This research is focused on the calculation of a reasonable detonator delay time for realizing cut blast vibration control.First,the viscoelastic rock mass parameters corresponding to the engineering rock mass quality...This research is focused on the calculation of a reasonable detonator delay time for realizing cut blast vibration control.First,the viscoelastic rock mass parameters corresponding to the engineering rock mass quality classification were determined based on wave theory of Kelvin medium.Then,a calculation model was obtained for the millisecond-delay cut blast vibration in Kelvin media using the Starfield charge superposition principle.Further,the influence of the delay time on the cut blast vibration was quantitatively analyzed and a method for calculating the reasonable cut blasting millisecond delay time is proposed according to the principle of dimensional analysis.Finally,field tests were used to verify the applicability of the method.The results show that 5 ms to 20 ms is a better detonator delay time range and cut blasting vibration can be effectively controlled using the delay time calculated by the calculation model described in this paper.展开更多
Efficient hard-rock fragmentation remains a critical challenge in mechanized mining.This study designed an adjustable-spacing mold and conducted double cutting pick indentation tests on granite.Mechanical responses an...Efficient hard-rock fragmentation remains a critical challenge in mechanized mining.This study designed an adjustable-spacing mold and conducted double cutting pick indentation tests on granite.Mechanical responses and fragmentation characteristics under varying horizontal stresses,pick spacings,and groove depths were systematically analyzed.Unidirectional stress concentration altered the rock fragmentation modes,exhibiting a dual effect on the fragmentation process.The maximum indentation force(F_(max)),indentation hardness index(IHI),indentation modulus(IM),and indentation energy(W)initially increased and then decreased with rising horizontal stress.Appropriate spacing promoted radial crack coalescence,whereas too small a spacing(20 mm)caused repetitive re-fragmentation of rock chips,and too large a spacing(50 mm)resulted in unbroken ridges.Pre-cut grooves weakened the rock,reducing F_(max) and specific energy(SE),thus improving fragmentation efficiency,although the improvement slowed beyond a 10-mm groove depth.Based on the results and rock-mass conditioning assisted fragmentation mechanism,a“stress-structure dual control”assisted fragmentation mechanism was proposed,and a“pre-drilling unloading−alternate stopping”mining scheme was exploratorily designed.This approach creates favorable conditions for rock fragmentation by reducing stress levels and rock mass integrity in target zones,providing theoretical support and an engineering paradigm for mecheanized mining of deep resources.展开更多
Academic journals,consulting firms,and mainstream media have often published“predictions”about the future develop-ment of medical and health care.These publications often emphasize the potential of cutting-edge scie...Academic journals,consulting firms,and mainstream media have often published“predictions”about the future develop-ment of medical and health care.These publications often emphasize the potential of cutting-edge scientific or technical breakthroughs.Health Care Science looks at the problem from another perspective.We focus on how these changes enter the health system,how they operate in the real world,and how they reshape the organization and governance of medical services.At the beginning of 2026,we envision the following three major shifts that will reshape healthcare.展开更多
On January 19,2026,China's first structural interest rate cut of the year took effect.The People's Bank of China announced a 0.25 percentage point reduction in relending and rediscount rates,targeting key sect...On January 19,2026,China's first structural interest rate cut of the year took effect.The People's Bank of China announced a 0.25 percentage point reduction in relending and rediscount rates,targeting key sectors like small and micro enterprises(SMEs),technological innovation,and green transition.For the textile industry,where small and medium-sized enterprises account for over 90%of traditional manufacturing,the policy benefits will inject strong momentum into the high-quality development from multiple dimensions,including reduced financing costs,support for transformation funds,and expansion of foreign trade markets.展开更多
The principle and the constitution of an intelligent system for on-line and real-time montitoring tool cutting state were discussed and a synthetic sensors schedule combined a new type fluid acoustic emission sens...The principle and the constitution of an intelligent system for on-line and real-time montitoring tool cutting state were discussed and a synthetic sensors schedule combined a new type fluid acoustic emission sensor (AE) with motor current sensor was presented. The parallel communication between control system of machine tools, the monitoring intelligent system,and several decision-making systems for identifying tool cutting state was established It can auto - matically select the sensor way ,monitoring mode and identifying method in machining process- ing so as to build a successful and effective intelligent system for on -line and real-time moni- toring cutting tool states in FMS.展开更多
A mathematical model of the computer numerical control (CNC) heavy cuttingservo system including chatter in cutting courses was constructed for the chatter in CNC heavycutting. The theoretical analysis, computer simul...A mathematical model of the computer numerical control (CNC) heavy cuttingservo system including chatter in cutting courses was constructed for the chatter in CNC heavycutting. The theoretical analysis, computer simulation and orthogonal tests on this model show thatincreasing the gain of position K_(pp) can improve the rapid tracking performance of machine tools,and decreasing the delay time of speed loop τ_s can quickly eliminate the static error in thesystem, but the limited cutting width b_(lim) will descend correspondingly; excessively large orexcessively small gain of speed loop K_(ps) can result in decreasing b_(lim); optimizing K_(pp),τ_s and K_(ps) can improve the dynamic and static performance of the system and increase b_(lim).It is easy and feasible to optimize the servo parameters by the orthogonal test. This method caneffectively improve the system's stability and limited cutting width and it is suitable for the CNCheavy cutting of heavy-duty machine tools.展开更多
To investigate the characteristics of hydrate formation in oil–water systems, a high-pressure cell equipped with visual windows was used where a series of hydrate formation experiments were performed from natural gas...To investigate the characteristics of hydrate formation in oil–water systems, a high-pressure cell equipped with visual windows was used where a series of hydrate formation experiments were performed from natural gas + diesel oil + water systems at different water cuts and anti-agglomerant concentrations. According to the temperature and pressure profiles in test experiments, the processes of hydrate formation under two kinds of experimental procedures were analyzed first. Then, based on the experimental phenomena observed through the visual windows, the influences of water cut and anti-agglomerant on the places of hydrate formation and distribution, hydrate morphologies and hydrate morphological evolvements were investigated. Hydrate agglomeration, hydrate deposition and hydrate film growth on the wall were observed in experiments. Furthermore, three different mechanisms for hydrate film growth on the wall were identified. In addition, the influences of water cut and anti-agglomerant on the induction time of hydrate formation were also studied.展开更多
The drum shearer and high pressure water jet combined cutting system is an effective technology to cut hard coal-rock, but one problem of the technology is the choice of pick and nozzle location parameters. In order t...The drum shearer and high pressure water jet combined cutting system is an effective technology to cut hard coal-rock, but one problem of the technology is the choice of pick and nozzle location parameters. In order to solve the problem, the process and mechanism of combined cutting arc studied and mining seepage catastrophe theory is used to construct the mathematic and physical model of combined cutting hard coal-rock. Based on the model and detailed analysis of combined cutting mechanism, the single pick and nozzle combined cutting test-bed is built to test the main pick and nozzle location parameters of drum shearer and water jet combined cutting system. Test results show that the best vertical distance between the pick-tip and nozzle center point is the sum of cutting thickness and proper target distance in the Y axial direction; the best horizontal distance is the length between pick-tip point and coal-rock surface bursting crack point in the X axial direction. The best incident angle of water jet should be the same as the bursting crack line＇s angle in theory, but considering other important factors comprehensively, it is more reasonable when the incident angle of water jet is 90°.展开更多
For the designing of cutting-dies is a complex and experience-based process,it is poorly supported by conventional 3D CAD software.Thus,the majority of design activities,including the(re)modeling of those cutting die-...For the designing of cutting-dies is a complex and experience-based process,it is poorly supported by conventional 3D CAD software.Thus,the majority of design activities,including the(re)modeling of those cutting die-components that are directly responsible for performing shaping operations on a sheet-metal stamping part,traditionally still need to be carried-out repetitively,separately,and manually by the designer.To eliminate some of these drawbacks and upgrade the capabilities of conventional 3D CAD software,this paper proposes a new methodology for the development of a parametric system capable of automatically performing a(re)modeling process of compound washer dies' cutting-components.The presented methodology integrates CATIA V5 built-in modules,including Part Design,Assembly Design and Knowledge Advisor,publication mechanism,and compound cutting die-design knowledge.The system developed by this methodology represents an 'intelligent' assembly template composed of two modules GAJA1 and GAJA2,respectively.GAJA1 is responsible for the direct input of the die-design problem regarding the shape,dimensions and material of the stamping part,its extraction in the form of geometric features,and the transferring of relevant design parameters and features to the module GAJA2.GAJA2 interprets the current values for the input parameters and automatically performs the modeling process of cutting die-components,using die-design knowledge and the company's internal design and manufacturing standards.Experimental results show that this system significantly shortens the modeling-time for cutting the die-components,improves the modeling-quality,and enables the training of inexperienced designers.展开更多
Diameter frequency distribution in a specific stand provides basic information for forest resources management. In this study, four probability models were applied to analyze diameter distribution of natural forests a...Diameter frequency distribution in a specific stand provides basic information for forest resources management. In this study, four probability models were applied to analyze diameter distribution of natural forests after selective cutting with different intensities （low intensity of 13.0% in volume, medium intensity of 29.1%, high intensity of 45.8%, and extra-high intensity of 67.1%） The results show that the skewness and kurtosis of the four models are positive except that of low intensity selective cutting, which suggest that the number of small-size trees dominate the stand. The more intensity of selective cutting, the wider range of diameter distributions. The diameter structure of selective cutting with low intensity met Weibull and Beta distributions; that of medium intensity met Weibull, negative exponential as well as Gamma distributions; that of high intensity cutting met Weibull and negative exponential distributions, but that of extra-high intensity could not meet any above model. Weibull distribution model fits better than others regarding the structure of diameter distribution in natural forests managed on polycyclic cutting system. The results will provide basic information for sustainable management for mixed natural stands managed on a polycyclic cutting system.展开更多
A study was carried out to evaluate the effect of shelterwood cutting methods on stand structure and regeneration density. Data were collected from a northern hardwood forest stands in Iran with Fagus orientalis Lipsk...A study was carried out to evaluate the effect of shelterwood cutting methods on stand structure and regeneration density. Data were collected from a northern hardwood forest stands in Iran with Fagus orientalis Lipsky as dominant species, with/without shelterwood cutting operation. Results clearly demonstrate that the management of Fagus orientalis Lipsky with shelterwood cutting system affected the frequency and diversity of the understory herbaceous species. The frequency of Viola silvestris Lam., Asperula odorata L., Carex spp. and Rubus hyr-canus Juz increased significantly after shelterwood cutting. The DBH （diameter at breast height） of commercial species in control stands （57.50±2.15 cm） was greater than that in treated stands （50.67±1.88 cm）, whereas the total height of trees was similar between treated and control plots （21±0.5 m）. The number of Parrotia persica seedlings increased by 13.2% from 1995 to 2005 whereas the number of Fagus orientalis and Carpinus betulus seedlings significantly decreased from 1995 to 2005. In conclusion, it confirms that instead of shelterwood cutting method other silvicultural practices such as selection cutting method should be applied for the mountainous beech stands of Hyrcanian forests.展开更多
The accurate performance evaluation of a cutterhead is essential to improving cutterhead structure design and predicting project cost. Through extensive research, this paper evaluates the performance of a tunnel borin...The accurate performance evaluation of a cutterhead is essential to improving cutterhead structure design and predicting project cost. Through extensive research, this paper evaluates the performance of a tunnel boring machine(TBM) cutterhead for cutting ability and slagging ability. This paper propose cutting efficiency, stability, and continuity of slagging as the evaluation indexes of comprehensive cutterhead performance. On the basis of research of true TBM engineering applications, this paper proposes a calculation method for each index. A slagging efficiency index with a ratio of the maximum di erence between the slagging amount and average slagging is established. And a slagging stability index with a ratio of the maximum slagging fluctuation and average slagging is presented. Meanwhile, a cutting efficiency index by the weighed average value of multistage rock fragmentation of a cutter’s specific energy is established. The Robbins and China Railway Construction Corporation(CRCC) cutterheads are evaluated. The results show that under the same thrust and torque, the slagging stability of the CRCC scheme is worse, but the slagging continuity of the CRCC scheme is better. The cutting ability index shows that the CRCC cutterhead is more efficient.展开更多
Different types of plantations were observed in Baishilazi National Nature Reserve, Liaoning Province, for 34 a. The environmental quality ofAbies holophylla plantations was analyzed under different cutting systems. A...Different types of plantations were observed in Baishilazi National Nature Reserve, Liaoning Province, for 34 a. The environmental quality ofAbies holophylla plantations was analyzed under different cutting systems. Analysis factors included soil erosion rate, humification degree of litters, and water hold capacity. The surface soil loss of clear cutting area was 19000t·km?2·a?1 more than that of selective cutting area. The content of soil organic matter in board-leaved—Abies holophylla forest was 4.62% more than that in pure stand, and the water hold capacity of the mixed forest was 1.43 time of that of pure stand. The mixed forest of board-leaved—Abies holophylla by selective cutting can upgrade the ecological environment quality.展开更多
The purpose of this study is focused on development of an online monitoring system for measuring and evaluating the cutting condition as the ID-blade saw is cutting a silicon ingot. First,the cutting experiments are c...The purpose of this study is focused on development of an online monitoring system for measuring and evaluating the cutting condition as the ID-blade saw is cutting a silicon ingot. First,the cutting experiments are carried out and the cutting signals during the blade slicing a six-inch ingot are measured by a 3-axes load sensor which is mounted on the top of the ingot. To evaluate the blade condition in slicing,a novel data processing method,combining the discrete Fourier transform(DFT) with the discrete Wavelet transform(DWT),is proposed in this paper for extracting the components due to the rotation of the blade and the cutting impedance. To validate the effect of the method,four ID-blades with three different types of the blade edge are used and discussed. The obtained results show that the component induced from the rotation and the component due to the blade slicing can be extracted efficiently by introduction of the proposed method. Furthermore,a simple online monitoring system,which consists of a 3-axes load sensor or acceleration sensor,DC cuts high-pass filter,and AD converter embedded microcomputer,is designed. The estimated cutting condition information obtained from the proposed monitoring system can be used as a feedback signal to the slicing machine for production of high quality wafer.展开更多
The temperature distribution in the tool, chip and workpiece was studied during the orthogonal cuttingprocess Under several different cutting conditions. The temperature distribution is calculated by the finite differ...The temperature distribution in the tool, chip and workpiece was studied during the orthogonal cuttingprocess Under several different cutting conditions. The temperature distribution is calculated by the finite differencemethod. and the variation of the material properties with temperature was taken was taken into account The results obtained arecoincident with both previous published results and experimental measurements.展开更多
This Paper presents an automatic programming system developed for NC laser onning of Chinese charaCterswhich combines AutoCAD with NC Under Windows environment, and generates numerical controlled Programs by extractin...This Paper presents an automatic programming system developed for NC laser onning of Chinese charaCterswhich combines AutoCAD with NC Under Windows environment, and generates numerical controlled Programs by extracting outline (stroke) figures of Chinese Characters from outline character base, optimizing cutting routes, transferring them to AutoCAD for editing operations, such as rotation transfer, enlarging an mirroring, the system can transferto a laser cutting machine througy RS-232 series interface to accomplish laser cutting of large Chinese characters.展开更多
The paper introduces a new type of cutting system: the Offline Program Profile Lining and Cutting Robot System (OPPLCRS). The system adopts the offline program technology without teaching. The system can measure and c...The paper introduces a new type of cutting system: the Offline Program Profile Lining and Cutting Robot System (OPPLCRS). The system adopts the offline program technology without teaching. The system can measure and compensate every profile’s deformation automatically, so it is suit to process any batch of profiles, and the order of processing different profiles can be arranged at will. The OPPLCRS, firstly appearing in China, will have wide application in profile cutting fields.展开更多
The technique of cutting slabstone with stone-sawi ng machine is analyzed completely. A new kind of cutting movement trajectory is gi ven whose actual cutting efficiency is near to 100%. It can reduce the energy w ear...The technique of cutting slabstone with stone-sawi ng machine is analyzed completely. A new kind of cutting movement trajectory is gi ven whose actual cutting efficiency is near to 100%. It can reduce the energy w earing greatly, and the surface quality of the product is improved to the utmost extent. The design mechanism of the optimal cutting movement trajectory system structure is analyzed incisively. At the same time, the principle of the complex movement of horizontal movement and swing is researched. The optimal design scheme of th e cutting movement trajectory system structure is set up. The choice method to g et the superior value of the movement system structure is found. The mathematics function formula is established which exhibits the relationship between the par ameter of the complex movement structure and that of the system movement structu re. By the formula, the precision value of the offset can be figured out. The r ule is adapted to different types of energy-saving stone-sawing machines. The complex movement structure of horizontal movement and swing is designed to f ulfill the cutting movement. It can make the saw frame move up with the hanging pod deviating from the vertical direction. At the same time, the saw frame have a down-movement. Then the sum of the two movements is near to zero, and the saw blade and the stone can keep in touch during the whole horizontal cutting. The result is that the actual cutting efficiency is 100%. Also, when the hanging pod moves to the limited position, the saw frame can keep the original inertia, and continue to swing up. It makes the back-cutting have high energy-storing. The optimal design of the eccentricity balance wheel is done. The mathematics fo rmula for expressing the movement system structure is deduced. The calculation m ethod and formula is set up which is used to get the value of important componen ts such as offset. The choice method and formula of elasticity distortion coeffi cient is set up when the saw frame moves smoothly. It is concluded that the offs et is the key dimension to actualize the optimal cutting movement trajectory. The resolving of the technical problems discussed above offers a theoretic and technical basis for optimal design of energy-saving stone-sawing machines.展开更多
The remarkable ability of titanium alloys to preserve their superior physical and chemical characteristics when subjected to extreme conditions significantly enhances their importance in the aerospace,military,and med...The remarkable ability of titanium alloys to preserve their superior physical and chemical characteristics when subjected to extreme conditions significantly enhances their importance in the aerospace,military,and medical sectors.However,conventional machining of titanium alloys leads to elevated tool wear,development of surface defects,and reduced machining efficiency due to their low heat conductivity,and chemical affinity.These issues can be somewhat counteracted by integrating ultrasonic vibration in the conventional machining of titanium alloys and also enhance sustainability.This review article offers a holistic evaluation of the influence of ultrasonic vibration-assisted milling and turning on cutting forces,temperature,tool wear,and surface integrity,encompassing surface morphology,surface roughness,surface residual stress,surface hardness,and surface tribological properties during titanium alloys machining.Furthermore,it investigates the sustainability aspect that has not been previously examined.Studies on the performance of ultrasonic-assisted cutting revealed several advantages,including decreased cutting forces and cutting temperature,improved tool life,and a better-machined surface during machining.Consequently,the sustainability factor is improved due to minimized energy consumption and residual waste.In conclusion,the key challenges and future prospects in the ultrasonic-assisted cutting of titanium alloys are also discussed.This review article provides beneficial knowledge for manufactur-ers and researchers regarding ultrasonic vibration-assisted cutting of titanium alloy and will play an important role in achieving sustainability in the industry.展开更多
基金National Natural Science Foundation of China under Grant Nos.51979205 and 51939008。
文摘This research is focused on the calculation of a reasonable detonator delay time for realizing cut blast vibration control.First,the viscoelastic rock mass parameters corresponding to the engineering rock mass quality classification were determined based on wave theory of Kelvin medium.Then,a calculation model was obtained for the millisecond-delay cut blast vibration in Kelvin media using the Starfield charge superposition principle.Further,the influence of the delay time on the cut blast vibration was quantitatively analyzed and a method for calculating the reasonable cut blasting millisecond delay time is proposed according to the principle of dimensional analysis.Finally,field tests were used to verify the applicability of the method.The results show that 5 ms to 20 ms is a better detonator delay time range and cut blasting vibration can be effectively controlled using the delay time calculated by the calculation model described in this paper.
基金National Major Science and Technology Project for Deep Earth Exploration(No.2025ZD1008301)National Natural Science Foundation of China(No.52374153)for the financial supportthe support of the China Scholarship Council.
文摘Efficient hard-rock fragmentation remains a critical challenge in mechanized mining.This study designed an adjustable-spacing mold and conducted double cutting pick indentation tests on granite.Mechanical responses and fragmentation characteristics under varying horizontal stresses,pick spacings,and groove depths were systematically analyzed.Unidirectional stress concentration altered the rock fragmentation modes,exhibiting a dual effect on the fragmentation process.The maximum indentation force(F_(max)),indentation hardness index(IHI),indentation modulus(IM),and indentation energy(W)initially increased and then decreased with rising horizontal stress.Appropriate spacing promoted radial crack coalescence,whereas too small a spacing(20 mm)caused repetitive re-fragmentation of rock chips,and too large a spacing(50 mm)resulted in unbroken ridges.Pre-cut grooves weakened the rock,reducing F_(max) and specific energy(SE),thus improving fragmentation efficiency,although the improvement slowed beyond a 10-mm groove depth.Based on the results and rock-mass conditioning assisted fragmentation mechanism,a“stress-structure dual control”assisted fragmentation mechanism was proposed,and a“pre-drilling unloading−alternate stopping”mining scheme was exploratorily designed.This approach creates favorable conditions for rock fragmentation by reducing stress levels and rock mass integrity in target zones,providing theoretical support and an engineering paradigm for mecheanized mining of deep resources.
文摘Academic journals,consulting firms,and mainstream media have often published“predictions”about the future develop-ment of medical and health care.These publications often emphasize the potential of cutting-edge scientific or technical breakthroughs.Health Care Science looks at the problem from another perspective.We focus on how these changes enter the health system,how they operate in the real world,and how they reshape the organization and governance of medical services.At the beginning of 2026,we envision the following three major shifts that will reshape healthcare.
文摘On January 19,2026,China's first structural interest rate cut of the year took effect.The People's Bank of China announced a 0.25 percentage point reduction in relending and rediscount rates,targeting key sectors like small and micro enterprises(SMEs),technological innovation,and green transition.For the textile industry,where small and medium-sized enterprises account for over 90%of traditional manufacturing,the policy benefits will inject strong momentum into the high-quality development from multiple dimensions,including reduced financing costs,support for transformation funds,and expansion of foreign trade markets.
文摘The principle and the constitution of an intelligent system for on-line and real-time montitoring tool cutting state were discussed and a synthetic sensors schedule combined a new type fluid acoustic emission sensor (AE) with motor current sensor was presented. The parallel communication between control system of machine tools, the monitoring intelligent system,and several decision-making systems for identifying tool cutting state was established It can auto - matically select the sensor way ,monitoring mode and identifying method in machining process- ing so as to build a successful and effective intelligent system for on -line and real-time moni- toring cutting tool states in FMS.
文摘A mathematical model of the computer numerical control (CNC) heavy cuttingservo system including chatter in cutting courses was constructed for the chatter in CNC heavycutting. The theoretical analysis, computer simulation and orthogonal tests on this model show thatincreasing the gain of position K_(pp) can improve the rapid tracking performance of machine tools,and decreasing the delay time of speed loop τ_s can quickly eliminate the static error in thesystem, but the limited cutting width b_(lim) will descend correspondingly; excessively large orexcessively small gain of speed loop K_(ps) can result in decreasing b_(lim); optimizing K_(pp),τ_s and K_(ps) can improve the dynamic and static performance of the system and increase b_(lim).It is easy and feasible to optimize the servo parameters by the orthogonal test. This method caneffectively improve the system's stability and limited cutting width and it is suitable for the CNCheavy cutting of heavy-duty machine tools.
基金supported by Shandong Provincial Natural Science Foundation, China (Grant No. ZR2017MEE057)the Fundamental Research Funds for the Central Universities (14CX02207A, 17CX05006, 17CX06017)the Graduate Innovation Project of China University of Petroleum (East China) (YCX2017062).
文摘To investigate the characteristics of hydrate formation in oil–water systems, a high-pressure cell equipped with visual windows was used where a series of hydrate formation experiments were performed from natural gas + diesel oil + water systems at different water cuts and anti-agglomerant concentrations. According to the temperature and pressure profiles in test experiments, the processes of hydrate formation under two kinds of experimental procedures were analyzed first. Then, based on the experimental phenomena observed through the visual windows, the influences of water cut and anti-agglomerant on the places of hydrate formation and distribution, hydrate morphologies and hydrate morphological evolvements were investigated. Hydrate agglomeration, hydrate deposition and hydrate film growth on the wall were observed in experiments. Furthermore, three different mechanisms for hydrate film growth on the wall were identified. In addition, the influences of water cut and anti-agglomerant on the induction time of hydrate formation were also studied.
基金Project(2012AA062104) supported by the National High Technology Research and Development Program of ChinaProject(201104583) supported by the Postdoctoral Special Funded Projects,China
文摘The drum shearer and high pressure water jet combined cutting system is an effective technology to cut hard coal-rock, but one problem of the technology is the choice of pick and nozzle location parameters. In order to solve the problem, the process and mechanism of combined cutting arc studied and mining seepage catastrophe theory is used to construct the mathematic and physical model of combined cutting hard coal-rock. Based on the model and detailed analysis of combined cutting mechanism, the single pick and nozzle combined cutting test-bed is built to test the main pick and nozzle location parameters of drum shearer and water jet combined cutting system. Test results show that the best vertical distance between the pick-tip and nozzle center point is the sum of cutting thickness and proper target distance in the Y axial direction; the best horizontal distance is the length between pick-tip point and coal-rock surface bursting crack point in the X axial direction. The best incident angle of water jet should be the same as the bursting crack line＇s angle in theory, but considering other important factors comprehensively, it is more reasonable when the incident angle of water jet is 90°.
基金Project supported by the European Social Fund,European Union
文摘For the designing of cutting-dies is a complex and experience-based process,it is poorly supported by conventional 3D CAD software.Thus,the majority of design activities,including the(re)modeling of those cutting die-components that are directly responsible for performing shaping operations on a sheet-metal stamping part,traditionally still need to be carried-out repetitively,separately,and manually by the designer.To eliminate some of these drawbacks and upgrade the capabilities of conventional 3D CAD software,this paper proposes a new methodology for the development of a parametric system capable of automatically performing a(re)modeling process of compound washer dies' cutting-components.The presented methodology integrates CATIA V5 built-in modules,including Part Design,Assembly Design and Knowledge Advisor,publication mechanism,and compound cutting die-design knowledge.The system developed by this methodology represents an 'intelligent' assembly template composed of two modules GAJA1 and GAJA2,respectively.GAJA1 is responsible for the direct input of the die-design problem regarding the shape,dimensions and material of the stamping part,its extraction in the form of geometric features,and the transferring of relevant design parameters and features to the module GAJA2.GAJA2 interprets the current values for the input parameters and automatically performs the modeling process of cutting die-components,using die-design knowledge and the company's internal design and manufacturing standards.Experimental results show that this system significantly shortens the modeling-time for cutting the die-components,improves the modeling-quality,and enables the training of inexperienced designers.
基金supported by the National Natural Sci-ence Foundation of China (Grant No. 30972359)the Natural Science Foundation of Fujian Provinceince (No. 2008J0327, 2009J01232)
文摘Diameter frequency distribution in a specific stand provides basic information for forest resources management. In this study, four probability models were applied to analyze diameter distribution of natural forests after selective cutting with different intensities （low intensity of 13.0% in volume, medium intensity of 29.1%, high intensity of 45.8%, and extra-high intensity of 67.1%） The results show that the skewness and kurtosis of the four models are positive except that of low intensity selective cutting, which suggest that the number of small-size trees dominate the stand. The more intensity of selective cutting, the wider range of diameter distributions. The diameter structure of selective cutting with low intensity met Weibull and Beta distributions; that of medium intensity met Weibull, negative exponential as well as Gamma distributions; that of high intensity cutting met Weibull and negative exponential distributions, but that of extra-high intensity could not meet any above model. Weibull distribution model fits better than others regarding the structure of diameter distribution in natural forests managed on polycyclic cutting system. The results will provide basic information for sustainable management for mixed natural stands managed on a polycyclic cutting system.
文摘A study was carried out to evaluate the effect of shelterwood cutting methods on stand structure and regeneration density. Data were collected from a northern hardwood forest stands in Iran with Fagus orientalis Lipsky as dominant species, with/without shelterwood cutting operation. Results clearly demonstrate that the management of Fagus orientalis Lipsky with shelterwood cutting system affected the frequency and diversity of the understory herbaceous species. The frequency of Viola silvestris Lam., Asperula odorata L., Carex spp. and Rubus hyr-canus Juz increased significantly after shelterwood cutting. The DBH （diameter at breast height） of commercial species in control stands （57.50±2.15 cm） was greater than that in treated stands （50.67±1.88 cm）, whereas the total height of trees was similar between treated and control plots （21±0.5 m）. The number of Parrotia persica seedlings increased by 13.2% from 1995 to 2005 whereas the number of Fagus orientalis and Carpinus betulus seedlings significantly decreased from 1995 to 2005. In conclusion, it confirms that instead of shelterwood cutting method other silvicultural practices such as selection cutting method should be applied for the mountainous beech stands of Hyrcanian forests.
基金Supported by National basic research program of China(973 Project,Grant No.2013CB035400)National Natural Science Foundation of China(Grant No.51375001)+1 种基金Major Projects of Liaoning Science and Technology Plan(Grant No.2015106016)Basic Research Project of Central University(Grant No.DUT16QY11)
文摘The accurate performance evaluation of a cutterhead is essential to improving cutterhead structure design and predicting project cost. Through extensive research, this paper evaluates the performance of a tunnel boring machine(TBM) cutterhead for cutting ability and slagging ability. This paper propose cutting efficiency, stability, and continuity of slagging as the evaluation indexes of comprehensive cutterhead performance. On the basis of research of true TBM engineering applications, this paper proposes a calculation method for each index. A slagging efficiency index with a ratio of the maximum di erence between the slagging amount and average slagging is established. And a slagging stability index with a ratio of the maximum slagging fluctuation and average slagging is presented. Meanwhile, a cutting efficiency index by the weighed average value of multistage rock fragmentation of a cutter’s specific energy is established. The Robbins and China Railway Construction Corporation(CRCC) cutterheads are evaluated. The results show that under the same thrust and torque, the slagging stability of the CRCC scheme is worse, but the slagging continuity of the CRCC scheme is better. The cutting ability index shows that the CRCC cutterhead is more efficient.
文摘Different types of plantations were observed in Baishilazi National Nature Reserve, Liaoning Province, for 34 a. The environmental quality ofAbies holophylla plantations was analyzed under different cutting systems. Analysis factors included soil erosion rate, humification degree of litters, and water hold capacity. The surface soil loss of clear cutting area was 19000t·km?2·a?1 more than that of selective cutting area. The content of soil organic matter in board-leaved—Abies holophylla forest was 4.62% more than that in pure stand, and the water hold capacity of the mixed forest was 1.43 time of that of pure stand. The mixed forest of board-leaved—Abies holophylla by selective cutting can upgrade the ecological environment quality.
文摘The purpose of this study is focused on development of an online monitoring system for measuring and evaluating the cutting condition as the ID-blade saw is cutting a silicon ingot. First,the cutting experiments are carried out and the cutting signals during the blade slicing a six-inch ingot are measured by a 3-axes load sensor which is mounted on the top of the ingot. To evaluate the blade condition in slicing,a novel data processing method,combining the discrete Fourier transform(DFT) with the discrete Wavelet transform(DWT),is proposed in this paper for extracting the components due to the rotation of the blade and the cutting impedance. To validate the effect of the method,four ID-blades with three different types of the blade edge are used and discussed. The obtained results show that the component induced from the rotation and the component due to the blade slicing can be extracted efficiently by introduction of the proposed method. Furthermore,a simple online monitoring system,which consists of a 3-axes load sensor or acceleration sensor,DC cuts high-pass filter,and AD converter embedded microcomputer,is designed. The estimated cutting condition information obtained from the proposed monitoring system can be used as a feedback signal to the slicing machine for production of high quality wafer.
文摘The temperature distribution in the tool, chip and workpiece was studied during the orthogonal cuttingprocess Under several different cutting conditions. The temperature distribution is calculated by the finite differencemethod. and the variation of the material properties with temperature was taken was taken into account The results obtained arecoincident with both previous published results and experimental measurements.
文摘This Paper presents an automatic programming system developed for NC laser onning of Chinese charaCterswhich combines AutoCAD with NC Under Windows environment, and generates numerical controlled Programs by extracting outline (stroke) figures of Chinese Characters from outline character base, optimizing cutting routes, transferring them to AutoCAD for editing operations, such as rotation transfer, enlarging an mirroring, the system can transferto a laser cutting machine througy RS-232 series interface to accomplish laser cutting of large Chinese characters.
文摘The paper introduces a new type of cutting system: the Offline Program Profile Lining and Cutting Robot System (OPPLCRS). The system adopts the offline program technology without teaching. The system can measure and compensate every profile’s deformation automatically, so it is suit to process any batch of profiles, and the order of processing different profiles can be arranged at will. The OPPLCRS, firstly appearing in China, will have wide application in profile cutting fields.
文摘The technique of cutting slabstone with stone-sawi ng machine is analyzed completely. A new kind of cutting movement trajectory is gi ven whose actual cutting efficiency is near to 100%. It can reduce the energy w earing greatly, and the surface quality of the product is improved to the utmost extent. The design mechanism of the optimal cutting movement trajectory system structure is analyzed incisively. At the same time, the principle of the complex movement of horizontal movement and swing is researched. The optimal design scheme of th e cutting movement trajectory system structure is set up. The choice method to g et the superior value of the movement system structure is found. The mathematics function formula is established which exhibits the relationship between the par ameter of the complex movement structure and that of the system movement structu re. By the formula, the precision value of the offset can be figured out. The r ule is adapted to different types of energy-saving stone-sawing machines. The complex movement structure of horizontal movement and swing is designed to f ulfill the cutting movement. It can make the saw frame move up with the hanging pod deviating from the vertical direction. At the same time, the saw frame have a down-movement. Then the sum of the two movements is near to zero, and the saw blade and the stone can keep in touch during the whole horizontal cutting. The result is that the actual cutting efficiency is 100%. Also, when the hanging pod moves to the limited position, the saw frame can keep the original inertia, and continue to swing up. It makes the back-cutting have high energy-storing. The optimal design of the eccentricity balance wheel is done. The mathematics fo rmula for expressing the movement system structure is deduced. The calculation m ethod and formula is set up which is used to get the value of important componen ts such as offset. The choice method and formula of elasticity distortion coeffi cient is set up when the saw frame moves smoothly. It is concluded that the offs et is the key dimension to actualize the optimal cutting movement trajectory. The resolving of the technical problems discussed above offers a theoretic and technical basis for optimal design of energy-saving stone-sawing machines.
基金financially supported by the National Natural Science Foundation of China(Nos.92160301,92060203,52175415 and 52205475)the Science Center for Gas Turbine Project(No.P2023-B-IV-003-001)+1 种基金the Natural Science Foundation of Jiangsu Province(No.BK20210295)the Huaqiao University Engineering Research Center of Brittle Materials Machining(MOE,2023IME-001)。
文摘The remarkable ability of titanium alloys to preserve their superior physical and chemical characteristics when subjected to extreme conditions significantly enhances their importance in the aerospace,military,and medical sectors.However,conventional machining of titanium alloys leads to elevated tool wear,development of surface defects,and reduced machining efficiency due to their low heat conductivity,and chemical affinity.These issues can be somewhat counteracted by integrating ultrasonic vibration in the conventional machining of titanium alloys and also enhance sustainability.This review article offers a holistic evaluation of the influence of ultrasonic vibration-assisted milling and turning on cutting forces,temperature,tool wear,and surface integrity,encompassing surface morphology,surface roughness,surface residual stress,surface hardness,and surface tribological properties during titanium alloys machining.Furthermore,it investigates the sustainability aspect that has not been previously examined.Studies on the performance of ultrasonic-assisted cutting revealed several advantages,including decreased cutting forces and cutting temperature,improved tool life,and a better-machined surface during machining.Consequently,the sustainability factor is improved due to minimized energy consumption and residual waste.In conclusion,the key challenges and future prospects in the ultrasonic-assisted cutting of titanium alloys are also discussed.This review article provides beneficial knowledge for manufactur-ers and researchers regarding ultrasonic vibration-assisted cutting of titanium alloy and will play an important role in achieving sustainability in the industry.
