This study fabricated textures on the stator surface of a traveling wave ultrasonic motor(USM)using laser and investigated the tribological behavior of a polytetrafluoroethylene(PTFE)composite friction material and st...This study fabricated textures on the stator surface of a traveling wave ultrasonic motor(USM)using laser and investigated the tribological behavior of a polytetrafluoroethylene(PTFE)composite friction material and stator.Initially,the effect of textures with different densities was tested.As the results suggested,the generation of large transfer films of PTFE composite was prevented by laser surface texturing,and adhesive wear reduced notably despite the insignificant decrease in load capacity and efficiency.Next,the 100-h test was performed to further study the effects of texture.Worn surface and wear debris were observed to discuss wear mechanisms.After 100 h,the form of wear debris changed into particles.The wear mechanisms of friction material sliding against the textured stator were small size fatigue and slight abrasive wear.The wear height of friction material decreased from 3.8μm to 1.1μm.This research provides a method to reduce the wear of friction materials used in travelling wave USMs.展开更多
Ultrasonic-Assisted Grinding(UAG)is a novel manufacturing technology that shows promising promise for use in processing Ceramic Matrix Composites(CMCs).Nevertheless,analyzing the material removal process of CMCs with ...Ultrasonic-Assisted Grinding(UAG)is a novel manufacturing technology that shows promising promise for use in processing Ceramic Matrix Composites(CMCs).Nevertheless,analyzing the material removal process of CMCs with multidirectional structure during UAG is challenging,impeding the progress and improvement of the UAG process.This work examined the impact of ultrasonic vibration on the dynamic mechanical characteristics during processing.Additionally,we experimentally elucidated the material removal mechanism of CMCs during the scratching process under the influence of vertical vibration.The results indicate that the introduction of ultrasonic vibration causes a strain rate effect,resulting in a modification of the material removal mechanism,subsequently impacting the processing quality.Ultrasonic vibration increases the dynamic strength and brittleness of the fibers in CMCs,leading to more cracks at fracture,which changes from the original bending fracture to shear fracture.In addition,ultrasonic vibration can effectively inhibit the impact of scratching depth and anisotropy on the removal mechanism of CMCs,resulting in a more uniform surface of CMCs after processing.展开更多
Standardization is necessary for the early industrialization of the new materials and technology.It is achieved by having agreed practices for the measurement of properties and other characteristics.The promising use ...Standardization is necessary for the early industrialization of the new materials and technology.It is achieved by having agreed practices for the measurement of properties and other characteristics.The promising use of graphene-based materials in fields like electronics,energy,and composites has resulted in standards for their nomenclature,the measurement of key characteristics,and their specification,etc.Among these,standards for measuring the key characteristics are crucial.The critical parameters are the number of layers,the type and concentration of defects and functional groups,elemental composition,sheet resistance,and carrier mobility.Standards for characterizing these have been analyzed by the International Organization for Standardization Technical Committee in ISO/TC229 and the International Electrotechnical Commission Technical Committee in IEC/TC113.These give details of applicable or preferred samples,the fundamental principles of the techniques,specific precautions,and points for attention in the relevant standards.The pivotal role of the ISO/TC229 and IEC/TC113 standards is considered and challenges and future trends are outlined.展开更多
CO_(2) capture and utilization(CCU)technologies have been recognized as crucial strategies for mitigating global warming,reducing carbon emission,and promoting resource circularity.As such,the design and development o...CO_(2) capture and utilization(CCU)technologies have been recognized as crucial strategies for mitigating global warming,reducing carbon emission,and promoting resource circularity.As such,the design and development of related materials have attracted considerable research attention.Carbon-based materials,characterized by tunable pore structures,abundant active sites,high specific surface area,and excellent chemical stability,demonstrate significant potential for applications in CO_(2) capture and utilization.This review systematically analyzes the adsorption behaviors and performance variations of typical carbon materials,including activated carbon,porous carbon,graphene,and carbon nanotubes during CO_(2) capture processes.Concerning CO_(2) utilization,emphasis is placed on recent advances in the catalytic applications of carbon-based materials in key reactions such as methanation,reverse water-gas shift,dry reforming of methane,and alcohol synthesis.Moreover,the benefits and drawbacks of carbon materials in terms of CO_(2) adsorption capacity,catalytic activity,and stability are thoroughly evaluated,and their potential applications in integrated CO_(2) capture and utilization technologies are discussed.Finally,key strategies for enhancing the performance of carbonaceous materials through structural modulation and surface modification are elucidated.This review aims to provide theoretical guidance for the future development and large-scale implementation of carbon-based materials in CCU technologies.展开更多
Moisture electricity generation(MEG)has emerged as a sustainable and versatile energy-harvesting technology capable of converting ubiquitous environmental moisture into electrical energy,which holds great promise for ...Moisture electricity generation(MEG)has emerged as a sustainable and versatile energy-harvesting technology capable of converting ubiquitous environmental moisture into electrical energy,which holds great promise for renewable energy and constructing self-powered electronics.In this review,we begin by outlining the fundamental mechanisms—ion diffusion,electric double layer formation,and streaming potential—that govern charge transport for MEG in moist environments.A comprehensive survey of material innovations follows,highlighting breakthroughs in carbon-based materials,conductive polymers,hydrogels,and bio-inspired systems that enhance MEG performance,scalability,and biocompatibility.We then explore a range of device architectures,from planar and layered systems to flexible,miniaturized,and textile-integrated designs,engineered for both energy conversion and sensor integration.Key challenges are analyzed,along with strategies for overcoming them.We conclude with a forward-looking perspective on future directions,including hybrid energy systems,AI-assisted material design,and real-world deployment.This review presents a timely and comprehensive overview of MEG technologies and their trajectory toward practical and sustainable energy solutions.展开更多
The capture of atmospheric carbon dioxide by adsorbents is an important strategy to deal with the greenhouse effect.Compared with traditional CO_(2) adsorption materials like activated carbon,silica gel,and zeolite mo...The capture of atmospheric carbon dioxide by adsorbents is an important strategy to deal with the greenhouse effect.Compared with traditional CO_(2) adsorption materials like activated carbon,silica gel,and zeolite molecular sieves,covalent organic frameworks(COFs)have excellent thermal and chemical stabilities and can be produced in many different forms.Using their different possible construction units,ordered structures for specific applications can be produced,giving them broad prospects in fields such as gas storage.This review analyzes the different types of COFs that have been synthesized and their different methods of CO_(2) capture.It then discusses different ways to increase CO_(2) adsorption by changing the internal structure of COFs and modifying their surfaces.The limitations of COF-derived carbon materials in CO_(2) capture are reviewed and,finally,the key role of machine learning and computational simulation in improving CO_(2) adsorption is mentioned,and the current status and future possible uses of COFs are summarized.展开更多
Investments in eco-friendly,recyclable material solutions and innovation in bio-based nonwovens are increasingly shaping the next generation of automotive interiors.The development of nonwoven materials and associated...Investments in eco-friendly,recyclable material solutions and innovation in bio-based nonwovens are increasingly shaping the next generation of automotive interiors.The development of nonwoven materials and associated technologies is likely to lead to even wider adoption in the automotive industry,driven by rising global vehicle production,particularly in the growing electric vehicle(EV)segment,and an intensified focus on sustainable solutions.展开更多
The reactive materials filled structure(RMFS)is a structural penetrator that replaces high explosive(HE)with reactive materials,presenting a novel self-distributed initiation,multiple deflagrations behavior during pen...The reactive materials filled structure(RMFS)is a structural penetrator that replaces high explosive(HE)with reactive materials,presenting a novel self-distributed initiation,multiple deflagrations behavior during penetrating multi-layered plates,and generating a multipeak overpressure behind the plates.Here analytical models of RMFS self-distributed energy release and equivalent deflagration are developed.The multipeak overpressure formation model based on the single deflagration overpressure expression was promoted.The impact tests of RMFS on multi-layered plates at 584 m/s,616 m/s,and819 m/s were performed to validate the analytical model.Further,the influence of a single overpressure peak and time intervals versus impact velocity is discussed.The analysis results indicate that the deflagration happened within 20.68 mm behind the plate,the initial impact velocity and plate thickness are the crucial factors that dominate the self-distributed multipeak overpressure effect.Three formation patterns of multipeak overpressure are proposed.展开更多
Photocatalytic nitrogen fixation (PNF) is a promising alternative to the Haber-Bosch process.It achieves green ammonia production by utilizing solar energy for nitrogen fixation under mild conditions.While nanoscale p...Photocatalytic nitrogen fixation (PNF) is a promising alternative to the Haber-Bosch process.It achieves green ammonia production by utilizing solar energy for nitrogen fixation under mild conditions.While nanoscale photocatalysts offer enhanced performance due to their high surface area and abundant active sites,their small size makes them difficult to recover and prone to agglomeration.These bottlenecks severely limit industrial application.A promising solution is to immobilize the catalysts onto support surfaces.This paper provides a systematic review of recent advances in the design of immobilized photocatalysts for ammonia synthesis.It begins by outlining the key benefits of immobilization strategies,particularly in improving catalyst stability,recyclability,and overall photocatalytic performance.The working mechanisms and features of various immobilization techniques are then categorized and explained,covering physical adsorption/deposition,chemical bonding,in situ growth,and hybrid physico-chemical methods.Supported materials and common substrate types are also summarized.Furthermore,the widely used configurations of photoreactors suitable for immobilized systems are introduced.Finally,the review identifies current research limitations and challenges,and offers perspectives on future developments in the field of immobilized photocatalysis.展开更多
Coal cinder is an abundant byproduct of the extensive consumption of coal in industrial production and daily life.Making full use of the cinder is conducive to a low-carbon economy.In this study,inspired by the burnin...Coal cinder is an abundant byproduct of the extensive consumption of coal in industrial production and daily life.Making full use of the cinder is conducive to a low-carbon economy.In this study,inspired by the burning of coal,a new method for constructing a silica-based composite porous material(SiO_(2)-CPM)was developed by combusting a siloxane-modified anthracite coal gel(CSiO_(2) gel).During this process,the combustion product was directly converted into a porous material,and the calorific value of the coal remained nearly unchanged(~98%of the original calorific value was retained),demonstrating the viability of this method for energy-efficient applications.The SiO_(2)-CPM exhibited an ultra-low thermal conductivity(0.036 W/(m·K)at room temperature),outperforming conventional insulation materials(e.g.,cotton~0.05 W/(m·K)).Additionally,it showed enhanced mechanical strength(fracture stress of 41.8 kPa)compared to the powder state of the coal cinder.Experimental results indicate that the amount of siloxane,structure-directing agent,and an acidic environment were critical for mechanical enhancement.The SiO_(2)-CPM showed good dimensional stability against thermal expansion and exhibited excellent thermal insulation and fire resistance even at 900℃.Meanwhile,the SiO_(2)-CPM with complex geometry could be easily fabricated using this method owing to the excellent shaping ability of the CSiO_(2) gel.Compared to conventional methods such as sol-gel synthesis or freeze-drying,this approach for fabricating SiO_(2)-CPM is simpler and cost-effective and allows the direct utilization of coal cinder post-combustion.展开更多
To solve the problem of abnormal abrasion of Cu-Based Friction Materials(CBFMs),Bionic Non-Smooth Surface(BNS)on friction surface of CBFMs was constructed based on bionic principles,and the optimal bionic prototype wa...To solve the problem of abnormal abrasion of Cu-Based Friction Materials(CBFMs),Bionic Non-Smooth Surface(BNS)on friction surface of CBFMs was constructed based on bionic principles,and the optimal bionic prototype was selected by Finite Element Method(FEM).In addition,the bionic parameters were optimized by Response Surface Method(RSM).Samples holding BNS were prepared by Laser Processing,tribological properties were tested by a Friction and Wear Tester and worn surface morphology was characterized by a Scanning Electron Microscope(SEM).The results showed that BNS on friction surface could regulate the stress distribution and alleviate the peak stress.Among all samples,the coupled texture of pit-hexagonal got the minimum peak stress.During braking,bionic texture could also collect wear debris or change the motion forms from sliding to rotation,which can reduce abnormal abrasion.The wear rate was reduced by 19.31%.The results in this paper can provide a new idea for enhancing the tribological properties of CBFMs,and can also lay the foundation for further research of bionic tribology.展开更多
Though the formation of polysulfide is desirable,as it contributes to the capacity build-up,it must not leak into the electrolyte.The loss of polysulfide causes capacity fade,a change in the local chemistry of the ele...Though the formation of polysulfide is desirable,as it contributes to the capacity build-up,it must not leak into the electrolyte.The loss of polysulfide causes capacity fade,a change in the local chemistry of the electrolyte,and anode poisoning.Constant efforts are in progress to find suitable polysulfide-absorbing materials;however,the magical polysulfide absorber is yet to be discovered or developed.Experimental methods alone often fall short in accelerating the investigations may be due to the complex Nature of the testing.This review focuses on the importance of computational methods,particularly density functional theory(DFT),in screening suitable polysulfide absorbers.It highlights the critical role of anchoring materials in improving Na-S battery performance,including pristine and doped graphene,metal–organic frameworks,carbon Nanofibers,vanadium disulfide,MXenes,and metal sulfides.By examining adsorption energies,charge transfer mechanisms,and catalytic properties,this review provides insights into the design of advanced materials that can effectively immobilize polysulfides and enhance battery stability.The review aims to guide future research efforts toward the development of high-performance RT Na-S batteries through a comprehensive understanding of the polysulfide-absorbing materials.展开更多
Cement stands as a dominant contributor to global energy consumption and carbon emissions in the construction industry.With the upgrading of infrastructure and the improvement of building standards,traditional cement ...Cement stands as a dominant contributor to global energy consumption and carbon emissions in the construction industry.With the upgrading of infrastructure and the improvement of building standards,traditional cement fails to reconcile ecological responsibility with advanced functional performance.By incorporating tailored fillers into cement matrices,the resulting composites achieve enhanced thermoelectric(TE)conversion capabilities.These materials can harness solar radiation from building envelopes and recover waste heat from indoor thermal gradients,facilitating bidirectional energy conversion.This review offers a comprehensive and timely overview of cementbased thermoelectric materials(CTEMs),integrating material design,device fabrication,and diverse applications into a holistic perspective.It summarizes recent advancements in TE performance enhancement,encompassing fillers optimization and matrices innovation.Additionally,the review consolidates fabrication strategies and performance evaluations of cement-based thermoelectric devices(CTEDs),providing detailed discussions on their roles in monitoring and protection,energy harvesting,and smart building.We also address sustainability,durability,and lifecycle considerations of CTEMs,which are essential for real-world deployment.Finally,we outline future research directions in materials design,device engineering,and scalable manufacturing to foster the practical application of CTEMs in sustainable and intelligent infrastructure.展开更多
Responsive colorimetric materials exhibit significant potential for application in fields such as smart food packaging and wound monitoring.The functional integration of pH-indicators with material carriers enables br...Responsive colorimetric materials exhibit significant potential for application in fields such as smart food packaging and wound monitoring.The functional integration of pH-indicators with material carriers enables breakthrough applications in nontraditional domains.In this study,we developed a novel material covalently grafted with a pH indicator that exhibited naked-eye pH-responsive color shifts.The covalent grafting of pH-responsive bromothymol blue onto carboxymethyl cellulose(CMC)was confirmed using advanced characterization techniques,including Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy.The pH-sensitive chromophore was covalently immobilized onto the CMC matrix through esterification,thereby establishing firm chemical conjugation.Moreover,a superior color-changing performance was achieved within several minutes in response to different pH values.The reusability and stability of this material offer distinct advantages over single-use pH test strips.pH-responsive colorimetric materials hold promise for efficient,noninvasive monitoring in intelligent packaging(food freshness),medical diagnostics(wound status,infections),biosensing,and environmental applications.展开更多
A soft X-ray energy materials research beamline(BL20U2),a branch of energy materials beamline(E-line),has been constructed in the Shanghai Synchrotron Radiation Facility(SSRF)Phase-II project.It is now operational for...A soft X-ray energy materials research beamline(BL20U2),a branch of energy materials beamline(E-line),has been constructed in the Shanghai Synchrotron Radiation Facility(SSRF)Phase-II project.It is now operational for soft X-ray resonant emission spectroscopy(RXES)and soft X-ray resonant elastic scattering(REXS)investigations.Optical optimization was implemented for high performance,e.g.,photon flux,energy-resolving power,and focus spot size.RXES experiments show that the energy range extends from 150 to 1500 eV.The elastic peak measured near titanium absorption edge(@445 eV)indicates an energy resolution of the RXES spectrometer of 65 meV.The measured photon flux is 3×10^(12)photons/s at 244 eV at the RXES sample position for an SSRF electron energy of 3.5 GeV and a projected ring current as 300 mA.The spot size at the RXES sample position is 23μm in the horizontal direction and 7.9μm in the vertical direction,respectively.Moreover,the angular resolution of elastic REXS scatterometer reaches 0.005°through measurement of X-ray reflection from the single-crystal silicon wafers.A sample of the REXS scatterometer is vibrationally decoupled from its chamber and cooled using copper braids connected from an open cycle liquid helium cryo reservoir,whereas the minimum sample temperature is below 15 K.展开更多
The mechanical performance of exceedingly soft materials such as Ag is significantly influenced by various working conditions.Therefore,this study systematically investigates the effects of crack geometry,substrate cr...The mechanical performance of exceedingly soft materials such as Ag is significantly influenced by various working conditions.Therefore,this study systematically investigates the effects of crack geometry,substrate crystal orientation,and indenter shape on crack propagation.The mechanical response of Ag is analyzed using the quasi-continuum(QC)method.A pre-crack with a predefined depth and angle was introduced to initiate fracture behavior.The results show that when the pre-crack height is 50 A,the crack propagates rapidly as the imprint depth increases from0 to 7 A,grows steadily up to 15 A,and then accelerates sharply between 15 and 20 A.For other pre-crack heights,crack propagation occurs at a relatively faster rate.Substrates with[100],[010],and[001]crystal orientations promote crack extension,while the onset of plastic deformation(referred to as the yield point in this study)and the fracture strength both increase with increasing pre-crack height.The yield point,fracture strength,and stress intensity factors are highly sensitive to the pre-crack height.When the pre-crack angle is 90○,the fracture strength reaches its maximum of 0.2%higher than that of the uncracked sample-whereas at 0○,it reaches its minimum,still 53.8%higher than that of the uncracked sample.The sample model is conducted using AutoCAD software.The optimized quasicontinuum(QC)method is used to investigate the effects of different crack geometries,substrate crystal orientations,and indenter shapes on the crack extension of Ag material.Baskes and Dow(FBD)potential is borrowed to describe the interaction forces between Ag-Ag,Ni-Ag,and Ni-Ni.展开更多
Lattice materials have demonstrated promising potential in engineering applications owing to their exceptional lightweight,high specific strength,and tunable mechanical properties.However,the traditional homogenizatio...Lattice materials have demonstrated promising potential in engineering applications owing to their exceptional lightweight,high specific strength,and tunable mechanical properties.However,the traditional homogenization methods based on the classical elasticity theory struggle to accurately describe the non-classical mechanical behaviors of lattice materials,especially when dealing with complex unit-cell geometries featured by non-symmetric configurations or non-single central node connections.In response to this limitation,this study establishes a generalized homogenization model based on the micropolar theory framework,employing Hill's boundary conditions to precisely predict the equivalent moduli of complex lattice materials.By introducing the independent rotational degree of freedom(DOF)characteristic of the micropolar theory,the proposed model successfully overcomes the limitation of conventional methods in accurately describing the asymmetric deformation and scale effects.We initially calculate the constitutive relations of two-dimensional(2D)cross-shaped multi-node chiral lattices and subsequently extend the method to three-dimensional(3D)lattices,successfully predicting the mechanical properties of both traditional and eccentric body-centered cubic(BCC)lattices.The theoretical model is validated through the finite element numerical verification which shows excellent consistency with the theoretical predictions.A further parametric study investigates the influence of geometric parameters,revealing the underlying size-effect mechanism.This paper provides a reliable theoretical tool for the design and property optimization of complex lattice materials.展开更多
Protective hardware is essential for mitigating damage caused by unavoidable falls in humanoid robots.Despite notable progress in fall protection hardware,the theoretical foundation for modeling and the feasibility of...Protective hardware is essential for mitigating damage caused by unavoidable falls in humanoid robots.Despite notable progress in fall protection hardware,the theoretical foundation for modeling and the feasibility of conducting full-scale fall experiments on robots or their surrogates remain somewhat limited.This paper proposes a method for optimizing the thickness of Expandable Polyethylene(EPE),which is used as back protection for the Chubao humanoid robot,based on small-scale impact test data to predict full-scale behavior.The optimal thickness is defined as a balance between compact design and protective effectiveness.An equivalent impact model characterized by four parameters:contact area S,mass m,fall height h,and cushioning material thickness d is introduced to describe impact conditions.The relationship between the peak impact acceleration ap and material thickness d,which forms the core of the method and gives rise to the name AP-D,is analyzed through their plotted curves.After introducing three characteristic parameters and two correction fac-tors,the relationship among the aforementioned variables is derived.Subsequently,both the optimal thickness do and its corresponding peak impact acceleration aop are predicted via nonlinear and linear regression models.Finally,the accuracy and effectiveness of the theoretically derived optimal thickness are validated on both a dummy and the actual robot.With the cushioning material applied,the peak chest acceleration is reduced to 41.57g for the dummy and 32.08g for the robot.展开更多
As electronic technology continues to evolve towards miniaturization and integration,the demand for micro-refrigeration technology in microelectronic systems is increasing.Ferroelectric(FE)refrigeration technology bas...As electronic technology continues to evolve towards miniaturization and integration,the demand for micro-refrigeration technology in microelectronic systems is increasing.Ferroelectric(FE)refrigeration technology based on the electrocaloric effect(ECE)has emerged as a highly promising candidate in this field,due to its advantages of high energy efficiency,simple structure,easy miniaturization,low cost,and environmental friendliness.The EC performance of FE materials essentially depends on the phase transition features under the coupled electric and thermal fields,making the E–T phase diagram a core tool for decoding the underlying mechanism of ECE.This paper reviews the development of EC materials,focusing on the comprehensive study of E–T phase diagrams.By correlating the microscopic phase structure of FE materials with the macroscopic physical properties,it clarifies the manipulation mechanism for enhanced ECE performance,providing theoretical support for the targeted design of high-performance EC materials.In the future,the introduction of data-driven methods is expected to enable the high-throughput construction of FE phase diagrams,thereby accelerating the optimization of high-performance EC materials and promoting the practical application of FE refrigeration technology.展开更多
基金Natural Science Foundation of Zhejiang Province(No.LQ18E050002)Natural Science Foundation of Ningbo(No.2017A610076)Beijing Key Laboratory of Long-life Technology of Precise Rotation and Transmission Mechanisms(No.BZ0388201702)for providing research funds and this study was sponsored by K.C.Wong Magna Fund in Ningbo University.
文摘This study fabricated textures on the stator surface of a traveling wave ultrasonic motor(USM)using laser and investigated the tribological behavior of a polytetrafluoroethylene(PTFE)composite friction material and stator.Initially,the effect of textures with different densities was tested.As the results suggested,the generation of large transfer films of PTFE composite was prevented by laser surface texturing,and adhesive wear reduced notably despite the insignificant decrease in load capacity and efficiency.Next,the 100-h test was performed to further study the effects of texture.Worn surface and wear debris were observed to discuss wear mechanisms.After 100 h,the form of wear debris changed into particles.The wear mechanisms of friction material sliding against the textured stator were small size fatigue and slight abrasive wear.The wear height of friction material decreased from 3.8μm to 1.1μm.This research provides a method to reduce the wear of friction materials used in travelling wave USMs.
基金supported by the National Science Foundation for Distinguished Young Scholars of China(No.52325506)the Fundamental Research Funds for the Central Universities(No.DUT22LAB501)。
文摘Ultrasonic-Assisted Grinding(UAG)is a novel manufacturing technology that shows promising promise for use in processing Ceramic Matrix Composites(CMCs).Nevertheless,analyzing the material removal process of CMCs with multidirectional structure during UAG is challenging,impeding the progress and improvement of the UAG process.This work examined the impact of ultrasonic vibration on the dynamic mechanical characteristics during processing.Additionally,we experimentally elucidated the material removal mechanism of CMCs during the scratching process under the influence of vertical vibration.The results indicate that the introduction of ultrasonic vibration causes a strain rate effect,resulting in a modification of the material removal mechanism,subsequently impacting the processing quality.Ultrasonic vibration increases the dynamic strength and brittleness of the fibers in CMCs,leading to more cracks at fracture,which changes from the original bending fracture to shear fracture.In addition,ultrasonic vibration can effectively inhibit the impact of scratching depth and anisotropy on the removal mechanism of CMCs,resulting in a more uniform surface of CMCs after processing.
文摘Standardization is necessary for the early industrialization of the new materials and technology.It is achieved by having agreed practices for the measurement of properties and other characteristics.The promising use of graphene-based materials in fields like electronics,energy,and composites has resulted in standards for their nomenclature,the measurement of key characteristics,and their specification,etc.Among these,standards for measuring the key characteristics are crucial.The critical parameters are the number of layers,the type and concentration of defects and functional groups,elemental composition,sheet resistance,and carrier mobility.Standards for characterizing these have been analyzed by the International Organization for Standardization Technical Committee in ISO/TC229 and the International Electrotechnical Commission Technical Committee in IEC/TC113.These give details of applicable or preferred samples,the fundamental principles of the techniques,specific precautions,and points for attention in the relevant standards.The pivotal role of the ISO/TC229 and IEC/TC113 standards is considered and challenges and future trends are outlined.
基金Supported by National Key R&D Program of China(2025YFE0109700)the National Natural Science Foundation of China(52106150)。
文摘CO_(2) capture and utilization(CCU)technologies have been recognized as crucial strategies for mitigating global warming,reducing carbon emission,and promoting resource circularity.As such,the design and development of related materials have attracted considerable research attention.Carbon-based materials,characterized by tunable pore structures,abundant active sites,high specific surface area,and excellent chemical stability,demonstrate significant potential for applications in CO_(2) capture and utilization.This review systematically analyzes the adsorption behaviors and performance variations of typical carbon materials,including activated carbon,porous carbon,graphene,and carbon nanotubes during CO_(2) capture processes.Concerning CO_(2) utilization,emphasis is placed on recent advances in the catalytic applications of carbon-based materials in key reactions such as methanation,reverse water-gas shift,dry reforming of methane,and alcohol synthesis.Moreover,the benefits and drawbacks of carbon materials in terms of CO_(2) adsorption capacity,catalytic activity,and stability are thoroughly evaluated,and their potential applications in integrated CO_(2) capture and utilization technologies are discussed.Finally,key strategies for enhancing the performance of carbonaceous materials through structural modulation and surface modification are elucidated.This review aims to provide theoretical guidance for the future development and large-scale implementation of carbon-based materials in CCU technologies.
基金supported by the National Natural Science Foundation of China(52305388,BE0200030)Shanghai Pujiang Program(22PJ1407600)+1 种基金SJTU Explore X programShanghai Jiao Tong University Initiative Scientific Research Program(WH220402021)。
文摘Moisture electricity generation(MEG)has emerged as a sustainable and versatile energy-harvesting technology capable of converting ubiquitous environmental moisture into electrical energy,which holds great promise for renewable energy and constructing self-powered electronics.In this review,we begin by outlining the fundamental mechanisms—ion diffusion,electric double layer formation,and streaming potential—that govern charge transport for MEG in moist environments.A comprehensive survey of material innovations follows,highlighting breakthroughs in carbon-based materials,conductive polymers,hydrogels,and bio-inspired systems that enhance MEG performance,scalability,and biocompatibility.We then explore a range of device architectures,from planar and layered systems to flexible,miniaturized,and textile-integrated designs,engineered for both energy conversion and sensor integration.Key challenges are analyzed,along with strategies for overcoming them.We conclude with a forward-looking perspective on future directions,including hybrid energy systems,AI-assisted material design,and real-world deployment.This review presents a timely and comprehensive overview of MEG technologies and their trajectory toward practical and sustainable energy solutions.
文摘The capture of atmospheric carbon dioxide by adsorbents is an important strategy to deal with the greenhouse effect.Compared with traditional CO_(2) adsorption materials like activated carbon,silica gel,and zeolite molecular sieves,covalent organic frameworks(COFs)have excellent thermal and chemical stabilities and can be produced in many different forms.Using their different possible construction units,ordered structures for specific applications can be produced,giving them broad prospects in fields such as gas storage.This review analyzes the different types of COFs that have been synthesized and their different methods of CO_(2) capture.It then discusses different ways to increase CO_(2) adsorption by changing the internal structure of COFs and modifying their surfaces.The limitations of COF-derived carbon materials in CO_(2) capture are reviewed and,finally,the key role of machine learning and computational simulation in improving CO_(2) adsorption is mentioned,and the current status and future possible uses of COFs are summarized.
文摘Investments in eco-friendly,recyclable material solutions and innovation in bio-based nonwovens are increasingly shaping the next generation of automotive interiors.The development of nonwoven materials and associated technologies is likely to lead to even wider adoption in the automotive industry,driven by rising global vehicle production,particularly in the growing electric vehicle(EV)segment,and an intensified focus on sustainable solutions.
基金the support received from the National Natural Science Foundation of China(Grant No.12302460)the State Key Laboratory of Explosion Science and Safety Protection(Grant No.YBKT24-02)。
文摘The reactive materials filled structure(RMFS)is a structural penetrator that replaces high explosive(HE)with reactive materials,presenting a novel self-distributed initiation,multiple deflagrations behavior during penetrating multi-layered plates,and generating a multipeak overpressure behind the plates.Here analytical models of RMFS self-distributed energy release and equivalent deflagration are developed.The multipeak overpressure formation model based on the single deflagration overpressure expression was promoted.The impact tests of RMFS on multi-layered plates at 584 m/s,616 m/s,and819 m/s were performed to validate the analytical model.Further,the influence of a single overpressure peak and time intervals versus impact velocity is discussed.The analysis results indicate that the deflagration happened within 20.68 mm behind the plate,the initial impact velocity and plate thickness are the crucial factors that dominate the self-distributed multipeak overpressure effect.Three formation patterns of multipeak overpressure are proposed.
基金support for carrying out this work was provided by the Doctoral Research Foundation of Weifang University(2024BS20)Science and Technology Development Plan Foundation of Weifang(2024GX017).
文摘Photocatalytic nitrogen fixation (PNF) is a promising alternative to the Haber-Bosch process.It achieves green ammonia production by utilizing solar energy for nitrogen fixation under mild conditions.While nanoscale photocatalysts offer enhanced performance due to their high surface area and abundant active sites,their small size makes them difficult to recover and prone to agglomeration.These bottlenecks severely limit industrial application.A promising solution is to immobilize the catalysts onto support surfaces.This paper provides a systematic review of recent advances in the design of immobilized photocatalysts for ammonia synthesis.It begins by outlining the key benefits of immobilization strategies,particularly in improving catalyst stability,recyclability,and overall photocatalytic performance.The working mechanisms and features of various immobilization techniques are then categorized and explained,covering physical adsorption/deposition,chemical bonding,in situ growth,and hybrid physico-chemical methods.Supported materials and common substrate types are also summarized.Furthermore,the widely used configurations of photoreactors suitable for immobilized systems are introduced.Finally,the review identifies current research limitations and challenges,and offers perspectives on future developments in the field of immobilized photocatalysis.
基金supported by the National Natural Science Foundation of China(No.52573220)the National Key R&D Program of China(No.2023YFC3404201)+1 种基金the Fundamental Research Funds for the Central Universities(No.FRF-IDRY-GD24-005)the State Key Laboratory of Solid Waste Reuse for Building Materials(No.SWR-2022-009).
文摘Coal cinder is an abundant byproduct of the extensive consumption of coal in industrial production and daily life.Making full use of the cinder is conducive to a low-carbon economy.In this study,inspired by the burning of coal,a new method for constructing a silica-based composite porous material(SiO_(2)-CPM)was developed by combusting a siloxane-modified anthracite coal gel(CSiO_(2) gel).During this process,the combustion product was directly converted into a porous material,and the calorific value of the coal remained nearly unchanged(~98%of the original calorific value was retained),demonstrating the viability of this method for energy-efficient applications.The SiO_(2)-CPM exhibited an ultra-low thermal conductivity(0.036 W/(m·K)at room temperature),outperforming conventional insulation materials(e.g.,cotton~0.05 W/(m·K)).Additionally,it showed enhanced mechanical strength(fracture stress of 41.8 kPa)compared to the powder state of the coal cinder.Experimental results indicate that the amount of siloxane,structure-directing agent,and an acidic environment were critical for mechanical enhancement.The SiO_(2)-CPM showed good dimensional stability against thermal expansion and exhibited excellent thermal insulation and fire resistance even at 900℃.Meanwhile,the SiO_(2)-CPM with complex geometry could be easily fabricated using this method owing to the excellent shaping ability of the CSiO_(2) gel.Compared to conventional methods such as sol-gel synthesis or freeze-drying,this approach for fabricating SiO_(2)-CPM is simpler and cost-effective and allows the direct utilization of coal cinder post-combustion.
基金Wuxi University Research Start-up Fund for Introduced Talents(Grant No:2024r031)Technology Development Contract(Contract Registration Number:2024320205000963)+1 种基金National Natural Science Foundation of China(Grant No.52275288)Ningbo Key Research and Development Plan(Grant No.2023Z022).
文摘To solve the problem of abnormal abrasion of Cu-Based Friction Materials(CBFMs),Bionic Non-Smooth Surface(BNS)on friction surface of CBFMs was constructed based on bionic principles,and the optimal bionic prototype was selected by Finite Element Method(FEM).In addition,the bionic parameters were optimized by Response Surface Method(RSM).Samples holding BNS were prepared by Laser Processing,tribological properties were tested by a Friction and Wear Tester and worn surface morphology was characterized by a Scanning Electron Microscope(SEM).The results showed that BNS on friction surface could regulate the stress distribution and alleviate the peak stress.Among all samples,the coupled texture of pit-hexagonal got the minimum peak stress.During braking,bionic texture could also collect wear debris or change the motion forms from sliding to rotation,which can reduce abnormal abrasion.The wear rate was reduced by 19.31%.The results in this paper can provide a new idea for enhancing the tribological properties of CBFMs,and can also lay the foundation for further research of bionic tribology.
基金supported by the Indian Institute of Technology Delhi (IIT Delhi)
文摘Though the formation of polysulfide is desirable,as it contributes to the capacity build-up,it must not leak into the electrolyte.The loss of polysulfide causes capacity fade,a change in the local chemistry of the electrolyte,and anode poisoning.Constant efforts are in progress to find suitable polysulfide-absorbing materials;however,the magical polysulfide absorber is yet to be discovered or developed.Experimental methods alone often fall short in accelerating the investigations may be due to the complex Nature of the testing.This review focuses on the importance of computational methods,particularly density functional theory(DFT),in screening suitable polysulfide absorbers.It highlights the critical role of anchoring materials in improving Na-S battery performance,including pristine and doped graphene,metal–organic frameworks,carbon Nanofibers,vanadium disulfide,MXenes,and metal sulfides.By examining adsorption energies,charge transfer mechanisms,and catalytic properties,this review provides insights into the design of advanced materials that can effectively immobilize polysulfides and enhance battery stability.The review aims to guide future research efforts toward the development of high-performance RT Na-S batteries through a comprehensive understanding of the polysulfide-absorbing materials.
基金supported by the National Natural Science Foundation of China(No.52242305).
文摘Cement stands as a dominant contributor to global energy consumption and carbon emissions in the construction industry.With the upgrading of infrastructure and the improvement of building standards,traditional cement fails to reconcile ecological responsibility with advanced functional performance.By incorporating tailored fillers into cement matrices,the resulting composites achieve enhanced thermoelectric(TE)conversion capabilities.These materials can harness solar radiation from building envelopes and recover waste heat from indoor thermal gradients,facilitating bidirectional energy conversion.This review offers a comprehensive and timely overview of cementbased thermoelectric materials(CTEMs),integrating material design,device fabrication,and diverse applications into a holistic perspective.It summarizes recent advancements in TE performance enhancement,encompassing fillers optimization and matrices innovation.Additionally,the review consolidates fabrication strategies and performance evaluations of cement-based thermoelectric devices(CTEDs),providing detailed discussions on their roles in monitoring and protection,energy harvesting,and smart building.We also address sustainability,durability,and lifecycle considerations of CTEMs,which are essential for real-world deployment.Finally,we outline future research directions in materials design,device engineering,and scalable manufacturing to foster the practical application of CTEMs in sustainable and intelligent infrastructure.
基金financially supported by the National Natural Science Foundation of China(No.52303209)the“Lingyan”Program of Zhejiang Province(No.2024C03076)+1 种基金Zhejiang University K.P.Chao’s High Technology Development Foundationthe generous support provided by the joint research fund from the Shaoxing Institute of Zhejiang University and Shaoxing Maternity and Child Health Care Hospital。
文摘Responsive colorimetric materials exhibit significant potential for application in fields such as smart food packaging and wound monitoring.The functional integration of pH-indicators with material carriers enables breakthrough applications in nontraditional domains.In this study,we developed a novel material covalently grafted with a pH indicator that exhibited naked-eye pH-responsive color shifts.The covalent grafting of pH-responsive bromothymol blue onto carboxymethyl cellulose(CMC)was confirmed using advanced characterization techniques,including Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy.The pH-sensitive chromophore was covalently immobilized onto the CMC matrix through esterification,thereby establishing firm chemical conjugation.Moreover,a superior color-changing performance was achieved within several minutes in response to different pH values.The reusability and stability of this material offer distinct advantages over single-use pH test strips.pH-responsive colorimetric materials hold promise for efficient,noninvasive monitoring in intelligent packaging(food freshness),medical diagnostics(wound status,infections),biosensing,and environmental applications.
文摘A soft X-ray energy materials research beamline(BL20U2),a branch of energy materials beamline(E-line),has been constructed in the Shanghai Synchrotron Radiation Facility(SSRF)Phase-II project.It is now operational for soft X-ray resonant emission spectroscopy(RXES)and soft X-ray resonant elastic scattering(REXS)investigations.Optical optimization was implemented for high performance,e.g.,photon flux,energy-resolving power,and focus spot size.RXES experiments show that the energy range extends from 150 to 1500 eV.The elastic peak measured near titanium absorption edge(@445 eV)indicates an energy resolution of the RXES spectrometer of 65 meV.The measured photon flux is 3×10^(12)photons/s at 244 eV at the RXES sample position for an SSRF electron energy of 3.5 GeV and a projected ring current as 300 mA.The spot size at the RXES sample position is 23μm in the horizontal direction and 7.9μm in the vertical direction,respectively.Moreover,the angular resolution of elastic REXS scatterometer reaches 0.005°through measurement of X-ray reflection from the single-crystal silicon wafers.A sample of the REXS scatterometer is vibrationally decoupled from its chamber and cooled using copper braids connected from an open cycle liquid helium cryo reservoir,whereas the minimum sample temperature is below 15 K.
基金by the Industry–Academia Cooperation Project No.113A00262(Te-Hua Fang).URLs to the sponsor websites are available at:https://www.nstc.gov.tw.
文摘The mechanical performance of exceedingly soft materials such as Ag is significantly influenced by various working conditions.Therefore,this study systematically investigates the effects of crack geometry,substrate crystal orientation,and indenter shape on crack propagation.The mechanical response of Ag is analyzed using the quasi-continuum(QC)method.A pre-crack with a predefined depth and angle was introduced to initiate fracture behavior.The results show that when the pre-crack height is 50 A,the crack propagates rapidly as the imprint depth increases from0 to 7 A,grows steadily up to 15 A,and then accelerates sharply between 15 and 20 A.For other pre-crack heights,crack propagation occurs at a relatively faster rate.Substrates with[100],[010],and[001]crystal orientations promote crack extension,while the onset of plastic deformation(referred to as the yield point in this study)and the fracture strength both increase with increasing pre-crack height.The yield point,fracture strength,and stress intensity factors are highly sensitive to the pre-crack height.When the pre-crack angle is 90○,the fracture strength reaches its maximum of 0.2%higher than that of the uncracked sample-whereas at 0○,it reaches its minimum,still 53.8%higher than that of the uncracked sample.The sample model is conducted using AutoCAD software.The optimized quasicontinuum(QC)method is used to investigate the effects of different crack geometries,substrate crystal orientations,and indenter shapes on the crack extension of Ag material.Baskes and Dow(FBD)potential is borrowed to describe the interaction forces between Ag-Ag,Ni-Ag,and Ni-Ni.
基金Project supported by the National Natural Science Foundation of China(No.12472077)the supports from Shanghai Gaofeng Project for University Academic Program Development,Fundamental Research Funds for the Central Universities(No.22120240353).
文摘Lattice materials have demonstrated promising potential in engineering applications owing to their exceptional lightweight,high specific strength,and tunable mechanical properties.However,the traditional homogenization methods based on the classical elasticity theory struggle to accurately describe the non-classical mechanical behaviors of lattice materials,especially when dealing with complex unit-cell geometries featured by non-symmetric configurations or non-single central node connections.In response to this limitation,this study establishes a generalized homogenization model based on the micropolar theory framework,employing Hill's boundary conditions to precisely predict the equivalent moduli of complex lattice materials.By introducing the independent rotational degree of freedom(DOF)characteristic of the micropolar theory,the proposed model successfully overcomes the limitation of conventional methods in accurately describing the asymmetric deformation and scale effects.We initially calculate the constitutive relations of two-dimensional(2D)cross-shaped multi-node chiral lattices and subsequently extend the method to three-dimensional(3D)lattices,successfully predicting the mechanical properties of both traditional and eccentric body-centered cubic(BCC)lattices.The theoretical model is validated through the finite element numerical verification which shows excellent consistency with the theoretical predictions.A further parametric study investigates the influence of geometric parameters,revealing the underlying size-effect mechanism.This paper provides a reliable theoretical tool for the design and property optimization of complex lattice materials.
基金Natural Science Foundation of Beijing Municipality under Grant L243004the National Natural Science Foundation of China under Grant 62403060.
文摘Protective hardware is essential for mitigating damage caused by unavoidable falls in humanoid robots.Despite notable progress in fall protection hardware,the theoretical foundation for modeling and the feasibility of conducting full-scale fall experiments on robots or their surrogates remain somewhat limited.This paper proposes a method for optimizing the thickness of Expandable Polyethylene(EPE),which is used as back protection for the Chubao humanoid robot,based on small-scale impact test data to predict full-scale behavior.The optimal thickness is defined as a balance between compact design and protective effectiveness.An equivalent impact model characterized by four parameters:contact area S,mass m,fall height h,and cushioning material thickness d is introduced to describe impact conditions.The relationship between the peak impact acceleration ap and material thickness d,which forms the core of the method and gives rise to the name AP-D,is analyzed through their plotted curves.After introducing three characteristic parameters and two correction fac-tors,the relationship among the aforementioned variables is derived.Subsequently,both the optimal thickness do and its corresponding peak impact acceleration aop are predicted via nonlinear and linear regression models.Finally,the accuracy and effectiveness of the theoretically derived optimal thickness are validated on both a dummy and the actual robot.With the cushioning material applied,the peak chest acceleration is reduced to 41.57g for the dummy and 32.08g for the robot.
基金Project supported by the National Natural Science Foundation of China(Grant Nos.U25A20232,52325208,52173217,52202128)the Interdisciplinary Research Project for Young Teachers of USTB(Grant No.FRF-IDRY24-002)。
文摘As electronic technology continues to evolve towards miniaturization and integration,the demand for micro-refrigeration technology in microelectronic systems is increasing.Ferroelectric(FE)refrigeration technology based on the electrocaloric effect(ECE)has emerged as a highly promising candidate in this field,due to its advantages of high energy efficiency,simple structure,easy miniaturization,low cost,and environmental friendliness.The EC performance of FE materials essentially depends on the phase transition features under the coupled electric and thermal fields,making the E–T phase diagram a core tool for decoding the underlying mechanism of ECE.This paper reviews the development of EC materials,focusing on the comprehensive study of E–T phase diagrams.By correlating the microscopic phase structure of FE materials with the macroscopic physical properties,it clarifies the manipulation mechanism for enhanced ECE performance,providing theoretical support for the targeted design of high-performance EC materials.In the future,the introduction of data-driven methods is expected to enable the high-throughput construction of FE phase diagrams,thereby accelerating the optimization of high-performance EC materials and promoting the practical application of FE refrigeration technology.
