A piece of multimode optical fiber with a low num er ical aperture (NA) is used as an inexpensive microlens to collimate the output r adiation of a laser diode bar in the high numerical aperture (NA) direction.The em...A piece of multimode optical fiber with a low num er ical aperture (NA) is used as an inexpensive microlens to collimate the output r adiation of a laser diode bar in the high numerical aperture (NA) direction.The emissions of the laser diode bar are coupled into multimode fiber array.The radi ation from individual ones of emitter regions is optically coupled into individu al ones of fiber array.Total coupling efficiency and fiber output power are 75% and 15W,respectively.展开更多
The output radiation from the 100μm×1μm aperture of a high power Laser Diode (LD) is efficiently coupled into a 50μm multimode optical fiber.The fiber output of the high power LD with high brightness and high ...The output radiation from the 100μm×1μm aperture of a high power Laser Diode (LD) is efficiently coupled into a 50μm multimode optical fiber.The fiber output of the high power LD with high brightness and high power density is achieved.The power density is up to 3 6×104W/cm2 and the coupling efficiency is 70%.The extreme divergence and the astigmatism of high power LDs require the optics with complex lens structures and high performance.A double-curved lens with two crossed cylindrical lenses structured on both sides of the glass substrate is used in the coupling system.展开更多
Coupling plane wave into a single-mode fiber （SMF） with high and steady coupling efficiency is crucial for fiber- based free-space laser systems, where random angular jitters are the main influencing factors of fibe...Coupling plane wave into a single-mode fiber （SMF） with high and steady coupling efficiency is crucial for fiber- based free-space laser systems, where random angular jitters are the main influencing factors of fiber coupling. In this paper, we verified a new adaptive-optic device named adaptive fiber coupler （AFC） which could compensate angular jitters and improve the SMF coupling efficiency in some degree. Experiments of SMF coupling under the angular jitter situation using AFC have been achieved. Stochastic parallel gradient descent （SPGD） algorithm is employed as the control strategy, of which the iteration rate is 625 Hz. In closed loop, the coupling efficiency keeps above 65% when angular errors are below 80/3tad. The compensation bandwidth is 35 Hz at sine-jitter of 15 ~rad amplitude with average coupling efficiency of above 60%. Also, experiments with simulated turbulence have been studied. The average coupling efficiency increases from 31.97% in open loop to 61.33% in closed loop, and mean square error （MSE） of coupling efficiency drops from 7.43% to 1.75%.展开更多
The theoretical investigation of the coupling efficiency of a laser diode to a single mode fiber via a hemispherical lens on the tip of the tapered fiber in the presence of possible transverse offset and angular misma...The theoretical investigation of the coupling efficiency of a laser diode to a single mode fiber via a hemispherical lens on the tip of the tapered fiber in the presence of possible transverse offset and angular mismatch is reported.Without the misalignment,coupling efficiency increases with the decreasing of taper length.With the misalignment,this relation is that the coupling efficiency decreases with each kind of offset.展开更多
Upconversion nanoparticles(UCNPs)have attracted considerable interest due to their large anti-Stokes shift,offering promising applications in lasing.Here,multi-wavelength upconversion whispering gallery mode(WGM)lasin...Upconversion nanoparticles(UCNPs)have attracted considerable interest due to their large anti-Stokes shift,offering promising applications in lasing.Here,multi-wavelength upconversion whispering gallery mode(WGM)lasing is demonstrated in silica microspheres coated with NaYF_(4)@NaYbF_(4):1%Tm^(3+)@NaYF_(4)nanoparticles and coupled with tapered fibers.Under continuous-wave 980 nm pumping,low-threshold lasing is achieved across Tm3+transitions from near-infrared to visible,with an ultra-low threshold of 0.61μWfor the 3H_(4)→3H_(6)transition.Additionally,upconversion laser output can also be achieved in Er^(3+)-and Ho^(3+)-activated microspheres.These results establish tapered fiber coupling as a versatile approach for enhancing upconversion microlasers.展开更多
According to the principle of choosing the light source in the fiber optic sensing measurement,semiconductor laser is used as the light source of fiber optic sensor and single-mode fiber is used as the tail fiber of l...According to the principle of choosing the light source in the fiber optic sensing measurement,semiconductor laser is used as the light source of fiber optic sensor and single-mode fiber is used as the tail fiber of light source. Based on optical design software Zemax’s pure non-sequential components,a coupling system of semiconductor laser and single-mode fiber is designed. By analyzing the beam characteristics of the semiconductor laser and the coupled mode theory of semiconductor laser and single-mode fiber,the combined lens consists of a ball lens and a collimating lens for the purpose of improving the coupling efficiency and adjusting tolerance. The simulation results show that the coupling efficiency can reach about 78% by using one million ray traces on non-sequential components,while the experimental test result is 69.11%,accordingly,the reasons for the difference between the experiment and the simulation results are analyzed.展开更多
Based on optofluidics and whispering gallery mode(WGM)theory,here an optofluidic refractive index sensor with microtube-coupled suspended core fiber(SCF)is proposed.It solves the issues of general sensors with microca...Based on optofluidics and whispering gallery mode(WGM)theory,here an optofluidic refractive index sensor with microtube-coupled suspended core fiber(SCF)is proposed.It solves the issues of general sensors with microcavity-coupled fiber taper such as too fragile,unstable performance due to open coupling,poor portability and repeatability,while overcoming the poor performance of low refractive index sensing in general full-package fiber sensors.The sensor only needs a very small amount of liquid sample(about 1.8 nL).The proposed sensor combines the excellent performance of full package,optofluidics and WGM resonator.The resonant characteristics and sensing performance of the sensor are analyzed and discussed by the theoretical simulation.The simulation results indicate that the sensor has a wide refractive index sensing range(1.330-1.700)and good performance.The resonance wavelength shift has a good linear relationship with the liquid refractive index variation.In the low refractive index region,the sensitivity is 222.5-247.5 nm/RIU,Q-factor is 1.03×10^(3) and the detection limit is 3.64×10^(-4) RIU.In the medium and high refractive index regions,the sensitivity is 564.4-846.2 nm/RIU,Q-factor is up to 8.62×10^(4),and the detection limit can be as low as 1.29×10^(-6) RIU.The sensor exhibits a high sensitivity,a high Q-factor and a very low detection limit.展开更多
We consider a fiber coupled cavity array. Each cavity is doped with a single two-level atom. By treating the atom-cavity systems as combined polaritonie qubits, we can transform it into a polaritonic qubit-qubit array...We consider a fiber coupled cavity array. Each cavity is doped with a single two-level atom. By treating the atom-cavity systems as combined polaritonie qubits, we can transform it into a polaritonic qubit-qubit array in the dispersive regime. We show that the four fiber coupled cavity open chain and ring can both generate the four qubit W state and cluster state, and can both transfer one and two qubit arbitrary states. We also discuss the dynamical behaviors of the four fiber coupled cavity array with unequal couplings.展开更多
Experimental design and response surface methodology（RSM） were used to optimize the modification of conditions for glass surface grafting with acrylamide（AM） monomer for preparation of a glass fiber reinforced pol...Experimental design and response surface methodology（RSM） were used to optimize the modification of conditions for glass surface grafting with acrylamide（AM） monomer for preparation of a glass fiber reinforced poly（vinylidene fluoride）（PVDF） composite membrane（GFRP-CM）. The factors considered for experimental design were the UV（ultraviolet）-irradiation time, the concentrations of the initiator and solvent, and the kinds and concentrations of the silane coupling agent. The optimum operating conditions determined were UV-irradiation time of 25 min, an initiator concentration of 0–0.25 wt.%,solvent of N-Dimethylacetamide（DMAC）, and silane coupling agent KH570 with a concentration of 7 wt.%. The obtained optimal parameters were located in the valid region and the experimental confirmation tests conducted showed good accordance between predicted and experimental values. Under these optimal conditions, the water absorption of the grafted modified glass fiber was improved from 13.6% to 23%; the tensile strength was enhanced and the peeling strength of the glass fiber reinforced PVDF composite membrane was improved by 23.7% and 32.6% with an AM concentration at 1 wt.% and 2 wt.%. The surface composition and microstructure of AM grafted glass fiber were studied via several techniques including Field Emission Scanning Electron Microscopy（FESEM）, Fourier transform infrared spectroscopy-attenuated total reflectance（FTIR-ATR） and energy dispersive X-ray spectroscopy（EDX）. The analysis of the EDX and FTIR-ATR results confirmed that the AM was grafted to the glass fiber successfully by detecting and proving the existence of nitrogen atoms in the GFRP-CM.展开更多
Integrated diffractive optical mode converter, consisting of a diffractive optical element (DOE) and a slab waveguide, is used for fiber-to-waveguide coupling. The phase of the DOE is generally designed by optimizatio...Integrated diffractive optical mode converter, consisting of a diffractive optical element (DOE) and a slab waveguide, is used for fiber-to-waveguide coupling. The phase of the DOE is generally designed by optimization algorithm. In this paper, the precise design, a new method with one more restrictive way, is adopted to design the diffractive optical mode converter for fiber-to-waveguide coupling. Through this method, the intensity of any point on the output plane is fully filled with the required demand. Compared with what previously published, the coupling loss of the precise designed converter is lower.展开更多
In the paper,an optical fiber sensor based on a seven-core fiber composite structure is presented,which enables dual-parameter sensing of bending and temperature.The proposed structure is fabricated by combining the s...In the paper,an optical fiber sensor based on a seven-core fiber composite structure is presented,which enables dual-parameter sensing of bending and temperature.The proposed structure is fabricated by combining the strongly-coupled seven-core fibers(SC-SCFs)and a weakly-coupled seven-core fiber(WC-SCF).The SC-SCF acts as a beam coupler and enhances the Mach-Zehnder interference,while the WC-SCF serves as the enhanced section of another Mach-Zehnder interference.Therefore,the spectrum response of the fiber structure mentioned above exhibits a superposition effect of two Mach-Zehnder interferometers(MZIs).Among them,two dips corresponding to different MZIs are used to measure bending and temperature.The experimental results show the bending sensitivity and temperature sensitivity of the two MZIs are-4.238 nm/m^(-1),-2.263 nm/m^(-1),0.047 nm/℃,and 0.064 nm/,respectively.It proves℃that our sensor is very sensitive to bending.Through the dual-wavelength matrix method,the bending and temperature can be measured simultaneously.With the benefit of the composite structure,low cost,and ease of fabrication,the proposed sensor can be used in harsh environments.展开更多
The side-coupler of angle polished method, using angle-polished multimode fiber and optical adhesive, is used to efficiently pump an Yb-doped double-clad fiber laser. The maximum coupling efficiency of 78.6% is achiev...The side-coupler of angle polished method, using angle-polished multimode fiber and optical adhesive, is used to efficiently pump an Yb-doped double-clad fiber laser. The maximum coupling efficiency of 78.6% is achieved by the side-coupler for a multimode fiber with a circular core of 200μm and a double-clad fiber with a 350/400μm D-shaped inner cladding. While laser diodes (LDs) with three side-couplers are simultaneously used as pump sources, maximum output power of 1.38 W and slope efficiency of 48.9% are demonstrated in the fiber laser system.展开更多
Using a fiber Bragg grating (FBG) and a Fabry-Perot cavity composed of two fiber Bragg gratings (FBGFP) as its frequency-selective components, a type of single frequency all-fiber ring laser permits oscillation only o...Using a fiber Bragg grating (FBG) and a Fabry-Perot cavity composed of two fiber Bragg gratings (FBGFP) as its frequency-selective components, a type of single frequency all-fiber ring laser permits oscillation only on one longitudinal mode of the main cavity without modehopping while the cavity length can be up to tens of meters. The salient feature is due to the single narrowband resonance of the FBGFP filter. Such a fiber ring laser is achieved experimentally, and the laser mode is limited inside the single resonance of the FBGFP.展开更多
A Galerkin's method-based numerical procedure is extended to obtain the modal field distribution of multicore photonic crystal fibers for the first time to our knowledge, which can reveal how the air hole size inf...A Galerkin's method-based numerical procedure is extended to obtain the modal field distribution of multicore photonic crystal fibers for the first time to our knowledge, which can reveal how the air hole size influences the mode coupling and how the coupling strength varies with wavelength. These results will be helpful in the future design of multicore photonic crystal fibers with proper guidance properties.展开更多
At liquid-nitrogen temperature, at 10-kHz pulse repetition rate, Q-switched 36-ns pulses with average output power of 4 W at 2.05 μm and 4.5-W continuous wave output power with a total optical-optical conversion effi...At liquid-nitrogen temperature, at 10-kHz pulse repetition rate, Q-switched 36-ns pulses with average output power of 4 W at 2.05 μm and 4.5-W continuous wave output power with a total optical-optical conversion efficiency of 30%, were achieved from a 6% Tm, 0.5% Ho:YLiF4 laser. This laser was end-pumped by a fiber-coupled laser diode emitting up to 15 W around 792 nm. The 1-m-long optical fiber carrying the pump radiation has a core diameter of 700 μm with a numerical aperture of 0.22.展开更多
Based on the high-speed development of the fiber laser in recent years, the development of researching 915 nm semiconductor laser as main pumping sources of the fiber laser is at a high speed. Because the beam quality...Based on the high-speed development of the fiber laser in recent years, the development of researching 915 nm semiconductor laser as main pumping sources of the fiber laser is at a high speed. Because the beam quality of the laser diode is very poor, the 915 nm laser diode is generally based on optical fiber coupling module to output the laser. Using the beam-shaping and fiber-coupling technology to improve the quality of output beam light, we present a kind of high-power and high-brightness semiconductor laser module, which can output 13.22 W through the optical fiber. Based on 915 nm GaAs semiconductor laser diode which has output power of 13.91 W, we describe a thoroughly detailed procedure for reshaping the beam output from the semiconductor laser diode and coupling the beam into the optical fiber of which the core diameter is 105 μm and the numerical aperture is 0.18. We get 13.22 W from the output fiber of the module at 14.5 A, the coupling efficiency of the whole module is 95.03% and the brightness is 1.5 MW/cm2-str. The output power of the single chip semiconductor laser module achieves the advanced level in the domestic use.展开更多
The coupling between guided optical waves in magneto-optic fiber Bragg gratings （MFBGs） with linear birefringence is investigated using the eigen-mode and coupled-mode approaches. The relationship between the polari...The coupling between guided optical waves in magneto-optic fiber Bragg gratings （MFBGs） with linear birefringence is investigated using the eigen-mode and coupled-mode approaches. The relationship between the polarization-dependent loss （PDL） and the eigen states of polarization （SOPs） in the MFBGs is discussed. Only the MFBCs with low linear birefringence are applied to the peak PDL-based magnetic field measurement, after which the linear dynamic range is determined using the relative magnitude of linear and magnetically induced circular birefringence. In this letter, a theoretical model is presented to explain the experimental results and help develop novel MFBG-based devices.展开更多
We report a high-power ultra-narrow fiber-coupled diode laser using a Faraday anomalous dispersion optical filter(FADOF) as an external cavity element.An external cavity suitable for both the fiber-coupled package and...We report a high-power ultra-narrow fiber-coupled diode laser using a Faraday anomalous dispersion optical filter(FADOF) as an external cavity element.An external cavity suitable for both the fiber-coupled package and FADOF configuration has been proposed.Using a87Rb-based FADOF as the frequency-selective element,we realized a 103 W continuous laser output with a uniform circular beam.The center wavelength was precisely locked at the D2line of the Rb resonance,and the bandwidth was narrowed from 1.8 nm (free-running,full width at half maximum (FWHM)) to0.013 nm (6.9 GHz,FWHM).The side mode suppression ratio reached 31 dB.Such diode lasers with precise wavelength and high spectral brightness have critical applications in many fields,such as high-energy gas laser pumping,spinexchange optical pumping,Raman spectroscopy and nonlinear optics.展开更多
A polarization-maintained coupled optoelectronic oscillator（COEO） with its performance significantly improved by a short-length unpumped erbium-doped fiber（EDF） is reported and experimentally investigated.A 10 GHz...A polarization-maintained coupled optoelectronic oscillator（COEO） with its performance significantly improved by a short-length unpumped erbium-doped fiber（EDF） is reported and experimentally investigated.A 10 GHz optical pulse train with a supermode suppression ratio of 61.8 d B and a 10 GHz radio frequency signal with a sidemode suppression ratio of 94 d B and a phase noise of-121.9 d Bc∕Hz at 10 k Hz offset are simultaneously generated. Thanks to saturable absorption of the 1 m unpumped EDF, which introduces relatively large cavity loss to the undesired modes and noise, the supermode suppression ratio and the phase noise are improved by 9.4 and 7.9 d B, respectively.展开更多
Tapered fibers with diameters ranging from 1 to 4 μm are widely used to excite the whispering-gallery(WG)modes of microcavities. Typically, the transmission spectrum of a WG cavity coupled to a waveguide around a res...Tapered fibers with diameters ranging from 1 to 4 μm are widely used to excite the whispering-gallery(WG)modes of microcavities. Typically, the transmission spectrum of a WG cavity coupled to a waveguide around a resonance assumes a Lorentzian dip morphology due to resonant absorption of the light within the cavity. In this paper, we demonstrate that the transmission spectra of a WG cavity coupled with an ultrathin fiber(500–700 nm)may exhibit both Lorentzian dips and peaks, depending on the gap between the fiber and the microcavity. By considering the large scattering loss of off-resonant light from the fiber within the coupling region, this phenomenon can be attributed to partially resonant light bypassing the lossy scattering region via WG modes, allowing it to be coupled both to and from the cavity, then manifesting as Lorentzian peaks within the transmission spectra.This implies the system could be implemented within a bandpass filter framework.展开更多
文摘A piece of multimode optical fiber with a low num er ical aperture (NA) is used as an inexpensive microlens to collimate the output r adiation of a laser diode bar in the high numerical aperture (NA) direction.The emissions of the laser diode bar are coupled into multimode fiber array.The radi ation from individual ones of emitter regions is optically coupled into individu al ones of fiber array.Total coupling efficiency and fiber output power are 75% and 15W,respectively.
文摘The output radiation from the 100μm×1μm aperture of a high power Laser Diode (LD) is efficiently coupled into a 50μm multimode optical fiber.The fiber output of the high power LD with high brightness and high power density is achieved.The power density is up to 3 6×104W/cm2 and the coupling efficiency is 70%.The extreme divergence and the astigmatism of high power LDs require the optics with complex lens structures and high performance.A double-curved lens with two crossed cylindrical lenses structured on both sides of the glass substrate is used in the coupling system.
基金Project supported by the National Natural Science Foundation of China （Grant No. 61205069）.
文摘Coupling plane wave into a single-mode fiber （SMF） with high and steady coupling efficiency is crucial for fiber- based free-space laser systems, where random angular jitters are the main influencing factors of fiber coupling. In this paper, we verified a new adaptive-optic device named adaptive fiber coupler （AFC） which could compensate angular jitters and improve the SMF coupling efficiency in some degree. Experiments of SMF coupling under the angular jitter situation using AFC have been achieved. Stochastic parallel gradient descent （SPGD） algorithm is employed as the control strategy, of which the iteration rate is 625 Hz. In closed loop, the coupling efficiency keeps above 65% when angular errors are below 80/3tad. The compensation bandwidth is 35 Hz at sine-jitter of 15 ~rad amplitude with average coupling efficiency of above 60%. Also, experiments with simulated turbulence have been studied. The average coupling efficiency increases from 31.97% in open loop to 61.33% in closed loop, and mean square error （MSE） of coupling efficiency drops from 7.43% to 1.75%.
文摘The theoretical investigation of the coupling efficiency of a laser diode to a single mode fiber via a hemispherical lens on the tip of the tapered fiber in the presence of possible transverse offset and angular mismatch is reported.Without the misalignment,coupling efficiency increases with the decreasing of taper length.With the misalignment,this relation is that the coupling efficiency decreases with each kind of offset.
基金National Natural Science Foundation of China(62122027,62075063,62205109,62405092,52202004)Postdoctoral Fellowship Program of CPSF(GZC20230852)+1 种基金State Key Laboratory of Luminescent Materials and Devices(Skllmd-2024-12)China Scholarship Council Grant(202406150002)。
文摘Upconversion nanoparticles(UCNPs)have attracted considerable interest due to their large anti-Stokes shift,offering promising applications in lasing.Here,multi-wavelength upconversion whispering gallery mode(WGM)lasing is demonstrated in silica microspheres coated with NaYF_(4)@NaYbF_(4):1%Tm^(3+)@NaYF_(4)nanoparticles and coupled with tapered fibers.Under continuous-wave 980 nm pumping,low-threshold lasing is achieved across Tm3+transitions from near-infrared to visible,with an ultra-low threshold of 0.61μWfor the 3H_(4)→3H_(6)transition.Additionally,upconversion laser output can also be achieved in Er^(3+)-and Ho^(3+)-activated microspheres.These results establish tapered fiber coupling as a versatile approach for enhancing upconversion microlasers.
基金Youth Science and Technology Research Foundation of Shanxi Province(No.2015021104)Programs for Science and Technology Development of Shanxi Province(No.201703D121028-2)
文摘According to the principle of choosing the light source in the fiber optic sensing measurement,semiconductor laser is used as the light source of fiber optic sensor and single-mode fiber is used as the tail fiber of light source. Based on optical design software Zemax’s pure non-sequential components,a coupling system of semiconductor laser and single-mode fiber is designed. By analyzing the beam characteristics of the semiconductor laser and the coupled mode theory of semiconductor laser and single-mode fiber,the combined lens consists of a ball lens and a collimating lens for the purpose of improving the coupling efficiency and adjusting tolerance. The simulation results show that the coupling efficiency can reach about 78% by using one million ray traces on non-sequential components,while the experimental test result is 69.11%,accordingly,the reasons for the difference between the experiment and the simulation results are analyzed.
基金supported by the National Natural Science Foundation of China(No.12174199)the Wanjing Horizontal Research and Development Fund for Nature(No.HJ1060319960015).
文摘Based on optofluidics and whispering gallery mode(WGM)theory,here an optofluidic refractive index sensor with microtube-coupled suspended core fiber(SCF)is proposed.It solves the issues of general sensors with microcavity-coupled fiber taper such as too fragile,unstable performance due to open coupling,poor portability and repeatability,while overcoming the poor performance of low refractive index sensing in general full-package fiber sensors.The sensor only needs a very small amount of liquid sample(about 1.8 nL).The proposed sensor combines the excellent performance of full package,optofluidics and WGM resonator.The resonant characteristics and sensing performance of the sensor are analyzed and discussed by the theoretical simulation.The simulation results indicate that the sensor has a wide refractive index sensing range(1.330-1.700)and good performance.The resonance wavelength shift has a good linear relationship with the liquid refractive index variation.In the low refractive index region,the sensitivity is 222.5-247.5 nm/RIU,Q-factor is 1.03×10^(3) and the detection limit is 3.64×10^(-4) RIU.In the medium and high refractive index regions,the sensitivity is 564.4-846.2 nm/RIU,Q-factor is up to 8.62×10^(4),and the detection limit can be as low as 1.29×10^(-6) RIU.The sensor exhibits a high sensitivity,a high Q-factor and a very low detection limit.
基金Supported by National Natural Science Foundation of China under Grant No. 10974016
文摘We consider a fiber coupled cavity array. Each cavity is doped with a single two-level atom. By treating the atom-cavity systems as combined polaritonie qubits, we can transform it into a polaritonic qubit-qubit array in the dispersive regime. We show that the four fiber coupled cavity open chain and ring can both generate the four qubit W state and cluster state, and can both transfer one and two qubit arbitrary states. We also discuss the dynamical behaviors of the four fiber coupled cavity array with unequal couplings.
基金supported by the financial support of the National Natural Science Foundation of China (No. 51278483)the Institute of Chinese Academy of Sciences in cooperation projects (No. ZNGZ2011023)the Daqi Technology of Beijing Co. Ltd. (No. 04F0261601)
文摘Experimental design and response surface methodology（RSM） were used to optimize the modification of conditions for glass surface grafting with acrylamide（AM） monomer for preparation of a glass fiber reinforced poly（vinylidene fluoride）（PVDF） composite membrane（GFRP-CM）. The factors considered for experimental design were the UV（ultraviolet）-irradiation time, the concentrations of the initiator and solvent, and the kinds and concentrations of the silane coupling agent. The optimum operating conditions determined were UV-irradiation time of 25 min, an initiator concentration of 0–0.25 wt.%,solvent of N-Dimethylacetamide（DMAC）, and silane coupling agent KH570 with a concentration of 7 wt.%. The obtained optimal parameters were located in the valid region and the experimental confirmation tests conducted showed good accordance between predicted and experimental values. Under these optimal conditions, the water absorption of the grafted modified glass fiber was improved from 13.6% to 23%; the tensile strength was enhanced and the peeling strength of the glass fiber reinforced PVDF composite membrane was improved by 23.7% and 32.6% with an AM concentration at 1 wt.% and 2 wt.%. The surface composition and microstructure of AM grafted glass fiber were studied via several techniques including Field Emission Scanning Electron Microscopy（FESEM）, Fourier transform infrared spectroscopy-attenuated total reflectance（FTIR-ATR） and energy dispersive X-ray spectroscopy（EDX）. The analysis of the EDX and FTIR-ATR results confirmed that the AM was grafted to the glass fiber successfully by detecting and proving the existence of nitrogen atoms in the GFRP-CM.
文摘Integrated diffractive optical mode converter, consisting of a diffractive optical element (DOE) and a slab waveguide, is used for fiber-to-waveguide coupling. The phase of the DOE is generally designed by optimization algorithm. In this paper, the precise design, a new method with one more restrictive way, is adopted to design the diffractive optical mode converter for fiber-to-waveguide coupling. Through this method, the intensity of any point on the output plane is fully filled with the required demand. Compared with what previously published, the coupling loss of the precise designed converter is lower.
基金supported by“Pioneer”and“Leading Goose”Research&Development Program of Zhejiang,China(Grant No.2022C03084)the Natural Science Foundation of China(Grant No.62205296)+1 种基金the Zhejiang Provincial Natural Science Foundation of China(Grant Nos.LQ22F050007 and LQ23F050004)the Ningbo Science and Technology Project,China(Grant No.2021Z030).
文摘In the paper,an optical fiber sensor based on a seven-core fiber composite structure is presented,which enables dual-parameter sensing of bending and temperature.The proposed structure is fabricated by combining the strongly-coupled seven-core fibers(SC-SCFs)and a weakly-coupled seven-core fiber(WC-SCF).The SC-SCF acts as a beam coupler and enhances the Mach-Zehnder interference,while the WC-SCF serves as the enhanced section of another Mach-Zehnder interference.Therefore,the spectrum response of the fiber structure mentioned above exhibits a superposition effect of two Mach-Zehnder interferometers(MZIs).Among them,two dips corresponding to different MZIs are used to measure bending and temperature.The experimental results show the bending sensitivity and temperature sensitivity of the two MZIs are-4.238 nm/m^(-1),-2.263 nm/m^(-1),0.047 nm/℃,and 0.064 nm/,respectively.It proves℃that our sensor is very sensitive to bending.Through the dual-wavelength matrix method,the bending and temperature can be measured simultaneously.With the benefit of the composite structure,low cost,and ease of fabrication,the proposed sensor can be used in harsh environments.
文摘The side-coupler of angle polished method, using angle-polished multimode fiber and optical adhesive, is used to efficiently pump an Yb-doped double-clad fiber laser. The maximum coupling efficiency of 78.6% is achieved by the side-coupler for a multimode fiber with a circular core of 200μm and a double-clad fiber with a 350/400μm D-shaped inner cladding. While laser diodes (LDs) with three side-couplers are simultaneously used as pump sources, maximum output power of 1.38 W and slope efficiency of 48.9% are demonstrated in the fiber laser system.
基金This work was supported by National Science Fund for Distinguished Young Scholars of China (Project 60125513)the Jiangsu Province Natural Science Foundation of China (No. BK2004207).
文摘Using a fiber Bragg grating (FBG) and a Fabry-Perot cavity composed of two fiber Bragg gratings (FBGFP) as its frequency-selective components, a type of single frequency all-fiber ring laser permits oscillation only on one longitudinal mode of the main cavity without modehopping while the cavity length can be up to tens of meters. The salient feature is due to the single narrowband resonance of the FBGFP filter. Such a fiber ring laser is achieved experimentally, and the laser mode is limited inside the single resonance of the FBGFP.
基金This work was supported by the National Natural Science Foundation of China under Grant NO. 60278003 and the National Key Basic Research Special Foundation of China under Grant No.G1999075201,
文摘A Galerkin's method-based numerical procedure is extended to obtain the modal field distribution of multicore photonic crystal fibers for the first time to our knowledge, which can reveal how the air hole size influences the mode coupling and how the coupling strength varies with wavelength. These results will be helpful in the future design of multicore photonic crystal fibers with proper guidance properties.
基金This work was supported by the Scientific Research Foundation of Harbin Institute of Technology.
文摘At liquid-nitrogen temperature, at 10-kHz pulse repetition rate, Q-switched 36-ns pulses with average output power of 4 W at 2.05 μm and 4.5-W continuous wave output power with a total optical-optical conversion efficiency of 30%, were achieved from a 6% Tm, 0.5% Ho:YLiF4 laser. This laser was end-pumped by a fiber-coupled laser diode emitting up to 15 W around 792 nm. The 1-m-long optical fiber carrying the pump radiation has a core diameter of 700 μm with a numerical aperture of 0.22.
文摘Based on the high-speed development of the fiber laser in recent years, the development of researching 915 nm semiconductor laser as main pumping sources of the fiber laser is at a high speed. Because the beam quality of the laser diode is very poor, the 915 nm laser diode is generally based on optical fiber coupling module to output the laser. Using the beam-shaping and fiber-coupling technology to improve the quality of output beam light, we present a kind of high-power and high-brightness semiconductor laser module, which can output 13.22 W through the optical fiber. Based on 915 nm GaAs semiconductor laser diode which has output power of 13.91 W, we describe a thoroughly detailed procedure for reshaping the beam output from the semiconductor laser diode and coupling the beam into the optical fiber of which the core diameter is 105 μm and the numerical aperture is 0.18. We get 13.22 W from the output fiber of the module at 14.5 A, the coupling efficiency of the whole module is 95.03% and the brightness is 1.5 MW/cm2-str. The output power of the single chip semiconductor laser module achieves the advanced level in the domestic use.
基金supported by the National "863" Program of China (No.2009AA01Z216)the Program for New Century Excellent Talents in University (NCET)
文摘The coupling between guided optical waves in magneto-optic fiber Bragg gratings （MFBGs） with linear birefringence is investigated using the eigen-mode and coupled-mode approaches. The relationship between the polarization-dependent loss （PDL） and the eigen states of polarization （SOPs） in the MFBGs is discussed. Only the MFBCs with low linear birefringence are applied to the peak PDL-based magnetic field measurement, after which the linear dynamic range is determined using the relative magnitude of linear and magnetically induced circular birefringence. In this letter, a theoretical model is presented to explain the experimental results and help develop novel MFBG-based devices.
文摘We report a high-power ultra-narrow fiber-coupled diode laser using a Faraday anomalous dispersion optical filter(FADOF) as an external cavity element.An external cavity suitable for both the fiber-coupled package and FADOF configuration has been proposed.Using a87Rb-based FADOF as the frequency-selective element,we realized a 103 W continuous laser output with a uniform circular beam.The center wavelength was precisely locked at the D2line of the Rb resonance,and the bandwidth was narrowed from 1.8 nm (free-running,full width at half maximum (FWHM)) to0.013 nm (6.9 GHz,FWHM).The side mode suppression ratio reached 31 dB.Such diode lasers with precise wavelength and high spectral brightness have critical applications in many fields,such as high-energy gas laser pumping,spinexchange optical pumping,Raman spectroscopy and nonlinear optics.
基金supported by the National Natural Science Foundation of China(No.61422108)the Natural Science Foundation of Jiangsu Province(No.BK20160082)+1 种基金the Jiangsu Provincial Program for High-level Talents in Six Areas(No.DZXX-030)the Fundamental Research Funds for Central Universities(Nos.NE2017002 and NS2016037)
文摘A polarization-maintained coupled optoelectronic oscillator（COEO） with its performance significantly improved by a short-length unpumped erbium-doped fiber（EDF） is reported and experimentally investigated.A 10 GHz optical pulse train with a supermode suppression ratio of 61.8 d B and a 10 GHz radio frequency signal with a sidemode suppression ratio of 94 d B and a phase noise of-121.9 d Bc∕Hz at 10 k Hz offset are simultaneously generated. Thanks to saturable absorption of the 1 m unpumped EDF, which introduces relatively large cavity loss to the undesired modes and noise, the supermode suppression ratio and the phase noise are improved by 9.4 and 7.9 d B, respectively.
基金Okinawa Institute of Science and Technology Graduate University(OIST)
文摘Tapered fibers with diameters ranging from 1 to 4 μm are widely used to excite the whispering-gallery(WG)modes of microcavities. Typically, the transmission spectrum of a WG cavity coupled to a waveguide around a resonance assumes a Lorentzian dip morphology due to resonant absorption of the light within the cavity. In this paper, we demonstrate that the transmission spectra of a WG cavity coupled with an ultrathin fiber(500–700 nm)may exhibit both Lorentzian dips and peaks, depending on the gap between the fiber and the microcavity. By considering the large scattering loss of off-resonant light from the fiber within the coupling region, this phenomenon can be attributed to partially resonant light bypassing the lossy scattering region via WG modes, allowing it to be coupled both to and from the cavity, then manifesting as Lorentzian peaks within the transmission spectra.This implies the system could be implemented within a bandpass filter framework.
