The dissimilar joining of biodegradable magnesium alloy to pure commercial titanium by rotational friction welding with rotational speeds of 1100,1200 and 1300 r/min for the production of bio-screw was investigated.Th...The dissimilar joining of biodegradable magnesium alloy to pure commercial titanium by rotational friction welding with rotational speeds of 1100,1200 and 1300 r/min for the production of bio-screw was investigated.The metallographic analysis revealed that a good joining was obtained at the Ti/Mg alloy joint.On the magnesium alloy side,various regions such as the weld center zone(WCZ),dynamic recrystallization zone(DRX),thermo-mechanically affected zone(TMAZ)and partially deformed zone(PDZ)were observed.The highest tensile and shear strengths were 173 and 103.2 MPa,respectively at a rotational speed of 1300 r/min.The Ti/Mg alloy dissimilar friction welded joint failed at the vicinity of the intermetallic zone containing Ti3Al phase.The hardness values from the base metal magnesium alloy to the joining point increased mainly due to grain refinement(8.57μm in diameter)and the presence of titanium particles,while the hardness values were constant on the titanium side.It was also found that the corrosion rate of the Ti/Mg alloy joint was higher compared with that of the Ti and Mg alloy from the immersion studies.Additionally,the sample with a rotational speed of 1300 r/min showed better biocompatibility and a cell viability of 98.12%due to better corrosion resistance.展开更多
The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions...The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions increased impact toughness, ultimate tensile strength, and elongation of the alloy as a result of change in eutectic Si morphology. The analysis of fracture surfaces revealed that with addition of Sr and to lesser extent Bi and Sb, the alloy exhibited a predominantly ductile fracture rather than quasi-cleavage brittle fracture. Moreover, with the additions of Sr, Bi and Sb, the quality index increased to 164.7 MPa, 156.3 MPa and 152.6 MPa respectively from 102 MPa for the base alloy. Polarization corrosion tests conducted in sodium chloride solution showed that the corrosion potential shifted to more negative values with additions of Sb, Bi and Sr, respectively. Corrosion immersion tests also revealed that the element additions have a detrimental effect on the corrosion rate of alloys, due to the increase of boundaries between the Al and eutectic Si phases.展开更多
Plasma electrolytic oxidation（PEO） was developed as a bond coat for air plasma sprayed（APS） nanostructure ZrO2 as top coat to enhance the corrosion resistance and antibacterial activity of Mg alloy. Corrosion beha...Plasma electrolytic oxidation（PEO） was developed as a bond coat for air plasma sprayed（APS） nanostructure ZrO2 as top coat to enhance the corrosion resistance and antibacterial activity of Mg alloy. Corrosion behavior and antibacterial activities of coated and uncoated samples were assessed by electrochemical tests and agar diffusion method toward Escherichia coli（E. coli） bacterial pathogens, respectively. The lowest corrosion current density and the highest charge transfer resistance, phase angle and impedance modulus were observed for PEO/nano-ZrO2 coated sample compared with those of PEO coated and bare Mg alloys. Nano-ZrO2 top coat which has completely sealed PEO bond coat is able to considerably delay aggressive ions transportation towards Mg alloy surface and significantly enhances corrosion resistance of Mg alloy in simulated body fluid（SBF） solution. Moreover, higher antibacterial activity was also observed in PEO/nano-ZrO2 coating against bacterial strains than that of the PEO coated and bare Mg alloys. This observation was attributed to the presence of ZrO2 nanoparticles which decelerate E. coli growth as a result of E. coli membranes.展开更多
Bi-layered thermally grown oxide （TGO） layer plays a major role in the spallation of Y2O3 stabilized ZrO2 （YSZ） layer form the bond coat in the thermal barrier coating （TBC） systems during oxidation. On the othe...Bi-layered thermally grown oxide （TGO） layer plays a major role in the spallation of Y2O3 stabilized ZrO2 （YSZ） layer form the bond coat in the thermal barrier coating （TBC） systems during oxidation. On the other hand, bi-layered TGO formation and growth in the TBC systems with nanostructured YSZ have not been deeply investigated during cyclic oxidation. Hence, Inconel 738/NiCrAlY/normal YSZ and Inconel 738/NiCrAlY/nano YSZ systems were pre-oxidized at 1000 °C and then subjected to cyclic oxidation at 1150 °C. According to microstructural observations, nanostructured YSZ layer over the bond coat should have less mi-cro-cracks and pinholes, due to the compactness of the nanostructure and the presence of nano zones that resulted in lower O infiltration into the nanothermal barrier coating system, formation of thinner and nearly continuous mono-layered thermally grown oxide on the bond coat during pre-oxidation, lower spinels formation at the Al2O3/YSZ interface and finally, reduction of bi-layered thermally grown oxide thickness during cyclic oxidation. It was found that pre-heat treatment and particularly coating microstructure could influence microstructural evolution （bi-layered TGO thickness） and durability of thermal barrier coating systems during cyclic oxidation.展开更多
Infection is a major potential complication in the clinical treatment of bone injuries. Magnesium (Mg)-based composites are biodegradable and antibacterial biomaterials that have been employed to reduce infection foll...Infection is a major potential complication in the clinical treatment of bone injuries. Magnesium (Mg)-based composites are biodegradable and antibacterial biomaterials that have been employed to reduce infection following surgical implants. The aim of present study was to synthesize and in-vitro characterize Mg-based scaffolds containing silver for bone tissue engineering. Porous Mg-based scaffolds with four silver concentrations (i.e., 0, 0.5 wt.%, 1 wt.%, and 2 wt.%), denoted by Mg?Ca?Mn-Zn-xAg (MCMZ?xAg)(where x is the silver concentration), were fabricated by the space holder technique. The effects of silver concentration on pore architecture, mechanical properties, bioactivity, and zone of bacterial inhibition were investigated in-vitro. X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and fluorescence microscopy were utilized to characterize the obtained scaffolds. In-vitro corrosion test results indicated that the MCMZ scaffolds with lower silver content were more resistant to corrosion than those enriched with higher amounts of silver. Examination of the antibacterial activity showed that the MCMZ?Ag scaffolds exhibited superb potential with respect to suppressing the growth of Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus), in the inhibition zone around the MCMZ?Ag scaffolds, with increasing in the amount of incorporated silver;however, higher amounts of silver increased the cytotoxicity. Taken together, the results of this study demonstrate that the porous 0.5 wt.% Ag-containing scaffolds with interconnected pores, adequate mechanical properties, antibacterial activity, and cell adhesion are promising with respect to the repair and substitution of damaged and diseased bones.展开更多
Potential engineering applications of magnesium(Mg)and Mg-based alloys,as the lightest structural metal,have made them a popular subject of study.However,the inferior corrosion and wear characteristics significantly l...Potential engineering applications of magnesium(Mg)and Mg-based alloys,as the lightest structural metal,have made them a popular subject of study.However,the inferior corrosion and wear characteristics significantly limit their application range.It is widely recognized that surface treatment is the most commonly utilized technique for remarkably improving a substrate’s surface characteristics.Numerous methods have been introduced for the surface treatment of Mg and Mg-based alloys to improve their corrosion behavior and tribological performance.Among these,thermal spray(TS)technology provides several methods for deposition of various functional metallic,ceramic,cermet,or other coatings tailored to particular conditions.Recent researches have shown the tremendous potential for thermal spray coated Mg alloys for biomedical and industrial applications.In this context,the cold spray(CS)method,as a comparatively new TS coating technique,can generate the coating layer using kinetic energy rather than combined thermal and kinetic energies,like the high-velocity oxy-fuel(HVOF)spray method.Moreover,the CS process,as a revolutionary method,is able to repair and refurbish with a faster turnaround time;it also provides solutions that do not require dealing with the thermal stresses that are part of the other repair processes,such as welding or other TS processes using a high-temperature flame.In this review paper,the recently designed coatings that are specifically applied to Mg alloys(primarily for industrial applications)employing various coating processes are reviewed.Because of the increased utilization of CS technology for both 3D printed(additively manufactured)coatings and repair of structurally critical components,the most recent CS methods for the surface treatment,repair,and refurbishment of Mg alloys as well as their benefits and restrictions are then discussed and reviewed in detail.Lastly,the prospects of this field of study are briefly discussed,along with a summary of the presented work.展开更多
Magnesium(Mg)-based materials are a new generation of alloys with the exclusive ability to be biodegradable within the human/animal body.In addition to biodegradability,their inherent biocompatibility and similar-to-b...Magnesium(Mg)-based materials are a new generation of alloys with the exclusive ability to be biodegradable within the human/animal body.In addition to biodegradability,their inherent biocompatibility and similar-to-bone density make Mg-based alloys good candidates for fabricating surgical bioimplants for use in orthopedic and traumatology treatments.To this end,nowadays additive manufacturing(AM)along with three-dimensional(3D)printing represents a promising manufacturing technique as it allows for the integration of bioimplant design and manufacturing processes specific to given applications.Meanwhile,this technique also faces many new challenges associated with the properties of Mg-based alloys,including high chemical reactivity,potential for combustion,and low vaporization temperature.In this review article,various AM processes to fabricate biomedical implants from Mg-based alloys,along with their metallic microstructure,mechanical properties,biodegradability,biocompatibility,and antibacterial properties,as well as various post-AM treatments were critically reviewed.Also,the challenges and issues involved in AM processes from the perspectives of bioimplant design,properties,and applications were identified;the possibilities and potential scope of the Mg-based scaffolds/implants are discussed and highlighted.展开更多
This study investigates the effect of graphene oxide(GO)on the mechanical and corrosion behavior,antibacterial performance,and cell response of Mg–Zn–Mn(MZM)nanocomposite.MZM/GO nanocomposites with different amounts...This study investigates the effect of graphene oxide(GO)on the mechanical and corrosion behavior,antibacterial performance,and cell response of Mg–Zn–Mn(MZM)nanocomposite.MZM/GO nanocomposites with different amounts of GO(i.e.,0.5 wt%,1.0 wt%,and1.5 wt%)were fabricated by the semi-powder metallurgy method.The influence of GO on the MZM nanocomposite was analyzed through the hardness,compressive,corrosion,antibacterial,and cytotoxicity tests.The experimental results showed that,with the increase in the amount of GO(0.5 wt%and 1.5 wt%),the hardness value,compressive strength,and antibacterial performance of the MZM nanocomposite increased,whereas the cell viability and osteogenesis level decreased after the addition of 1.5 wt%GO.Moreover,the electrochemical examination results showed that the corrosion behavior of the MZM alloy was significantly enhanced after encapsulation in 0.5 wt%GO.In summary,MZM nanocomposites reinforced with GO can be used for implant applications because of their antibacterial performance and mechanical property.展开更多
A type of polymer/ceramic coating was introduced on a magnesium-based nanocomposite, and the nanocomposite was evaluated for implant applications.The microstructure, corrosion, and bioactivity of the coated and uncoat...A type of polymer/ceramic coating was introduced on a magnesium-based nanocomposite, and the nanocomposite was evaluated for implant applications.The microstructure, corrosion, and bioactivity of the coated and uncoated samples were assessed.Mechanical alloying followed by sintering was applied to fabricate the Mg–3Zn–0.5Ag–15NiTi nanocomposite substrate.Moreover, different contents of poly(lactic-co-glycolic acid)(PLGA) coatings were studied, and 10 wt% of PLGA content was selected.The scanning electron microscopy(SEM) images of the bulk nanocomposite showed an acceptable homogenous dispersion of the Ni Ti nanoparticles(NPs) in the Mg-based matrix.In the in vitro bioactivity evaluation, following the immersion of the uncoated and coated samples in a simulated body fluid(SBF) solution, the Ca/P atomic ratio demonstrated that the apatite formation amount on the coated sample was greater than that on the uncoated nanocomposite.Furthermore, assessing the corrosion resistance indicated that the coatings on the Mg-based substrate led to a corrosion current density(icorr) that was considerably lower than that of the substrate.Such a condition revealed that the coating would provide an obstacle for the corrosion.Based on this study, the PLGA/hardystonite(HT) composite-coated Mg–3Zn–0.5Ag–15NiTi nanocomposite may be suitably applied as an orthopedic implant biomaterial.展开更多
The influence of hydrofluoric acid（HF） treatment on the corrosion behavior of the Mg-0.5Ca alloys was investigated by immersion specimen in sodium hydroxide and HF solutions with various concentrations and durations...The influence of hydrofluoric acid（HF） treatment on the corrosion behavior of the Mg-0.5Ca alloys was investigated by immersion specimen in sodium hydroxide and HF solutions with various concentrations and durations at room temperature.Microstructural evolutions of the specimens were characterized by atomic force microscopy,X-ray diffraction,field-emission scanning electron microscopy.The corrosion resistance was examined through potentiodynamic polarization and immersion test in Kokubo solution.The results revealed that the fluoride treated Mg-0.5Ca alloys produced by immersion in 40% HF provided more uniform,dense and thicker coating layer（12.6 μm） compared with the 35% HF treated specimen.The electrochemical test showed that the corrosion resistance of fluoride treated specimen was 35 times higher compared with the untreated Mg-0.5Ca alloy specimen in Kokubo solution.In vitro degradation rate of the fluoride treated specimens was much lower than untreated Mg-0.5Ca alloy in Kokubo solution.After immersion test the surface of 40% HF treated sample showed a few corrosion dots,while untreated specimens were fully covered by corrosion products and delamination.Fluoride treated Mg-0.5Ca alloy with 40% HF is a promising candidate as biodegradable implants due to its low degradation kinetics and good biocompatibility.展开更多
The effect of multi-step tempering on retained austenite content and mechanical properties of low alloy steel used in the forged cold back-up roll was investigated.Microstructural evolutions were characterized by opti...The effect of multi-step tempering on retained austenite content and mechanical properties of low alloy steel used in the forged cold back-up roll was investigated.Microstructural evolutions were characterized by optical microscope,X-ray diffraction,scanning electron microscope and Feritscope,while the mechanical properties were determined by hardness and tensile tests.The results revealed that the content of retained austenite decreased by about 2% after multi-step tempering.However,the content of retained austenite increased from 3.6% to 5.1% by increasing multi-step tempering temperature.The hardness and tensile strength increased as the austenitization temperature changed from 800 to 920 ℃,while above 920 ℃,hardness and tensile strength decreased.In addition,the maximum values of hardness,ultimate and yield strength were obtained via triple tempering at 520 ℃,while beyond 520 ℃,the hardness,ultimate and yield strength decreased sharply.展开更多
Magnesium(Mg)and its alloys are revolutionizing the field of interventional surgeries in the medical industry.Their high biocompatibility,biodegradability,and a similar elastic modulus to natural bone make porous Mg-b...Magnesium(Mg)and its alloys are revolutionizing the field of interventional surgeries in the medical industry.Their high biocompatibility,biodegradability,and a similar elastic modulus to natural bone make porous Mg-based structures potential candidates for orthopedic implants and tissue engineering scaffolding.However,fabricating and machining porous Mg-based structures is challenging due to their complexity and difficulties in achieving uniform or gradient porosity.This review aims to thoroughly explore various fabrication procedures used to create metallic scaffolds,with a specific focus on those made from Mg-based alloys.Both traditional manufacturing techniques,including the directional solidification of metal-gas eutectic technique,pattern casting,methods using space holders,and modern fabrication methods,which are based on additive manufacturing,are covered in this review article.Furthermore,the paper highlights the most important findings of recent studies on Mg-based scaffolds in terms of their microstructure specifications,mechanical properties,degradation and corrosion behavior,antibacterial activity,and biocompatibility(both in vivo and in vitro).While extensive research has been conducted to optimize manufacturing parameters and qualities of Mg-based scaffolds for use in biomedical applications,specifically for bone tissue engineering applications,further investigation is needed to fabricate these scaffolds with specific properties,such as high resistance to corrosion,good antibacterial properties,osteoconductivity,osteoinductivity,and the ability to elicit a favorable response from osteoblast-like cell lines.The review concludes with recommendations for future research in the field of medical applications.展开更多
文摘The dissimilar joining of biodegradable magnesium alloy to pure commercial titanium by rotational friction welding with rotational speeds of 1100,1200 and 1300 r/min for the production of bio-screw was investigated.The metallographic analysis revealed that a good joining was obtained at the Ti/Mg alloy joint.On the magnesium alloy side,various regions such as the weld center zone(WCZ),dynamic recrystallization zone(DRX),thermo-mechanically affected zone(TMAZ)and partially deformed zone(PDZ)were observed.The highest tensile and shear strengths were 173 and 103.2 MPa,respectively at a rotational speed of 1300 r/min.The Ti/Mg alloy dissimilar friction welded joint failed at the vicinity of the intermetallic zone containing Ti3Al phase.The hardness values from the base metal magnesium alloy to the joining point increased mainly due to grain refinement(8.57μm in diameter)and the presence of titanium particles,while the hardness values were constant on the titanium side.It was also found that the corrosion rate of the Ti/Mg alloy joint was higher compared with that of the Ti and Mg alloy from the immersion studies.Additionally,the sample with a rotational speed of 1300 r/min showed better biocompatibility and a cell viability of 98.12%due to better corrosion resistance.
文摘The microstructure evolution, mechanical and corrosion properties of Al-11Si-2Cu-0.8Zn die cast alloy treated with Bi, Sb and Sr additions were investigated. The results of mechanical testing showed that all additions increased impact toughness, ultimate tensile strength, and elongation of the alloy as a result of change in eutectic Si morphology. The analysis of fracture surfaces revealed that with addition of Sr and to lesser extent Bi and Sb, the alloy exhibited a predominantly ductile fracture rather than quasi-cleavage brittle fracture. Moreover, with the additions of Sr, Bi and Sb, the quality index increased to 164.7 MPa, 156.3 MPa and 152.6 MPa respectively from 102 MPa for the base alloy. Polarization corrosion tests conducted in sodium chloride solution showed that the corrosion potential shifted to more negative values with additions of Sb, Bi and Sr, respectively. Corrosion immersion tests also revealed that the element additions have a detrimental effect on the corrosion rate of alloys, due to the increase of boundaries between the Al and eutectic Si phases.
基金the Universiti Teknologi Malaysia (UTM) for providing research facilities and financial support under Grants No:(1)UTM-Research University Grant (RUG) (Q.J130000.2524.16H35),and (2)Nippon Sheet Glass (NSG) R.J130000.7324.4B300
文摘Plasma electrolytic oxidation（PEO） was developed as a bond coat for air plasma sprayed（APS） nanostructure ZrO2 as top coat to enhance the corrosion resistance and antibacterial activity of Mg alloy. Corrosion behavior and antibacterial activities of coated and uncoated samples were assessed by electrochemical tests and agar diffusion method toward Escherichia coli（E. coli） bacterial pathogens, respectively. The lowest corrosion current density and the highest charge transfer resistance, phase angle and impedance modulus were observed for PEO/nano-ZrO2 coated sample compared with those of PEO coated and bare Mg alloys. Nano-ZrO2 top coat which has completely sealed PEO bond coat is able to considerably delay aggressive ions transportation towards Mg alloy surface and significantly enhances corrosion resistance of Mg alloy in simulated body fluid（SBF） solution. Moreover, higher antibacterial activity was also observed in PEO/nano-ZrO2 coating against bacterial strains than that of the PEO coated and bare Mg alloys. This observation was attributed to the presence of ZrO2 nanoparticles which decelerate E. coli growth as a result of E. coli membranes.
基金Project supported by the Ministry of Higher Education of Malaysia and Research Management Center of UTM(Post-Doctoral part)
文摘Bi-layered thermally grown oxide （TGO） layer plays a major role in the spallation of Y2O3 stabilized ZrO2 （YSZ） layer form the bond coat in the thermal barrier coating （TBC） systems during oxidation. On the other hand, bi-layered TGO formation and growth in the TBC systems with nanostructured YSZ have not been deeply investigated during cyclic oxidation. Hence, Inconel 738/NiCrAlY/normal YSZ and Inconel 738/NiCrAlY/nano YSZ systems were pre-oxidized at 1000 °C and then subjected to cyclic oxidation at 1150 °C. According to microstructural observations, nanostructured YSZ layer over the bond coat should have less mi-cro-cracks and pinholes, due to the compactness of the nanostructure and the presence of nano zones that resulted in lower O infiltration into the nanothermal barrier coating system, formation of thinner and nearly continuous mono-layered thermally grown oxide on the bond coat during pre-oxidation, lower spinels formation at the Al2O3/YSZ interface and finally, reduction of bi-layered thermally grown oxide thickness during cyclic oxidation. It was found that pre-heat treatment and particularly coating microstructure could influence microstructural evolution （bi-layered TGO thickness） and durability of thermal barrier coating systems during cyclic oxidation.
基金partial financial support to this research from the Saskatchewan Health Research Foundation (SHRF)
文摘Infection is a major potential complication in the clinical treatment of bone injuries. Magnesium (Mg)-based composites are biodegradable and antibacterial biomaterials that have been employed to reduce infection following surgical implants. The aim of present study was to synthesize and in-vitro characterize Mg-based scaffolds containing silver for bone tissue engineering. Porous Mg-based scaffolds with four silver concentrations (i.e., 0, 0.5 wt.%, 1 wt.%, and 2 wt.%), denoted by Mg?Ca?Mn-Zn-xAg (MCMZ?xAg)(where x is the silver concentration), were fabricated by the space holder technique. The effects of silver concentration on pore architecture, mechanical properties, bioactivity, and zone of bacterial inhibition were investigated in-vitro. X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and fluorescence microscopy were utilized to characterize the obtained scaffolds. In-vitro corrosion test results indicated that the MCMZ scaffolds with lower silver content were more resistant to corrosion than those enriched with higher amounts of silver. Examination of the antibacterial activity showed that the MCMZ?Ag scaffolds exhibited superb potential with respect to suppressing the growth of Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus), in the inhibition zone around the MCMZ?Ag scaffolds, with increasing in the amount of incorporated silver;however, higher amounts of silver increased the cytotoxicity. Taken together, the results of this study demonstrate that the porous 0.5 wt.% Ag-containing scaffolds with interconnected pores, adequate mechanical properties, antibacterial activity, and cell adhesion are promising with respect to the repair and substitution of damaged and diseased bones.
文摘Potential engineering applications of magnesium(Mg)and Mg-based alloys,as the lightest structural metal,have made them a popular subject of study.However,the inferior corrosion and wear characteristics significantly limit their application range.It is widely recognized that surface treatment is the most commonly utilized technique for remarkably improving a substrate’s surface characteristics.Numerous methods have been introduced for the surface treatment of Mg and Mg-based alloys to improve their corrosion behavior and tribological performance.Among these,thermal spray(TS)technology provides several methods for deposition of various functional metallic,ceramic,cermet,or other coatings tailored to particular conditions.Recent researches have shown the tremendous potential for thermal spray coated Mg alloys for biomedical and industrial applications.In this context,the cold spray(CS)method,as a comparatively new TS coating technique,can generate the coating layer using kinetic energy rather than combined thermal and kinetic energies,like the high-velocity oxy-fuel(HVOF)spray method.Moreover,the CS process,as a revolutionary method,is able to repair and refurbish with a faster turnaround time;it also provides solutions that do not require dealing with the thermal stresses that are part of the other repair processes,such as welding or other TS processes using a high-temperature flame.In this review paper,the recently designed coatings that are specifically applied to Mg alloys(primarily for industrial applications)employing various coating processes are reviewed.Because of the increased utilization of CS technology for both 3D printed(additively manufactured)coatings and repair of structurally critical components,the most recent CS methods for the surface treatment,repair,and refurbishment of Mg alloys as well as their benefits and restrictions are then discussed and reviewed in detail.Lastly,the prospects of this field of study are briefly discussed,along with a summary of the presented work.
文摘Magnesium(Mg)-based materials are a new generation of alloys with the exclusive ability to be biodegradable within the human/animal body.In addition to biodegradability,their inherent biocompatibility and similar-to-bone density make Mg-based alloys good candidates for fabricating surgical bioimplants for use in orthopedic and traumatology treatments.To this end,nowadays additive manufacturing(AM)along with three-dimensional(3D)printing represents a promising manufacturing technique as it allows for the integration of bioimplant design and manufacturing processes specific to given applications.Meanwhile,this technique also faces many new challenges associated with the properties of Mg-based alloys,including high chemical reactivity,potential for combustion,and low vaporization temperature.In this review article,various AM processes to fabricate biomedical implants from Mg-based alloys,along with their metallic microstructure,mechanical properties,biodegradability,biocompatibility,and antibacterial properties,as well as various post-AM treatments were critically reviewed.Also,the challenges and issues involved in AM processes from the perspectives of bioimplant design,properties,and applications were identified;the possibilities and potential scope of the Mg-based scaffolds/implants are discussed and highlighted.
文摘This study investigates the effect of graphene oxide(GO)on the mechanical and corrosion behavior,antibacterial performance,and cell response of Mg–Zn–Mn(MZM)nanocomposite.MZM/GO nanocomposites with different amounts of GO(i.e.,0.5 wt%,1.0 wt%,and1.5 wt%)were fabricated by the semi-powder metallurgy method.The influence of GO on the MZM nanocomposite was analyzed through the hardness,compressive,corrosion,antibacterial,and cytotoxicity tests.The experimental results showed that,with the increase in the amount of GO(0.5 wt%and 1.5 wt%),the hardness value,compressive strength,and antibacterial performance of the MZM nanocomposite increased,whereas the cell viability and osteogenesis level decreased after the addition of 1.5 wt%GO.Moreover,the electrochemical examination results showed that the corrosion behavior of the MZM alloy was significantly enhanced after encapsulation in 0.5 wt%GO.In summary,MZM nanocomposites reinforced with GO can be used for implant applications because of their antibacterial performance and mechanical property.
基金the support provided by Islamic Azad University of Najafabad, Iran for this research。
文摘A type of polymer/ceramic coating was introduced on a magnesium-based nanocomposite, and the nanocomposite was evaluated for implant applications.The microstructure, corrosion, and bioactivity of the coated and uncoated samples were assessed.Mechanical alloying followed by sintering was applied to fabricate the Mg–3Zn–0.5Ag–15NiTi nanocomposite substrate.Moreover, different contents of poly(lactic-co-glycolic acid)(PLGA) coatings were studied, and 10 wt% of PLGA content was selected.The scanning electron microscopy(SEM) images of the bulk nanocomposite showed an acceptable homogenous dispersion of the Ni Ti nanoparticles(NPs) in the Mg-based matrix.In the in vitro bioactivity evaluation, following the immersion of the uncoated and coated samples in a simulated body fluid(SBF) solution, the Ca/P atomic ratio demonstrated that the apatite formation amount on the coated sample was greater than that on the uncoated nanocomposite.Furthermore, assessing the corrosion resistance indicated that the coatings on the Mg-based substrate led to a corrosion current density(icorr) that was considerably lower than that of the substrate.Such a condition revealed that the coating would provide an obstacle for the corrosion.Based on this study, the PLGA/hardystonite(HT) composite-coated Mg–3Zn–0.5Ag–15NiTi nanocomposite may be suitably applied as an orthopedic implant biomaterial.
基金supported financially by Ministry of Higher Education of Malaysia under the Vote Number 78610
文摘The influence of hydrofluoric acid（HF） treatment on the corrosion behavior of the Mg-0.5Ca alloys was investigated by immersion specimen in sodium hydroxide and HF solutions with various concentrations and durations at room temperature.Microstructural evolutions of the specimens were characterized by atomic force microscopy,X-ray diffraction,field-emission scanning electron microscopy.The corrosion resistance was examined through potentiodynamic polarization and immersion test in Kokubo solution.The results revealed that the fluoride treated Mg-0.5Ca alloys produced by immersion in 40% HF provided more uniform,dense and thicker coating layer（12.6 μm） compared with the 35% HF treated specimen.The electrochemical test showed that the corrosion resistance of fluoride treated specimen was 35 times higher compared with the untreated Mg-0.5Ca alloy specimen in Kokubo solution.In vitro degradation rate of the fluoride treated specimens was much lower than untreated Mg-0.5Ca alloy in Kokubo solution.After immersion test the surface of 40% HF treated sample showed a few corrosion dots,while untreated specimens were fully covered by corrosion products and delamination.Fluoride treated Mg-0.5Ca alloy with 40% HF is a promising candidate as biodegradable implants due to its low degradation kinetics and good biocompatibility.
文摘The effect of multi-step tempering on retained austenite content and mechanical properties of low alloy steel used in the forged cold back-up roll was investigated.Microstructural evolutions were characterized by optical microscope,X-ray diffraction,scanning electron microscope and Feritscope,while the mechanical properties were determined by hardness and tensile tests.The results revealed that the content of retained austenite decreased by about 2% after multi-step tempering.However,the content of retained austenite increased from 3.6% to 5.1% by increasing multi-step tempering temperature.The hardness and tensile strength increased as the austenitization temperature changed from 800 to 920 ℃,while above 920 ℃,hardness and tensile strength decreased.In addition,the maximum values of hardness,ultimate and yield strength were obtained via triple tempering at 520 ℃,while beyond 520 ℃,the hardness,ultimate and yield strength decreased sharply.
基金U.S.National Institute of Health-National Heart,Lung,and Blood Institute Grants R56HL163552 and R01HL168696 are acknowledged by J W D for funding work on biodegradable metals.
文摘Magnesium(Mg)and its alloys are revolutionizing the field of interventional surgeries in the medical industry.Their high biocompatibility,biodegradability,and a similar elastic modulus to natural bone make porous Mg-based structures potential candidates for orthopedic implants and tissue engineering scaffolding.However,fabricating and machining porous Mg-based structures is challenging due to their complexity and difficulties in achieving uniform or gradient porosity.This review aims to thoroughly explore various fabrication procedures used to create metallic scaffolds,with a specific focus on those made from Mg-based alloys.Both traditional manufacturing techniques,including the directional solidification of metal-gas eutectic technique,pattern casting,methods using space holders,and modern fabrication methods,which are based on additive manufacturing,are covered in this review article.Furthermore,the paper highlights the most important findings of recent studies on Mg-based scaffolds in terms of their microstructure specifications,mechanical properties,degradation and corrosion behavior,antibacterial activity,and biocompatibility(both in vivo and in vitro).While extensive research has been conducted to optimize manufacturing parameters and qualities of Mg-based scaffolds for use in biomedical applications,specifically for bone tissue engineering applications,further investigation is needed to fabricate these scaffolds with specific properties,such as high resistance to corrosion,good antibacterial properties,osteoconductivity,osteoinductivity,and the ability to elicit a favorable response from osteoblast-like cell lines.The review concludes with recommendations for future research in the field of medical applications.
