC-net.Furthermore,for WD and GC mapping,RNPC-net outperformed other methods by achieving the highest mean intersection over union(mIOU)across most tunnel faces.The mapping results closely align with measurements provided by field experts.The application of WD and GC mapping results to the rock mass rating(RMR)system achieved a transition from conventional qualitative to quantitative evaluation.This advancement enables more accurate and reliable rock mass quality evaluations,particularly under critical conditions of RMR.
基金Under the auspices of the National Natural Science Foundation of China(No.42101342,U2243205)the Third Comprehensive Scientific Expedition to Xinjiang(No.2021XJKK1403)。
文摘Cotton is an important global cash crops that serve as the primary source of natural fiber for textiles.A thorough understand-ing of the long-term variations in cotton cultivation is vital for optimizing cotton cultivation management and promoting the sustainable development of the cotton industry.Xinjiang is the primary cotton-producing region in China.However,long-term data of cotton cultiv-ation areas with high spatial resolution are unavailable for Xinjiang,China.Therefore,this study aimed to identify and map an accurate 30-m cotton cultivation area dataset in Xinjiang from 2000 to 2020 by applying a Random Forest(RF)-based method that integrates Landsat and Moderate Resolution Imaging Spectroradiometer(MODIS)images,and validated the applicability and accuracy of dataset at a large spatial scale.Then,this study analyzed the spatiotemporal variations and influencing factors of cotton cultivation in the study period.The results showed that a high classification accuracy was achieved(overall accuracy>85%,F1>0.80),strongly agreeing with county-level agricultural statistical yearbook data(R2>0.72).Significant spatiotemporal variation in the cotton cultivation areas was found in Xinjiang,with a total increase of 1131.26 kha from 2000 to 2020.Notably,cotton cultivation area in southern Xinjiang expan-ded substantially,with that in Aksu increasing from 20.10%in 2000 to 28.17%in 2020,representing an expansion of 374.29 kha.In northern Xinjiang,the cotton areas in the Tacheng region also exhibited significant increased by almost ten percentage points in the same period.In contrast,cotton cultivation in eastern Xinjiang declined,decreasing from 2.22%in 2000 to merely 0.24%in 2020.Standard deviation ellipse analysis revealed a‘northeast-southwest’spatial distribution,with the centroid consistently located in Aksu and shifting 102.96 km over the 20-yr period.Pearson correlation analysis indicated that socioeconomic factors had a stronger influence on cotton cultivation than climatic factors,with effective irrigation area(r=0.963,P<0.05)and total agricultural machinery power(r=0.823)showing significant positive correlations,whereas climatic variables exhibiting weak associations(r<0.200).These results provide valuable scientific data for informed agricultural management,sustainable development,and policymaking.
文摘This study presents a reflective bibliometric review of 1457 peer-reviewed articles published in the Journal of Psychology in Africa(2008-2024,17 years),using a Meta-Editorial Mapping Framework(MEMF)analysis.The MEMF integrates citation metrics,keyword novelty ratios,TF-IDF weighting,and cluster-based topic modeling to trace long-term thematic trends and editorial evolution.Findings reveal sustained attention to foundational domains such as mental health,education,and identity,alongside a gradual integration of emergent themes including digital well-being,organizational behavior,and post-pandemic adaptation.Articles with moderate topical novelty(40%-60% new keywords)achieved the highest citation and usage metrics,suggesting that integrative innovation enhances scholarly impact.Clustering analyses indicate that the journal’s content forms overlapping conceptual domains rather than isolated silos.These insights contribute to editorial strategy,authorial positioning,and the future design of regional academic platforms.Moreover,the findings provide evidence supporting the use of the MEMF as a replicable tool for meta-editorial analysis across disciplinary and geographic boundaries.
