A non-isothermal injection molding process for a non-Newtonian viscous pseudoplastic fluid is simulated.A conservative interface capturing technique and the flow field solving method are coupled to perform a dynamic s...A non-isothermal injection molding process for a non-Newtonian viscous pseudoplastic fluid is simulated.A conservative interface capturing technique and the flow field solving method are coupled to perform a dynamic simulation.The validity of the numerical method is verified by a benchmark problem.The melt interface evolution versus time is captured and the physical quantities such as temperature,velocity and pressure at each time step are obtained with corresponding analysis.A"frozen skin"layer with the thickness increasing versus time during the injection process is found.The fact that the"frozen skin"layer can be reduced by increasing the injection velocity is numerically verified.The fountain flow phenomenon near the melt interface is also captured.Moreover,comparisons with the non-isothermal Newtonian case show that the curvatures of the interface arcs and the pressure contours near the horizontal mid-line of the cavity for the non-Newtonian pseudoplastic case is larger than that for the Newtonian case.The velocity profiles are different at different positions for the non-Newtonian pseudoplastic case,while in the case of Newtonian flow the velocity profiles are parabolic and almost the same at different positions.展开更多
In actual power systems,most of the high-voltage buses of the transformers are zero injection buses without load or generation.Power injections into these buses are strictly 0,so based on Kirchhoff's current law(K...In actual power systems,most of the high-voltage buses of the transformers are zero injection buses without load or generation.Power injections into these buses are strictly 0,so based on Kirchhoff's current law(KCL),equality constraints should be used to handle these buses in a state estimation model.It is a challenge to ensure that these zero injection constraints can be strictly satisfied without losing computational efficiency.展开更多
A fast explicit finite difference method (FEFDM),derived from the differential equations of one-dimensional steady pipe flow,was presented for calculation of wellhead injection pressure.Recalculation with a traditiona...A fast explicit finite difference method (FEFDM),derived from the differential equations of one-dimensional steady pipe flow,was presented for calculation of wellhead injection pressure.Recalculation with a traditional numerical method of the same equations corroborates well the reliability and rate of FEFDM.Moreover,a flow rate estimate method was developed for the project whose injection rate has not been clearly determined.A wellhead pressure regime determined by this method was successfully applied to the trial injection operations in Shihezi formation of Shenhua CCS Project,which is a good practice verification of FEFDM.At last,this method was used to evaluate the effect of friction and acceleration terms on the flow equation on the wellhead pressure.The result shows that for deep wellbore,the friction term can be omitted when flow rate is low and in a wide range of velocity the acceleration term can always be deleted.It is also shown that with flow rate increasing,the friction term can no longer be neglected.展开更多
The simulation of three-dimensional （3D） non-isothermal, non-Newtonian fluid filling process is an extremely difficult task and remains a challenging problem, which includes polymer melt flow with free surface coupl...The simulation of three-dimensional （3D） non-isothermal, non-Newtonian fluid filling process is an extremely difficult task and remains a challenging problem, which includes polymer melt flow with free surface coupled with transient heat transfer. This paper presents a full 3D non-isothermal two-phase flow model to predict the complex flow in melt filling process, where the Cross-WLF model is applied to characterize the rheological behav- ior of polymer melt. The governing equations are solved using finite volume method with SIMPLEC algorithm on collocated grids and the melt front is accurately captured by a high resolution level set method. A domain exten- sion technique is adopted to deal with the complex cavities, which greatly reduces the computational burden. To verify the validity of the developed 3D approach, the melts filling processes in two thin rectangular cavities （one of them with a cylindrical insert） are simulated. The predicted melt front interfaces are in good agreement with the experiment and commercial software prediction. For a case with a rather complex cavity, the dynamic filling process in a hemispherical shell is successfully simulated. All of the numerical results show that the developed numerical procedure can provide a reasonable orediction for injection molding process.展开更多
The oil oxidation characteristics of the whole temperature regions from 30 ℃ to 600 ℃ during oil reservoir air injection were revealed by experiments. The whole oil oxidation temperature regions were divided into fo...The oil oxidation characteristics of the whole temperature regions from 30 ℃ to 600 ℃ during oil reservoir air injection were revealed by experiments. The whole oil oxidation temperature regions were divided into four different parts: dissolving and inflation region, low temperature oxidation region, medium temperature oxidation region and high temperature oxidation region. The reaction mechanisms of different regions were explained. Based on the oil oxidation characteristics and filed tests results, light oil reservoirs air injection development methods were divided into two types: oxygen-reducing air flooding and air flooding;heavy oil reservoirs air injection in-situ combustion development methods were divided into two types: medium temperature in-situ combustion and high temperature in-situ combustion. When the reservoir temperature is lower than 120 ℃, oxygen-reducing air flooding should be used for light oil reservoir development. When the reservoir temperature is higher than 120 ℃, air flooding method should be used for light oil reservoir development. For a normal heavy oil reservoir, when the combustion front temperature is lower than 400 ℃, the development method is medium temperature in-situ combustion. For a heavy oil reservoir with high oil resin and asphalting contents, when the combustion front temperature is higher than 450 ℃, the development method at this condition is high temperature in-situ combustion. Ten years field tests of air injection carried out by PetroChina proved that air has advantages in technical, economical and gas source aspects compared with other gas agents for oilfield gas injection development. Air injection development can be used in low/super-low permeability light oil reservoirs, medium and high permeability light oil reservoirs and heavy oil reservoirs. Air is a very promising gas flooding agent.展开更多
A diagnostic signal current trace detecting based single phase-to-ground fault line identifica- tion and section location method for non-effectively grounded distribution systems is presented in this paper.A special d...A diagnostic signal current trace detecting based single phase-to-ground fault line identifica- tion and section location method for non-effectively grounded distribution systems is presented in this paper.A special diagnostic signal current is injected into the fault distribution system,and then it is detected at the outlet terminals to identify the fault line and at the sectionalizing or branching point along the fault line to locate the fault section.The method has been put into application in actual distribution network and field experience shows that it can identify the fault line and locate the fault section correctly and effectively.展开更多
As we all know, cyclic gas injection is one of the most effective development methods to improve condensate oil recovery. When dealing with the calculation of the reserves, the injection-production differences and wat...As we all know, cyclic gas injection is one of the most effective development methods to improve condensate oil recovery. When dealing with the calculation of the reserves, the injection-production differences and water influx create great influence on the accuracy. Based on the existing research, we proposed a new material balance equation which considered the differences of composition between produced and injected fluids and the effect of water influx, and a solution was provided in this paper. The results of the method are closer to the actual situation because they are built on the law of conservation of mass, and the using of curve fitting method can not only avoid the use of water influx coefficient but also obtain the water influx rate and reserves at the same time. The YH-23 gas condensate reservoir is taking as a typical subject to do the research, which has been exploited by cycle gas injection for 14 years. Three different methods are used to calculate the reserves, and the results show that the method proposed in this paper has minimum error of 2.96%.展开更多
The north anchorage caisson of Taizhou Bridge encountered some difficulties during the sinking process for the large sidewall frictional resistances. To solve this problem, a new concept and method called subsidence m...The north anchorage caisson of Taizhou Bridge encountered some difficulties during the sinking process for the large sidewall frictional resistances. To solve this problem, a new concept and method called subsidence method aided by water injection is proposed. Numeral analysis is adopted to simulate the effects of this method for the north anchor of Taizhou Bridge, which confirmed the feasibility and validity. Finally, the method is applied to the north anchor caisson during the caisson sinking procedure and helps the caisson sink and embed to the designed position smoothly.展开更多
There are the application scope limits for single differential-mode current injection test method, so in order to carry out injection susceptibility test for two-pieces equipment interconnected with both ends of a cab...There are the application scope limits for single differential-mode current injection test method, so in order to carry out injection susceptibility test for two-pieces equipment interconnected with both ends of a cable simultaneously, a double differential-mode current in- jection test method (DDMCI) is proposed. The method adopted the equivalence source wave theorem and Baum-Liu-Tesche(BLT) equation as its theory foundation. The equivalent corresponding relation between injection voltage and radiation electric field intensity is derived, and the phase relation between the two injection voltage sources is confirmed. The results indicate that the amplitude and phase of the equivalent injection voltage source is closely related to the S parameter of directional coupling device, the transmission line length, and the source vector in BLT equation, but has nothing to do with the reflection coefficient between the two equipment pieces. Therefore, by choosing the right amplitude and phase of the double injection voltage sources, the DDMCI test is equivalent to the radiation test for two interconnected equipment of a system.展开更多
OBJECTIVE: To compare the clinical effect of brachial plexus block with "One Injection Two Points" guided under ultrasound and the conventional method guiding by ultrasound. METHODS: 70 patients were randomi...OBJECTIVE: To compare the clinical effect of brachial plexus block with "One Injection Two Points" guided under ultrasound and the conventional method guiding by ultrasound. METHODS: 70 patients were randomized evenly into 2 groups, with 35 patients in each group, while the Experiment Group(Group B) received One Injection Two Points" method, the Control Group(Group A) received the conventional method.The nerve block every 5 s, the success rate of anesthesia, the dosage of local anesthetics, second remedial anesthesia, adverse reactions, etc.were recorded. RESULTS: Group B was superior to group A in the success rate of anesthesia; There were 6 patients in group A who required constant pump injection of Remifentanil to remedy, while no patients in Group B needed remedy treatment. There were no serious adverse reactions in both groups.CONCLUSIONS: The clinical effect of brachial plexus block with "One Injection Two Points" method guided under ultrasoundguiding by ultrasound was superior to that of the conventional method.展开更多
Compared with the middle-shallow shale gas reservoirs,deep shale formation often reveals lower fracture complexity,smaller effective stimulated volumes,lower conductivity,and faster declined when the same injection mo...Compared with the middle-shallow shale gas reservoirs,deep shale formation often reveals lower fracture complexity,smaller effective stimulated volumes,lower conductivity,and faster declined when the same injection model and technical parameters were used.Therefore,it is necessary to research a special injection model for the deep shale formation.In this paper,a series of laboratory stimulated experiments were carried to analyze the injection method on hydraulic fracturing initiation and propagation in the deep shale formation.The outcrop shale of Longmaxi formation in Sichuan Basin was selected and three different injection methods(constant,stepped-rise and cyclic progressive uplift pump rate)were used in these experiments.The test results showed that the stepped-rise pump rate is conductive to opening the pre-existing natural fracture and bedding planes,the fracture complexity of this injection method is the highest.Meanwhile,the fracturing pressure and total injection volume are the lowest.In contrast,the cyclic-uplift injection method can only form a transverse fracture,and the fracturing pressure is the highest.The research results have an important theoretical guiding value for deep shale hydraulic fracturing operation.展开更多
Injection pressure is one of the key parameters used in the design of shale gas reservoir stimulation.Higher injection pressure helps to initiate fractures,inject fracturing fluid and proppant smoothly and maximize th...Injection pressure is one of the key parameters used in the design of shale gas reservoir stimulation.Higher injection pressure helps to initiate fractures,inject fracturing fluid and proppant smoothly and maximize the stimulated reservoir volume as soon as possible.If the injection pressure is too high,however,the risk of casing deformation is increased significantly.In this paper,the numerical calculation format of the injection pressure safety window while ensuring casing integrity(i.e.,the maximum safety injection pressure)was proposed based on an example of an actual engineering project.Then,it was verified based on the actual situation of one shale gas well in Weiyuan.The numerical calculation format is as follows.First,a 3D finite element model of initial fine geostress field is established in the scale of block.Second,a primary submodel for introducing the asymmetric characteristics of reservoir stiffness to simulate the asymmetry of fracture distribution.Third,a secondary submodel containing the attributes of casing,cement sheath and reservoir material properties.Fourth,submodels are used to calculate the casing deformation generated by different injection loads and estimate the maximum allowable fracturing injection pressure(pj)while the safety requirement of casing deformation is satisfied.The calculation result of the case well shows that when the cementing quality is poor and fractures are distributed asymmetrically,the lateral and vertical displacements at the maximum displacement point of the casing under the injection pressure of 80 MPa are obviously lower than those under 90 MPa.According to the yield limit criterion of P-110 casing steel,the casing deformation in this case is elastic strain,so the injection pressure of 80 MPa is safe.In conclusion,this method has rational precision and accuracy,for its numerical result is consistent with the actual engineering phenomenon.展开更多
Characteristics of heat transfer and flow of Newtonian and non-Newtonian fluids through porous walls and in porous media are studied due to their wide range of applications including geothermal reservoirs,heat exchang...Characteristics of heat transfer and flow of Newtonian and non-Newtonian fluids through porous walls and in porous media are studied due to their wide range of applications including geothermal reservoirs,heat exchangers,marine propulsion,and aerodynamics.The current study investigates the characteristics of heat transport in a reactive third-grade fluid,moving through permeable parallel plates,with uniform suction/injection velocity.The two permeable,parallel plates are maintained at the same,constant temperature.After being transformed into its dimensionless equivalent,governing equations are solved by employing the Least Squares Method(LSM).The LSM results are further validated with numerical solutions for temperature and velocity.The impact of cross-flow Reynolds number,Peclet number,heat generation parameter,non-Newtonian parameter,and Brinkman number on entropy generation,velocity,temperature,and Bejan number are investigated.Theresults indicate that temperature distribution is significantly influenced by the third-grade fluid parameter.The maximum temperature drops from almost 0.12 to 0.10 as the third-grade fluid parameter increases from0.05 to 0.4.When the cross-flow Reynolds number is raised from 0.05 to 3,the maximum temperature drops from 0.12 to around 0.09.Temperature is strongly influenced by the heat generation parameter.A greater understanding of the thermal characteristics necessary for the design of a variety of systems,such as heat exchangers,marine propulsion,aerodynamic systems,etc.,may be gained from the findings of the current study.展开更多
基金Supported by the National Natural Science Foundation of China（10871159） the National Basic Research Program of China（2005CB321704）
文摘A non-isothermal injection molding process for a non-Newtonian viscous pseudoplastic fluid is simulated.A conservative interface capturing technique and the flow field solving method are coupled to perform a dynamic simulation.The validity of the numerical method is verified by a benchmark problem.The melt interface evolution versus time is captured and the physical quantities such as temperature,velocity and pressure at each time step are obtained with corresponding analysis.A"frozen skin"layer with the thickness increasing versus time during the injection process is found.The fact that the"frozen skin"layer can be reduced by increasing the injection velocity is numerically verified.The fountain flow phenomenon near the melt interface is also captured.Moreover,comparisons with the non-isothermal Newtonian case show that the curvatures of the interface arcs and the pressure contours near the horizontal mid-line of the cavity for the non-Newtonian pseudoplastic case is larger than that for the Newtonian case.The velocity profiles are different at different positions for the non-Newtonian pseudoplastic case,while in the case of Newtonian flow the velocity profiles are parabolic and almost the same at different positions.
文摘In actual power systems,most of the high-voltage buses of the transformers are zero injection buses without load or generation.Power injections into these buses are strictly 0,so based on Kirchhoff's current law(KCL),equality constraints should be used to handle these buses in a state estimation model.It is a challenge to ensure that these zero injection constraints can be strictly satisfied without losing computational efficiency.
基金Project(Z110803)supported by the State Key Laboratory of Geomechanics and Geotechnical Engineering,ChinaProject(2008AA062303)supported by the National High Technology Research and Development Program of China
文摘A fast explicit finite difference method (FEFDM),derived from the differential equations of one-dimensional steady pipe flow,was presented for calculation of wellhead injection pressure.Recalculation with a traditional numerical method of the same equations corroborates well the reliability and rate of FEFDM.Moreover,a flow rate estimate method was developed for the project whose injection rate has not been clearly determined.A wellhead pressure regime determined by this method was successfully applied to the trial injection operations in Shihezi formation of Shenhua CCS Project,which is a good practice verification of FEFDM.At last,this method was used to evaluate the effect of friction and acceleration terms on the flow equation on the wellhead pressure.The result shows that for deep wellbore,the friction term can be omitted when flow rate is low and in a wide range of velocity the acceleration term can always be deleted.It is also shown that with flow rate increasing,the friction term can no longer be neglected.
基金Supported by the National Basic Research Program of China(2012CB025903)the National Natural Science Foundation of China(91434201,11402210)
文摘The simulation of three-dimensional （3D） non-isothermal, non-Newtonian fluid filling process is an extremely difficult task and remains a challenging problem, which includes polymer melt flow with free surface coupled with transient heat transfer. This paper presents a full 3D non-isothermal two-phase flow model to predict the complex flow in melt filling process, where the Cross-WLF model is applied to characterize the rheological behav- ior of polymer melt. The governing equations are solved using finite volume method with SIMPLEC algorithm on collocated grids and the melt front is accurately captured by a high resolution level set method. A domain exten- sion technique is adopted to deal with the complex cavities, which greatly reduces the computational burden. To verify the validity of the developed 3D approach, the melts filling processes in two thin rectangular cavities （one of them with a cylindrical insert） are simulated. The predicted melt front interfaces are in good agreement with the experiment and commercial software prediction. For a case with a rather complex cavity, the dynamic filling process in a hemispherical shell is successfully simulated. All of the numerical results show that the developed numerical procedure can provide a reasonable orediction for injection molding process.
文摘The oil oxidation characteristics of the whole temperature regions from 30 ℃ to 600 ℃ during oil reservoir air injection were revealed by experiments. The whole oil oxidation temperature regions were divided into four different parts: dissolving and inflation region, low temperature oxidation region, medium temperature oxidation region and high temperature oxidation region. The reaction mechanisms of different regions were explained. Based on the oil oxidation characteristics and filed tests results, light oil reservoirs air injection development methods were divided into two types: oxygen-reducing air flooding and air flooding;heavy oil reservoirs air injection in-situ combustion development methods were divided into two types: medium temperature in-situ combustion and high temperature in-situ combustion. When the reservoir temperature is lower than 120 ℃, oxygen-reducing air flooding should be used for light oil reservoir development. When the reservoir temperature is higher than 120 ℃, air flooding method should be used for light oil reservoir development. For a normal heavy oil reservoir, when the combustion front temperature is lower than 400 ℃, the development method is medium temperature in-situ combustion. For a heavy oil reservoir with high oil resin and asphalting contents, when the combustion front temperature is higher than 450 ℃, the development method at this condition is high temperature in-situ combustion. Ten years field tests of air injection carried out by PetroChina proved that air has advantages in technical, economical and gas source aspects compared with other gas agents for oilfield gas injection development. Air injection development can be used in low/super-low permeability light oil reservoirs, medium and high permeability light oil reservoirs and heavy oil reservoirs. Air is a very promising gas flooding agent.
基金Postdoctoral Foundation of China(No.20070410755)PAN Zhencun,born in 1962,male,postdoctor researcher.
文摘A diagnostic signal current trace detecting based single phase-to-ground fault line identifica- tion and section location method for non-effectively grounded distribution systems is presented in this paper.A special diagnostic signal current is injected into the fault distribution system,and then it is detected at the outlet terminals to identify the fault line and at the sectionalizing or branching point along the fault line to locate the fault section.The method has been put into application in actual distribution network and field experience shows that it can identify the fault line and locate the fault section correctly and effectively.
文摘As we all know, cyclic gas injection is one of the most effective development methods to improve condensate oil recovery. When dealing with the calculation of the reserves, the injection-production differences and water influx create great influence on the accuracy. Based on the existing research, we proposed a new material balance equation which considered the differences of composition between produced and injected fluids and the effect of water influx, and a solution was provided in this paper. The results of the method are closer to the actual situation because they are built on the law of conservation of mass, and the using of curve fitting method can not only avoid the use of water influx coefficient but also obtain the water influx rate and reserves at the same time. The YH-23 gas condensate reservoir is taking as a typical subject to do the research, which has been exploited by cycle gas injection for 14 years. Three different methods are used to calculate the reserves, and the results show that the method proposed in this paper has minimum error of 2.96%.
基金National Science and Technology Support Program of China ( No. 2009BAG15B02) Key Pro-grams for Science and Technology Development of Chinese Transportation Industry( No. 2008-353-332-160)
文摘The north anchorage caisson of Taizhou Bridge encountered some difficulties during the sinking process for the large sidewall frictional resistances. To solve this problem, a new concept and method called subsidence method aided by water injection is proposed. Numeral analysis is adopted to simulate the effects of this method for the north anchor of Taizhou Bridge, which confirmed the feasibility and validity. Finally, the method is applied to the north anchor caisson during the caisson sinking procedure and helps the caisson sink and embed to the designed position smoothly.
基金Project supported by Arm Pre-research Program （51333040101）, National Defense 973 Program （6131380301 ）, National Natural Science Foundation of China （61040003）.
文摘There are the application scope limits for single differential-mode current injection test method, so in order to carry out injection susceptibility test for two-pieces equipment interconnected with both ends of a cable simultaneously, a double differential-mode current in- jection test method (DDMCI) is proposed. The method adopted the equivalence source wave theorem and Baum-Liu-Tesche(BLT) equation as its theory foundation. The equivalent corresponding relation between injection voltage and radiation electric field intensity is derived, and the phase relation between the two injection voltage sources is confirmed. The results indicate that the amplitude and phase of the equivalent injection voltage source is closely related to the S parameter of directional coupling device, the transmission line length, and the source vector in BLT equation, but has nothing to do with the reflection coefficient between the two equipment pieces. Therefore, by choosing the right amplitude and phase of the double injection voltage sources, the DDMCI test is equivalent to the radiation test for two interconnected equipment of a system.
文摘OBJECTIVE: To compare the clinical effect of brachial plexus block with "One Injection Two Points" guided under ultrasound and the conventional method guiding by ultrasound. METHODS: 70 patients were randomized evenly into 2 groups, with 35 patients in each group, while the Experiment Group(Group B) received One Injection Two Points" method, the Control Group(Group A) received the conventional method.The nerve block every 5 s, the success rate of anesthesia, the dosage of local anesthetics, second remedial anesthesia, adverse reactions, etc.were recorded. RESULTS: Group B was superior to group A in the success rate of anesthesia; There were 6 patients in group A who required constant pump injection of Remifentanil to remedy, while no patients in Group B needed remedy treatment. There were no serious adverse reactions in both groups.CONCLUSIONS: The clinical effect of brachial plexus block with "One Injection Two Points" method guided under ultrasoundguiding by ultrasound was superior to that of the conventional method.
基金funded by the National Science and Technology Major Project of China,2016ZX05060-004,2017ZX05036-003the National Natural Science Foundation of China,51574218Strategic Priority Research Program of the Chinese Academy of Sciences,grant number XDB10040200。
文摘Compared with the middle-shallow shale gas reservoirs,deep shale formation often reveals lower fracture complexity,smaller effective stimulated volumes,lower conductivity,and faster declined when the same injection model and technical parameters were used.Therefore,it is necessary to research a special injection model for the deep shale formation.In this paper,a series of laboratory stimulated experiments were carried to analyze the injection method on hydraulic fracturing initiation and propagation in the deep shale formation.The outcrop shale of Longmaxi formation in Sichuan Basin was selected and three different injection methods(constant,stepped-rise and cyclic progressive uplift pump rate)were used in these experiments.The test results showed that the stepped-rise pump rate is conductive to opening the pre-existing natural fracture and bedding planes,the fracture complexity of this injection method is the highest.Meanwhile,the fracturing pressure and total injection volume are the lowest.In contrast,the cyclic-uplift injection method can only form a transverse fracture,and the fracturing pressure is the highest.The research results have an important theoretical guiding value for deep shale hydraulic fracturing operation.
基金supported by the General Program of National Natural Science Foundation of China“Theoretical and Experimental Study on Key Mechanical Problems in Unconventional Natural Gas Exploitation”(No.:11272216).
文摘Injection pressure is one of the key parameters used in the design of shale gas reservoir stimulation.Higher injection pressure helps to initiate fractures,inject fracturing fluid and proppant smoothly and maximize the stimulated reservoir volume as soon as possible.If the injection pressure is too high,however,the risk of casing deformation is increased significantly.In this paper,the numerical calculation format of the injection pressure safety window while ensuring casing integrity(i.e.,the maximum safety injection pressure)was proposed based on an example of an actual engineering project.Then,it was verified based on the actual situation of one shale gas well in Weiyuan.The numerical calculation format is as follows.First,a 3D finite element model of initial fine geostress field is established in the scale of block.Second,a primary submodel for introducing the asymmetric characteristics of reservoir stiffness to simulate the asymmetry of fracture distribution.Third,a secondary submodel containing the attributes of casing,cement sheath and reservoir material properties.Fourth,submodels are used to calculate the casing deformation generated by different injection loads and estimate the maximum allowable fracturing injection pressure(pj)while the safety requirement of casing deformation is satisfied.The calculation result of the case well shows that when the cementing quality is poor and fractures are distributed asymmetrically,the lateral and vertical displacements at the maximum displacement point of the casing under the injection pressure of 80 MPa are obviously lower than those under 90 MPa.According to the yield limit criterion of P-110 casing steel,the casing deformation in this case is elastic strain,so the injection pressure of 80 MPa is safe.In conclusion,this method has rational precision and accuracy,for its numerical result is consistent with the actual engineering phenomenon.
文摘Characteristics of heat transfer and flow of Newtonian and non-Newtonian fluids through porous walls and in porous media are studied due to their wide range of applications including geothermal reservoirs,heat exchangers,marine propulsion,and aerodynamics.The current study investigates the characteristics of heat transport in a reactive third-grade fluid,moving through permeable parallel plates,with uniform suction/injection velocity.The two permeable,parallel plates are maintained at the same,constant temperature.After being transformed into its dimensionless equivalent,governing equations are solved by employing the Least Squares Method(LSM).The LSM results are further validated with numerical solutions for temperature and velocity.The impact of cross-flow Reynolds number,Peclet number,heat generation parameter,non-Newtonian parameter,and Brinkman number on entropy generation,velocity,temperature,and Bejan number are investigated.Theresults indicate that temperature distribution is significantly influenced by the third-grade fluid parameter.The maximum temperature drops from almost 0.12 to 0.10 as the third-grade fluid parameter increases from0.05 to 0.4.When the cross-flow Reynolds number is raised from 0.05 to 3,the maximum temperature drops from 0.12 to around 0.09.Temperature is strongly influenced by the heat generation parameter.A greater understanding of the thermal characteristics necessary for the design of a variety of systems,such as heat exchangers,marine propulsion,aerodynamic systems,etc.,may be gained from the findings of the current study.
