Mg-4.0Zn alloy composite reinforced by NiO-coated CNTs （NiO@CNTs） was synthesized by combining ball-milling and a casting process. The yield strength （YS） and elongation to failure of the composite were dramatical...Mg-4.0Zn alloy composite reinforced by NiO-coated CNTs （NiO@CNTs） was synthesized by combining ball-milling and a casting process. The yield strength （YS） and elongation to failure of the composite were dramatically increased by 44.9% and 38.6%, respectively, compared to its alloy counterpart. The signifi- cantly eahanced mechanical properties of the as-synthesized composite are mainly ascribed to an improved interracial bond, grain refinement and good dispersion of CNTs in the matrix via. coating NiO on CNTs. It is shown that the NiO-nanolayer on the CNTs significantly enhances the interfacial bonding strength and effectively prevents the agglomeration of CNTs. NiO@CNTs are, therefore, expected to be a highly sustainable and dispersible reinforcement for magnesium matrix composites with superior performance.展开更多
Microstructural features including pore size distribution, cell walls and phase compositions of magnesium oxychloride cement foams（MOCF） with various MgO powders and water mixture ratios were studied. Their infl uen...Microstructural features including pore size distribution, cell walls and phase compositions of magnesium oxychloride cement foams（MOCF） with various MgO powders and water mixture ratios were studied. Their infl uences on compressive strength, water absorption and resistance of MOCF were also discussed in detail. The experimental results indicated that moderate and slight excess MgO powders（MgO/MgCl2 molar ratios from 5.1 to 7） were beneficial to the formation of excellent microstructure of MOCF, but increasing water contents（H2O/MgO mass ratios from 0.9 to 1.29） might result in opposite conclusions. The microstructure of MOCF produced with moderate and slight excess MgO powders could enhance the compressive strength, while serious excess MgO powders addition（MgO/MgCl2 molar ratios = 9） would destroy the cell wall structures, and therefore decrease the strength of the system. Although MOCF produced with excess MgO powders could decrease the water absorption, its softening coefficient was lower than that of the material produced with moderate MgO powders. This might be due to the instability of phase 5, the volume expansion and cracking of cell walls as immersed the sample into water.展开更多
In-situ growing carbon nanotubes （CNTs） directly on carbon fibers （CFs） always lead to a degraded tensile strength of CFs and then a poor fiber-dominated mechanical property of carbon/carbon composites （C/ Cs）. ...In-situ growing carbon nanotubes （CNTs） directly on carbon fibers （CFs） always lead to a degraded tensile strength of CFs and then a poor fiber-dominated mechanical property of carbon/carbon composites （C/ Cs）. To solve this issue, here, a novel carbon fiber-based multiscale reinforcement is reported. To synthesize it, carbon fibers （CFs） have been first grafted by graphene oxide （GO）, and then carbon nanotubes （CNTs） have been in-situ grown on GO-grafted CFs by catalytic chemical vapor deposition. Characterizations on this novel reinforcement show that GO grafting cannot only nondestructively improve the surface chemical activity of CFs but also protect CFs against the high-temperature corrosion of metal catalyst during CNT growth, which maintains their tensile properties. Tensile property tests for unidirectional C/Cs with different preforms show that this novel reinforcement can endow C/C with improved tensile properties, 32% and 87% higher than that of pure C/C and C/C only doped with in-situ grown CNTs. This work would open up a possibility to fabricate multiscale C/Cs with excellent global performance.展开更多
This work studied the preparation of starting powder mixture influenced by milling time and its effect on the particle morphology （especially the shape） and, consequently, density and compression properties of in si...This work studied the preparation of starting powder mixture influenced by milling time and its effect on the particle morphology （especially the shape） and, consequently, density and compression properties of in situ Ti-TiB composite materials produced by selective laser melting （SLM） technology. Starting powder composite system was prepared by mixing 95 wt% commercially pure titanium （CP-Ti） and 5 wt% titanium diboride （TiB2） powders and subsequently milled for two different times （i.e. 2 h and 4 h）. The milled powder mixtures after 2 h and 4 h show nearly spherical and irregular shape, respectively. Subsequently, the resultant Ti-5 wt% TiB2 powder mixtures were used for SLM processing. Scanning electron microscopy image of the SLM-processed Ti-TiB composite samples show needle-shape TiB phase distributed across the Ti matrix, which is the product of an in-situ chemical reaction between Ti and TiB2 during SLM. The Ti-TiB composite samples prepared from 2 h and 4 h milled Ti-TiB2 powders show different relative densities of 99.5% and 95.1%, respectively. Also, the compression properties such as ultimate strength and compression strain for the 99.5% dense composite samples is 1421 MPa and 17.8%, respectively, which are superior to those （883 MPa and 5.5%, respectively） for the 95.1% dense sample. The results indicate that once Ti and TiB2 powders are connected firmly to each other and powder mixture of nearly spherical shape is obtained, there is no additional benefit in increasing the milling time and, instead, it has a negative effect on the density （i.e. increasing porosity level） of the Ti-TiB composite materials and their mechanical properties.展开更多
The x wt%graphene-Ti composites（x = 0,0.2,0.3 and 0.4） were obtained using the powder metallurgy method.The X-ray diffraction results demonstrated that the peak intensity of graphene increased monotonically with inc...The x wt%graphene-Ti composites（x = 0,0.2,0.3 and 0.4） were obtained using the powder metallurgy method.The X-ray diffraction results demonstrated that the peak intensity of graphene increased monotonically with increasing graphene content.Furthermore,the number of grain boundary and interface between graphene and matrix increased as graphene increased,which led to a sharp rise of thermal resistances.The thermal conductivity and specific heat capacity of composites initially decreased drastically with addition of graphene,but then increased with increasing graphene content from 0.2 to 0.4 wt%.This phenomenon was connected with the graphene content and the characteristics of Ti matrix（pores,grain boundary and interface between graphene and matrix）.The variation of the compressive strength of composites was attributed to the interaction effects of the average grain size of the Ti matrix（d_m） and the volume fraction（V_f） and aspect ratio（A） of graphene.展开更多
Microstructure and mechanical behavior of high volume content SiCp/7xxxAl composites have not been explored yet. Therefore, in the present work, 45 vol.% SiCp/7075Al composite has been prepared by pres- sure infiltrat...Microstructure and mechanical behavior of high volume content SiCp/7xxxAl composites have not been explored yet. Therefore, in the present work, 45 vol.% SiCp/7075Al composite has been prepared by pres- sure infiltration method. High density dislocations were found around SiC/Al interface in SiCp/7075Al composite after water-quenching and aging treatment. Fine dispersed nano-η＇ phases were observed after the aging treatment. Adverse to other SiCp/Al composites prepared by the pressure infiltration method, an interface layer was observed between SiC particles and AI matrix. Furthermore, high-resolution trans- mission electron microscopy （HRTEM） observation indicated that this interface layer was coherent/semi- coherent with that of the SiC particles. 45 vol.% SiCp/7075Al composite demonstrated high tensile strength （630 MPa） and micro-ductility. Compared to aged SiCp/2024Al composite, the aged SiCp/7075Al com- posite showed an increase of about 200% in the tensile strain and 90% in the tensile strength, respectively. It is speculated that nano-η＇ phases in the Al matrix significantly contributed to the strengthening effect while the interface layer between SiC and AI matrix might be beneficial to the strength and plasticity of SiCp/7075Al composite.展开更多
FeAl/TiC composites were fabricated by hot pressing blended elemental powders. The effects of Ni-doping on thedensification and mechanical properties of the composites were studied. Results show that the density of th...FeAl/TiC composites were fabricated by hot pressing blended elemental powders. The effects of Ni-doping on thedensification and mechanical properties of the composites were studied. Results show that the density of the composites decreases with the content of TiC increasing, and the addition of Ni significantly improves the densificationprocess by enhancing mass transfer in the bonding phase. The mechanical properties of the composites are closelyrelated with their porosity. Besides increasing the density of the composites, the addition of Ni improves the mechanical properties by other three effects: solution-strengthening the bonding phase, strengthening the FeAI-TiC interfaceand increasing ductile fracture in FeAl phase.展开更多
Relatively well crystallized and high aspect ratio Mg-Al layered double hydroxides（LDHs） were prepared by coprecipitation process in aqueous solution and further rehydrated to an organic modified LDH（OLDH） in the ...Relatively well crystallized and high aspect ratio Mg-Al layered double hydroxides（LDHs） were prepared by coprecipitation process in aqueous solution and further rehydrated to an organic modified LDH（OLDH） in the presence of surfactant. The intercalated structure and high aspect ratio of OLDH were verified by X-ray diffraction（XRD） and scanning electron microscopy（SEM）. A series of poly（propylene carbonate）（PPC）/OLDH composite films with different contents of OLDH were prepared via a melt-blending method. Their cross section morphologies, gas barrier properties and tensile strength were investigated as a function of OLDH contents. SEM results show that OLDH platelets are well dispersed within the composites and oriented parallel to the composite sheet plane. The gas barrier properties and tensile strength are obviously enhanced upon the incorporation of OLDH. Particularly, PPC/2%OLDH film exhibits the best barrier properties among all the composite films. Compared with pure PPC, the oxygen permeability coefficient（OP） and water vapor permeability coefficient（WVP） is reduced by 54% and 17% respectively with 2% OLDH addition. Furthermore, the tensile strength of PPC/2%OLDH is 83% higher than that of pure PPC with only small lose of elongation at break. Therefore, PPC/OLDH composite films show great potential application in packaging materials due to its biodegradable properties, superior oxygen and moisture barrier characteristics.展开更多
The tensile properties of 22Cr–2Ni–4Mn–0.2N micro-duplex stainless steels with different Ni and Mn contents were investigated. Duplex stainless steels were vacuum induction melted and hot rolled, then annealed at 1...The tensile properties of 22Cr–2Ni–4Mn–0.2N micro-duplex stainless steels with different Ni and Mn contents were investigated. Duplex stainless steels were vacuum induction melted and hot rolled, then annealed at 1,000–1,100 °C, at which temperature both the austenite and ferrite phases were stable. The volume fraction of the ferrite phase was markedly affected by the alloying elements of Mn and Ni; 1 wt% of Mn was equivalent to 0.4 wt% of Ni. All of the steels tested at room temperature showed the common strain-hardening behavior, while the steels tested at lower temperatures（-30 or-50 °C）showed a distinct inflection point in their stress–strain curves, which resulted from the transformation of the austenite to straininduced martensite. The onset strain（e0） of the inflection point in the stress–strain curve depended on the Md30 value of the steel. Testing at lower temperatures resulted in smaller e0 and consequently higher strengths and fracture strains（ef）. The tensile behavior was examined from the perspective of austenite stability of the micro-duplex stainless steels with the different Ni and Mn contents.展开更多
Erratum to:International Journal of Minerals, Metallurgy and Materials Volume 26, Number 9, September 2019, Page 1151https://doi.org/10.1007/s12613-019-1854-1The original version of this article unfortunately containe...Erratum to:International Journal of Minerals, Metallurgy and Materials Volume 26, Number 9, September 2019, Page 1151https://doi.org/10.1007/s12613-019-1854-1The original version of this article unfortunately contained a mistake. The presentation of Fig. 11 was incorrect. The correct version is given below:展开更多
Alumina-(0 similar to 20 vol. pct) iron composites were fabricated by hot-pressing of well-mixed-alumina and iron powders at 1400 degreesC and 30 MPa for 30 min. Hot-pressed bodies with nearly theoretical density were...Alumina-(0 similar to 20 vol. pct) iron composites were fabricated by hot-pressing of well-mixed-alumina and iron powders at 1400 degreesC and 30 MPa for 30 min. Hot-pressed bodies with nearly theoretical density were obtained for addition up to 10 vol. pct Fe, but relative density decreased gradually with further increase in Fe addition. The materials exhibit a homogeneous dispersion of Fe. Fracture strength of the composites exhibits a maximum value of 604 MPa at 15 vol. pct Fe, which is 1.5 times that of alumina alone. Fracture toughness increases with the increase in Fe content, reaching 7.5 MPa.m(1/2) at 20 vol. pct Fe. The theoretical values of fracture toughness was calculated and compared with the experimental one. Toughening mechanisms of the composites are also discussed.展开更多
In spray atomization and codeposition, a molten stream of metal is disintegrated into a fine dispersion of droplets by high velocity gas jets. The resulting semi-solidified droplets are directed towards a substrate wh...In spray atomization and codeposition, a molten stream of metal is disintegrated into a fine dispersion of droplets by high velocity gas jets. The resulting semi-solidified droplets are directed towards a substrate where they impact and collect as rapidly solidified splats. Relatively high rates of solidification are achieved as a result of the thinness of the splats and the rapid heat extraction during flight and upon impacting with the substrate. The processing method uses codeposition of the metallic semi-solidified droplets (metallic matrix) with the injected reinforcement ceramic particles. In the present paper, the microstructures, mechanical properties, interfacial properties, thermal stability and aging behaviour of spray atomized and codeposited Al-Li-X MMC's (injected X=SiC, Al2O3) are reported and correlated to the processing conditions.展开更多
An effective procedure has been developed to synthesize the functionalized graphene oxide grafted by maleic anhydride grafted liquid polybutadiene（MLPB-GO）. Fourier transform spectroscopy and X-ray photoelectron spe...An effective procedure has been developed to synthesize the functionalized graphene oxide grafted by maleic anhydride grafted liquid polybutadiene（MLPB-GO）. Fourier transform spectroscopy and X-ray photoelectron spectroscopy indicate the successful functionalization of GO. The NR/MLPB-GO composites were then prepared by the co-coagulation process. The results show that the mechanical properties of NR/MLPB-GO composites are obviously superior to those of NR/GO composites and neat NR. Compared with neat NR, the tensile strength, modulus at 300% strain and tear strength of NR composite containing 2.12 phr MLPB-GO are significantly increased by 40.5%, 109.1% and 85.0%, respectively. Dynamic mechanical analysis results show that 84% increase in storage modulus and 2.9 K enhancement in the glass transition temperature of the composite have been achieved with the incorporation of 2.12 phr MLPB-GO into NR. The good dispersion of GO and the strong interface interaction in the composites are responsible for the unprecedented reinforcing efficiency of MLPB-GO towards NR.展开更多
The phase compositions and properties of Ti3SiC2-based composites with SiC addition of 5%-30% in mass fraction fabricated by in-situ reaction and hot pressing sintering were studied. SiC addition effectively prevented...The phase compositions and properties of Ti3SiC2-based composites with SiC addition of 5%-30% in mass fraction fabricated by in-situ reaction and hot pressing sintering were studied. SiC addition effectively prevented TiC synthesis but facilitated SiC synthesis. The Ti3SiC2/Ti C-SiC composite had better oxidation resistance when SiC added quantity reached 20% but poorer oxidation resistance with SiC addition under 15% than Ti3SiC2/TiC composite at higher temperatures. There were more than half of the original SiC and a few Ti3SiC2 remaining in Ti3SiC2/Ti C-SiC with 20% SiC addition, but all constituents in Ti3Si2/TiC composite were oxidized after 12 h in air at 1500 °C. The oxidation scale thickness of TS30, 1505.78 μm, was near a half of that of T,2715 μm, at 1500 °C for 20 h. Ti3SiC2/Ti C composite had a flexural strength of 474 MPa, which was surpassed by Ti3SiC2/TiC-SiC composites when SiC added amount reached 15%. The strength reached the peak of 518 MPa at 20% SiC added amount.展开更多
LaFeO3 was used to improve the hydrogen storage properties of Mg H2. The Mg H2＋20 wt.%La Fe O3 composite was prepared by ball milling method. The composite could absorb 3.417 wt.% of hydrogen within 21 min at 423 K w...LaFeO3 was used to improve the hydrogen storage properties of Mg H2. The Mg H2＋20 wt.%La Fe O3 composite was prepared by ball milling method. The composite could absorb 3.417 wt.% of hydrogen within 21 min at 423 K while Mg H2 only uptaked 0.977 wt.% hydrogen under the same conditions. The composite also released 3.894 wt.% of hydrogen at 623 K, which was almost twice more than Mg H2. The TPD measurement showed that the onset dissociation temperature of the composite was 570 K, 80 K lower than the Mg H2. Based on the Kissinger plot analysis of the composite, the activation energy E des was estimated to be 86.69 k J/mol, which was 36 k J/mol lower than Mg H2. The XRD and SEM results demonstrated that highly dispersed La Fe O3 could be presented in Mg H2, benefiting the reduction of particle size and also acting as an inhibitor to keep the particles from clustering during the ball-milled process.展开更多
This paper proposes a new analytical solution to predict the shear modulus of a two-dimensional（2D） plain weave fabric（PWF） composite accounting for the interaction of orthogonal interlacing strands with coupled s...This paper proposes a new analytical solution to predict the shear modulus of a two-dimensional（2D） plain weave fabric（PWF） composite accounting for the interaction of orthogonal interlacing strands with coupled shear deformation modes including not only relative bending but also torsion,etc.The two orthogonal yarns in a micromechanical unit cell are idealized as curved beams with a path depicted by using sinusoidal shape functions.The internal forces and macroscopic deformations carried by the yarn families,together with macroscopic shear modulus of PWFs are derived by means of a strain energy approach founded on micromechanics.Three sets of experimental data pertinent to three kinds of 2D orthogonal PWF composites have been implemented to validate the new model.The calculations from the new model are also compared with those by using two models in the earlier literature.It is shown that the experimental results correlate well with predictions from the new model.展开更多
Hoppressed Si3N4/SiC platelet composites had been investigated with respect to their microstructure and mechanical properties. The results indicate that Vickers hardness, elastic modulus and fracture toughness of the ...Hoppressed Si3N4/SiC platelet composites had been investigated with respect to their microstructure and mechanical properties. The results indicate that Vickers hardness, elastic modulus and fracture toughness of the composites were increased by the addition of SiC platelet until the content up to 20 vol pct. A slight decrease in flexural Strength was measured at room temperature with increasing SiC platelet content. The high temperature flexural strength tests at 1150, 1250, and 1350℃ were conducted. It was found that the flexural strength at elevated temperature was degraded with the rising temperature, and the downward trend of flexural strength for the composite containing 10 vol. pct SiC platelet was less. The results indicate that SiC platelet had a positive influence on the high temperature strength. Effects of SiC platelet reinforcement were presented展开更多
An equivalent continuum method only considering the stretching deformation of struts was used to study the in-plane stiffness and strength of planar lattice grid com- posite materials. The initial yield equations of l...An equivalent continuum method only considering the stretching deformation of struts was used to study the in-plane stiffness and strength of planar lattice grid com- posite materials. The initial yield equations of lattices were deduced. Initial yield surfaces were depicted separately in different 3D and 2D stress spaces. The failure envelope is a polyhedron in 3D spaces and a polygon in 2D spaces. Each plane or line of the failure envelope is corresponding to the yield or buckling of a typical bar row. For lattices with more than three bar rows, subsequent yield of the other bar row after initial yield made the lattice achieve greater limit strength. The importance of the buckling strength of the grids was strengthened while the grids were relative sparse. The integration model of the method was used to study the nonlinear mechanical properties of strain hardening grids. It was shown that the integration equation could accurately model the complete stress-strain curves of the grids within small deformations.展开更多
A facile ammonium-dichromate solution immersion method was introduced to synthesize the copperwettable Cr3C2 coating on and inside the carbon-carbon （C/C） preform. The formation mechanism and the microstructures of ...A facile ammonium-dichromate solution immersion method was introduced to synthesize the copperwettable Cr3C2 coating on and inside the carbon-carbon （C/C） preform. The formation mechanism and the microstructures of the Cr3C2 coatings were studied. The contact angle between molten copper and the C/C decreased from 140°to 60°, demonstrating the significant improvement in the wettability. The Cr3C2- coated C/C-Cu composite with only 4.2% porosity and 3.69 gcm^-3 density was manufactured through copper infiltration. As a result, the thermal and electrical conductivity of the modified C/C-Cu increased significantly due to the infiltrated copper. Also the mechanical properties of the composites including both the flexural and compressive strengths were enhanced by over 100%. The modified C/C-Cu composite exhibited lower friction coefficients and wear rates for different load levels than those of the commercial C/Cu composite. These results demonstrate the potential of the modified C/C-Cu material for use in electrical contacts.展开更多
Centrifugal casting was applied to produce cylindrical castings using SiCp/Al composite slurry,which contained 20%SiC particles.The castings comprised a particle free zone and a particle rich zone.The amount of SiC pa...Centrifugal casting was applied to produce cylindrical castings using SiCp/Al composite slurry,which contained 20%SiC particles.The castings comprised a particle free zone and a particle rich zone.The amount of SiC particles had a dramatic transformation from the particle rich zone to the particle free zone,and the maximum content of SiC particles in the particle rich zone reached up to 40 vol%.The ultimate tensile strength（UTS） of the as-cast SiCp / Al composites in the particle rich zone was 143 MPa,and the fracture was caused by the desorption of SiC particles from matrix alloy.The coefficient of thermal expansion（CTE） of the SiC_p / Al composites in the range of 20 and 100 ℃ was determined as 16.67×10^（-6） s^（-1）,and the experimental CTE was lower than the predicted data based on the Kerner＇s model.The results show that the decrease in CTE in the case of the composites at high temperature stage can be attributed to the solute concentration of Si in Al and the plastic deformation of the matrix alloy in the composites with void architecture.展开更多
基金supported by the National Key Research and Development Program(Nos.2016YFB0701201,2016YFB0701203)National Natural Science Foundation of China(Nos.51671101,51464034)+2 种基金Natural Science foundation of Jiangxi Province(No.20161ACB21003)Excellent Young Talent plan of Jiangxi Province(No.20162BCB23013)the Scientific Research Foundation of the Education Department of Jiangxi Province(Nos.GJJ151309,GJJ150010)
文摘Mg-4.0Zn alloy composite reinforced by NiO-coated CNTs （NiO@CNTs） was synthesized by combining ball-milling and a casting process. The yield strength （YS） and elongation to failure of the composite were dramatically increased by 44.9% and 38.6%, respectively, compared to its alloy counterpart. The signifi- cantly eahanced mechanical properties of the as-synthesized composite are mainly ascribed to an improved interracial bond, grain refinement and good dispersion of CNTs in the matrix via. coating NiO on CNTs. It is shown that the NiO-nanolayer on the CNTs significantly enhances the interfacial bonding strength and effectively prevents the agglomeration of CNTs. NiO@CNTs are, therefore, expected to be a highly sustainable and dispersible reinforcement for magnesium matrix composites with superior performance.
基金Funded by the National Natural Science Foundation of China(No.51478370)the EPSRC-NSFC Joint Research Projec(No.51461135005)
文摘Microstructural features including pore size distribution, cell walls and phase compositions of magnesium oxychloride cement foams（MOCF） with various MgO powders and water mixture ratios were studied. Their infl uences on compressive strength, water absorption and resistance of MOCF were also discussed in detail. The experimental results indicated that moderate and slight excess MgO powders（MgO/MgCl2 molar ratios from 5.1 to 7） were beneficial to the formation of excellent microstructure of MOCF, but increasing water contents（H2O/MgO mass ratios from 0.9 to 1.29） might result in opposite conclusions. The microstructure of MOCF produced with moderate and slight excess MgO powders could enhance the compressive strength, while serious excess MgO powders addition（MgO/MgCl2 molar ratios = 9） would destroy the cell wall structures, and therefore decrease the strength of the system. Although MOCF produced with excess MgO powders could decrease the water absorption, its softening coefficient was lower than that of the material produced with moderate MgO powders. This might be due to the instability of phase 5, the volume expansion and cracking of cell walls as immersed the sample into water.
基金supported by the National Natural Science Foundation of China (Nos.51432008,51502242,U1435202,and 51202194)the Research Fund for the Doctoral Program of Higher Education of China (No.20126102110013)the Key Grant Project of Chinese Ministry of Education (No.313047)
文摘In-situ growing carbon nanotubes （CNTs） directly on carbon fibers （CFs） always lead to a degraded tensile strength of CFs and then a poor fiber-dominated mechanical property of carbon/carbon composites （C/ Cs）. To solve this issue, here, a novel carbon fiber-based multiscale reinforcement is reported. To synthesize it, carbon fibers （CFs） have been first grafted by graphene oxide （GO）, and then carbon nanotubes （CNTs） have been in-situ grown on GO-grafted CFs by catalytic chemical vapor deposition. Characterizations on this novel reinforcement show that GO grafting cannot only nondestructively improve the surface chemical activity of CFs but also protect CFs against the high-temperature corrosion of metal catalyst during CNT growth, which maintains their tensile properties. Tensile property tests for unidirectional C/Cs with different preforms show that this novel reinforcement can endow C/C with improved tensile properties, 32% and 87% higher than that of pure C/C and C/C only doped with in-situ grown CNTs. This work would open up a possibility to fabricate multiscale C/Cs with excellent global performance.
基金supported by the Australian Research Council’s Projects Funding Scheme (No. DP110101653)the European Commission (BioTiNet-ITN G.A. No.264635)the Deutsche Forschungsgemeinschaft (SFB/Transregio 79, Project M1)
文摘This work studied the preparation of starting powder mixture influenced by milling time and its effect on the particle morphology （especially the shape） and, consequently, density and compression properties of in situ Ti-TiB composite materials produced by selective laser melting （SLM） technology. Starting powder composite system was prepared by mixing 95 wt% commercially pure titanium （CP-Ti） and 5 wt% titanium diboride （TiB2） powders and subsequently milled for two different times （i.e. 2 h and 4 h）. The milled powder mixtures after 2 h and 4 h show nearly spherical and irregular shape, respectively. Subsequently, the resultant Ti-5 wt% TiB2 powder mixtures were used for SLM processing. Scanning electron microscopy image of the SLM-processed Ti-TiB composite samples show needle-shape TiB phase distributed across the Ti matrix, which is the product of an in-situ chemical reaction between Ti and TiB2 during SLM. The Ti-TiB composite samples prepared from 2 h and 4 h milled Ti-TiB2 powders show different relative densities of 99.5% and 95.1%, respectively. Also, the compression properties such as ultimate strength and compression strain for the 99.5% dense composite samples is 1421 MPa and 17.8%, respectively, which are superior to those （883 MPa and 5.5%, respectively） for the 95.1% dense sample. The results indicate that once Ti and TiB2 powders are connected firmly to each other and powder mixture of nearly spherical shape is obtained, there is no additional benefit in increasing the milling time and, instead, it has a negative effect on the density （i.e. increasing porosity level） of the Ti-TiB composite materials and their mechanical properties.
基金supported by the Chinese Postdoctoral Science Foundation(No.2014M561795)the Postdoctoral Scientific Research Project of Zhejiang Province,China(No.BSH1401037)
文摘The x wt%graphene-Ti composites（x = 0,0.2,0.3 and 0.4） were obtained using the powder metallurgy method.The X-ray diffraction results demonstrated that the peak intensity of graphene increased monotonically with increasing graphene content.Furthermore,the number of grain boundary and interface between graphene and matrix increased as graphene increased,which led to a sharp rise of thermal resistances.The thermal conductivity and specific heat capacity of composites initially decreased drastically with addition of graphene,but then increased with increasing graphene content from 0.2 to 0.4 wt%.This phenomenon was connected with the graphene content and the characteristics of Ti matrix（pores,grain boundary and interface between graphene and matrix）.The variation of the compressive strength of composites was attributed to the interaction effects of the average grain size of the Ti matrix（d_m） and the volume fraction（V_f） and aspect ratio（A） of graphene.
基金the financial support of the project from "Key Laboratory Fund (5780011513) of Harbin Institute of Technology""University Basic Fund (5710011113) of Harbin Institute of Technology""the Fundamental Research Funds for the Central Universities" (Grant No. HIT. NSRIF. 20161)
文摘Microstructure and mechanical behavior of high volume content SiCp/7xxxAl composites have not been explored yet. Therefore, in the present work, 45 vol.% SiCp/7075Al composite has been prepared by pres- sure infiltration method. High density dislocations were found around SiC/Al interface in SiCp/7075Al composite after water-quenching and aging treatment. Fine dispersed nano-η＇ phases were observed after the aging treatment. Adverse to other SiCp/Al composites prepared by the pressure infiltration method, an interface layer was observed between SiC particles and AI matrix. Furthermore, high-resolution trans- mission electron microscopy （HRTEM） observation indicated that this interface layer was coherent/semi- coherent with that of the SiC particles. 45 vol.% SiCp/7075Al composite demonstrated high tensile strength （630 MPa） and micro-ductility. Compared to aged SiCp/2024Al composite, the aged SiCp/7075Al com- posite showed an increase of about 200% in the tensile strain and 90% in the tensile strength, respectively. It is speculated that nano-η＇ phases in the Al matrix significantly contributed to the strengthening effect while the interface layer between SiC and AI matrix might be beneficial to the strength and plasticity of SiCp/7075Al composite.
基金This work was supported by Hunan Provincial Natural Science Foundation.
文摘FeAl/TiC composites were fabricated by hot pressing blended elemental powders. The effects of Ni-doping on thedensification and mechanical properties of the composites were studied. Results show that the density of the composites decreases with the content of TiC increasing, and the addition of Ni significantly improves the densificationprocess by enhancing mass transfer in the bonding phase. The mechanical properties of the composites are closelyrelated with their porosity. Besides increasing the density of the composites, the addition of Ni improves the mechanical properties by other three effects: solution-strengthening the bonding phase, strengthening the FeAI-TiC interfaceand increasing ductile fracture in FeAl phase.
基金financially supported by the National Natural Science Foundation of China(No.21376276)the Specialfunded Program on National Key Scientific Instruments and Equipment Development of China(No.2012YQ230043)+1 种基金Guangdong Province Sci&Tech Bureau(Key Strategic Project No.2008A080800024)the Fundamental Research Funds for the Central Universities
文摘Relatively well crystallized and high aspect ratio Mg-Al layered double hydroxides（LDHs） were prepared by coprecipitation process in aqueous solution and further rehydrated to an organic modified LDH（OLDH） in the presence of surfactant. The intercalated structure and high aspect ratio of OLDH were verified by X-ray diffraction（XRD） and scanning electron microscopy（SEM）. A series of poly（propylene carbonate）（PPC）/OLDH composite films with different contents of OLDH were prepared via a melt-blending method. Their cross section morphologies, gas barrier properties and tensile strength were investigated as a function of OLDH contents. SEM results show that OLDH platelets are well dispersed within the composites and oriented parallel to the composite sheet plane. The gas barrier properties and tensile strength are obviously enhanced upon the incorporation of OLDH. Particularly, PPC/2%OLDH film exhibits the best barrier properties among all the composite films. Compared with pure PPC, the oxygen permeability coefficient（OP） and water vapor permeability coefficient（WVP） is reduced by 54% and 17% respectively with 2% OLDH addition. Furthermore, the tensile strength of PPC/2%OLDH is 83% higher than that of pure PPC with only small lose of elongation at break. Therefore, PPC/OLDH composite films show great potential application in packaging materials due to its biodegradable properties, superior oxygen and moisture barrier characteristics.
基金supported by a Research Grant of Pukyong National University(2013 Year)
文摘The tensile properties of 22Cr–2Ni–4Mn–0.2N micro-duplex stainless steels with different Ni and Mn contents were investigated. Duplex stainless steels were vacuum induction melted and hot rolled, then annealed at 1,000–1,100 °C, at which temperature both the austenite and ferrite phases were stable. The volume fraction of the ferrite phase was markedly affected by the alloying elements of Mn and Ni; 1 wt% of Mn was equivalent to 0.4 wt% of Ni. All of the steels tested at room temperature showed the common strain-hardening behavior, while the steels tested at lower temperatures（-30 or-50 °C）showed a distinct inflection point in their stress–strain curves, which resulted from the transformation of the austenite to straininduced martensite. The onset strain（e0） of the inflection point in the stress–strain curve depended on the Md30 value of the steel. Testing at lower temperatures resulted in smaller e0 and consequently higher strengths and fracture strains（ef）. The tensile behavior was examined from the perspective of austenite stability of the micro-duplex stainless steels with the different Ni and Mn contents.
文摘Erratum to:International Journal of Minerals, Metallurgy and Materials Volume 26, Number 9, September 2019, Page 1151https://doi.org/10.1007/s12613-019-1854-1The original version of this article unfortunately contained a mistake. The presentation of Fig. 11 was incorrect. The correct version is given below:
文摘Alumina-(0 similar to 20 vol. pct) iron composites were fabricated by hot-pressing of well-mixed-alumina and iron powders at 1400 degreesC and 30 MPa for 30 min. Hot-pressed bodies with nearly theoretical density were obtained for addition up to 10 vol. pct Fe, but relative density decreased gradually with further increase in Fe addition. The materials exhibit a homogeneous dispersion of Fe. Fracture strength of the composites exhibits a maximum value of 604 MPa at 15 vol. pct Fe, which is 1.5 times that of alumina alone. Fracture toughness increases with the increase in Fe content, reaching 7.5 MPa.m(1/2) at 20 vol. pct Fe. The theoretical values of fracture toughness was calculated and compared with the experimental one. Toughening mechanisms of the composites are also discussed.
文摘In spray atomization and codeposition, a molten stream of metal is disintegrated into a fine dispersion of droplets by high velocity gas jets. The resulting semi-solidified droplets are directed towards a substrate where they impact and collect as rapidly solidified splats. Relatively high rates of solidification are achieved as a result of the thinness of the splats and the rapid heat extraction during flight and upon impacting with the substrate. The processing method uses codeposition of the metallic semi-solidified droplets (metallic matrix) with the injected reinforcement ceramic particles. In the present paper, the microstructures, mechanical properties, interfacial properties, thermal stability and aging behaviour of spray atomized and codeposited Al-Li-X MMC's (injected X=SiC, Al2O3) are reported and correlated to the processing conditions.
基金financially supported by the National Natural Science Foundation of China(No.51363006)Science and Technology innovation key project of Hainan province(No.ZDXM20120090)National Science and Technology support project(No.2013BAF08B02)
文摘An effective procedure has been developed to synthesize the functionalized graphene oxide grafted by maleic anhydride grafted liquid polybutadiene（MLPB-GO）. Fourier transform spectroscopy and X-ray photoelectron spectroscopy indicate the successful functionalization of GO. The NR/MLPB-GO composites were then prepared by the co-coagulation process. The results show that the mechanical properties of NR/MLPB-GO composites are obviously superior to those of NR/GO composites and neat NR. Compared with neat NR, the tensile strength, modulus at 300% strain and tear strength of NR composite containing 2.12 phr MLPB-GO are significantly increased by 40.5%, 109.1% and 85.0%, respectively. Dynamic mechanical analysis results show that 84% increase in storage modulus and 2.9 K enhancement in the glass transition temperature of the composite have been achieved with the incorporation of 2.12 phr MLPB-GO into NR. The good dispersion of GO and the strong interface interaction in the composites are responsible for the unprecedented reinforcing efficiency of MLPB-GO towards NR.
基金Project(51302206)supported by the National Natural Science Foundation of ChinaProject(2013JK0925)supported by Shaanxi Provincial Department of Education,China+1 种基金Project(SKLSP201308)supported by the State Key Laboratory of Solidification Processing in Northwestern Polytechnical University,ChinaProject supported by the State Scholarship Fund,China
文摘The phase compositions and properties of Ti3SiC2-based composites with SiC addition of 5%-30% in mass fraction fabricated by in-situ reaction and hot pressing sintering were studied. SiC addition effectively prevented TiC synthesis but facilitated SiC synthesis. The Ti3SiC2/Ti C-SiC composite had better oxidation resistance when SiC added quantity reached 20% but poorer oxidation resistance with SiC addition under 15% than Ti3SiC2/TiC composite at higher temperatures. There were more than half of the original SiC and a few Ti3SiC2 remaining in Ti3SiC2/Ti C-SiC with 20% SiC addition, but all constituents in Ti3Si2/TiC composite were oxidized after 12 h in air at 1500 °C. The oxidation scale thickness of TS30, 1505.78 μm, was near a half of that of T,2715 μm, at 1500 °C for 20 h. Ti3SiC2/Ti C composite had a flexural strength of 474 MPa, which was surpassed by Ti3SiC2/TiC-SiC composites when SiC added amount reached 15%. The strength reached the peak of 518 MPa at 20% SiC added amount.
基金Project supported by National Natural Science Foundation of China(21376261,50971112,51001043,21173270)Natural Science Foundation of Hebei Province(E2010001170)Scientific Research Foundation for Returned Overseas Chinese Scholars of Hebei Province(20100501)
文摘LaFeO3 was used to improve the hydrogen storage properties of Mg H2. The Mg H2＋20 wt.%La Fe O3 composite was prepared by ball milling method. The composite could absorb 3.417 wt.% of hydrogen within 21 min at 423 K while Mg H2 only uptaked 0.977 wt.% hydrogen under the same conditions. The composite also released 3.894 wt.% of hydrogen at 623 K, which was almost twice more than Mg H2. The TPD measurement showed that the onset dissociation temperature of the composite was 570 K, 80 K lower than the Mg H2. Based on the Kissinger plot analysis of the composite, the activation energy E des was estimated to be 86.69 k J/mol, which was 36 k J/mol lower than Mg H2. The XRD and SEM results demonstrated that highly dispersed La Fe O3 could be presented in Mg H2, benefiting the reduction of particle size and also acting as an inhibitor to keep the particles from clustering during the ball-milled process.
基金National Natural Science Foundation of China(51075019)Aeronautical Science Foundation of China (20095251024)
文摘This paper proposes a new analytical solution to predict the shear modulus of a two-dimensional（2D） plain weave fabric（PWF） composite accounting for the interaction of orthogonal interlacing strands with coupled shear deformation modes including not only relative bending but also torsion,etc.The two orthogonal yarns in a micromechanical unit cell are idealized as curved beams with a path depicted by using sinusoidal shape functions.The internal forces and macroscopic deformations carried by the yarn families,together with macroscopic shear modulus of PWFs are derived by means of a strain energy approach founded on micromechanics.Three sets of experimental data pertinent to three kinds of 2D orthogonal PWF composites have been implemented to validate the new model.The calculations from the new model are also compared with those by using two models in the earlier literature.It is shown that the experimental results correlate well with predictions from the new model.
文摘Hoppressed Si3N4/SiC platelet composites had been investigated with respect to their microstructure and mechanical properties. The results indicate that Vickers hardness, elastic modulus and fracture toughness of the composites were increased by the addition of SiC platelet until the content up to 20 vol pct. A slight decrease in flexural Strength was measured at room temperature with increasing SiC platelet content. The high temperature flexural strength tests at 1150, 1250, and 1350℃ were conducted. It was found that the flexural strength at elevated temperature was degraded with the rising temperature, and the downward trend of flexural strength for the composite containing 10 vol. pct SiC platelet was less. The results indicate that SiC platelet had a positive influence on the high temperature strength. Effects of SiC platelet reinforcement were presented
基金the China Postdoctoral Science Foundation (20060400465)the National Natural Science Foundation of China (10702033)
文摘An equivalent continuum method only considering the stretching deformation of struts was used to study the in-plane stiffness and strength of planar lattice grid com- posite materials. The initial yield equations of lattices were deduced. Initial yield surfaces were depicted separately in different 3D and 2D stress spaces. The failure envelope is a polyhedron in 3D spaces and a polygon in 2D spaces. Each plane or line of the failure envelope is corresponding to the yield or buckling of a typical bar row. For lattices with more than three bar rows, subsequent yield of the other bar row after initial yield made the lattice achieve greater limit strength. The importance of the buckling strength of the grids was strengthened while the grids were relative sparse. The integration model of the method was used to study the nonlinear mechanical properties of strain hardening grids. It was shown that the integration equation could accurately model the complete stress-strain curves of the grids within small deformations.
基金the financial support from of the National Basic Research Program of China (Nos. 2012CB619600 and 2011CB012803)
文摘A facile ammonium-dichromate solution immersion method was introduced to synthesize the copperwettable Cr3C2 coating on and inside the carbon-carbon （C/C） preform. The formation mechanism and the microstructures of the Cr3C2 coatings were studied. The contact angle between molten copper and the C/C decreased from 140°to 60°, demonstrating the significant improvement in the wettability. The Cr3C2- coated C/C-Cu composite with only 4.2% porosity and 3.69 gcm^-3 density was manufactured through copper infiltration. As a result, the thermal and electrical conductivity of the modified C/C-Cu increased significantly due to the infiltrated copper. Also the mechanical properties of the composites including both the flexural and compressive strengths were enhanced by over 100%. The modified C/C-Cu composite exhibited lower friction coefficients and wear rates for different load levels than those of the commercial C/Cu composite. These results demonstrate the potential of the modified C/C-Cu material for use in electrical contacts.
基金Funded by the National Natural Science Foundation of China(No.51174244)the Foundational and Cutting-edge Research Plan of Chongqing,China(No.csts2013jcyj A50014)the Fundamental Research Funds for Central University,China(No.CDJZR12240056)
文摘Centrifugal casting was applied to produce cylindrical castings using SiCp/Al composite slurry,which contained 20%SiC particles.The castings comprised a particle free zone and a particle rich zone.The amount of SiC particles had a dramatic transformation from the particle rich zone to the particle free zone,and the maximum content of SiC particles in the particle rich zone reached up to 40 vol%.The ultimate tensile strength（UTS） of the as-cast SiCp / Al composites in the particle rich zone was 143 MPa,and the fracture was caused by the desorption of SiC particles from matrix alloy.The coefficient of thermal expansion（CTE） of the SiC_p / Al composites in the range of 20 and 100 ℃ was determined as 16.67×10^（-6） s^（-1）,and the experimental CTE was lower than the predicted data based on the Kerner＇s model.The results show that the decrease in CTE in the case of the composites at high temperature stage can be attributed to the solute concentration of Si in Al and the plastic deformation of the matrix alloy in the composites with void architecture.
