The isothermal oxidation kinetics of vanadium–titanium magnetite(VTM)pellets prepared with 3Co-binder(coal-based colloidal composite binder)and F-binder(pulverized Funa binder)are compared.The oxidation process was a...The isothermal oxidation kinetics of vanadium–titanium magnetite(VTM)pellets prepared with 3Co-binder(coal-based colloidal composite binder)and F-binder(pulverized Funa binder)are compared.The oxidation process was analyzed using the first-order irreversible reaction,following the shrinking unreacted nucleus model.The results demonstrate that VTM pellets prepared with 3Co-binder exhibit a faster oxidation rate than those with F-binder across the temperatures ranging from 1073 to 1473 K.In both cases,the oxidation process was controlled by an interfacial chemical reaction during the pre-oxidation stage and by internal diffusion during the mid-oxidation stage.The type of binder did not influence the primary oxidation control mechanism of the VTM pellets.However,the apparent rate constants in the pre-oxidation stage and the internal diffusion coefficients in the mid-oxidation stage were higher for pellets with 3Co-binder compared to those with F-binder.The apparent activation energies for the 3Co-binder pellets were similar to those of bentonite,indicating favorable kinetic conditions without negative impacts on the oxidation process.Nonetheless,it is important to note that pellets with F-binder required a longer oxidation time than those with 3Co-binder.展开更多
Using titanium wires （99.5%, 200 μm in diameter） as a reactive source, an Al-based composite coating reinforced by titanium tri-aluminide （A13Ti） particles was fabricated by infiltration plus in-situ methods. Acc...Using titanium wires （99.5%, 200 μm in diameter） as a reactive source, an Al-based composite coating reinforced by titanium tri-aluminide （A13Ti） particles was fabricated by infiltration plus in-situ methods. According to the differential thermal analysis （DTA） curve, the reactive temperature between Ti wires and A1 matrix can be determined at 890 ℃. The obtained composite coatings were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, and microhardness and wear test. The experimental results show that when holding period is 20 min at 890℃, the titanium wires react completely to in-situ synthesize Al3Ti particles, which presents blocky and strip-like states. The microhardness of in-situ synthesized Al3Ti particles is about 4.5 times that of the Al-matrix. Under the condition of dry sliding at 10 N load, compared with the unreinforced Al matrix, the composite coating fabricated with 20 min offers unique wear resistance behavior, and its wear mechanism is that the adhesive wear and abrasive wear coexist.展开更多
The in-situ Al-based composites with different SiO2/C/Al molar ratios were fabricated by reaction hot pressing. The dry sliding wear characteristics of the composites were investigated using a pin-on-disc wear tester....The in-situ Al-based composites with different SiO2/C/Al molar ratios were fabricated by reaction hot pressing. The dry sliding wear characteristics of the composites were investigated using a pin-on-disc wear tester. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) were used to investigate the surface composition and its morphology. The results show that when the SiO2/C/Al molar ratio is 3:6:9, more in-situ synthesized Al2O3 and SiC along with Si particles are produced, and Al4C3 is prevented completely from the Al?SiO2?C system. Thereby, a significant improvement of wear resistance is obtained. When the sliding velocity increases from 0.4 to 1.6 m/s, the wear loss decreases gradually. With increasing the normal load, the wear loss increases as well. Ploughing, craters and micro-grooving are observed as dominant abrasive wear mechanisms. Whereas, when a high velocity is employed, only the oxidation mechanism controls the wear behavior of the composites.展开更多
An Al-based composite reinforced with core–shell-structured Ti/Al_3Ti was fabricated through a powder metallurgy route followed by hot extrusion and was found to exhibit promising mechanical properties. The ultimate ...An Al-based composite reinforced with core–shell-structured Ti/Al_3Ti was fabricated through a powder metallurgy route followed by hot extrusion and was found to exhibit promising mechanical properties. The ultimate tensile strength and elongation of the composite sintered at 620°C for 5 h and extruded at a mass ratio of 12.75:1 reached 304 MPa and 14%, respectively, and its compressive deformation reached 60%. The promising mechanical properties are due to the core–shell-structured reinforcement, which is mainly composed of Al_3Ti and Ti and is bonded strongly with the Al matrix, and to the reduced crack sensitivity of Al_3Ti. The refined grains after hot extrusion also contribute to the mechanical properties of this composite. The mechanical properties might be further improved through regulating the relative thickness of Al–Ti intermetallics and Ti metal layers by adjusting the sintering time and the subsequent extrusion process.展开更多
TiAl-based composites reinforced with different high volume fractions of nearly network TizAIC phase have been successfully prepared by mechanical alloying and hot-pressing method.Their microstructure.mechanical and t...TiAl-based composites reinforced with different high volume fractions of nearly network TizAIC phase have been successfully prepared by mechanical alloying and hot-pressing method.Their microstructure.mechanical and tribological properties have been investigated.Ti2AIC network becomes continuous but the network wall grows thicker with increasing the Ti2AIC content.The continuity and wall size of the network Ti2AIC phase exert a significant influence on the mechanical properties.The bending strength of the composites first increases and then decreases with the Ti2A1C content.The compressive strength of the composite decreases slightly compared to the TiAI alloy,but the hardness is enhanced.Due to the high hardness and load-carrying capacity of the network structure,these composites have the better wear resistance.And this enhancement is more notable at low applied loads and high Ti2A1C content.The mechanisms simulating the role of network Ti2AIC phase on the wear behavior and the wear process of TiAl/Ti2AIC composites at different applied loads have been proposed.展开更多
Mechanically alloyed NiAl-TiB_2-Y_2O_3 composite (volume percentage of dispersoids about 15v%) was prepared by hot pressing. The compressive properties of the composite from 300 K to 1360 K were tested and the microst...Mechanically alloyed NiAl-TiB_2-Y_2O_3 composite (volume percentage of dispersoids about 15v%) was prepared by hot pressing. The compressive properties of the composite from 300 K to 1360 K were tested and the microstructures were studied mainly by TEM. The yield strengths of the composite at room temperature and high temperatures are considerably higher than that of monolithic NiAl and also is higher than similar NiAl-based composites which contained higher content of dispersoids but showed coarser microstructure. The possible strengthening mechanisms working in the composite are discussed.展开更多
A new Al-based composite consisting of submicron-sized α-Al matrix embedded with precipitated intermetallic phases was developed by controlling the devitrification process of an Al-Ni-Y-Co-La amorphous alloy.Such a h...A new Al-based composite consisting of submicron-sized α-Al matrix embedded with precipitated intermetallic phases was developed by controlling the devitrification process of an Al-Ni-Y-Co-La amorphous alloy.Such a homogeneous composite structure presented an ultrahigh strength of about 1.34 GPa and a large compressive plastic strain up to 22%.The unique mechanical properties during compression are mainly attributed to the dislocation slip deformation of ductile a-AI matrix and the shear-induced refinement of strengthening intermetallic phases.展开更多
An aluminium alloy and its composite with dispersed SiC particles made by liquid metallurgy route were extruded under optimized conditions.The properties were characterized in terms of microstructure,hardness and slid...An aluminium alloy and its composite with dispersed SiC particles made by liquid metallurgy route were extruded under optimized conditions.The properties were characterized in terms of microstructure,hardness and sliding wear behaviour and then compared between the extruded and cast alloys and composites,in order to understand the benefits of composite and extrusion on the alloy.It was observed that composites drastically increased the hardness and the extruded composites further increased this value.The advantage of composites was realized in sliding wear tests.展开更多
An aluminum-based in-situ composites reinforced with Mg2Si and Si particles were produced by centrifugal casting A1-20Si-5Mg alloy. The microstructure of the composites was examined, and the effects of temperature on ...An aluminum-based in-situ composites reinforced with Mg2Si and Si particles were produced by centrifugal casting A1-20Si-5Mg alloy. The microstructure of the composites was examined, and the effects of temperature on fracture behavior of the composite were investigated. The results show that the average fraction of primary Si and Mg2Si particles in the composites is as high as 38%, and ultimate tensile strengths （UTS） of the composites first increase then decrease with the increase of test temperature. Microstructures of broken specimens show that both the particle fracture and the interface debonding affect the fracture behavior of the composites, and the interface debonding becomes the dominant fracture mechanism with increasing test temperature. Comparative results indicate that rich particles in the composites and excellent interface strength play great roles in enhancing tensile property by preventing the movement of dislocations.展开更多
Among various architectures of polymers,end-group-free rings have attracted growing interests due to their distinct physicochemical performances over the linear counterparts which are exemplified by reduced hydrodynam...Among various architectures of polymers,end-group-free rings have attracted growing interests due to their distinct physicochemical performances over the linear counterparts which are exemplified by reduced hydrodynamic size and slower degradation.It is key to develop facile methods to large-scale synthesis of polymer rings with tunable compositions and microstructures.Recent progresses in large-scale synthesis of polymer rings against single-chain dynamic nanoparticles,and the example applications in synchronous enhancing toughness and strength of polymer nanocomposites are summarized.Once there is the breakthrough in rational design and effective large-scale synthesis of polymer rings and their functional derivatives,a family of cyclic functional hybrids would be available,thus providing a new paradigm in developing polymer science and engineering.展开更多
Ultrasonic-Assisted Grinding(UAG)is a novel manufacturing technology that shows promising promise for use in processing Ceramic Matrix Composites(CMCs).Nevertheless,analyzing the material removal process of CMCs with ...Ultrasonic-Assisted Grinding(UAG)is a novel manufacturing technology that shows promising promise for use in processing Ceramic Matrix Composites(CMCs).Nevertheless,analyzing the material removal process of CMCs with multidirectional structure during UAG is challenging,impeding the progress and improvement of the UAG process.This work examined the impact of ultrasonic vibration on the dynamic mechanical characteristics during processing.Additionally,we experimentally elucidated the material removal mechanism of CMCs during the scratching process under the influence of vertical vibration.The results indicate that the introduction of ultrasonic vibration causes a strain rate effect,resulting in a modification of the material removal mechanism,subsequently impacting the processing quality.Ultrasonic vibration increases the dynamic strength and brittleness of the fibers in CMCs,leading to more cracks at fracture,which changes from the original bending fracture to shear fracture.In addition,ultrasonic vibration can effectively inhibit the impact of scratching depth and anisotropy on the removal mechanism of CMCs,resulting in a more uniform surface of CMCs after processing.展开更多
A composite electrocatalyst,CoMoNiO-S/NF-110(NF is nickel foam),was synthesized through electrodeposition,followed by pyrolysis and then the vulcanization process.CoMoNiO-S/NF-110 exhibited a structure where Ni3S2 and...A composite electrocatalyst,CoMoNiO-S/NF-110(NF is nickel foam),was synthesized through electrodeposition,followed by pyrolysis and then the vulcanization process.CoMoNiO-S/NF-110 exhibited a structure where Ni3S2 and Mo2S3 nanoparticles were integrated at the edges of Co3O4 nanosheets,creating a rich,heterogeneous interface that enhances the synergistic effects of each component.In an alkaline electrolyte,the synthesized CoMoNiO-S/NF-110 exhibited superior electrocatalytic performance for oxygen evolution reaction(OER),achieving current densities of 100 and 200 mA·cm^(-2) with low overpotentials of 199.4 and 224.4 mV,respectively,outperforming RuO2 and several high-performance Mo and Ni-based catalysts.This excellent performance is attributed to the rich interface formed between the components and active sites exposed by the defect structure.展开更多
KIT-5/Beta composite supports were synthesized using an in situ self-assembly hydrothermal method,and NiW/KIT-5/Beta catalysts were prepared by impregnation.A series of characterization techniques were utilized to eva...KIT-5/Beta composite supports were synthesized using an in situ self-assembly hydrothermal method,and NiW/KIT-5/Beta catalysts were prepared by impregnation.A series of characterization techniques were utilized to evaluate the influence of varying hydrothermal synthesis temperatures on the physicochemical properties of both the KIT-5/Beta supports and the resulting catalysts.The catalytic performances of catalysts were evaluated under reaction conditions of 320℃,4 MPa H_(2)pressure,and a weight hourly space velocity(WHSV)of 4.8 h^(-1)for hydrodenitrogenation(HDN)of quinoline.The results indicated that the specific surface area and pore structure of the materials could be effectively regulated by adjusting the hydrothermal synthesis temperature,which in turn influenced the number of active sites on the catalyst.The NiW/KB-125 catalyst,synthesized at 125℃,presented the highest quinoline HDN efficiency(96.8%),which can be attributed to its favorable pore channel structure,greater Brønsted acid number,higher degree of metal sulfidation(80.12%)and appropriate metal-support interaction(MSI).展开更多
The poor electrical conductivity of metal-organic frameworks(MOFs)limits their electrocatalytic performance in the oxygen evolution reaction(OER).In this study,a Py@Co-MOF composite material based on pyrene(Py)molecul...The poor electrical conductivity of metal-organic frameworks(MOFs)limits their electrocatalytic performance in the oxygen evolution reaction(OER).In this study,a Py@Co-MOF composite material based on pyrene(Py)molecules and{[Co2(BINDI)(DMA)_(2)]·DMA}_(n)(Co-MOF,H4BINDI=N,N'-bis(5-isophthalic acid)naphthalenediimide,DMA=N,N-dimethylacetamide)was synthesized via a one-pot method,leveragingπ-πinteractions between pyrene and Co-MOF to modulate electrical conductivity.Results demonstrate that the Py@Co-MOF catalyst exhibited significantly enhanced OER performance compared to pure Co-MOF or pyrene-based electrodes,achieving an overpotential of 246 mV at a current density of 10 mA·cm^(-2) along with excellent stability.Density functional theory(DFT)calculations reveal that the formation of O*in the second step is the rate-determining step(RDS)during the OER process on Co-MOF,with an energy barrier of 0.85 eV due to the weak adsorption affinity of the OH*intermediate for Co sites.CCDC:2419276.展开更多
Graphene/copper-based composite heat sinks demonstrate extensive application potential in military equipment thermal management,high-power electronic packaging,new energy vehicles,and 5G communication systems,due to t...Graphene/copper-based composite heat sinks demonstrate extensive application potential in military equipment thermal management,high-power electronic packaging,new energy vehicles,and 5G communication systems,due to their outstanding properties,including high thermal conductivity,tunable thermal expansion coefficients,excellent mechanical strength,and low density.However,the industrial-scale application of these composites faces critical challenges during the fabrication of components with complex structures,such as inhomogeneous dispersion of graphene within the copper matrix and poor interfacial bonding between the two phases,which substantially undermine the overall performance of graphene/copper-based composites.To address these issues,the preparation methods for graphene/copper-based composite heat sinks were reviewed.For each method,a rigorous analysis was presented to clarify its inherent advantages and unavoidable restrictions.Furthermore,the latest research progress in addressing three core scientific challenges was synthesized,including uniform dispersion of graphene,interfacial optimization mechanisms,and molecular dynamics simulations for elucidating the structure-property relationships.Finally,the future development directions of graphene/copper-based composite heat sinks in engineering applications were prospected.展开更多
Traditional dynamic analysis of mechanical structures,often limited to individual beams or plates,fails to fully capture their dynamic behaviors.In systems where space and mass are constrained,such as the battery supp...Traditional dynamic analysis of mechanical structures,often limited to individual beams or plates,fails to fully capture their dynamic behaviors.In systems where space and mass are constrained,such as the battery support structures in electric aircraft,conventional absorbers and isolators are insufficient for effective vibration control.This study simplifies the battery support structure of electric aircraft as an integrated composite beam consisting of three interconnected beams,and investigated its structural dynamics properties and nonlinear vibration control under thermal conditions caused by battery heat.The nonlinear vibration control is performed using the Nitinol steel wire ropes(Ni Ti-ST),with nonlinear damping properties.The natural frequencies of system are determined using the Rayleigh-Ritz technique.Theoretical results are validated through both Finite Element Method(FEM)and hammer tests.Moreover,the dynamic equations are derived using the Lagrange method and discretized via the Galerkin Truncation Method(GTM).The Harmonic Balance Method(HBM)is used to evaluate the vibration responses of the integrated model,with further verification through the Runge-Kutta Method(RKM).The experiments are conducted to corroborate the theoretical analysis.The results show that the system frequency changes in stages with the increase of the stiffness of the integrated composite beam connection.Especially in the case of varying environments,as the temperature increases,the frequency of system will first increase to a certain maximum value and then gradually decrease.Furthermore,the NiTi-ST effectively reduces vibration in the integrated composite beam,particularly under varying temperatures and external excitations.展开更多
This work addresses optimality aspects related to composite laminates having layers with different orientations.RegressionNeuralNetworks can model the mechanical behavior of these laminates,specifically the stressstra...This work addresses optimality aspects related to composite laminates having layers with different orientations.RegressionNeuralNetworks can model the mechanical behavior of these laminates,specifically the stressstrain relationship.If this model has strong generalization ability,it can be coupled with a metaheuristic algorithm–the PSO algorithm used in this article–to address an optimization problem(OP)related to the orientations of composite laminates.To solve OPs,this paper proposes an optimization framework(OFW)that connects the two components,the optimal solution search mechanism and the RNN model.The OFW has two modules:the search mechanism(Adaptive Hybrid Topology PSO)and the Prediction and Computation Module(PCM).The PCM undertakes all the activities concerning the OP at hand:the stress-strain model,constraints checking,and computation of the objective function.Two case studies about the layers’orientations of laminated specimens are conducted to validate the proposed framework.The specimens belong to“Off-axis oriented specimens”and are subjects of two OPs.The algorithms for AHTPSO and for the two PCMs(one for each problem)are proposed and implemented by MATLAB scripts and functions.Simulations are carried out for different initial conditions.The solutions demonstrated that the OFW is effective and has a highly acceptable computational complexity.The limitation of using the OFWis the generalization ability of the RNN model or any other regression models.To harness the RNN model efficiently,it must have a very good generalization power.If this condition ismet,the OFWcan be integrated into any design process to make optimal choices of the layers’orientations.展开更多
The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solutio...The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solution were used to regulate the microstructure,mechanical properties,and corrosion properties of B_(4)C/TC4 composite.Results show that with the increase in temperature from 500℃to 800°C,partial lamellarα-Ti in the as-deposited sample is gradually transformed into equiaxedα-Ti,accompanied by the disappearance of basketweave microstructure.At 1100°C,a small portion of TiC phase suffers fusion.This composite exhibits the optimal combination of strength and plasticity after annealing at 500℃for 4 h followed by furnace cooling,which is attributed to the stress release effect and the refined basketweave microstructure.However,this composite shows a decline in corrosion resistance after various heat treatments due to grain coarsening and micro-galvanic corrosion.展开更多
In this study,using 3,5‑di(3′,5′‑dicarboxylphenyl)‑1H‑1,2,4‑triazole(H4L)as ligands,a gadolinia‑based organic framework complex{[GdNa(L)(H_(2)O)3]·2H_(2)O}_(n)(Gd‑Na‑MOF)was successfully designed and synthesize...In this study,using 3,5‑di(3′,5′‑dicarboxylphenyl)‑1H‑1,2,4‑triazole(H4L)as ligands,a gadolinia‑based organic framework complex{[GdNa(L)(H_(2)O)3]·2H_(2)O}_(n)(Gd‑Na‑MOF)was successfully designed and synthesized by hydrothermal method.The structure and properties were systematically characterized and tested by techniques such as single‑crystal X‑ray diffraction,powder X‑ray diffraction,thermogravimetric analysis,infrared spectroscopy,and fluorescence spectroscopy.The results indicate that this complex has a unique 3D structure,excellent thermal stability,and outstanding luminescent performance.Based on its luminescent properties,a polymer‑embedding method was employed to fabricate the Gd‑Na‑MOF into a flexible,washable composite fluorescent film,Gd‑Na‑MOF@PMMA/BMA(PMMA=polymethyl methacrylate,BMA=butyl methacrylate).This fluorescent film exhibited highly sensitive recognition capability for tyramine,with a low detection limit of 1.66μmol·L^(-1).It was used for the detection of tyramine in bananas,with a recovery rate of 96.92%‑100.26%.CCDC:2466949.展开更多
Single-crystal(SC) structures have long been regarded as the optimal configuration for metal halide perovskite photodetectors(PDs);however, their applications in large-area imaging and wearable electronics face limita...Single-crystal(SC) structures have long been regarded as the optimal configuration for metal halide perovskite photodetectors(PDs);however, their applications in large-area imaging and wearable electronics face limitations due to size constraints and mechanical inflexibility. To address these challenges, this study develops a hybrid composite structure— polycrystalline powder(PCP) matrix(PCPM)—by strategically homogenizing 20 μm PCPs within a poly(methyl methacrylate) matrix. Such a configuration enables the formation of densely packed PCP microstructures while maintaining electric conductivity and mechanical flexibility. In the single-photon regime, responsivity(R) and external quantum efficiency(EQE) decline by 50%, with concurrent 3–4-fold enhancements in the On/Off ratio and 12–16-fold improvements in specific detectivity(D), compared with those of SC counterparts. Notably, in the two-photon regime, R and EQE exhibit a 2–3-fold increase, and the On/Off ratio and D exhibit 12–16-fold improvements. The PCPM configuration enables the high-repetitionrate wafer-scale fabrication of active layers for imaging PDs and provides exceptional mechanical flexibility and self-recovery. These findings establish PCPMs as a scalable platform for next-generation perovskite wearable electronics.展开更多
基金supported by National Natural Science Foundation of China(No.52204302)Young Elite Scientist Sponsorship Program by CAST(No.YESS20220533)Hunan Provincial Natural Science Foundation of China(No.2022JJ40625).
文摘The isothermal oxidation kinetics of vanadium–titanium magnetite(VTM)pellets prepared with 3Co-binder(coal-based colloidal composite binder)and F-binder(pulverized Funa binder)are compared.The oxidation process was analyzed using the first-order irreversible reaction,following the shrinking unreacted nucleus model.The results demonstrate that VTM pellets prepared with 3Co-binder exhibit a faster oxidation rate than those with F-binder across the temperatures ranging from 1073 to 1473 K.In both cases,the oxidation process was controlled by an interfacial chemical reaction during the pre-oxidation stage and by internal diffusion during the mid-oxidation stage.The type of binder did not influence the primary oxidation control mechanism of the VTM pellets.However,the apparent rate constants in the pre-oxidation stage and the internal diffusion coefficients in the mid-oxidation stage were higher for pellets with 3Co-binder compared to those with F-binder.The apparent activation energies for the 3Co-binder pellets were similar to those of bentonite,indicating favorable kinetic conditions without negative impacts on the oxidation process.Nonetheless,it is important to note that pellets with F-binder required a longer oxidation time than those with 3Co-binder.
基金Project (11JK0799) supported by Scientific Research Program Funded by Shaanxi Provincial Education Department,ChinaProject (KTCQ1-17) supported by Scientific and Technological Innovation and Co-ordination Funded by Science and Technology Department of Shaanxi Province,China
文摘Using titanium wires （99.5%, 200 μm in diameter） as a reactive source, an Al-based composite coating reinforced by titanium tri-aluminide （A13Ti） particles was fabricated by infiltration plus in-situ methods. According to the differential thermal analysis （DTA） curve, the reactive temperature between Ti wires and A1 matrix can be determined at 890 ℃. The obtained composite coatings were characterized by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, and microhardness and wear test. The experimental results show that when holding period is 20 min at 890℃, the titanium wires react completely to in-situ synthesize Al3Ti particles, which presents blocky and strip-like states. The microhardness of in-situ synthesized Al3Ti particles is about 4.5 times that of the Al-matrix. Under the condition of dry sliding at 10 N load, compared with the unreinforced Al matrix, the composite coating fabricated with 20 min offers unique wear resistance behavior, and its wear mechanism is that the adhesive wear and abrasive wear coexist.
基金Project (2012CB619600) supported by the Ministry of Science and Technology of ChinaProject (51201047) supported by the National Natural Science Foundation of China+1 种基金Project (HIT.NSRIF.2013001) supported by the Fundamental Research Funds for the Central Universities ChinaProject (20110491038) supported by the Postdoctoral Science Foundation of China
文摘The in-situ Al-based composites with different SiO2/C/Al molar ratios were fabricated by reaction hot pressing. The dry sliding wear characteristics of the composites were investigated using a pin-on-disc wear tester. Scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) were used to investigate the surface composition and its morphology. The results show that when the SiO2/C/Al molar ratio is 3:6:9, more in-situ synthesized Al2O3 and SiC along with Si particles are produced, and Al4C3 is prevented completely from the Al?SiO2?C system. Thereby, a significant improvement of wear resistance is obtained. When the sliding velocity increases from 0.4 to 1.6 m/s, the wear loss decreases gradually. With increasing the normal load, the wear loss increases as well. Ploughing, craters and micro-grooving are observed as dominant abrasive wear mechanisms. Whereas, when a high velocity is employed, only the oxidation mechanism controls the wear behavior of the composites.
基金financially supported by the Science and Technology Plan Item of Liaoning Province (No.201601174)the National Natural Science Foundation of China (No.51371121)
文摘An Al-based composite reinforced with core–shell-structured Ti/Al_3Ti was fabricated through a powder metallurgy route followed by hot extrusion and was found to exhibit promising mechanical properties. The ultimate tensile strength and elongation of the composite sintered at 620°C for 5 h and extruded at a mass ratio of 12.75:1 reached 304 MPa and 14%, respectively, and its compressive deformation reached 60%. The promising mechanical properties are due to the core–shell-structured reinforcement, which is mainly composed of Al_3Ti and Ti and is bonded strongly with the Al matrix, and to the reduced crack sensitivity of Al_3Ti. The refined grains after hot extrusion also contribute to the mechanical properties of this composite. The mechanical properties might be further improved through regulating the relative thickness of Al–Ti intermetallics and Ti metal layers by adjusting the sintering time and the subsequent extrusion process.
基金supported financially by the National Natural Science Foundation of China(Nos.51505459 and 51675510)the National Basic Research Program of China(No.2013CB632300)
文摘TiAl-based composites reinforced with different high volume fractions of nearly network TizAIC phase have been successfully prepared by mechanical alloying and hot-pressing method.Their microstructure.mechanical and tribological properties have been investigated.Ti2AIC network becomes continuous but the network wall grows thicker with increasing the Ti2AIC content.The continuity and wall size of the network Ti2AIC phase exert a significant influence on the mechanical properties.The bending strength of the composites first increases and then decreases with the Ti2A1C content.The compressive strength of the composite decreases slightly compared to the TiAI alloy,but the hardness is enhanced.Due to the high hardness and load-carrying capacity of the network structure,these composites have the better wear resistance.And this enhancement is more notable at low applied loads and high Ti2A1C content.The mechanisms simulating the role of network Ti2AIC phase on the wear behavior and the wear process of TiAl/Ti2AIC composites at different applied loads have been proposed.
文摘Mechanically alloyed NiAl-TiB_2-Y_2O_3 composite (volume percentage of dispersoids about 15v%) was prepared by hot pressing. The compressive properties of the composite from 300 K to 1360 K were tested and the microstructures were studied mainly by TEM. The yield strengths of the composite at room temperature and high temperatures are considerably higher than that of monolithic NiAl and also is higher than similar NiAl-based composites which contained higher content of dispersoids but showed coarser microstructure. The possible strengthening mechanisms working in the composite are discussed.
基金supported by the National Natural Science Foundation of China(Grant Nos.51131006,51071151)
文摘A new Al-based composite consisting of submicron-sized α-Al matrix embedded with precipitated intermetallic phases was developed by controlling the devitrification process of an Al-Ni-Y-Co-La amorphous alloy.Such a homogeneous composite structure presented an ultrahigh strength of about 1.34 GPa and a large compressive plastic strain up to 22%.The unique mechanical properties during compression are mainly attributed to the dislocation slip deformation of ductile a-AI matrix and the shear-induced refinement of strengthening intermetallic phases.
文摘An aluminium alloy and its composite with dispersed SiC particles made by liquid metallurgy route were extruded under optimized conditions.The properties were characterized in terms of microstructure,hardness and sliding wear behaviour and then compared between the extruded and cast alloys and composites,in order to understand the benefits of composite and extrusion on the alloy.It was observed that composites drastically increased the hardness and the extruded composites further increased this value.The advantage of composites was realized in sliding wear tests.
基金Project(51174244) supported by the National Natural Science Foundation of ChinaProject(CDJZR11130005) supported by the Fundamental Research Funds for the Central Universities,China
文摘An aluminum-based in-situ composites reinforced with Mg2Si and Si particles were produced by centrifugal casting A1-20Si-5Mg alloy. The microstructure of the composites was examined, and the effects of temperature on fracture behavior of the composite were investigated. The results show that the average fraction of primary Si and Mg2Si particles in the composites is as high as 38%, and ultimate tensile strengths （UTS） of the composites first increase then decrease with the increase of test temperature. Microstructures of broken specimens show that both the particle fracture and the interface debonding affect the fracture behavior of the composites, and the interface debonding becomes the dominant fracture mechanism with increasing test temperature. Comparative results indicate that rich particles in the composites and excellent interface strength play great roles in enhancing tensile property by preventing the movement of dislocations.
基金Supported by the National Natural Science Foundation of China(Nos.52293472,22473096 and 22471164)。
文摘Among various architectures of polymers,end-group-free rings have attracted growing interests due to their distinct physicochemical performances over the linear counterparts which are exemplified by reduced hydrodynamic size and slower degradation.It is key to develop facile methods to large-scale synthesis of polymer rings with tunable compositions and microstructures.Recent progresses in large-scale synthesis of polymer rings against single-chain dynamic nanoparticles,and the example applications in synchronous enhancing toughness and strength of polymer nanocomposites are summarized.Once there is the breakthrough in rational design and effective large-scale synthesis of polymer rings and their functional derivatives,a family of cyclic functional hybrids would be available,thus providing a new paradigm in developing polymer science and engineering.
基金supported by the National Science Foundation for Distinguished Young Scholars of China(No.52325506)the Fundamental Research Funds for the Central Universities(No.DUT22LAB501)。
文摘Ultrasonic-Assisted Grinding(UAG)is a novel manufacturing technology that shows promising promise for use in processing Ceramic Matrix Composites(CMCs).Nevertheless,analyzing the material removal process of CMCs with multidirectional structure during UAG is challenging,impeding the progress and improvement of the UAG process.This work examined the impact of ultrasonic vibration on the dynamic mechanical characteristics during processing.Additionally,we experimentally elucidated the material removal mechanism of CMCs during the scratching process under the influence of vertical vibration.The results indicate that the introduction of ultrasonic vibration causes a strain rate effect,resulting in a modification of the material removal mechanism,subsequently impacting the processing quality.Ultrasonic vibration increases the dynamic strength and brittleness of the fibers in CMCs,leading to more cracks at fracture,which changes from the original bending fracture to shear fracture.In addition,ultrasonic vibration can effectively inhibit the impact of scratching depth and anisotropy on the removal mechanism of CMCs,resulting in a more uniform surface of CMCs after processing.
文摘A composite electrocatalyst,CoMoNiO-S/NF-110(NF is nickel foam),was synthesized through electrodeposition,followed by pyrolysis and then the vulcanization process.CoMoNiO-S/NF-110 exhibited a structure where Ni3S2 and Mo2S3 nanoparticles were integrated at the edges of Co3O4 nanosheets,creating a rich,heterogeneous interface that enhances the synergistic effects of each component.In an alkaline electrolyte,the synthesized CoMoNiO-S/NF-110 exhibited superior electrocatalytic performance for oxygen evolution reaction(OER),achieving current densities of 100 and 200 mA·cm^(-2) with low overpotentials of 199.4 and 224.4 mV,respectively,outperforming RuO2 and several high-performance Mo and Ni-based catalysts.This excellent performance is attributed to the rich interface formed between the components and active sites exposed by the defect structure.
基金Supported by the Autonomous Research Project of SKLCC(2024BWZ003)Strategic Priority Research Program of the Chinese Academy of Sciences(XDA0390401)the Doctoral Research Start-up Funding of Shanxi Institute of Technology(026012).
文摘KIT-5/Beta composite supports were synthesized using an in situ self-assembly hydrothermal method,and NiW/KIT-5/Beta catalysts were prepared by impregnation.A series of characterization techniques were utilized to evaluate the influence of varying hydrothermal synthesis temperatures on the physicochemical properties of both the KIT-5/Beta supports and the resulting catalysts.The catalytic performances of catalysts were evaluated under reaction conditions of 320℃,4 MPa H_(2)pressure,and a weight hourly space velocity(WHSV)of 4.8 h^(-1)for hydrodenitrogenation(HDN)of quinoline.The results indicated that the specific surface area and pore structure of the materials could be effectively regulated by adjusting the hydrothermal synthesis temperature,which in turn influenced the number of active sites on the catalyst.The NiW/KB-125 catalyst,synthesized at 125℃,presented the highest quinoline HDN efficiency(96.8%),which can be attributed to its favorable pore channel structure,greater Brønsted acid number,higher degree of metal sulfidation(80.12%)and appropriate metal-support interaction(MSI).
文摘The poor electrical conductivity of metal-organic frameworks(MOFs)limits their electrocatalytic performance in the oxygen evolution reaction(OER).In this study,a Py@Co-MOF composite material based on pyrene(Py)molecules and{[Co2(BINDI)(DMA)_(2)]·DMA}_(n)(Co-MOF,H4BINDI=N,N'-bis(5-isophthalic acid)naphthalenediimide,DMA=N,N-dimethylacetamide)was synthesized via a one-pot method,leveragingπ-πinteractions between pyrene and Co-MOF to modulate electrical conductivity.Results demonstrate that the Py@Co-MOF catalyst exhibited significantly enhanced OER performance compared to pure Co-MOF or pyrene-based electrodes,achieving an overpotential of 246 mV at a current density of 10 mA·cm^(-2) along with excellent stability.Density functional theory(DFT)calculations reveal that the formation of O*in the second step is the rate-determining step(RDS)during the OER process on Co-MOF,with an energy barrier of 0.85 eV due to the weak adsorption affinity of the OH*intermediate for Co sites.CCDC:2419276.
基金Research Start-Up Fund Project of Anhui Polytechnic University(S022023017)University Research Project of Anhui Province(2023AH050937)+1 种基金Anhui Polytechnic University Research Foundation for Introducing Talents(2022YQQ003)Anhui Province Key Laboratory of Intelligent Vehicle Chassis by Wire。
文摘Graphene/copper-based composite heat sinks demonstrate extensive application potential in military equipment thermal management,high-power electronic packaging,new energy vehicles,and 5G communication systems,due to their outstanding properties,including high thermal conductivity,tunable thermal expansion coefficients,excellent mechanical strength,and low density.However,the industrial-scale application of these composites faces critical challenges during the fabrication of components with complex structures,such as inhomogeneous dispersion of graphene within the copper matrix and poor interfacial bonding between the two phases,which substantially undermine the overall performance of graphene/copper-based composites.To address these issues,the preparation methods for graphene/copper-based composite heat sinks were reviewed.For each method,a rigorous analysis was presented to clarify its inherent advantages and unavoidable restrictions.Furthermore,the latest research progress in addressing three core scientific challenges was synthesized,including uniform dispersion of graphene,interfacial optimization mechanisms,and molecular dynamics simulations for elucidating the structure-property relationships.Finally,the future development directions of graphene/copper-based composite heat sinks in engineering applications were prospected.
基金supported by the National Natural Science Foundation of China(No.12272240)the Liaoning Revitalization Talents Program,China(No.XLYC2203197)。
文摘Traditional dynamic analysis of mechanical structures,often limited to individual beams or plates,fails to fully capture their dynamic behaviors.In systems where space and mass are constrained,such as the battery support structures in electric aircraft,conventional absorbers and isolators are insufficient for effective vibration control.This study simplifies the battery support structure of electric aircraft as an integrated composite beam consisting of three interconnected beams,and investigated its structural dynamics properties and nonlinear vibration control under thermal conditions caused by battery heat.The nonlinear vibration control is performed using the Nitinol steel wire ropes(Ni Ti-ST),with nonlinear damping properties.The natural frequencies of system are determined using the Rayleigh-Ritz technique.Theoretical results are validated through both Finite Element Method(FEM)and hammer tests.Moreover,the dynamic equations are derived using the Lagrange method and discretized via the Galerkin Truncation Method(GTM).The Harmonic Balance Method(HBM)is used to evaluate the vibration responses of the integrated model,with further verification through the Runge-Kutta Method(RKM).The experiments are conducted to corroborate the theoretical analysis.The results show that the system frequency changes in stages with the increase of the stiffness of the integrated composite beam connection.Especially in the case of varying environments,as the temperature increases,the frequency of system will first increase to a certain maximum value and then gradually decrease.Furthermore,the NiTi-ST effectively reduces vibration in the integrated composite beam,particularly under varying temperatures and external excitations.
基金supported by the Ministry of Research,Innovation and Digitization,CNCS/CCCDI–UEFISCDI(Romania),Nr.11/2024,within PNCDI IV.The APC received no external funding.
文摘This work addresses optimality aspects related to composite laminates having layers with different orientations.RegressionNeuralNetworks can model the mechanical behavior of these laminates,specifically the stressstrain relationship.If this model has strong generalization ability,it can be coupled with a metaheuristic algorithm–the PSO algorithm used in this article–to address an optimization problem(OP)related to the orientations of composite laminates.To solve OPs,this paper proposes an optimization framework(OFW)that connects the two components,the optimal solution search mechanism and the RNN model.The OFW has two modules:the search mechanism(Adaptive Hybrid Topology PSO)and the Prediction and Computation Module(PCM).The PCM undertakes all the activities concerning the OP at hand:the stress-strain model,constraints checking,and computation of the objective function.Two case studies about the layers’orientations of laminated specimens are conducted to validate the proposed framework.The specimens belong to“Off-axis oriented specimens”and are subjects of two OPs.The algorithms for AHTPSO and for the two PCMs(one for each problem)are proposed and implemented by MATLAB scripts and functions.Simulations are carried out for different initial conditions.The solutions demonstrated that the OFW is effective and has a highly acceptable computational complexity.The limitation of using the OFWis the generalization ability of the RNN model or any other regression models.To harness the RNN model efficiently,it must have a very good generalization power.If this condition ismet,the OFWcan be integrated into any design process to make optimal choices of the layers’orientations.
基金Tianjin Municipal Natural Science Foundation(23JCYBJC00040)National Natural Science Foundation of China(52175369)。
文摘The TiB+TiC dual-reinforced B_(4)C/TC4 composite was in-situ fabricated via incorporating 0.5wt%B_(4)C reinforcement during the laser melting deposition process.Different heat treatments of annealing and solid solution were used to regulate the microstructure,mechanical properties,and corrosion properties of B_(4)C/TC4 composite.Results show that with the increase in temperature from 500℃to 800°C,partial lamellarα-Ti in the as-deposited sample is gradually transformed into equiaxedα-Ti,accompanied by the disappearance of basketweave microstructure.At 1100°C,a small portion of TiC phase suffers fusion.This composite exhibits the optimal combination of strength and plasticity after annealing at 500℃for 4 h followed by furnace cooling,which is attributed to the stress release effect and the refined basketweave microstructure.However,this composite shows a decline in corrosion resistance after various heat treatments due to grain coarsening and micro-galvanic corrosion.
文摘In this study,using 3,5‑di(3′,5′‑dicarboxylphenyl)‑1H‑1,2,4‑triazole(H4L)as ligands,a gadolinia‑based organic framework complex{[GdNa(L)(H_(2)O)3]·2H_(2)O}_(n)(Gd‑Na‑MOF)was successfully designed and synthesized by hydrothermal method.The structure and properties were systematically characterized and tested by techniques such as single‑crystal X‑ray diffraction,powder X‑ray diffraction,thermogravimetric analysis,infrared spectroscopy,and fluorescence spectroscopy.The results indicate that this complex has a unique 3D structure,excellent thermal stability,and outstanding luminescent performance.Based on its luminescent properties,a polymer‑embedding method was employed to fabricate the Gd‑Na‑MOF into a flexible,washable composite fluorescent film,Gd‑Na‑MOF@PMMA/BMA(PMMA=polymethyl methacrylate,BMA=butyl methacrylate).This fluorescent film exhibited highly sensitive recognition capability for tyramine,with a low detection limit of 1.66μmol·L^(-1).It was used for the detection of tyramine in bananas,with a recovery rate of 96.92%‑100.26%.CCDC:2466949.
基金supported by the Key Project of the National Key R&D Program of China (Grant No.2022YFA1404500)the National Natural Science Foundation of China (Grant Nos.12434017,62005183)the Guangdong Basic and Applied Basic Research Foundation (Grant No.2025A1515010329)。
文摘Single-crystal(SC) structures have long been regarded as the optimal configuration for metal halide perovskite photodetectors(PDs);however, their applications in large-area imaging and wearable electronics face limitations due to size constraints and mechanical inflexibility. To address these challenges, this study develops a hybrid composite structure— polycrystalline powder(PCP) matrix(PCPM)—by strategically homogenizing 20 μm PCPs within a poly(methyl methacrylate) matrix. Such a configuration enables the formation of densely packed PCP microstructures while maintaining electric conductivity and mechanical flexibility. In the single-photon regime, responsivity(R) and external quantum efficiency(EQE) decline by 50%, with concurrent 3–4-fold enhancements in the On/Off ratio and 12–16-fold improvements in specific detectivity(D), compared with those of SC counterparts. Notably, in the two-photon regime, R and EQE exhibit a 2–3-fold increase, and the On/Off ratio and D exhibit 12–16-fold improvements. The PCPM configuration enables the high-repetitionrate wafer-scale fabrication of active layers for imaging PDs and provides exceptional mechanical flexibility and self-recovery. These findings establish PCPMs as a scalable platform for next-generation perovskite wearable electronics.
