The Mg-6Al-4Zn alloy was fabricated by mechanical alloying(MA)and hot pressing to serve as biodegradable metal implant.The influence of addition of 1%Si(mass fraction)on the microstructure,mechanical properties and bi...The Mg-6Al-4Zn alloy was fabricated by mechanical alloying(MA)and hot pressing to serve as biodegradable metal implant.The influence of addition of 1%Si(mass fraction)on the microstructure,mechanical properties and bio-corrosion behavior of Mg-6Al-1Zn alloy was studied using X-ray diffractometry,transmission electron microscopy,compression test,as well as immersion,electrochemical test and MTT assay.The results showed that the addition of 1%Si to Mg-6Al-1Zn alloy led to the formation of fine Mg2Si phase with polygonal shape,and increased compressive strength,elongation and improved corrosion resistance.Furthermore,the cell viability of Saos-2 cells has been improved by addition of 1%Si to Mg-6Al-1Zn alloy.According to the results,the magnesium ions released in the methylthiazol tetrazolium(MTT)test have not shown any cell toxicity.All these indicated that the addition of 1%Si improved the properties of Mg-6Al-4Zn alloy for using as a biodegradable implant.展开更多
Al-20Si-5Fe melt was rapidly solidified into particles and ribbons and then consolidated to near full density by hot pressing at 400℃/250 MPa/1 h. According to the eutectic-growth and dendritic-growth velocity models...Al-20Si-5Fe melt was rapidly solidified into particles and ribbons and then consolidated to near full density by hot pressing at 400℃/250 MPa/1 h. According to the eutectic-growth and dendritic-growth velocity models, the solidification front velocity and the amount of undercooling were estimated for the particles with different sizes. Values of 0.43-1.2 cm/s and 15-28 K were obtained. The secondary dendrite arm spacing revealed a cooling rate of 6 × 10^5 K/s for the particles with an average size of 20 μm. Solidification models for the ribbons yielded a cooling rate of 5 × 10^7 K/s. As a result of the higher cooling rate, the melt-spun ribbons exhibited considerable microstructural refinement and modification. The size of the primary silicon decreased from approximately 1μm to 30 nm while the formation of iron-containing intermetallic compounds was suppressed. Supersaturation of the aluminum matrix in an amount of-7 at.% Si was noticed from the XRD patterns During the hot consolidation process, coarsening of the primary silicon particles and precipitation of β-Al5FeSi phase were observed. Evaluation of the compressive strength and hardness of the alloy indicated an improvement in mechanical properties due to the microstructural modification.展开更多
Thethermal stability and the kinetics of grain growth of nanocrystalline Mg-6Al-1Zn and Mg-6Al-1Zn-1Si alloys prepared via mechanical alloying were investigated. It started with elemental powders, using a variety of a...Thethermal stability and the kinetics of grain growth of nanocrystalline Mg-6Al-1Zn and Mg-6Al-1Zn-1Si alloys prepared via mechanical alloying were investigated. It started with elemental powders, using a variety of analytical techniques including differential scanning calorimetry （DSC）, X-ray diffraction （XRD）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and energy dispersive spectrometry. The kinetics of grain growth in isothermal annealing was investigated. The XRD results show that, although the grain sizes of both material systems increase as the annealing temperature rises, the Si-containing system displays a relatively smaller grain size, i.e., 60 nm compared with 72 nm in Mg-6Al-1Zn system, after being exposed to 350 ℃ for 1 h. The second-phase intermetallic particle Mg2Si formed during the isothermal annealing of Mg-6Al-1Zn-1Si system could influence not only the activation energy but also the exponent of kinetic equation. Higher hardness values obtained in the Si-containing system would be due to the formation of Mg2Si intermetallic phase.展开更多
文摘The Mg-6Al-4Zn alloy was fabricated by mechanical alloying(MA)and hot pressing to serve as biodegradable metal implant.The influence of addition of 1%Si(mass fraction)on the microstructure,mechanical properties and bio-corrosion behavior of Mg-6Al-1Zn alloy was studied using X-ray diffractometry,transmission electron microscopy,compression test,as well as immersion,electrochemical test and MTT assay.The results showed that the addition of 1%Si to Mg-6Al-1Zn alloy led to the formation of fine Mg2Si phase with polygonal shape,and increased compressive strength,elongation and improved corrosion resistance.Furthermore,the cell viability of Saos-2 cells has been improved by addition of 1%Si to Mg-6Al-1Zn alloy.According to the results,the magnesium ions released in the methylthiazol tetrazolium(MTT)test have not shown any cell toxicity.All these indicated that the addition of 1%Si improved the properties of Mg-6Al-4Zn alloy for using as a biodegradable implant.
基金The authors wish to sincerely acknowledge the High Technology Industries Center, Iranian Ministry of Mines and Metals for financial support of the research work.
文摘Al-20Si-5Fe melt was rapidly solidified into particles and ribbons and then consolidated to near full density by hot pressing at 400℃/250 MPa/1 h. According to the eutectic-growth and dendritic-growth velocity models, the solidification front velocity and the amount of undercooling were estimated for the particles with different sizes. Values of 0.43-1.2 cm/s and 15-28 K were obtained. The secondary dendrite arm spacing revealed a cooling rate of 6 × 10^5 K/s for the particles with an average size of 20 μm. Solidification models for the ribbons yielded a cooling rate of 5 × 10^7 K/s. As a result of the higher cooling rate, the melt-spun ribbons exhibited considerable microstructural refinement and modification. The size of the primary silicon decreased from approximately 1μm to 30 nm while the formation of iron-containing intermetallic compounds was suppressed. Supersaturation of the aluminum matrix in an amount of-7 at.% Si was noticed from the XRD patterns During the hot consolidation process, coarsening of the primary silicon particles and precipitation of β-Al5FeSi phase were observed. Evaluation of the compressive strength and hardness of the alloy indicated an improvement in mechanical properties due to the microstructural modification.
文摘Thethermal stability and the kinetics of grain growth of nanocrystalline Mg-6Al-1Zn and Mg-6Al-1Zn-1Si alloys prepared via mechanical alloying were investigated. It started with elemental powders, using a variety of analytical techniques including differential scanning calorimetry （DSC）, X-ray diffraction （XRD）, scanning electron microscopy （SEM）, transmission electron microscopy （TEM） and energy dispersive spectrometry. The kinetics of grain growth in isothermal annealing was investigated. The XRD results show that, although the grain sizes of both material systems increase as the annealing temperature rises, the Si-containing system displays a relatively smaller grain size, i.e., 60 nm compared with 72 nm in Mg-6Al-1Zn system, after being exposed to 350 ℃ for 1 h. The second-phase intermetallic particle Mg2Si formed during the isothermal annealing of Mg-6Al-1Zn-1Si system could influence not only the activation energy but also the exponent of kinetic equation. Higher hardness values obtained in the Si-containing system would be due to the formation of Mg2Si intermetallic phase.
