This study develops a surrogate super-resolution(SR)framework that accelerates finite element method(FEM)-based computational fluid dynamics(CFD)using deep learning.High-resolution(HR)FEM-based CFDremains computationa...This study develops a surrogate super-resolution(SR)framework that accelerates finite element method(FEM)-based computational fluid dynamics(CFD)using deep learning.High-resolution(HR)FEM-based CFDremains computationally prohibitive for time-sensitive applications,including patient-specific aneurysm hemodynamics where rapid turnaround is valuable.The proposed pipeline learns to reconstruct HR velocity-magnitude fields fromlow-resolution(LR)FEM solutions generated under the same governing equations and boundary conditions.It consistsof three modules:(i)offline pre-training of a residual network on representative vascular geometries;(ii)lightweightfine-tuning to adapt the pretrained model to geometric variability,including patient-specific aneurysm morphologies;and(iii)an unstructured-to-structured sampling strategy with region-of-interest upsampling that concentrates resolution in flow-critical zones(e.g.,the aneurysm sac)rather than the full domain.This targeted reconstruction substantiallyreduces inference and post-processing cost while preserving key HR flow features.Experiments on cerebral aneurysmmodels show that HR velocity-magnitude fields can be recovered with accuracy comparable to direct HR simulationsat less than 1%of the direct HR simulation cost per analysis(LR simulation and SR inference),while adaptation to newgeometries requires only lightweight fine-tuning with limited target-specific HR data.While clinical endpoints andadditional variables(e.g.,pressure or wall-based metrics)are left for future work,the results indicate that the proposedsurrogate SR approach can streamline FEM-based CFD workflows toward near real-time hemodynamic analysis acrossmorphologically similar vascular models.展开更多
Oil shale is characterized by a dense structure,low proportion of pores and fissures,and low permeability.Pore-fracture systems serve as crucial channels for shale oil migration,directly influencing the production eff...Oil shale is characterized by a dense structure,low proportion of pores and fissures,and low permeability.Pore-fracture systems serve as crucial channels for shale oil migration,directly influencing the production efficiency of shale oil resources.Effectively stimulating oil shale reservoirs remains a challenging and active research topic.This investigation employed shale specimens obtained from the Longmaxi Formation.Scanning electron microscopy,fluid injection experiments,and fluid-structure interaction simulations were used to comprehensively analyze structural changes and fluid flow behavior under high temperatures from microscopic to macroscopic scales.Experimental results indicate that the temperature has little effect on the structure and permeability of shale before 300℃.However,there are two threshold temperatures within the range of 300 to 600℃that have significant effects on the structure and permeability of oil shale.The first threshold temperature is between 300 and 400℃,which causes the oil shale porosity,pore-fracture ratio,and permeability begin to increase.This is manifested by the decrease in micropores and mesopores,the increase in macropores,and the formation of a large number of isolated pores and fissures within the shale.The permeability increases but not significantly.The second threshold temperature is between 500 and 600℃,which increases the permeability of oil shale significantly.During this stage,micropores and mesopores are further reduced,and macropores are significantly enlarged.A large number of connected and penetrated pores and fissures are formed.More numerous and thicker streamlines appear inside the oil shale.The experimental results demonstrate that high temperatures significantly alter the microstructure and permeability of oil shale.At the same time,the experimental results can provide a reference for the research of in-situ heating techniques in oil shale reservoir transformation.展开更多
Ingestion of microplastics by various organisms has been widely evidenced.Chemicals associated with microplastics(MPs)may be released to digestive tracts upon ingestion.However,the effect of aging and temperature on t...Ingestion of microplastics by various organisms has been widely evidenced.Chemicals associated with microplastics(MPs)may be released to digestive tracts upon ingestion.However,the effect of aging and temperature on the chemical desorption for MPs remains poorly understood.The exposure of polyethylene(PE)particles to UV radiation in dry air,tap water,and sea water was conducted to mimic the aging process of MPs in different environments.Polychlorinated biphenyls(PCBs),as a typical hydrophobic organic contaminant,were preloaded in these aged and pristine PE.The desorption was performed by exposing preloaded PE particles in simulated gastric and gut fluids at 25℃and 40℃.After UV aging,the average diameter of PE particles decreased rapidly with aging time,indicating continuously fragmentation of PE under UV exposure.The desorption of PCBs from PE particles under different conditions varied from 7%to 40%,and that from aged PE in gut fluid at 37℃was significantly higher than those under other conditions(P<0.05).Furthermore,a clear declining trend was observed as lg K_(ow)(octanol-water partition coefficient)value increased.The aging process,hydrophobicity of chemicals,and incubation temperature were important factors on the desorption of PCBs from PE.The present study helps understand the desorption of PCBs from microplastics and the potential risks of microplastics ingestion by organisms.展开更多
Though magnesium(Mg)alloys are highly attractive for their use as biodegradable/temporary implants,they can be critically compromised in such applications due to their susceptibility to corrosion and stress corrosion ...Though magnesium(Mg)alloys are highly attractive for their use as biodegradable/temporary implants,they can be critically compromised in such applications due to their susceptibility to corrosion and stress corrosion cracking(SCC)in human body fluid(such as Hanks’solution).This study investigated the role of additions of bovine serum albumin(BSA)and glucose to Hanks’solution in SCC of a Mg alloy,ZK60.The study reproducibly demonstrated the novel and unique characteristic of the acutely elliptical shape of the overall fracture surface of alloy subjected to SCC tests,exclusively when BSA was added to the Hanks’solution,whereas tests in the Hanks’solution without BSA produced the fracture surface of usual circular shape.Also,the BSA addition to the Hanks’solution produced contrasting influences on SCC and electrochemical corrosion.The study provides a comprehensive mechanistic explanation for the two phenomena.展开更多
Zinc was recently suggested to be a potential candidate material for degradable coronary artery stent.The corrosion behavior of pure zinc exposed to r-SBF up to 336 h was investigated by electrochemical measurements a...Zinc was recently suggested to be a potential candidate material for degradable coronary artery stent.The corrosion behavior of pure zinc exposed to r-SBF up to 336 h was investigated by electrochemical measurements and immersion tests. The morphology and chemical composites of the corrosion products were investigated by scanning electron microscope, grazing-incidence X-ray diffraction, X-ray photoelectron spectroscopy and Fourier transform infrared spectrometer. The results demonstrate that the initial corrosion products on the pure zinc mainly consist of zinc oxide/hydroxide and zinc/calcium phosphate compounds. The pure Zn encounters uniform corrosion with an estimated corrosion rate of 0.02-0.07 mmy;during the immersion, which suggests the suitability of pure Zn for biomedical applications.展开更多
Hydroxyapatite coatings were directly prepared on anodized titanium by electro-deposition method in a modified simulated body fluid.The configuration,structure and bioactivity of the coating were investigated with sca...Hydroxyapatite coatings were directly prepared on anodized titanium by electro-deposition method in a modified simulated body fluid.The configuration,structure and bioactivity of the coating were investigated with scanning electron microscopy(SEM),X-ray diffraction analyzer(XRD)and Fourier transform infrared spectros-copy(FTIR)techniques.The results demonstrated that pure and homogeneous hydroxyapatite coating can be obtained without any post-treatment.The prepared coating showed good bioactivity in simulated body fluid(SBF).The time required for a fully covered dense hydroxyapatite coatings was 4 days immersion in SBF.展开更多
Magnesium alloys were considered to be used as biodegradable implants due to their biocompatibility,biodegradability and nontoxicity.However,under the simultaneous action of corrosive environment and mechanical loadin...Magnesium alloys were considered to be used as biodegradable implants due to their biocompatibility,biodegradability and nontoxicity.However,under the simultaneous action of corrosive environment and mechanical loading in human body,magnesium alloys are easy to be affected by corrosion fatigue and stress corrosion cracking.In this work,the fatigue behavior of the extruded Mg-Zn-Y-Nd alloy used for vascular stents was studied both in air and in simulated body fluid(SBF).It was revealed that the fatigue limit of as-extruded Mg-Zn-Y-Nd alloy in air is about 65 MPa at 10^7 cycles,while there is no limit in SBF and shows a linear relationship between the fatigue life and stress amplitudes.The fatigue crack source in air was formed by the inclusions and defects.However,the stress corrosion and hydrogen embrittlement are the main reasons for the formation of the fatigue initial crack source in SBF.展开更多
In this work, a two-dimensional fluid model has been employed to study the characteristics of Ar/O2 radio frequency（RF） inductively coupled plasma discharges. The emphasis of this work has been put on the influence ...In this work, a two-dimensional fluid model has been employed to study the characteristics of Ar/O2 radio frequency（RF） inductively coupled plasma discharges. The emphasis of this work has been put on the influence of the external parameters（i.e., the RF power, the pressure, and the Ar/O2 gas ratio） on the plasma properties. The numerical results show that the RF power has a significant influence on the amplitude of the plasma density rather than on the spatial distribution.However, the pressure and the Ar/O2 gas ratio affect not only the amplitude of the plasma density, but also the spatial uniformity. Finally, the comparison between the simulation results and the experimental data has been made at different gas pressures and oxygen contents, and a good agreement has been achieved.展开更多
Computational fluid dynamics（CFD） simulations are adopted to investigate rectangular microchannel flows with various periodic micro-structured wall by introducing velocity slip boundary condition at low Reynolds num...Computational fluid dynamics（CFD） simulations are adopted to investigate rectangular microchannel flows with various periodic micro-structured wall by introducing velocity slip boundary condition at low Reynolds number. The purpose of the current study is to numerically find out the effects of periodic micro-structured wall on the flow resistance in rectangular microchannel with the different spacings between microridges ranging from 15 to 60 pm. The simulative results indicate that pressure drop with different spacing between microridges increases linearly with flow velocity and decreases monotonically with slip velocity; Pressure drop reduction also increases with the spacing between microridges at the same condition of slip velocity and flow velocity. The results of numerical simulation are compared with theoretical predictions and experimental results in the literatures. It is found that there is qualitative agreement between them.展开更多
We investigated the effect of supply air rate and temperature on formaldehyde emission characteristics in an environment chamber.A three-dimensional computational fluid dynamics(CFD) chamber model for simulating forma...We investigated the effect of supply air rate and temperature on formaldehyde emission characteristics in an environment chamber.A three-dimensional computational fluid dynamics(CFD) chamber model for simulating formaldehyde emission in twelve different cases was developed for obtaining formaldehyde concentration by the area-weighted average method.Laboratory experiments were conducted in an environment chamber to validate the simulation results of twelve different cases and the formaldehyde concentration was measured by continuous sampling.The results show that there was good agreement between the model prediction and the experimental values within 4.3 difference for each case.The CFD simulation results varied in the range from 0.21 mg/m3 to 0.94 mg/m3,and the measuring results in the range from 0.17 mg/m3 to 0.87 mg/m3.The variation trend of formaldehyde concentration with supply air rate and temperature variation for CFD simulation and experiment measuring was consistent.With the existence of steady formaldehyde emission sources,formaldehyde concentration generally increased with the increase of temperature,and it decreased with the increase of air supply rate.We also provided some reasonable suggestions to reduce formaldehyde concentration and to improve indoor air quality for newly decorated rooms.展开更多
In this study,a KrF excimer laser was used to modify the biodegradable Mg-1Ca alloy and the time-evolution degradation behavior of the alloy before and after laser treatment was investigated in simulated body fluid(SB...In this study,a KrF excimer laser was used to modify the biodegradable Mg-1Ca alloy and the time-evolution degradation behavior of the alloy before and after laser treatment was investigated in simulated body fluid(SBF)solution using immersion tests and electrochemical impedance spectroscopy(EIS).A 5μm melted layer with a homogeneous microstructure and an MgO film on the surface were achieved by laser radiation.Corrosion observations(hydrogen evolution,morphology and corrosion products)and EIS results revealed an improvement of corrosion resistance after laser treatment for 48 h.It was found a two-layer structure developed after 2 h immersion on both the untreated and laser-treated alloys,but the sequence of forming the two layers was opposite and greatly influenced by the laser-treated layer.The time-evolution corrosion processes on the untreated and laser-treated alloys were discussed,providing a better understanding of corrosion behavior of biodegradable Mg alloys modified by excimer laser.展开更多
According to the recently developed single-trough floating machine with the world's largest volume(inflatable mechanical agitation flotation machine with volume of 320 m3) in China, the gas-fluid two-phase flow in...According to the recently developed single-trough floating machine with the world's largest volume(inflatable mechanical agitation flotation machine with volume of 320 m3) in China, the gas-fluid two-phase flow in flotation cell was simulated using computational fluid dynamics method. It is shown that hexahedral mesh scheme is more suitable for the complex structure of the flotation cell than tetrahedral mesh scheme, and a mesh quality ranging from 0.7 to 1.0 is obtained. Comparative studies of the standard k-ε, k-ω and realizable k-ε turbulence models were carried out. It is indicated that the standard k-ε turbulence model could give a result relatively close to the practice and the liquid phase flow field is well characterized. In addition, two obvious recirculation zones are formed in the mixing zones, and the pressure on the rotor and stator is well characterized. Furthermore, the simulation results using improved standard k-ε turbulence model show that surface tension coefficient of 0.072, drag model of Grace and coefficient of 4, and lift coefficient of 0.001 can be achieved. The research results suggest that gas-fluid two-phase flow in large flotation cell can be well simulated using computational fluid dynamics method.展开更多
The corrosion behaviors of SUS316L stainless steel, Co Cr alloy and Ti 6Al 4V alloy in Ringer’s, PBS(-) and Hank’s solutions have been investigated. The results indicate that the corrosion of Ringer’s solution is t...The corrosion behaviors of SUS316L stainless steel, Co Cr alloy and Ti 6Al 4V alloy in Ringer’s, PBS(-) and Hank’s solutions have been investigated. The results indicate that the corrosion of Ringer’s solution is the strongest, then followed by PBS(-) and Hank’s solution. The presence of HPO 2- 4, H 2PO - 4, SO 2- 4 and glucose in the PBS(-)and Hank’s solution probably reduces the corrosion inhibitor and corrosion current. The decrease of the solution’s pH significantly increases the corrosion rate and susceptibility to localized corrosion of SUS316L SS and Co Cr alloy. However, Ti 6Al 4V alloy exhibits an exceptional stability and has only a slight increase of corrosion rate with decreasing pH.展开更多
Fatigue behaviors of a biocompatible Ni-free Zr60.14Cu22.31Fe4.85Al9.7Ag3 Zr-based bulk metallic glass （BMG） have been studied under three-point-bending test in a simulated body fluid （SBF） at 37 ℃ and compared w...Fatigue behaviors of a biocompatible Ni-free Zr60.14Cu22.31Fe4.85Al9.7Ag3 Zr-based bulk metallic glass （BMG） have been studied under three-point-bending test in a simulated body fluid （SBF） at 37 ℃ and compared with those in air at room temperature （RT）. The BMG shows a high fatigue limit of approximately 366 MPa in SBF, which was slightly lower than that in air （400 MPa）. The fatigue cracks tended to initiate from the defects such as cast-pores, inclusions and corners of the samples and propagate in a similar path in SBF and in air. Three distinct regions, i.e. a crack-initiation region, a stable crack-growth region and an unstable fast-fracture region were clearly observed on the fatigue-fractured surface. Although pitting occurred at the defects where crack initiated, it does not affect significantly the fatigue life of the BMG, because the lifetime in the present BMG is mainly determined by crack propagation. The high corrosion-fatigue limit of the studied BMG results from its excellent corrosion resistance in SBF and intrinsically good toughness.展开更多
The effect of flow control devices（FCDs） on the uniformity of flow characteristics in a seven-strand symmetrical trapezoidal tundish was studied using both an experimental 1：2.5 hydraulic model and a numerical simu...The effect of flow control devices（FCDs） on the uniformity of flow characteristics in a seven-strand symmetrical trapezoidal tundish was studied using both an experimental 1：2.5 hydraulic model and a numerical simulation of a 1：1 geometric model.The variation coefficient（CV） was defined to evaluate the flow uniformity of the seven-strand tundish.An optimized FCD configuration was proposed on the basis of the evaluation of experimental results.It is concluded that a turbulence inhibitor（TI） and U-type dam are essential to improve the uniformity of fluid flow in the seven-strand tundish.In addition,the configuration of inclination T-type dams with a height of 200 mm between the second and third strands and with a height of 300 mm between the third and fourth strands can minimize the proportion of dead zone.After optimizing the configuration of FCDs,the variation coefficient reduces below 20%of the mean value,and the average proportion of dead zone is just 14.6%;in addition,the temperature fluctuation between the strands could be controlled within 0.6 K.In summary,the uniformity of flow and temperature in the seven-strand tundish is greatly improved.展开更多
Objective To compare the cupric ion releasing in vitro o.f the three IUDs. Methods The stability o.f cupric ion releasing o.f IUDs including TCu 380.4 IUD （TCu 380A）, Multiload Cu375 IUD （MCu 375） and Yuangong 365...Objective To compare the cupric ion releasing in vitro o.f the three IUDs. Methods The stability o.f cupric ion releasing o.f IUDs including TCu 380.4 IUD （TCu 380A）, Multiload Cu375 IUD （MCu 375） and Yuangong 365 copper-bearing indomethacin-releasing IUD （Yuangong 365） by the determination of cupric ion releasing in simulated uterine fluid. The simulated uterine fluid was used for releasing media. Copper ion was determined by flame atomic absorption spectrometer. Results The cupric ion releasing of three IUDs were instable at the beginning and tend to be stable gradually. In the stable phase, the average level of cupric ion releasing of TCu380A, MCu375 and Yuangong 365 were 4.25±2.71-7.62±6.42 μg, 4.92±1.23 -8.62±3.08 μg and 2.19±0.40-4.68±1.66 μg, respectively. TCu380A had higher instable releasing level than those of Yuangong 365 （P〈0. 05）. Conclusion TCu 380.4 and MCu 375 showed a ＂burst release＂ during the first few days and the.former was of great significance（P〈0.05）. The initial cupric ion releasing of Yuangong 365 appeared to be the lowest, followed by MCu375 and TCu380A in a releasing order展开更多
Porous and dense TiNi alloys were successfully fabricated by powder metallurgy(P/M) method, and to further improve their surface biocompatibility, surface modification techniques including grind using silicon-carbide(...Porous and dense TiNi alloys were successfully fabricated by powder metallurgy(P/M) method, and to further improve their surface biocompatibility, surface modification techniques including grind using silicon-carbide(SiC) paper, acid etching and alkali treatment were employed to produce either irregularly rough surface or micro-porous surface roughness. X-ray diffractometry(XRD), scanning electron microscopy(SEM) and energy dispersive X-ray spectroscopy(EDX) attached to SEM were used to characterize surface structure and the Ca-P coatings. Effects of the above surface treatments on the surface morphology, apatite forming ability were systematically investigated. Results indicate that all the above surface treatments increase the apatite forming ability of TiNi alloys in varying degrees when soaked in simulated body fluid(SBF). More apatite coatings formed on TiNi samples sintered at 1050℃ and 1100℃ due to their high porosity and pure TiNi phase that is beneficial to heterogeneous nucleation. Furthermore, more uniform apatite was fabricated on the sample sintered from the mixture of Ni and Ti powders.展开更多
Currently, when magnesium alloy sheet is rolled, the method of controlling roll temperature is simple and inaccurate. Furthermore, roll temperature has a large influence on the quality of magnesium alloy sheet; theref...Currently, when magnesium alloy sheet is rolled, the method of controlling roll temperature is simple and inaccurate. Furthermore, roll temperature has a large influence on the quality of magnesium alloy sheet; therefore, a new model using circular fluid flow control roll temperature has been designed. A fluid heat transfer structure was designed, the heat transfer process model of the fluid heating roll was simplified, and the finite di erence method was used to cal?culate the heat transfer process. Fluent software was used to simulate the fluid?solid coupling heat transfer, and both the trend and regularity of the temperature field in the heat transfer process were identified. The results show that the heating e ciency was much higher than traditional heating methods(when the fluid heat of the roll and tempera?ture distribution of the roll surface was more uniform). Moreover, there was a bigger temperature di erence between the input and the output, and after using reverse flow the temperature di erence decreased. The axial and circum?ferential temperature distributions along the sheet were uniform. Both theoretical calculation results and numerical simulation results of the heat transfer between fluid and roll were compared. The error was 1.8%–12.3%, showing that the theoretical model can both forecast and regulate the temperature of the roll(for magnesium alloy sheets) in the rolling process.展开更多
文摘This study develops a surrogate super-resolution(SR)framework that accelerates finite element method(FEM)-based computational fluid dynamics(CFD)using deep learning.High-resolution(HR)FEM-based CFDremains computationally prohibitive for time-sensitive applications,including patient-specific aneurysm hemodynamics where rapid turnaround is valuable.The proposed pipeline learns to reconstruct HR velocity-magnitude fields fromlow-resolution(LR)FEM solutions generated under the same governing equations and boundary conditions.It consistsof three modules:(i)offline pre-training of a residual network on representative vascular geometries;(ii)lightweightfine-tuning to adapt the pretrained model to geometric variability,including patient-specific aneurysm morphologies;and(iii)an unstructured-to-structured sampling strategy with region-of-interest upsampling that concentrates resolution in flow-critical zones(e.g.,the aneurysm sac)rather than the full domain.This targeted reconstruction substantiallyreduces inference and post-processing cost while preserving key HR flow features.Experiments on cerebral aneurysmmodels show that HR velocity-magnitude fields can be recovered with accuracy comparable to direct HR simulationsat less than 1%of the direct HR simulation cost per analysis(LR simulation and SR inference),while adaptation to newgeometries requires only lightweight fine-tuning with limited target-specific HR data.While clinical endpoints andadditional variables(e.g.,pressure or wall-based metrics)are left for future work,the results indicate that the proposedsurrogate SR approach can streamline FEM-based CFD workflows toward near real-time hemodynamic analysis acrossmorphologically similar vascular models.
基金supported by the Chongqing Natural Science Foundation of Chongqing,China(No.CSTB2022NSCQ-MSX0333)the Science and Technology Research Program of Chongqing Municipal Education Commission(Grant No.KJZD-K202401205)+1 种基金Chongqing Three Gorges University Graduate Research and Innovation Project Funding(No.YJSKY24045)Chongqing Engineering Research Center of Disaster Prevention&Control for Banks and Structures in Three Gorges Reservoir Area(No.SXAPGC24YB14,No.SXAPGC24YB03,No.SXAPGC24YB12)。
文摘Oil shale is characterized by a dense structure,low proportion of pores and fissures,and low permeability.Pore-fracture systems serve as crucial channels for shale oil migration,directly influencing the production efficiency of shale oil resources.Effectively stimulating oil shale reservoirs remains a challenging and active research topic.This investigation employed shale specimens obtained from the Longmaxi Formation.Scanning electron microscopy,fluid injection experiments,and fluid-structure interaction simulations were used to comprehensively analyze structural changes and fluid flow behavior under high temperatures from microscopic to macroscopic scales.Experimental results indicate that the temperature has little effect on the structure and permeability of shale before 300℃.However,there are two threshold temperatures within the range of 300 to 600℃that have significant effects on the structure and permeability of oil shale.The first threshold temperature is between 300 and 400℃,which causes the oil shale porosity,pore-fracture ratio,and permeability begin to increase.This is manifested by the decrease in micropores and mesopores,the increase in macropores,and the formation of a large number of isolated pores and fissures within the shale.The permeability increases but not significantly.The second threshold temperature is between 500 and 600℃,which increases the permeability of oil shale significantly.During this stage,micropores and mesopores are further reduced,and macropores are significantly enlarged.A large number of connected and penetrated pores and fissures are formed.More numerous and thicker streamlines appear inside the oil shale.The experimental results demonstrate that high temperatures significantly alter the microstructure and permeability of oil shale.At the same time,the experimental results can provide a reference for the research of in-situ heating techniques in oil shale reservoir transformation.
基金Supported by the National Natural Science Foundation of China(No.21936004)the Southern Marine Science and Engineering Guangdong Laboratory(Zhuhai)(No.SML2021SP208)the Fundamental Research Funds for the Central Universities(No.21623118)。
文摘Ingestion of microplastics by various organisms has been widely evidenced.Chemicals associated with microplastics(MPs)may be released to digestive tracts upon ingestion.However,the effect of aging and temperature on the chemical desorption for MPs remains poorly understood.The exposure of polyethylene(PE)particles to UV radiation in dry air,tap water,and sea water was conducted to mimic the aging process of MPs in different environments.Polychlorinated biphenyls(PCBs),as a typical hydrophobic organic contaminant,were preloaded in these aged and pristine PE.The desorption was performed by exposing preloaded PE particles in simulated gastric and gut fluids at 25℃and 40℃.After UV aging,the average diameter of PE particles decreased rapidly with aging time,indicating continuously fragmentation of PE under UV exposure.The desorption of PCBs from PE particles under different conditions varied from 7%to 40%,and that from aged PE in gut fluid at 37℃was significantly higher than those under other conditions(P<0.05).Furthermore,a clear declining trend was observed as lg K_(ow)(octanol-water partition coefficient)value increased.The aging process,hydrophobicity of chemicals,and incubation temperature were important factors on the desorption of PCBs from PE.The present study helps understand the desorption of PCBs from microplastics and the potential risks of microplastics ingestion by organisms.
基金funded by Monash University,AustraliaDepartment of Biotechnology,India through IITB-Monash Research Academy.
文摘Though magnesium(Mg)alloys are highly attractive for their use as biodegradable/temporary implants,they can be critically compromised in such applications due to their susceptibility to corrosion and stress corrosion cracking(SCC)in human body fluid(such as Hanks’solution).This study investigated the role of additions of bovine serum albumin(BSA)and glucose to Hanks’solution in SCC of a Mg alloy,ZK60.The study reproducibly demonstrated the novel and unique characteristic of the acutely elliptical shape of the overall fracture surface of alloy subjected to SCC tests,exclusively when BSA was added to the Hanks’solution,whereas tests in the Hanks’solution without BSA produced the fracture surface of usual circular shape.Also,the BSA addition to the Hanks’solution produced contrasting influences on SCC and electrochemical corrosion.The study provides a comprehensive mechanistic explanation for the two phenomena.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.51503014 and No.51501008)the State Key Laboratory for Advanced Metals and Materials(No.2016Z-03)
文摘Zinc was recently suggested to be a potential candidate material for degradable coronary artery stent.The corrosion behavior of pure zinc exposed to r-SBF up to 336 h was investigated by electrochemical measurements and immersion tests. The morphology and chemical composites of the corrosion products were investigated by scanning electron microscope, grazing-incidence X-ray diffraction, X-ray photoelectron spectroscopy and Fourier transform infrared spectrometer. The results demonstrate that the initial corrosion products on the pure zinc mainly consist of zinc oxide/hydroxide and zinc/calcium phosphate compounds. The pure Zn encounters uniform corrosion with an estimated corrosion rate of 0.02-0.07 mmy;during the immersion, which suggests the suitability of pure Zn for biomedical applications.
基金Supported by the Young Scholars Fund of Beijing University of Chemical Technology(QN0713)
文摘Hydroxyapatite coatings were directly prepared on anodized titanium by electro-deposition method in a modified simulated body fluid.The configuration,structure and bioactivity of the coating were investigated with scanning electron microscopy(SEM),X-ray diffraction analyzer(XRD)and Fourier transform infrared spectros-copy(FTIR)techniques.The results demonstrated that pure and homogeneous hydroxyapatite coating can be obtained without any post-treatment.The prepared coating showed good bioactivity in simulated body fluid(SBF).The time required for a fully covered dense hydroxyapatite coatings was 4 days immersion in SBF.
基金The authors are grateful for the financial support of Key Projects of the Joint Fund of the National Natural Science Foundation of China(No.U1804251)the National Key Research and Development Program of China(No.2018YFC1106703,2017YFB0702504 and 2016YFC1102403).
文摘Magnesium alloys were considered to be used as biodegradable implants due to their biocompatibility,biodegradability and nontoxicity.However,under the simultaneous action of corrosive environment and mechanical loading in human body,magnesium alloys are easy to be affected by corrosion fatigue and stress corrosion cracking.In this work,the fatigue behavior of the extruded Mg-Zn-Y-Nd alloy used for vascular stents was studied both in air and in simulated body fluid(SBF).It was revealed that the fatigue limit of as-extruded Mg-Zn-Y-Nd alloy in air is about 65 MPa at 10^7 cycles,while there is no limit in SBF and shows a linear relationship between the fatigue life and stress amplitudes.The fatigue crack source in air was formed by the inclusions and defects.However,the stress corrosion and hydrogen embrittlement are the main reasons for the formation of the fatigue initial crack source in SBF.
基金Project supported by the National Science and Technology Major Project of the Ministry of Science and Technology of China(Grant No.2011ZX02403-001)the National Natural Science Foundation of China(Grant No.11205025)
文摘In this work, a two-dimensional fluid model has been employed to study the characteristics of Ar/O2 radio frequency（RF） inductively coupled plasma discharges. The emphasis of this work has been put on the influence of the external parameters（i.e., the RF power, the pressure, and the Ar/O2 gas ratio） on the plasma properties. The numerical results show that the RF power has a significant influence on the amplitude of the plasma density rather than on the spatial distribution.However, the pressure and the Ar/O2 gas ratio affect not only the amplitude of the plasma density, but also the spatial uniformity. Finally, the comparison between the simulation results and the experimental data has been made at different gas pressures and oxygen contents, and a good agreement has been achieved.
基金National Natural Science Foundation of China (No.50435030)
文摘Computational fluid dynamics（CFD） simulations are adopted to investigate rectangular microchannel flows with various periodic micro-structured wall by introducing velocity slip boundary condition at low Reynolds number. The purpose of the current study is to numerically find out the effects of periodic micro-structured wall on the flow resistance in rectangular microchannel with the different spacings between microridges ranging from 15 to 60 pm. The simulative results indicate that pressure drop with different spacing between microridges increases linearly with flow velocity and decreases monotonically with slip velocity; Pressure drop reduction also increases with the spacing between microridges at the same condition of slip velocity and flow velocity. The results of numerical simulation are compared with theoretical predictions and experimental results in the literatures. It is found that there is qualitative agreement between them.
基金Funded by National Science Foundation(No.50778415 and No.50878177)
文摘We investigated the effect of supply air rate and temperature on formaldehyde emission characteristics in an environment chamber.A three-dimensional computational fluid dynamics(CFD) chamber model for simulating formaldehyde emission in twelve different cases was developed for obtaining formaldehyde concentration by the area-weighted average method.Laboratory experiments were conducted in an environment chamber to validate the simulation results of twelve different cases and the formaldehyde concentration was measured by continuous sampling.The results show that there was good agreement between the model prediction and the experimental values within 4.3 difference for each case.The CFD simulation results varied in the range from 0.21 mg/m3 to 0.94 mg/m3,and the measuring results in the range from 0.17 mg/m3 to 0.87 mg/m3.The variation trend of formaldehyde concentration with supply air rate and temperature variation for CFD simulation and experiment measuring was consistent.With the existence of steady formaldehyde emission sources,formaldehyde concentration generally increased with the increase of temperature,and it decreased with the increase of air supply rate.We also provided some reasonable suggestions to reduce formaldehyde concentration and to improve indoor air quality for newly decorated rooms.
文摘In this study,a KrF excimer laser was used to modify the biodegradable Mg-1Ca alloy and the time-evolution degradation behavior of the alloy before and after laser treatment was investigated in simulated body fluid(SBF)solution using immersion tests and electrochemical impedance spectroscopy(EIS).A 5μm melted layer with a homogeneous microstructure and an MgO film on the surface were achieved by laser radiation.Corrosion observations(hydrogen evolution,morphology and corrosion products)and EIS results revealed an improvement of corrosion resistance after laser treatment for 48 h.It was found a two-layer structure developed after 2 h immersion on both the untreated and laser-treated alloys,but the sequence of forming the two layers was opposite and greatly influenced by the laser-treated layer.The time-evolution corrosion processes on the untreated and laser-treated alloys were discussed,providing a better understanding of corrosion behavior of biodegradable Mg alloys modified by excimer laser.
基金Project(51074027)supported by the National Natural Science Foundation of China
文摘According to the recently developed single-trough floating machine with the world's largest volume(inflatable mechanical agitation flotation machine with volume of 320 m3) in China, the gas-fluid two-phase flow in flotation cell was simulated using computational fluid dynamics method. It is shown that hexahedral mesh scheme is more suitable for the complex structure of the flotation cell than tetrahedral mesh scheme, and a mesh quality ranging from 0.7 to 1.0 is obtained. Comparative studies of the standard k-ε, k-ω and realizable k-ε turbulence models were carried out. It is indicated that the standard k-ε turbulence model could give a result relatively close to the practice and the liquid phase flow field is well characterized. In addition, two obvious recirculation zones are formed in the mixing zones, and the pressure on the rotor and stator is well characterized. Furthermore, the simulation results using improved standard k-ε turbulence model show that surface tension coefficient of 0.072, drag model of Grace and coefficient of 4, and lift coefficient of 0.001 can be achieved. The research results suggest that gas-fluid two-phase flow in large flotation cell can be well simulated using computational fluid dynamics method.
文摘The corrosion behaviors of SUS316L stainless steel, Co Cr alloy and Ti 6Al 4V alloy in Ringer’s, PBS(-) and Hank’s solutions have been investigated. The results indicate that the corrosion of Ringer’s solution is the strongest, then followed by PBS(-) and Hank’s solution. The presence of HPO 2- 4, H 2PO - 4, SO 2- 4 and glucose in the PBS(-)and Hank’s solution probably reduces the corrosion inhibitor and corrosion current. The decrease of the solution’s pH significantly increases the corrosion rate and susceptibility to localized corrosion of SUS316L SS and Co Cr alloy. However, Ti 6Al 4V alloy exhibits an exceptional stability and has only a slight increase of corrosion rate with decreasing pH.
基金financially supported by the National Nature Science Foundation of China (Grant Nos. 51071072 and 51271081)
文摘Fatigue behaviors of a biocompatible Ni-free Zr60.14Cu22.31Fe4.85Al9.7Ag3 Zr-based bulk metallic glass （BMG） have been studied under three-point-bending test in a simulated body fluid （SBF） at 37 ℃ and compared with those in air at room temperature （RT）. The BMG shows a high fatigue limit of approximately 366 MPa in SBF, which was slightly lower than that in air （400 MPa）. The fatigue cracks tended to initiate from the defects such as cast-pores, inclusions and corners of the samples and propagate in a similar path in SBF and in air. Three distinct regions, i.e. a crack-initiation region, a stable crack-growth region and an unstable fast-fracture region were clearly observed on the fatigue-fractured surface. Although pitting occurred at the defects where crack initiated, it does not affect significantly the fatigue life of the BMG, because the lifetime in the present BMG is mainly determined by crack propagation. The high corrosion-fatigue limit of the studied BMG results from its excellent corrosion resistance in SBF and intrinsically good toughness.
基金supported by the National Natural Science Foundation of China (No.51404018)the Fundamental Research Funds for the Central Universities of China (No.FRF-TP-15-008A3)
文摘The effect of flow control devices（FCDs） on the uniformity of flow characteristics in a seven-strand symmetrical trapezoidal tundish was studied using both an experimental 1：2.5 hydraulic model and a numerical simulation of a 1：1 geometric model.The variation coefficient（CV） was defined to evaluate the flow uniformity of the seven-strand tundish.An optimized FCD configuration was proposed on the basis of the evaluation of experimental results.It is concluded that a turbulence inhibitor（TI） and U-type dam are essential to improve the uniformity of fluid flow in the seven-strand tundish.In addition,the configuration of inclination T-type dams with a height of 200 mm between the second and third strands and with a height of 300 mm between the third and fourth strands can minimize the proportion of dead zone.After optimizing the configuration of FCDs,the variation coefficient reduces below 20%of the mean value,and the average proportion of dead zone is just 14.6%;in addition,the temperature fluctuation between the strands could be controlled within 0.6 K.In summary,the uniformity of flow and temperature in the seven-strand tundish is greatly improved.
基金This study was supported by National Key Scientific and Technological Project(2004BA720A32)
文摘Objective To compare the cupric ion releasing in vitro o.f the three IUDs. Methods The stability o.f cupric ion releasing o.f IUDs including TCu 380.4 IUD （TCu 380A）, Multiload Cu375 IUD （MCu 375） and Yuangong 365 copper-bearing indomethacin-releasing IUD （Yuangong 365） by the determination of cupric ion releasing in simulated uterine fluid. The simulated uterine fluid was used for releasing media. Copper ion was determined by flame atomic absorption spectrometer. Results The cupric ion releasing of three IUDs were instable at the beginning and tend to be stable gradually. In the stable phase, the average level of cupric ion releasing of TCu380A, MCu375 and Yuangong 365 were 4.25±2.71-7.62±6.42 μg, 4.92±1.23 -8.62±3.08 μg and 2.19±0.40-4.68±1.66 μg, respectively. TCu380A had higher instable releasing level than those of Yuangong 365 （P〈0. 05）. Conclusion TCu 380.4 and MCu 375 showed a ＂burst release＂ during the first few days and the.former was of great significance（P〈0.05）. The initial cupric ion releasing of Yuangong 365 appeared to be the lowest, followed by MCu375 and TCu380A in a releasing order
基金Project(51274247) supported by the National Natural Science Foundation of ChinaProject(2014zzts177) support by the Fundamental Research Funds for the Central Universities,China
文摘Porous and dense TiNi alloys were successfully fabricated by powder metallurgy(P/M) method, and to further improve their surface biocompatibility, surface modification techniques including grind using silicon-carbide(SiC) paper, acid etching and alkali treatment were employed to produce either irregularly rough surface or micro-porous surface roughness. X-ray diffractometry(XRD), scanning electron microscopy(SEM) and energy dispersive X-ray spectroscopy(EDX) attached to SEM were used to characterize surface structure and the Ca-P coatings. Effects of the above surface treatments on the surface morphology, apatite forming ability were systematically investigated. Results indicate that all the above surface treatments increase the apatite forming ability of TiNi alloys in varying degrees when soaked in simulated body fluid(SBF). More apatite coatings formed on TiNi samples sintered at 1050℃ and 1100℃ due to their high porosity and pure TiNi phase that is beneficial to heterogeneous nucleation. Furthermore, more uniform apatite was fabricated on the sample sintered from the mixture of Ni and Ti powders.
基金National Natural Science Foundation of China(Grant No.U1510131)Key Research and Development Projects of Shanxi Province of China(Grant Nos.201603D121010,201603D111004)+3 种基金Science and Technology Project of Jin Cheng City of China(Grant No.20155010)Youth Program of National Natural Science Fund of China(Grant No.51604181)Project of Young Scholar of Shanxi ProvinceLeading Talent Project of Innovative Entrepreneurial Team of Jiangsu Province(Grant No.51501122)
文摘Currently, when magnesium alloy sheet is rolled, the method of controlling roll temperature is simple and inaccurate. Furthermore, roll temperature has a large influence on the quality of magnesium alloy sheet; therefore, a new model using circular fluid flow control roll temperature has been designed. A fluid heat transfer structure was designed, the heat transfer process model of the fluid heating roll was simplified, and the finite di erence method was used to cal?culate the heat transfer process. Fluent software was used to simulate the fluid?solid coupling heat transfer, and both the trend and regularity of the temperature field in the heat transfer process were identified. The results show that the heating e ciency was much higher than traditional heating methods(when the fluid heat of the roll and tempera?ture distribution of the roll surface was more uniform). Moreover, there was a bigger temperature di erence between the input and the output, and after using reverse flow the temperature di erence decreased. The axial and circum?ferential temperature distributions along the sheet were uniform. Both theoretical calculation results and numerical simulation results of the heat transfer between fluid and roll were compared. The error was 1.8%–12.3%, showing that the theoretical model can both forecast and regulate the temperature of the roll(for magnesium alloy sheets) in the rolling process.
