Casting experiments and macro-micro numerical simulations were conducted to examine the microstructure characteristics of K439B nickel-based superalloy casting with varying cross-sections during the gravity investment...Casting experiments and macro-micro numerical simulations were conducted to examine the microstructure characteristics of K439B nickel-based superalloy casting with varying cross-sections during the gravity investment casting process.Firstly,microstructure analysis was conducted on the casting using scanning electron microscopy(SEM)and electron backscatter diffraction(EBSD).Subsequently,calculation of the phase diagram and differential scanning calorimetry(DSC)tests were conducted to determine the macro-micro simulation parameters of the K439B alloy,and the cellular automaton finite element(CAFE)method was employed to develop macro-micro modeling of K439B nickel-based superalloy casting with varying cross-sections.The experimental results revealed that the ratio of the average grain area increased from the edge to the center of the sections as the ratio of the cross-sectional area increased.The simulation results indicated that the average grain area increased from 0.885 to 0.956 mm^(2)as the ratio of the cross-sections increased from 6꞉1 to 12꞉1.The experiment and simulation results showed that the grain size became more heterogeneous and the grain shape became more irregular with an increase in the ratio of the cross-sectional area of the casting.CAFE modeling was an effective method to simulate the microstructure evolution of the K439B alloy and ensure the accuracy of the simulation.展开更多
In this study,K and L shell photoeffect cross-sections were measured for the elements in the range of 50≤Z≤65at 59.5keV.These photoeffect cross-sections were measured by using the experimentalσKαproduction cross-s...In this study,K and L shell photoeffect cross-sections were measured for the elements in the range of 50≤Z≤65at 59.5keV.These photoeffect cross-sections were measured by using the experimentalσKαproduction cross-section values measured in this paper and two different K shell fluorescence yield values in the literature.The results were compared with the calculated theoretical values.The values were plotted versus atomic number.展开更多
The aim of this study was to compare mandibular form （i.e., size and shape） between patients with agenesis of the lower second premolar （P2） and a control group with no agenesis. Three hypotheses were tested： （H...The aim of this study was to compare mandibular form （i.e., size and shape） between patients with agenesis of the lower second premolar （P2） and a control group with no agenesis. Three hypotheses were tested： （H1） agenesis causes a change in mandibular morphology because of inadequate alveolar ridge development in the area of the missing tooth （mandibular plasticity）; （H2） agenesis is caused by spatial limitations within the mandible （dental plasticity）; and （H3） common genetic/ epigenetic factors cause agenesis and affect mandibular form （pleiotropy）. A geometric morphometric analysis was applied to cross-sectional images of computed tomography （CT） scans of three matched groups （n= 50 each）： （1） regularly erupted P2; （2） agenesis of P2 and the primary second molar in situ; and （3） agenesis of P2 and the primary second molar missing for 〉3 months. Cross-sections of the three areas of interest （first premolar, P2, first molar） were digitized with 23 landmarks and superimposed by a generalized Procrustes analysis. On average, the mandibular cross-sections were narrower and shorter in patients with P2 agenesis compared with that in the control group. Both agenesis groups featured a pronounced submandibular fossa. These differences extended at least one tooth beyond the agenesis-affected region. Taken together with the large interindividual variation that resulted in massively overlapping group distributions, these findings support genetic and/or epigenetic pleiotropy （H3） as the most likely origin of the observed covariation between mandibular form and odontogenesis. Clinically, reduced dimensions and greater variability of mandibular form, as well as a pronounced submandibular fossa, should be expected during the treatment planning of patients with P2 agenesis.展开更多
Based on the unified Hauser–Feshbach and exciton model,which can describe the particle emission processes between discrete energy levels with energy,angular momentum,and parity conservations,a statistical theory of l...Based on the unified Hauser–Feshbach and exciton model,which can describe the particle emission processes between discrete energy levels with energy,angular momentum,and parity conservations,a statistical theory of light nucleus reaction(STLN)is developed to calculate the double-differential cross-sections of the outgoing neutron and light charged particles for the proton-induced^(6) Li reaction.A significant difference is observed between the p+^(6) Li and p+^(7) Li reactions owing to the discrepancies in the energy-level structures of the targets.The reaction channels,including sequential and simultaneous emission processes,are analyzed in detail.Taking the double-differential cross-sections of the outgoing proton as an example,the influence of contaminations(such as^(1) H,^(7)Li,^(12)C,and^(16)O)on the target is identified in terms of the kinetic energy of the first emitted particles.The optical potential parameters of the proton are obtained by fitting the elastic scattering differential cross-sections.The calculated total double-differential cross-sections of the outgoing proton and deuteron at E_(p)=14 MeV agree well with the experimental data for different outgoing angles.Simultaneously,the mixed double differential cross-sections of^(3) He andαare in good agreement with the measurements.The agreement between the measured data and calculated results indicates that the two-body and three-body breakup reactions need to be considered,and the pre-equilibrium reaction mechanism dominates the reaction processes.Based on the STLN model,a PLUNF code for the p+^(6) Li reaction is developed to obtain an ENDF-6-formatted file of the double-differential cross-sections of the nucleon and light composite charged particles.展开更多
Viewing gravitational energy-momentum PG<sup style='margin-left:-7px;'>μ as equal by observation, but different in essence from inertial energy-momentum PI<sup style='margin-left:-7px;'>μ...Viewing gravitational energy-momentum PG<sup style='margin-left:-7px;'>μ as equal by observation, but different in essence from inertial energy-momentum PI<sup style='margin-left:-7px;'>μ naturally leads to the gauge theory of volume-preserving diffeomorphisms of a four-dimensional inner space. To analyse scattering in this theory, the gauge field is coupled to two Dirac fields with different masses. Based on a generalized LSZ reduction formula the S-matrix element for scattering of two Dirac particles in the gravitational limit and the corresponding scattering cross-section are calculated to leading order in perturbation theory. Taking the non-relativistic limit for one of the initial particles in the rest frame of the other the Rutherford-like cross-section of a non-relativistic particle scattering off an infinitely heavy scatterer calculated quantum mechanically in Newtonian gravity is recovered. This provides a non-trivial test of the gauge field theory of volume-preserving diffeomorphisms as a quantum theory of gravity.展开更多
Triple differential cross sections (TDCS) are estimated for the ionization of metastable 3d-state hydrogen atoms by electron at 250 eV for various kinematic conditions pursuing a multiple scattering theory. The presen...Triple differential cross sections (TDCS) are estimated for the ionization of metastable 3d-state hydrogen atoms by electron at 250 eV for various kinematic conditions pursuing a multiple scattering theory. The present new results are compared with the theoretical results of hydrogenic different metastable states as well as the hydrogenic ground state experimental data. Obtained new finding results are in good qualitative agreement with those of compared theories. The present results give an immense opportunity for experimental trial in the field of ionization problems.展开更多
A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigate...A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigated by the generalized differential quadrature rule （GDQR） method. The GDQR method is also used to calculate the forced vibration response of the beam and voltage of each piezoelectric layer when the beam is subject to a sinusoidal base excitation. Results obtained from the analytical method are compared with those obtained from the finite element simulation with ANSYS, and good agreement is found. The voltage output of this periodic beam over its first band gap is calculated and compared with the voltage output of the uniform piezoelectric beam. It is concluded that this periodic beam has three advantages over the uniform piezoelectric beam, i.e., generating more voltage outputs over a wide frequency range, absorbing vibration, and being less weight.展开更多
Tunnel deformation monitoring is a crucial task to evaluate tunnel stability during the metro operation period.Terrestrial Laser Scanning(TLS)can collect high density and high accuracy point cloud data in a few minute...Tunnel deformation monitoring is a crucial task to evaluate tunnel stability during the metro operation period.Terrestrial Laser Scanning(TLS)can collect high density and high accuracy point cloud data in a few minutes as an innovation technique,which provides promising applications in tunnel deformation monitoring.Here,an efficient method for extracting tunnel cross-sections and convergence analysis using dense TLS point cloud data is proposed.First,the tunnel orientation is determined using principal component analysis(PCA)in the Euclidean plane.Two control points are introduced to detect and remove the unsuitable points by using point cloud division and then the ground points are removed by defining an elevation value width of 0.5 m.Next,a z-score method is introduced to detect and remove the outlies.Because the tunnel cross-section’s standard shape is round,the circle fitting is implemented using the least-squares method.Afterward,the convergence analysis is made at the angles of 0°,30°and 150°.The proposed approach’s feasibility is tested on a TLS point cloud of a Nanjing subway tunnel acquired using a FARO X330 laser scanner.The results indicate that the proposed methodology achieves an overall accuracy of 1.34 mm,which is also in agreement with the measurements acquired by a total station instrument.The proposed methodology provides new insights and references for the applications of TLS in tunnel deformation monitoring,which can also be extended to other engineering applications.展开更多
An alternative expression for photoionization cross-section of atoms or molecules and a dielectric influence function （DIF） in a high-density system proposed recently are used to study the photoionization cross-sect...An alternative expression for photoionization cross-section of atoms or molecules and a dielectric influence function （DIF） in a high-density system proposed recently are used to study the photoionization cross-sections of solid silver. It is suggested that a density turning point （DTP） of a photoionized system may be viewed as the critical point where the photoionization properties of atoms in a real system may have a notable change. The results show that the present theoretical photoionization cross-sections are in good agreement with the experimental results of a silver crystal both in structure and in magnitude.展开更多
Large Eddy Simulation(LES)has been employed for the investigation of supersonic flow characteristics in five ducts with varying cross-sectional geometries.The numerical results reveal that flow channel configurations ...Large Eddy Simulation(LES)has been employed for the investigation of supersonic flow characteristics in five ducts with varying cross-sectional geometries.The numerical results reveal that flow channel configurations exert a considerable influence on the mainstream flow and the near-wall flow behavior.In contrast to straight ducts,square-to-circular and rectangular-to-circular ducts exhibit thicker boundary layers and a greater presence of vortex structures.Given the same inlet area,rectangular-to-circular ducts lead to higher flow drag force and total pressure loss than square-to-circular ducts.Characterized by the substantial flow separation and shock waves,the"S-shaped duct shows significant vertically-asymmetric characteristics.展开更多
A new method for reconstructing a 3-dimensional object from serial cross-sectionsis presented in this paper.The method is based on the principle of sampling and considersevery point in cross-sections as a sampling poi...A new method for reconstructing a 3-dimensional object from serial cross-sectionsis presented in this paper.The method is based on the principle of sampling and considersevery point in cross-sections as a sampling point and performs the interpolating of nonlinearfunction with these sampling points.Compared with other methods,this method has manyadvantages such as higher precision and fewer requested known sampling points.The result ofreconstruction with this method is an“entity”which involves the exterior shape and interiorconstruction information of the object simultaneously.展开更多
Interest has recently emerged in potential applications of(n,2n)reactions of unstable nuclei.Challenges have arisen because of the scarcity of experimental cross-sectional data.This study aims to predict the(n,2n)reac...Interest has recently emerged in potential applications of(n,2n)reactions of unstable nuclei.Challenges have arisen because of the scarcity of experimental cross-sectional data.This study aims to predict the(n,2n)reaction cross-section of long-lived fission products based on a tensor model.This tensor model is an extension of the collaborative filtering algorithm used for nuclear data.It is based on tensor decomposition and completion to predict(n,2n)reaction cross-sections;the corresponding EXFOR data are applied as training data.The reliability of the proposed tensor model was validated by comparing the calculations with data from EXFOR and different databases.Predictions were made for long-lived fission products such as^(60)Co,^(79)Se,^(93)Zr,^(107)P,^(126)Sn,and^(137)Cs,which provide a predicted energy range to effectively transmute long-lived fission products into shorter-lived or less radioactive isotopes.This method could be a powerful tool for completing(n,2n)reaction cross-sectional data and shows the possibility of selective transmutation of nuclear waste.展开更多
Objective:To assess prenatal Bisphenol A(BPA)exposure levels and explore their preliminary associations with maternal and fetal characteristics in a population from Northeastern Yunnan.Methods:A cross-sectional analys...Objective:To assess prenatal Bisphenol A(BPA)exposure levels and explore their preliminary associations with maternal and fetal characteristics in a population from Northeastern Yunnan.Methods:A cross-sectional analysis was performed using data and urine samples from 70 pregnant women in their third trimester recruited at Qujing Central Hospital.Urinary BPA was measured by HPLC-MS/MS.Participants were stratified into high and low BPA exposure groups based on the median concentration.Results:BPA was detected in all samples(100%)with a median concentration of 2.41μg/L(IQR:0.68-4.96).The high BPA exposure group(≥2.41μg/L)had a significantly higher proportion of gestational diabetes mellitus(GDM)(42.9%vs.17.1%,p=0.021)and a lower median fetal birth weight(3250 g vs.3450 g,p=0.048)compared to the low exposure group.Conclusion:This pilot study reveals ubiquitous BPA exposure in pregnant women from Northeastern Yunnan.The observed preliminary associations with GDM and reduced fetal birth weight warrant further investigation in larger,longitudinal studies.展开更多
Ultra-high-strength aluminumalloy profile is an ideal choice for aerospace structuralmaterials due to its excellent specific strength and corrosion resistance.However,issues such as uneven metal flow,stress concentrat...Ultra-high-strength aluminumalloy profile is an ideal choice for aerospace structuralmaterials due to its excellent specific strength and corrosion resistance.However,issues such as uneven metal flow,stress concentration,and forming defects are prone to occur during their extrusion.This study focuses on an Al-Zn-Mg-Cu ultra-high-strength aluminum alloy profile with a double-U,multi-cavity thin-walled structure.Firstly,hot compression experiments were conducted at temperatures of 350○C,400○C,and 450○C,with strain rates of 0.01 and 1.0 s^(−1),to investigate the plastic deformation behavior of the material.Subsequently,a 3D coupled thermo-mechanical extrusion simulation model was established using Deform-3D to systematically analyze the influence of die structure and process parameters on metal flow velocity,effective stress/strain,and temperature distribution.The simulation revealed significant velocity differences,stress concentration,and uneven temperature distribution.Key parameters,including mesh density,extrusion ratio,die fillet,and bearing length,were optimized through full-factorial experiments.This optimization,combined with a stepped flow-guiding die design,effectively improved the metal flow pattern during extrusion.Trial production based on both the initial and optimized parameters were carried out.A comparative analysis demonstrates that the optimized scheme results in a final profile whose cross-section matches the target design closely,with complete filling of complex features and no obvious forming defects.This research provides a valuable reference for the extrusion process optimization and die design of complex-section profiles made from ultra-high-strength aluminum alloys.展开更多
Objective This study aimed to determine the temporal trends in sleep duration among Chinese adults.Methods In this series of repeated nationally representative cross-sectional surveys(China Chronic Disease and Risk Fa...Objective This study aimed to determine the temporal trends in sleep duration among Chinese adults.Methods In this series of repeated nationally representative cross-sectional surveys(China Chronic Disease and Risk Factors Surveillance)conducted between 2010 and 2018,a total of 645,420 adult participants(97,741 in 2010;175,749 in 2013;187,777 in 2015;and 184,153 in 2018)were included in the trend analysis.Linear and logistic regression models were utilized to assess trends in sleep duration.Results In 2018,the estimated overall mean sleep duration among the Chinese adult population was7.58(SD,1.45)hours per day,with no significant trend from 2010.A significant increase in short sleep duration(≤6 hours)was observed in the total population,from 15.3%(95%CI:14.1%–16.5%)in 2010 to18.5%(95%CI:17.7%–19.3%)in 2018(P<0.001).Similarly,the trend in long sleep duration(>9 hours)was also significant,increasing in weighted prevalence from 7.2%(95%CI:6.3%–8.1%)in 2010 to 9.0%(95%CI:8.2%–9.9%)in 2018(P<0.001).Conclusion The prevalence of both short and long sleep durations significantly increased among Chinese adults from 2010 to 2018,highlighting the urgency of health initiatives to promote optimal sleep duration in China.展开更多
We investigated the impact of convexity and isoperimetric deficits on the accuracy of sectional area estimates of tree stems using traditional methods(caliper,tape,formulas based on stem diameter and circumference).In...We investigated the impact of convexity and isoperimetric deficits on the accuracy of sectional area estimates of tree stems using traditional methods(caliper,tape,formulas based on stem diameter and circumference).In two complementary experiments,the use of photographs to estimate cross-sectional areas was first validated,then the use of a caliper and diameter tape was computer-simulated.The results indicated that the photographic method offers high precision,with mean relative errors below 0.1%,minimal deviation,and no significant bias,and the traditional methods led to substantial and systematic errors,with deviations from circularity and convexity significantly increasing the errors in area estimation.展开更多
Over the past decades, low-energy electron accelerators have been used worldwide for surface curing and sterilization. The beam nonuniformity is an important parameter of the low-energy electron beam with large cross-...Over the past decades, low-energy electron accelerators have been used worldwide for surface curing and sterilization. The beam nonuniformity is an important parameter of the low-energy electron beam with large cross-sections. A simple and accurate measurement system of nonuniformity for the low-energy electron beam with large cross-sections was developed. The main concept consists in the measurement of nonuniformity, which is realized by using a linear actuator to drive two scanning wires through the beam's cross-sections at a fixed speed. The beam distribution can be obtained by sending/collecting the current signals to/from the Data Acquisition (DAQ) software on a laptop by a USB DAQ card. This device is very convenient for the performance testing of a new accelerator at the manufacturer's site. The distribution of the homemade low voltage electron accelerator EBS-300-50 was measured and evaluated.展开更多
With the development of science and technology the entire Earth,together with all of its phenomena,is gradually becoming an object of computer digitisation.For several years,this process has also affected water compon...With the development of science and technology the entire Earth,together with all of its phenomena,is gradually becoming an object of computer digitisation.For several years,this process has also affected water components,which are essential for the development of humans and economies on Earth.Therefore,monitoring of its resources and movement across the Earth’s surface is the main object of investigation of several research institutions.In recent years,hydraulic modelling has experienced significant development that meets water and computer connection conditions.This study consequently dealt with hydraulic modelling and uncertainties in the data that may affect the resulting flood zone.We analysed the effect of cross-sections generated and the subsequent inundation areas in Digital Elevation Models of different resolutions.The basic DEM was constructed from data obtained by the LIDAR method.Hydraulic results were obtained using a one-dimensional(1-D)model,HEC-RAS,and its extension,HEC-GeoRAS.The Olsˇe and Stona´vka river junction,located in the northeast region of the Czech Republic,was selected for investigation.The resolutions selected for the study to generate cross-sections and the subsequent inundation areas were 1 m,5 m and 10 m.The resulting cross-sections were confronted with the actual surveyed cross-sections.展开更多
The reaction cross-sections of^(238)U(n,γ)^(239)U have been experimentally determined at neutron energies of6.117±0.119 MeV,4.626±0.086 MeV,and 3.622±0.348 MeV employing the relative activation approac...The reaction cross-sections of^(238)U(n,γ)^(239)U have been experimentally determined at neutron energies of6.117±0.119 MeV,4.626±0.086 MeV,and 3.622±0.348 MeV employing the relative activation approach along with the off-line γ-ray spectroscopy method.The D(d,n)3He reaction was utilized to obtain monoenergetic neutrons of the required energy,and the^(197)Au(n,γ)^(198)Au reaction cross-sections were adopted as the referential standard to ascertain the neutron capture cross-sections of^(238)U.Furthermore,the effects of low-energy scattered neutrons,neutron fluence fluctuations,counting of geometric corrections when measuring γ-rays,and neutron and γ-ray self-absorption caused by the sample thickness have been considered and revised in the present work.For a comparison with experimental results,the cross-sections of the^(238)U(n,γ)^(239)U reaction were calculated theoretically with the original parametric TALYS-1.9 program.The experimental measurements were in contrast to previous experimental re sults and the evaluation data available for ROSFOND-2010,CENDL-3.2 and ENDF/B-VIII.0.展开更多
The Bayesian neural network(BNN)method is proposed to predict the isotopic cross-sections in proton induced spallation reactions.Learning from more than 4000 data sets of isotopic cross-sections from 19 experimental m...The Bayesian neural network(BNN)method is proposed to predict the isotopic cross-sections in proton induced spallation reactions.Learning from more than 4000 data sets of isotopic cross-sections from 19 experimental measurements and 5 theoretical predictions with the SPACS parametrization,in which the mass of the spallation system ranges from 36 to 238,and the incident energy from 200 MeV/u to 1500 MeV/u,it is demonstrated that the BNN method can provide good predictions of the residue fragment cross-sections in spallation reactions.展开更多
基金supported by the National Science and Technology Major Project of China(No.J2019-VI-0004-0117)。
文摘Casting experiments and macro-micro numerical simulations were conducted to examine the microstructure characteristics of K439B nickel-based superalloy casting with varying cross-sections during the gravity investment casting process.Firstly,microstructure analysis was conducted on the casting using scanning electron microscopy(SEM)and electron backscatter diffraction(EBSD).Subsequently,calculation of the phase diagram and differential scanning calorimetry(DSC)tests were conducted to determine the macro-micro simulation parameters of the K439B alloy,and the cellular automaton finite element(CAFE)method was employed to develop macro-micro modeling of K439B nickel-based superalloy casting with varying cross-sections.The experimental results revealed that the ratio of the average grain area increased from the edge to the center of the sections as the ratio of the cross-sectional area increased.The simulation results indicated that the average grain area increased from 0.885 to 0.956 mm^(2)as the ratio of the cross-sections increased from 6꞉1 to 12꞉1.The experiment and simulation results showed that the grain size became more heterogeneous and the grain shape became more irregular with an increase in the ratio of the cross-sectional area of the casting.CAFE modeling was an effective method to simulate the microstructure evolution of the K439B alloy and ensure the accuracy of the simulation.
文摘In this study,K and L shell photoeffect cross-sections were measured for the elements in the range of 50≤Z≤65at 59.5keV.These photoeffect cross-sections were measured by using the experimentalσKαproduction cross-section values measured in this paper and two different K shell fluorescence yield values in the literature.The results were compared with the calculated theoretical values.The values were plotted versus atomic number.
文摘The aim of this study was to compare mandibular form （i.e., size and shape） between patients with agenesis of the lower second premolar （P2） and a control group with no agenesis. Three hypotheses were tested： （H1） agenesis causes a change in mandibular morphology because of inadequate alveolar ridge development in the area of the missing tooth （mandibular plasticity）; （H2） agenesis is caused by spatial limitations within the mandible （dental plasticity）; and （H3） common genetic/ epigenetic factors cause agenesis and affect mandibular form （pleiotropy）. A geometric morphometric analysis was applied to cross-sectional images of computed tomography （CT） scans of three matched groups （n= 50 each）： （1） regularly erupted P2; （2） agenesis of P2 and the primary second molar in situ; and （3） agenesis of P2 and the primary second molar missing for 〉3 months. Cross-sections of the three areas of interest （first premolar, P2, first molar） were digitized with 23 landmarks and superimposed by a generalized Procrustes analysis. On average, the mandibular cross-sections were narrower and shorter in patients with P2 agenesis compared with that in the control group. Both agenesis groups featured a pronounced submandibular fossa. These differences extended at least one tooth beyond the agenesis-affected region. Taken together with the large interindividual variation that resulted in massively overlapping group distributions, these findings support genetic and/or epigenetic pleiotropy （H3） as the most likely origin of the observed covariation between mandibular form and odontogenesis. Clinically, reduced dimensions and greater variability of mandibular form, as well as a pronounced submandibular fossa, should be expected during the treatment planning of patients with P2 agenesis.
基金supported by the National Natural Science Foundation of China(No.12065003)the Guangxi Key R&D Project(2023AB07029)+1 种基金the Scientific Research and Technology Development Project of Guilin(20210104-2)the Central Government Guides Local Scientific and Technological Development Funds of China(Guike ZY22096024)。
文摘Based on the unified Hauser–Feshbach and exciton model,which can describe the particle emission processes between discrete energy levels with energy,angular momentum,and parity conservations,a statistical theory of light nucleus reaction(STLN)is developed to calculate the double-differential cross-sections of the outgoing neutron and light charged particles for the proton-induced^(6) Li reaction.A significant difference is observed between the p+^(6) Li and p+^(7) Li reactions owing to the discrepancies in the energy-level structures of the targets.The reaction channels,including sequential and simultaneous emission processes,are analyzed in detail.Taking the double-differential cross-sections of the outgoing proton as an example,the influence of contaminations(such as^(1) H,^(7)Li,^(12)C,and^(16)O)on the target is identified in terms of the kinetic energy of the first emitted particles.The optical potential parameters of the proton are obtained by fitting the elastic scattering differential cross-sections.The calculated total double-differential cross-sections of the outgoing proton and deuteron at E_(p)=14 MeV agree well with the experimental data for different outgoing angles.Simultaneously,the mixed double differential cross-sections of^(3) He andαare in good agreement with the measurements.The agreement between the measured data and calculated results indicates that the two-body and three-body breakup reactions need to be considered,and the pre-equilibrium reaction mechanism dominates the reaction processes.Based on the STLN model,a PLUNF code for the p+^(6) Li reaction is developed to obtain an ENDF-6-formatted file of the double-differential cross-sections of the nucleon and light composite charged particles.
文摘Viewing gravitational energy-momentum PG<sup style='margin-left:-7px;'>μ as equal by observation, but different in essence from inertial energy-momentum PI<sup style='margin-left:-7px;'>μ naturally leads to the gauge theory of volume-preserving diffeomorphisms of a four-dimensional inner space. To analyse scattering in this theory, the gauge field is coupled to two Dirac fields with different masses. Based on a generalized LSZ reduction formula the S-matrix element for scattering of two Dirac particles in the gravitational limit and the corresponding scattering cross-section are calculated to leading order in perturbation theory. Taking the non-relativistic limit for one of the initial particles in the rest frame of the other the Rutherford-like cross-section of a non-relativistic particle scattering off an infinitely heavy scatterer calculated quantum mechanically in Newtonian gravity is recovered. This provides a non-trivial test of the gauge field theory of volume-preserving diffeomorphisms as a quantum theory of gravity.
文摘Triple differential cross sections (TDCS) are estimated for the ionization of metastable 3d-state hydrogen atoms by electron at 250 eV for various kinematic conditions pursuing a multiple scattering theory. The present new results are compared with the theoretical results of hydrogenic different metastable states as well as the hydrogenic ground state experimental data. Obtained new finding results are in good qualitative agreement with those of compared theories. The present results give an immense opportunity for experimental trial in the field of ionization problems.
文摘A bimorph piezoelectric beam with periodically variable cross-sections is used for the vibration energy harvesting. The effects of two geometrical parameters on the first band gap of this periodic beam are investigated by the generalized differential quadrature rule （GDQR） method. The GDQR method is also used to calculate the forced vibration response of the beam and voltage of each piezoelectric layer when the beam is subject to a sinusoidal base excitation. Results obtained from the analytical method are compared with those obtained from the finite element simulation with ANSYS, and good agreement is found. The voltage output of this periodic beam over its first band gap is calculated and compared with the voltage output of the uniform piezoelectric beam. It is concluded that this periodic beam has three advantages over the uniform piezoelectric beam, i.e., generating more voltage outputs over a wide frequency range, absorbing vibration, and being less weight.
基金National Natural Science Foundation of China(No.41801379)Fundamental Research Funds for the Central Universities(No.2019B08414)National Key R&D Program of China(No.2016YFC0401801)。
文摘Tunnel deformation monitoring is a crucial task to evaluate tunnel stability during the metro operation period.Terrestrial Laser Scanning(TLS)can collect high density and high accuracy point cloud data in a few minutes as an innovation technique,which provides promising applications in tunnel deformation monitoring.Here,an efficient method for extracting tunnel cross-sections and convergence analysis using dense TLS point cloud data is proposed.First,the tunnel orientation is determined using principal component analysis(PCA)in the Euclidean plane.Two control points are introduced to detect and remove the unsuitable points by using point cloud division and then the ground points are removed by defining an elevation value width of 0.5 m.Next,a z-score method is introduced to detect and remove the outlies.Because the tunnel cross-section’s standard shape is round,the circle fitting is implemented using the least-squares method.Afterward,the convergence analysis is made at the angles of 0°,30°and 150°.The proposed approach’s feasibility is tested on a TLS point cloud of a Nanjing subway tunnel acquired using a FARO X330 laser scanner.The results indicate that the proposed methodology achieves an overall accuracy of 1.34 mm,which is also in agreement with the measurements acquired by a total station instrument.The proposed methodology provides new insights and references for the applications of TLS in tunnel deformation monitoring,which can also be extended to other engineering applications.
基金Project supported by the National Natural Science Foundation of China （Grant No 10474068） and the Natural Science Foundation of Yantai Normal University （Grant No 22270301）.
文摘An alternative expression for photoionization cross-section of atoms or molecules and a dielectric influence function （DIF） in a high-density system proposed recently are used to study the photoionization cross-sections of solid silver. It is suggested that a density turning point （DTP） of a photoionized system may be viewed as the critical point where the photoionization properties of atoms in a real system may have a notable change. The results show that the present theoretical photoionization cross-sections are in good agreement with the experimental results of a silver crystal both in structure and in magnitude.
基金the National Natural Science Foundation of China(Grant Nos.92252206,12102471 and 11925207)。
文摘Large Eddy Simulation(LES)has been employed for the investigation of supersonic flow characteristics in five ducts with varying cross-sectional geometries.The numerical results reveal that flow channel configurations exert a considerable influence on the mainstream flow and the near-wall flow behavior.In contrast to straight ducts,square-to-circular and rectangular-to-circular ducts exhibit thicker boundary layers and a greater presence of vortex structures.Given the same inlet area,rectangular-to-circular ducts lead to higher flow drag force and total pressure loss than square-to-circular ducts.Characterized by the substantial flow separation and shock waves,the"S-shaped duct shows significant vertically-asymmetric characteristics.
文摘A new method for reconstructing a 3-dimensional object from serial cross-sectionsis presented in this paper.The method is based on the principle of sampling and considersevery point in cross-sections as a sampling point and performs the interpolating of nonlinearfunction with these sampling points.Compared with other methods,this method has manyadvantages such as higher precision and fewer requested known sampling points.The result ofreconstruction with this method is an“entity”which involves the exterior shape and interiorconstruction information of the object simultaneously.
基金supported by the Key Laboratory of Nuclear Data foundation(No.JCKY2022201C157)。
文摘Interest has recently emerged in potential applications of(n,2n)reactions of unstable nuclei.Challenges have arisen because of the scarcity of experimental cross-sectional data.This study aims to predict the(n,2n)reaction cross-section of long-lived fission products based on a tensor model.This tensor model is an extension of the collaborative filtering algorithm used for nuclear data.It is based on tensor decomposition and completion to predict(n,2n)reaction cross-sections;the corresponding EXFOR data are applied as training data.The reliability of the proposed tensor model was validated by comparing the calculations with data from EXFOR and different databases.Predictions were made for long-lived fission products such as^(60)Co,^(79)Se,^(93)Zr,^(107)P,^(126)Sn,and^(137)Cs,which provide a predicted energy range to effectively transmute long-lived fission products into shorter-lived or less radioactive isotopes.This method could be a powerful tool for completing(n,2n)reaction cross-sectional data and shows the possibility of selective transmutation of nuclear waste.
文摘Objective:To assess prenatal Bisphenol A(BPA)exposure levels and explore their preliminary associations with maternal and fetal characteristics in a population from Northeastern Yunnan.Methods:A cross-sectional analysis was performed using data and urine samples from 70 pregnant women in their third trimester recruited at Qujing Central Hospital.Urinary BPA was measured by HPLC-MS/MS.Participants were stratified into high and low BPA exposure groups based on the median concentration.Results:BPA was detected in all samples(100%)with a median concentration of 2.41μg/L(IQR:0.68-4.96).The high BPA exposure group(≥2.41μg/L)had a significantly higher proportion of gestational diabetes mellitus(GDM)(42.9%vs.17.1%,p=0.021)and a lower median fetal birth weight(3250 g vs.3450 g,p=0.048)compared to the low exposure group.Conclusion:This pilot study reveals ubiquitous BPA exposure in pregnant women from Northeastern Yunnan.The observed preliminary associations with GDM and reduced fetal birth weight warrant further investigation in larger,longitudinal studies.
基金supported by the National Key Research and Development Program of China(Grant No.2023YFB3710805).
文摘Ultra-high-strength aluminumalloy profile is an ideal choice for aerospace structuralmaterials due to its excellent specific strength and corrosion resistance.However,issues such as uneven metal flow,stress concentration,and forming defects are prone to occur during their extrusion.This study focuses on an Al-Zn-Mg-Cu ultra-high-strength aluminum alloy profile with a double-U,multi-cavity thin-walled structure.Firstly,hot compression experiments were conducted at temperatures of 350○C,400○C,and 450○C,with strain rates of 0.01 and 1.0 s^(−1),to investigate the plastic deformation behavior of the material.Subsequently,a 3D coupled thermo-mechanical extrusion simulation model was established using Deform-3D to systematically analyze the influence of die structure and process parameters on metal flow velocity,effective stress/strain,and temperature distribution.The simulation revealed significant velocity differences,stress concentration,and uneven temperature distribution.Key parameters,including mesh density,extrusion ratio,die fillet,and bearing length,were optimized through full-factorial experiments.This optimization,combined with a stepped flow-guiding die design,effectively improved the metal flow pattern during extrusion.Trial production based on both the initial and optimized parameters were carried out.A comparative analysis demonstrates that the optimized scheme results in a final profile whose cross-section matches the target design closely,with complete filling of complex features and no obvious forming defects.This research provides a valuable reference for the extrusion process optimization and die design of complex-section profiles made from ultra-high-strength aluminum alloys.
基金supported by the National Natural Science Foundation of China(82341245,82371491)the Chinese Central Government(Key Project of Public Health Program)the National Key Research and Development Program of China(2018YFC1311706,2018YFC1311702)。
文摘Objective This study aimed to determine the temporal trends in sleep duration among Chinese adults.Methods In this series of repeated nationally representative cross-sectional surveys(China Chronic Disease and Risk Factors Surveillance)conducted between 2010 and 2018,a total of 645,420 adult participants(97,741 in 2010;175,749 in 2013;187,777 in 2015;and 184,153 in 2018)were included in the trend analysis.Linear and logistic regression models were utilized to assess trends in sleep duration.Results In 2018,the estimated overall mean sleep duration among the Chinese adult population was7.58(SD,1.45)hours per day,with no significant trend from 2010.A significant increase in short sleep duration(≤6 hours)was observed in the total population,from 15.3%(95%CI:14.1%–16.5%)in 2010 to18.5%(95%CI:17.7%–19.3%)in 2018(P<0.001).Similarly,the trend in long sleep duration(>9 hours)was also significant,increasing in weighted prevalence from 7.2%(95%CI:6.3%–8.1%)in 2010 to 9.0%(95%CI:8.2%–9.9%)in 2018(P<0.001).Conclusion The prevalence of both short and long sleep durations significantly increased among Chinese adults from 2010 to 2018,highlighting the urgency of health initiatives to promote optimal sleep duration in China.
文摘We investigated the impact of convexity and isoperimetric deficits on the accuracy of sectional area estimates of tree stems using traditional methods(caliper,tape,formulas based on stem diameter and circumference).In two complementary experiments,the use of photographs to estimate cross-sectional areas was first validated,then the use of a caliper and diameter tape was computer-simulated.The results indicated that the photographic method offers high precision,with mean relative errors below 0.1%,minimal deviation,and no significant bias,and the traditional methods led to substantial and systematic errors,with deviations from circularity and convexity significantly increasing the errors in area estimation.
文摘Over the past decades, low-energy electron accelerators have been used worldwide for surface curing and sterilization. The beam nonuniformity is an important parameter of the low-energy electron beam with large cross-sections. A simple and accurate measurement system of nonuniformity for the low-energy electron beam with large cross-sections was developed. The main concept consists in the measurement of nonuniformity, which is realized by using a linear actuator to drive two scanning wires through the beam's cross-sections at a fixed speed. The beam distribution can be obtained by sending/collecting the current signals to/from the Data Acquisition (DAQ) software on a laptop by a USB DAQ card. This device is very convenient for the performance testing of a new accelerator at the manufacturer's site. The distribution of the homemade low voltage electron accelerator EBS-300-50 was measured and evaluated.
文摘With the development of science and technology the entire Earth,together with all of its phenomena,is gradually becoming an object of computer digitisation.For several years,this process has also affected water components,which are essential for the development of humans and economies on Earth.Therefore,monitoring of its resources and movement across the Earth’s surface is the main object of investigation of several research institutions.In recent years,hydraulic modelling has experienced significant development that meets water and computer connection conditions.This study consequently dealt with hydraulic modelling and uncertainties in the data that may affect the resulting flood zone.We analysed the effect of cross-sections generated and the subsequent inundation areas in Digital Elevation Models of different resolutions.The basic DEM was constructed from data obtained by the LIDAR method.Hydraulic results were obtained using a one-dimensional(1-D)model,HEC-RAS,and its extension,HEC-GeoRAS.The Olsˇe and Stona´vka river junction,located in the northeast region of the Czech Republic,was selected for investigation.The resolutions selected for the study to generate cross-sections and the subsequent inundation areas were 1 m,5 m and 10 m.The resulting cross-sections were confronted with the actual surveyed cross-sections.
基金Supported by the Key Laboratory of Nuclear Data foundation (6142A08200104)。
文摘The reaction cross-sections of^(238)U(n,γ)^(239)U have been experimentally determined at neutron energies of6.117±0.119 MeV,4.626±0.086 MeV,and 3.622±0.348 MeV employing the relative activation approach along with the off-line γ-ray spectroscopy method.The D(d,n)3He reaction was utilized to obtain monoenergetic neutrons of the required energy,and the^(197)Au(n,γ)^(198)Au reaction cross-sections were adopted as the referential standard to ascertain the neutron capture cross-sections of^(238)U.Furthermore,the effects of low-energy scattered neutrons,neutron fluence fluctuations,counting of geometric corrections when measuring γ-rays,and neutron and γ-ray self-absorption caused by the sample thickness have been considered and revised in the present work.For a comparison with experimental results,the cross-sections of the^(238)U(n,γ)^(239)U reaction were calculated theoretically with the original parametric TALYS-1.9 program.The experimental measurements were in contrast to previous experimental re sults and the evaluation data available for ROSFOND-2010,CENDL-3.2 and ENDF/B-VIII.0.
基金Supported by the National Natural Science Foundation of China(11975091,U1732135,11875070)Natural Science Foundation of Henan Province(162300410179)supported by the US Department of Energy(DE-FG02-93ER40773)
文摘The Bayesian neural network(BNN)method is proposed to predict the isotopic cross-sections in proton induced spallation reactions.Learning from more than 4000 data sets of isotopic cross-sections from 19 experimental measurements and 5 theoretical predictions with the SPACS parametrization,in which the mass of the spallation system ranges from 36 to 238,and the incident energy from 200 MeV/u to 1500 MeV/u,it is demonstrated that the BNN method can provide good predictions of the residue fragment cross-sections in spallation reactions.
