This paper analyzes the necessity of the measurement of one-way delay, and it also points out the errors caused by the time offset between measurement devices. Then we propose an algorithm to estimate time offset betw...This paper analyzes the necessity of the measurement of one-way delay, and it also points out the errors caused by the time offset between measurement devices. Then we propose an algorithm to estimate time offset between measurement devices in network. With the estimated time offset, we can correct our measuring results. Simulation shows the effectiveness of our algorithm.展开更多
The linear transmission impairments,such as the timing offset(TO),frequency offset(FO),and chromatic dispersion(CD),are major factors of signal degradations in coherent optical fiber communication systems.The estimati...The linear transmission impairments,such as the timing offset(TO),frequency offset(FO),and chromatic dispersion(CD),are major factors of signal degradations in coherent optical fiber communication systems.The estimation and compensation of such impairments play significant roles in the receiver side digital signal processing(DSP)unit.In this paper,we propose to combat the linear impairments systematically(including TO,FO and CD)with a joint timefrequency signal processing by taking the advantage of fractional Fourier transform(FrFT).In view of geometrical analysis,TO/FO induces a shift in time/frequency coordinate and the CD leads to the rotation in the fractional domain.Both mathematical derivations and geometrical interpretations have been established to unveil the relationships between impairments and linear frequency modulated(LFM)training symbols(TSs).By considering a typical coherent optical orthogonal frequency-division multiplexing(COOFDM)transmission system,three kinds of linear impairments have been jointly estimated by simple geometric calculations using appropriately designed TS based on FrFTs.Simulation and experimental results confirmed the feasibility of time-frequency techniques with better accuracy,less complexity,and improved spectral efficiency.展开更多
For multiple-input multiple-output （MIMO） orthogonal frequency division multiplexing （OFDM） systems, a joint timing synchronization and frequency offset acquisition algorithm based on fractional Fourier transform ...For multiple-input multiple-output （MIMO） orthogonal frequency division multiplexing （OFDM） systems, a joint timing synchronization and frequency offset acquisition algorithm based on fractional Fourier transform （FRFT） is proposed. The linear frequency modulation signals superimposed on the data signals are used as the training signals. By performing FRFT on the received signals and searching the peak value of the FRFT results, the receiver can realize timing synchronization and frequency offset acquisition simultaneously. Compared with the existing methods, the proposed algorithm can provide better timing synchronization performance and larger frequency offset acquisition range even under multi-path channels with low signal to noise ratio. Theoretical analysis and simulation results prove this point.展开更多
In this paper, we consider the frequency offset estimation for Orthogonal Frequency-Division Multiple Access (OF-DMA) uplink (UL) transmissions. We first analyze the negative effect of Multi-Access-Interference (MAI) ...In this paper, we consider the frequency offset estimation for Orthogonal Frequency-Division Multiple Access (OF-DMA) uplink (UL) transmissions. We first analyze the negative effect of Multi-Access-Interference (MAI) on OFDMA UL, and then propose two interference reduction/elimination methods, i.e., the Reduced-Rank-Projector (RRP) and Shift-Sampling-Projector (SSP) methods, to eliminate/reduce the heavy MAI due to the frequency offsets. Finally, we propose a new training sequence group named the Round-Robin Training Sequence Group (RRTSG), which has a high interference mitigation capabilities for OFDMA UL transmission. The Cramer-Rao Lower Bound (CRLB) for an unbiased frequency offset estimator in a Multiple Access (MA) system is also derived. Numerical results show that the proposed methods are suitable to eliminate/mitigate the effect of the frequency offset on OFDMA UL transmission.展开更多
In this study, a series of tests have been conducted in order to investigate the machinability evaluation of austenitic Hadfield manganese steel in the Wire Electrical Discharge Machine (WEDM). Experimental investigat...In this study, a series of tests have been conducted in order to investigate the machinability evaluation of austenitic Hadfield manganese steel in the Wire Electrical Discharge Machine (WEDM). Experimental investigations have been carried out to relate the effect of input machining parameters such as pulse on-time (Ton), pulse off-time (Toff), wire feed (WF), and average gap voltage (V) on the wire offset in WEDM. No analytical approach gives the exact amount of offset required in WEDM and hence experimental study has been undertaken. In this paper, a mathematical model has been developed to model the machinability evaluation through the response surface methodology (RSM) capable of predicting the response parameter as a function of Ton, Toff, WF and V. The samples are tested and their average prediction error has been calculated taking the average of all the individual prediction errors. The result shows that this mathematical model reflects the independent, quadratic and interactive effects of the various machining parameters on cutting speed in WEDM process.展开更多
One of the important aspects in wireless sensor networks is time synchronization. Many applications such as military activity monitoring, environmental monitoring and forest fire monitoring require highly accurate tim...One of the important aspects in wireless sensor networks is time synchronization. Many applications such as military activity monitoring, environmental monitoring and forest fire monitoring require highly accurate time synchronization. Time synchronization assures that all the sensor nodes in wireless sensor network have the same clock time. It is not only essential for aforementioned applications but it is mandatory for TDMA scheduling and proper duty cycle coordination. Time synchronization is a challenging problem due to energy constraints. Most of the existing synchronization protocols use fixed nodes for synchronization, but in the proposed synchronization, algorithm mobile nodes are used to synchronize the stationary nodes in the sensing field. In this paper, we propose a new time synchronization algorithm, named controlled mobility time synchronization (CMTS) with the objective to achieve the higher accuracy while synchronizing the nodes. The proposed approach is used in this paper to synchronize the nodes externally by using the mobile nodes. Simulation results exhibit that proposed controlled mobility time synchronization increases the synchronization precision and reduces the energy consumption as well as synchronization error by reducing the collisions and retransmissions.展开更多
Time synchronization is one of the important aspects in wireless sensor networks. Time synchronization assures that all the sensor nodes in wireless sensor network have the same clock time. There are various applicati...Time synchronization is one of the important aspects in wireless sensor networks. Time synchronization assures that all the sensor nodes in wireless sensor network have the same clock time. There are various applications such as seismic study, military applications, pollution monitoring where sensor nodes require synchronized time. Time synchronization is mandatory for many wireless sensor networks protocols such as MAC protocols and also important for TDMA scheduling for proper duty cycle coordination. Time synchronization is a stimulating problem in wireless sensor networks because each node has its own local clock which keeps on varying due to variation in the oscillator frequency. The oscillator frequency is time varying due to ambient conditions which leads to re-synchronization of nodes time and again. This re-synchronization process is energy consuming whereas energy is constraints in WSN. This paper proposes a novel cluster based time synchronization technique for wireless sensor networks in which cluster head rotation is based on minimum clock offset. Simulation results based on energy analysis of the proposed model demonstrate that proposed novel cluster based time synchronization technique reduces the energy consumption and also the synchronization error compared with other existing protocols.展开更多
This paper proposes a distributed second-order consensus time synchronization, which incorporates the second-order consensus algorithm into wireless sensor networks. Since local clocks may have different skews and off...This paper proposes a distributed second-order consensus time synchronization, which incorporates the second-order consensus algorithm into wireless sensor networks. Since local clocks may have different skews and offsets, the algorithm is designed to include offset compensation and skew compensation. The local clocks are not directly modified, thus the virtual clocks are built according to the local clocks via the compensation parameters. Each node achieves a virtual consensus clock by periodically updated compensation parameters. Finally, the effectiveness of the proposed algorithm is verified through a number of simulations in a mesh network. It is proved that the proposed algorithm has the advantage of being distributed, asymptotic convergence, and robust to new node joining.展开更多
In this work we find a lower bound on the energy required for synchronizing moving sensor nodes in a Wireless Sensor Network (WSN) affected by large-scale fading, based on clock estimation techniques. The energy requi...In this work we find a lower bound on the energy required for synchronizing moving sensor nodes in a Wireless Sensor Network (WSN) affected by large-scale fading, based on clock estimation techniques. The energy required for synchronizing a WSN within a desired estimation error level is specified by both the transmit power and the required number of messages. In this paper we extend our previous work introducing nodes’ movement and the average message delay in the total energy, including a comprehensive analysis on how the distance between nodes impacts on the energy and synchronization quality trade-off under large-scale fading effects.展开更多
In this work, the existing trade-off between time synchronization quality and energy is studied for both large-scale and small-scale fading wireless channels. We analyze the clock offset estimation problem using one-w...In this work, the existing trade-off between time synchronization quality and energy is studied for both large-scale and small-scale fading wireless channels. We analyze the clock offset estimation problem using one-way, two-way and N-way message exchange mechanisms affected by Gaussian and exponentially distributed impairments. Our main contribution is a general relationship between the total energy required for synchronizing a wireless sensor network and the clock offset estimation error by means of the transmit power, number of transmitted messages and average message delay, deriving the energy optimal lower bound as a function of the time synchronization quality and the number of hops in a multi-hop network.展开更多
The Mw 9.0 Tohoku-Oki earthquake that hit the mainland Japan on 11 th March, 2011 had resulted a devastating Tsunami due to an active thrusting between the Pacific and the North American Plates. Static and kinematic o...The Mw 9.0 Tohoku-Oki earthquake that hit the mainland Japan on 11 th March, 2011 had resulted a devastating Tsunami due to an active thrusting between the Pacific and the North American Plates. Static and kinematic offsets at the offshore epicentre of the Mw 9.0 event remain unanswered and being investigated along with their near and far field limiting distances from the epicentre. Accordingly, offset measurements from 60 continuously operating IGS and GEONET GNSS stations were radially classified from the epicentre and interpreted with analytical models to find their linear offset decay rates. Co-and post-seismic static positional anomaly offsets of sixty days show almost all near field stations had strong or appreciable eastward or south eastward static shifts. Near stations(<250 km) showed both kinematic and static offsets. GEONET station ’0175’ showed maximum resultant static offset of-4.5 m, which diminishes approximately 1-2 cm at far sites like SMST and AIRA. Characteristic decay duration(’b’) of the mean kinematic co-seismic shift(’a’)of near field stations was 17.28 s during earthquake hours with an EW component shift >1.5 m. Spatial models of projected N-S static and kinematic offsets show their asymmetrical distributions around the epicentre with maximum model offset of-1.84 m displaced towards south at-45 km north of the epicentre. The Tohoku-Oki earthquake produced a resultant kinematic offset of-10.2 m towards East at its offshore epicentre;while the estimated near field static offset is ~9.82 m. However, both estimates are bigger than double the resultant offset measured value(~4.3 m) in the Japanese mainland using GPS. The difference in the kinematic and static near field offsets highlight that the near surface had elastic or in-elastic kinematic strain dissipation as against the lithospheric level viscoelastic static response, which resulted rapid kinematic strain release(1.12 cm/km)within the limiting radius of ~220 km from the Tohoku-Oki epicentre.展开更多
A spectrum efficient OFDM scheme named Time Domain Synchronous-OFDM(TDS-OFDM)is introduced into coherent optical transmission system,in which the pseudo noise(PN)sequence is exploited as guard interval to realize fram...A spectrum efficient OFDM scheme named Time Domain Synchronous-OFDM(TDS-OFDM)is introduced into coherent optical transmission system,in which the pseudo noise(PN)sequence is exploited as guard interval to realize frame synchronization,compensate the carrier frequency offset(CFO),and estimate and equalize channel simultaneously.Since there is no pilot signals or training symbols in TDS-OFDM,the proposed scheme can achieve higher spectral efficiency(SE)above 10%improvement comparing with CPOFDM.The proposed method is implemented and verified in a 28GBaud QPSK OFDM system and a 28GBaud 16QAM OFDM system.It is demonstrated that the proposed scheme shows high CFO estimation accuracy and synchronous accuracy.Under CFO and linewidth of laser source set as 100MHz and 100kHz respectively,BER of QPSK OFDM system is below 3.8e-3 at the optical signal-to-noise ratio(OSNR)of 13dB,and BER of 16QAM OFDM system is below 3.8e-3 at the OSNR of 20dB.展开更多
文摘This paper analyzes the necessity of the measurement of one-way delay, and it also points out the errors caused by the time offset between measurement devices. Then we propose an algorithm to estimate time offset between measurement devices in network. With the estimated time offset, we can correct our measuring results. Simulation shows the effectiveness of our algorithm.
文摘The linear transmission impairments,such as the timing offset(TO),frequency offset(FO),and chromatic dispersion(CD),are major factors of signal degradations in coherent optical fiber communication systems.The estimation and compensation of such impairments play significant roles in the receiver side digital signal processing(DSP)unit.In this paper,we propose to combat the linear impairments systematically(including TO,FO and CD)with a joint timefrequency signal processing by taking the advantage of fractional Fourier transform(FrFT).In view of geometrical analysis,TO/FO induces a shift in time/frequency coordinate and the CD leads to the rotation in the fractional domain.Both mathematical derivations and geometrical interpretations have been established to unveil the relationships between impairments and linear frequency modulated(LFM)training symbols(TSs).By considering a typical coherent optical orthogonal frequency-division multiplexing(COOFDM)transmission system,three kinds of linear impairments have been jointly estimated by simple geometric calculations using appropriately designed TS based on FrFTs.Simulation and experimental results confirmed the feasibility of time-frequency techniques with better accuracy,less complexity,and improved spectral efficiency.
基金supported by the National Natural Science Foundation of China(60672047).
文摘For multiple-input multiple-output （MIMO） orthogonal frequency division multiplexing （OFDM） systems, a joint timing synchronization and frequency offset acquisition algorithm based on fractional Fourier transform （FRFT） is proposed. The linear frequency modulation signals superimposed on the data signals are used as the training signals. By performing FRFT on the received signals and searching the peak value of the FRFT results, the receiver can realize timing synchronization and frequency offset acquisition simultaneously. Compared with the existing methods, the proposed algorithm can provide better timing synchronization performance and larger frequency offset acquisition range even under multi-path channels with low signal to noise ratio. Theoretical analysis and simulation results prove this point.
文摘In this paper, we consider the frequency offset estimation for Orthogonal Frequency-Division Multiple Access (OF-DMA) uplink (UL) transmissions. We first analyze the negative effect of Multi-Access-Interference (MAI) on OFDMA UL, and then propose two interference reduction/elimination methods, i.e., the Reduced-Rank-Projector (RRP) and Shift-Sampling-Projector (SSP) methods, to eliminate/reduce the heavy MAI due to the frequency offsets. Finally, we propose a new training sequence group named the Round-Robin Training Sequence Group (RRTSG), which has a high interference mitigation capabilities for OFDMA UL transmission. The Cramer-Rao Lower Bound (CRLB) for an unbiased frequency offset estimator in a Multiple Access (MA) system is also derived. Numerical results show that the proposed methods are suitable to eliminate/mitigate the effect of the frequency offset on OFDMA UL transmission.
文摘In this study, a series of tests have been conducted in order to investigate the machinability evaluation of austenitic Hadfield manganese steel in the Wire Electrical Discharge Machine (WEDM). Experimental investigations have been carried out to relate the effect of input machining parameters such as pulse on-time (Ton), pulse off-time (Toff), wire feed (WF), and average gap voltage (V) on the wire offset in WEDM. No analytical approach gives the exact amount of offset required in WEDM and hence experimental study has been undertaken. In this paper, a mathematical model has been developed to model the machinability evaluation through the response surface methodology (RSM) capable of predicting the response parameter as a function of Ton, Toff, WF and V. The samples are tested and their average prediction error has been calculated taking the average of all the individual prediction errors. The result shows that this mathematical model reflects the independent, quadratic and interactive effects of the various machining parameters on cutting speed in WEDM process.
文摘One of the important aspects in wireless sensor networks is time synchronization. Many applications such as military activity monitoring, environmental monitoring and forest fire monitoring require highly accurate time synchronization. Time synchronization assures that all the sensor nodes in wireless sensor network have the same clock time. It is not only essential for aforementioned applications but it is mandatory for TDMA scheduling and proper duty cycle coordination. Time synchronization is a challenging problem due to energy constraints. Most of the existing synchronization protocols use fixed nodes for synchronization, but in the proposed synchronization, algorithm mobile nodes are used to synchronize the stationary nodes in the sensing field. In this paper, we propose a new time synchronization algorithm, named controlled mobility time synchronization (CMTS) with the objective to achieve the higher accuracy while synchronizing the nodes. The proposed approach is used in this paper to synchronize the nodes externally by using the mobile nodes. Simulation results exhibit that proposed controlled mobility time synchronization increases the synchronization precision and reduces the energy consumption as well as synchronization error by reducing the collisions and retransmissions.
文摘Time synchronization is one of the important aspects in wireless sensor networks. Time synchronization assures that all the sensor nodes in wireless sensor network have the same clock time. There are various applications such as seismic study, military applications, pollution monitoring where sensor nodes require synchronized time. Time synchronization is mandatory for many wireless sensor networks protocols such as MAC protocols and also important for TDMA scheduling for proper duty cycle coordination. Time synchronization is a stimulating problem in wireless sensor networks because each node has its own local clock which keeps on varying due to variation in the oscillator frequency. The oscillator frequency is time varying due to ambient conditions which leads to re-synchronization of nodes time and again. This re-synchronization process is energy consuming whereas energy is constraints in WSN. This paper proposes a novel cluster based time synchronization technique for wireless sensor networks in which cluster head rotation is based on minimum clock offset. Simulation results based on energy analysis of the proposed model demonstrate that proposed novel cluster based time synchronization technique reduces the energy consumption and also the synchronization error compared with other existing protocols.
基金Supported by the National Natural Science Foundation of China(No.61340034)the Research Program of Application Foundation and Advanced Technology of Tianjin(No.13JCYBJC15600)
文摘This paper proposes a distributed second-order consensus time synchronization, which incorporates the second-order consensus algorithm into wireless sensor networks. Since local clocks may have different skews and offsets, the algorithm is designed to include offset compensation and skew compensation. The local clocks are not directly modified, thus the virtual clocks are built according to the local clocks via the compensation parameters. Each node achieves a virtual consensus clock by periodically updated compensation parameters. Finally, the effectiveness of the proposed algorithm is verified through a number of simulations in a mesh network. It is proved that the proposed algorithm has the advantage of being distributed, asymptotic convergence, and robust to new node joining.
文摘In this work we find a lower bound on the energy required for synchronizing moving sensor nodes in a Wireless Sensor Network (WSN) affected by large-scale fading, based on clock estimation techniques. The energy required for synchronizing a WSN within a desired estimation error level is specified by both the transmit power and the required number of messages. In this paper we extend our previous work introducing nodes’ movement and the average message delay in the total energy, including a comprehensive analysis on how the distance between nodes impacts on the energy and synchronization quality trade-off under large-scale fading effects.
文摘In this work, the existing trade-off between time synchronization quality and energy is studied for both large-scale and small-scale fading wireless channels. We analyze the clock offset estimation problem using one-way, two-way and N-way message exchange mechanisms affected by Gaussian and exponentially distributed impairments. Our main contribution is a general relationship between the total energy required for synchronizing a wireless sensor network and the clock offset estimation error by means of the transmit power, number of transmitted messages and average message delay, deriving the energy optimal lower bound as a function of the time synchronization quality and the number of hops in a multi-hop network.
文摘The Mw 9.0 Tohoku-Oki earthquake that hit the mainland Japan on 11 th March, 2011 had resulted a devastating Tsunami due to an active thrusting between the Pacific and the North American Plates. Static and kinematic offsets at the offshore epicentre of the Mw 9.0 event remain unanswered and being investigated along with their near and far field limiting distances from the epicentre. Accordingly, offset measurements from 60 continuously operating IGS and GEONET GNSS stations were radially classified from the epicentre and interpreted with analytical models to find their linear offset decay rates. Co-and post-seismic static positional anomaly offsets of sixty days show almost all near field stations had strong or appreciable eastward or south eastward static shifts. Near stations(<250 km) showed both kinematic and static offsets. GEONET station ’0175’ showed maximum resultant static offset of-4.5 m, which diminishes approximately 1-2 cm at far sites like SMST and AIRA. Characteristic decay duration(’b’) of the mean kinematic co-seismic shift(’a’)of near field stations was 17.28 s during earthquake hours with an EW component shift >1.5 m. Spatial models of projected N-S static and kinematic offsets show their asymmetrical distributions around the epicentre with maximum model offset of-1.84 m displaced towards south at-45 km north of the epicentre. The Tohoku-Oki earthquake produced a resultant kinematic offset of-10.2 m towards East at its offshore epicentre;while the estimated near field static offset is ~9.82 m. However, both estimates are bigger than double the resultant offset measured value(~4.3 m) in the Japanese mainland using GPS. The difference in the kinematic and static near field offsets highlight that the near surface had elastic or in-elastic kinematic strain dissipation as against the lithospheric level viscoelastic static response, which resulted rapid kinematic strain release(1.12 cm/km)within the limiting radius of ~220 km from the Tohoku-Oki epicentre.
基金supported by the State Grid Corporation of China (No. 5101/2017-3205A)the Open Fund of the Guangdong Provincial Key Laboratory of Optical Fiber Sensing and Communications (Jinan University)the National Natural Science Foundation of China (NSFC) (61571057, 61501214, 61527820, 61575082)
文摘A spectrum efficient OFDM scheme named Time Domain Synchronous-OFDM(TDS-OFDM)is introduced into coherent optical transmission system,in which the pseudo noise(PN)sequence is exploited as guard interval to realize frame synchronization,compensate the carrier frequency offset(CFO),and estimate and equalize channel simultaneously.Since there is no pilot signals or training symbols in TDS-OFDM,the proposed scheme can achieve higher spectral efficiency(SE)above 10%improvement comparing with CPOFDM.The proposed method is implemented and verified in a 28GBaud QPSK OFDM system and a 28GBaud 16QAM OFDM system.It is demonstrated that the proposed scheme shows high CFO estimation accuracy and synchronous accuracy.Under CFO and linewidth of laser source set as 100MHz and 100kHz respectively,BER of QPSK OFDM system is below 3.8e-3 at the optical signal-to-noise ratio(OSNR)of 13dB,and BER of 16QAM OFDM system is below 3.8e-3 at the OSNR of 20dB.
