The tensile strength of rocks under real-time high-temperatures is essential for enhanced geothermal system development.However,the complex occurrence and deep burial of hot dry rocks limit the quantity and quality of...The tensile strength of rocks under real-time high-temperatures is essential for enhanced geothermal system development.However,the complex occurrence and deep burial of hot dry rocks limit the quantity and quality of standard samples for mechanical testing.This paper compared the tensile strengths obtained from Brazilian splitting tests on standard samples(with a diameter of 50 mm and a thickness of 25 mm)and micro-tensile samples(with a diameter of 50 mm and a thickness of 25 mm)of two types of granites.A power-law size effect model was established between the two sets of data,validating the reliability of the testing method.Then,miniature Brazilian splitting under real-time high-temperature,combined with X-ray diffraction(XRD)revealed temperature-dependent strength variations and microstructural damage mechanisms.The results show that:(1)The comparison error between the tensile strength obtained by the fitting model and that of the measured standard samples was less than 6%.(2)In real-time high-temperature conditions,tensile strength of granite exhibited non-monotonic behavior,increasing below 300°C before decreasing,with sharp declines at 400–500°C and 600–700°C.(3)Thermal damage stems from the differences in the high-temperature behavior of minerals,including dehydration,phase transformation,and differential expansion.展开更多
This study investigated the physicochemical properties,enzyme activities,volatile flavor components,microbial communities,and sensory evaluation of high-temperature Daqu(HTD)during the maturation process,and a standar...This study investigated the physicochemical properties,enzyme activities,volatile flavor components,microbial communities,and sensory evaluation of high-temperature Daqu(HTD)during the maturation process,and a standard system was established for comprehensive quality evaluation of HTD.There were obvious changes in the physicochemical properties,enzyme activities,and volatile flavor components at different storage periods,which affected the sensory evaluation of HTD to a certain extent.The results of high-throughput sequencing revealed significant microbial diversity,and showed that the bacterial community changed significantly more than did the fungal community.During the storage process,the dominant bacterial genera were Kroppenstedtia and Thermoascus.The correlation between dominant microorganisms and quality indicators highlighted their role in HTD quality.Lactococcus,Candida,Pichia,Paecilomyces,and protease activity played a crucial role in the formation of isovaleraldehyde.Acidic protease activity had the greatest impact on the microbial community.Moisture promoted isobutyric acid generation.Furthermore,the comprehensive quality evaluation standard system was established by the entropy weight method combined with multi-factor fuzzy mathematics.Consequently,this study provides innovative insights for comprehensive quality evaluation of HTD during storage and establishes a groundwork for scientific and rational storage of HTD and quality control of sauce-flavor Baijiu.展开更多
High-nickel ternary cathodes hold a great application prospect in solid-state lithium metal batteries to achieve high-energy density,but they still suffer from structural instability and detrimental side reactions wit...High-nickel ternary cathodes hold a great application prospect in solid-state lithium metal batteries to achieve high-energy density,but they still suffer from structural instability and detrimental side reactions with the solid-state electrolytes.To circumvent these issues,a continuous uniform layer polyacrylonitrile(PAN)was introduced on the surface of LiNi_(0.8)Mn_(0.1)Co_(0.1)O_(2) via in situ polymerization of acrylonitrile(AN).Furthermore,the partial-cyclized treatment of PAN(cPAN)coating layer presents high ionic and electron conductivity,which can accelerate interfacial Li+and electron diffusion simultaneously.And the thermodynamically stabilized cPAN coating layer cannot only effectively inhibit detrimental side reactions between cathode and solid-state electrolytes but also provide a homogeneous stress to simultaneously address the problems of bulk structural degradation,which contributes to the exceptional mechanical and electrochemical stabilities of the modified electrode.Besides,the coordination bond interaction between the cPAN and NCM811 can suppress the migration of Ni to elevate the stability of the crystal structure.Benefited from these,the In-cPAN-260@NCM811 shows excellent cycling performance with a retention of 86.8%after 300 cycles and superior rate capability.And endow the solid-state battery with thermal safety stability even at hightemperature extreme environment.This facile and scalable surface engineering represents significant progress in developing high-performance solid-state lithium metal batteries.展开更多
High-temperature industries,as the primary consumers of energy,are greatly concerned with energy savings.Designing refractory linings with low thermal conductivity to reduce heat dissipation through high-temperature f...High-temperature industries,as the primary consumers of energy,are greatly concerned with energy savings.Designing refractory linings with low thermal conductivity to reduce heat dissipation through high-temperature furnace linings is a critical concern.In this study,a series of novel entropy-stabilized spinel materials are reported,and their potential applications in high-temperature industries are investigated.XRD and TEM results indicate that all materials possess a cubic spinel crystal structure with the■space group.Furthermore,these materials exhibit good phase stability at high temperatures.All entropy-stabilized spinel aggregates demonstrated high refractoriness(>1800℃)and a high load softening temperature(>1700℃).The impact of configurational entropy on the properties of entropy-stabilized spinel materials was also studied.As configurational entropy increased,the thermal conductivity of the entropy-stabilized spinel decreased,while slag corrosion resistance deteriorated.For the entropy-stabilized spinel with a configurational entropy value of 1.126R,it showed good high-temperature stability,reliable resistance to slag attack,and a low thermal conductivity of 2.776 W·m^(-1)·K^(-1)at 1000℃.展开更多
The research on high-performance electromagnetic wave absorption materials with high-temperature and oxidative stability in extreme environments is gaining popularity.Herein,the lightweight silicon carbide nanowires(S...The research on high-performance electromagnetic wave absorption materials with high-temperature and oxidative stability in extreme environments is gaining popularity.Herein,the lightweight silicon carbide nanowires(SiC_(nws))/SiC composites are fabricated with in-situ SiC interface on one-dimensional oriented SiC_(nws)skeleton,which collaborative configuration by 3D printing and freeze casting assembly.The con-structed porous structure optimizes the impedance matching degree and scattering intensity,the maximum effective absorption bandwidth(EAB_(max))of 5.9 GHz and the minimum reflection loss(RL_(min))of−41.4 dB can be realized.Considering the inherent oxidation resistance of SiC,the composites present well-maintained absorption performance at 600℃.Even at 1100℃,the EAB_(max)of 4.9 GHz and RLmin of−30.4 dB also demonstrate the high-temperature absorption stability of the composites,indicating exceptional wave absorption properties and thermal stability.The slight attenuation can be attributed to the decrease in impedance matching capability accompanying the elevated dielectric constant.This work clarifies the impact of structure and component synergy on wave absorption behavior,and offers a novel approach to producing high-performance and high-temperature resistance ceramic-based electromagnetic wave absorption materials suitable for extreme environments.展开更多
Burial dissolution is a critical diagenetic process influencing ultra-deep carbonate reservoir development and preservation.Artificial carbonate samples with different internal structures were prepared,and high-temper...Burial dissolution is a critical diagenetic process influencing ultra-deep carbonate reservoir development and preservation.Artificial carbonate samples with different internal structures were prepared,and high-temperature and highpressure dissolution kinetic simulations were conducted.The results demonstrate that the intensity of burial dissolution is controlled by temperature and pressure,while tectonic-fluid activity influences the development pattern of burial dissolution,ultimately determining the direction of its differential modification.Extensive burial dissolution is likely to occur primarily at relatively shallow depths,significantly influencing reservoir formation,preservation,modification,and adjustment.The development of faults facilitates the maintenance of the intensity of burial dissolution.The maximum intensity of burial dissolution occurs at the tips and overlap zones of faults and intersections of multiple faults.The larger the scale of the faults,the more conducive it is to the development of burial dissolution.Burial dissolution fosters the formation of fault networks characterized by enhanced reservoir capacity and permeability.Burial dissolution controlled by episodic tectonic-fluid activity is a plausible explanation for forming the Tarim Basin's ultra-deep fault-controlled“stringbead-like”reservoirs.展开更多
High-temperature piezoelectric sen-sors are very important in severe environments such as fire safety,aerospace and oil drills,however,most current sensors are not heat res-istant(<300℃)and are fragile,which limit...High-temperature piezoelectric sen-sors are very important in severe environments such as fire safety,aerospace and oil drills,however,most current sensors are not heat res-istant(<300℃)and are fragile,which limits their use,especially in high-temperature environ-ments.A high-temperature resistant flexible piezoelectric film based on graphene oxide(GO)/polyacrylonitrile(PAN)composites was prepared by electrospinning and thermal treat-ment.It was packed into a micro-device,which could work continuously at 500℃.The intro-duction of GO significantly increased the mechanical properties of the PAN nanofibers because the oxygen-containing func-tional groups(electronegative groups)on the surface of the GO initiated a nucleophilic attack on the PAN molecule during heat treatment,enabling the GO to initiate the cyclization of the PAN at lower heat-treatment temperatures.In addition,the abund-ant oxygen-containing functional groups on GO acted as pro-oxidants to hasten the oxidation of PAN during heat treatment.The effects of GO content and heat treatment temperature on the properties of the nanofiber films were investigated.A GO/PAN nanofiber piezoelectric sensor heat-treated at 300℃had a 9.10 V and 2.25μA peak output,which are respectively 101.3%and 78.6%higher than those of the untreated films.Cyclic testing over 5000 cycles at 350℃confirmed the stable out-put performance of the GO/PAN nanofiber piezoelectric sensor.Furthermore,a sensor heat-treated at 400℃had a sensitivity of 1.7 V/N,which is 83.5%higher than that of an untreated one.The results show that the prepared GO/PAN nanofiber piezo-electric sensor combines high temperature resistance,high flexibility,stability and high sensitivity,and may have broad applic-ations in high temperature environments such as the aerospace and petroleum industries.展开更多
Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,a...Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,as well as the wear resistance of the coatings.Besides,the effect of changing the laser melting process on the coatings was also investigated.The oxidation mass gain at 800–1200℃and the high-temperature oxidation behavior during high-temperature treatment for 1 h of two coated Zr alloy samples were studied.Results show that the Co coating and the Co-T800 coating have better resistance against high-temperature oxidation.After oxidizing at 1000℃for 1 h,the thickness of the oxide layer of the uncoated sample was 241.0μm,whereas that of the sample with Co-based coating is only 11.8–35.5μm.The friction wear test shows that the depth of the abrasion mark of the coated sample is only 1/2 of that of the substrate,indicating that the hardness and wear resistance of the Zr substrate are greatly improved.The disadvantage of Co-based coatings is the inferior corrosion resistance in 3.5wt%NaCl solution.展开更多
Powder metallurgy was used to fabricate TiC-NiCr cermets and the oxidation behavior at 900℃ was investigated.Results reveal that TiC-NiCr cermets have uniform structures with excellent mechanical properties,whose har...Powder metallurgy was used to fabricate TiC-NiCr cermets and the oxidation behavior at 900℃ was investigated.Results reveal that TiC-NiCr cermets have uniform structures with excellent mechanical properties,whose hardness is 65 HRC and flexural strength is 1450 MPa.The high-temperature oxidation mechanism of TiC-based cermets was investigated through an X-ray diffractometer and scanning electron microscope.The added elements Ni and Cr along with their solid solutions not only bond with the hard phase TiC to ensure the physical performance of the cermet,but also impede the internal diffusion during oxidation by forming a dense composite oxide layer,thereby enhancing the oxidation resistance.The TiC-NiCr cermet exhibits a dense protective oxide layer at 900℃ and can endure continuous oxidation for approximately 1000 h.A methodology for fabricating TiC-NiCr metal matrix composites is proposed,and their oxidation resistance is evaluated,providing a theoretical and practical basis for simultaneously enhancing the mechanical properties and oxidation resistance and reducing production costs.展开更多
(TiZrHf)_(50)Ni_(30)Cu_(20-x)Co_(x)(x=2,4,6,at%)high-entropy high-temperature shape memory alloys were fabricated by watercooled copper crucible in a magnetic levitation vacuum melting furnace,and the effects of Co co...(TiZrHf)_(50)Ni_(30)Cu_(20-x)Co_(x)(x=2,4,6,at%)high-entropy high-temperature shape memory alloys were fabricated by watercooled copper crucible in a magnetic levitation vacuum melting furnace,and the effects of Co content on microstructure and mechanical properties were investigated.The results indicate that the grain size of the alloy decreases with increasing the Co content.In the as-cast state,the alloy consists primarily of the B19′phase,with a trace of B2 phase.The fracture morphology is predominantly composed of the B19′phase,whereas the B2 phase is nearly absent.Increasing the Co content or reducing the sample dimensions(d)markedly enhance the compressive strength and ductility of the alloy.When d=2 mm,the(TiZrHf)_(50)Ni_(30)Cu_(14)Co_(6) alloy demonstrates the optimal mechanical properties,achieving a compressive strength of 2142.39±1.8 MPa and a plasticity of 17.31±0.3%.The compressive cyclic test shows that with increasing the compressive strain,the residual strain of the(TiZrHf)_(50)Ni_(30)Cu_(14)Co_(6) alloy increases while the recovery ability declines.The superelastic recovery capability of the alloy is continuously enhanced.The superelastic recovery rate increases from 1.36%to 2.12%,the residual strain rate rises from 1.79%to 5.52%,the elastic recovery rate ascends from 3.86%to 7.36%,while the total recovery rate declines from 74.48%to 63.20%.展开更多
To improve the high-temperature oxidation resistance of TiAlNb9 alloy,a Cr-Al-Y co-deposition coating was prepared on the alloy surface by the pack cementation method.The microstructure of the coating was analyzed by ...To improve the high-temperature oxidation resistance of TiAlNb9 alloy,a Cr-Al-Y co-deposition coating was prepared on the alloy surface by the pack cementation method.The microstructure of the coating was analyzed by scanning electron microscope,energy dispersive spectrometer,and X-ray diffractometer,and the high-temperature oxidation properties of the substrate and coating at 1273 K were compared and studied.The results show that the Cr-Al-Y coating is about 30μm in thickness,and it has a dense structure and good film-substrate bonding.The coating includes an outer layer composed of TiCr_(2),TiCr,Ti4Cr,and(Ti,Nb)Cr4 phases as well as an inner layer composed of Ti_(2)Al,and Nb-richγ-TiAl interdiffusion zone.The TiAlNb9 substrate forms an oxide layer composed of TiO2 and Al_(2)O_(3) at 1273 K.Due to its loose and porous structure,TiO2 oxide film cannot effectively isolate the internal diffusion of element O,resulting in continuous oxidation damage to the substrate.The Cr-Al-Y co-deposition coating forms a dense Cr2O3 and Al_(2)O_(3) oxide layer during oxidation,effectively preventing the internal diffusion of element O and significantly improving the high-temperature oxidation resistance of the substrate alloy.展开更多
The austenite(γ)reversely transformed from lath martensite(LM),lath bainite(LB),granular bainite(GB)and pearlite+ferrite(P+F)in a high-strength steel was studied at high temperatures using in-situ electron backscatte...The austenite(γ)reversely transformed from lath martensite(LM),lath bainite(LB),granular bainite(GB)and pearlite+ferrite(P+F)in a high-strength steel was studied at high temperatures using in-situ electron backscatter diffraction(EBSD).The memory effect of initial γ significantly affects the nucleation of the reverted γ in LM and GB structures,while a weak influence on that of LB and P+F structures.This results in a significant difference in γ grain size after complete austenitization,with the first two obtaining larger γ grains while the latter two are relatively small.Crystallographic analysis revealed that the reverted γ with acicular morphology(γA),most of which maintained the same orientation with the prior γ,dominated the reaustenitization behavior of LM and GB structures through preferential nucleation within γ grains and coalesced growth modes.Although globular reverted γ(γ_(G))with random orientation or large deviation from the prior γ can nucleate at the grain boundaries or within the grains,it is difficult for it to grow and play a role in segmenting and refining the prior γ due to the inhibition of γ_(A) coalescing.For LB and P+F structures,the nucleation rate of intragranular γ_(G) increases with increasing temperature,and always shows a random orientation.These γ_(G) grains can coarsen simultaneously with the intergranular γ_(G),ultimately playing a role in jointly dividing and refining the finalγgrains.Research also found that the differences in the effects of four different microstructures on revertedγnucleation are closely related to the variant selection of the matrix structure,as well as the content and size of cementite(θ).High density of block boundaries induced by weakening of variant selection and many fineθformed in the lath are the key to promoting LB structure to obtain more intragranular γ_(G) formation,as well as the important role of the large-sized θ in P+F structure.展开更多
Investigating highly effective electrocatalysts for high-temperature proton exchange membrane fuel cells(HT-PEMFC)requires the resistance to phosphate acid(PA)poisoning at cathodic oxygen reduction reaction(ORR).Recen...Investigating highly effective electrocatalysts for high-temperature proton exchange membrane fuel cells(HT-PEMFC)requires the resistance to phosphate acid(PA)poisoning at cathodic oxygen reduction reaction(ORR).Recent advancements in catalysts have focused on alleviating phosphoric anion adsorption on Pt-based catalysts with modified electronic structure or catalytic interface and developing Fe-N-C based catalysts with immunity of PA poisoning.Fe-N-C-based catalysts have emerged as promising alternatives to Pt-based catalysts,offering significant potential to overcome the characteristic adsorption of phosphate anion on Pt.An overview of these developments provides insights into catalytic mechanisms and facilitates the design of more efficient catalysts.This review begins with an exploration of basic poisoning principles,followed by a critical summary of characterization techniques employed to identified the underlying mechanism of poisoning effect.Attention is then directed to endeavors aimed at enhancing the HT-PEMFC performance by well-designed catalysts.Finally,the opportunities and challenges in developing the anti-PA poisoning strategy and practical HT-PEMFC is discussed.Through these discussions,a comprehensive understanding of PA-poisoning bottlenecks and inspire future research directions is aim to provided.展开更多
As the global exploration and development of oil and gas resources advances into deep formations,the harsh conditions of high temperature and high salinity present significant challenges for drilling fluids.In order t...As the global exploration and development of oil and gas resources advances into deep formations,the harsh conditions of high temperature and high salinity present significant challenges for drilling fluids.In order to address the technical difficulties associated with the failure of filtrate loss reducers under high-temperature and high-salinity conditions.In this study,a hydrophobic zwitterionic filtrate loss reducer(PDA)was synthesized based on N,N-dimethylacrylamide(DMAA),2-acrylamido-2-methylpropane sulfonic acid(AMPS),diallyl dimethyl ammonium chloride(DMDAAC),styrene(ST)and a specialty vinyl monomer(A1).When the concentration of PDA was 3%,the FLAPI of PDA-WBDF was 9.8 mL and the FLHTHP(180℃,3.5 MPa)was 37.8 mL after aging at 240℃for 16 h.In the saturated NaCl environment,the FLAPI of PDA-SWBDF was 4.0 mL and the FLHTHP(180℃,3.5 MPa)was 32.0 mL after aging at 220℃ for 16 h.Under high-temperature and high-salinity conditions,the combined effect of anti-polyelectrolyte and hydrophobic association allowed PDA to adsorb on the bentonite surface tightly.The sulfonic acid groups of PDA increased the negative electronegativity and the hydration film thickness on bentonite surface,which enhanced the colloidal stability,maintained the flattened lamellar structure of bentonite and formed an appropriate particle size distribution,resulting in the formation of dense mud cakes and reducing the filtration loss effectively.展开更多
The Al-Cu alloy is a historical model alloy system in the physical metallurgy of engineering aluminum al-loys.Nevertheless,a few fundamental phenomena of phase transformation occurring in this simple alloy are still n...The Al-Cu alloy is a historical model alloy system in the physical metallurgy of engineering aluminum al-loys.Nevertheless,a few fundamental phenomena of phase transformation occurring in this simple alloy are still not adequately understood.Among all,for instance,the formation mechanisms of its key harden-ingθ'-phase remain mysterious.There is strong evidence thatθ'-precipitates can form from a different high-temperature precipitation pathway,while their formation mechanism via the conventional pathway well-known since 1938 remains to be clarified.Using state-of-the-art electron microscopy,here we report a secondary high-temperature precipitation pathway ofθ'-precipitates.It is demonstrated that led by a secondary high-temperature precursor,namedθ'_(S-HTP),very fineθ'-precipitates can form in the unde-formed bulk Al-Cu alloys at elevated temperatures(≥250℃).Interestingly is that with Sc-microalloying the surviving rate of meta-stableθ'_(S-HTP) precipitates increases drastically and the formedθ'-precipitates become much finer,significantly enhancing the alloys’strength and thermal stability.It is also revealed that aθ'_(S-HTP) precipitate can genetically evolve into aθ'-precipitate without having to change its mor-phology and orientation.Our study provides new insights into understanding the industry bulk alloys’microstructures and properties.展开更多
Considering the fracture problem of the silica-based ceramic core in the integrated casting of hollow turbine blades during directional solidification,the influence of various whiskers,including silicon carbide whiske...Considering the fracture problem of the silica-based ceramic core in the integrated casting of hollow turbine blades during directional solidification,the influence of various whiskers,including silicon carbide whiskers,silicon nitride whiskers,and mullite whiskers,on the high-temperature strength of the silica-based ceramic core was investigated.Additionally,the formation of microstructure morphology and phase structure was analyzed.Research results show that silicon carbide whiskers can reduce the microcracks caused by the shrinkage of cristobalite.During the sintering process,some of the silicon carbide whiskers oxidize and react with aluminum powder to form mullite,which can improve the high-temperature strength of the ceramic cores.When the content of silicon carbide whiskers is 3wt.%,the high-temperature bending strength of the cores reaches the maximum value of 21 MPa.Silicon nitride whiskers decompose in a high-temperature environment and react with aluminum powder in the matrix material to form mullite whiskers.When the content of silicon nitride whiskers is 5wt.%,the high-temperature bending strength of the cores reaches 20 MPa.By adding mullite whiskers,a structure of cristobalite wrapped mullite whiskers can be formed to achieve toughening.When the content of mullite whiskers is 4wt.%,the high-temperature bending strength can reach 17.2 MPa.By comparing the performance of silicon carbide whiskers,silicon nitride whiskers,and mullite whiskers,along with conducting slurry viscosity tests and casting experiments,it is determined that a ceramic slurry containing 4wt.%mullite whiskers is the most suitable for making the cores used in the integrated casting of hollow turbine blades.展开更多
The high-temperature mechanical behaviors of Multi-Layer Composite Panels(MCP)and Corrugated Sandwich Panels(CSP)of Continuous Glass Fiber-Reinforced Polypropylene(CGFRPP)are critical for their application in aerospac...The high-temperature mechanical behaviors of Multi-Layer Composite Panels(MCP)and Corrugated Sandwich Panels(CSP)of Continuous Glass Fiber-Reinforced Polypropylene(CGFRPP)are critical for their application in aerospace fields,which have been rarely mentioned in previous studies.High-temperature quasi-static tensile and compression tests on CGFRPP MCP are conducted first.The results showed that the tensile and compression strength,stiffness,and tensile modulus of MCP decreased with increasing temperature.The Gibson model was found to be more suitable for predicting the high-temperature mechanical performance of MCP after comparing the calculated results of different theoretical models with experimental data.Secondly,hightemperature planar compression tests were conducted on the CGFRPP CSP,revealing that the main failure modes were corrugated core buckling and delamination between the face panel and core material,with delamination being intensified at higher temperatures.Therefore,we proposed a strength theoretical model that considers structural buckling failure and interface delamination failure,and introduced the influence factor to evaluate the effect of interface delamination on structural strength.展开更多
To understand the applicability of high-temperature preformed particle gel(HT-PPG)for control of short-circuiting in enhanced geothermal systems(EGSs),core flooding experiments were conducted on fractured granite core...To understand the applicability of high-temperature preformed particle gel(HT-PPG)for control of short-circuiting in enhanced geothermal systems(EGSs),core flooding experiments were conducted on fractured granite cores under varying fracture widths,gel particle sizes and swelling ratios.Key parameters such as injection pressure,water breakthrough pressure,and residual resistance factor were measured to evaluate HT-PPG performance.The gel exhibited strong injectability,entering granite fractures at pressure gradients as low as 0.656 MPa/m;HT-PPG yields a superior sealing performance by significantly reducing the permeability;and dehydration occurs during HT-PPG propagation,with a dehydration ratio ranging from 4.71%to 11.36%.This study reveals that HT-PPG can be injected into geothermal formations with minimal pressure yet provides strong resistance to breakthrough once in place.This balance of injectability and sealing strength makes HT-PPG effective for addressing thermal short-circuiting in EGS reservoirs.展开更多
By using fatigue crack propagation testing and microstructural characterization,the crack fracture and propagation mechanisms of K4169 superalloy under various loads were investigated.The results demonstrate that the ...By using fatigue crack propagation testing and microstructural characterization,the crack fracture and propagation mechanisms of K4169 superalloy under various loads were investigated.The results demonstrate that the grain sizes of K4169 superalloy significantly increase,and the precipitation of the needle-likeδphase and the Laves phase is observed.Voids and microcracks form at location of Laves phase enrichment,creating conditions for crack propagation.By the a−N(a is the crack length,and N is the number of cycles)relationship curve,the change in the fatigue crack growth rate with the increasing number of cycles progresses through three separate stages.The fracture process of K4169 superalloy under low-stress cyclic loading(3 kN)exhibits the ductile fracture.Subsequently,the fracture process starts to change from the ductile fracture to the brittle fracture as the stress increases to 4.5 kN.In the microstructures of fractures in both stress states,intergranular propagation is the mechanism responsible for crack propagation.Moreover,the Laves phase exists near the fracture crack,which is in line with the post-service structural phenomenon.展开更多
Traditionally,the construction of stable interphases relies on solvent structures dominated by aggregated anionic structures(AGG/AGG+).Nonetheless,we find that the construction of stable interphases in hightemperature...Traditionally,the construction of stable interphases relies on solvent structures dominated by aggregated anionic structures(AGG/AGG+).Nonetheless,we find that the construction of stable interphases in hightemperature environments is based on contact ion pairs(CIPs)dominated solvation structure here.In detail,in the long-chain phosphate ester-based electrolyte,the spatial site-blocking effect enables the strong solvation co-solvent ether(diethylene glycol dimethyl ether,G2)to exhibit strong ion-dipole interactions,further multicomponent competitive coordination maintaining the CIP,balancing electrode kinetics,and optimizing the high-temperature interphases.High-temperature in-situ Raman spectroscopy monitors the changes in the stable solvent structure during charge/discharge processes for the first time,and time of flight secondary ion mass spectrometry(TOF-SIMS)reveals the stable solid electrolyte interphase(SEI)with full-depth enrichment of the inorganic component.Benefiting from the high-temperature interfacial chemistry-dependent solvent structure,the advanced electrolyte enables stable cycling of 1.6 Ah 18650 batterie at 100-125℃and discharging with high current pulses(~1.83 A)at 150℃,which has rarely been reported so far.In addition,pin-pricking of 18650 batteries at100%state of charge(SoC)without fire or smoke and the moderate thermal runaway temperature(187℃)tested via the accelerating rate calorimetry(ARC)demonstrate the excellent safety of the optimized electrolyte.展开更多
基金supported by the National Natural Science Foundation of China(Nos.52174175 and 52274078)the Program for the Scientific and Technological Innovation Team in Universities of Henan Province(No.23IRTSTHN005)。
文摘The tensile strength of rocks under real-time high-temperatures is essential for enhanced geothermal system development.However,the complex occurrence and deep burial of hot dry rocks limit the quantity and quality of standard samples for mechanical testing.This paper compared the tensile strengths obtained from Brazilian splitting tests on standard samples(with a diameter of 50 mm and a thickness of 25 mm)and micro-tensile samples(with a diameter of 50 mm and a thickness of 25 mm)of two types of granites.A power-law size effect model was established between the two sets of data,validating the reliability of the testing method.Then,miniature Brazilian splitting under real-time high-temperature,combined with X-ray diffraction(XRD)revealed temperature-dependent strength variations and microstructural damage mechanisms.The results show that:(1)The comparison error between the tensile strength obtained by the fitting model and that of the measured standard samples was less than 6%.(2)In real-time high-temperature conditions,tensile strength of granite exhibited non-monotonic behavior,increasing below 300°C before decreasing,with sharp declines at 400–500°C and 600–700°C.(3)Thermal damage stems from the differences in the high-temperature behavior of minerals,including dehydration,phase transformation,and differential expansion.
文摘This study investigated the physicochemical properties,enzyme activities,volatile flavor components,microbial communities,and sensory evaluation of high-temperature Daqu(HTD)during the maturation process,and a standard system was established for comprehensive quality evaluation of HTD.There were obvious changes in the physicochemical properties,enzyme activities,and volatile flavor components at different storage periods,which affected the sensory evaluation of HTD to a certain extent.The results of high-throughput sequencing revealed significant microbial diversity,and showed that the bacterial community changed significantly more than did the fungal community.During the storage process,the dominant bacterial genera were Kroppenstedtia and Thermoascus.The correlation between dominant microorganisms and quality indicators highlighted their role in HTD quality.Lactococcus,Candida,Pichia,Paecilomyces,and protease activity played a crucial role in the formation of isovaleraldehyde.Acidic protease activity had the greatest impact on the microbial community.Moisture promoted isobutyric acid generation.Furthermore,the comprehensive quality evaluation standard system was established by the entropy weight method combined with multi-factor fuzzy mathematics.Consequently,this study provides innovative insights for comprehensive quality evaluation of HTD during storage and establishes a groundwork for scientific and rational storage of HTD and quality control of sauce-flavor Baijiu.
基金financially supported by the National Natural Science Foundation of China(Nos.22102212 and 22479067).
文摘High-nickel ternary cathodes hold a great application prospect in solid-state lithium metal batteries to achieve high-energy density,but they still suffer from structural instability and detrimental side reactions with the solid-state electrolytes.To circumvent these issues,a continuous uniform layer polyacrylonitrile(PAN)was introduced on the surface of LiNi_(0.8)Mn_(0.1)Co_(0.1)O_(2) via in situ polymerization of acrylonitrile(AN).Furthermore,the partial-cyclized treatment of PAN(cPAN)coating layer presents high ionic and electron conductivity,which can accelerate interfacial Li+and electron diffusion simultaneously.And the thermodynamically stabilized cPAN coating layer cannot only effectively inhibit detrimental side reactions between cathode and solid-state electrolytes but also provide a homogeneous stress to simultaneously address the problems of bulk structural degradation,which contributes to the exceptional mechanical and electrochemical stabilities of the modified electrode.Besides,the coordination bond interaction between the cPAN and NCM811 can suppress the migration of Ni to elevate the stability of the crystal structure.Benefited from these,the In-cPAN-260@NCM811 shows excellent cycling performance with a retention of 86.8%after 300 cycles and superior rate capability.And endow the solid-state battery with thermal safety stability even at hightemperature extreme environment.This facile and scalable surface engineering represents significant progress in developing high-performance solid-state lithium metal batteries.
基金financially supported by the National Natural Science Foundation of China(Nos.52472032 and 52172023)the Key Program of Natural Science Foundation of Hubei Province(No.2024AFA083)
文摘High-temperature industries,as the primary consumers of energy,are greatly concerned with energy savings.Designing refractory linings with low thermal conductivity to reduce heat dissipation through high-temperature furnace linings is a critical concern.In this study,a series of novel entropy-stabilized spinel materials are reported,and their potential applications in high-temperature industries are investigated.XRD and TEM results indicate that all materials possess a cubic spinel crystal structure with the■space group.Furthermore,these materials exhibit good phase stability at high temperatures.All entropy-stabilized spinel aggregates demonstrated high refractoriness(>1800℃)and a high load softening temperature(>1700℃).The impact of configurational entropy on the properties of entropy-stabilized spinel materials was also studied.As configurational entropy increased,the thermal conductivity of the entropy-stabilized spinel decreased,while slag corrosion resistance deteriorated.For the entropy-stabilized spinel with a configurational entropy value of 1.126R,it showed good high-temperature stability,reliable resistance to slag attack,and a low thermal conductivity of 2.776 W·m^(-1)·K^(-1)at 1000℃.
基金supported by the National Key R&D Program of China(No.2022YFB3707700)National Natural Science Foundation of China(No.52302121)+3 种基金Shanghai Sailing Program(No.23YF1454700)Shanghai Natural Science Foundation(No.23ZR1472700)Shanghai Post-doctoral Excellent Program(No.2022664)Shanghai Science and Technology Innovation Action Plan(No.21511104800).
文摘The research on high-performance electromagnetic wave absorption materials with high-temperature and oxidative stability in extreme environments is gaining popularity.Herein,the lightweight silicon carbide nanowires(SiC_(nws))/SiC composites are fabricated with in-situ SiC interface on one-dimensional oriented SiC_(nws)skeleton,which collaborative configuration by 3D printing and freeze casting assembly.The con-structed porous structure optimizes the impedance matching degree and scattering intensity,the maximum effective absorption bandwidth(EAB_(max))of 5.9 GHz and the minimum reflection loss(RL_(min))of−41.4 dB can be realized.Considering the inherent oxidation resistance of SiC,the composites present well-maintained absorption performance at 600℃.Even at 1100℃,the EAB_(max)of 4.9 GHz and RLmin of−30.4 dB also demonstrate the high-temperature absorption stability of the composites,indicating exceptional wave absorption properties and thermal stability.The slight attenuation can be attributed to the decrease in impedance matching capability accompanying the elevated dielectric constant.This work clarifies the impact of structure and component synergy on wave absorption behavior,and offers a novel approach to producing high-performance and high-temperature resistance ceramic-based electromagnetic wave absorption materials suitable for extreme environments.
基金supported by the National Natural Science Foundation of China(Grant No.U21B2062)supported by the Key Laboratory for Carbonate Reservoirs of China National Petroleum Corporation。
文摘Burial dissolution is a critical diagenetic process influencing ultra-deep carbonate reservoir development and preservation.Artificial carbonate samples with different internal structures were prepared,and high-temperature and highpressure dissolution kinetic simulations were conducted.The results demonstrate that the intensity of burial dissolution is controlled by temperature and pressure,while tectonic-fluid activity influences the development pattern of burial dissolution,ultimately determining the direction of its differential modification.Extensive burial dissolution is likely to occur primarily at relatively shallow depths,significantly influencing reservoir formation,preservation,modification,and adjustment.The development of faults facilitates the maintenance of the intensity of burial dissolution.The maximum intensity of burial dissolution occurs at the tips and overlap zones of faults and intersections of multiple faults.The larger the scale of the faults,the more conducive it is to the development of burial dissolution.Burial dissolution fosters the formation of fault networks characterized by enhanced reservoir capacity and permeability.Burial dissolution controlled by episodic tectonic-fluid activity is a plausible explanation for forming the Tarim Basin's ultra-deep fault-controlled“stringbead-like”reservoirs.
文摘High-temperature piezoelectric sen-sors are very important in severe environments such as fire safety,aerospace and oil drills,however,most current sensors are not heat res-istant(<300℃)and are fragile,which limits their use,especially in high-temperature environ-ments.A high-temperature resistant flexible piezoelectric film based on graphene oxide(GO)/polyacrylonitrile(PAN)composites was prepared by electrospinning and thermal treat-ment.It was packed into a micro-device,which could work continuously at 500℃.The intro-duction of GO significantly increased the mechanical properties of the PAN nanofibers because the oxygen-containing func-tional groups(electronegative groups)on the surface of the GO initiated a nucleophilic attack on the PAN molecule during heat treatment,enabling the GO to initiate the cyclization of the PAN at lower heat-treatment temperatures.In addition,the abund-ant oxygen-containing functional groups on GO acted as pro-oxidants to hasten the oxidation of PAN during heat treatment.The effects of GO content and heat treatment temperature on the properties of the nanofiber films were investigated.A GO/PAN nanofiber piezoelectric sensor heat-treated at 300℃had a 9.10 V and 2.25μA peak output,which are respectively 101.3%and 78.6%higher than those of the untreated films.Cyclic testing over 5000 cycles at 350℃confirmed the stable out-put performance of the GO/PAN nanofiber piezoelectric sensor.Furthermore,a sensor heat-treated at 400℃had a sensitivity of 1.7 V/N,which is 83.5%higher than that of an untreated one.The results show that the prepared GO/PAN nanofiber piezo-electric sensor combines high temperature resistance,high flexibility,stability and high sensitivity,and may have broad applic-ations in high temperature environments such as the aerospace and petroleum industries.
基金National Natural Science Foundation of China(52071126)Natural Science Foundation of Tianjin City,China(22JCQNJC01240)+2 种基金Central Guidance on Local Science and Technology Development Fund of Hebei Province(226Z1009G)Special Funds for Science and Technology Innovation in Hebei(2022X19)Anhui Provincial Natural Science Foundation(2308085ME135)。
文摘Co-based alloy coating was prepared on Zr alloy using laser melting and cladding technique to study the difference in the high-temperature oxidation behavior between pure metal Co coatings and Co-T800 alloy coatings,as well as the wear resistance of the coatings.Besides,the effect of changing the laser melting process on the coatings was also investigated.The oxidation mass gain at 800–1200℃and the high-temperature oxidation behavior during high-temperature treatment for 1 h of two coated Zr alloy samples were studied.Results show that the Co coating and the Co-T800 coating have better resistance against high-temperature oxidation.After oxidizing at 1000℃for 1 h,the thickness of the oxide layer of the uncoated sample was 241.0μm,whereas that of the sample with Co-based coating is only 11.8–35.5μm.The friction wear test shows that the depth of the abrasion mark of the coated sample is only 1/2 of that of the substrate,indicating that the hardness and wear resistance of the Zr substrate are greatly improved.The disadvantage of Co-based coatings is the inferior corrosion resistance in 3.5wt%NaCl solution.
基金National Natural Science Foundation of China(52376076)Open Fund of Material Corrosion and Protection Key Laboratory of Sichuan Province(2023CL13)Laiwu Vocational and Technical College Teachers Research Fund(2023jsky05)。
文摘Powder metallurgy was used to fabricate TiC-NiCr cermets and the oxidation behavior at 900℃ was investigated.Results reveal that TiC-NiCr cermets have uniform structures with excellent mechanical properties,whose hardness is 65 HRC and flexural strength is 1450 MPa.The high-temperature oxidation mechanism of TiC-based cermets was investigated through an X-ray diffractometer and scanning electron microscope.The added elements Ni and Cr along with their solid solutions not only bond with the hard phase TiC to ensure the physical performance of the cermet,but also impede the internal diffusion during oxidation by forming a dense composite oxide layer,thereby enhancing the oxidation resistance.The TiC-NiCr cermet exhibits a dense protective oxide layer at 900℃ and can endure continuous oxidation for approximately 1000 h.A methodology for fabricating TiC-NiCr metal matrix composites is proposed,and their oxidation resistance is evaluated,providing a theoretical and practical basis for simultaneously enhancing the mechanical properties and oxidation resistance and reducing production costs.
基金National Natural Science Foundation of China(12404230,52061027)Science and Technology Program Project of Gansu Province(22YF7GA155)+1 种基金Lanzhou Youth Science and Technology Talent Innovation Project(2023-QN-91)Zhejiang Provincial Natural Science Foundation of China(LY23E010002)。
文摘(TiZrHf)_(50)Ni_(30)Cu_(20-x)Co_(x)(x=2,4,6,at%)high-entropy high-temperature shape memory alloys were fabricated by watercooled copper crucible in a magnetic levitation vacuum melting furnace,and the effects of Co content on microstructure and mechanical properties were investigated.The results indicate that the grain size of the alloy decreases with increasing the Co content.In the as-cast state,the alloy consists primarily of the B19′phase,with a trace of B2 phase.The fracture morphology is predominantly composed of the B19′phase,whereas the B2 phase is nearly absent.Increasing the Co content or reducing the sample dimensions(d)markedly enhance the compressive strength and ductility of the alloy.When d=2 mm,the(TiZrHf)_(50)Ni_(30)Cu_(14)Co_(6) alloy demonstrates the optimal mechanical properties,achieving a compressive strength of 2142.39±1.8 MPa and a plasticity of 17.31±0.3%.The compressive cyclic test shows that with increasing the compressive strain,the residual strain of the(TiZrHf)_(50)Ni_(30)Cu_(14)Co_(6) alloy increases while the recovery ability declines.The superelastic recovery capability of the alloy is continuously enhanced.The superelastic recovery rate increases from 1.36%to 2.12%,the residual strain rate rises from 1.79%to 5.52%,the elastic recovery rate ascends from 3.86%to 7.36%,while the total recovery rate declines from 74.48%to 63.20%.
基金National Natural Science Foundation of China(52161009)Innovation Project of Postgraduate Students in North Minzu University(YCX24104)。
文摘To improve the high-temperature oxidation resistance of TiAlNb9 alloy,a Cr-Al-Y co-deposition coating was prepared on the alloy surface by the pack cementation method.The microstructure of the coating was analyzed by scanning electron microscope,energy dispersive spectrometer,and X-ray diffractometer,and the high-temperature oxidation properties of the substrate and coating at 1273 K were compared and studied.The results show that the Cr-Al-Y coating is about 30μm in thickness,and it has a dense structure and good film-substrate bonding.The coating includes an outer layer composed of TiCr_(2),TiCr,Ti4Cr,and(Ti,Nb)Cr4 phases as well as an inner layer composed of Ti_(2)Al,and Nb-richγ-TiAl interdiffusion zone.The TiAlNb9 substrate forms an oxide layer composed of TiO2 and Al_(2)O_(3) at 1273 K.Due to its loose and porous structure,TiO2 oxide film cannot effectively isolate the internal diffusion of element O,resulting in continuous oxidation damage to the substrate.The Cr-Al-Y co-deposition coating forms a dense Cr2O3 and Al_(2)O_(3) oxide layer during oxidation,effectively preventing the internal diffusion of element O and significantly improving the high-temperature oxidation resistance of the substrate alloy.
基金financially supported by the National Natural Science Foundation of China(Nos.52271089 and 52001023)the Basic Research and Application Basic Research Foundation of Guangdong Province(Nos.2022A1515240016 and 2023B1515250006)the Fundamental Research Funds for the Central Universities(No.FRF-BD-23-01).
文摘The austenite(γ)reversely transformed from lath martensite(LM),lath bainite(LB),granular bainite(GB)and pearlite+ferrite(P+F)in a high-strength steel was studied at high temperatures using in-situ electron backscatter diffraction(EBSD).The memory effect of initial γ significantly affects the nucleation of the reverted γ in LM and GB structures,while a weak influence on that of LB and P+F structures.This results in a significant difference in γ grain size after complete austenitization,with the first two obtaining larger γ grains while the latter two are relatively small.Crystallographic analysis revealed that the reverted γ with acicular morphology(γA),most of which maintained the same orientation with the prior γ,dominated the reaustenitization behavior of LM and GB structures through preferential nucleation within γ grains and coalesced growth modes.Although globular reverted γ(γ_(G))with random orientation or large deviation from the prior γ can nucleate at the grain boundaries or within the grains,it is difficult for it to grow and play a role in segmenting and refining the prior γ due to the inhibition of γ_(A) coalescing.For LB and P+F structures,the nucleation rate of intragranular γ_(G) increases with increasing temperature,and always shows a random orientation.These γ_(G) grains can coarsen simultaneously with the intergranular γ_(G),ultimately playing a role in jointly dividing and refining the finalγgrains.Research also found that the differences in the effects of four different microstructures on revertedγnucleation are closely related to the variant selection of the matrix structure,as well as the content and size of cementite(θ).High density of block boundaries induced by weakening of variant selection and many fineθformed in the lath are the key to promoting LB structure to obtain more intragranular γ_(G) formation,as well as the important role of the large-sized θ in P+F structure.
文摘Investigating highly effective electrocatalysts for high-temperature proton exchange membrane fuel cells(HT-PEMFC)requires the resistance to phosphate acid(PA)poisoning at cathodic oxygen reduction reaction(ORR).Recent advancements in catalysts have focused on alleviating phosphoric anion adsorption on Pt-based catalysts with modified electronic structure or catalytic interface and developing Fe-N-C based catalysts with immunity of PA poisoning.Fe-N-C-based catalysts have emerged as promising alternatives to Pt-based catalysts,offering significant potential to overcome the characteristic adsorption of phosphate anion on Pt.An overview of these developments provides insights into catalytic mechanisms and facilitates the design of more efficient catalysts.This review begins with an exploration of basic poisoning principles,followed by a critical summary of characterization techniques employed to identified the underlying mechanism of poisoning effect.Attention is then directed to endeavors aimed at enhancing the HT-PEMFC performance by well-designed catalysts.Finally,the opportunities and challenges in developing the anti-PA poisoning strategy and practical HT-PEMFC is discussed.Through these discussions,a comprehensive understanding of PA-poisoning bottlenecks and inspire future research directions is aim to provided.
基金supported by State Key Laboratory of Deep Oil and Gas(No.SKLDOG2024-ZYRC-03)supported by the Excellent Young Scientists Fund of the National Natural Science Foundation of China(No.52322401)the National Natural Science Foundation of China(52288101).
文摘As the global exploration and development of oil and gas resources advances into deep formations,the harsh conditions of high temperature and high salinity present significant challenges for drilling fluids.In order to address the technical difficulties associated with the failure of filtrate loss reducers under high-temperature and high-salinity conditions.In this study,a hydrophobic zwitterionic filtrate loss reducer(PDA)was synthesized based on N,N-dimethylacrylamide(DMAA),2-acrylamido-2-methylpropane sulfonic acid(AMPS),diallyl dimethyl ammonium chloride(DMDAAC),styrene(ST)and a specialty vinyl monomer(A1).When the concentration of PDA was 3%,the FLAPI of PDA-WBDF was 9.8 mL and the FLHTHP(180℃,3.5 MPa)was 37.8 mL after aging at 240℃for 16 h.In the saturated NaCl environment,the FLAPI of PDA-SWBDF was 4.0 mL and the FLHTHP(180℃,3.5 MPa)was 32.0 mL after aging at 220℃ for 16 h.Under high-temperature and high-salinity conditions,the combined effect of anti-polyelectrolyte and hydrophobic association allowed PDA to adsorb on the bentonite surface tightly.The sulfonic acid groups of PDA increased the negative electronegativity and the hydration film thickness on bentonite surface,which enhanced the colloidal stability,maintained the flattened lamellar structure of bentonite and formed an appropriate particle size distribution,resulting in the formation of dense mud cakes and reducing the filtration loss effectively.
基金supported by the National Natural Science Foundation of China(Nos.51831004 and 52171006).
文摘The Al-Cu alloy is a historical model alloy system in the physical metallurgy of engineering aluminum al-loys.Nevertheless,a few fundamental phenomena of phase transformation occurring in this simple alloy are still not adequately understood.Among all,for instance,the formation mechanisms of its key harden-ingθ'-phase remain mysterious.There is strong evidence thatθ'-precipitates can form from a different high-temperature precipitation pathway,while their formation mechanism via the conventional pathway well-known since 1938 remains to be clarified.Using state-of-the-art electron microscopy,here we report a secondary high-temperature precipitation pathway ofθ'-precipitates.It is demonstrated that led by a secondary high-temperature precursor,namedθ'_(S-HTP),very fineθ'-precipitates can form in the unde-formed bulk Al-Cu alloys at elevated temperatures(≥250℃).Interestingly is that with Sc-microalloying the surviving rate of meta-stableθ'_(S-HTP) precipitates increases drastically and the formedθ'-precipitates become much finer,significantly enhancing the alloys’strength and thermal stability.It is also revealed that aθ'_(S-HTP) precipitate can genetically evolve into aθ'-precipitate without having to change its mor-phology and orientation.Our study provides new insights into understanding the industry bulk alloys’microstructures and properties.
文摘Considering the fracture problem of the silica-based ceramic core in the integrated casting of hollow turbine blades during directional solidification,the influence of various whiskers,including silicon carbide whiskers,silicon nitride whiskers,and mullite whiskers,on the high-temperature strength of the silica-based ceramic core was investigated.Additionally,the formation of microstructure morphology and phase structure was analyzed.Research results show that silicon carbide whiskers can reduce the microcracks caused by the shrinkage of cristobalite.During the sintering process,some of the silicon carbide whiskers oxidize and react with aluminum powder to form mullite,which can improve the high-temperature strength of the ceramic cores.When the content of silicon carbide whiskers is 3wt.%,the high-temperature bending strength of the cores reaches the maximum value of 21 MPa.Silicon nitride whiskers decompose in a high-temperature environment and react with aluminum powder in the matrix material to form mullite whiskers.When the content of silicon nitride whiskers is 5wt.%,the high-temperature bending strength of the cores reaches 20 MPa.By adding mullite whiskers,a structure of cristobalite wrapped mullite whiskers can be formed to achieve toughening.When the content of mullite whiskers is 4wt.%,the high-temperature bending strength can reach 17.2 MPa.By comparing the performance of silicon carbide whiskers,silicon nitride whiskers,and mullite whiskers,along with conducting slurry viscosity tests and casting experiments,it is determined that a ceramic slurry containing 4wt.%mullite whiskers is the most suitable for making the cores used in the integrated casting of hollow turbine blades.
基金co-supported by the National Natural Science Foundation of China(Nos.12372127,12202085,12302464)the Fundamental Research Funds for the Central Universities,China(No.2024CDJXY009)+1 种基金the Chongqing Outstanding Youth Fund,China(No.CSTB2024NSCQ-JQX0028)the Chongqing Natural Science Foundation,China(Nos.cstc2021ycjh-bgzxm0117,CSTB2022NSCQ-MSX0608)。
文摘The high-temperature mechanical behaviors of Multi-Layer Composite Panels(MCP)and Corrugated Sandwich Panels(CSP)of Continuous Glass Fiber-Reinforced Polypropylene(CGFRPP)are critical for their application in aerospace fields,which have been rarely mentioned in previous studies.High-temperature quasi-static tensile and compression tests on CGFRPP MCP are conducted first.The results showed that the tensile and compression strength,stiffness,and tensile modulus of MCP decreased with increasing temperature.The Gibson model was found to be more suitable for predicting the high-temperature mechanical performance of MCP after comparing the calculated results of different theoretical models with experimental data.Secondly,hightemperature planar compression tests were conducted on the CGFRPP CSP,revealing that the main failure modes were corrugated core buckling and delamination between the face panel and core material,with delamination being intensified at higher temperatures.Therefore,we proposed a strength theoretical model that considers structural buckling failure and interface delamination failure,and introduced the influence factor to evaluate the effect of interface delamination on structural strength.
基金Supported by the U.S.Department of Energy’s Office of Energy Efficiency and Renewable Energy(EERE)under the Geothermal Technologies Office(GTO)“Innovative Methods to Control Hydraulic Properties of Enhanced Geothermal Systems”(DE-EE0009790).
文摘To understand the applicability of high-temperature preformed particle gel(HT-PPG)for control of short-circuiting in enhanced geothermal systems(EGSs),core flooding experiments were conducted on fractured granite cores under varying fracture widths,gel particle sizes and swelling ratios.Key parameters such as injection pressure,water breakthrough pressure,and residual resistance factor were measured to evaluate HT-PPG performance.The gel exhibited strong injectability,entering granite fractures at pressure gradients as low as 0.656 MPa/m;HT-PPG yields a superior sealing performance by significantly reducing the permeability;and dehydration occurs during HT-PPG propagation,with a dehydration ratio ranging from 4.71%to 11.36%.This study reveals that HT-PPG can be injected into geothermal formations with minimal pressure yet provides strong resistance to breakthrough once in place.This balance of injectability and sealing strength makes HT-PPG effective for addressing thermal short-circuiting in EGS reservoirs.
基金National Natural Science Foundation of China (No. 51975200)Hunan Provincial Innovation Foundation for Postgraduate,China (No. QL20220201)。
文摘By using fatigue crack propagation testing and microstructural characterization,the crack fracture and propagation mechanisms of K4169 superalloy under various loads were investigated.The results demonstrate that the grain sizes of K4169 superalloy significantly increase,and the precipitation of the needle-likeδphase and the Laves phase is observed.Voids and microcracks form at location of Laves phase enrichment,creating conditions for crack propagation.By the a−N(a is the crack length,and N is the number of cycles)relationship curve,the change in the fatigue crack growth rate with the increasing number of cycles progresses through three separate stages.The fracture process of K4169 superalloy under low-stress cyclic loading(3 kN)exhibits the ductile fracture.Subsequently,the fracture process starts to change from the ductile fracture to the brittle fracture as the stress increases to 4.5 kN.In the microstructures of fractures in both stress states,intergranular propagation is the mechanism responsible for crack propagation.Moreover,the Laves phase exists near the fracture crack,which is in line with the post-service structural phenomenon.
基金supported by the National Natural Science Foundation of China(grant no.52072322,52202235)the Department of Science and Technology of Sichuan Province(CN)(grant no.23GJHZ0147)the Research and Innovation Fund for Graduate Students of Southwest Petroleum University(No.:2022KYCX111)。
文摘Traditionally,the construction of stable interphases relies on solvent structures dominated by aggregated anionic structures(AGG/AGG+).Nonetheless,we find that the construction of stable interphases in hightemperature environments is based on contact ion pairs(CIPs)dominated solvation structure here.In detail,in the long-chain phosphate ester-based electrolyte,the spatial site-blocking effect enables the strong solvation co-solvent ether(diethylene glycol dimethyl ether,G2)to exhibit strong ion-dipole interactions,further multicomponent competitive coordination maintaining the CIP,balancing electrode kinetics,and optimizing the high-temperature interphases.High-temperature in-situ Raman spectroscopy monitors the changes in the stable solvent structure during charge/discharge processes for the first time,and time of flight secondary ion mass spectrometry(TOF-SIMS)reveals the stable solid electrolyte interphase(SEI)with full-depth enrichment of the inorganic component.Benefiting from the high-temperature interfacial chemistry-dependent solvent structure,the advanced electrolyte enables stable cycling of 1.6 Ah 18650 batterie at 100-125℃and discharging with high current pulses(~1.83 A)at 150℃,which has rarely been reported so far.In addition,pin-pricking of 18650 batteries at100%state of charge(SoC)without fire or smoke and the moderate thermal runaway temperature(187℃)tested via the accelerating rate calorimetry(ARC)demonstrate the excellent safety of the optimized electrolyte.
