Low-frequency structural vibrations caused by poor rigidity are one of the main obstacles limiting the machining efficiency of robotic milling.Existing vibration suppression strategies primarily focus on passive vibra...Low-frequency structural vibrations caused by poor rigidity are one of the main obstacles limiting the machining efficiency of robotic milling.Existing vibration suppression strategies primarily focus on passive vibration absorption at the robotic end and feedback control at the joint motor.Although these strategies have a certain vibration suppression effect,the limitations of robotic flexibility and the extremely limited applicable speed range remain to be overcome.In this study,a Magnetorheological Joint Damper(MRJD)is developed.The joint-mounted feature ensures machining flexibility of the robot,and the millisecond response time of the Magnetorheological Fluid(MRF)ensures a large effective spindle speed range.More importantly,the evolution law of the damping performance of MRJD was revealed based on a low-frequency chatter mechanism,which guarantees the application of MRJD in robotic milling machining.To analyze the influence of the robotic joint angle on the suppression effect of the MRJD,the joint braking coefficient and end braking coefficient were proposed.Parallel coordinate plots were used to visualize the joint range with the optimal vibration suppression effect.Finally,a combination of different postures and cutting parameters was used to verify the vibration suppression effect and feasibility of the joint angle optimization.The experimental results show that the MRJD,which directly improves the joint vibration resistance,can effectively suppress the low-frequency vibration of robotic milling under a variety of cutting conditions.展开更多
Undesirable self-excited chatter has always been a typical issue restricting the improvement of robotic milling quality and efficiency.Sensitive chatter identification based on processing signals can prompt operators ...Undesirable self-excited chatter has always been a typical issue restricting the improvement of robotic milling quality and efficiency.Sensitive chatter identification based on processing signals can prompt operators to adjust the machining process and prevent chatter damage.Compared with the traditional machine tool,the uncertain multiple chatter frequency bands and the band-moving of the chatter frequency in robotic milling process make it more challenging to extract chatter information.This paper proposes a novel method of chatter identification using optimized variational mode decomposition(OVMD)with multi-band information fusion and compression technology(MT).During the robotic milling process,the number of decomposed modes k and the penalty coefficient a are optimized based on the dominant component of frequency scope partition and fitness of the mode center frequency.Moreover,the mayfly optimization algorithm(MA)is employed to obtain the global optimal parameter selection.In order to conquer information collection about the uncertain multiple chatter frequency bands and the band-moving of the chatter frequency in robotic milling process,MT is presented to reduce computation and extract signal characteristics.Finally,the cross entropy of the image(CEI)is proposed as the final chatter indicator to identify the chatter occurrence.The robotic milling experiments are carried out to verify the proposed method,and the results show that it can distinguish the robotic milling condition by extracting the uncertain multiple chatter frequency bands and overcome the band-moving of the chatter frequency in robotic milling process.展开更多
Chatter in the machining system can result in a decrease in tool life,poor surface finish,conservative cutting parameters,etc.Despite many review papers promoting the understanding and research of this area,chatter su...Chatter in the machining system can result in a decrease in tool life,poor surface finish,conservative cutting parameters,etc.Despite many review papers promoting the understanding and research of this area,chatter suppression techniques are generally discussed within limited pages in the framework of comprehensive chatter-related problems.In recent years,the developments of smart materials,advanced sensing techniques,and more effective control strategies have led to some new progress in chatter suppression.Meanwhile,the widely used thin-walled parts present more and more severe machining challenges in their milling processes.Considering the above deficiencies,this paper summarizes the current state of the art in milling chatter suppression.New classifications of chatter suppression techniques are proposed according to the working principle and control target.Based on the new classified framework,the mechanism and comparisons of different chatter suppression strategies are reviewed.Besides,the current challenges and potential tendencies of milling chatter suppression techniques are highlighted.Intellectualization,integration,compactness,adaptability to workpiece geometry,and the collaboration of multiple control methods are predicted to be important trends in the future.展开更多
Micro-milling technology is widely applied in micro manufacturing,particularly for the fabrication of miniature and micro components.However,the chatters and machining dynamics related issues in micro-milling are ofte...Micro-milling technology is widely applied in micro manufacturing,particularly for the fabrication of miniature and micro components.However,the chatters and machining dynamics related issues in micro-milling are often the main challenges restricting its machining quality and productivity.Many research works have rendered that the machining dynamics and chatters in micro-milling are more complex compared with the conventional macro-milling process,likely because of the size effect and rigidity of the micro-milling system including the tooling,workpiece,process variables,materials involved,and the high-speed milling machines,and further their collective dynamic effects.Therefore,in this paper,the state of the art focusing on micro-milling chatters and dynamics related issues over the past years are comprehensively and critically reviewed to provide some insights for potential researchers and practitioners.Firstly,typical applications and the problems caused by the machining dynamics and chatters in micro-milling have been put forward in this paper.Then,the research on the underlying micro-cutting mechanics and dynamics,stability analysis,chatters detection,and chatter suppression are summarized critically.Furthermore,the underlying scientific and technological challenges are discussed particularly against typical precision engineering applications.Finally,the possible future directions and trends in research and development of micro-milling have been discussed.展开更多
Considering the dynamic variation of roll gap and the transverse distribution of dynamic rolling force along the work roll width direction, the movement and deformation of rolls system, influenced by the coupling of v...Considering the dynamic variation of roll gap and the transverse distribution of dynamic rolling force along the work roll width direction, the movement and deformation of rolls system, influenced by the coupling of vertical chatter and transverse bending vibration, may cause instability and also bring product defect of thickness difference. Therefore, a rigid-flexible coupling vibration model of the rolls system was presented. The influence of dynamic characteristics on the rolling process stability and strip thickness distribution was investigated. Firstly, assuming the symmetry of upper and lower structures of six-high rolling mill, a transverse bending vibration model of three-beam system under simply supported boundary conditions was established, and a semi-analytical solution method was proposed to deal with this model. Then, considering both variation and change rate of the roll gap, a roll vertical chatter model with structure and process coupled was constructed, and the critical rolling speed for self-excited instability was determined by Routh stability criterion. Furthermore, a rigid-flexible coupling vibration model of the rolls system was built by connecting the vertical chatter model and transverse bending vibration model through the distribution of dynamic rolling force, and the dynamic characteristics of rolls system were analyzed. Finally, the strip exit thickness distributions under the stable and unstable rolling process were compared, and the product shape and thickness distribution characteristics were quantitatively evaluated by the crown and maximum longitudinal thickness difference.展开更多
In the high-speed cold tandem rolling process of thin plate,chatter or slip instability gives rise to the deterioration of equipment and product quality.Macroscopic instability behavior is closely related to interfaci...In the high-speed cold tandem rolling process of thin plate,chatter or slip instability gives rise to the deterioration of equipment and product quality.Macroscopic instability behavior is closely related to interfacial friction-lubrication con-dition which is generally characterized by the friction coefficient.However,with higher and higher speed requirements,the commonly used model of friction coefficient is no longer applicable and accurate.A novel approach is suggested to calculate the speed-dependent friction coefficient,in which the viscosity-pressure-temperature effects of the lubricant,surface roughness states of work rolls and rolled piece are comprehensively involved and the mixed flm lubrication theory is applied.Subsequently,the influences of friction coefficient on the instability of slip and chatter are investigated for a five-stand cold tandem rolling mill.On one side,the critical friction coefficient for each stand is determined by calculating the corresponding slip factor;on the other hand,the friction coefficient varying with rolling speed is combined with the model of theoretical critical rolling speed presented under constant friction coefficient,so that the speed threshold is determined.Furthermore,the stable and unstable regions corresponding to the rear three stands are individually discussed,and the technical strategies are proposed to suppress both slip and chatter frequently occurring in the actual rolling process.展开更多
The possibility of the electric-hydraulic chattering technology and its application in the cold extrusion were presented.The conventional and electric-hydraulic chattering assisted backward extrusion processes were pe...The possibility of the electric-hydraulic chattering technology and its application in the cold extrusion were presented.The conventional and electric-hydraulic chattering assisted backward extrusion processes were performed on 6061 aluminum alloy billets at room temperature.The experimental results showed that 5.65% reduction in the extrusion load was attained if the die and ejector were vibrated at a frequency of 100 Hz and amplitude of 0.013 mm in the longitudinal direction.The friction coefficient at the billet and tool system interface determined from the finite element analysis（FEA） decreased from 0.2 without chattering to 0.1 with application of electric-hydraulic chattering.The higher values of instantaneous velocity and direction change of material flow were achieved during the chattering assisted backward extrusion process.The strain distribution of the chattering assisted backward extrusion billet revealed lower maximum strain and smoother strain distribution in comparison with that produced by the conventional extrusion method.展开更多
Considering the deficiency in milling process parameters selection, based on the modelling of dynamic milling force and the deduction of chatter stability limits, the chatter stability lobes simulation program for mil...Considering the deficiency in milling process parameters selection, based on the modelling of dynamic milling force and the deduction of chatter stability limits, the chatter stability lobes simulation program for milling is developed with MAT- LAB. The simulation optimization application software of dynamics was designed using engineering simulation software Visio Basic. The chatter stability lobes for milling, which can be used as an instruction guide for the selection of process parameters, are simulated with frequency response functions （FRFs） gained by hammer test. The validation and accuracy of the simulation algorithm are verified by experiments. The simulation method has been used in a factory with an excellent application effect.展开更多
A new method for suppressing cutting chatter is studied by adjusting servo parameters of the numerical control （NC） machine tool and controlling the limited cutting width. A model of the cutting system of the NC mac...A new method for suppressing cutting chatter is studied by adjusting servo parameters of the numerical control （NC） machine tool and controlling the limited cutting width. A model of the cutting system of the NC machine tool is established. It includes the mechanical system, the servo system and the cutting chatter system. Interactions between every two systems are shown in the model. The cutting system stability is simulated and relation curves between the limited cutting width and servo system parameters are described in the experiment. Simulation and experimental results show that there is a mapping relation between the limited cutting width and servo parameters of the NC machine tool, and the method is applicable and credible to suppress chatter.展开更多
An applicable method to control regenerative cutting chatter automatically based on the optimal regulation of spindle speed is introduced. The optimal value of the phase shift angle of the regenerative chatter signal ...An applicable method to control regenerative cutting chatter automatically based on the optimal regulation of spindle speed is introduced. The optimal value of the phase shift angle of the regenerative chatter signal between the two successive cuts is 270°. The cutting process can be adjusted from the unstable region to stable one whenever regenerative chatter occurs if the phase shift angle is kept 270° by the optimal regulation of spindle speed. The theoretical analysis and the experimental results prove that the optimal regulation of spindle speed can effectively control regenerative cutting chatter. In addition, a reliablelly optimal control system of reliable spindle speed is presented. There is no need for system identification of the machine tool, and it is easy to put this regenerative chatter control method into practice, so the method has excellent application prospect.展开更多
Chatter is a self-excited vibration of parts in machining systems. It is widely present across a range of cutting processes, and has an impact upon both efficiency and quality in production processing. A great deal of...Chatter is a self-excited vibration of parts in machining systems. It is widely present across a range of cutting processes, and has an impact upon both efficiency and quality in production processing. A great deal of research has been dedicated to the development of technologies that are able to predict and detect chatter. The purpose of these technologies is to facilitate the avoidance of chatter during cutting processes, which leads to better surface precision, higher productivity,and longer tool life. This paper summarizes the current state of the art in research regarding the problems of how to arrive at stable chatter prediction, chatter identification, and chatter control/-suppression, with a focus on milling processes. Particular focus is placed on the theoretical relationship between cutting chatter and process damping, tool runout, and gyroscopic effect, as well as the importance of this for chatter prediction. The paper concludes with some reflections regarding possible directions for future research in this field.展开更多
Grinding chatter is a self?induced vibration which is unfavorable to precision machining processes. This paper proposes a forecasting method for grinding state identification based on bivarition empirical mode decompo...Grinding chatter is a self?induced vibration which is unfavorable to precision machining processes. This paper proposes a forecasting method for grinding state identification based on bivarition empirical mode decomposition(BEMD) and least squares support vector machine(LSSVM), which allows the monitoring of grinding chatter over time. BEMD is a promising technique in signal processing research which involves the decomposition of two?dimen?sional signals into a series of bivarition intrinsic mode functions(BIMFs). BEMD and the extraction criterion of its true BIMFs are investigated by processing a complex?value simulation chatter signal. Then the feature vectors which are employed as an amplification for the chatter premonition are discussed. Furthermore, the methodology is tested and validated by experimental data collected from a CNC guideway grinder KD4020 X16 in Hangzhou Hangji Machine Tool Co., Ltd. The results illustrate that the BEMD is a superior method in terms of processing non?stationary and nonlinear signals. Meanwhile, the peak to peak, real?time standard deviation and instantaneous energy are proven to be e ec?tive feature vectors which reflect the di erent grinding states. Finally, a LSSVM model is established for grinding status classification based on feature vectors, giving a prediction accuracy rate of 96%.展开更多
In order to build high accuracy integral dynamic models of cold rolling mill system, by analyzing the vibration process of cold rolling, the dynamic model of 4-h mill, including the rolling process model, the mill rol...In order to build high accuracy integral dynamic models of cold rolling mill system, by analyzing the vibration process of cold rolling, the dynamic model of 4-h mill, including the rolling process model, the mill roll stand structure model and the hydraulic servo system model is built. These three models are coupled and linearized, then the multiple input and multiple output （MIMO） linear transfer function model of single stand 4-h cold mill system is obtained. The model with the proposed data proves its validity, meanwhile the effects of different working conditions on the stability of cold rolling mill system have been discussed. Simulation resulsts show that the model accords with former models and has its own advancement. It contributes to the further study and supression of coupling vibraiton.展开更多
An analytical model for chatter aero-engine casings is presented in this paper stability prediction in bull-nose end milling of And the mechanics and dynamics variations due to the complex cutter and workpiece geomet...An analytical model for chatter aero-engine casings is presented in this paper stability prediction in bull-nose end milling of And the mechanics and dynamics variations due to the complex cutter and workpiece geometry are considered by analyzing the effects of the lead angle on the milling process. Firstly, the tool-workpiece engagement region is obtained by using a previously developed method and divided into several disk elements along the tool-axis direction. Secondly, a 3D dynamic model for stability limit calculation is developed and simplified into a 1D model in normal direction considering only the dominant mode of the workpiece. Then the cutting force coefficients, the start and exit angles corresponding to each disk element are determined. And the total stability lobe diagram is calculated using an iterative algorithm. Finally, several experimental tests are carried out to validate the feasibility and effectiveness of the proposed ~rediction approach.展开更多
Currently, the modeling of cutting process mainly focuses on two aspects: one is the setup of the universal cutting force model that can be adapted to a broader cutting condition; the other is the setup of the exact c...Currently, the modeling of cutting process mainly focuses on two aspects: one is the setup of the universal cutting force model that can be adapted to a broader cutting condition; the other is the setup of the exact cutting force model that can accurately reflect a true cutting process. However, there is little research on the prediction of chatter stablity in milling. Based on the generalized mathematical model of inserted cutters introduced by ENGIN, an improved geometrical, mechanical and dynamic model for the vast variety of inserted cutters widely used in engineering applications is presented, in which the average directional cutting force coefficients are obtained by means of a numerical approach, thus leading to an analytical determination of stability lobes diagram (SLD) on the axial depth of cut. A new kind of SLD on the radial depth of cut is also created to satisfy the special requirement of inserted cutter milling. The corresponding algorithms used for predicting cutting forces, vibrations, dimensional surface finish and stability lobes in inserted cutter milling under different cutting conditions are put forward. Thereafter, a dynamic simulation module of inserted cutter milling is implemented by using hybrid program of Matlab with Visual Basic. Verification tests are conducted on a vertical machine center for Aluminum alloy LC4 by using two different types of inserted cutters, and the effectiveness of the model and the algorithm is verified by the good agreement of simulation result with that of cutting tests under different cutting conditions. The proposed model can predict the cutting process accurately under a variety of cutting conditions, and a high efficient and chatter-free milling operation can be achieved by a cutting condition optimization in industry applications.展开更多
Modals of the machine/tool and machine/part system are the principal factors affecting the stability of a milling process. Based on the modeling of chatter stability of milling process,the influence of modal parameter...Modals of the machine/tool and machine/part system are the principal factors affecting the stability of a milling process. Based on the modeling of chatter stability of milling process,the influence of modal parameters on chatter stability lobes independently or jointly has been analyzed by simulation. Peak-to-valley specific value,lobe coefficient and the corresponding calculation formula have been put forward. General laws and steps of modal simplification for multimodality system have been summarized.展开更多
T-slot milling is one of the most common milling processes in industry. Despite recent advances in machining technology, productivity of T-slot milling is usually limited due to the process limitations such as high cu...T-slot milling is one of the most common milling processes in industry. Despite recent advances in machining technology, productivity of T-slot milling is usually limited due to the process limitations such as high cutting forces and stability. If cutting conditions are not selected properly the process may result in the poor surface finish of the workpiece and the potential damage to the machine tool. Currently, the predication of chatter stability and determination of optimal cutting conditions based on the modeling of T-slot milling process is an effective way to improve the material removal rate（MRR） of a T-slot milling operation. Based on the geometrical model of the T-slot cutter, the dynamic cutting force model was presented in which the average directional cutting force coefficients were obtained by means of numerical approach, and leads to an analytical determination of stability lobes diagram（SLD） on the axial depth of cut. A new kind of SLD on the radial depth of cut was also created to satisfy the special requirement of T-slot milling. Thereafter, a dynamic simulation model of T-slot milling was implemented using Matlab software. In order to verify the effectiveness of the approach, the transfer functions of a typical cutting system in a vertical CNC machining center were measured in both feed and normal directions by an instrumented hammer and accelerators. Dynamic simulations were conducted to obtain the predicated SLD under specified cutting conditions with both the proposed model and CutPro~. Meanwhile, a set of cutting trials were conducted to reveal whether the cutting process under specified cutting conditions is stable or not. Both the simulation comparison and experimental verification demonstrated that the satisfactory coincidence between the simulated, the predicted and the experimental results. The chatter-free T-slot milling with higher MRR can be achieved under the cutting conditions determined according to the SLD simulation.展开更多
The tuned mass damper（TMD） has been successfully applied to the vibration control in machining, while the most widely adopted tuning is equal peaks, which splits the magnitude of the frequency response function（FRF...The tuned mass damper（TMD） has been successfully applied to the vibration control in machining, while the most widely adopted tuning is equal peaks, which splits the magnitude of the frequency response function（FRF） into equal peaks. However, chatter is a special self-excited problem and a chatter-flee machining is determined by FRF at the cutting zone. A TMD tuning aiming at achieving the maximum chatter stability is studied, and it is formulated as an optimization problem of maximizing the minimum negative real part of FRF. By employing the steepest descend method, the optimum frequency and damping ratio of TMD are obtained, and they are compared against the equal peaks tuning. The advantage of the proposed tuning is demonstrated numerically by comparing the minimum point of the negative real part, and is further verified by damping a flexible mode from the fixture of a turning machine. A TMD is designed and placed on the fixture along the vibration of the target mode after performing modal analysis and mode shape visualization. Both of the above two ttmings are applied to modify the tool point FRF by tuning TMD respectively. Chatter stability chart of the turning shows that the proposed tuning can increase the critical depth of cut 37% more than the equal peaks. Cutting tests with an increasing depth of cut are conducted on the turning machine in order to distinguish the stability limit. The tool vibrations during the machining are compared to validate the simulation results. The proposed damping design and optimization routine are able to further increase the chatter suppression effect.展开更多
In order to avoid the accuracy deterioration or tool damage caused by milling chatter, it is necessary to have an efficient and reliable diagnosis system that can on-line predict/detect the occur-rence of chatter. The...In order to avoid the accuracy deterioration or tool damage caused by milling chatter, it is necessary to have an efficient and reliable diagnosis system that can on-line predict/detect the occur-rence of chatter. The diagnosis/predicting system proposed is to on-line process and analysis the vi-bration signals of the milling machine measured by accelerometers. According to the analysis results, the system will be able to detect/predict the occurrence of the chatter. The diagnosis algorithm is, first, collecting both the normal signals and chatter signals from milling processes, and then, converting the signals through wavelet transform and fast Fourier transform （FFT）. Since the converted chatter sig-nals exhibit different characteristics from the normal signals, through defining the characteristic val-ues, such as root-mean-square value, max value, and ratio of peak value to root-mean-square value, etc, a diagnosis reference library that contains the distribution of these characteristic values is built for diagnosis. When a diagnosis is executing, the characteristic value of the measured signals is con-trasted with the diagnosis reference. The approach index which shows the possibility of occurrence of milling chatter will, then, be calculated through the diagnosis system. Cutting experiments are con-ducted to verify the proposed diagnosis system. The results show the success of early chatter detecting for the system.展开更多
A new method is proposed to suppress chatter, in which the ultrasonic elliptical vibration is added on the cutting tool edge. It results in the fact that the rake face of tool is separated from the chip and the direct...A new method is proposed to suppress chatter, in which the ultrasonic elliptical vibration is added on the cutting tool edge. It results in the fact that the rake face of tool is separated from the chip and the direction of the frictional force between the rake face and the chip is reversed in each cycle of elliptical vibration cutting. The experimental investigations show that the chatter can be suppressed effectively by adding ultrasonic elliptical vibration on the cutting tool edge. In order to make clear the reason of chatter suppression, the mechanism of chatter suppression is analyzed theoretically from the viewpoint of energy.展开更多
基金supported by the National Natural Science Foundation of China(No.U20A20294)the National Natural Science Foundation of China(No.52322511)the National Natural Science Foundation of China(No.52188102).
文摘Low-frequency structural vibrations caused by poor rigidity are one of the main obstacles limiting the machining efficiency of robotic milling.Existing vibration suppression strategies primarily focus on passive vibration absorption at the robotic end and feedback control at the joint motor.Although these strategies have a certain vibration suppression effect,the limitations of robotic flexibility and the extremely limited applicable speed range remain to be overcome.In this study,a Magnetorheological Joint Damper(MRJD)is developed.The joint-mounted feature ensures machining flexibility of the robot,and the millisecond response time of the Magnetorheological Fluid(MRF)ensures a large effective spindle speed range.More importantly,the evolution law of the damping performance of MRJD was revealed based on a low-frequency chatter mechanism,which guarantees the application of MRJD in robotic milling machining.To analyze the influence of the robotic joint angle on the suppression effect of the MRJD,the joint braking coefficient and end braking coefficient were proposed.Parallel coordinate plots were used to visualize the joint range with the optimal vibration suppression effect.Finally,a combination of different postures and cutting parameters was used to verify the vibration suppression effect and feasibility of the joint angle optimization.The experimental results show that the MRJD,which directly improves the joint vibration resistance,can effectively suppress the low-frequency vibration of robotic milling under a variety of cutting conditions.
基金supported by the Civil Aircraft Project(No.MJZ4-1N22),National Natural Science Foundation of China(No.51975053)Inversion and Application Project of Outcome(Nos.D44F9A65 and 2B0188E1)+1 种基金Key R&D Program of Inner Mongolia(No.2022YFHH0121)the Basic Research Fund of Beijing Institute of Technology(No.2021CX01023).
文摘Undesirable self-excited chatter has always been a typical issue restricting the improvement of robotic milling quality and efficiency.Sensitive chatter identification based on processing signals can prompt operators to adjust the machining process and prevent chatter damage.Compared with the traditional machine tool,the uncertain multiple chatter frequency bands and the band-moving of the chatter frequency in robotic milling process make it more challenging to extract chatter information.This paper proposes a novel method of chatter identification using optimized variational mode decomposition(OVMD)with multi-band information fusion and compression technology(MT).During the robotic milling process,the number of decomposed modes k and the penalty coefficient a are optimized based on the dominant component of frequency scope partition and fitness of the mode center frequency.Moreover,the mayfly optimization algorithm(MA)is employed to obtain the global optimal parameter selection.In order to conquer information collection about the uncertain multiple chatter frequency bands and the band-moving of the chatter frequency in robotic milling process,MT is presented to reduce computation and extract signal characteristics.Finally,the cross entropy of the image(CEI)is proposed as the final chatter indicator to identify the chatter occurrence.The robotic milling experiments are carried out to verify the proposed method,and the results show that it can distinguish the robotic milling condition by extracting the uncertain multiple chatter frequency bands and overcome the band-moving of the chatter frequency in robotic milling process.
基金co-supported by the National Natural Science Foundation of China(No.52275445)the Key Research and Development Plan of Shandong Province(Nos.2020CXGC010204,2023CXPT014,and 2021JMRH0301).
文摘Chatter in the machining system can result in a decrease in tool life,poor surface finish,conservative cutting parameters,etc.Despite many review papers promoting the understanding and research of this area,chatter suppression techniques are generally discussed within limited pages in the framework of comprehensive chatter-related problems.In recent years,the developments of smart materials,advanced sensing techniques,and more effective control strategies have led to some new progress in chatter suppression.Meanwhile,the widely used thin-walled parts present more and more severe machining challenges in their milling processes.Considering the above deficiencies,this paper summarizes the current state of the art in milling chatter suppression.New classifications of chatter suppression techniques are proposed according to the working principle and control target.Based on the new classified framework,the mechanism and comparisons of different chatter suppression strategies are reviewed.Besides,the current challenges and potential tendencies of milling chatter suppression techniques are highlighted.Intellectualization,integration,compactness,adaptability to workpiece geometry,and the collaboration of multiple control methods are predicted to be important trends in the future.
基金supported by the National Natural Science Foundation of China(No.52075129).
文摘Micro-milling technology is widely applied in micro manufacturing,particularly for the fabrication of miniature and micro components.However,the chatters and machining dynamics related issues in micro-milling are often the main challenges restricting its machining quality and productivity.Many research works have rendered that the machining dynamics and chatters in micro-milling are more complex compared with the conventional macro-milling process,likely because of the size effect and rigidity of the micro-milling system including the tooling,workpiece,process variables,materials involved,and the high-speed milling machines,and further their collective dynamic effects.Therefore,in this paper,the state of the art focusing on micro-milling chatters and dynamics related issues over the past years are comprehensively and critically reviewed to provide some insights for potential researchers and practitioners.Firstly,typical applications and the problems caused by the machining dynamics and chatters in micro-milling have been put forward in this paper.Then,the research on the underlying micro-cutting mechanics and dynamics,stability analysis,chatters detection,and chatter suppression are summarized critically.Furthermore,the underlying scientific and technological challenges are discussed particularly against typical precision engineering applications.Finally,the possible future directions and trends in research and development of micro-milling have been discussed.
基金supported by the National Natural Science Foundation of China(No.51775038).
文摘Considering the dynamic variation of roll gap and the transverse distribution of dynamic rolling force along the work roll width direction, the movement and deformation of rolls system, influenced by the coupling of vertical chatter and transverse bending vibration, may cause instability and also bring product defect of thickness difference. Therefore, a rigid-flexible coupling vibration model of the rolls system was presented. The influence of dynamic characteristics on the rolling process stability and strip thickness distribution was investigated. Firstly, assuming the symmetry of upper and lower structures of six-high rolling mill, a transverse bending vibration model of three-beam system under simply supported boundary conditions was established, and a semi-analytical solution method was proposed to deal with this model. Then, considering both variation and change rate of the roll gap, a roll vertical chatter model with structure and process coupled was constructed, and the critical rolling speed for self-excited instability was determined by Routh stability criterion. Furthermore, a rigid-flexible coupling vibration model of the rolls system was built by connecting the vertical chatter model and transverse bending vibration model through the distribution of dynamic rolling force, and the dynamic characteristics of rolls system were analyzed. Finally, the strip exit thickness distributions under the stable and unstable rolling process were compared, and the product shape and thickness distribution characteristics were quantitatively evaluated by the crown and maximum longitudinal thickness difference.
基金supported by the National Natural Science Foundation of China(Grant No.51775038).
文摘In the high-speed cold tandem rolling process of thin plate,chatter or slip instability gives rise to the deterioration of equipment and product quality.Macroscopic instability behavior is closely related to interfacial friction-lubrication con-dition which is generally characterized by the friction coefficient.However,with higher and higher speed requirements,the commonly used model of friction coefficient is no longer applicable and accurate.A novel approach is suggested to calculate the speed-dependent friction coefficient,in which the viscosity-pressure-temperature effects of the lubricant,surface roughness states of work rolls and rolled piece are comprehensively involved and the mixed flm lubrication theory is applied.Subsequently,the influences of friction coefficient on the instability of slip and chatter are investigated for a five-stand cold tandem rolling mill.On one side,the critical friction coefficient for each stand is determined by calculating the corresponding slip factor;on the other hand,the friction coefficient varying with rolling speed is combined with the model of theoretical critical rolling speed presented under constant friction coefficient,so that the speed threshold is determined.Furthermore,the stable and unstable regions corresponding to the rear three stands are individually discussed,and the technical strategies are proposed to suppress both slip and chatter frequently occurring in the actual rolling process.
基金Project(51275475)supported by the National Natural Science Foundation of ChinaProject(2014BY001)supported by the Department of Education in Zhejiang Province,ChinaProject(2014EP0110)supported by the Key Laboratory of Special Purpose Equipment and Advanced Manufacturing Technology,Ministry of Education and Zhejiang Province,China
文摘The possibility of the electric-hydraulic chattering technology and its application in the cold extrusion were presented.The conventional and electric-hydraulic chattering assisted backward extrusion processes were performed on 6061 aluminum alloy billets at room temperature.The experimental results showed that 5.65% reduction in the extrusion load was attained if the die and ejector were vibrated at a frequency of 100 Hz and amplitude of 0.013 mm in the longitudinal direction.The friction coefficient at the billet and tool system interface determined from the finite element analysis（FEA） decreased from 0.2 without chattering to 0.1 with application of electric-hydraulic chattering.The higher values of instantaneous velocity and direction change of material flow were achieved during the chattering assisted backward extrusion process.The strain distribution of the chattering assisted backward extrusion billet revealed lower maximum strain and smoother strain distribution in comparison with that produced by the conventional extrusion method.
基金Tianjin Municipal Association of Higher Vocational&Technical Education Projects(No.XIV412)
文摘Considering the deficiency in milling process parameters selection, based on the modelling of dynamic milling force and the deduction of chatter stability limits, the chatter stability lobes simulation program for milling is developed with MAT- LAB. The simulation optimization application software of dynamics was designed using engineering simulation software Visio Basic. The chatter stability lobes for milling, which can be used as an instruction guide for the selection of process parameters, are simulated with frequency response functions （FRFs） gained by hammer test. The validation and accuracy of the simulation algorithm are verified by experiments. The simulation method has been used in a factory with an excellent application effect.
文摘A new method for suppressing cutting chatter is studied by adjusting servo parameters of the numerical control （NC） machine tool and controlling the limited cutting width. A model of the cutting system of the NC machine tool is established. It includes the mechanical system, the servo system and the cutting chatter system. Interactions between every two systems are shown in the model. The cutting system stability is simulated and relation curves between the limited cutting width and servo system parameters are described in the experiment. Simulation and experimental results show that there is a mapping relation between the limited cutting width and servo parameters of the NC machine tool, and the method is applicable and credible to suppress chatter.
文摘An applicable method to control regenerative cutting chatter automatically based on the optimal regulation of spindle speed is introduced. The optimal value of the phase shift angle of the regenerative chatter signal between the two successive cuts is 270°. The cutting process can be adjusted from the unstable region to stable one whenever regenerative chatter occurs if the phase shift angle is kept 270° by the optimal regulation of spindle speed. The theoretical analysis and the experimental results prove that the optimal regulation of spindle speed can effectively control regenerative cutting chatter. In addition, a reliablelly optimal control system of reliable spindle speed is presented. There is no need for system identification of the machine tool, and it is easy to put this regenerative chatter control method into practice, so the method has excellent application prospect.
基金supported by Projects of International Cooperation and Exchanges NSFC (51720105009)the National Natural Science Foundation of China (No. 51575147)the Youth Talent Support Program of Harbin University of Science and Technology (201507)
文摘Chatter is a self-excited vibration of parts in machining systems. It is widely present across a range of cutting processes, and has an impact upon both efficiency and quality in production processing. A great deal of research has been dedicated to the development of technologies that are able to predict and detect chatter. The purpose of these technologies is to facilitate the avoidance of chatter during cutting processes, which leads to better surface precision, higher productivity,and longer tool life. This paper summarizes the current state of the art in research regarding the problems of how to arrive at stable chatter prediction, chatter identification, and chatter control/-suppression, with a focus on milling processes. Particular focus is placed on the theoretical relationship between cutting chatter and process damping, tool runout, and gyroscopic effect, as well as the importance of this for chatter prediction. The paper concludes with some reflections regarding possible directions for future research in this field.
基金National Natural Science Foundation of China(Grant No.51475432)Zhejiang Provincial National Natural Science Foundation of China(Grant No.LZ13E050003)State Key Program of National Natural Science of China(Grant Nos.U1234207,U1709210)
文摘Grinding chatter is a self?induced vibration which is unfavorable to precision machining processes. This paper proposes a forecasting method for grinding state identification based on bivarition empirical mode decomposition(BEMD) and least squares support vector machine(LSSVM), which allows the monitoring of grinding chatter over time. BEMD is a promising technique in signal processing research which involves the decomposition of two?dimen?sional signals into a series of bivarition intrinsic mode functions(BIMFs). BEMD and the extraction criterion of its true BIMFs are investigated by processing a complex?value simulation chatter signal. Then the feature vectors which are employed as an amplification for the chatter premonition are discussed. Furthermore, the methodology is tested and validated by experimental data collected from a CNC guideway grinder KD4020 X16 in Hangzhou Hangji Machine Tool Co., Ltd. The results illustrate that the BEMD is a superior method in terms of processing non?stationary and nonlinear signals. Meanwhile, the peak to peak, real?time standard deviation and instantaneous energy are proven to be e ec?tive feature vectors which reflect the di erent grinding states. Finally, a LSSVM model is established for grinding status classification based on feature vectors, giving a prediction accuracy rate of 96%.
基金Item Sponsored by National Natural Science Foundation of China(60374032)Beijing Municipal Education Commission Key Discipline Control Theory and Control Engineering of China(XK100080537)
文摘In order to build high accuracy integral dynamic models of cold rolling mill system, by analyzing the vibration process of cold rolling, the dynamic model of 4-h mill, including the rolling process model, the mill roll stand structure model and the hydraulic servo system model is built. These three models are coupled and linearized, then the multiple input and multiple output （MIMO） linear transfer function model of single stand 4-h cold mill system is obtained. The model with the proposed data proves its validity, meanwhile the effects of different working conditions on the stability of cold rolling mill system have been discussed. Simulation resulsts show that the model accords with former models and has its own advancement. It contributes to the further study and supression of coupling vibraiton.
基金supported by the National Basic Research Program of China(No.2013CB035802)the 111 Project of China(No.B13044)
文摘An analytical model for chatter aero-engine casings is presented in this paper stability prediction in bull-nose end milling of And the mechanics and dynamics variations due to the complex cutter and workpiece geometry are considered by analyzing the effects of the lead angle on the milling process. Firstly, the tool-workpiece engagement region is obtained by using a previously developed method and divided into several disk elements along the tool-axis direction. Secondly, a 3D dynamic model for stability limit calculation is developed and simplified into a 1D model in normal direction considering only the dominant mode of the workpiece. Then the cutting force coefficients, the start and exit angles corresponding to each disk element are determined. And the total stability lobe diagram is calculated using an iterative algorithm. Finally, several experimental tests are carried out to validate the feasibility and effectiveness of the proposed ~rediction approach.
基金supported by Hunan Provincial Natural Science Foundation of China (Grant Nos. 10JJ2040, 11JJ3055)National Major Science and Technology Special Projects of China (Grant No.2012ZX04011-011)+1 种基金Postdoctoral Science Funded Project of China (GrantNo. 20110490261)Hunan Provincial 12th Five-year Plan Key Disciplines of China (Grant No. 2012-42)
文摘Currently, the modeling of cutting process mainly focuses on two aspects: one is the setup of the universal cutting force model that can be adapted to a broader cutting condition; the other is the setup of the exact cutting force model that can accurately reflect a true cutting process. However, there is little research on the prediction of chatter stablity in milling. Based on the generalized mathematical model of inserted cutters introduced by ENGIN, an improved geometrical, mechanical and dynamic model for the vast variety of inserted cutters widely used in engineering applications is presented, in which the average directional cutting force coefficients are obtained by means of a numerical approach, thus leading to an analytical determination of stability lobes diagram (SLD) on the axial depth of cut. A new kind of SLD on the radial depth of cut is also created to satisfy the special requirement of inserted cutter milling. The corresponding algorithms used for predicting cutting forces, vibrations, dimensional surface finish and stability lobes in inserted cutter milling under different cutting conditions are put forward. Thereafter, a dynamic simulation module of inserted cutter milling is implemented by using hybrid program of Matlab with Visual Basic. Verification tests are conducted on a vertical machine center for Aluminum alloy LC4 by using two different types of inserted cutters, and the effectiveness of the model and the algorithm is verified by the good agreement of simulation result with that of cutting tests under different cutting conditions. The proposed model can predict the cutting process accurately under a variety of cutting conditions, and a high efficient and chatter-free milling operation can be achieved by a cutting condition optimization in industry applications.
基金Supported by the Fundamental Research Project of COSTI ND(K1203020507)
文摘Modals of the machine/tool and machine/part system are the principal factors affecting the stability of a milling process. Based on the modeling of chatter stability of milling process,the influence of modal parameters on chatter stability lobes independently or jointly has been analyzed by simulation. Peak-to-valley specific value,lobe coefficient and the corresponding calculation formula have been put forward. General laws and steps of modal simplification for multimodality system have been summarized.
基金supported by National Science and Technology Support Program of China (Grant No. 2006BAF01B09-03)the Research Fund for the Doctoral Program of Higher Education of China (Grant No. 200800060010)Hunan Provincial Educational Department Scientific Research Project of China (Grant No. 08D096)
文摘T-slot milling is one of the most common milling processes in industry. Despite recent advances in machining technology, productivity of T-slot milling is usually limited due to the process limitations such as high cutting forces and stability. If cutting conditions are not selected properly the process may result in the poor surface finish of the workpiece and the potential damage to the machine tool. Currently, the predication of chatter stability and determination of optimal cutting conditions based on the modeling of T-slot milling process is an effective way to improve the material removal rate（MRR） of a T-slot milling operation. Based on the geometrical model of the T-slot cutter, the dynamic cutting force model was presented in which the average directional cutting force coefficients were obtained by means of numerical approach, and leads to an analytical determination of stability lobes diagram（SLD） on the axial depth of cut. A new kind of SLD on the radial depth of cut was also created to satisfy the special requirement of T-slot milling. Thereafter, a dynamic simulation model of T-slot milling was implemented using Matlab software. In order to verify the effectiveness of the approach, the transfer functions of a typical cutting system in a vertical CNC machining center were measured in both feed and normal directions by an instrumented hammer and accelerators. Dynamic simulations were conducted to obtain the predicated SLD under specified cutting conditions with both the proposed model and CutPro~. Meanwhile, a set of cutting trials were conducted to reveal whether the cutting process under specified cutting conditions is stable or not. Both the simulation comparison and experimental verification demonstrated that the satisfactory coincidence between the simulated, the predicted and the experimental results. The chatter-free T-slot milling with higher MRR can be achieved under the cutting conditions determined according to the SLD simulation.
基金supported by National Technology Support Program of China (Grant No. 2006BAF01B09)Doctoral Foundation of Ministry of Education of China (Grant No. 200800060010)+1 种基金Beijing Municipal Key Laboratory Project of Chinasupport from the Manufacturing Automation Laboratory(MAL) of the University of British Columbia
文摘The tuned mass damper（TMD） has been successfully applied to the vibration control in machining, while the most widely adopted tuning is equal peaks, which splits the magnitude of the frequency response function（FRF） into equal peaks. However, chatter is a special self-excited problem and a chatter-flee machining is determined by FRF at the cutting zone. A TMD tuning aiming at achieving the maximum chatter stability is studied, and it is formulated as an optimization problem of maximizing the minimum negative real part of FRF. By employing the steepest descend method, the optimum frequency and damping ratio of TMD are obtained, and they are compared against the equal peaks tuning. The advantage of the proposed tuning is demonstrated numerically by comparing the minimum point of the negative real part, and is further verified by damping a flexible mode from the fixture of a turning machine. A TMD is designed and placed on the fixture along the vibration of the target mode after performing modal analysis and mode shape visualization. Both of the above two ttmings are applied to modify the tool point FRF by tuning TMD respectively. Chatter stability chart of the turning shows that the proposed tuning can increase the critical depth of cut 37% more than the equal peaks. Cutting tests with an increasing depth of cut are conducted on the turning machine in order to distinguish the stability limit. The tool vibrations during the machining are compared to validate the simulation results. The proposed damping design and optimization routine are able to further increase the chatter suppression effect.
基金Selected from Proceedings of the 7th International Conference on Frontierof Design and Manufacturing(ICFDM’2006).
文摘In order to avoid the accuracy deterioration or tool damage caused by milling chatter, it is necessary to have an efficient and reliable diagnosis system that can on-line predict/detect the occur-rence of chatter. The diagnosis/predicting system proposed is to on-line process and analysis the vi-bration signals of the milling machine measured by accelerometers. According to the analysis results, the system will be able to detect/predict the occurrence of the chatter. The diagnosis algorithm is, first, collecting both the normal signals and chatter signals from milling processes, and then, converting the signals through wavelet transform and fast Fourier transform （FFT）. Since the converted chatter sig-nals exhibit different characteristics from the normal signals, through defining the characteristic val-ues, such as root-mean-square value, max value, and ratio of peak value to root-mean-square value, etc, a diagnosis reference library that contains the distribution of these characteristic values is built for diagnosis. When a diagnosis is executing, the characteristic value of the measured signals is con-trasted with the diagnosis reference. The approach index which shows the possibility of occurrence of milling chatter will, then, be calculated through the diagnosis system. Cutting experiments are con-ducted to verify the proposed diagnosis system. The results show the success of early chatter detecting for the system.
文摘A new method is proposed to suppress chatter, in which the ultrasonic elliptical vibration is added on the cutting tool edge. It results in the fact that the rake face of tool is separated from the chip and the direction of the frictional force between the rake face and the chip is reversed in each cycle of elliptical vibration cutting. The experimental investigations show that the chatter can be suppressed effectively by adding ultrasonic elliptical vibration on the cutting tool edge. In order to make clear the reason of chatter suppression, the mechanism of chatter suppression is analyzed theoretically from the viewpoint of energy.
