Hydrogen fuel cell ships are one of the key solutions to achieving zero carbon emissions in shipping.Multi-fuel cell stacks(MFCS)systems are frequently employed to fulfill the power requirements of high-load power equ...Hydrogen fuel cell ships are one of the key solutions to achieving zero carbon emissions in shipping.Multi-fuel cell stacks(MFCS)systems are frequently employed to fulfill the power requirements of high-load power equipment on ships.Compared to single-stack system,MFCS may be difficult to apply traditional energy management strategies(EMS)due to their complex structure.In this paper,a two-layer power allocation strategy for MFCS of a hydrogen fuel cell ship is proposed to reduce the complexity of the allocation task by splitting it into each layer of the EMS.The first layer of the EMSis centered on the Nonlinear Model Predictive Control(NMPC).The Northern Goshawk Optimization(NGO)algorithm is used to solve the nonlinear optimization problem in NMPC,and the local fine search is performed using sequential quadratic programming(SQP).Based on the power allocation results of the first layer,the second layer is centered on a fuzzy rule-based adaptive power allocation strategy(AP-Fuzzy).The membership function bounds of the fuzzy controller are related to the aging level of the MFCS.The Particle Swarm Optimization(PSO)algorithm is used to optimize the parameters of the residual membership function to improve the performance of the proposed strategy.The effectiveness of the proposed EMS is verified by comparing it with the traditional EMS.The experimental results show that the EMS proposed in this paper can ensure reasonable hydrogen consumption,slow down the FC aging and equalize its performance,effectively extend the system life,and ensure that the ship has good endurance after completing the mission.展开更多
Mg-12 Li, Mg-12 Li-3（Al-Si）, Mg-12 Li-7（Al-Si） and Mg-12 Li-9（Al-Si） alloys（all in wt%） were fabricated by high frequency vacuum induction melting in a water cooled copper crucible. After subsequently hotrolli...Mg-12 Li, Mg-12 Li-3（Al-Si）, Mg-12 Li-7（Al-Si） and Mg-12 Li-9（Al-Si） alloys（all in wt%） were fabricated by high frequency vacuum induction melting in a water cooled copper crucible. After subsequently hotrolling and annealing, their microstructure and mechanical properties were investigated. Experimental results show that mechanical properties of Mg-12 Li alloy were significantly improved by the addition of Al-Si eutectic alloy. Mg-12 Li-7（Al-Si） alloy shows the highest strength of 196 MPa of the investigated alloys, which is about 1.8 times of the strength of Mg-12 Li alloy, and maintains high elongation of 27%.The improved mechanical property with addition of Al and Si in the eutectic proportion into Mg-12 Li alloy was attributed to the solution strengthening effect of A1 and precipitation hardening effect from AlLi and Mg_2 Si precipitates.展开更多
To improve the homogeneity and rolling formability of as-cast AZ91 magnesium,the effects of pre-homogenizing treatment on microstructure evolution,deformation mechanism,mechanical properties and tensile fracture morph...To improve the homogeneity and rolling formability of as-cast AZ91 magnesium,the effects of pre-homogenizing treatment on microstructure evolution,deformation mechanism,mechanical properties and tensile fracture morphology of hot-rolled AZ91 magnesium alloy were studied.The results showed that the amount of coarseβ-Mg17Al12 phase decreases dramatically,being distributed along the grain boundaries as small strips after homogenizing.Twining plays a dominant role in the deformation mechanism of AZ91 alloys in the experimental condition,while dynamic recrystallization(DRX)considerably occurred in homogenized-rolled alloys,contributed to microstructure uniformity andβ-Mg17Al12 phase precipitated refinement.The tensile strength of homogenized-rolled AZ91 alloys increases dramatically with elongation declining slightly in contrast to homogenized alloys.The fracture surface of homogenized-rolled specimen exhibits more ductile fracture with the manifestation of a large amount of dimples distributing higher density in matrix,while the micro cracks are prone to initiate around the Mg/Mg17Al12 phase interface and grain boundaries owing to the fragile interface bonding of two phases.展开更多
In order to increase the depth or concentration of Ti ion implantation of pure iron, the surface mechanical attrition treatment(SMAT), which can fabricate a nanometer-grained surface layer without porosity and contami...In order to increase the depth or concentration of Ti ion implantation of pure iron, the surface mechanical attrition treatment(SMAT), which can fabricate a nanometer-grained surface layer without porosity and contamination in a pure iron plate, was used before ion implantation. Ti ion was implanted into the SMA treated sample and coarse-grained counterpart by using a metal vapor vacuum arc source implanter. The changing of depth and concentration of Ti was studied in a function of implantation time.By optical microscopy, transmission electron microscopy and X-ray diffraction, the grain size of the nano structured surface was studied. Micro-hardness, friction and wear behavior of nano surface layers were studied. By energy dispersive X-ray spectroscopy and Auger electron spectroscopy, the chemical composition and concentration of Ti ion in the surface implantation layer were studied. Experimental results showed that the concentration of Ti increased dramatically compared with untreated coarsegrained samples, which is attributed to the existence of higher density of defects(supersaturated vacancies, dislocations, non-equilibrium grain boundaries etc.) and compression stress field in the SMA treated nanocrystallined surface layer. The interaction between the defects and the implanted solute atoms leads to the increment of solid solubility. But the implantation depth showed inconspicuous change. It is shown that the ion range is just relevant to the energy and mass of the ion, dose of injection,the mass and density of target material.展开更多
基金supported by the National Key R&D Program of China(2022YFB4301403).
文摘Hydrogen fuel cell ships are one of the key solutions to achieving zero carbon emissions in shipping.Multi-fuel cell stacks(MFCS)systems are frequently employed to fulfill the power requirements of high-load power equipment on ships.Compared to single-stack system,MFCS may be difficult to apply traditional energy management strategies(EMS)due to their complex structure.In this paper,a two-layer power allocation strategy for MFCS of a hydrogen fuel cell ship is proposed to reduce the complexity of the allocation task by splitting it into each layer of the EMS.The first layer of the EMSis centered on the Nonlinear Model Predictive Control(NMPC).The Northern Goshawk Optimization(NGO)algorithm is used to solve the nonlinear optimization problem in NMPC,and the local fine search is performed using sequential quadratic programming(SQP).Based on the power allocation results of the first layer,the second layer is centered on a fuzzy rule-based adaptive power allocation strategy(AP-Fuzzy).The membership function bounds of the fuzzy controller are related to the aging level of the MFCS.The Particle Swarm Optimization(PSO)algorithm is used to optimize the parameters of the residual membership function to improve the performance of the proposed strategy.The effectiveness of the proposed EMS is verified by comparing it with the traditional EMS.The experimental results show that the EMS proposed in this paper can ensure reasonable hydrogen consumption,slow down the FC aging and equalize its performance,effectively extend the system life,and ensure that the ship has good endurance after completing the mission.
基金supported by the Shanxi Scholarship Council of China (No.2014-029)the National Natural Science Foundation of China (Nos. 51474152, 51401143 and 51274149)
文摘Mg-12 Li, Mg-12 Li-3（Al-Si）, Mg-12 Li-7（Al-Si） and Mg-12 Li-9（Al-Si） alloys（all in wt%） were fabricated by high frequency vacuum induction melting in a water cooled copper crucible. After subsequently hotrolling and annealing, their microstructure and mechanical properties were investigated. Experimental results show that mechanical properties of Mg-12 Li alloy were significantly improved by the addition of Al-Si eutectic alloy. Mg-12 Li-7（Al-Si） alloy shows the highest strength of 196 MPa of the investigated alloys, which is about 1.8 times of the strength of Mg-12 Li alloy, and maintains high elongation of 27%.The improved mechanical property with addition of Al and Si in the eutectic proportion into Mg-12 Li alloy was attributed to the solution strengthening effect of A1 and precipitation hardening effect from AlLi and Mg_2 Si precipitates.
基金the National Natural Science Foundation of China(Grant Nos.51175363 and 51474152)the Research Project Supported by the Shanxi Scholarship Council of China(Grant Nos.2014029)。
文摘To improve the homogeneity and rolling formability of as-cast AZ91 magnesium,the effects of pre-homogenizing treatment on microstructure evolution,deformation mechanism,mechanical properties and tensile fracture morphology of hot-rolled AZ91 magnesium alloy were studied.The results showed that the amount of coarseβ-Mg17Al12 phase decreases dramatically,being distributed along the grain boundaries as small strips after homogenizing.Twining plays a dominant role in the deformation mechanism of AZ91 alloys in the experimental condition,while dynamic recrystallization(DRX)considerably occurred in homogenized-rolled alloys,contributed to microstructure uniformity andβ-Mg17Al12 phase precipitated refinement.The tensile strength of homogenized-rolled AZ91 alloys increases dramatically with elongation declining slightly in contrast to homogenized alloys.The fracture surface of homogenized-rolled specimen exhibits more ductile fracture with the manifestation of a large amount of dimples distributing higher density in matrix,while the micro cracks are prone to initiate around the Mg/Mg17Al12 phase interface and grain boundaries owing to the fragile interface bonding of two phases.
基金the National Natural Science Foundation of China (Grant Nos. 21201129, 51374151), P. R. Chinathe Major Project for Science & Technology of Shanxi Province (20111101053)+2 种基金the Key Project for Science & Technology of coal base research in Shanxi Provincethe National Natural Science Foundation of Shanxi Province (Nos. 2011011020-2 and 2010021023-1)the Young Foundation of Shanxi Medical University (No. 057546)
文摘In order to increase the depth or concentration of Ti ion implantation of pure iron, the surface mechanical attrition treatment(SMAT), which can fabricate a nanometer-grained surface layer without porosity and contamination in a pure iron plate, was used before ion implantation. Ti ion was implanted into the SMA treated sample and coarse-grained counterpart by using a metal vapor vacuum arc source implanter. The changing of depth and concentration of Ti was studied in a function of implantation time.By optical microscopy, transmission electron microscopy and X-ray diffraction, the grain size of the nano structured surface was studied. Micro-hardness, friction and wear behavior of nano surface layers were studied. By energy dispersive X-ray spectroscopy and Auger electron spectroscopy, the chemical composition and concentration of Ti ion in the surface implantation layer were studied. Experimental results showed that the concentration of Ti increased dramatically compared with untreated coarsegrained samples, which is attributed to the existence of higher density of defects(supersaturated vacancies, dislocations, non-equilibrium grain boundaries etc.) and compression stress field in the SMA treated nanocrystallined surface layer. The interaction between the defects and the implanted solute atoms leads to the increment of solid solubility. But the implantation depth showed inconspicuous change. It is shown that the ion range is just relevant to the energy and mass of the ion, dose of injection,the mass and density of target material.
