The effect of Portland cement （OPC） addition on the properties of high calcium fly ash geopolymer pastes was investigated in the paper. OPC partially replaced fly ash （FA） at the dosages of 0, 5%, 10%, and 15% by ...The effect of Portland cement （OPC） addition on the properties of high calcium fly ash geopolymer pastes was investigated in the paper. OPC partially replaced fly ash （FA） at the dosages of 0, 5%, 10%, and 15% by mass of binder. Sodium silicate （Na2SiO3） and sodium hydroxide （NaOH） solutions were used as the liquid portion in the mixture： NaOH 10 mol/L, Na2SiO3/NaOH with a mass ratio of 2.0, and alkaline liquid/binder （L/B） with a mass ratio of 0.6. The curing at 60℃ for 24 h was used to accelerate the geopolymerization. The setting time of all fresh pastes, porosity, and compressive strength of the pastes at the stages of 1, 7, 28, and 90 d were tested. The elastic modulus and strain capacity of the pastes at the stage of 7 d were determined. It is revealed that the use of OPC as an additive to replace part of FA results-in the decreases in the setting time, porosity, and strain capacity of the paste specimens, while the compressive strength and elastic modulus seem to increase.展开更多
Owing to the high viscosity of sodium silicate solution, fly ash geopolymer has the problems of low workability and rapid setting time. Therefore, the effect of chemical admixtures on the properties of fly ash geopoly...Owing to the high viscosity of sodium silicate solution, fly ash geopolymer has the problems of low workability and rapid setting time. Therefore, the effect of chemical admixtures on the properties of fly ash geopolymer was studied to overcome the rapid set of the geo-polymer in this paper. High-calcium fly ash and alkaline solution were used as starting materials to synthesize the geopolymer. Calcium chloride, calcium sulfate, sodium sulfate, and sucrose at dosages of 1wt% and 2wt% of fly ash were selected as admixtures based on concrete knowledge to improve the properties of the geopolymer. The setting time, compressive strength, and degree of reaction were recorded, and the microstructure was examined. The results show that calcium chloride significantly shortens both the initial and final setting times of the geopolymer paste. In addition, sucrose also delays the final setting time significantly. The degrees of reaction of fly ash in the geopolymer paste with the admixtures are all higher than those of the control paste. This contributes to the obvious increases in compressive strength.展开更多
The effect of grinding on the chemical and physical properties of rice husk ash was studied. Four rice husk ashes with different finenesses, i.e. coarse original rice husk ash （RHA0）, RHA1, RHA2, and RHA3 were used ...The effect of grinding on the chemical and physical properties of rice husk ash was studied. Four rice husk ashes with different finenesses, i.e. coarse original rice husk ash （RHA0）, RHA1, RHA2, and RHA3 were used for the study. Ordinary Portland cement （OPC） was partially replaced with rice husk ash at 20% by weight of binder. The water to binder ratio （W/B） of the mortar was maintained at 110%±5% with flow table test. Specific gravity, fineness, chemical properties, compressive strength, and porosity test of mortars were determined. The differences in chemical composition of the rice husk ashes with different finenesses from the same batch are small. The use of RHA3 produces the mortars with good strength and low porosity. The strength of the mortar improves with partial replacement of RHA3 in comparison with normal coarse rice husk ash. The use of RHA3 results in a strong and dense mortar, which is due to the better dispersion and filling effect, as well as an increase in the pozzolanic reaction.展开更多
The effects of the fineness and shape of fly ash on the porosity and air permeability of cement pastes were investigated. Pulverized coal combustion （PCC） fly ash and fluidized bed coal combustion （FBC） fly ash cl...The effects of the fineness and shape of fly ash on the porosity and air permeability of cement pastes were investigated. Pulverized coal combustion （PCC） fly ash and fluidized bed coal combustion （FBC） fly ash classified into three different finenesses were used. River sand with particle size distribution similar to that of fly ash was also used for comparison. Portland cement was replaced with fly ash and ground sand at the dosages of 0, 20wt%, and 40wt%. A water-to-binder ratio （w/b） of 0.35 was used throughout the experiment. The results show that the porosity and air permeability of the pastes are influenced by the shape, fineness, and replacement level of fly ash. The porosity and air permeability of FBC fly ash pastes are higher than those of PCC fly ash pastes. This is due to the higher irregular shape and surface of FBC fly ash compared to the spherical shape and relatively smooth surface of PCC fly ash. The porosity increases with the increase in fly ash replacement level and decreases with the increase in its fineness. The permeability of PCC fly ash pastes decreases with the increase in replacement level and fineness, while for FBC fly ash, the permeability increases with the increase in replacement level. Decreases in porosity and permeability are due to a combined effect of the packing of fine particles and the reaction of fly ash.展开更多
The shrinkage of fly ash geopolymers was studied in the present study.Fly ash was used as the source material for making the geopolymers.The effects of the concentration of NaOH,sodium silicate-to-NaOH ratio,liquid-to...The shrinkage of fly ash geopolymers was studied in the present study.Fly ash was used as the source material for making the geopolymers.The effects of the concentration of NaOH,sodium silicate-to-NaOH ratio,liquid-to-ash ratio,curing temperature,and curing time on shrinkage were investigated.The geopolymers were cured at 25,40,and 60℃,respectively.The results indicate that the shrinkage of geopolymers is strongly dependent on curing temperature and liquid-to-ash ratio.The increase in shrinkage is associated with the low strength development of geopolymers.It is also found that NaOH concentration and sodium silicate-to-NaOH ratio also affect the shrinkage of geopolymers but to a lesser extent.展开更多
This paper presented a study on the strength and chloride resistance of mortars made with ternary blends of ordinary Portland cement （OPC）, ground palm oil fuel ash （POA）, and classified fly ash （FA）. The mortar...This paper presented a study on the strength and chloride resistance of mortars made with ternary blends of ordinary Portland cement （OPC）, ground palm oil fuel ash （POA）, and classified fly ash （FA）. The mortar mixtures were made with Portland cement type I containing 0-40wt% FA and POA. FA and POA with 1wt%-3wt% retained on a sieve No.325 were used. The compressive strength and rapid chloride penetration depth of mortars were determined. The results reveal that the use of ternary blended cements produces good strength mortars. The use of the blend of FA and POA also produces high strength mortars and excellent resistance to chloride penetration owing to the synergic effect of FA and POA. A mathematical analysis and two-parameter polynomial model were presented to predict the compressive strength. The mathematical model correlated well with the experimental results. The computer 3-D graphics of strength of the ternary blended mortars were also constructed and could be used to aid the understanding and the proportioning of the blended system.展开更多
Cellular lightweight concrete （CLC） with the controlled density of approximately 800 kg/m3 was made from a preformed foam, Type-I Portland cement （OPC）, fly ash （FA）, or natural zeolite （NZ）, and its compressi...Cellular lightweight concrete （CLC） with the controlled density of approximately 800 kg/m3 was made from a preformed foam, Type-I Portland cement （OPC）, fly ash （FA）, or natural zeolite （NZ）, and its compressive strength, setting time, water absorption, and microstructure of were tested. High-calcium FA and NZ with the median particle sizes of 14.52 and 7.72 μm, respectively, were used to partially replace OPC at 0, 10wt%, 20wt%, and 30wt% of the binder （OPC and pozzolan admixture）. A water-to-binder mass ratio （W/B） of 0.5 was used for all mixes. The testing results indicated that CLC containing 10wt% NZ had the highest compressive strength. The replacement of OPC with NZ decreased the total porosity and air void size but increased the capillary porosity of the CLC. The incorporation of a suitable amount of NZ decreased the setting time, total porosity, and pore size of the paste compared with the findings with the same amount of FA. The total porosity and cumulative pore volume decreased, whereas the gel and capillary pores increased as a result of adding both pozzolans at all replacement levels. The water absorption increased as the capillary porosity increased; this effect depended on the volume of air entrained and the type or amount of pozzolan.展开更多
The construction industry is facing a big challenge in reducing the burden it is putting on the environment. There is an urgent need to develop and use eco-efficient construction materials with proper functional perfo...The construction industry is facing a big challenge in reducing the burden it is putting on the environment. There is an urgent need to develop and use eco-efficient construction materials with proper functional performance, a low carbon footprint and a less adverse impact on the environment. Nanotechnology is a new and very promising technology that helps fulfil the need for more environmentally friendly construction materials.展开更多
The development of high volume rice husk ash （RHA） alumino silicate composites （ASC） was studied. RHA was used as the source of silica and aluminium in the ASC. The mass ratios of RHA：Al（OH）3 of 70：30 to 99：1...The development of high volume rice husk ash （RHA） alumino silicate composites （ASC） was studied. RHA was used as the source of silica and aluminium in the ASC. The mass ratios of RHA：Al（OH）3 of 70：30 to 99：1 were tested. The results indicate that the obtained ASC mortars are not stable and disintegrate in water. Boric acid was introduced to the mixture to overcome this problem. Stable ASC mortars with high RHA：Al（OH）3 mass ratios of 90：10 to 97.5：2.5 were obtained with the use of boric acid and 115oC curing. The compressive strength of the mortar of 20 MPa was gained. The immersion test indicates that high volume RHA ASC mortars show good resistance in 3vol% H2SO4 solution, but is slightly less durable in 5wt% MgSO4 solution.展开更多
The Al-rich waste with aluminium and hydrocarbon as the major contaminant is generated at the wastewater treatment unit of a polymer processing plant. In this research, the heat treatment of this Al-rich waste and its...The Al-rich waste with aluminium and hydrocarbon as the major contaminant is generated at the wastewater treatment unit of a polymer processing plant. In this research, the heat treatment of this Al-rich waste and its use to adjust the silica/alumina ratio of the high calcium fly ash geopolymer were studied. To recycle the raw Al-rich waste, the waste was dried at 110℃ and calcined at 400 to 1000℃. Mineralogical analyses were conducted using X-ray diffraction （XRD） to study the phase change. The increase in calcination temperature to 600, 800, and 1000℃ resulted in the phase transformation. The more active alumina phase of active θ-Al2O3 was obtained with the increase in calcination temperature. The calcined Al-rich waste was then used as an additive to the fly ash geopolymer by mixing with high calcium fly ash, water glass, 10 M sodium hydroxide （NaOH）, and sand. Test results indicated that the calcined Al-rich waste could be used as an aluminium source to adjust the silica/alumina ratio and the strength of geopolymeric materials. The fly ash geopolymer mortar with 2.5wt% of the Al-rich waste calcined at 1000℃ possessed the 7-d compressive strength of 34.2 MPa.展开更多
This article presents a study on the resistance to chloride penetration, corrosion, porosity, and strength of mortar containing fine fly ash （FA）, ground rice husk-bark ash （RB）, and ground bagasse ash （BA）. Ord...This article presents a study on the resistance to chloride penetration, corrosion, porosity, and strength of mortar containing fine fly ash （FA）, ground rice husk-bark ash （RB）, and ground bagasse ash （BA）. Ordinary Portland cement （CT） was blended with a single pozzolan and two pozzolans. Strength, porosity, rapid chloride penetration, immersion, and corrosion tests were performed to characterize the mortar. Test results showed that the use of ternary blends of CT, FA, and RB or BA decreased the porosity of the mortar, as compared with binary blended mortar containing CT and RB or BA. The resistance to chloride penetration of the mortar improved substantially with partial replacement of CT with FA, RB, and BA. The use of ternary blends of CT, FA and RB or BA produced the mortar with good strength and resistance to chloride penetration. The resistance to chloride penetration was higher with an increase in the replacement level due to the reduced calcium hydroxide.展开更多
The electrical conductivity and dielectric property of fly ash geopolymer pastes in a frequency range of 100 Hz-10 MHz were studied.The effects of the liquid alkali solution to ash ratios（L/A） were analyzed.The mine...The electrical conductivity and dielectric property of fly ash geopolymer pastes in a frequency range of 100 Hz-10 MHz were studied.The effects of the liquid alkali solution to ash ratios（L/A） were analyzed.The mineralogical compositions and microstructures of fly ash geopolymer materials were also investigated using X-ray diffraction（XRD） and scanning electron microscopy（SEM）.The 10 mol sodium hydroxide solution and sodium silicate solution at a sodium silicate-to-sodium hydroxide ratio of 1.0 were used in making geopolymer pastes.The pastes were cured at 40℃.It is found that the electrical conductivity and dielectric constant are dependent on the frequency range and L/A ratios.The conductivity increases but the dielectric constant decreases with increasing frequency.展开更多
基金supported by the Higher Education Research Promotion and National Research University Project of ThailandThailand Research Fund (TRF) under the TRF Senior Research Scholar (No.RTA5480004)the Royal Golden Jubilee Ph.D. Program (No. PHD/0340/2552)
文摘The effect of Portland cement （OPC） addition on the properties of high calcium fly ash geopolymer pastes was investigated in the paper. OPC partially replaced fly ash （FA） at the dosages of 0, 5%, 10%, and 15% by mass of binder. Sodium silicate （Na2SiO3） and sodium hydroxide （NaOH） solutions were used as the liquid portion in the mixture： NaOH 10 mol/L, Na2SiO3/NaOH with a mass ratio of 2.0, and alkaline liquid/binder （L/B） with a mass ratio of 0.6. The curing at 60℃ for 24 h was used to accelerate the geopolymerization. The setting time of all fresh pastes, porosity, and compressive strength of the pastes at the stages of 1, 7, 28, and 90 d were tested. The elastic modulus and strain capacity of the pastes at the stage of 7 d were determined. It is revealed that the use of OPC as an additive to replace part of FA results-in the decreases in the setting time, porosity, and strain capacity of the paste specimens, while the compressive strength and elastic modulus seem to increase.
文摘Owing to the high viscosity of sodium silicate solution, fly ash geopolymer has the problems of low workability and rapid setting time. Therefore, the effect of chemical admixtures on the properties of fly ash geopolymer was studied to overcome the rapid set of the geo-polymer in this paper. High-calcium fly ash and alkaline solution were used as starting materials to synthesize the geopolymer. Calcium chloride, calcium sulfate, sodium sulfate, and sucrose at dosages of 1wt% and 2wt% of fly ash were selected as admixtures based on concrete knowledge to improve the properties of the geopolymer. The setting time, compressive strength, and degree of reaction were recorded, and the microstructure was examined. The results show that calcium chloride significantly shortens both the initial and final setting times of the geopolymer paste. In addition, sucrose also delays the final setting time significantly. The degrees of reaction of fly ash in the geopolymer paste with the admixtures are all higher than those of the control paste. This contributes to the obvious increases in compressive strength.
基金the Commission on Higher Education (MUA) of Thailandthe Sustainable Infrastructure Research and Development Center of Khon Kaen University (SIRDC)Department of Civil Engineering of Rajamangala University of Technology Phra Nakhon (RMUTP)
文摘The effect of grinding on the chemical and physical properties of rice husk ash was studied. Four rice husk ashes with different finenesses, i.e. coarse original rice husk ash （RHA0）, RHA1, RHA2, and RHA3 were used for the study. Ordinary Portland cement （OPC） was partially replaced with rice husk ash at 20% by weight of binder. The water to binder ratio （W/B） of the mortar was maintained at 110%±5% with flow table test. Specific gravity, fineness, chemical properties, compressive strength, and porosity test of mortars were determined. The differences in chemical composition of the rice husk ashes with different finenesses from the same batch are small. The use of RHA3 produces the mortars with good strength and low porosity. The strength of the mortar improves with partial replacement of RHA3 in comparison with normal coarse rice husk ash. The use of RHA3 results in a strong and dense mortar, which is due to the better dispersion and filling effect, as well as an increase in the pozzolanic reaction.
基金supported by the Thailand Research Fund (TRF) under TRF Senior Research Scholar Contact (No.RTA5080020)the Ministry of Education of Thailand through Commission on Higher Education under the Ministry Staff Development Project
文摘The effects of the fineness and shape of fly ash on the porosity and air permeability of cement pastes were investigated. Pulverized coal combustion （PCC） fly ash and fluidized bed coal combustion （FBC） fly ash classified into three different finenesses were used. River sand with particle size distribution similar to that of fly ash was also used for comparison. Portland cement was replaced with fly ash and ground sand at the dosages of 0, 20wt%, and 40wt%. A water-to-binder ratio （w/b） of 0.35 was used throughout the experiment. The results show that the porosity and air permeability of the pastes are influenced by the shape, fineness, and replacement level of fly ash. The porosity and air permeability of FBC fly ash pastes are higher than those of PCC fly ash pastes. This is due to the higher irregular shape and surface of FBC fly ash compared to the spherical shape and relatively smooth surface of PCC fly ash. The porosity increases with the increase in fly ash replacement level and decreases with the increase in its fineness. The permeability of PCC fly ash pastes decreases with the increase in replacement level and fineness, while for FBC fly ash, the permeability increases with the increase in replacement level. Decreases in porosity and permeability are due to a combined effect of the packing of fine particles and the reaction of fly ash.
基金supported by the Thailand Research Fund through the Royal Golden Jubilee Ph.D. Program(No.PHD/0120/2549)
文摘The shrinkage of fly ash geopolymers was studied in the present study.Fly ash was used as the source material for making the geopolymers.The effects of the concentration of NaOH,sodium silicate-to-NaOH ratio,liquid-to-ash ratio,curing temperature,and curing time on shrinkage were investigated.The geopolymers were cured at 25,40,and 60℃,respectively.The results indicate that the shrinkage of geopolymers is strongly dependent on curing temperature and liquid-to-ash ratio.The increase in shrinkage is associated with the low strength development of geopolymers.It is also found that NaOH concentration and sodium silicate-to-NaOH ratio also affect the shrinkage of geopolymers but to a lesser extent.
文摘This paper presented a study on the strength and chloride resistance of mortars made with ternary blends of ordinary Portland cement （OPC）, ground palm oil fuel ash （POA）, and classified fly ash （FA）. The mortar mixtures were made with Portland cement type I containing 0-40wt% FA and POA. FA and POA with 1wt%-3wt% retained on a sieve No.325 were used. The compressive strength and rapid chloride penetration depth of mortars were determined. The results reveal that the use of ternary blended cements produces good strength mortars. The use of the blend of FA and POA also produces high strength mortars and excellent resistance to chloride penetration owing to the synergic effect of FA and POA. A mathematical analysis and two-parameter polynomial model were presented to predict the compressive strength. The mathematical model correlated well with the experimental results. The computer 3-D graphics of strength of the ternary blended mortars were also constructed and could be used to aid the understanding and the proportioning of the blended system.
基金the financial support of the Rajamangala University of Technology Isan, Thailand,for a grant originating from the Strategic Scholarships for Frontier Research Network, which supports the Joint Ph.D. Program and Thai doctoral degreethe Thailand Research Fund (TRF) for financial support originating from the TRF Senior Research Scholarship (No.RTA5480004)the TRF New Researcher Scholarship (No.MRG5280178)
文摘Cellular lightweight concrete （CLC） with the controlled density of approximately 800 kg/m3 was made from a preformed foam, Type-I Portland cement （OPC）, fly ash （FA）, or natural zeolite （NZ）, and its compressive strength, setting time, water absorption, and microstructure of were tested. High-calcium FA and NZ with the median particle sizes of 14.52 and 7.72 μm, respectively, were used to partially replace OPC at 0, 10wt%, 20wt%, and 30wt% of the binder （OPC and pozzolan admixture）. A water-to-binder mass ratio （W/B） of 0.5 was used for all mixes. The testing results indicated that CLC containing 10wt% NZ had the highest compressive strength. The replacement of OPC with NZ decreased the total porosity and air void size but increased the capillary porosity of the CLC. The incorporation of a suitable amount of NZ decreased the setting time, total porosity, and pore size of the paste compared with the findings with the same amount of FA. The total porosity and cumulative pore volume decreased, whereas the gel and capillary pores increased as a result of adding both pozzolans at all replacement levels. The water absorption increased as the capillary porosity increased; this effect depended on the volume of air entrained and the type or amount of pozzolan.
文摘The construction industry is facing a big challenge in reducing the burden it is putting on the environment. There is an urgent need to develop and use eco-efficient construction materials with proper functional performance, a low carbon footprint and a less adverse impact on the environment. Nanotechnology is a new and very promising technology that helps fulfil the need for more environmentally friendly construction materials.
文摘The development of high volume rice husk ash （RHA） alumino silicate composites （ASC） was studied. RHA was used as the source of silica and aluminium in the ASC. The mass ratios of RHA：Al（OH）3 of 70：30 to 99：1 were tested. The results indicate that the obtained ASC mortars are not stable and disintegrate in water. Boric acid was introduced to the mixture to overcome this problem. Stable ASC mortars with high RHA：Al（OH）3 mass ratios of 90：10 to 97.5：2.5 were obtained with the use of boric acid and 115oC curing. The compressive strength of the mortar of 20 MPa was gained. The immersion test indicates that high volume RHA ASC mortars show good resistance in 3vol% H2SO4 solution, but is slightly less durable in 5wt% MgSO4 solution.
基金supported by the Higher Education Research Promotion and National Research University Project of Thailand,Office of the Higher Education Commission, through the Advanced Functional Materials Cluster of Khon Kaen Universitythe Thailand Research Fund (TRF) under TRF Senior Research Scholar contract No.RTA5480004
文摘The Al-rich waste with aluminium and hydrocarbon as the major contaminant is generated at the wastewater treatment unit of a polymer processing plant. In this research, the heat treatment of this Al-rich waste and its use to adjust the silica/alumina ratio of the high calcium fly ash geopolymer were studied. To recycle the raw Al-rich waste, the waste was dried at 110℃ and calcined at 400 to 1000℃. Mineralogical analyses were conducted using X-ray diffraction （XRD） to study the phase change. The increase in calcination temperature to 600, 800, and 1000℃ resulted in the phase transformation. The more active alumina phase of active θ-Al2O3 was obtained with the increase in calcination temperature. The calcined Al-rich waste was then used as an additive to the fly ash geopolymer by mixing with high calcium fly ash, water glass, 10 M sodium hydroxide （NaOH）, and sand. Test results indicated that the calcined Al-rich waste could be used as an aluminium source to adjust the silica/alumina ratio and the strength of geopolymeric materials. The fly ash geopolymer mortar with 2.5wt% of the Al-rich waste calcined at 1000℃ possessed the 7-d compressive strength of 34.2 MPa.
基金financially supported by the Office of the National Research Council of Thailand (NRCT)Higher Education Research Promotion and National Research University Project of Thailand+2 种基金Office of the Higher Education Commission,through the Advanced Functional Materials Cluster of Khon Kaen Universitythe Thailand Research Fund (TRF) under the TRF Senior Research Scholar Contract No. RTA5480004Rajamangala University of Technology Phra Nakhon (RMUTP)
文摘This article presents a study on the resistance to chloride penetration, corrosion, porosity, and strength of mortar containing fine fly ash （FA）, ground rice husk-bark ash （RB）, and ground bagasse ash （BA）. Ordinary Portland cement （CT） was blended with a single pozzolan and two pozzolans. Strength, porosity, rapid chloride penetration, immersion, and corrosion tests were performed to characterize the mortar. Test results showed that the use of ternary blends of CT, FA, and RB or BA decreased the porosity of the mortar, as compared with binary blended mortar containing CT and RB or BA. The resistance to chloride penetration of the mortar improved substantially with partial replacement of CT with FA, RB, and BA. The use of ternary blends of CT, FA and RB or BA produced the mortar with good strength and resistance to chloride penetration. The resistance to chloride penetration was higher with an increase in the replacement level due to the reduced calcium hydroxide.
基金supported by the Thailand Research Fund through the Royal Golden Jubilee Ph.D. Program(No.PHD/0359/2550)
文摘The electrical conductivity and dielectric property of fly ash geopolymer pastes in a frequency range of 100 Hz-10 MHz were studied.The effects of the liquid alkali solution to ash ratios（L/A） were analyzed.The mineralogical compositions and microstructures of fly ash geopolymer materials were also investigated using X-ray diffraction（XRD） and scanning electron microscopy（SEM）.The 10 mol sodium hydroxide solution and sodium silicate solution at a sodium silicate-to-sodium hydroxide ratio of 1.0 were used in making geopolymer pastes.The pastes were cured at 40℃.It is found that the electrical conductivity and dielectric constant are dependent on the frequency range and L/A ratios.The conductivity increases but the dielectric constant decreases with increasing frequency.
