The nanometer Al2O3 dispersion strengthened NiCoCrAlY high-temperature protective coatings by crosscurrent CO2 laser on Ni-based superalloy GH4033 were produced. Microscopic morphologies, phase constitutions of claddi...The nanometer Al2O3 dispersion strengthened NiCoCrAlY high-temperature protective coatings by crosscurrent CO2 laser on Ni-based superalloy GH4033 were produced. Microscopic morphologies, phase constitutions of cladding coatings and distribution of nano-Al2O3 particles were examined using SEM and XRD. The results show that the interface grains, after adding proper nano-Al2O3, grow from epitaxial to non-epitaxial shape gradually, and the columnar dendrites become thinner and denser with cellular shape. Cracks in the substrate close to the interface are eliminated. Moreover, dispersive nano-Al2O3 particles mainly distribute around cellular substructure and on grain-boundaries, which prevents the diffusion of alloying elements and restrains the formation of new phase. There is a critical value of nano-Al2O3 addition, and the most suitable content of nano-Al2O3 is 1% (mass fraction) in this experimental conditions. The "nanometer effect" of nano-Al2O3 particles plays an important role in the improvement of coating microstructure.展开更多
A series of iron-based Fischer-Tropsch synthesis （FTS） catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characteriz...A series of iron-based Fischer-Tropsch synthesis （FTS） catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduction/desorption （TPR/TPD） and MSssbauer effect spectroscopy （MES） methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 （weight basis）. After the point, it decreases with further increase in Al2O3 content. The incorporation of Al2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor （CSTR） under the reaction conditions of 260 ℃, 1.5 MPa, 1000 h^-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction （WGS） activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.展开更多
Metal-insulator-metal （MIM） capacitors with atomic-layer-deposited Al2O3 dielectric and reactively sputtered TaN electrodes in application to radio frequency integrated circuits have been characterized electrically....Metal-insulator-metal （MIM） capacitors with atomic-layer-deposited Al2O3 dielectric and reactively sputtered TaN electrodes in application to radio frequency integrated circuits have been characterized electrically. The capacitors exhibit a high density of about 6.05 fF/μm^2, a small leakage current of 4.8 × 10^-8 A/cm^2 at 3 V, a high breakdown electric field of 8.61 MV/cm as well as acceptable voltage coefficients of capacitance （VCCs） of 795 ppm/V2 and 268ppm/V at 1 MHz. The observed properties should be attributed to high-quality Al2O3 film and chemically stable TaN electrodes. Further, a logarithmically linear relationship between quadratic VCC and frequency is observed due to the change of relaxation time with carrier mobility in the dielectric. The conduction mechanism in the high field ranges is dominated by the Poole-Frenkel emission, and the leakage current in the low field ranges is likely to be associated with trap-assisted tunnelling. Meanwhile, the Al2O3 dielectric presents charge trapping under low voltage stresses, and defect generation under high voltage stresses, and it has a hard-breakdown performance.展开更多
In recent years, more and more high Al2O3 iron ores were used in East Asia, especially in China, which increased the Al2O3 content in blast furnace (BF) slag and resulted in poor metallurgical properties of slag. Addi...In recent years, more and more high Al2O3 iron ores were used in East Asia, especially in China, which increased the Al2O3 content in blast furnace (BF) slag and resulted in poor metallurgical properties of slag. Adding MgO-bearing flux is one of the methods to improve the metallurgical properties of slag with high Al2O3. However, there is lack of theoretical basis for the proper MgO/Al2O3 ratio. Therefore, the properties of slag in SiO2-CaO-MgO-Al2O3 system were investigated based on viscosity experiments and phase diagram analyses at 1500℃, and the proper MgO/Al2O3 ratio was explored according to the Al2O3 content in slag. The experimental results show that: (1) in the case of Al2O3 content less than 14mass%, there is no limitation of the MgO/Al2O3 ratio, and the amount of MgO in slag can be determined according to the hearth tempera-ture and desulfurization;(2) in the case of Al2O3 content between 15 and 17mass%, the proper MgO/Al2O3 ratio should be 0.40-0.50;(3) in the case of Al2O3 content between 18 and 20mass%, the proper MgO/Al2O3 ratio should be 0.45-0.55. Consequently, the three-segment control theory of MgO/Al2O3 for BF slag was built, and the actual BF performances proved the validity and applicability of this theory. The research contents and results can give theoretical guidelines for stable BF operation in a wide range of Al2O3 content of 12-20mass%.展开更多
The effects of CaO/Al2O3 ratio on viscosity and structure of the CaO-Al2O3-based fluoride-free mould fluxes were investigated with the CaO/Al2O3 ratio varied from 1 to 4 and the content of SiO2 fixed at 7 wt.%. The in...The effects of CaO/Al2O3 ratio on viscosity and structure of the CaO-Al2O3-based fluoride-free mould fluxes were investigated with the CaO/Al2O3 ratio varied from 1 to 4 and the content of SiO2 fixed at 7 wt.%. The increase in the CaO/Al2O3 ratio from 1 to 2 lowered the viscosity of the flux melts. The viscosity increased slightly with the CaO/Al2O3 ratio from 2 to 3, and this increase became significant with further increasing CaO/Al2O3 ratio to 4. Both break temperature and apparent activation energy were found to be increased with the increase in CaO/Al2O3 ratio from 2 to 4. There was no break temperature available in the flux with CaO/Al2O3 ratio of 1. Changing the CaO/Al2O3 ratio from 1 to 2 decreased the apparent activation energy. Equilibrium phases of the fluxes were calculated using FactSage 7.1 and the major phases were found to be varied with the CaO/Al2O3 ratio. Structures of tested mould fluxes were analysed using Fourier transform infrared spectroscopy. The results showed that the increase in the CaO/Al2O3 ratio from 1 to 2 decreased the complexity of the structure, leading to a reduced viscosity. With the increase in the CaO/Al2O3 ratio from 2 to 4, both solid phase precipitation and melt structure contributed to the variation of viscosity.展开更多
A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roas...A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roasting temperature of 750℃ and roasting time of 30 min, molar ratio of Na2O to Al2O3 of 1.2, the leaching rates of alumina, vanadium and molybdenum in the spent catalyst are 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by precipitators A and B, and the precipitation rates of vanadium and molybdenum are 94.8% and 92.6%. Al（OH）3 was prepared from sodium aluminate solution in the carbonation decomposition process, and the purity of Al2O3 is 99.9% after calcination, the recovery of alumina reaches 90.6% in the whole process; the Ni-Co concentrate was leached by sulfuric acid, a nickel recovery of 98.2% and cobalt recovery over 98.5% can be obtained under the experimental condition of 30% H2SO4, 80℃, reaction time 4 h, mass ratio of liquid to solid 8, stirring rate 800r/min.展开更多
Nickel-alumina catalysts supported on cordierite monoliths of honeycomb structure surpass essentially the conventional granulated ones with respect to the output in carbon dioxide reforming of methane. Adjusting the s...Nickel-alumina catalysts supported on cordierite monoliths of honeycomb structure surpass essentially the conventional granulated ones with respect to the output in carbon dioxide reforming of methane. Adjusting the surface acid-base properties of catalysts by introduction of alkali metal （Na, K） oxides inhibits the carbonization and as a result, improves the operational stability of these catalysts. An effect of promotion of nickel-alumina based composite doped by lanthanum oxide is found. This effect, caused by an additional route for the CO2 activation on Ni-La2O3/Al2O3/cordierite catalyst, is displayed in increase of methane conversion under conditions of an oxidant excess.展开更多
In present study, BP neural network model was proposed for the prediction of ultimate compressive strength of Al2O3-ZrO2 ceramic foam filter prepared by centrifugal slip casting. The inputs of the BP neural network mo...In present study, BP neural network model was proposed for the prediction of ultimate compressive strength of Al2O3-ZrO2 ceramic foam filter prepared by centrifugal slip casting. The inputs of the BP neural network model were the applied load on the epispastic polystyrene template （F）, centrifugal acceleration （v） and sintering temperature （T）, while the only output was the ultimate compressive strength （（7）. According to the registered BP model, the effects of F, v, T on 0 were analyzed. The predicted results agree with the actual data within reasonable experimental error, indicating that the BP model is practically a very useful tool in property prediction and process parameter design of the Al2O3-ZrO2 ceramic foam filter prepared by centrifugal slip casting.展开更多
Two types of enhancement-mode(E-mode)AlGaN/GaN metal-insulator-semiconductor high-electron-mobility transistors(MIS-HEMTs)with different gate insulators are fabricated on Si substrates.The HfO2 gate insulator and the ...Two types of enhancement-mode(E-mode)AlGaN/GaN metal-insulator-semiconductor high-electron-mobility transistors(MIS-HEMTs)with different gate insulators are fabricated on Si substrates.The HfO2 gate insulator and the Al2O3 gate insulator each with a thickness of 30 nm are grown by the plasma-enhanced atomic layer deposition(PEALD).The energy band diagrams of two types of dielectric MIS-HEMTs are compared.The breakdown voltage(VBR)of HfO2 dielectric layer and Al2O3 dielectric layer are 9.4 V and 15.9 V,respectively.With the same barrier thickness,the transconductance of MIS-HEMT with HfO2 is larger.The threshold voltage(Vth)of the HfO2 and Al2O3 MIS-HEMT are 2.0 V and 2.4 V,respectively,when the barrier layer thickness is 0 nm.The C-V characteristics are in good agreement with the Vth's transfer characteristics.As the barrier layer becomes thinner,the drain current density decreases sharply.Due to the dielectric/AlGaN interface is very close to the channel,the scattering of interface states will lead the electron mobility to decrease.The current collapse and the Ron of Al2O3 MIS-HEMT are smaller at the maximum gate voltage.As Al2O3 has excellent thermal stability and chemical stability,the interface state density of Al2O3/AlGaN is less than that of HfO2/AlGaN.展开更多
The desulfurization experiment of an Al2O3-CaO base pre-molten refining slag containing SrO was carried out. Experimental samples were made from industrial materials. In order to predict the slag's desulfurization...The desulfurization experiment of an Al2O3-CaO base pre-molten refining slag containing SrO was carried out. Experimental samples were made from industrial materials. In order to predict the slag's desulfurization ability, sulphur capacity was calculated by means of optical basicity, and there is consistency between calculated results and experimental data. A mathematical model between components and sulphur partition ratio was established with the experimental data. Based on the regression equation, the effects of single and interactive components on sulphur partition ratio were discussed. The results show that the sulphur capacity and distribution ratio decrease with the increment of Al2O3/CaO. SrO and MgO can increase the sulphur partition ratio. The best content of SrO in the slag should not be more than 10%, and the MgO content should be about 8%. The effect of CaF2 on sulphur partition ratio is not obvious, therefore the addition should be limited for environmental protection.展开更多
Because of the discrete charge storage mechanism, charge trapping memory（CTM） technique is a good candidate for aerospace and military missions. The total ionization dose（TID） effects on CTM cells with Al2O3/HfO2/...Because of the discrete charge storage mechanism, charge trapping memory（CTM） technique is a good candidate for aerospace and military missions. The total ionization dose（TID） effects on CTM cells with Al2O3/HfO2/Al2O3（AHA） high-k gate stack structure under in-situ 10 keV x-rays are studied. The C-V characteristics at different radiation doses demonstrate that charge stored in the device continues to be leaked away during the irradiation,thereby inducing the shift of flat band voltage（V（fb））. The dc memory window shows insignificant changes, suggesting the existence of good P/E ability. Furthermore, the physical mechanisms of TID induced radiation damages in AHA-based CTM are analyzed.展开更多
基金Project(20060287019) supported by the Research Fund for Doctoral Program of Higher Education of ChinaProject(kjsmcx07001) supported by the Opening Research Fund of Jiangsu Key Laboratory of Tribology, ChinaProject(CX08B-039Z) supported by the Graduate Innovation Foundation of Jiangsu Province, China
文摘The nanometer Al2O3 dispersion strengthened NiCoCrAlY high-temperature protective coatings by crosscurrent CO2 laser on Ni-based superalloy GH4033 were produced. Microscopic morphologies, phase constitutions of cladding coatings and distribution of nano-Al2O3 particles were examined using SEM and XRD. The results show that the interface grains, after adding proper nano-Al2O3, grow from epitaxial to non-epitaxial shape gradually, and the columnar dendrites become thinner and denser with cellular shape. Cracks in the substrate close to the interface are eliminated. Moreover, dispersive nano-Al2O3 particles mainly distribute around cellular substructure and on grain-boundaries, which prevents the diffusion of alloying elements and restrains the formation of new phase. There is a critical value of nano-Al2O3 addition, and the most suitable content of nano-Al2O3 is 1% (mass fraction) in this experimental conditions. The "nanometer effect" of nano-Al2O3 particles plays an important role in the improvement of coating microstructure.
基金The financial support from the National Natural Science Foundation of China (20590361)the National Outstanding Young Scientists Foundation of China (20625620)
文摘A series of iron-based Fischer-Tropsch synthesis （FTS） catalysts incorporated with Al2O3 binder were prepared by the combination of co-precipitation and spray drying technology. The catalyst samples were characterized by using N2 physical adsorption, temperature-programmed reduction/desorption （TPR/TPD） and MSssbauer effect spectroscopy （MES） methods. The characterization results indicated that the BET surface area increases with increasing Al2O3 content and passes through a maximum at the Al2O3/Fe ratio of 10/100 （weight basis）. After the point, it decreases with further increase in Al2O3 content. The incorporation of Al2O3 binder was found to weaken the surface basicity and suppress the reduction and carburization of iron-based catalysts probably due to the strong K-Al2O3 and Fe-Al2O3 interactions. Furthermore, the H2 adsorption ability of the catalysts is enhanced with increasing Al2O3 content. The FTS performances of the catalysts were tested in a slurry-phase continuously stirred tank reactor （CSTR） under the reaction conditions of 260 ℃, 1.5 MPa, 1000 h^-1 and molar ratio of H2/CO 0.67 for 200 h. The results showed that the addition of small amounts of Al2O3 affects the activity of iron-based catalysts to a little extent. However, with further increase of Al2O3 content, the FTS activity and water gas shift reaction （WGS） activity are decreased severely. The addition of appropriate Al2O3 do not affect the product selectivity, but the catalysts incorporated with large amounts of Al2O3 have higher selectivity for light hydrocarbons and lower selectivity for heavy hydrocarbons.
基金Project supported by the National Natural Science Foundation of China （Grant No 90607023）, Shanghai Pujiang Program （Grant No 05PJ14017）, SRF for R0CS, SEM, and the Micro/Nano-electronics Science and Technology Innovation Platform （985） and the Ministry of Education of China in the International Research Training Group ＂Materials and Concepts for Advanced Interconnects
文摘Metal-insulator-metal （MIM） capacitors with atomic-layer-deposited Al2O3 dielectric and reactively sputtered TaN electrodes in application to radio frequency integrated circuits have been characterized electrically. The capacitors exhibit a high density of about 6.05 fF/μm^2, a small leakage current of 4.8 × 10^-8 A/cm^2 at 3 V, a high breakdown electric field of 8.61 MV/cm as well as acceptable voltage coefficients of capacitance （VCCs） of 795 ppm/V2 and 268ppm/V at 1 MHz. The observed properties should be attributed to high-quality Al2O3 film and chemically stable TaN electrodes. Further, a logarithmically linear relationship between quadratic VCC and frequency is observed due to the change of relaxation time with carrier mobility in the dielectric. The conduction mechanism in the high field ranges is dominated by the Poole-Frenkel emission, and the leakage current in the low field ranges is likely to be associated with trap-assisted tunnelling. Meanwhile, the Al2O3 dielectric presents charge trapping under low voltage stresses, and defect generation under high voltage stresses, and it has a hard-breakdown performance.
基金The financial supports of National Natural Science Foundation of China(NSFC 51874080,NSFC 51774071,and NSFC 51974073)Natural Science Foundation of Liaoning(2019-MS-132)are much appreciated.
文摘In recent years, more and more high Al2O3 iron ores were used in East Asia, especially in China, which increased the Al2O3 content in blast furnace (BF) slag and resulted in poor metallurgical properties of slag. Adding MgO-bearing flux is one of the methods to improve the metallurgical properties of slag with high Al2O3. However, there is lack of theoretical basis for the proper MgO/Al2O3 ratio. Therefore, the properties of slag in SiO2-CaO-MgO-Al2O3 system were investigated based on viscosity experiments and phase diagram analyses at 1500℃, and the proper MgO/Al2O3 ratio was explored according to the Al2O3 content in slag. The experimental results show that: (1) in the case of Al2O3 content less than 14mass%, there is no limitation of the MgO/Al2O3 ratio, and the amount of MgO in slag can be determined according to the hearth tempera-ture and desulfurization;(2) in the case of Al2O3 content between 15 and 17mass%, the proper MgO/Al2O3 ratio should be 0.40-0.50;(3) in the case of Al2O3 content between 18 and 20mass%, the proper MgO/Al2O3 ratio should be 0.45-0.55. Consequently, the three-segment control theory of MgO/Al2O3 for BF slag was built, and the actual BF performances proved the validity and applicability of this theory. The research contents and results can give theoretical guidelines for stable BF operation in a wide range of Al2O3 content of 12-20mass%.
文摘The effects of CaO/Al2O3 ratio on viscosity and structure of the CaO-Al2O3-based fluoride-free mould fluxes were investigated with the CaO/Al2O3 ratio varied from 1 to 4 and the content of SiO2 fixed at 7 wt.%. The increase in the CaO/Al2O3 ratio from 1 to 2 lowered the viscosity of the flux melts. The viscosity increased slightly with the CaO/Al2O3 ratio from 2 to 3, and this increase became significant with further increasing CaO/Al2O3 ratio to 4. Both break temperature and apparent activation energy were found to be increased with the increase in CaO/Al2O3 ratio from 2 to 4. There was no break temperature available in the flux with CaO/Al2O3 ratio of 1. Changing the CaO/Al2O3 ratio from 1 to 2 decreased the apparent activation energy. Equilibrium phases of the fluxes were calculated using FactSage 7.1 and the major phases were found to be varied with the CaO/Al2O3 ratio. Structures of tested mould fluxes were analysed using Fourier transform infrared spectroscopy. The results showed that the increase in the CaO/Al2O3 ratio from 1 to 2 decreased the complexity of the structure, leading to a reduced viscosity. With the increase in the CaO/Al2O3 ratio from 2 to 4, both solid phase precipitation and melt structure contributed to the variation of viscosity.
基金Project(2003 UDBEA00C020) supported by the Collaborative Project of School and Province of Yunnan Province
文摘A new technology was developed to recover multiple valuable elements from the spent Al2O3-based catalyst by X-ray phase analysis and exploratory experiments. The experimental results show that in the condition of roasting temperature of 750℃ and roasting time of 30 min, molar ratio of Na2O to Al2O3 of 1.2, the leaching rates of alumina, vanadium and molybdenum in the spent catalyst are 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by precipitators A and B, and the precipitation rates of vanadium and molybdenum are 94.8% and 92.6%. Al（OH）3 was prepared from sodium aluminate solution in the carbonation decomposition process, and the purity of Al2O3 is 99.9% after calcination, the recovery of alumina reaches 90.6% in the whole process; the Ni-Co concentrate was leached by sulfuric acid, a nickel recovery of 98.2% and cobalt recovery over 98.5% can be obtained under the experimental condition of 30% H2SO4, 80℃, reaction time 4 h, mass ratio of liquid to solid 8, stirring rate 800r/min.
文摘Nickel-alumina catalysts supported on cordierite monoliths of honeycomb structure surpass essentially the conventional granulated ones with respect to the output in carbon dioxide reforming of methane. Adjusting the surface acid-base properties of catalysts by introduction of alkali metal （Na, K） oxides inhibits the carbonization and as a result, improves the operational stability of these catalysts. An effect of promotion of nickel-alumina based composite doped by lanthanum oxide is found. This effect, caused by an additional route for the CO2 activation on Ni-La2O3/Al2O3/cordierite catalyst, is displayed in increase of methane conversion under conditions of an oxidant excess.
基金financially supported by the Innovation Research Team Program of the Ministry of Education(IRT0713)the Key Laboratory of New Materials in Automobile of Liaoning Province(grant No.201016201)Doctoral Initiating Project of Liaoning Province Foundation for Natural Sciences,China
文摘In present study, BP neural network model was proposed for the prediction of ultimate compressive strength of Al2O3-ZrO2 ceramic foam filter prepared by centrifugal slip casting. The inputs of the BP neural network model were the applied load on the epispastic polystyrene template （F）, centrifugal acceleration （v） and sintering temperature （T）, while the only output was the ultimate compressive strength （（7）. According to the registered BP model, the effects of F, v, T on 0 were analyzed. The predicted results agree with the actual data within reasonable experimental error, indicating that the BP model is practically a very useful tool in property prediction and process parameter design of the Al2O3-ZrO2 ceramic foam filter prepared by centrifugal slip casting.
基金the National Natural Science Foundation of China(Grant Nos.61974111,11690042,and 61974115)the National Pre-research Foundation of China(Grant No.31512050402)the Fund of Innovation Center of Radiation Application,China(Grant No.KFZC2018040202).
文摘Two types of enhancement-mode(E-mode)AlGaN/GaN metal-insulator-semiconductor high-electron-mobility transistors(MIS-HEMTs)with different gate insulators are fabricated on Si substrates.The HfO2 gate insulator and the Al2O3 gate insulator each with a thickness of 30 nm are grown by the plasma-enhanced atomic layer deposition(PEALD).The energy band diagrams of two types of dielectric MIS-HEMTs are compared.The breakdown voltage(VBR)of HfO2 dielectric layer and Al2O3 dielectric layer are 9.4 V and 15.9 V,respectively.With the same barrier thickness,the transconductance of MIS-HEMT with HfO2 is larger.The threshold voltage(Vth)of the HfO2 and Al2O3 MIS-HEMT are 2.0 V and 2.4 V,respectively,when the barrier layer thickness is 0 nm.The C-V characteristics are in good agreement with the Vth's transfer characteristics.As the barrier layer becomes thinner,the drain current density decreases sharply.Due to the dielectric/AlGaN interface is very close to the channel,the scattering of interface states will lead the electron mobility to decrease.The current collapse and the Ron of Al2O3 MIS-HEMT are smaller at the maximum gate voltage.As Al2O3 has excellent thermal stability and chemical stability,the interface state density of Al2O3/AlGaN is less than that of HfO2/AlGaN.
文摘The desulfurization experiment of an Al2O3-CaO base pre-molten refining slag containing SrO was carried out. Experimental samples were made from industrial materials. In order to predict the slag's desulfurization ability, sulphur capacity was calculated by means of optical basicity, and there is consistency between calculated results and experimental data. A mathematical model between components and sulphur partition ratio was established with the experimental data. Based on the regression equation, the effects of single and interactive components on sulphur partition ratio were discussed. The results show that the sulphur capacity and distribution ratio decrease with the increment of Al2O3/CaO. SrO and MgO can increase the sulphur partition ratio. The best content of SrO in the slag should not be more than 10%, and the MgO content should be about 8%. The effect of CaF2 on sulphur partition ratio is not obvious, therefore the addition should be limited for environmental protection.
基金Supported by the National Natural Science Foundation of China under Grant No 616340084the Youth Innovation Promotion Association of Chinese Academy of Sciences under Grant No 2014101+1 种基金the International Cooperation Project of Chinese Academy of Sciencesthe Austrian-Chinese Cooperative R&D Projects under Grant No 172511KYSB20150006
文摘Because of the discrete charge storage mechanism, charge trapping memory（CTM） technique is a good candidate for aerospace and military missions. The total ionization dose（TID） effects on CTM cells with Al2O3/HfO2/Al2O3（AHA） high-k gate stack structure under in-situ 10 keV x-rays are studied. The C-V characteristics at different radiation doses demonstrate that charge stored in the device continues to be leaked away during the irradiation,thereby inducing the shift of flat band voltage（V（fb））. The dc memory window shows insignificant changes, suggesting the existence of good P/E ability. Furthermore, the physical mechanisms of TID induced radiation damages in AHA-based CTM are analyzed.
