Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO...Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO 2(a natase), Al 2SiO 5, and ZrO 2 in these membranes. Changing the molar ratio of Al∶Si∶Ti∶Zr,the kinds and content of crystal phases of composite membranes could be different, which may lead to a variety of microstructure of membranes. The surface nanoscale topography and microstructure of membranes were investiga ted by XRD,SEM,AFM,EPMA. The effects of additives and heat treatments on the sur face nanoscale topography and microstructure of composite ceramic membranes were also analyzed.展开更多
The oxidation behavior of Al2O3-30%TiCN-0.2%Y2O3 composite and its effect on high temperature bending strength was studied. The result indicates that the mass gain during static oxidation of the material under normal ...The oxidation behavior of Al2O3-30%TiCN-0.2%Y2O3 composite and its effect on high temperature bending strength was studied. The result indicates that the mass gain during static oxidation of the material under normal atmosphere follows the parabolic law. Oxide increases with increasing temperature and prolonging time. It has good oxidation resistance. The product of oxidation of the material is TiO2. Therefore, the volume of the material expands. The oxide film is destroyed because residual stress inside the oxide film is released. Proper oxidation is beneficial to the improvement of bending strength of Al2O3-30%TiCN-0.2%Y2O3 composite. The strength increase is up to 4.5%.展开更多
Thermal shock resistance of Al2O3-TiCN(30%)-Y2O3(0.2%) composite was studied by hot pressing(HP) method at different temperatures. The study shows that thermal shock resistance of the material is determined by its mic...Thermal shock resistance of Al2O3-TiCN(30%)-Y2O3(0.2%) composite was studied by hot pressing(HP) method at different temperatures. The study shows that thermal shock resistance of the material is determined by its microstructure and reinforced mechanism. According to SEM and calculation of thermal shock, the fractured surface of Al2O3-30%TiCN-0.2%Y2O3 composite is undulate. The residual strength of Al2O3-30%TiCN-0.2%Y2O3 is higher than Al2O3-30%TiCN at 200～800 ℃ after thermal shock. Cracks initiation resistance (R′)and cracks propagation resistance (R″″)of Al2O3-30%TiCN-0.2%Y2O3 composite increases 12% and 5% respectively compared with that of Al2O3-30%TiCN. It matches with experimental results. The addition of Y2O3 forms YAG that inhibits crystal growth, and increases fracture stress, fracture toughness, cracks initiation resistance and cracks propagation resistance. Therefore, thermal shock resistance increases. The fracture work of Al2O3-30%TiCN and Al2O3-30%TiCN-0.2%Y2O3 composites are 132 and 148 J·m-2 respectively.展开更多
以尿素催化硅酸乙酯水解制得SiO2溶胶。采用29Si NMR、27 Al NMR、FT-IR、TEM、DTA、XRD和SEM等对SiO2溶胶、Al2O3凝胶纤维化学结构和微观结构研究结果表明,该SiO2溶胶稳定性好,含有大量的单硅酸Si(OH)4,能和Al2O3表面的Al—OH反应生成A...以尿素催化硅酸乙酯水解制得SiO2溶胶。采用29Si NMR、27 Al NMR、FT-IR、TEM、DTA、XRD和SEM等对SiO2溶胶、Al2O3凝胶纤维化学结构和微观结构研究结果表明,该SiO2溶胶稳定性好,含有大量的单硅酸Si(OH)4,能和Al2O3表面的Al—OH反应生成Al—O—Si键而有效地将其包裹,从而阻止了过渡态Al2O3微晶的相互接触,抑制了α-Al2O3的成核和生长。展开更多
Attempts had been made to synthesize Al2O3-2SiO2 nanopowders by sol-gel method with tetraethoxysilane（TEOS） and aluminum nitrate（ANN） as the starting materials.DTS,TEM,SEM and BET were employed to study the effect...Attempts had been made to synthesize Al2O3-2SiO2 nanopowders by sol-gel method with tetraethoxysilane（TEOS） and aluminum nitrate（ANN） as the starting materials.DTS,TEM,SEM and BET were employed to study the effects of process parameters on the size,specific surface area and structure（morphology） of powders.The alkali-activation reactivity of the powders was tested for manufacturing geopolymers and their hydrothermal reactions were performed for fabricating zeolites.The results show that the optimum process parameters and drying method for preparing Al2O3-2SiO2 nanopowders are as follows：the molar ratio of water and ethanol to TEOS are 0：1 and 12：1 respectively at synthetic temperature of 50 ℃ and the drying method is azeotropic distillation with microwave drying.The average particle diameters of the powders were about 70 nm and the largest BET specific surface area was up to 669 m^2·g^-1.The compressive strength of the geopolymer and the calcium exchange capacity（by CaCO3） of NaA zeolite prepared with the powders reached to 29 MPa and 366 m^2·g^-1 respectively.展开更多
The various surface species[H_XRu_3(CO)_9(CCO)]^(2-X)(X=0-2)prepared from impregnation of[PPN]_2[Ru_3(CO)_9(CCO)]on SiO_2-Al_2O_3,SiO_2 and MgO show quite different activities and selectivities for oxygenates and etha...The various surface species[H_XRu_3(CO)_9(CCO)]^(2-X)(X=0-2)prepared from impregnation of[PPN]_2[Ru_3(CO)_9(CCO)]on SiO_2-Al_2O_3,SiO_2 and MgO show quite different activities and selectivities for oxygenates and ethane in ethylene hydroformylation.展开更多
The effective B acid amount of dealuminated USY(DUSY) zeolites with different silica/alumina ratios were measured by UV spectrometry with 2,6 dimethyl pyridine as adsorbentes in the presence of cyclohexane or anhydrou...The effective B acid amount of dealuminated USY(DUSY) zeolites with different silica/alumina ratios were measured by UV spectrometry with 2,6 dimethyl pyridine as adsorbentes in the presence of cyclohexane or anhydrous ethanol or tetrahydrofuran.The isomerization of α pinene was used to check the acidic catalytic properties of these zeolites.The results indicate that effective B acid amount of DUSY measured in polar anhydrous ethanol or tetrahydrofuran is lower than that of non polar cyclohexane.The effect of solution concentration of effective B acid amount of DUSY zeolites is small.As the silica/alumina ratio of catalyst increases,effective B acid amount and conversion of isomerization of α pinene all raise.展开更多
Al2O3-ZrO2 with a high level of hardness and toughness is known as ceramic steel. Due to its unique properties it can be used as a reinforcement in fabrication of metal matrix composites. In this study, nanoparticles ...Al2O3-ZrO2 with a high level of hardness and toughness is known as ceramic steel. Due to its unique properties it can be used as a reinforcement in fabrication of metal matrix composites. In this study, nanoparticles of Al2O3-10% ZrO2 with an average size of 80 nm were used to fabricate Al matrix composites containing 0.5, 1, 1.5 and 2 wt.% of the reinforcement. The fabrication route was stir casting at 850?C. There is no report about usage of this reinforcement in fabrication of composites in the literature. The microstructures of the as-cast composites were studied by scanning electron microscope (SEM). Density measurement, hardness and tensile properties were carried out to identify the mechanical properties of the composites. The results revealed that with increasing the reinforcement content, density decreased while yield, ultimate tensile strength and compressive strength increased. Also, hardness increased by increasing the reinforcement content up to 1 wt.% Al2O3-10% ZrO2 but it decreased in the samples containing higher amounts of reinforcement.展开更多
文摘Al 2O 3-SiO 2-TiO 2-ZrO 2 supported membranes were prepar ed by Sol-Gel method. These composite ceramic membranes are level, even and no macro crack. There exist several crystalline phases such as Al 2O 3, TiO 2(a natase), Al 2SiO 5, and ZrO 2 in these membranes. Changing the molar ratio of Al∶Si∶Ti∶Zr,the kinds and content of crystal phases of composite membranes could be different, which may lead to a variety of microstructure of membranes. The surface nanoscale topography and microstructure of membranes were investiga ted by XRD,SEM,AFM,EPMA. The effects of additives and heat treatments on the sur face nanoscale topography and microstructure of composite ceramic membranes were also analyzed.
文摘The oxidation behavior of Al2O3-30%TiCN-0.2%Y2O3 composite and its effect on high temperature bending strength was studied. The result indicates that the mass gain during static oxidation of the material under normal atmosphere follows the parabolic law. Oxide increases with increasing temperature and prolonging time. It has good oxidation resistance. The product of oxidation of the material is TiO2. Therefore, the volume of the material expands. The oxide film is destroyed because residual stress inside the oxide film is released. Proper oxidation is beneficial to the improvement of bending strength of Al2O3-30%TiCN-0.2%Y2O3 composite. The strength increase is up to 4.5%.
文摘Thermal shock resistance of Al2O3-TiCN(30%)-Y2O3(0.2%) composite was studied by hot pressing(HP) method at different temperatures. The study shows that thermal shock resistance of the material is determined by its microstructure and reinforced mechanism. According to SEM and calculation of thermal shock, the fractured surface of Al2O3-30%TiCN-0.2%Y2O3 composite is undulate. The residual strength of Al2O3-30%TiCN-0.2%Y2O3 is higher than Al2O3-30%TiCN at 200～800 ℃ after thermal shock. Cracks initiation resistance (R′)and cracks propagation resistance (R″″)of Al2O3-30%TiCN-0.2%Y2O3 composite increases 12% and 5% respectively compared with that of Al2O3-30%TiCN. It matches with experimental results. The addition of Y2O3 forms YAG that inhibits crystal growth, and increases fracture stress, fracture toughness, cracks initiation resistance and cracks propagation resistance. Therefore, thermal shock resistance increases. The fracture work of Al2O3-30%TiCN and Al2O3-30%TiCN-0.2%Y2O3 composites are 132 and 148 J·m-2 respectively.
文摘以尿素催化硅酸乙酯水解制得SiO2溶胶。采用29Si NMR、27 Al NMR、FT-IR、TEM、DTA、XRD和SEM等对SiO2溶胶、Al2O3凝胶纤维化学结构和微观结构研究结果表明,该SiO2溶胶稳定性好,含有大量的单硅酸Si(OH)4,能和Al2O3表面的Al—OH反应生成Al—O—Si键而有效地将其包裹,从而阻止了过渡态Al2O3微晶的相互接触,抑制了α-Al2O3的成核和生长。
基金Supported by the National Natural Science Foundation of China (50962002,50602006)Opening Funds of State Key Laboratory of Chemical Resource Engineering of Beijing University of Chemical Technology (201008)
文摘Attempts had been made to synthesize Al2O3-2SiO2 nanopowders by sol-gel method with tetraethoxysilane（TEOS） and aluminum nitrate（ANN） as the starting materials.DTS,TEM,SEM and BET were employed to study the effects of process parameters on the size,specific surface area and structure（morphology） of powders.The alkali-activation reactivity of the powders was tested for manufacturing geopolymers and their hydrothermal reactions were performed for fabricating zeolites.The results show that the optimum process parameters and drying method for preparing Al2O3-2SiO2 nanopowders are as follows：the molar ratio of water and ethanol to TEOS are 0：1 and 12：1 respectively at synthetic temperature of 50 ℃ and the drying method is azeotropic distillation with microwave drying.The average particle diameters of the powders were about 70 nm and the largest BET specific surface area was up to 669 m^2·g^-1.The compressive strength of the geopolymer and the calcium exchange capacity（by CaCO3） of NaA zeolite prepared with the powders reached to 29 MPa and 366 m^2·g^-1 respectively.
文摘The various surface species[H_XRu_3(CO)_9(CCO)]^(2-X)(X=0-2)prepared from impregnation of[PPN]_2[Ru_3(CO)_9(CCO)]on SiO_2-Al_2O_3,SiO_2 and MgO show quite different activities and selectivities for oxygenates and ethane in ethylene hydroformylation.
文摘The effective B acid amount of dealuminated USY(DUSY) zeolites with different silica/alumina ratios were measured by UV spectrometry with 2,6 dimethyl pyridine as adsorbentes in the presence of cyclohexane or anhydrous ethanol or tetrahydrofuran.The isomerization of α pinene was used to check the acidic catalytic properties of these zeolites.The results indicate that effective B acid amount of DUSY measured in polar anhydrous ethanol or tetrahydrofuran is lower than that of non polar cyclohexane.The effect of solution concentration of effective B acid amount of DUSY zeolites is small.As the silica/alumina ratio of catalyst increases,effective B acid amount and conversion of isomerization of α pinene all raise.
文摘Al2O3-ZrO2 with a high level of hardness and toughness is known as ceramic steel. Due to its unique properties it can be used as a reinforcement in fabrication of metal matrix composites. In this study, nanoparticles of Al2O3-10% ZrO2 with an average size of 80 nm were used to fabricate Al matrix composites containing 0.5, 1, 1.5 and 2 wt.% of the reinforcement. The fabrication route was stir casting at 850?C. There is no report about usage of this reinforcement in fabrication of composites in the literature. The microstructures of the as-cast composites were studied by scanning electron microscope (SEM). Density measurement, hardness and tensile properties were carried out to identify the mechanical properties of the composites. The results revealed that with increasing the reinforcement content, density decreased while yield, ultimate tensile strength and compressive strength increased. Also, hardness increased by increasing the reinforcement content up to 1 wt.% Al2O3-10% ZrO2 but it decreased in the samples containing higher amounts of reinforcement.
