Three processing techniques, split-squaring(SS),V-grooving(VG), and split-edging(SE), were evaluated and compared in terms of their processing time and recovery. Semantan bamboo(Gigantochloa scortechinii Gamble) was u...Three processing techniques, split-squaring(SS),V-grooving(VG), and split-edging(SE), were evaluated and compared in terms of their processing time and recovery. Semantan bamboo(Gigantochloa scortechinii Gamble) was used as a raw material and the results showed that the VG-method required the longest processing time(32.1 min), followed by the SS-method(18.2 min), and the SE-method(17.9 min). However, the VG-method showed the highest recovery(82.0%) compared to the SS-method and SE-method, 31.0 and 49.4%, respectively. When both processing time and recovery factors were combined with the same weighing factor, the highest value was recorded with the VG-method(49.1), while the SE-method had values of 31.1 and the SS-method 12.8. The results suggest that the VG-method is the best option. However, the V-grooving machine is still a prototype and therefore the SE-method could be an alternative option until the improved V-grooving machine is available.展开更多
Bamboo fibers were used as source to prepare cellulose hydrogel films for cell cultivation scaffold. The preparation of cellulose solutions was carried out by three different dissolving methods with NaOH-based and NaO...Bamboo fibers were used as source to prepare cellulose hydrogel films for cell cultivation scaffold. The preparation of cellulose solutions was carried out by three different dissolving methods with NaOH-based and NaOH/urea aqueous solutions and DMAc/LiCl solution. Several hydrogel films were elaborated and their properties were compared to evaluate the effect of the dissolving method. It was found that tensile strength of the resultant hydrogel films increased from 21 to 66 N/mm2 when DMAc/LiCl was used instead of the NaOH/urea solution. The same tendency was observed in the obtained elongation values. Moreover, a remarkable difference in fibroblast cell cultivation was observed in higher cell density, when DMAc/LiCl method was used. The obtained results with DMAc/LiCl also were seen to be higher than the results for PS dish used as control. However, low cytocompatibility was observed when NaOH and NaOH/urea methods were used. The obtained results showed that hydrogel films elaborated with cellulose solution prepared with DMAc/LiCl method exhibited good cytocompatibility for the cell cultivation scaffold.展开更多
Previously, Polyvinyl Alcohol (PVA) and phenolic resin were used for resin impregnated bamboo fiber reinforced PP composites which was manufactures for resin impregnated bamboo fiber with polypropylene (PP). Resin imp...Previously, Polyvinyl Alcohol (PVA) and phenolic resin were used for resin impregnated bamboo fiber reinforced PP composites which was manufactures for resin impregnated bamboo fiber with polypropylene (PP). Resin impregnation method can show improvement on tensile strength of fiber. However, to reduce the contact surface area and low inter-facial shear strength (IFSS) between impregnated resin and matrix, using 40% weight fraction of bamboo fiber in PP matrix, PVA impregnated composites with mean flexural and tensile strength 10% higher than untreated composites were produced butphenolic resin impregnated fiber reinforced composition’s mechanical properties were decreased. In this study maleic anhydride grafted polypropylene (MAPP) was used to increase interfacial shear strength between resin impregnated fiber and PP. With 10% MAPP, IFSS between resin impregnated fiber and PP increased more than 100% and reinforced composites. MAPP with untreated, phenolic resin and PVA impregnated cases showed similar mechanical properties. Yet in water absorption test, the PVA treatment with bamboo/PP composites increased water absorption ratio. But with 10% MAPP, matrix PP water absorption ratio decreased like phenolic resin impregnated fiber reinforced composites. 10% MAPP with resin impregnated bamboo fiber reinforced PP composites can improve IFSS, mechanical properties of composite and can decrease water absorption PVA resin impregnated bamboo fiber reinforced composites.展开更多
基金supported by Fundamental Research Grant Scheme(FRGS)Ministry of Higher Education,Malaysia and Higher Institutions’ Centre of Excellence(HICoE)
文摘Three processing techniques, split-squaring(SS),V-grooving(VG), and split-edging(SE), were evaluated and compared in terms of their processing time and recovery. Semantan bamboo(Gigantochloa scortechinii Gamble) was used as a raw material and the results showed that the VG-method required the longest processing time(32.1 min), followed by the SS-method(18.2 min), and the SE-method(17.9 min). However, the VG-method showed the highest recovery(82.0%) compared to the SS-method and SE-method, 31.0 and 49.4%, respectively. When both processing time and recovery factors were combined with the same weighing factor, the highest value was recorded with the VG-method(49.1), while the SE-method had values of 31.1 and the SS-method 12.8. The results suggest that the VG-method is the best option. However, the V-grooving machine is still a prototype and therefore the SE-method could be an alternative option until the improved V-grooving machine is available.
文摘Bamboo fibers were used as source to prepare cellulose hydrogel films for cell cultivation scaffold. The preparation of cellulose solutions was carried out by three different dissolving methods with NaOH-based and NaOH/urea aqueous solutions and DMAc/LiCl solution. Several hydrogel films were elaborated and their properties were compared to evaluate the effect of the dissolving method. It was found that tensile strength of the resultant hydrogel films increased from 21 to 66 N/mm2 when DMAc/LiCl was used instead of the NaOH/urea solution. The same tendency was observed in the obtained elongation values. Moreover, a remarkable difference in fibroblast cell cultivation was observed in higher cell density, when DMAc/LiCl method was used. The obtained results with DMAc/LiCl also were seen to be higher than the results for PS dish used as control. However, low cytocompatibility was observed when NaOH and NaOH/urea methods were used. The obtained results showed that hydrogel films elaborated with cellulose solution prepared with DMAc/LiCl method exhibited good cytocompatibility for the cell cultivation scaffold.
文摘Previously, Polyvinyl Alcohol (PVA) and phenolic resin were used for resin impregnated bamboo fiber reinforced PP composites which was manufactures for resin impregnated bamboo fiber with polypropylene (PP). Resin impregnation method can show improvement on tensile strength of fiber. However, to reduce the contact surface area and low inter-facial shear strength (IFSS) between impregnated resin and matrix, using 40% weight fraction of bamboo fiber in PP matrix, PVA impregnated composites with mean flexural and tensile strength 10% higher than untreated composites were produced butphenolic resin impregnated fiber reinforced composition’s mechanical properties were decreased. In this study maleic anhydride grafted polypropylene (MAPP) was used to increase interfacial shear strength between resin impregnated fiber and PP. With 10% MAPP, IFSS between resin impregnated fiber and PP increased more than 100% and reinforced composites. MAPP with untreated, phenolic resin and PVA impregnated cases showed similar mechanical properties. Yet in water absorption test, the PVA treatment with bamboo/PP composites increased water absorption ratio. But with 10% MAPP, matrix PP water absorption ratio decreased like phenolic resin impregnated fiber reinforced composites. 10% MAPP with resin impregnated bamboo fiber reinforced PP composites can improve IFSS, mechanical properties of composite and can decrease water absorption PVA resin impregnated bamboo fiber reinforced composites.
