The Split Hopkinson Pressure Bar(SHPB) technique with a special experimental apparatus can be used to obtain the material behaviors under high strain rate loading condition. Attempts to apply the Split Hopkison Pressu...The Split Hopkinson Pressure Bar(SHPB) technique with a special experimental apparatus can be used to obtain the material behaviors under high strain rate loading condition. Attempts to apply the Split Hopkison Pressure Bar in measurement on polymeric materials suffer from limitations on the maximum achievable strain and from high noise to signal ratios. This paper introduces a Split Hopkinson Pressure Bar technique, to overcome these limitations. The proposed method uses aluminum pressure bars to achieve a closer impedance match between the pressure bars and the specimen materials, thus providing both data having a low noise to signal ratio and a longer input pulse at higher maximum strain. In addition, a pulse shaper technique was used for increasing the rise time of the incident pulse to ensure stress equilibrium and homogeneous deformation in the specimen under dynamic compression. A pulse shaper is utilized to lengthen the rising time of the incident pulse to ensure stress equilibrium and homogeneous deformation of polycarbonate. The dynamic deformation behaviors of Polymeric material under compressive high strain rate are evaluated using the modified SHPB technique.展开更多
The crystallization process of the eutectic composition of GdAlO_3-Al_2O_3 from the amorphous phase prepared by rapid-quenching of melt that leads to the formation of a cantaloupe skin-like microstructure was investig...The crystallization process of the eutectic composition of GdAlO_3-Al_2O_3 from the amorphous phase prepared by rapid-quenching of melt that leads to the formation of a cantaloupe skin-like microstructure was investigated using focused ion-beam scanning electron microscopy (FIB-SEM) and high-resolution transmission electron microscopy (HR-TEM).The amorphous films were heat-treated at temperatures between 1000 °C and 1500 °C for up to 30min to form the eutectic phases of GdAlO_3 and Al_2O_3.The GdAlO_3 and Al_2O_3 crystal phases that formed from the amorphous phase were identified by FIB-SEM and HR-TEM.Both components began to crystallize and grow from the amorphous phase separately at different temperatures.The formation process of these crystal phases was different from that of the ordinary eutectic microstructure solidified from the GdAlO_3-Al_2O_3 system.Therefore,the observed structure is termed "eutectic-like" for distinction.The microstructures formed from the amorphous phases at sufficiently high temperatures consisted of ultra-fine microstructures of individually crystallized components and were similar to ordinary eutectic microstructures.By heat-treating the amorphous films at 1500 °C for either 2 min,8min or 30min,the ultra-fine components of GdAlO_3 and Al_2O_3 were found to crystallize following a eutectic-like stage after 8min of heat treatment.展开更多
文摘The Split Hopkinson Pressure Bar(SHPB) technique with a special experimental apparatus can be used to obtain the material behaviors under high strain rate loading condition. Attempts to apply the Split Hopkison Pressure Bar in measurement on polymeric materials suffer from limitations on the maximum achievable strain and from high noise to signal ratios. This paper introduces a Split Hopkinson Pressure Bar technique, to overcome these limitations. The proposed method uses aluminum pressure bars to achieve a closer impedance match between the pressure bars and the specimen materials, thus providing both data having a low noise to signal ratio and a longer input pulse at higher maximum strain. In addition, a pulse shaper technique was used for increasing the rise time of the incident pulse to ensure stress equilibrium and homogeneous deformation in the specimen under dynamic compression. A pulse shaper is utilized to lengthen the rising time of the incident pulse to ensure stress equilibrium and homogeneous deformation of polycarbonate. The dynamic deformation behaviors of Polymeric material under compressive high strain rate are evaluated using the modified SHPB technique.
基金part of the study under the "Human Resource Development Center for Economic Region Leading Industry" Projectsupported by the Ministry of Education,Science & Technology(MEST)by the National Research Foundation of Korea(NRF)
文摘The crystallization process of the eutectic composition of GdAlO_3-Al_2O_3 from the amorphous phase prepared by rapid-quenching of melt that leads to the formation of a cantaloupe skin-like microstructure was investigated using focused ion-beam scanning electron microscopy (FIB-SEM) and high-resolution transmission electron microscopy (HR-TEM).The amorphous films were heat-treated at temperatures between 1000 °C and 1500 °C for up to 30min to form the eutectic phases of GdAlO_3 and Al_2O_3.The GdAlO_3 and Al_2O_3 crystal phases that formed from the amorphous phase were identified by FIB-SEM and HR-TEM.Both components began to crystallize and grow from the amorphous phase separately at different temperatures.The formation process of these crystal phases was different from that of the ordinary eutectic microstructure solidified from the GdAlO_3-Al_2O_3 system.Therefore,the observed structure is termed "eutectic-like" for distinction.The microstructures formed from the amorphous phases at sufficiently high temperatures consisted of ultra-fine microstructures of individually crystallized components and were similar to ordinary eutectic microstructures.By heat-treating the amorphous films at 1500 °C for either 2 min,8min or 30min,the ultra-fine components of GdAlO_3 and Al_2O_3 were found to crystallize following a eutectic-like stage after 8min of heat treatment.
