This study investigated the mechanical responses and debonding mechanisms of a bolt-resin-rock composite anchoring sys-tem subjected to cyclic shear loading.A systematic analysis was conducted on the effects of the in...This study investigated the mechanical responses and debonding mechanisms of a bolt-resin-rock composite anchoring sys-tem subjected to cyclic shear loading.A systematic analysis was conducted on the effects of the initial normal load(Fsd),cyclic shear dis-placement amplitude(ud),frequency(f),and rock type on the shear load,normal displacement,shear wear characteristics,and strain field evolution.The experimental results showed that as Fsd increased from 7.5 to 120 kN,both the peak and residual shear loads exhibited in-creasing trends,with increments ranging from 1.98%to 35.25%and from 32.09%to 86.74%,respectively.The maximum shear load of each cycle declined over the cyclic shear cycles,with the rate of decrease slowing and stabilizing,indicating that shear wear primarily oc-curred at the initial cyclic shear stage.During cyclic shearing,the normal displacement decreased spirally with the shear displacement,im-plying continuous shear contraction.The spiral curves display sparse upwards and dense downward trends,with later cycles dominated by dynamic sliding along the pre-existing shear rupture surface,which is particularly evident in coal.The bearing capacity of the anchoring system varies with the rock type and is governed by the coal strength in coal,resin-rock bonding in sandstone#1 and sandstone#2,com-bined resin strength and resin-rock bonding in sandstone#3(sandstone#1,sandstone#2 and sandstone#3,increasing strength order),and resin strength and bolt-resin bonding in limestone.Cyclic shear loading induces anisotropic interfacial degradation,characterized by es-calating strain concentrations and predominant resin-rock interface debonding,with the damage severity modulated by the rock type.展开更多
Understanding the shear mechanical behaviors and instability mechanisms of rock joints under dynamic loading remains a complex challenge.This research conducts a series of direct shear tests on real rock joints subjec...Understanding the shear mechanical behaviors and instability mechanisms of rock joints under dynamic loading remains a complex challenge.This research conducts a series of direct shear tests on real rock joints subjected to cyclic normal loads to assess the influence of dynamic normal loading amplitude(F_(d)),dynamic normal loading frequency(f_(v)),initial normal loading(F_(s)),and the joint roughness coefficient(JRC)on the mechanical properties and instability responses of these joints.The results show that unstable sliding is often accompanied by friction weakening due to dynamic normal loads.A significant negative correlation exists between cyclic normal loads and the normal displacement during the shearing process.Dynamic normal load paths vary the contact states of asperities on the rough joint surfaces,impacting the stick-slip instability mechanism of the joints,which in turn affects both the magnitude and location of the stress drop during the stick-slip events,particularly during the unloading phases.An increasing F_(d) results in a more stable shearing behavior and a reduction in the amplitude of stick-slip stress drops.The variation in f_(v) influences the amplitude of stress drop for the joints during shear,characterized by an initial decrease(f_(v)=0.25-2 Hz)before exhibiting an increment(f_(v)=2-4 Hz).As F_(s) increases,sudden failures of the interlocked rough surfaces are more prone to occur,thus producing enhanced instability and a more substantial stress drop.Additionally,a larger JRC intensifies the instability of the joints,which would induce a more pronounced decline in the stick-slip stress.The Rate and state friction(RSF)law can provide an effective explanation for the unstable sliding phenomena of joints during the oscillations of normal loads.The findings may provide certain useful references for a deeper comprehension of the sliding behaviors exhibited by rock joints when subjected to cyclic dynamic disturbances.展开更多
Under external disturbances,the shear mechanical responses and debonding failure mechanisms at anisotropic interfaces of anchoring system composed of multiphase media are inherently difficult to characterize due to th...Under external disturbances,the shear mechanical responses and debonding failure mechanisms at anisotropic interfaces of anchoring system composed of multiphase media are inherently difficult to characterize due to the concealment nature of interfacial interactions.This study establishes an equivalent shear model for a bolt-resin-rock anchoring system and conducts direct shear tests under dynamic normal load(DNL)boundary from both laboratory experiments and discrete element method(DEM)simulations.The research investigates the influence of normal dynamic load amplitude(An)and rock type on shear strength parameters,elucidating the evolutionary characteristics and underlying mechanisms of shear load and normal displacement fluctuations induced by cyclic normal loading,with maximum shear load decreasing by 36.81%to 46.94%as An increases from 10%to 70%when rock type varies from coal to limestone.Through analysis of strain field evolution,the critical impact of rock type on localization of shear failure surface is revealed,with systematic summarization of differentiated wear characteristics,failure modes,and key controlling factors associated with shear failure surface.Mesoscopic investigations enabled by DEM simulations uncover the nonuniform distribution of contact force chains within the material matrix and across the anisotropic interfaces under various DNL boundaries,clarify rock type dependent crack propagation pathways,and quantitatively assess the damage extent of shear failure surface,with the anisotropic interface damage factor increasing from 34.9%to 56.6%as An rises from 10%to 70%,and decreasing from 49.6%to 23.4%as rock type varies from coal to limestone.展开更多
Rockburst precursors are critical for disaster warning,yet the complexity of rockburst has hindered the identification of a unified precursor.Furthermore,the influence of loading rates(LRs)on acoustic emission(AE)prec...Rockburst precursors are critical for disaster warning,yet the complexity of rockburst has hindered the identification of a unified precursor.Furthermore,the influence of loading rates(LRs)on acoustic emission(AE)precursors in different rock types remains poorly understood.This study investigates the AE characteristics and early warning times of rockburst in slate and mica-schist under four LRs(0.05,0.15,0.25,and 0.5 MPa/s)using true triaxial unloading tests.The micro-crack state of the samples was evaluated using entropy,while critical slowing down(CSD)theory was applied to interpret AE precursors.The results reveal that as the LR increases,the rockburst stress of both rocks initially rises and then declines,with mica-schist exhibiting more severe damage and a higher dominance of tensile cracks.Notably,identifying rockburst precursors in mica-schist proved more challenging compared to slate.Among the methods tested,AE amplitude variance outperformed entropy in precursor identification.Additionally,the rockburst early warning time was found to be negatively correlated with the LR,with mica-schist consistently showing shorter warning times than slate.The CSD-derived precursor,due to its enhanced sensitivity,is recommended for early warning systems.These findings provide new insights into the role of LRs in rockburst dynamics and offer practical guidance for improving precursor identification and disaster mitigation strategies.展开更多
In rock engineering,the cyclic shear characteristics of rough joints under dynamic disturbances are still insufficiently studied.This study conducted cyclic shear experiments on rough joints under dynamic normal loads...In rock engineering,the cyclic shear characteristics of rough joints under dynamic disturbances are still insufficiently studied.This study conducted cyclic shear experiments on rough joints under dynamic normal loads to assess the impact of shear frequency(f_(h))and shear displacement amplitude(u_(d))on the frictional properties of the joint.The results reveal that within a single shearing cycle,the normal displacement negatively correlates with the dynamic normal force.As the shear cycle number increases,the joint surface undergoes progressive wear,resulting in an exponential decrease in the peak normal displacement.In the cyclic shearing procedure,the forward peak values of shear force and friction coefficient display larger fluctuations at either lower or higher shear frequencies.However,under moderate shear frequency conditions,the changes in the shear strength of the joint surface are smaller,and the degree of degradation post-shearing is relatively limited.As the shear displacement amplitude increases,the range of normal deformation within the joint widens.Furthermore,after shearing,the corresponding joint roughness coefficient trend shows a gradual decrease with an increasing shear displacement amplitude,while varying with the shearing frequency in a pattern that initially rises and then falls,with a turning point at 0.05 Hz.The findings of this research contribute to a profound comprehension of the cyclic frictional properties of rock joints under dynamic disturbances.展开更多
With the third innovation in science and technology worldwide, China has also experienced thismarvelous progress. Concerning the longwall mining in China, the ＂masonry beam theory＂ （MBT） wasfirst proposed in the 1...With the third innovation in science and technology worldwide, China has also experienced thismarvelous progress. Concerning the longwall mining in China, the ＂masonry beam theory＂ （MBT） wasfirst proposed in the 1960s, illustrating that the transmission and equilibrium method of overburdenpressure using reserved coal pillar in mined-out areas can be realized. This forms the so-called ＂121mining method＂, which lays a solid foundation for development of mining science and technology inChina. The ＂transfer rock beam theory＂ （TRBT） proposed in the 1980s gives a further understanding forthe transmission path of stope overburden pressure and pressure distribution in high-stress areas. In thisregard, the advanced 121 mining method was proposed with smaller coal pillar for excavation design,making significant contributions to improvement of the coal recovery rate in that era. In the 21st century,the traditional mining technologies faced great challenges and, under the theoretical developmentspioneered by Profs. Minggao Qian and Zhenqi Song, the ＂cutting cantilever beam theory＂ （CCBT） wasproposed in 2008. After that the 110 mining method is formulated subsequently, namely one stope face,after the first mining cycle, needs one advanced gateway excavation, while the other one is automaticallyformed during the last mining cycle without coal pillars left in the mining area. This method can beimplemented using the CCBT by incorporating the key technologies, including the directional presplittingroof cutting, constant resistance and large deformation （CRLD） bolt/anchor supporting systemwith negative Poisson＇s ratio （NPR） effect material, and remote real-time monitoring technology. TheCCBT and 110 mining method will provide the theoretical and technical basis for the development ofmining industry in China.展开更多
Rockburst is becoming a huge challenge for the utilization of deep underground space.Extensive efforts have been devoted to investigating the rockburst behavior and mechanism experimentally,theoretically,and numerical...Rockburst is becoming a huge challenge for the utilization of deep underground space.Extensive efforts have been devoted to investigating the rockburst behavior and mechanism experimentally,theoretically,and numerically.The aim of this review is to discuss the novel development and the state-of-the-art in experimental techniques,theories,and numerical approaches proposed for rockburst.The definition and classification of rockburst are first summarized with an in-depth comparison among them.Then,the available laboratory experimental technologies for rockburst are reviewed in terms of indirect and direct approaches,with the highlight of monitoring technologies and data analysis methods.Some key rockburst influencing factors(i.e.size and shape,rock types,stress state,water content,and temperature)are analyzed and discussed based on collected data.After that,rockburst theories and mechanisms are discussed and evaluated,as well as the microscopic observation.The simulation approaches of rockburst are also summarized with the highlight of optional novel numerical methods.The accuracy,stability,and reliability of different experimental,theoretical and numerical approaches are also compared and assessed in each part.Finally,a summary and some aspects of prospective research are presented.展开更多
Quasi-NPR(negative Poisson’s ratio)steel is a new type of super bolt material with high strength,high ductility,and a micro-negative Poisson’s effect.This material overcomes the contrasting characteristics of the hi...Quasi-NPR(negative Poisson’s ratio)steel is a new type of super bolt material with high strength,high ductility,and a micro-negative Poisson’s effect.This material overcomes the contrasting characteristics of the high strength and high ductility of steel and it has significant energy-absorbing characteristics,which is of high value in deep rock and soil support engineering.However,research on the shear resistance of quasi-NPR steel has not been carried out.To study the shear performance of quasi-NPR steel bolted rock joints,indoor shear tests of bolted rock joints under different normal stress conditions were carried out.Q235 steel and#45 steel,two representative ordinary bolt steels,were set up as a control group for comparative tests to compare and analyze the shear strength,deformation and instability mode,shear energy absorption characteristics,and bolting contribution of different types of bolts.The results show that the jointed rock masses without bolt reinforcement undergo brittle failure under shear load,while the bolted jointed rock masses show obvious ductile failure characteristics.The shear deformation ca-pacity of quasi-NPR steel is more than 3.5 times that of Q235 steel and#45 steel.No fracture occurs in the quasi-NPR steel during large shear deformation and it can provide stable shear resistance.However,the other two types of control bolts become fractured under the same conditions.Quasi-NPR steel has significant energy-absorbing characteristics under shear load and has obvious advantages in terms of absorbing the energy released by shear deformation of jointed rock masses as compared with ordinary steel.In particular,the shear force plays a major role in resisting the shear deformation of Q235 steel and#45 steel,therefore,fracture failure occurs under small bolt deformation.However,the axial force of quasi-NPR steel can be fully exerted when resisting joint shear deformation;the steel itself does not break when large shear deformation occurs,and the supporting effect of the jointed rock mass is effectively guaranteed.展开更多
With the increasing exploitation scope and intensity,the shallow resources would be exhausted in the future;and the deep mining will become an essential choice.In deep tunnel engineering,the heat-harm becomes one of t...With the increasing exploitation scope and intensity,the shallow resources would be exhausted in the future;and the deep mining will become an essential choice.In deep tunnel engineering,the heat-harm becomes one of the mainbariers.Investigations on high temperature coal mine have been done in Nothem China,with the construting of threemodels of high temperature mines suffering heat-harm,at the Jiahe mine,Sanhejian mine and Zhangshuanglou mine.Thedomestic and abroad cooling technologies of the mine respectively are also summarized after comparatively analyzing theadvantages and disadvantages of each technology.Finally,we find that the high temperature exchange machinery system(HEMS)technology that use mine discharge as the cold source,is excellent to heat-ham control in deep mines.Taking theJiahe coal mine as an example,we systematically introduce this teclnology by disposing three main workstations.HEMStechnology with its operations and functions in different exploitation levels are accomplished,including the extraction ofrefrigerating output,the transportation of chilled water by closed circulation line,the decompression of circulation linesand equipment by pressure transformation machine,and the heat exchange and cooling of workplace by heat exchangebetween wind stream and the chilled water.The exchanged heat source from the workplace is taken to ground heating bythe circulating water which acts as a carrier.It shows that the HEMS-technology benefit in environment protection andemission reduction.Results of this project illustrate that it is efficient in heat-ham control with the temperature decrease ofthe workplace down to 26-29℃,and being 4-6℃ lower than the original,and the relative humidity 5%-15%lowerthan before.It greatly improves the working environment of underground workplace suffering heat-ham of high tem-perature and high humidity.In addition,by the extracting of deep geothermal enery,ground fired boiler for heating hasbeen replaced,reducing environmental pollution.This technology is worth generalization in deep mines and related fields.展开更多
The 2008 Wenchuan earthquake resulted in a large number of fatalities and caused significant economic losses.Thousands of landslides,many of which are very large,were triggered by the earthquake.A majority of catastro...The 2008 Wenchuan earthquake resulted in a large number of fatalities and caused significant economic losses.Thousands of landslides,many of which are very large,were triggered by the earthquake.A majority of catastrophic landslides were distributed along the central Longmenshan fault system,at the eastern margin of the Tibetan Plateau.Some of the landslides resulted in sudden damming of rivers causing flooding,which in turn induced secondary sliding disasters.Among the most significant landslides,the Daguangbao landslide was the largest in volume with the maximum thickness.For this,a numerical model of the Daguangbao landslide,using the material point method(MPM),was developed to simulate the interaction of the seismic loads imposed on the slope.The numerical results then are compared with the post-earthquake profile.As a consequence of the landslide,a nearly vertical head scarp with a maximum height of about 700 m was generated.This is considered as a high risk situation that requires constant monitoring and evaluation.Finally,we propose a methodology based on Bayesian networks(BNs)to manage the risk associated with the stability of the rockwall at the Daguangbao landslide site.展开更多
2G-NPR bolt (the 2nd generation Negative Poisson’s Ratio bolt) is a new type of bolt with high strength, high toughness and no yield platform. It has signifcant efects on improving the shear strength of jointed rock ...2G-NPR bolt (the 2nd generation Negative Poisson’s Ratio bolt) is a new type of bolt with high strength, high toughness and no yield platform. It has signifcant efects on improving the shear strength of jointed rock mass and controlling the stability of surrounding rock. To achieve an accurate simulation of bolted joint shear tests, we have studied a numerical simulation method that takes into account the 2G-NPR bolt's tensile–shear fracture criterion. Firstly, the indoor experimental study on the tensile–shear mechanical properties of 2G-NPR bolt is carried out to explore its mechanical properties under diferent tensile–shear angles, and the fracture criterion of 2G-NPR bolt considering the tensile–shear angle is established. Then, a three-dimensional numerical simulation method considering the tensile–shear mechanical constitutive and fracture criterion of 2G-NPR bolt, the elastoplastic mechanical behavior of surrounding rock and the damage and deterioration of grouting body is proposed. The feasibility and accuracy of the method are verifed by comparing with the indoor shear test results of 2G-NPR bolt anchorage joints. Finally, based on the numerical simulation results, the deformation and stress of the bolt, the distribution of the plastic zone of the rock mass, the stress distribution and the damage of the grouting body are analyzed in detail. The research results can provide a good reference value for the practical engineering application and shear mechanical performance analysis of 2G-NPR bolt.展开更多
The use of explosives is restricted on some important holidays,and the handling of unexploded charge is very dangerous.Therefore,an innovative non-explosive technology called instantaneous expansion(IE)was developed f...The use of explosives is restricted on some important holidays,and the handling of unexploded charge is very dangerous.Therefore,an innovative non-explosive technology called instantaneous expansion(IE)was developed for tunneling.IE,whose components are derived from solid wastes such as coal gangue and straw conduces to realizing the reuse of waste.Moreover,its cost is lower than explosives.Blind guns of IE are easy to treat with water.The IE tunneling method is classified into two categories,i.e.IE with a single fracture(IESF)and IE with multiple fractures(IEMF),which are used to form the tunnel crosssection directionally cross-section and to fragment the rocks inside the cross-section,respectively.In this study,the principle of IE tunneling was elaborated first.Then,tunneling experiments and numerical simulations were performed on IE,conventional blasting(CB)and shaped charge blasting(SCB)in comparison.The experimental and numerical results show that IE achieved the best performance of directional rock breaking and corresponded to the most minor excavation-induced damage zone of the surrounding rock.Besides,the tunnel cross-section created by IE was flat and smooth.Comparing IE with CB and SCB,the over/under-excavation area decreased by 64%and 17%,and the excavation-induced damage zone fell by 26%and 11%,respectively.The range of the loose circle is reduced,which is conducive to improving the long-term stability of the roadway.The research provides a safe and economical tunneling method with excellent application prospects.展开更多
To investigate the mechanism of rockburst prevention by spraying water onto the surrounding rocks,15 experiments are performed considering different water absorption levels on a single face.High-speed photography and ...To investigate the mechanism of rockburst prevention by spraying water onto the surrounding rocks,15 experiments are performed considering different water absorption levels on a single face.High-speed photography and acoustic emission(AE)system are used to monitor the rockburst process.The effect of water on sandstone rockburst and the prevention mechanism of water on sandstone rockburst are analyzed from the perspective of energy and failure mode.The results show that the higher the ab-sorption degree,the lower the intensity of the rockburst after absorbing water on single side of sand-stone.This is reflected in the fact that with the increase in the water absorption level,the ejection velocity of rockburst fragments is smaller,the depth of the rockburst pit is shallower,and the AE energy is smaller.Under the water absorption level of 100%,the magnitude of rockburst intensity changes from medium to slight.The prevention mechanism of water on sandstone rockburst is that water reduces the capacity of sandstone to store strain energy and accelerates the expansion of shear cracks,which is not conducive to the occurrence of plate cracking before rockburst,and destroys the conditions for rockburst incubation.展开更多
Given the challenges in managing large deformation disasters in energy engineering,traffic tunnel engineering,and slope engineering,the excavation compensation theory has been proposed for large deformation disasters ...Given the challenges in managing large deformation disasters in energy engineering,traffic tunnel engineering,and slope engineering,the excavation compensation theory has been proposed for large deformation disasters and the supplementary technology system is developed accordingly.This theory is based on the concept that“all destructive behaviors in tunnel engineering originate from excavation.”This paper summarizes the development of the excavation compensation theory in five aspects:the“theory,”“equipment,”“technology,”the design method with large deformation mechanics,and engineering applications.First,the calculation method for compensation force has been developed based on this theory,and a comprehensive large deformation disaster control theory system is formed.Second,a negative Poisson's ratio anchor cable with high preload,large deformation,and super energy absorption characteristics has been independently developed and applied to large deformation disaster control.An intelligent tunnel monitoring and early warning cloud platform system are established for remote monitoring and early warning system of Newton force in landslide geological hazards.Third,the double gradient advance grouting technology,the two-dimensional blasting technology,and the integrated Newton force monitoring--early warning--control technology are developed for different engineering environments.Finally,some applications of this theory in China's energy,traffic tunnels,landslide,and other field projects have been analyzed,which successfully demonstrates the capability of this theory in large deformation disaster control.展开更多
The most common method used to describe earthquake activity is based on the changes in physical parameters of the earth's surface such as displacement of active fault and seismic wave.However,such approach is not ...The most common method used to describe earthquake activity is based on the changes in physical parameters of the earth's surface such as displacement of active fault and seismic wave.However,such approach is not successful in forecasting the movement behaviors of faults.In the present study,a new mechanical model of fault activity,considering the shear strength on the fault plane and the influence of the resistance force,is established based on the occurrence condition of earthquake.A remote real-time monitoring system is correspondingly developed to obtain the changes in mechanical components within fault.Taking into consideration the local geological conditions and the history of fault activity in Zhangjiakou of China,an active fault exposed in the region of Zhangjiakou is selected to be directly monitored by the real-time monitoring technique.A thorough investigation on local fault structures results in the selection of two suitable sites for monitoring potential active tectonic movements of Zhangjiakou fault.Two monitoring curves of shear strength,recorded during a monitoring period of 6 months,turn out to be steady,which indicates that the potential seismic activities hardly occur in the adjacent region in the near future.This monitoring technique can be used for early-warning prediction of the movement of active fault,and can help to further gain an insight into the interaction between fault activity and relevant mechanisms.展开更多
This study aims to investigate mechanical properties and failure mechanisms of layered rock with rough joint surfaces under direct shear loading.Cubic layered samples with dimensions of 100 mm×100 mm×100 mm ...This study aims to investigate mechanical properties and failure mechanisms of layered rock with rough joint surfaces under direct shear loading.Cubic layered samples with dimensions of 100 mm×100 mm×100 mm were casted using rock-like materials,with anisotropic angle(α)and joint roughness coefficient(JRC)ranging from 15°to 75°and 2-20,respectively.The direct shear tests were conducted under the application of initial normal stress(σ_(n)) ranging from 1-4 MPa.The test results indicate significant differences in mechanical properties,acoustic emission(AE)responses,maximum principal strain fields,and ultimate failure modes of layered samples under different test conditions.The peak stress increases with the increasingαand achieves a maximum value atα=60°or 75°.As σ_(n) increases,the peak stress shows an increasing trend,with correlation coefficients R² ranging from 0.918 to 0.995 for the linear least squares fitting.As JRC increases from 2-4 to 18-20,the cohesion increases by 86.32%whenα=15°,while the cohesion decreases by 27.93%whenα=75°.The differences in roughness characteristics of shear failure surface induced byαresult in anisotropic post-peak AE responses,which is characterized by active AE signals whenαis small and quiet AE signals for a largeα.For a given JRC=6-8 andσ_(n)=1 MPa,asαincreases,the accumulative AE counts increase by 224.31%(αincreased from 15°to 60°),and then decrease by 14.68%(αincreased from 60°to 75°).The shear failure surface is formed along the weak interlayer whenα=15°and penetrates the layered matrix whenα=60°.Whenα=15°,as σ_(n) increases,the adjacent weak interlayer induces a change in the direction of tensile cracks propagation,resulting in a stepped pattern of cracks distribution.The increase in JRC intensifies roughness characteristics of shear failure surface for a smallα,however,it is not pronounced for a largeα.The findings will contribute to a better understanding of the mechanical responses and failure mechanisms of the layered rocks subjected to shear loads.展开更多
High geo-temperature is one of the inevitable geological disasters in deep engineering such as resource extraction,space development,and energy utilization.One of the key issues is to understand the mechanical propert...High geo-temperature is one of the inevitable geological disasters in deep engineering such as resource extraction,space development,and energy utilization.One of the key issues is to understand the mechanical properties and failure mechanism of high-temperature rock disturbed by low-temperature airflow after excavation.Therefore,.the experimental and numerical investigation were carried out to study the impact of cooling rate on mechanical properties and failure mechanism of high temperature sandstone.First,uniaxial compression experiments of high temperature sandstone at different real-time cooling rates were carried out to study the mechanical properties and failure modes.The experimental results indicate that the cooling rate has a significant effect on the mechanical properties and failure modes of sandstone.The peak strain,peak stress,and elastic modulus decrease with an increase in cooling rate,and the fragmentation degree after failure increases gradually.Moreover,the equivalent numerical model of heterogeneous sandstone was established using particle flow code(PFC)to reveal the failure mechanism.The results indicate that the sandstone is dominated by intragrain failure in the cooling stage,the number of microcracks is exponentially related to the cooling rate,and the higher the cooling rate,the more cracks are concentrated in the exterior region.Under axial loading,the tensile stress is mostly distributed along the radial direction,and the damage in the cooling stage is mostly due to the fracture of the radial bond.In addition,axial loading,temperature gradient and thermal stress mismatch between adjacent minerals are the main reasons for the damage of sandstone in the cooling stage.Moreover,the excessive temperature gradient in the exterior region of the sandstone is the main reason for the damage concentration in this region.展开更多
A nuclear explosion in the rock mass medium can produce strong shock waves,seismic shocks,and other destructive effects,which can cause extreme damage to the underground protection infrastructures.With the increase in...A nuclear explosion in the rock mass medium can produce strong shock waves,seismic shocks,and other destructive effects,which can cause extreme damage to the underground protection infrastructures.With the increase in nuclear explosion power,underground protection engineering enabled by explosion-proof impact theory and technology ushered in a new challenge.This paper proposes to simulate nuclear explosion tests with on-site chemical explosion tests in the form of multi-hole explosions.First,the mechanism of using multi-hole simultaneous blasting to simulate a nuclear explosion to generate approximate plane waves was analyzed.The plane pressure curve at the vault of the underground protective tunnel under the action of the multi-hole simultaneous blasting was then obtained using the impact test in the rock mass at the site.According to the peak pressure at the vault plane,it was divided into three regions:the stress superposition region,the superposition region after surface reflection,and the approximate plane stress wave zone.A numerical simulation approach was developed using PFC and FLAC to study the peak particle velocity in the surrounding rock of the underground protective cave under the action of multi-hole blasting.The time-history curves of pressure and peak pressure partition obtained by the on-site multi-hole simultaneous blasting test and numerical simulation were compared and analyzed,to verify the correctness and rationality of the formation of an approximate plane wave in the simulated nuclear explosion.This comparison and analysis also provided a theoretical foundation and some research ideas for the ensuing study on the impact of a nuclear explosion.展开更多
Rockburst are often encountered in tunnel construction due to the complex geological conditions.To study the influence of unloading rate on rockburst,gneiss rockburst experiments were conducted under three groups of u...Rockburst are often encountered in tunnel construction due to the complex geological conditions.To study the influence of unloading rate on rockburst,gneiss rockburst experiments were conducted under three groups of unloading rates.A high-speed photography system and acoustic emission(AE)system were used to monitor the entire process of rockburst process in real-time.The results show that the intensity of gneiss rockburst decreases with decrease of unloading rate,which is manifested as the reduction of AE energy and fragments ejection velocity.The mechanisms are proposed to explain this effect:(i)The reduction of unloading rate changes the crack propagation mechanism in the process of rockburst.This makes the rockbursts change from the tensile failure mechanism at high unloading rate to the tension-shear mixed failure mechanism at low unloading rate,and more energy released in the form of shear crack propagation.Then,less strain energy is converted into kinetic energy of fragments ejection.(ii)Less plate cracking degree of gneiss has taken shape due to decrease of unloading rate,resulting in the destruction of rockburst incubation process.The enlightenments of reducing the unloading rate for the project are also described quantitatively.The rockburst magnitude is reduced from the medium magnitude at the unloading rate of 0.1 MPa/s to the slight magnitude at the unloading rate of 0.025 MPa/s,which was judged by the ejection velocity.展开更多
Rock and geotechnical engineering investigations involve drilling holes in ground with or without retrieving soil and rock samples to construct the subsurface ground profile.On the basis of an actual soil nailing dril...Rock and geotechnical engineering investigations involve drilling holes in ground with or without retrieving soil and rock samples to construct the subsurface ground profile.On the basis of an actual soil nailing drilling for a slope stability project in Hong Kong,this paper further develops the drilling process monitoring(DPM)method for digitally profiling the subsurface geomaterials of weathered granitic rocks using a compressed airflow driven percussive-rotary drilling machine with down-the-hole(DTH)hammer.Seven transducers are installed on the drilling machine and record the chuck displacement,DTH rotational speed,and five pressures from five compressed airflows in real-time series.The mechanism and operations of the drilling machine are elaborated in detail,which is essential for understanding and evaluating the drilling data.A MATLAB program is developed to automatically filter the recorded drilling data in time series and classify them into different drilling processes in sub-time series.These processes include penetration,push-in with or without rod,pull-back with or without rod,rod-tightening and rod-untightening.The drilling data are further reconstructed to plot the curve of drill-bit depth versus the net drilling time along each of the six drillholes.Each curve is found to contain multiple linear segments with a constant penetration rate,which implies a zone of homogenous geomaterial with different weathering grades.The effect from fluctuation of the applied pressures is evaluated quantitatively.Detailed analyses are presented for accurately assess and verify the underground profiling and strength in weathered granitic rock,which provided the basis of using DPM method to confidently assess drilling measurements to interpret the subsurface profile in real time.展开更多
基金The financial support from the National Natural Science Foundation of China(Nos.52174092,42472338,and 51904290)the Natural Science Foundation of Jiangsu Province,China(No.BK20220157)+1 种基金the Fundamental Research Funds for the Central Universities,China(No.2022YCPY0202)the Open Fund of Key Laboratory of Safety and High-efficiency Coal Mining,Ministry of Education(Anhui University of Science and Technology)(No.JYBSYS202311)。
文摘This study investigated the mechanical responses and debonding mechanisms of a bolt-resin-rock composite anchoring sys-tem subjected to cyclic shear loading.A systematic analysis was conducted on the effects of the initial normal load(Fsd),cyclic shear dis-placement amplitude(ud),frequency(f),and rock type on the shear load,normal displacement,shear wear characteristics,and strain field evolution.The experimental results showed that as Fsd increased from 7.5 to 120 kN,both the peak and residual shear loads exhibited in-creasing trends,with increments ranging from 1.98%to 35.25%and from 32.09%to 86.74%,respectively.The maximum shear load of each cycle declined over the cyclic shear cycles,with the rate of decrease slowing and stabilizing,indicating that shear wear primarily oc-curred at the initial cyclic shear stage.During cyclic shearing,the normal displacement decreased spirally with the shear displacement,im-plying continuous shear contraction.The spiral curves display sparse upwards and dense downward trends,with later cycles dominated by dynamic sliding along the pre-existing shear rupture surface,which is particularly evident in coal.The bearing capacity of the anchoring system varies with the rock type and is governed by the coal strength in coal,resin-rock bonding in sandstone#1 and sandstone#2,com-bined resin strength and resin-rock bonding in sandstone#3(sandstone#1,sandstone#2 and sandstone#3,increasing strength order),and resin strength and bolt-resin bonding in limestone.Cyclic shear loading induces anisotropic interfacial degradation,characterized by es-calating strain concentrations and predominant resin-rock interface debonding,with the damage severity modulated by the rock type.
基金funding support from the National Natural Science Foundation of China(Grant Nos.52174092,and 51904290)open fund of Key Laboratory of Safety and High-efficiency Coal Mining,Ministry of Education(Anhui University of Science and Technology)(Grant No.JYBSYS202311).
文摘Understanding the shear mechanical behaviors and instability mechanisms of rock joints under dynamic loading remains a complex challenge.This research conducts a series of direct shear tests on real rock joints subjected to cyclic normal loads to assess the influence of dynamic normal loading amplitude(F_(d)),dynamic normal loading frequency(f_(v)),initial normal loading(F_(s)),and the joint roughness coefficient(JRC)on the mechanical properties and instability responses of these joints.The results show that unstable sliding is often accompanied by friction weakening due to dynamic normal loads.A significant negative correlation exists between cyclic normal loads and the normal displacement during the shearing process.Dynamic normal load paths vary the contact states of asperities on the rough joint surfaces,impacting the stick-slip instability mechanism of the joints,which in turn affects both the magnitude and location of the stress drop during the stick-slip events,particularly during the unloading phases.An increasing F_(d) results in a more stable shearing behavior and a reduction in the amplitude of stick-slip stress drops.The variation in f_(v) influences the amplitude of stress drop for the joints during shear,characterized by an initial decrease(f_(v)=0.25-2 Hz)before exhibiting an increment(f_(v)=2-4 Hz).As F_(s) increases,sudden failures of the interlocked rough surfaces are more prone to occur,thus producing enhanced instability and a more substantial stress drop.Additionally,a larger JRC intensifies the instability of the joints,which would induce a more pronounced decline in the stick-slip stress.The Rate and state friction(RSF)law can provide an effective explanation for the unstable sliding phenomena of joints during the oscillations of normal loads.The findings may provide certain useful references for a deeper comprehension of the sliding behaviors exhibited by rock joints when subjected to cyclic dynamic disturbances.
基金support from the National Natural Science Foundation of China(Nos.51504247,52174092,51904290,and 52074259)the Natural Science Foundation of Jiangsu Province,China(No.BK20220157)+1 种基金the Fundamental Research Funds for the Central Universities,China(No.2022YCPY0202)the China University of Mining and Technology(CUMT)Open Sharing Fund for Large-scale Instruments and Equipment(No.DYGX-2025-47)is gratefully acknowledged.
文摘Under external disturbances,the shear mechanical responses and debonding failure mechanisms at anisotropic interfaces of anchoring system composed of multiphase media are inherently difficult to characterize due to the concealment nature of interfacial interactions.This study establishes an equivalent shear model for a bolt-resin-rock anchoring system and conducts direct shear tests under dynamic normal load(DNL)boundary from both laboratory experiments and discrete element method(DEM)simulations.The research investigates the influence of normal dynamic load amplitude(An)and rock type on shear strength parameters,elucidating the evolutionary characteristics and underlying mechanisms of shear load and normal displacement fluctuations induced by cyclic normal loading,with maximum shear load decreasing by 36.81%to 46.94%as An increases from 10%to 70%when rock type varies from coal to limestone.Through analysis of strain field evolution,the critical impact of rock type on localization of shear failure surface is revealed,with systematic summarization of differentiated wear characteristics,failure modes,and key controlling factors associated with shear failure surface.Mesoscopic investigations enabled by DEM simulations uncover the nonuniform distribution of contact force chains within the material matrix and across the anisotropic interfaces under various DNL boundaries,clarify rock type dependent crack propagation pathways,and quantitatively assess the damage extent of shear failure surface,with the anisotropic interface damage factor increasing from 34.9%to 56.6%as An rises from 10%to 70%,and decreasing from 49.6%to 23.4%as rock type varies from coal to limestone.
基金supported by the National Natural Science Foundation of China(Nos.52374119,42477142 and 42277154)Natural Science Foundation of Jiangsu Province(No.BK20242059)+1 种基金the open fund of State Key Laboratory of Hydraulics and Mountain River Engineering(No.SKHL2306)the High-level Talent Introduction Project of Changzhou University(No.ZMF24020037)。
文摘Rockburst precursors are critical for disaster warning,yet the complexity of rockburst has hindered the identification of a unified precursor.Furthermore,the influence of loading rates(LRs)on acoustic emission(AE)precursors in different rock types remains poorly understood.This study investigates the AE characteristics and early warning times of rockburst in slate and mica-schist under four LRs(0.05,0.15,0.25,and 0.5 MPa/s)using true triaxial unloading tests.The micro-crack state of the samples was evaluated using entropy,while critical slowing down(CSD)theory was applied to interpret AE precursors.The results reveal that as the LR increases,the rockburst stress of both rocks initially rises and then declines,with mica-schist exhibiting more severe damage and a higher dominance of tensile cracks.Notably,identifying rockburst precursors in mica-schist proved more challenging compared to slate.Among the methods tested,AE amplitude variance outperformed entropy in precursor identification.Additionally,the rockburst early warning time was found to be negatively correlated with the LR,with mica-schist consistently showing shorter warning times than slate.The CSD-derived precursor,due to its enhanced sensitivity,is recommended for early warning systems.These findings provide new insights into the role of LRs in rockburst dynamics and offer practical guidance for improving precursor identification and disaster mitigation strategies.
基金funding support from the National Natural Science Foundation of China(Grant Nos.52174092 and 51904290)the Natural Science Foundation of Jiangsu Province,China(Grant No.BK20220157).
文摘In rock engineering,the cyclic shear characteristics of rough joints under dynamic disturbances are still insufficiently studied.This study conducted cyclic shear experiments on rough joints under dynamic normal loads to assess the impact of shear frequency(f_(h))and shear displacement amplitude(u_(d))on the frictional properties of the joint.The results reveal that within a single shearing cycle,the normal displacement negatively correlates with the dynamic normal force.As the shear cycle number increases,the joint surface undergoes progressive wear,resulting in an exponential decrease in the peak normal displacement.In the cyclic shearing procedure,the forward peak values of shear force and friction coefficient display larger fluctuations at either lower or higher shear frequencies.However,under moderate shear frequency conditions,the changes in the shear strength of the joint surface are smaller,and the degree of degradation post-shearing is relatively limited.As the shear displacement amplitude increases,the range of normal deformation within the joint widens.Furthermore,after shearing,the corresponding joint roughness coefficient trend shows a gradual decrease with an increasing shear displacement amplitude,while varying with the shearing frequency in a pattern that initially rises and then falls,with a turning point at 0.05 Hz.The findings of this research contribute to a profound comprehension of the cyclic frictional properties of rock joints under dynamic disturbances.
基金supported by the National Natural Science Foundation of China (No. 51404278)the State Key Program of National Natural Science Foundation of China (No. 51134005)
文摘With the third innovation in science and technology worldwide, China has also experienced thismarvelous progress. Concerning the longwall mining in China, the ＂masonry beam theory＂ （MBT） wasfirst proposed in the 1960s, illustrating that the transmission and equilibrium method of overburdenpressure using reserved coal pillar in mined-out areas can be realized. This forms the so-called ＂121mining method＂, which lays a solid foundation for development of mining science and technology inChina. The ＂transfer rock beam theory＂ （TRBT） proposed in the 1980s gives a further understanding forthe transmission path of stope overburden pressure and pressure distribution in high-stress areas. In thisregard, the advanced 121 mining method was proposed with smaller coal pillar for excavation design,making significant contributions to improvement of the coal recovery rate in that era. In the 21st century,the traditional mining technologies faced great challenges and, under the theoretical developmentspioneered by Profs. Minggao Qian and Zhenqi Song, the ＂cutting cantilever beam theory＂ （CCBT） wasproposed in 2008. After that the 110 mining method is formulated subsequently, namely one stope face,after the first mining cycle, needs one advanced gateway excavation, while the other one is automaticallyformed during the last mining cycle without coal pillars left in the mining area. This method can beimplemented using the CCBT by incorporating the key technologies, including the directional presplittingroof cutting, constant resistance and large deformation （CRLD） bolt/anchor supporting systemwith negative Poisson＇s ratio （NPR） effect material, and remote real-time monitoring technology. TheCCBT and 110 mining method will provide the theoretical and technical basis for the development ofmining industry in China.
基金supported by the National Natural Science Foundation of China(Grant No.41941018)Key Technology Research on Water Diversion Project for Central Area of Yunnan Province,China.All the supports are gratefully acknowledged.
文摘Rockburst is becoming a huge challenge for the utilization of deep underground space.Extensive efforts have been devoted to investigating the rockburst behavior and mechanism experimentally,theoretically,and numerically.The aim of this review is to discuss the novel development and the state-of-the-art in experimental techniques,theories,and numerical approaches proposed for rockburst.The definition and classification of rockburst are first summarized with an in-depth comparison among them.Then,the available laboratory experimental technologies for rockburst are reviewed in terms of indirect and direct approaches,with the highlight of monitoring technologies and data analysis methods.Some key rockburst influencing factors(i.e.size and shape,rock types,stress state,water content,and temperature)are analyzed and discussed based on collected data.After that,rockburst theories and mechanisms are discussed and evaluated,as well as the microscopic observation.The simulation approaches of rockburst are also summarized with the highlight of optional novel numerical methods.The accuracy,stability,and reliability of different experimental,theoretical and numerical approaches are also compared and assessed in each part.Finally,a summary and some aspects of prospective research are presented.
基金This study has been funded by the National Natural Science Foundation of China(Grant No.41941018)and the Second Tibetan Plateau Scientific Expedition and Research Grant(Grant No.2019QZKK0708).
文摘Quasi-NPR(negative Poisson’s ratio)steel is a new type of super bolt material with high strength,high ductility,and a micro-negative Poisson’s effect.This material overcomes the contrasting characteristics of the high strength and high ductility of steel and it has significant energy-absorbing characteristics,which is of high value in deep rock and soil support engineering.However,research on the shear resistance of quasi-NPR steel has not been carried out.To study the shear performance of quasi-NPR steel bolted rock joints,indoor shear tests of bolted rock joints under different normal stress conditions were carried out.Q235 steel and#45 steel,two representative ordinary bolt steels,were set up as a control group for comparative tests to compare and analyze the shear strength,deformation and instability mode,shear energy absorption characteristics,and bolting contribution of different types of bolts.The results show that the jointed rock masses without bolt reinforcement undergo brittle failure under shear load,while the bolted jointed rock masses show obvious ductile failure characteristics.The shear deformation ca-pacity of quasi-NPR steel is more than 3.5 times that of Q235 steel and#45 steel.No fracture occurs in the quasi-NPR steel during large shear deformation and it can provide stable shear resistance.However,the other two types of control bolts become fractured under the same conditions.Quasi-NPR steel has significant energy-absorbing characteristics under shear load and has obvious advantages in terms of absorbing the energy released by shear deformation of jointed rock masses as compared with ordinary steel.In particular,the shear force plays a major role in resisting the shear deformation of Q235 steel and#45 steel,therefore,fracture failure occurs under small bolt deformation.However,the axial force of quasi-NPR steel can be fully exerted when resisting joint shear deformation;the steel itself does not break when large shear deformation occurs,and the supporting effect of the jointed rock mass is effectively guaranteed.
基金support by the Key Program of National Natural Science Foundation of China(51134005)Doctoral Scientific Fund Project of the Ministry of Education of China(20120023120004)is gratefully acknowledged.
文摘With the increasing exploitation scope and intensity,the shallow resources would be exhausted in the future;and the deep mining will become an essential choice.In deep tunnel engineering,the heat-harm becomes one of the mainbariers.Investigations on high temperature coal mine have been done in Nothem China,with the construting of threemodels of high temperature mines suffering heat-harm,at the Jiahe mine,Sanhejian mine and Zhangshuanglou mine.Thedomestic and abroad cooling technologies of the mine respectively are also summarized after comparatively analyzing theadvantages and disadvantages of each technology.Finally,we find that the high temperature exchange machinery system(HEMS)technology that use mine discharge as the cold source,is excellent to heat-ham control in deep mines.Taking theJiahe coal mine as an example,we systematically introduce this teclnology by disposing three main workstations.HEMStechnology with its operations and functions in different exploitation levels are accomplished,including the extraction ofrefrigerating output,the transportation of chilled water by closed circulation line,the decompression of circulation linesand equipment by pressure transformation machine,and the heat exchange and cooling of workplace by heat exchangebetween wind stream and the chilled water.The exchanged heat source from the workplace is taken to ground heating bythe circulating water which acts as a carrier.It shows that the HEMS-technology benefit in environment protection andemission reduction.Results of this project illustrate that it is efficient in heat-ham control with the temperature decrease ofthe workplace down to 26-29℃,and being 4-6℃ lower than the original,and the relative humidity 5%-15%lowerthan before.It greatly improves the working environment of underground workplace suffering heat-ham of high tem-perature and high humidity.In addition,by the extracting of deep geothermal enery,ground fired boiler for heating hasbeen replaced,reducing environmental pollution.This technology is worth generalization in deep mines and related fields.
文摘The 2008 Wenchuan earthquake resulted in a large number of fatalities and caused significant economic losses.Thousands of landslides,many of which are very large,were triggered by the earthquake.A majority of catastrophic landslides were distributed along the central Longmenshan fault system,at the eastern margin of the Tibetan Plateau.Some of the landslides resulted in sudden damming of rivers causing flooding,which in turn induced secondary sliding disasters.Among the most significant landslides,the Daguangbao landslide was the largest in volume with the maximum thickness.For this,a numerical model of the Daguangbao landslide,using the material point method(MPM),was developed to simulate the interaction of the seismic loads imposed on the slope.The numerical results then are compared with the post-earthquake profile.As a consequence of the landslide,a nearly vertical head scarp with a maximum height of about 700 m was generated.This is considered as a high risk situation that requires constant monitoring and evaluation.Finally,we propose a methodology based on Bayesian networks(BNs)to manage the risk associated with the stability of the rockwall at the Daguangbao landslide site.
基金supported by the National Natural Science Foundation of China(NSFC)(41941018).
文摘2G-NPR bolt (the 2nd generation Negative Poisson’s Ratio bolt) is a new type of bolt with high strength, high toughness and no yield platform. It has signifcant efects on improving the shear strength of jointed rock mass and controlling the stability of surrounding rock. To achieve an accurate simulation of bolted joint shear tests, we have studied a numerical simulation method that takes into account the 2G-NPR bolt's tensile–shear fracture criterion. Firstly, the indoor experimental study on the tensile–shear mechanical properties of 2G-NPR bolt is carried out to explore its mechanical properties under diferent tensile–shear angles, and the fracture criterion of 2G-NPR bolt considering the tensile–shear angle is established. Then, a three-dimensional numerical simulation method considering the tensile–shear mechanical constitutive and fracture criterion of 2G-NPR bolt, the elastoplastic mechanical behavior of surrounding rock and the damage and deterioration of grouting body is proposed. The feasibility and accuracy of the method are verifed by comparing with the indoor shear test results of 2G-NPR bolt anchorage joints. Finally, based on the numerical simulation results, the deformation and stress of the bolt, the distribution of the plastic zone of the rock mass, the stress distribution and the damage of the grouting body are analyzed in detail. The research results can provide a good reference value for the practical engineering application and shear mechanical performance analysis of 2G-NPR bolt.
基金the Postgraduate Research&Practice Innovation Program of Jiangsu Province,China(Grant No.KYCX21_2368)。
文摘The use of explosives is restricted on some important holidays,and the handling of unexploded charge is very dangerous.Therefore,an innovative non-explosive technology called instantaneous expansion(IE)was developed for tunneling.IE,whose components are derived from solid wastes such as coal gangue and straw conduces to realizing the reuse of waste.Moreover,its cost is lower than explosives.Blind guns of IE are easy to treat with water.The IE tunneling method is classified into two categories,i.e.IE with a single fracture(IESF)and IE with multiple fractures(IEMF),which are used to form the tunnel crosssection directionally cross-section and to fragment the rocks inside the cross-section,respectively.In this study,the principle of IE tunneling was elaborated first.Then,tunneling experiments and numerical simulations were performed on IE,conventional blasting(CB)and shaped charge blasting(SCB)in comparison.The experimental and numerical results show that IE achieved the best performance of directional rock breaking and corresponded to the most minor excavation-induced damage zone of the surrounding rock.Besides,the tunnel cross-section created by IE was flat and smooth.Comparing IE with CB and SCB,the over/under-excavation area decreased by 64%and 17%,and the excavation-induced damage zone fell by 26%and 11%,respectively.The range of the loose circle is reduced,which is conducive to improving the long-term stability of the roadway.The research provides a safe and economical tunneling method with excellent application prospects.
基金The financial support from the National Natural Science Foun-dation of China(Grant Nos.52074299 and 41941018)the Fundamental Research Funds for the Central Universities of China(Grant No.2023JCCXSB02)are gratefully acknowledged.
文摘To investigate the mechanism of rockburst prevention by spraying water onto the surrounding rocks,15 experiments are performed considering different water absorption levels on a single face.High-speed photography and acoustic emission(AE)system are used to monitor the rockburst process.The effect of water on sandstone rockburst and the prevention mechanism of water on sandstone rockburst are analyzed from the perspective of energy and failure mode.The results show that the higher the ab-sorption degree,the lower the intensity of the rockburst after absorbing water on single side of sand-stone.This is reflected in the fact that with the increase in the water absorption level,the ejection velocity of rockburst fragments is smaller,the depth of the rockburst pit is shallower,and the AE energy is smaller.Under the water absorption level of 100%,the magnitude of rockburst intensity changes from medium to slight.The prevention mechanism of water on sandstone rockburst is that water reduces the capacity of sandstone to store strain energy and accelerates the expansion of shear cracks,which is not conducive to the occurrence of plate cracking before rockburst,and destroys the conditions for rockburst incubation.
基金National Natural Science Foundation of China,Grant/Award Number:41941018State Key Laboratory for GeoMechanics and Deep Underground Engineering,Grant/Award Number:SKLGDUEK202201。
文摘Given the challenges in managing large deformation disasters in energy engineering,traffic tunnel engineering,and slope engineering,the excavation compensation theory has been proposed for large deformation disasters and the supplementary technology system is developed accordingly.This theory is based on the concept that“all destructive behaviors in tunnel engineering originate from excavation.”This paper summarizes the development of the excavation compensation theory in five aspects:the“theory,”“equipment,”“technology,”the design method with large deformation mechanics,and engineering applications.First,the calculation method for compensation force has been developed based on this theory,and a comprehensive large deformation disaster control theory system is formed.Second,a negative Poisson's ratio anchor cable with high preload,large deformation,and super energy absorption characteristics has been independently developed and applied to large deformation disaster control.An intelligent tunnel monitoring and early warning cloud platform system are established for remote monitoring and early warning system of Newton force in landslide geological hazards.Third,the double gradient advance grouting technology,the two-dimensional blasting technology,and the integrated Newton force monitoring--early warning--control technology are developed for different engineering environments.Finally,some applications of this theory in China's energy,traffic tunnels,landslide,and other field projects have been analyzed,which successfully demonstrates the capability of this theory in large deformation disaster control.
文摘The most common method used to describe earthquake activity is based on the changes in physical parameters of the earth's surface such as displacement of active fault and seismic wave.However,such approach is not successful in forecasting the movement behaviors of faults.In the present study,a new mechanical model of fault activity,considering the shear strength on the fault plane and the influence of the resistance force,is established based on the occurrence condition of earthquake.A remote real-time monitoring system is correspondingly developed to obtain the changes in mechanical components within fault.Taking into consideration the local geological conditions and the history of fault activity in Zhangjiakou of China,an active fault exposed in the region of Zhangjiakou is selected to be directly monitored by the real-time monitoring technique.A thorough investigation on local fault structures results in the selection of two suitable sites for monitoring potential active tectonic movements of Zhangjiakou fault.Two monitoring curves of shear strength,recorded during a monitoring period of 6 months,turn out to be steady,which indicates that the potential seismic activities hardly occur in the adjacent region in the near future.This monitoring technique can be used for early-warning prediction of the movement of active fault,and can help to further gain an insight into the interaction between fault activity and relevant mechanisms.
基金financial support from the National Natural Science Foundation of China(Nos.52174092,51904290,52004272,52104125,42372328,and U23B2091)Natural Science Foundation of Jiangsu Province,China(Nos.BK20220157 and BK20240209)+3 种基金the Fundamental Research Funds for the Central Universities,China(No.2022YCPY0202)Xuzhou Science and Technology Project,China(Nos.KC21033 and KC22005)Yunlong Lake Laboratory of Deep Underground Science and Engineering Project,China(No.104023002)the Graduate Innovation Program of China University of Mining and Technology(No.2023WLTCRCZL052)。
文摘This study aims to investigate mechanical properties and failure mechanisms of layered rock with rough joint surfaces under direct shear loading.Cubic layered samples with dimensions of 100 mm×100 mm×100 mm were casted using rock-like materials,with anisotropic angle(α)and joint roughness coefficient(JRC)ranging from 15°to 75°and 2-20,respectively.The direct shear tests were conducted under the application of initial normal stress(σ_(n)) ranging from 1-4 MPa.The test results indicate significant differences in mechanical properties,acoustic emission(AE)responses,maximum principal strain fields,and ultimate failure modes of layered samples under different test conditions.The peak stress increases with the increasingαand achieves a maximum value atα=60°or 75°.As σ_(n) increases,the peak stress shows an increasing trend,with correlation coefficients R² ranging from 0.918 to 0.995 for the linear least squares fitting.As JRC increases from 2-4 to 18-20,the cohesion increases by 86.32%whenα=15°,while the cohesion decreases by 27.93%whenα=75°.The differences in roughness characteristics of shear failure surface induced byαresult in anisotropic post-peak AE responses,which is characterized by active AE signals whenαis small and quiet AE signals for a largeα.For a given JRC=6-8 andσ_(n)=1 MPa,asαincreases,the accumulative AE counts increase by 224.31%(αincreased from 15°to 60°),and then decrease by 14.68%(αincreased from 60°to 75°).The shear failure surface is formed along the weak interlayer whenα=15°and penetrates the layered matrix whenα=60°.Whenα=15°,as σ_(n) increases,the adjacent weak interlayer induces a change in the direction of tensile cracks propagation,resulting in a stepped pattern of cracks distribution.The increase in JRC intensifies roughness characteristics of shear failure surface for a smallα,however,it is not pronounced for a largeα.The findings will contribute to a better understanding of the mechanical responses and failure mechanisms of the layered rocks subjected to shear loads.
基金supported by the National Natural Science Foundation of China (41941018)supported by Beijing Natural Science Foundation (8212033)+1 种基金supported by the Fundamental Research Funds for the Central Universities (2021YJSLI13,2021JCCXLJ05)supported by Innovation Fund Research Project (SKLGDUEK202221).
文摘High geo-temperature is one of the inevitable geological disasters in deep engineering such as resource extraction,space development,and energy utilization.One of the key issues is to understand the mechanical properties and failure mechanism of high-temperature rock disturbed by low-temperature airflow after excavation.Therefore,.the experimental and numerical investigation were carried out to study the impact of cooling rate on mechanical properties and failure mechanism of high temperature sandstone.First,uniaxial compression experiments of high temperature sandstone at different real-time cooling rates were carried out to study the mechanical properties and failure modes.The experimental results indicate that the cooling rate has a significant effect on the mechanical properties and failure modes of sandstone.The peak strain,peak stress,and elastic modulus decrease with an increase in cooling rate,and the fragmentation degree after failure increases gradually.Moreover,the equivalent numerical model of heterogeneous sandstone was established using particle flow code(PFC)to reveal the failure mechanism.The results indicate that the sandstone is dominated by intragrain failure in the cooling stage,the number of microcracks is exponentially related to the cooling rate,and the higher the cooling rate,the more cracks are concentrated in the exterior region.Under axial loading,the tensile stress is mostly distributed along the radial direction,and the damage in the cooling stage is mostly due to the fracture of the radial bond.In addition,axial loading,temperature gradient and thermal stress mismatch between adjacent minerals are the main reasons for the damage of sandstone in the cooling stage.Moreover,the excessive temperature gradient in the exterior region of the sandstone is the main reason for the damage concentration in this region.
基金supported by the General Program of the National Natural Science Foundation of China(Grant No.52074295)the Special Fund for Basic Scientific Research Business Expenses of Central Universities(Grant No.2022YJSSB06)supported by State Key Laboratory for Geomechanics and Deep Underground Engineering,China University of Mining and technology,Beijing,China(Grant No.SKLGDUEK202217).
文摘A nuclear explosion in the rock mass medium can produce strong shock waves,seismic shocks,and other destructive effects,which can cause extreme damage to the underground protection infrastructures.With the increase in nuclear explosion power,underground protection engineering enabled by explosion-proof impact theory and technology ushered in a new challenge.This paper proposes to simulate nuclear explosion tests with on-site chemical explosion tests in the form of multi-hole explosions.First,the mechanism of using multi-hole simultaneous blasting to simulate a nuclear explosion to generate approximate plane waves was analyzed.The plane pressure curve at the vault of the underground protective tunnel under the action of the multi-hole simultaneous blasting was then obtained using the impact test in the rock mass at the site.According to the peak pressure at the vault plane,it was divided into three regions:the stress superposition region,the superposition region after surface reflection,and the approximate plane stress wave zone.A numerical simulation approach was developed using PFC and FLAC to study the peak particle velocity in the surrounding rock of the underground protective cave under the action of multi-hole blasting.The time-history curves of pressure and peak pressure partition obtained by the on-site multi-hole simultaneous blasting test and numerical simulation were compared and analyzed,to verify the correctness and rationality of the formation of an approximate plane wave in the simulated nuclear explosion.This comparison and analysis also provided a theoretical foundation and some research ideas for the ensuing study on the impact of a nuclear explosion.
基金The financial support from the National Natural Science Foundation of China(Grant Nos.41941018 and 52074299)the Fundamental Research Funds for the Central Universities of China(Grant No.2023JCCXSB02)。
文摘Rockburst are often encountered in tunnel construction due to the complex geological conditions.To study the influence of unloading rate on rockburst,gneiss rockburst experiments were conducted under three groups of unloading rates.A high-speed photography system and acoustic emission(AE)system were used to monitor the entire process of rockburst process in real-time.The results show that the intensity of gneiss rockburst decreases with decrease of unloading rate,which is manifested as the reduction of AE energy and fragments ejection velocity.The mechanisms are proposed to explain this effect:(i)The reduction of unloading rate changes the crack propagation mechanism in the process of rockburst.This makes the rockbursts change from the tensile failure mechanism at high unloading rate to the tension-shear mixed failure mechanism at low unloading rate,and more energy released in the form of shear crack propagation.Then,less strain energy is converted into kinetic energy of fragments ejection.(ii)Less plate cracking degree of gneiss has taken shape due to decrease of unloading rate,resulting in the destruction of rockburst incubation process.The enlightenments of reducing the unloading rate for the project are also described quantitatively.The rockburst magnitude is reduced from the medium magnitude at the unloading rate of 0.1 MPa/s to the slight magnitude at the unloading rate of 0.025 MPa/s,which was judged by the ejection velocity.
基金supported by grants from the Research Grant Council of the Hong Kong Special Administrative Region,China(Project Nos.HKU 7137/03E and R7005/01E)。
文摘Rock and geotechnical engineering investigations involve drilling holes in ground with or without retrieving soil and rock samples to construct the subsurface ground profile.On the basis of an actual soil nailing drilling for a slope stability project in Hong Kong,this paper further develops the drilling process monitoring(DPM)method for digitally profiling the subsurface geomaterials of weathered granitic rocks using a compressed airflow driven percussive-rotary drilling machine with down-the-hole(DTH)hammer.Seven transducers are installed on the drilling machine and record the chuck displacement,DTH rotational speed,and five pressures from five compressed airflows in real-time series.The mechanism and operations of the drilling machine are elaborated in detail,which is essential for understanding and evaluating the drilling data.A MATLAB program is developed to automatically filter the recorded drilling data in time series and classify them into different drilling processes in sub-time series.These processes include penetration,push-in with or without rod,pull-back with or without rod,rod-tightening and rod-untightening.The drilling data are further reconstructed to plot the curve of drill-bit depth versus the net drilling time along each of the six drillholes.Each curve is found to contain multiple linear segments with a constant penetration rate,which implies a zone of homogenous geomaterial with different weathering grades.The effect from fluctuation of the applied pressures is evaluated quantitatively.Detailed analyses are presented for accurately assess and verify the underground profiling and strength in weathered granitic rock,which provided the basis of using DPM method to confidently assess drilling measurements to interpret the subsurface profile in real time.
