In this work,a novel ultrahigh-strength Al-10Zn-3.5Mg-1.5Cu alloy was fabricated by powder metallurgy followed by hot extrusion.Investigations on microstructural evolution and mechanical properties of the fabricated s...In this work,a novel ultrahigh-strength Al-10Zn-3.5Mg-1.5Cu alloy was fabricated by powder metallurgy followed by hot extrusion.Investigations on microstructural evolution and mechanical properties of the fabricated samples were carried out.The results show that the grain size of sintered samples matches with the powder particles after ball milling.The relative densities of sintered and hot extruded samples reach 99.1%and 100%,respectively.Owing to the comprehensive mechanism of grain refinement,aging and dispersion strengthening,the ultimate tensile strength,yield strength and elongation of the Al-10Zn-3.5Mg-1.5Cu alloy after hot extrusion and subsequent heat treatment achieve 810 MPa,770 MPa and 8%,respectively.展开更多
The almost completely dense copper was prepared by ultrafine copper powder prepared with both methods of electrolysis and novel water-gas atomization through cold isostatic pressing(CIP)and sintering under atmospheric...The almost completely dense copper was prepared by ultrafine copper powder prepared with both methods of electrolysis and novel water-gas atomization through cold isostatic pressing(CIP)and sintering under atmospheric hydrogen.Fine copper powder possesses the higher sintering driving force,thereby promoting shrinkage and densification during the sintering process.The grain size of sintered samples by electrolytic copper powder is smaller than that prepared by the atomized copper powder,and the twin crystals are particularly prone to forming in the former sintered microstructure due to the raw powder with low oxygen content and high residual stress originating from the CIP process.The relative density of samples by electrolytic and atomized powder at 1000℃ sintering temperature achieves 99.3%and 97.4%,respectively,significantly higher than that of the powder metallurgy copper parts reported in the literature.Correspondingly,the ultimate tensile strength and yield strength of samples by both kinds of copper powder are approximately similar,while the elongation of the sintered sample by the electrolytic powder(60%)is apparently higher than the atomized powder(44%).The superior performance of samples fabricated by electrolytic powder is inferred from the full density and low oxygen level for there is no cuprous oxide in the grain boundaries.展开更多
The biosynthetic time and accumulations of A-, B-, and C-type glutenin subunits in 7 winter wheat cultivars with different quality （strong, medium, weak gluten） were analyzed by SDS-PAGE. The results showed that no ...The biosynthetic time and accumulations of A-, B-, and C-type glutenin subunits in 7 winter wheat cultivars with different quality （strong, medium, weak gluten） were analyzed by SDS-PAGE. The results showed that no glutenin subunit was observed within 8 d after anthesis. Parts or all A-, B-, and C-type subunits appeared around day 12 in different cultivars. Other A-, B-, and C-type subunits appeared gradually. The accumulation of A-, B-, and C-type subunits fluctuated before maturity. The results of analysis of correlation between the ratios of A/T （total content of glutenin subunits）, A/C, AJ （B＋C）, （A＋B）/C, and （A＋B）/T and SDS-sedimentation value suggested that they were more significant. The negative correlation between the ratio of （B＋C）/T and SDS-sedimentation value was more significant, and the correlations between the ratio C/T and the SDS-sedimentation value were significantly negative.展开更多
基金Project(FRF-GF-19-012AZ)supported by the Fundamental Research Funds for the Central Universities,China。
文摘In this work,a novel ultrahigh-strength Al-10Zn-3.5Mg-1.5Cu alloy was fabricated by powder metallurgy followed by hot extrusion.Investigations on microstructural evolution and mechanical properties of the fabricated samples were carried out.The results show that the grain size of sintered samples matches with the powder particles after ball milling.The relative densities of sintered and hot extruded samples reach 99.1%and 100%,respectively.Owing to the comprehensive mechanism of grain refinement,aging and dispersion strengthening,the ultimate tensile strength,yield strength and elongation of the Al-10Zn-3.5Mg-1.5Cu alloy after hot extrusion and subsequent heat treatment achieve 810 MPa,770 MPa and 8%,respectively.
基金Project(92066205)supported by the National Natural Science Foundation of ChinaProject(2019-Z10)supported by the State Key Lab for Advanced Metals and Materials of ChinaProject(FRF-MP-20-52)supported by the Fundamental Research Funds for the Central Universities,China。
文摘The almost completely dense copper was prepared by ultrafine copper powder prepared with both methods of electrolysis and novel water-gas atomization through cold isostatic pressing(CIP)and sintering under atmospheric hydrogen.Fine copper powder possesses the higher sintering driving force,thereby promoting shrinkage and densification during the sintering process.The grain size of sintered samples by electrolytic copper powder is smaller than that prepared by the atomized copper powder,and the twin crystals are particularly prone to forming in the former sintered microstructure due to the raw powder with low oxygen content and high residual stress originating from the CIP process.The relative density of samples by electrolytic and atomized powder at 1000℃ sintering temperature achieves 99.3%and 97.4%,respectively,significantly higher than that of the powder metallurgy copper parts reported in the literature.Correspondingly,the ultimate tensile strength and yield strength of samples by both kinds of copper powder are approximately similar,while the elongation of the sintered sample by the electrolytic powder(60%)is apparently higher than the atomized powder(44%).The superior performance of samples fabricated by electrolytic powder is inferred from the full density and low oxygen level for there is no cuprous oxide in the grain boundaries.
文摘The biosynthetic time and accumulations of A-, B-, and C-type glutenin subunits in 7 winter wheat cultivars with different quality （strong, medium, weak gluten） were analyzed by SDS-PAGE. The results showed that no glutenin subunit was observed within 8 d after anthesis. Parts or all A-, B-, and C-type subunits appeared around day 12 in different cultivars. Other A-, B-, and C-type subunits appeared gradually. The accumulation of A-, B-, and C-type subunits fluctuated before maturity. The results of analysis of correlation between the ratios of A/T （total content of glutenin subunits）, A/C, AJ （B＋C）, （A＋B）/C, and （A＋B）/T and SDS-sedimentation value suggested that they were more significant. The negative correlation between the ratio of （B＋C）/T and SDS-sedimentation value was more significant, and the correlations between the ratio C/T and the SDS-sedimentation value were significantly negative.
